Geotechnical Characterization of Quito’s North-Central Zone as Applied to Deep Excavation in the Urban Setting

: This paper describes an in-depth soil characterization study in the La Carolina ﬁnancial district of Quito (Ecuador). As there was very little information available on the geotechnical structure of Quito’s volcanic soil, particularly in this area, where large-scale property development has taken place, the aim was to provide information on soil parameters to engineers working on large geotech-nical and civil engineering projects based on the results of a thorough and comprehensive study of such properties. A series of ﬁeld tests were performed at three different sites, where thin-walled tube samples were collected for lab testing to estimate the index properties and mechanical parameters. These index properties were then combined with conventional two-way drainage oedometer tests and stress-path triaxial testing to evaluate compressibility, stiffness and strength. The subsoil was found to be partly composed of slightly overconsolidated volcanic soils. X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) analyses were also conducted to determine mineralogical and microstructural features and evaluate their inﬂuence on the mechanical behavior of the volcanic soil. This type of research is frequently applied to the study of landslides in urban environments, where it is essential to understand their failure mechanisms, especially in slopes generated by the construction of important engineering works. Therefore, based on this geotechnical characterization study, parameters were subsequently determined for the Mohr–Coulomb (MC), Hardening Soil (HS), and Hardening Soil with Small-Strain Stiffness (HSsmall) soil constitutive models, and these were applied to a numerical study of the Soil Nailing system behavior for the construction of a ﬁve-level underground car parking structure of an important building located in the north-central sector of the city of Quito. It was veriﬁed that the HSsmall and HS constitutive soil models better reproduce the behavior of this type of structure. Finally, the multiple geotechnical parameters determined in this study signiﬁcantly contribute to the analysis of these structures in this soil type.


