Life Cycle Assessment of the High Performance Discontinuous Fibre (HiPerDiF) Technology and Its Operation in Various Countries

: Composite waste is a growing issue due to the increased global demand for products manufactured from these advanced engineering materials. Current reclamation methods produce short length ﬁbres that, if not realigned during remanufacture, result in low-value additives for non-structural applications. Consequently, to maximise the economic and functional potential, ﬁbre realignment must occur. The High Performance Discontinuous Fibre (HiPerDiF) technology is a novel process that produces highly aligned discontinuous ﬁbre-reinforced composites, which largely meet the structural performance of virgin ﬁbres, but to date, the environmental performance of the machine is yet to be quantiﬁed. This study assessed the environmental impacts of the operation of the machine using life cycle assessment methodology. Electrical energy consumption accounts for the majority of the greenhouse gas emissions, with water consumption as the main contributor to ecosystem quality damage. Suggestions have been made to reduce energy demand and reuse the water in order to reduce the overall environmental impact. The hypothetical operation of the machine across different European countries was also examined to understand the impacts associated with bulk material transport and electricity from different energy sources. It was observed that the environmental impact showed an inverse correlation with the increased use of renewable sources for electricity generation due to a reduction in air pollutants from fossil fuel combustion. The analysis also revealed that signiﬁcant reductions in environmental damage from material transport between the reclamation facility to the remanufacturing site should also be accounted for, and concluded that transportation routes predominantly via shipping have a lower environmental impact than road and rail haulage. This study is one of the ﬁrst attempts to evaluate the environmental impact of this new technology at early conceptual development and to assess how it would operate in a European scenario.


Introduction
Carbon fibre reinforced polymer (CFRP) composites have become increasingly popular in several areas of application due to their advantageous mechanical properties (e.g., high specific strength and stiffness) and desirable aesthetic characteristics. In particular, CFRP composites exhibit high specific performance, resistance to corrosion, and high durability [1]; all of which are being explored in earnest for high performing alternatives to conscious approach means that producers and consumers are increasingly turning to life cycle assessment (LCA) to analyse the EI of products and services. The successful inclusion of LCA is evident across high value manufacturing composite industries already, including marine [34], aerospace [35,36], construction [37][38][39][40], and wind energy [41,42]. This paper aims to evaluate the EI of the HiPerDiF technology through LCA, to highlight any environmental hotspots and identify pathways for technology optimisation. Further analyses have widened the system boundary to consider the practical logistics of operating the technology in various EU location scenarios, incorporating different sources of electrical energy and transportation routes.

The HiPerDiF Technology
The HiPerDiF method is a patented manufacturing process [43] to produce highly aligned discontinuous fibre tapes [25]. The third generation of the HiPerDiF machine, capable of high throughput (up to 100 m/hour quantities of prepreg) with full instrumentation, has been constructed at the National Composites Centre (NCC) in Bristol, funded by the Engineering and Physical Sciences Research Council (EPSRC) [27,44] [27]. The focus of this study is on the previous laboratory-scale machine (HiPerDiF 2G), built as a proof of concept for research and development purposes, shown schematically in Figure 1. At the start of the process, discontinuous fibres of between 1 and 15 mm in length are suspended in a low viscosity aqueous carrier fluid [46]. With the aid of the peristaltic pump, this suspension is accelerated and directed through a series of nozzles towards a course of narrowly spaced parallel plates, demonstrated in Figure 1a. The alignment mechanism relies on a sudden liquid momentum change upon impact with the plates [47,48]. The aligned fibres are subsequently carried along a conveyor belt whilst the water medium is removed by vacuum suction and the fibre preform is dried via infrared heater (see Figure 1b). The result is a dry fibre preform-tape ready for impregnation with resin ( Figure 1c). A recovery system allows the machine to recirculate and reuse part of the carrier fluid. Other than the reclaimed material and the polymer film that constitutes the new matrix, the HiPerDiF system only requires electrical energy and water as inputs.
The HiPerDiF technology has been used to remanufacture carbon fibres reclaimed both with pyrolytic and solvolytic processes [26,28], as well as manufacturing waste [32], into high performance recycled composites. Moreover, it was used to intermingle rCF and natural fibres to obtain functionalised materials with potential vibration damping applications [27]. The mechanical advantages of HiPerDiF technology for the remanufacture of reclaimed fibres are evident, with clear retention of preferred characteristics demonstrated: Longana et al. observed a 26% increase in stiffness and 77% increase in strength for a quasi-isotropic composite made from HiPerDiF aligned tape preforms from randomly orientated composite [45].