Introduction
Quito is in the Guayllabamba river basin at the foothills of the Pichincha volcano in northern Ecuador.The aim of this experimental study was to evaluate the geotechnical soil characteristics in the La Carolina district (Figure 1) based on the results of routine and advanced lab and field tests.As few studies of this nature have been conducted in the city, a thorough study of the soils in this district could prove to be of great assistance to engineers and city planners.The north-central zone of the city of Quito is characterized by moderate-to-large streets and avenues, with tall modern buildings and multi-story underground car parks, and thus, it was considered essential to carry out an extensive geotechnical study given the sparse amount of available information.
The subsoil in the zone object of this study comprises volcanic soils.As background information, Ecuador is a country with a great deal of volcanic activity and many volcanoes; however, very few complete studies have been carried out to characterize these types of materials [1].For example, O'Rourke and Crespo [2] studied the volcanic soils in the eastern zone of the city of Quito; Belloni and Morris [3] studied the behavior of volcanic debris soils as they relate to slope stability in the El Reventador Volcano zone, located some 100 km northeast of the city of Quito, in the northern zone of eastern Ecuador, and Vezzoli et al. [4] performed a characterization study of the pyroclastic deposits from the Cotopaxi Volcano, which is located some 75 km southeast of the city of Quito.In the northern Andes, the Ecuadorian arc features a significant number of Quaternary volcanoes distributed in a relatively confined area [5].Therefore, research groups such as Santamaria et al. [6], Andrade et al. [7], and Nauret et al. [8] have investigated important volcanoes in the central and northern regions of the Ecuadorian territory.
Volcanic soils constitute one of the most widely distributed groups in the world, especially in the Central and South American zones, Pacific Ocean islands, and the Caribbean, Africa, and Indonesia [9].Thus, authors such as Bommer et al. [9], Crosta et al. [10], Gonzalez de Vallejo et al. [11], del Potro and Hürlimann [12], and Brandes and Nakayama [13] have presented various detailed surveys on volcanic soils at the international level, in which they present the different characteristics of these soils, focusing mainly on their basic properties, soil classification, compression and strength properties.However, studies carried out by researchers such as Hürlimann et al. [14], Moon et al. [15], Avşar et al. [16], and Okewale and Coop [17], in addition to the abovementioned properties, also include mineralogy and microstructure analyses.Some of the abovementioned studies are consistent in that volcanic soils mainly characterized by their high porosity and low bulk density were predominantly made up of silts and sands.Other studies are also in agreement for lightly cemented volcanic soils, such as the surveys by Yamanouchi and Murata [18] in their study of Japan's volcanic soils.
This study was carried out at three boreholes strategically distributed throughout the area that coincide with the construction of important building projects, designated as AMA1 (Río Amazonas Avenue), JAP1 (Japón Street), and AUS1 (Austria Street), using the The north-central zone of the city of Quito is characterized by moderate-to-large streets and avenues, with tall modern buildings and multi-story underground car parks, and thus, it was considered essential to carry out an extensive geotechnical study given the sparse amount of available information.
The subsoil in the zone object of this study comprises volcanic soils.As background information, Ecuador is a country with a great deal of volcanic activity and many volcanoes; however, very few complete studies have been carried out to characterize these types of materials [1].For example, O'Rourke and Crespo [2] studied the volcanic soils in the eastern zone of the city of Quito; Belloni and Morris [3] studied the behavior of volcanic debris soils as they relate to slope stability in the El Reventador Volcano zone, located some 100 km northeast of the city of Quito, in the northern zone of eastern Ecuador, and Vezzoli et al. [4] performed a characterization study of the pyroclastic deposits from the Cotopaxi Volcano, which is located some 75 km southeast of the city of Quito.In the northern Andes, the Ecuadorian arc features a significant number of Quaternary volcanoes distributed in a relatively confined area [5].Therefore, research groups such as Santamaria et al. [6], Andrade et al. [7], and Nauret et al. [8] have investigated important volcanoes in the central and northern regions of the Ecuadorian territory.
Volcanic soils constitute one of the most widely distributed groups in the world, especially in the Central and South American zones, Pacific Ocean islands, and the Caribbean, Africa, and Indonesia [9].Thus, authors such as Bommer et al. [9], Crosta et al. [10], Gonzalez de Vallejo et al. [11], del Potro and Hürlimann [12], and Brandes and Nakayama [13] have presented various detailed surveys on volcanic soils at the international level, in which they present the different characteristics of these soils, focusing mainly on their basic properties, soil classification, compression and strength properties.However, studies carried out by researchers such as Hürlimann et al. [14], Moon et al. [15], Avşar et al. [16], and Okewale and Coop [17], in addition to the abovementioned properties, also include mineralogy and microstructure analyses.Some of the abovementioned studies are consistent in that volcanic soils mainly characterized by their high porosity and low bulk density were predominantly made up of silts and sands.Other studies are also in agreement for lightly cemented volcanic soils, such as the surveys by Yamanouchi and Murata [18] in their study of Japan's volcanic soils.
This study was carried out at three boreholes strategically distributed throughout the area that coincide with the construction of important building projects, designated as AMA1 (Río Amazonas Avenue), JAP1 (Japón Street), and AUS1 (Austria Street), using the Standard Penetration Test (SPT) to measure each meter of depth to a depth of 25 m.
The locations of the three boreholes are shown in Figure 2. The lab tests carried out at the Geotechnical Engineering Laboratory of the Universitat Politècnica de València (Spain) on disturbed and undisturbed samples from boreholes AMA1, JAP1, and AUS1 (which were stored in the laboratory's humidity chamber at a constant relative humidity of 100%) were based on four main characteristics: the index, compression, and strength properties, as well as deformation parameters under deviatoric loading.
Sustainability 2023, 15, x FOR PEER REVIEW 3 of 32 Standard Penetration Test (SPT) to measure each meter of depth to a depth of 25 m.The locations of the three boreholes are shown in Figure 2. The lab tests carried out at the Geotechnical Engineering Laboratory of the Universitat Politècnica de València (Spain) on disturbed and undisturbed samples from boreholes AMA1, JAP1, and AUS1 (which were stored in the laboratory's humidity chamber at a constant relative humidity of 100%) were based on four main characteristics: the index, compression, and strength properties, as well as deformation parameters under deviatoric loading.Furthermore, as part of this study, X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) analyses were conducted to obtain the mineralogical and microstructural characteristics and obtain further parameters to compare with the volcanic soil studies carried out by other researchers.
Comprehensive geotechnical characterization studies are applicable to the investigation of landslides in urban environments in their different phases of analysis, design, monitoring, or landslide prevention.These natural (geological) or anthropogenic disasters demand specialized studies.Among the geological factors that can be mentioned are the presence of incompetent lithology, fault zones, slopes with high critical angles, and seismic activity.In terms of anthropogenic factors, there are modifications of slope gradients, constructions on slopes, and vibrations produced by heavy traffic [19].Furthermore, a combination of factors, such as dense urban development, mountainous terrain, and intense seasonal rainfall, has led to serious landslide issues [20].However, slope failure mainly occurs during heavy rainfall events when slow-moving regressive landslides turn into earth flows and mudflows [21].
Human activities are often responsible for inducing landslides in populated areas [22][23][24][25].Excavation-induced landslides are typically observed in mining areas, particularly in sectors where hydrogeological conditions contribute to slope instability.However, such landslides are particularly prevalent in urban environments where human activities involve construction work, with or without excavation.Landslides often follow unplanned excavations, but uncontrolled loading resulting from any type of construction work in the upper part of a slope may also trigger a landslide.Additionally, new human settlements frequently necessitate urban and industrial development in steeply sloping Furthermore, as part of this study, X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) analyses were conducted to obtain the mineralogical and microstructural characteristics and obtain further parameters to compare with the volcanic soil studies carried out by other researchers.
Comprehensive geotechnical characterization studies are applicable to the investigation of landslides in urban environments in their different phases of analysis, design, monitoring, or landslide prevention.These natural (geological) or anthropogenic disasters demand specialized studies.Among the geological factors that can be mentioned are the presence of incompetent lithology, fault zones, slopes with high critical angles, and seismic activity.In terms of anthropogenic factors, there are modifications of slope gradients, constructions on slopes, and vibrations produced by heavy traffic [19].Furthermore, a combination of factors, such as dense urban development, mountainous terrain, and intense seasonal rainfall, has led to serious landslide issues [20].However, slope failure mainly occurs during heavy rainfall events when slow-moving regressive landslides turn into earth flows and mudflows [21].
Human activities are often responsible for inducing landslides in populated areas [22][23][24][25].Excavation-induced landslides are typically observed in mining areas, particularly in sectors where hydrogeological conditions contribute to slope instability.However, such landslides are particularly prevalent in urban environments where human activities involve construction work, with or without excavation.Landslides often follow unplanned excavations, but uncontrolled loading resulting from any type of construction work in the upper part of a slope may also trigger a landslide.Additionally, new human settlements frequently necessitate urban and industrial development in steeply sloping mountainous regions, rendering these areas vulnerable and increasing the likelihood of landslides.
The stability of a slope resulting from excavation has always been a contentious issue.According to Burland et al. [26], Tsidzi [27], Bozzano et al. [28], Erginal et al. [23], and Zhang et al. [25], slope failure is caused by the release of induced stresses due to excavation.Many studies have demonstrated that geological and geotechnical investigations are essential to comprehend the failure mechanism of an earth structure, which will enable the creation of an appropriate geological model in numerical simulations [25].Due to congested urban environments, current deep excavations are complex and require more specialized analyses to meet the needs of all stakeholders [29].On the other hand, insufficient geotechnical and geological investigations and the inadequate interpretation of ground conditions often lead to slope failure and the subsequent costs of repair work [30].All of the above clearly justifies the need for a comprehensive geotechnical characterization study for landslide analysis and evaluation.
Throughout history and across the globe, numerous landslides induced by prior human activities have been identified.In Busan (South Korea) in the late 1990s, cut slopes were created on a hillside to provide space for housing and industry.However, later analyses revealed that the original investigations, designs, and subsequent studies were inadequate, resulting in the slope failing six times despite nine reassessment surveys and the implementation of various remediation alternatives over a 7-year period until a catastrophic collapse occurred in 2002 [30].
In contrast, in Praia de Boa Viagem (Brazil) in 2003, a 31-meter excavation was carried out to construct a building.To ensure stability, two levels of anchored walls were planned.However, when the upper wall was nearly completed, a crack appeared at its top, prompting a halt to construction for further investigation [31].These studies revealed the presence of clay minerals with high activity and low shear strength that were not identified in the initial study.Consequently, the walls were reinforced with additional anchors, and a Soil Nailing system was incorporated.During and after the construction, the excavation was monitored using load tests on the anchors, inclinometers to control horizontal ground deformations, and an electronic distance-measuring device to monitor horizontal and vertical ground surface and wall movements.Strain Gauges were also installed on the steel bars to monitor their tension.
In March 2011, a landslide took place on a slope around 18.3 m in height in Santa Clara, California (USA), and according to specialized studies conducted afterward, it was found that the landslide was induced by a significant cut made in the terrain along the bottom of the slope between 2000 and 2004 [32].Before the landslide, a residential structure had been constructed near the slope's base.
On the other hand, given the involvement of anthropogenic factors, the construction of geotechnical engineering works commonly generates risks that require special attention.Thus, in the construction of most underground building structures in the Ecuadorian capital, the Soil Nailing technique is frequently applied during the excavation process as a method for reinforcing the ground during the excavation process, with some variations according to the equipment available in the region and the specifications of each project.However, this technique, which has proved to be effective for the management of soil excavations in the city of Quito, currently lacks local research, whether theoretical, numerical, or experimental, based on the geotechnical properties of the volcanic soils that characterize the area [1].
The Soil Nailing technique has been successfully applied globally to slope stabilization in several geotechnical engineering projects in countries such as the United States [33], Chile [34], China [35], Ireland [36], and Brazil [31], among others.Similarly, several numerical studies of the behavior of this type of structure have been carried out, such as those presented by Fan and Luo [37], Singh and Sivakumar Babu [38], Wei and Cheng [39], Rabie [40], Rawat and Gupta [41], Bayat et al. [42], and Capa et al. [43], among others.These investigations have verified the technique's high degree of efficiency in its practical application and are supported by important numerical analyses.
In view of the above and as an application to the geotechnical characterization study, a numerical analysis is presented using the finite element method with PLAXIS 2D [44,45] of a typical Soil Nailing structure for the construction of a building with 5 underground parking levels (h = 15.5 m) and 15 stories in height.This building was constructed from 2017 to 2020 and is located precisely in the area of the JAP1 borehole (Figure 2), in the north-central area of the city of Quito.For the analysis with PLAXIS 2D [44][45][46], the Mohr-Coulomb (MC), Hardening Soil (HS), and Hardening Soil with Small-Strain Stiffness (HSsmall) soil constitutive models were considered.This analysis focuses primarily on the evolution of tensile forces in the anchor bars and the analysis of horizontal displacements of the facing and settlements in the soil induced by basement-level construction.This research additionally includes an analysis of the factors of safety (FoSs) established during the different construction phases and carried out by means of limit equilibrium methods and the finite element method.
The analysis of all the aforementioned variables is crucial in the stability study of ground reinforcement structures applied in the field of urban excavations in civil construction works.Naturally, having comprehensive geotechnical characterization studies also allows for the creation of numerical models that more accurately reflect reality.

Geological Setting
The Ecuadorian Andes mountain range covers an area of approximately 650 km by 150 km [47], which crosses Ecuador from the south to the north, predominately in the NNE-SSW direction [48].This mountain chain began to develop at the end of the Cretaceous period as a result of the subduction movements of the Nazca Plate and the Carnegie Ridge (an underwater mountain ridge situated on the Nazca Plate) under the South American plate, generating a compressive tectonic regime dominating from E-W up until present times [47][48][49] (Figure 3).The Carnegie Ridge is emerging in the active Galapagos hotspot [50].
In Ecuador, the volcanic arc related to the subduction of the Nazca Plate has a width of 120 km and is divided into three regions: the forearc, extending along the Western Range or Cordillera Occidental; the main arc, situated in the Eastern Range or Cordillera Real; and the back-arc, located in the upper Amazon regions.The volcanoes in the forearc (Pululahua, Atacazo, Illiniza, Quilotoa, and the Pichincha Volcanic Complex) are mainly dacitic centers, whereas those in the main and back-arc (Antisana, Cotopaxi, Tungurahua, Sangay, and El Reventador) are mainly andesitic in composition [51].The Inter-Andean Depression, which has been evolving since the Miocene epoch [52,53], is located between the Western Range and the Eastern Range.During the development of the Inter-Andean Depression, tectonic rearrangements of the Late Miocene progressively led to the formation of various basins that were filled with alluvial, fluvial, lacustrine, and volcanic deposits, including the Quito Basin [54].
The urban area of Quito is situated within the Quito Basin, oriented in a north-south direction.The study area is positioned to the east of the Pichincha Volcanic Complex.The Quito Basin's eastern boundary is defined by an actively moving reverse fault that dips toward the west [55].The curved geometry of this fault is likely a consequence of the Pichincha Volcanic Complex's propagation [51].
In terms of stratigraphy, the area of interest (north-central Quito) corresponds to recent deposits that rest on the Cangahua Formation (tufa and volcanic ash from the Quaternary period).The northern, southern, and eastern zones of the area of interest are stratigraphically characterized by lacustrine fluvial sedimentary deposits [56] with clearly defined stratified layers of sandy silts and dark brown, light brown, and yellowish-gray sands, with some pumice lapilli.Decomposed organic matter is present in most of the surface layers.The western zone consists of a colluvial deposit [56] with no clear deposition sequence and generally consists of materials of varied granulometric size, including gravel and boulders.On the other hand, the geological and geotechnical study for Line 1 of the Quito Metro [59] indicated the presence of surface fill soils in several areas of La Carolina.However, in the three drillings carried out during this study and located relatively close to the Quito Metro study, we did not detect any such materials.