Life Cycle Assessment of FRP Material
LCA is a structured method using a holistic systems-based approach to identify the environmental hotspots through a product's life cycle, from the raw material extraction and product assembly through to its use and EOL disposal options. A four-phase framework to complete an LCA is collated into a set of International Standard Organisation rules [49,50], which maintain enough flexibility to allow its application to any product or process. These are: 1.
Goal and scope definition: establishing the reason for the study and defining the system under review. Whilst LCAs are based on qualified scientific data, they can have subjective elements, for example, the chosen system boundary, functional unit, or underlying assumptions, which must all be declared before carrying out the data collection phase.

2.
Inventory analysis: an inventory collates the inputs, outputs, and other environmental aspects within the system boundary for the functional unit. Figure 2 represents a schematic of a composite material product LCA, with materials and energy as inputs and waste materials and emissions as the outputs, collected during the inventory analysis stage for a cradle-to-grave system.

3.
Impact assessment: the inventory data are weighted and characterised to show the impacts on natural resources, the environment, and human health.

4.
Interpretation: results are analysed. To ensure meaningful conclusions from LCA, a critical approach to interpreting the results is achieved through a series of checks throughout the assessment. LCA manages a large amount of complex data and is designed to clearly communicate this information to a wide audience. The holistic system approach avoids shifting the problem from one life cycle impact stage to another or across EIs [52]. There are also limitations, such as time and resources required for completion, along with the subjective choice of assumptions and system boundary upon which the LCA has been based. It is therefore crucial that plenty of time is factored in to undertake the study, and the approach taken is well documented for transparency.
Until recently, applications for recovered fibres from waste composite have been limited, and therefore LCA data for recycling and remanufacturing of composites are rarely available [53]. Previous studies have highlighted the ecological need to develop recycling routes for composites, and have also underlined how the benefits of recycling are strongly linked to the impacts of the reclamation process, the materials replaced by rCF in the second-life application, and the type of application in which they are used [54]. The onward use or second life cycle of recycled composites is not often considered in LCA and there is uncertainty surrounding the retention of the mechanical properties of the composite through the various recycling processes, especially without fibre realignment. Virgin material may still be required to compensate if the recyclate quality is compromised. Assuming performance equivalency between virgin and recycled CFRP material, Tapper et al. concluded that the additional environmental burden from producing and manufacturing CFRP automotive parts compared to a steel baseline does not break even until recycled materials are used, despite the significant environmental savings reported during the use phase [51]. Therefore, the closer the resulting quality of the remanufactured composite is to the original virgin architecture and material performance, the less virgin fibre material is required to compensate, which will bring significant environmental and economic savings to the automotive industry-one of the aims of HiPerDiF technology.
The inclusion of HiPerDiF technology could result in recycled composites that retain the preferred mechanical properties associated with virgin material, displacing the production of composites from raw material extraction. There are currently no published studies on the EI of fibre realignment methods, so the results from this LCA will be the first of its kind. This will limit the ability to include direct comparisons within the analysis and further highlight the large gap of research into other fibre remanufacturing technologies.

Goal and Scope Definition
The present work is a gate-to-gate study to assess the EI associated with the realignment of discontinuous fibres using the HiPerDiF 2G machine. This will focus purely on the process energy demand (PED) of machine operation and exclude the embodied energy that is required to build the machine or from the aligned output material. The LCA is divided into three distinct sections:

1.
Inventory assessment with primary data collection of the PED of appliances used and water required for HiPerDiF technology operation in Bristol, UK. A schematic of the system boundary is presented in Figure 3, indicating the flow of energy through the HiPerDiF prototype during processing. The only inputs to this system that will contribute to the environmental burden are the electrical energy and the water required to run the machine. These data will be used to identify hotspots for future optimisation and will form the baseline against which further impact assessment analyses can be compared. The functional unit (FU) is a quantitative measure of the output of a product or service from the system under investigation [55]. A mass-based FU was selected over a specific composite component so this study can benefit from comparison with future work, which will be the throughput of 1 gramme of aligned discontinuous fibre preform (ADFP).

2.
Impact assessment of HiPerDiF machine when operated in various EU location scenarios, specifically chosen to investigate the variability of impact across different sources of electricity generation, which are listed in Table 1. The following locations have been selected: a. Bristol, UK-the location of the current HiPerDiF 2G machine, acting as the control for comparison with the other scenarios. b.
Varberg, Sweden (SE)-the CFRP composite manufacturer Carbon & Composites AB [56] is situated on the west coast, south of Gothenburg. Sweden is one of the leading countries in Europe for electricity generated from renewable sources and between 2014 and 2017 65% of its net generating capacity per annum came from renewable sources [57]. c.
Zurich, Switzerland (CH)-Swiss electricity generation also comes predominantly from renewable sources, at 77% of total net generation capacity. However, Switzerland incorporates a vastly different wastewater management system than Sweden, discussed later in the paper. d.
Stade, Germany (DE)-Germany has a similar energy generation mix to the UK, predominantly from fossil fuels, but is further along in the transition towards renewably sourced electricity. It has the largest net generation capacity in solar and wind energy at 20% and 23% of the total, respectively, whereas Sweden and Switzerland source their electricity principally from hydroelectric power (HEP). Hexcel Composites GmbH [58] have a manufacturing site in Stade, conveniently located alongside the River Elbe connecting the North Sea with Hamburg harbour. The CU Nord Recycling Centre [59] is also located in Stade, indicating that if the HiPerDiF 2G machine were to be located in that region there would be few burdens associated with material transportation from the reclamation site.
e. Roussillon, France (FR)-72% of France's total electricity generation was sourced from nuclear power in 2017 [57]; France has the largest dependence on nuclear energy in the world. Opened in 2018, the Hexcel Roussillon [60] plant is their main production site for polyacrylonitrile (PAN), the carbon fibre precursor, and CF for aerospace CFRP composites. The transportation distances for each route were calculated using Google Maps and typical sea routes between nearby industrial ports with SeaRoutes.com [63]. Most of the transport scenarios via sea also require road transport between the company site/destination and the port. For example, to transport recovered fibres from ELG (UK) to Roussillon (FR) the material would be transported by road from Birmingham to Dover, crossing the English Channel by freight ship to Dunkirk and finally reaching Roussillon by road. The purpose of this analysis is to understand the additional EI of transporting material to a location that has a lower operational EI due to a cleaner electricity source and wastewater treatment profile since it has often been cited in the academic literature that the transportation impact can contribute up to 50% of the entire recycling impact [5].
The impact assessments were carried out using SimaPro v9, a leading LCA software tool that incorporates data from the Ecoinvent 3 database. The impact assessment method IMPACT 2002+ was chosen for this study as it enables the impacts to be observed at 15 midpoint categories and then further aggregated into four damage endpoints: human health (HH), ecosystem quality (EQ), climate change (CC), and resources (Re) [64]. By characterising the data in this way, a causational link is established between the action and the effect. Respiratory effects, ionising radiation, human toxicity, and ozone layer depletion affect human health and are aggregated into the damage category HH, measured in disability-adjusted life years, known as DALY. This metric is used to quantify the burden of human disease resulting from environmental pollution and attributed to the life cycle of a system or product. Impacts to aquatic and terrestrial ecosystems which include acidification and eutrophication are grouped into EQ and are measured in PDF/m 2 /year, otherwise known as the potentially disappeared fraction of species per m 2 per year [65]. All emissions contributing to global warming are in the CC damage category and measured in kilogrammes of carbon dioxide equivalent (kg CO 2eq ). The total impacts associated with non-renewable energy consumption and mineral extraction are represented in the Re damage category and expressed as primary megajoules (MJ), measuring the surplus energy required to extract the equivalent non-renewable energy source utilised for the process and the total energy loss as a resource [66]. IMPACT 2002+ is the only method that offers all the available steps in LCIA: characterisation, damage assessment, normalisation, weighting, and single score addition which facilitates a more transparent communication of the results. Cumulative energy demand (CED) [67] is a single-issue impact assessment methodology used for the additional analysis of the transportation scenario as it allows a clearer observation of the emissions from different types of energy associated with transportation, expressed in MJ.