Standard Penetration Test
The most widely used and cost-effective in situ test to obtain subsurface information is the Standard Penetration Test (SPT), which measures soil resistance to penetration at any given depth.It can also be used to estimate the properties of granular soils [60], correlate the undrained shear strength of cohesive soils, and calculate the soil-bearing capacity and settlement.In this study, the SPT was carried out in accordance with the ASTM On the other hand, the geological and geotechnical study for Line 1 of the Quito Metro [59] indicated the presence of surface fill soils in several areas of La Carolina.However, in the three drillings carried out during this study and located relatively close to the Quito Metro study, we did not detect any such materials.The most widely used and cost-effective in situ test to obtain subsurface information is the Standard Penetration Test (SPT), which measures soil resistance to penetration at any given depth.It can also be used to estimate the properties of granular soils [60], correlate the undrained shear strength of cohesive soils, and calculate the soil-bearing capacity and settlement.In this study, the SPT was carried out in accordance with the ASTM D1586 standard [61].Figure 4a shows the penetration depth plotted against the number of blows (N SPT ) obtained for the penetration resistance test in boreholes JAP1, AMA1, and AUS1.

Geotechnical Characterization Study
Sustainability 2023, 15, x FOR PEER REVIEW 7 of 32 D1586 standard [61].Figure 4a shows the penetration depth plotted against the number of blows (NSPT) obtained for the penetration resistance test in boreholes JAP1, AMA1, and AUS1.Furthermore, the preconsolidation stress was estimated by oedometer testing.Figure 4b shows the corresponding overconsolidation ratios (OCRs).The values range from 1.62 at a depth of 3.5 m to 1.30 at 14.5 m.

Soil Sampling
A geotechnical site investigation is the process of soil characterization, which requires undisturbed high-quality samples.Tube sampling is the easiest and most cost-effective manner of sampling, although it has been associated with sample disturbance.In this study, 600 mm × 78 mm diameter stainless-steel tubes and a wall thickness of t = 1.50 mm were used to collect samples from boreholes JAP1 and AMA1.The ratio of the external diameter to wall thickness, De/t, was 50.7, which is higher than the minimum De/t recommended by Ladd and DeGroot [62].

Index Properties and Soil Composition
All sample testing was carried out in accordance with ASTM [63] and UNE [64] standards.This section provides the index properties and soil composition data obtained from the tests.

Natural Water Content and Atterberg Limits
Variation values of the natural water content (wnat), liquid limit (LL), and plastic limit (PL) are shown in Figure 5a-c.The depth profile of natural water content in borehole JAP1 ranged from 13% to 50% and decreased normally with depth to 16 m.In AMA1, a uniform range of values was found from 12% to 26%, while in AUS1, the natural water content distribution was between 9% and 33%.The plastic limit (PL) ranged from 16 to 34 (average ~25), while the liquid limit (LL) values ranged from 18 to 64 (average ~35).Figure 5d shows the depth profile of the liquidity index (LI), which ranges from −2.0 to 1.0.Furthermore, the preconsolidation stress was estimated by oedometer testing.Figure 4b shows the corresponding overconsolidation ratios (OCRs).The values range from 1.62 at a depth of 3.5 m to 1.30 at 14.5 m.

Soil Sampling
A geotechnical site investigation is the process of soil characterization, which requires undisturbed high-quality samples.Tube sampling is the easiest and most cost-effective manner of sampling, although it has been associated with sample disturbance.In this study, 600 mm × 78 mm diameter stainless-steel tubes and a wall thickness of t = 1.50 mm were used to collect samples from boreholes JAP1 and AMA1.The ratio of the external diameter to wall thickness, De/t, was 50.7, which is higher than the minimum De/t recommended by Ladd and DeGroot [62].

Index Properties and Soil Composition
All sample testing was carried out in accordance with ASTM [63] and UNE [64] standards.This section provides the index properties and soil composition data obtained from the tests.

Natural Water Content and Atterberg Limits
Variation values of the natural water content (w nat ), liquid limit (LL), and plastic limit (PL) are shown in Figure 5a-c.The depth profile of natural water content in borehole JAP1 ranged from 13% to 50% and decreased normally with depth to 16 m.In AMA1, a uniform range of values was found from 12% to 26%, while in AUS1, the natural water content distribution was between 9% and 33%.The plastic limit (PL) ranged from 16 to 34 (average ~25), while the liquid limit (LL) values ranged from 18 to 64 (average ~35).Figure 5d shows the depth profile of the liquidity index (LI), which ranges from −2.0 to 1.0.Figure 6 shows Casagrande plasticity charts for samples from boreholes JAP1, AMA1, and AUS1.It is evident that all the samples lie close to the A-line.Most of those from JAP1 are classified as silts and clays with low-to-high plasticity, while most from AMA1 and AUS1 are silts and clays with low-to-intermediate plasticity.

Particle Size Distributions
Figure 7a shows the particle size distribution profiles for specimens from borehole JAP1.Silt content ranged from 37 to 64% (average ~53%) between depths of 1.0 m and 14.5 m, although sand content was predominant below the 14.5 m level, with maximum values up to 71%.

Particle Size Distributions
Figure 7a shows the particle size distribution profiles for specimens from borehole JAP1.Silt content ranged from 37 to 64% (average ~53%) between depths of 1.0 m and 14.5 m, although sand content was predominant below the 14.5 m level, with maximum values up to 71%. Figure 7b shows that the particle size distribution for samples from borehole AMA1 is fairly constant at all depths, and sand content ranged from 28% to 75% (average ~52%).Figure 7c shows the particle size distribution for specimens from borehole AUS1, in which fine content was predominant throughout (42% to 84%).According to the Unified Soil Classification System (USCS), these soils are classified as ML, MH, CL, CL-ML, and SM.By way of comparison, the volcanic soils from the eastern zone of the city of Quito studied by O'Rourke and Crespo [2] were found to consist of material containing approximately 60-65% fine sand and 10-15% clay by weight, with the remaining fraction being silt.

Specific Gravity and Bulk Density
The specific gravity values are reported in Figure 8a.In general, these values are between 2.35 and 2.65 in borehole JAP1.In AMA1 samples, these range from 2.61 to 2.  Figure 7b shows that the particle size distribution for samples from borehole AMA1 is fairly constant at all depths, and sand content ranged from 28% to 75% (average ~52%).Figure 7c shows the particle size distribution for specimens from borehole AUS1, in which fine content was predominant throughout (42% to 84%).According to the Unified Soil Classification System (USCS), these soils are classified as ML, MH, CL, CL-ML, and SM.By way of comparison, the volcanic soils from the eastern zone of the city of Quito studied by O'Rourke and Crespo [2] were found to consist of material containing approximately 60-65% fine sand and 10-15% clay by weight, with the remaining fraction being silt.

Specific Gravity and Bulk Density
The specific gravity values are reported in Figure 8a.In general, these values are between 2.35 and 2.65 in borehole JAP1.In AMA1 samples, these range from 2.61 to 2.

Void Ratio and Porosity
Void ratio values are shown in Figure 9a.These vary between 0.88 and 1.92 in JAP1 and between 0.49 and 0.99 in AMA1.These void ratio values are within the range of those of the volcanic soils studied by O'Rourke and Crespo [2], Hürlimann et al. [14], and Bommer et al. [9].
Figure 9b shows the porosity values, which were found to range between 47% and 66% in JAP1 and between 33% and 50% in AMA1.Likewise, the studied soils have high porosity values, in agreement with the volcanic soil studies by O'Rourke and Crespo   The Bernard Calcimeter method was used to determine the calcium carbonate content of the specimens obtained from boreholes JAP1 and AMA1.The carbonate content variation with depth is shown in Figure 10a.The values range from 4.0% to 5.7% for the

Carbonate Content and Organic Content
The Bernard Calcimeter method was used to determine the calcium carbonate content of the specimens obtained from boreholes JAP1 and AMA1.The carbonate content variation with depth is shown in Figure 10a.The values range from 4.0% to 5.7% for the samples from JAP1 and between 3.7% and 6.2% for the specimens from AMA1.The Bernard Calcimeter method was used to determine the calcium carbon tent of the specimens obtained from boreholes JAP1 and AMA1.The carbonate variation with depth is shown in Figure 10a.The values range from 4.0% to 5.7% samples from JAP1 and between 3.7% and 6.2% for the specimens from AMA1.The potassium permanganate method was used to determine the organic content (OC) of samples from JAP1 and AMA1. Figure 10b shows the organic content variation with depth, which ranges between 0.35% and 3.61% for specimens from JAP1 and between 0.76% and 2.05% for those from AMA1.In both cases, the values show a clear tendency to decrease with depth.

Microstructure
Scanning Electron Microscopy (SEM) was performed with a Model JSM 6300 Scanning Microscope using intact oven-dried samples.Plagioclase, Augite, Tremolite, Diopside, and Cristobalite-Quartz are dominant in each sample, consistent with the values recorded in the mineralogical analysis (Mineralogy section).Figure 12 shows the microstructures of specimens from JAP1 and AMA1.Gas bubbles and organic matter can be identified in Figure 12b and could be the main reason for the low density values.

Microstructure
Scanning Electron Microscopy (SEM) was performed with a Model JSM 6300 Scanning Microscope using intact oven-dried samples.Plagioclase, Augite, Tremolite, Diopside, and Cristobalite-Quartz are dominant in each sample, consistent with the values recorded in the mineralogical analysis (Mineralogy section).Figure 12 shows the microstructures of specimens from JAP1 and AMA1.Gas bubbles and organic matter can be identified in Figure 12b and could be the main reason for the low density values.

Compression Properties
Conventional two-way drainage oedometer tests were carried out on undisturbed specimens to evaluate the soil compression parameters, in accordance with the ASTM D2435 standard [66].The diameters of stainless-steel oedometric rings used were 45 mm, 50 mm, and 70 mm, with a height of 20 mm.Each load increment was maintained for 24 h.Overburden stress was increased from 5 kPa to 1000 kPa, but some samples were loaded up to 2000 kPa.
It is common and frequent for these types of tests to be performed on samples of clayey strata.However, in this study, oedometric tests were carried out on samples comprising mostly sand, an uncommon situation that is nevertheless not incorrect.On the contrary, oedometric curves that can be applicable to the analysis of vertical deformations

Compression Properties
Conventional two-way drainage oedometer tests were carried out on undisturbed specimens to evaluate the soil compression parameters, in accordance with the ASTM D2435 standard [66].The diameters of stainless-steel oedometric rings used were 45 mm, 50 mm, and 70 mm, with a height of 20 mm.Each load increment was maintained for 24 h.
Overburden stress was increased from 5 kPa to 1000 kPa, but some samples were loaded up to 2000 kPa.
It is common and frequent for these types of tests to be performed on samples of clayey strata.However, in this study, oedometric tests were carried out on samples comprising mostly sand, an uncommon situation that is nevertheless not incorrect.On the contrary, oedometric curves that can be applicable to the analysis of vertical deformations in terrain with volcanic soils consisting mostly of sand, under different load solicitations, were determined.In this study, all samples from borehole AMA1 were composed of silty sands.
To make the research more comprehensive, repetitive instances of "load-unload-reloadunload" states were performed on several samples, which required many days of analysis, considering that each load and unload step represents a day of testing.However, this allowed for verification that the unload curves are practically parallel in both unload instances.
Additionally, advanced soil constitutive models such as Hardening Soil (HS) and Hardening Soil with Small-Strain Stiffness (HSsmall) require the oedometric tangent modulus, which is precisely determined through these tests [46].Therefore, a practical application that normally yields consistent and more reliable results is the analysis of Soil Nailing retaining structures with these soil constitutive models.These structures are common in the control of landslides in urban environments and often have multilayer strata with variations of fine soils and sandy soils, and thus, conducting such oedometric tests on sandy soils is clearly justified.
Figure 13 shows typical one-dimensional compression oedometer test results for samples from boreholes JAP1 and AMA1 in terms of the effective stress and the corresponding void ratio.
Sustainability 2023, 15, x FOR PEER REVIEW 14 of 32 Figure 13 shows typical one-dimensional compression oedometer test results for samples from boreholes JAP1 and AMA1 in terms of the effective stress and the corresponding void ratio.Figure 14a shows the relationship between the compression index (Cc) and the natu- Figure 14a shows the relationship between the compression index (C c ) and the natural moisture content (w nat ) and liquid limit (LL) for soils from JAP1 and AMA1. Figure 14b shows the correlation between the swelling index (C s ) and the natural moisture content (w nat ) and liquid limit (LL).Figure 14c shows the relationship between compression (C c ) and swelling indexes (C s ) versus initial void ratios (e 0 ).C c generally presents a good correlation with e 0 or w nat for most clay types [67].
x FOR PEER REVIEW 15 of 32 The ratio of Cc/Cs is a constant value and, in these cases, varies between 6 and 10.

Strength Properties
The shear strength of soil is its ability to resist failure and displacement between its particles when acted upon by an external force.This concept is fundamental when estimating the lateral soil pressure on retaining structures and in slope stability analysis.
In this study, consolidated-undrained triaxial tests (CU) and consolidated-drained triaxial tests (CD) were carried out in the hydraulic stress path cells of the Geotechnical Engineering Laboratory of the Universitat Politècnica de València.These analyses are the only ones to be performed to date in this specific region and should provide a valuable resource that will prove useful for future research.

Undrained Shear Strength Properties
The undrained soil shear strength plays a fundamental role in geotechnical engineering, providing important information to calculate the pressures exerted by soils in un- C c = 0.0061 (LL − 16.50) C c = 0.212 (e 0 − 0.212) C s = 0.0007 (w nat − 5.57) C s = 0.0006 (LL − 14) C s = 0.0284 (e 0 − 0.342) The ratio of C c /C s is a constant value and, in these cases, varies between 6 and 10.

Strength Properties
The shear strength of soil is its ability to resist failure and displacement between its particles when acted upon by an external force.This concept is fundamental when estimating the lateral soil pressure on retaining structures and in slope stability analysis.
In this study, consolidated-undrained triaxial tests (CU) and consolidated-drained triaxial tests (CD) were carried out in the hydraulic stress path cells of the Geotechnical Engineering Laboratory of the Universitat Politècnica de València.These analyses are the only ones to be performed to date in this specific region and should provide a valuable resource that will prove useful for future research.

Undrained Shear Strength Properties
The undrained soil shear strength plays a fundamental role in geotechnical engineering, providing important information to calculate the pressures exerted by soils in undrained conditions (short-term stability) and the bearing capacity, for example, in soils supporting gravity wall foundations.It is also an indicator of soil behavior, in association with other engineering properties.
In this study, consolidated-undrained (CU) triaxial compression tests with pore water pressure measurements were carried out in accordance with the ASTM D4767 standard [68].A very fine wire saw was used to trim the specimens to a diameter of 38 mm and a height of 76 mm in a soil lathe.Each triaxial test comprised three different stages: (1) saturation, (2) consolidation, and (3) shearing under undrained conditions [69].A stress-controlled saturation ramp was used until the point when the cell and back-water pressures reached 610 and 600 kPa, respectively.These values were held for approximately 24 h, after which Skempton's parameter B was determined, finding the values to be higher than 0.96 in every instance.All the specimens followed isotropic consolidation, in which pore water drainage was provided at the top of the sample.At the same time, the excess pore water pressure was measured with a pore pressure transducer connected to the bottom drainage line.Each specimen was then subjected to undrained shearing, with an axial displacement rate equal to 0.03 mm/min.The q-p plane is used to represent the test results; thus, p = (σ 1 + 2σ 3 )/3 and q = σ 1 -σ 3 , where σ 1 is the stress applied to a test specimen in the vertical (axial) direction, and σ 3 is the all-round pressure applied to a test specimen in the triaxial cell chamber.
Different failure criteria are used to determine the shear strength of a soil sample, including the peak deviator stress, maximum principal stress ratio, limiting strain, critical state, and residual stress.In this study, the maximum stress ratio σ 1 /σ 3 criterion was adopted as a failure criterion, from which the soil's shear strength is determined.This ratio provides a better correlation of shear stress versus normal stress in Mohr stress circles at failure.The ratio is equal to 1 at the start of the test, because in this stage, σ' 1 = σ' 3 .The maximum value of σ 1 /σ 3 does not necessarily occur at the same strain as the peak deviator stress.Peak values of the stress ratio σ 1 /σ 3 vary between 4.00 and 5.35, with the axial strain, ε s , ranging from 3.75% to 6.00%, whereas the post-peak values of this stress ratio range from 3.55 to about 4.65.Figure 15a shows the variation in the stress ratio, σ 1 /σ 3 , with the axial strain, ε s , for samples from boreholes JAP1 and AMA1.The variation in the stress ratio, q/p , with the axial strain, ε s , is shown in Figure 15b.In this case, the post-peak values of the stress ratio vary between 1.35 and 1.65.