Inventory Analysis
To understand the EI of the HiPerDiF process, the inventory data were collected by measuring the electrical energy for each appliance, the water required to operate the machine and the mass of the fibre tape produced.
The energy demand data for each appliance was collected using a Watt meter and the water demand was measured with markings on the suspension tanks. The infrared heater and pumps required a different method of data collection because their power demand was not constant. For the heater, a connected thermocouple was set to maintain a temperature of 75 • C to prevent the heater from alternating between a ramp and dwell state. For the pumps, the inconsistent power reading could be caused by the fluctuating torque generated by the motor-the metal bars used to contract and relax the pipes lead to cyclic loading, which could also vary the resistance of the motor. To account for these variations, the machine was left to run for upwards of an hour so that the appliances were able to reach their regular operating temperatures. An average wattage was calculated by measuring the cumulative energy. Moreover, to produce 1 gramme of ADFP, 18.45 litres of water are required. The energy demand to manufacture 1 gramme of dry ADFP with the current HiPerDiF 2G process is summarised in Table 2. In terms of energy consumption, Table 2 shows vacuum suction is the appliance with the highest energy demand at 64% of the total power demand by HiPerDiF 2G. Next comes the second peristaltic pump for fibre realignment consuming only 19% of the power demand of the vacuum. This large difference highlights the dominance of the vacuum suction's energy demand over the other appliances, representing the area of greatest potential for optimisation.
Prior to this LCA, it was hypothesised that the infrared heater would consume the most energy since there is currently no insulation to prevent heat energy loss. The results in Table 2 show the infrared heater is the fourth largest power consumer. Notwithstanding, improvements to the efficiency of the drying phase is still considered to be one of the simplest options for machine optimisation, e.g., the addition of insulation would result in lower power consumption from the heater allowing it to spend longer periods in dwell state. Figure 4 demonstrates that that vacuum has a significantly higher impact in three of the four categories-HH, CC, and Re. Wastewater dominates the EQ category, which was anticipated due to the limited water reuse in the current prototype after it is collected from the vacuum. EIs associated with wastewater treatment in Europe in the Ecoinvent database are due to construction materials of the sewer grid and treatment facility (e.g., reinforcing steel, and chromium steel), as well as sludge activation and water purification, potentially toxic to aquatic and terrestrial life [68]. Two solutions can be found to reduce environmental burdens associated with water use/waste:

1.
Increase the fibre concentration of the machine such that more aligned fibre preform is manufactured per unit volume of water, and/or 2.
Adapt the design of the water reclamation process by pumping water back into the high concentration tank and reusing it for the next cycle. This could potentially cause instability in the fibre concentration in the tanks, resulting in an inconsistent fibre volume fraction of the final preform, and is a limitation of the design in this HiPerDiF 2G prototype. For the subsequent model (the HiPerDiF 3G based in NCC), the pumped water could be harvested into a separate storage tank for reuse in the next cycle.