5, x FOR PEER REVIEW
16 of 32 the excess pore water pressure was measured with a pore pressure transducer connected to the bottom drainage line.Each specimen was then subjected to undrained shearing, with an axial displacement rate equal to 0.03 mm/min.The q-p′ plane is used to represent the test results; thus, p′ = (σ′1 + 2σ′3)/3 and q = σ′1 -σ′3, where σ′1 is the stress applied to a test specimen in the vertical (axial) direction, and σ′3 is the all-round pressure applied to a test specimen in the triaxial cell chamber.
Different failure criteria are used to determine the shear strength of a soil sample, including the peak deviator stress, maximum principal stress ratio, limiting strain, critical state, and residual stress.In this study, the maximum stress ratio σ′1/σ′3 criterion was adopted as a failure criterion, from which the soil's shear strength is determined.This ratio provides a better correlation of shear stress versus normal stress in Mohr stress circles at failure.The ratio is equal to 1 at the start of the test, because in this stage, σ'1 = σ'3.The maximum value of σ′1/σ′3 does not necessarily occur at the same strain as the peak deviator stress.Peak values of the stress ratio σ′1/σ′3 vary between 4.00 and 5.35, with the axial strain, εs, ranging from 3.75% to 6.00%, whereas the post-peak values of this stress ratio range from 3.55 to about 4.65.Figure 15a shows the variation in the stress ratio, σ′1/σ′3, with the axial strain, εs, for samples from boreholes JAP1 and AMA1.The variation in the stress ratio, q/p′, with the axial strain, εs, is shown in Figure 15b.In this case, the post-peak values of the stress ratio vary between 1.35 and 1.65.Figure 16 shows the stress-strain curves, q-εs, with the evolution of pore pressure (u), obtained for samples from boreholes JAP1 and AMA1. Figure 16 shows the stress-strain curves, q-ε s , with the evolution of pore pressure (u), obtained for samples from boreholes JAP1 and AMA1.The stress ratio q/p′ behavior was classified into two main groups, as seen in Figure 17, which shows that the undrained strength in compression was determined using the critical soil mechanics concept.The (M) slope of the critical state line in compression [70,71] is obtained by Equation (7).The stress ratio q/p behavior was classified into two main groups, as seen in Figure 17, which shows that the undrained strength in compression was determined using the critical soil mechanics concept.The (M) slope of the critical state line in compression [70,71] is obtained by Equation (7).The secant friction angle, Ø′sec, was estimated for axial strains greater than 12%.Average friction angles of 35° (specimens from depths of 3.50 m to 7.50 m) and 38° (specimens from depths of 9.00 m to 14.50 m) constitute the post-peak response of samples from JAP1 and AMA1.This relationship between Ø′sec and sample depth, however, is not definitive, given that some factors (such as particle shape, size distribution and configuration, grain mineralogy, void ratio, water content, and previous stress history) can affect the soil strength measured in a lab test [72].
Figure 18 shows the stress paths in the q-p′ plane for the samples from JAP1 and AMA1 under triaxial conditions.The soil behavior under shearing is easily observed in the effective stress paths shown in these figures.Peak friction angles between 34° and 38° were estimated in triaxial compression for these two borehole samples.The secant friction angle, Ø sec , was estimated for axial strains greater than 12%.Average friction angles of 35 • (specimens from depths of 3.50 m to 7.50 m) and 38 • (specimens from depths of 9.00 m to 14.50 m) constitute the post-peak response of samples from JAP1 and AMA1.This relationship between Ø sec and sample depth, however, is not definitive, given that some factors (such as particle shape, size distribution and configuration, grain mineralogy, void ratio, water content, and previous stress history) can affect the soil strength measured in a lab test [72].
Figure 18 shows the stress paths in the q-p plane for the samples from JAP1 and AMA1 under triaxial conditions.The soil behavior under shearing is easily observed in the effective stress paths shown in these figures.Peak friction angles between 34 • and 38 • were estimated in triaxial compression for these two borehole samples.The secant friction angle, Ø′sec, was estimated for axial strains greater than 12%.Average friction angles of 35° (specimens from depths of 3.50 m to 7.50 m) and 38° (specimens from depths of 9.00 m to 14.50 m) constitute the post-peak response of samples from JAP1 and AMA1.This relationship between Ø′sec and sample depth, however, is not definitive, given that some factors (such as particle shape, size distribution and configuration, grain mineralogy, void ratio, water content, and previous stress history) can affect the soil strength measured in a lab test [72].
Figure 18 shows the stress paths in the q-p′ plane for the samples from JAP1 and AMA1 under triaxial conditions.The soil behavior under shearing is easily observed in the effective stress paths shown in these figures.Peak friction angles between 34° and 38° were estimated in triaxial compression for these two borehole samples.A summary of the strength parameters obtained from the consolidated-undrained (CU) triaxial compression tests from JAP1 and AMA1 is provided in Table 1.The shallow specimens show a peak friction angle of Ø peak ≈ 35 • and an effective cohesion (c') between 5 kPa and 26 kPa, whereas the deep samples show a peak friction angle of Ø peak ≈ 38 • and an effective cohesion (c ) between 10 kPa and 20 kPa.The studied soils have friction angle (Ø ) values that are slightly lower and cohesion values (c') that are much lower than those of the volcanic soils analyzed by O'Rourke and Crespo [2].This is justified to a certain degree, given that they are similar in structure, although from a different formation.The soils examined by O'Rourke and Crespo [2] were in an area between the sectors of Tumbaco and the Chillos Valley, to the east of Quito, while those in the present study are from the north-central region of the city.
Figure 19a shows the variation profile of the peak friction angle (Ø peak ) with depth for boreholes JAP1 and AMA1 according to the values given in Table 1.The tendency of the friction angle value to increase with depth can be clearly seen.It can also be seen that the Standard Penetration Test values (N SPT ) were correlated with the friction angle (Ø'), after which the linear regression analysis technique was adopted to obtain this relationship.Finally, the relationship with the best fit achieved in this process is shown in Figure 19b and Equation (8).Ø = 0.185 N SPT + 32.50 (8) Sustainability 2023, 15, x FOR PEER REVIEW 19 of 32 A summary of the strength parameters obtained from the consolidated-undrained (CU) triaxial compression tests from JAP1 and AMA1 is provided in Table 1.The shallow specimens show a peak friction angle of Ø′peak ≈ 35° and an effective cohesion (c') between 5 kPa and 26 kPa, whereas the deep samples show a peak friction angle of Ø′peak ≈ 38° and an effective cohesion (c′) between 10 kPa and 20 kPa.The studied soils have friction angle (Ø′) values that are slightly lower and cohesion values (c') that are much lower than those of the volcanic soils analyzed by O'Rourke and Crespo [2].This is justified to a certain degree, given that they are similar in structure, although from a different formation.The soils examined by O'Rourke and Crespo [2] were in an area between the sectors of Tumbaco and the Chillos Valley, to the east of Quito, while those in the present study are from the north-central region of the city.
Figure 19a shows the variation profile of the peak friction angle (Ø′peak) with depth for boreholes JAP1 and AMA1 according to the values given in Table 1.The tendency of the friction angle value to increase with depth can be clearly seen.It can also be seen that the Standard Penetration Test values (NSPT) were correlated with the friction angle (Ø'), after which the linear regression analysis technique was adopted to obtain this relationship.Finally, the relationship with the best fit achieved in this process is shown in Figure 19b and Equation (8).

Drained Shear Strength Properties
The drained strength of the soil is represented by the parameters of effective cohesion (c ) and the effective friction angle (Ø ) and is used for long-term analysis.As part of this research, consolidated-drained (CD) triaxial tests with volume change measurements were also performed on 38 mm diameter and 76 mm height specimens per ASTM D7181 specification [73] recommendations.In this type of triaxial test, during the compression rupture phase of the specimen, the external pressure of the cell is kept constant, and the free drainage of the sample is left at a constant strain rate.
Each triaxial test comprised three successive stages: (1) saturation, (2) consolidation, and (3) rupture under drained conditions.The saturation stage of each specimen was carried out for 24 h, and at the end of the stage, it was verified that Skempton's B parameter was greater than 0.96.The consolidation stage was carried out under isotropic conditions, with pore water drainage at the top of the specimen.Finally, the rupture stage was performed under drained conditions and with a vertical displacement velocity of 0.01 mm/min.
Figure 20 shows the axial unitary stress-strain curves, q-ε s , with the variation in the volume change for each of the samples from boreholes JAP1 and AMA1.

Drained Shear Strength Properties
The drained strength of the soil is represented by the parameters of effective cohesion (c′) and the effective friction angle (Ø′) and is used for long-term analysis.As part of this research, consolidated-drained (CD) triaxial tests with volume change measurements were also performed on 38 mm diameter and 76 mm height specimens per ASTM D7181 specification [73] recommendations.In this type of triaxial test, during the compression rupture phase of the specimen, the external pressure of the cell is kept constant, and the free drainage of the sample is left at a constant strain rate.
Each triaxial test comprised three successive stages: (1) saturation, (2) consolidation, and (3) rupture under drained conditions.The saturation stage of each specimen was carried out for 24 h, and at the end of the stage, it was verified that Skempton's B parameter was greater than 0.96.The consolidation stage was carried out under isotropic conditions, with pore water drainage at the top of the specimen.Finally, the rupture stage was performed under drained conditions and with a vertical displacement velocity of 0.01 mm/min.
Figure 20 shows the axial unitary stress-strain curves, q-εs, with the variation in the volume change for each of the samples from boreholes JAP1 and AMA1.A summary of the strength parameters obtained from consolidated-drained triaxial compression (CD) tests of JAP1 and AMA1 specimens is presented in Table 2.The tests performed show a peak friction angle of Ø′peak ≈ 37° and an effective cohesion (c′) between 20 kPa and 69 kPa.A summary of the strength parameters obtained from consolidated-drained triaxial compression (CD) tests of JAP1 and AMA1 specimens is presented in Table 2.The tests performed show a peak friction angle of Ø peak ≈ 37 • and an effective cohesion (c ) between 20 kPa and 69 kPa.

Deformation Parameters
The basic deformation parameters can be derived from the stress-strain curves, q-ε s .In this way, the drained, E i , and undrained, E ui , moduli of elasticity and the secant modulus at 50% of the failure stress, E 50 , can be obtained.Duncan and Chang [74] introduced a failure stress ratio of R f = (σ 1 − σ 3 ) f /(σ 1 − σ 3 ) ult , because (σ 1 − σ 3 ) f is generally less than (σ 1 − σ 3 ) ult , where (σ 1 − σ 3 ) f is the deviatoric stress at failure, and (σ 1 − σ 3 ) ult is the last asymptotic value of the deviatoric stress in the triaxial test.
The relationship between these different parameters can be seen in Plaxis [46].By way of example, the parameter E 50 is the confining stress-dependent stiffness modulus for primary loading and is obtained by Equation ( 9).
where E ref 50 is a reference secant stiffness modulus corresponding to the reference confining pressure p ref , and m is the stress dependence relationship in the stiffness behavior, while E ref i is the drained stiffness modulus at the reference pressure, and E ref ui is the undrained stiffness modulus at the reference pressure.
The deformation parameters obtained from the stress paths for a reference pressure p ref of 100 kPa for the consolidated-undrained triaxial compression tests (CU) are given in Table 3, while Table 4 shows the deformation parameters for the triaxial compression tests (CD).

Discussion of the Geotechnical Characterization Study
This study's soil classification is consistent with the volcanic soil classifications of other researchers, as is the case with Hürlimann et al. [14], who worked with soils in Tenerife, Canary Islands (Spain), and mainly identified them as silty sands (SM); Crosta et al. [10], who investigated the volcanic soils of the Santa Tecla (El Salvador) zone and recognized the presence of low to high-plasticity silts (ML and MH), medium-plasticity clays (CL), and silty sands (SM); and Brandes and Nakayama [13], who studied the volcanic soils in the islands of Oahu and Hawaii (USA), which were identified as medium-to-high plasticity silts (ML and MH) and high-plasticity clays (CH) and silty sands (SM).
The presence of mainly plagioclases and pyroclastic materials of andesitic composition was identified through mineralogy and microstructure analyses; silica, a principal cementing agent, was also found to be present.
With regard to the parameters obtained from the oedometric tests, the C c soil values in this study (0.06-0.36) are similar to those determined by Hürlimann et al. [14] for the volcanic soils of Tenerife (Spain), where the value for this index was 0.287.Conversely, the C c value range of this survey is similar to the C c value of 0.22 obtained for volcanic soils identified as medium-plasticity red silt (ML) from Kapolei, Hawaii (USA), and much less than the C c value of 0.49 for the high-plasticity brown clay (CH) in this same zone obtained by Brandes and Nakayama [13].
In this study, in general, the Ø peak obtained shows a minimum value of 33.7 • at a depth of 3.5 m, gradually increasing with depth to 38.0 • at 14.5 m.Two separate groups are clearly identifiable.Between 3.5 m and 7.5 m, the measured Ø peak values range from 33.7 • to 34.8 • , with an average value of 35 • .At depths between 9 m and 14.5 m, the measured Ø peak values range from 37.1 • to 38.0 • , with an average value of 38 • .The friction angle values are slightly less than those of the volcanic soil values found by O'Rourke and Crespo [2] in the eastern zone of the city of Quito (Ecuador), which ranged between 39 • and 40 • , while the values obtained in this study are within the range for the Tenerife, Canary Islands (Spain), volcanic soils analyzed by Hürlimann et al. [14], which were between 30 • and 40 • .In the same manner, the friction angle values for this study are very similar to those of the volcanic soils studied in San Salvador (El Salvador) by Bommer et al. [9], which varied between 35 • and 40 • .Conversely, the Ø peak friction angle values for this study are similar to the value of 32.7 • determined for the red medium-plasticity silts in Kapolei, Hawaii (USA), and greater than the value of 23.4 • obtained from the brown high-plasticity clay in this same region studied by Brandes and Nakayama [13].
The cohesion values obtained in the present study (5 to 26 kPa) are very similar to those of the volcanic soils in San Salvador (El Salvador) investigated by Bommer et al. [9], which oscillated between 25 kPa and 30 kPa.Furthermore, the values obtained in this study are seen to be within the range of the volcanic soils from Isparta (Turkey) studied by Avşar et al. [16], which ranged between 0 and 52 kPa, as can be seen in Table 5.The cohesion values of the volcanic soils in Java (Indonesia) derived from the weathering of volcanic deposits and volcanic ash were determined by Wesley [75] to be between 13 kPa to 14 kPa, which fits within the range of the values obtained in this study.The studied structure is named the Zaigen Building and is located in the north-central area of the city of Quito, precisely in the JAP1 drilling area.It has five underground car park levels and a total excavation of 15.50 m, achieved by means of five partial excavations (h = 3.10 m) that represent the height of a basement level, as shown in Figure 21.In this numerical model, using the finite element method with Plaxis 2D [44][45][46], a small surface overload of 1 kN/m has been included in the roadway to consider the light and sporadic vehicular traffic during the construction process.Figure 21a presents the initial numerical model for the Soil Nailing structure, including dimensions, structural elements, and other parameters that characterize this structure.Figure 21b shows the numerical model in the fifth phase of excavation, which is when underground level 5 had already been built and a total excavation of 15.50 m had been completed.Additionally, the construction of each basement level includes four basic construction phases: (1) the initial excavation of the entire basement level (h = 3.10 m), leaving a small soil buttress, (2) the construction of the Soil Nail, (3) the vertical shaping of the slope, and (4) the construction of the concrete facing.

Structure Characteristics
The studied structure is named the Zaigen Building and is located in the north-central area of the city of Quito, precisely in the JAP1 drilling area.It has five underground car park levels and a total excavation of 15.50 m, achieved by means of five partial excavations (h = 3.10 m) that represent the height of a basement level, as shown in Figure 21.In this numerical model, using the finite element method with Plaxis 2D [44][45][46], a small surface overload of 1 kN/m has been included in the roadway to consider the light and sporadic vehicular traffic during the construction process.Figure 21a presents the initial numerical model for the Soil Nailing structure, including dimensions, structural elements, and other parameters that characterize this structure.Figure 21b shows the numerical model in the fifth phase of excavation, which is when underground level 5 had already been built and a total excavation of 15.50 m had been completed.Additionally, the construction of each basement level includes four basic construction phases: (1) the initial excavation of the entire basement level (h = 3.10 m), leaving a small soil buttress, (2) the construction of the Soil Nail, (3) the vertical shaping of the slope, and (4) the construction of the concrete facing.To generate a finite element mesh with an appropriate density, 15-node elements were used.A "very fine" element mesh was generated to obtain accurate numerical results.The initial stresses for the model taking the loading history of the soils into account were generated using the K0 procedure.Furthermore, standard interfaces in the Soil Nails have been included in the model to consider and simulate the existing friction in the soil-anchor interaction [45].The value considered for the strength of the interfaces was Rinter = 0.67.

Geotechnical Parameters
The geotechnical characterization study determined that the project area's subsoil consists of volcanic soils containing mainly silts and clays with low-to-high plasticity and silty sands.Two main soil strata were identified (0-7.5 m and 7.5-15.5 m), for which the respective geotechnical parameters were determined.Soil strength parameters were To generate a finite element mesh with an appropriate density, 15-node elements were used.A "very fine" element mesh was generated to obtain accurate numerical results.The initial stresses for the model taking the loading history of the soils into account were generated using the K 0 procedure.Furthermore, standard interfaces in the Soil Nails have been included in the model to consider and simulate the existing friction in the soil-anchor interaction [45].The value considered for the strength of the interfaces was R inter = 0.67.

Geotechnical Parameters
The geotechnical characterization study determined that the project area's subsoil consists of volcanic soils containing mainly silts and clays with low-to-high plasticity and silty sands.Two main soil strata were identified (0-7.5 m and 7.5-15.5 m), for which the respective geotechnical parameters were determined.Soil strength parameters were determined through CU and CD triaxial testing, while the stiffness parameters were determined exclusively through CD triaxial testing.Table 6 shows the parameters determined for the application of the Mohr-Coulomb (MC) soil constitutive model.Table 7 shows the parameters for the Hardening Soil (HS) constitutive model.The application of the Hardening Soil with Small-Strain Stiffness (HSsmall) soil constitutive model requires the same parameters as the Hardening Soil model and also the additional parameters presented in Table 8 [46].

Characteristics of the Facing and Soil Nails
Tables 9 and 10 show the parameters of axial stiffness EA, flexural rigidity EI, and unit weight w for the facing and the Soil Nails.The parameters for the facing were calculated for a unit length of 1 m and for a concrete unit weight of 24 kN/m 3 .In order to obtain the Soil Nail parameters, an equivalent modulus of elasticity was initially determined considering the cross-section composed of steel and grout, and then the stiffness values were obtained for each row as a function of the horizontal spacing of the Soil Nails, as shown in Table 10. Figure 22 presents the analysis of the structure for the construction of basement 5.
The construction of basement level 5 produced a total height of 15.5 m on the facing.It is therefore the construction phase associated with the greatest degree of displacements and stresses.It is clear from the analysis with the three constitutive soil models that excavation with the Mohr-Coulomb (MC) model presents very high soil uplift values at the bottom of the excavation, which is a situation that is not realistic, in contrast to the analysis with the HSsmall model, which determined low soil uplift values at the bottom of the excavation and is closer to reality.On the other hand, the Hardening Soil (HS) model presents uplift values in an intermediate range that falls between the analyses with MC and HSsmall, as can be seen in Figure 22.Figures 23 and 24 show the distribution of axial tension forces in the Soil Nails and the displacements induced by the construction of basement level 5, respectively.The construction of basement level 5 produced a total height of 15.5 m on the therefore the construction phase associated with the greatest degree of displac stresses.It is clear from the analysis with the three constitutive soil models that with the Mohr-Coulomb (MC) model presents very high soil uplift values at the b excavation, which is a situation that is not realistic, in contrast to the analysis with model, which determined low soil uplift values at the bottom of the excavation a to reality.On the other hand, the Hardening Soil (HS) model presents uplift valu termediate range that falls between the analyses with MC and HSsmall, as can be ure 22. Figures 23 and 24 show the distribution of axial tension forces in the Soil N displacements induced by the construction of basement level 5, respectively.The tensile force magnitudes determined for the Soil Nails with the Mohr-Coulo constitutive model are generally lower than the stresses determined with the Harden Soil and HSsmall models.However, the forces obtained with Hardening Soil and HSs have some similarities between them for most of the process, with the Hardening stresses being slightly higher in most of the construction phases, as can be seen in Fig 23 .Accurately estimating the maximum tensile strength that a Soil Nail can sus throughout its service life is a crucial aspect of the final design of a Soil Nailing struct This step considers the ultimate limit states of the pullout and tensile strength of the Nails [76].Achieving precision in estimating the pullout capacity of a Soil Nail is essen to ensure a cost-effective, efficient, and safe design [77,78].Therefore, it underscores importance of adopting an appropriate soil constitutive model for the geotechnical a ysis of a Soil Nailing structure.
For most of the construction stages, the horizontal facing displacements determ with the Mohr-Coulomb model are the lowest, unlike the horizontal displacements tained with Hardening Soil, which are greater than the rest, while the values with HSs remain in an intermediary position.
Vertical displacements or settlements of the soil behind the facing, as determ with the Mohr-Coulomb model resulted mainly in states of soil rising or uplift rather t settlements, because this constitutive soil model uses a single modulus of soil elast for loading and unloading.On the other hand, the analyses of vertical displacements w the Hardening Soil and HSsmall soil constitutive models both determined similar va of settlements induced by the construction of the basement levels, with the Hardening settlements being slightly higher.The settlements obtained with these two constitu soil models are expected to be more realistic, since they additionally include an unlo ing/reloading stiffness modulus, Eur, which allows for the representation of the beha of the soil under loading and unloading conditions.
Figure 25 and Table 11 present the Factor of safety (FoS) variation during the struction progress of each basement level.A comparison of the three different constitu soil model analyses was made through the finite element method with Plaxis 2D [44 and different limit equilibrium methods with Slide2 [79].The tensile force magnitudes determined for the Soil Nails with the Mohr-Coulomb constitutive model are generally lower than the stresses determined with the Hardening Soil and HSsmall models.However, the forces obtained with Hardening Soil and HSsmall have some similarities between them for most of the process, with the Hardening Soil stresses being slightly higher in most of the construction phases, as can be seen in Figure 23.Accurately estimating the maximum tensile strength that a Soil Nail can sustain throughout its service life is a crucial aspect of the final design of a Soil Nailing structure.This step considers the ultimate limit states of the pullout and tensile strength of the Soil Nails [76].Achieving precision in estimating the pullout capacity of a Soil Nail is essential to ensure a cost-effective, efficient, and safe design [77,78].Therefore, it underscores the importance of adopting an appropriate soil constitutive model for the geotechnical analysis of a Soil Nailing structure.
For most of the construction stages, the horizontal facing displacements determined with the Mohr-Coulomb model are the lowest, unlike the horizontal displacements obtained with Hardening Soil, which are greater than the rest, while the values with HSsmall remain in an intermediary position.
Vertical displacements or settlements of the soil behind the facing, as determined with the Mohr-Coulomb model resulted mainly in states of soil rising or uplift rather than settlements, because this constitutive soil model uses a single modulus of soil elasticity for loading and unloading.On the other hand, the analyses of vertical displacements with the Hardening Soil and HSsmall soil constitutive models both determined similar values of settlements induced by the construction of the basement levels, with the Hardening Soil settlements being slightly higher.The settlements obtained with these two constitutive soil models are expected to be more realistic, since they additionally include an unloading/reloading stiffness modulus, E ur , which allows for the representation of the behavior of the soil under loading and unloading conditions.
Figure 25 and Table 11 present the Factor of safety (FoS) variation during the construction progress of each basement level.A comparison of the three different constitutive soil model analyses was made through the finite element method with Plaxis 2D [44,45] and different limit equilibrium methods with Slide2 [79].Both methodologies provided a satisfactory analysis of the nailed facing stability.However, the FoS determined with finite elements and limit equilibrium presented disparate values at the beginning of the basement-level construction; however, these values converged as the construction progressed, eventually arriving at similar values at the end of the construction of the fifth basement level, with similar potential failure surfaces.

Conclusions
Geotechnical characterization studies are fundamental in the evaluation and analysis of landslides, particularly in urban environments, where significant stabilization works are undertaken as ground reinforcement.Precise knowledge of the geotechnical properties of the materials within an earth structure is useful to comprehend its failure mechanism and determine the appropriate geological model, allowing for the selection of the most suitable soil constitutive model to accurately represent the actual conditions.
In this study, we took an application-based approach to Soil Nailing structures, which are frequently used in reinforcing excavations for the construction of underground basements in buildings in the city of Quito.This method has been technically used worldwide, but in many cases in the Ecuadorian capital, it is still applied in a traditional and artisanal manner.Globally, the technique has been used in different soil types, but it is not easy to find specific studies for this type of structure in volcanic soils.Both methodologies provided a satisfactory analysis of the nailed facing stability.However, the FoS determined with finite elements and limit equilibrium presented disparate values at the beginning of the basement-level construction; however, these values converged as the construction progressed, eventually arriving at similar values at the end of the construction of the fifth basement level, with similar potential failure surfaces.

Conclusions
Geotechnical characterization studies are fundamental in the evaluation and analysis of landslides, particularly in urban environments, where significant stabilization works are undertaken as ground reinforcement.Precise knowledge of the geotechnical properties of the materials within an earth structure is useful to comprehend its failure mechanism and determine the appropriate geological model, allowing for the selection of the most suitable soil constitutive model to accurately represent the actual conditions.
In this study, we took an application-based approach to Soil Nailing structures, which are frequently used in reinforcing excavations for the construction of underground basements in buildings in the city of Quito.This method has been technically used worldwide, but in many cases in the Ecuadorian capital, it is still applied in a traditional and artisanal manner.Globally, the technique has been used in different soil types, but it is not easy to find specific studies for this type of structure in volcanic soils.
The Soil Nailing structure presented herein was analyzed with advanced soil constitutive models using the finite element method.The main advantage of an analysis using the finite element method is a detailed analysis of soil deformations, unlike limit equilibrium methods, which do not permit this type of analysis.
The HSsmall and Hardening Soil constitutive soil models better reproduced the behavior of Soil Nailing structures; however, their application requires specialized testing, such as CU and CD triaxial tests, which are necessary to determine the shear strength parameters, with the additional consideration that CD triaxial testing is mandatory to determine stiffness parameters.Furthermore, oedometric testing is necessary for the application of these soil models to obtain the tangent stiffness moduli.This study included, among others, all of the previously mentioned tests.
Finally, the area of study is generally characterized by volcanic soils with high void ratios and porosity resulting from the natural presence of gas bubbles in their microstructures.In such soils, initial shear strength parameters are identified that greatly favor the stability of cut slopes generated by human activity.However, earth structures consisting of such materials that are not equipped with an adequate protection or lining system to safeguard against external agents, particularly rain, could experience a sudden and accelerated reduction in their shear strength characteristics if microscopic gas bubbles are filled with water, causing the main structure to collapse.
In summary, comprehensive geotechnical characterization studies will allow for determining parameters to reproduce the geological conditions of a specific area through a coherent theoretical model, aimed at analyzing its stability and successfully preventing landslides.Moreover, an understanding of these soils in terms of their behavior and potential failure mechanism means that recommendations can be made concerning the best type of reinforcement and stabilization systems for earth structures developed in a particular area, with an emphasis on urban environments.

Figure 1 .
Figure 1.Map of Ecuador showing Quito, its capital, and the La Carolina sector.

Figure 1 .
Figure 1.Map of Ecuador showing Quito, its capital, and the La Carolina sector.

Figure 2 .
Figure 2. Locations of the three boreholes.

Figure 2 .
Figure 2. Locations of the three boreholes.
15,  x FOR PEER REVIEW 6 of 32 deposition sequence and generally consists of materials of varied granulometric size, including gravel and boulders.

Figure 6 shows
Figure6shows Casagrande plasticity charts for samples from boreholes JAP1, AMA1, and AUS1.It is evident that all the samples lie close to the A-line.Most of those from JAP1 are classified as silts and clays with low-to-high plasticity, while most from AMA1 and AUS1 are silts and clays with low-to-intermediate plasticity.

Figure 6 shows 32 Figure 5 .
Figure6shows Casagrande plasticity charts for samples from boreholes JAP1, AMA1, and AUS1.It is evident that all the samples lie close to the A-line.Most of those from JAP1 are classified as silts and clays with low-to-high plasticity, while most from AMA1 and AUS1 are silts and clays with low-to-intermediate plasticity.

Figure
Figure 9b shows the porosity values, which were found to range between 47% and 66% in JAP1 and between 33% and 50% in AMA1.Likewise, the studied soils have high porosity values, in agreement with the volcanic soil studies by O'Rourke and Crespo [2], Hürlimann et al. [14], Bommer et al. [9], and Avşar et al. [16].

Figure 9 .
Figure 9. (a) Void ratio versus depth; (b) porosity versus depth for boreholes JAP1 and AM

Figure 13 .
Figure 13.One-dimensional compression oedometer tests of samples from JAP1 and AMA1.For the JAP1 borehole, the compression index (Cc) sample values range between 0.15 and 0.36, and the swelling index (Cs) values are in the range of 0.02 to 0.05.AMA1 has Cc values between 0.06 and 0.30 and Cs values between 0.01 and 0.02.Figure14ashows the relationship between the compression index (Cc) and the natu-

Figure 14 .
Figure 14.Correlation between (a) compression index (C c ) and (b) swelling index (C s ) with the natural moisture content (w nat ) and liquid limit (LL); (c) correlation between compression (C c ) and swelling (C s ) indexes with Initial void ratios (e 0 ).Empirical formulas are obtained for the soil of the study area, according to Figure 14.C c = 0.0049 (w nat − 1.47) (1)

Figure 23 .
Figure 23.Distribution of axial tensile forces in Soil Nails induced by construction of basement level 5.

Figure 23 .Figure 24 .
Figure 23.Distribution of axial tensile forces in Soil Nails induced by construction of basement leve

Figure 25 .
Figure 25.Factor of safety (FoS) variations during the construction progress of basement levels: (a) finite element method; (b) limit equilibrium methods.

Figure 25 .
Figure 25.Factor of safety (FoS) variations during the construction progress of basement levels: (a) finite element method; (b) limit equilibrium methods.

Table 1 .
Undrained strength parameters for samples from boreholes JAP1 and AMA1.

Table 1 .
Undrained strength parameters for samples from boreholes JAP1 and AMA1.

Table 2 .
Drained shear strength parameters for borehole samples JAP1 and AMA1.

Table 2 .
Drained shear strength parameters for borehole samples JAP1 and AMA1.

Table 3 .
Deformation parameters of controlled stress paths of triaxial CU-type tests of JAP1 and AMA1 borehole samples.

Table 4 .
Deformation parameters of CD-type triaxial tests of JAP1 and AMA1 borehole samples.

Table 5 .
Comparison of the geotechnical properties with those of volcanic soils studied by other research groups.Modified Table from Avşar et al. [16].

Analysis of a Soil Nailing Structure Built in the Area of Study
4.1.Structure Characteristics [16]e taken from Avşar et al.'s[16]study.2Valuescalculated according to porosity values. 1

Table 7 .
Geotechnical parameters for the Hardening Soil (HS) constitutive model.

Table 8 .
Additional geotechnical parameters for HSsmall constitutive model.

Table 9 .
Geometric characteristics and other parameters of the Soil Nailing structure.

Table 10 .
Axial stiffness EA, flexural rigidity EI, and unit weight w of Soil Nails.

Table 11 .
Factor of safety (FoS) variations with basement-level construction progress.

Table 11 .
Factor of safety (FoS) variations with basement-level construction progress.