Impact Assessment of HiPerDiF Operation in Various European Scenarios
This analysis compares the operation of HiPerDiF 2G in the five selected European countries (including water use), and a CED analysis of electricity energy sources used in each country of the sample group, presented in Figure 5. These LCIA results show that running the HiPerDiF 2G machine in the UK has the highest impact across all the categories except for Re. This is because the UK generates most of their energy from fossil fuels. Despite efforts to reduce GHG missions under the Climate Change Act 2008 [69], natural gas still dominates electricity production providing 40% of the total energy mix in 2017 [70]. Natural gas has an overall efficiency of over 80% energy from source making it one of the lowest overall impact fossil fuels [71], but it still requires the combustion of fossil fuel resources. The air pollutants from natural gas combustion are CO 2 , SO 2 , NO x and particulates, all of which affect the HH impact category through respiratory problems [72]. CO 2 is a GHG contributing to ozone layer depletion affecting the CC category, whereas other compounds such as SO x and NO x cause additional impacts in acidic deposition and eutrophication affecting the EQ category [73]. For electrical energy consumption only, the CED impact assessment was also chosen to analyse the energy sources used by each country, displayed in Figure 6. The CED method splits biomass into renewable (organic waste including wood and food products) and non-renewable (wood and biomass from primary forests) sources. The UK's largest power station, Drax, produces energy from both coal and biomass [74]; Figure 7 shows that the UK has the largest renewable biomass generation, contributing 40% of the national CED for renewable energy generation. The emission profile of burning biomass for energy is similar to that of natural gas, but lower impact than the burning of oil or coal. If the carbon sequestered by the plants through photosynthesis during their growth is accounted for in the biomass metric, then the net GHG emissions could be neutral [75]. However non-renewable biomass exhausts valuable primary forest resources whereas renewable biomass does not, reflected in a lower impact score for the Re category. This is still significantly overshadowed by the immense use of fossil fuels resulting in the UK performing the worst for the operation of the HiPerDiF 2G machine.  . CED assessment to remanufacture 1 kg of ADFP through HiPerDiF 2G in the various European scenarios (excluding water), presented as the impact relative to the renewable/non-renewable groups' highest value.
Germany (DE) is the second-largest user of fossil fuels in this study sample, as reflected by the second worst EI score in Figure 6, after the UK. The reasons for this are similar to those for the UK, but Germany still generates a large percentage of electricity from coal. GHG emissions from coal are higher than natural gas and oil due to the inefficiency of the combustion process. Coal-fired power plants have not yet benefitted from modernisation due to their planned gradual phase-out, and the emissions associated with burning coal contain pollutants with greater toxicity, such as CO x , SO x , soot, and other organic compounds [72]. Despite Germany using a more polluting fossil fuel base than the UK, it is still lower in all damage categories because it also receives the largest electricity generation from wind and solar sources in the sample group (Table 1). The EI of wind energy predominantly comes from the atmospheric emissions relating to the construction of the turbine, specifically the manufacture and assembly of the foundation (cement), and the structure itself (GFRP and CFRP composites, steel, and pig iron). Other EIs are noise from turbine operation [76] and the ecosystem impacts from wildlife interference (birds, shells, and fish) [77], but these are minimal compared to the impacts from using non-renewable energy sources. Similarly, with solar energy, the largest EI comes from the construction, installation and decommission phases [78]. During solar cell development, the manufacture of high technology materials, i.e., crystalline silicon and thin film, that maximise energy absorption efficiency result in high environmental burdens [79]. However, once the solar panel is in the use phase, no additional natural resources are exhausted and no waste products or emissions accumulate, giving an overall lower EI than for fossil fuels.
France (FR) has a significantly lower impact on HH than the UK and Germany ( Figure 5) despite generating most of its electricity from nuclear energy ( Figure 6). High environmental risks are associated with the extraction of uranium isotopes, the operation of the plants and the radioactive waste produced. The handling of radioactive material and the concentration of it in one place means that nuclear plants constantly emit low-level radiation to the surrounding area and therefore all life cycle stages of the nuclear fuel chain involve the emission of ionising radiation, posing the greatest risk for HH. LCA data from the literature [80] indicate the greatest risk to HH is associated with uranium mining, however, the system boundary for this work included the country's entire population for the sample. Academic literature has acknowledged an increased cancer rate in workers at nuclear energy plants [81,82] and, controversially, further studies have indicated an increased rate of cancer among populations surrounding nuclear plants [83]. If the largest risk lies with the minuscule proportion of the population who work and live around the plant/extraction site, the true impact on this group could be far greater than the results displayed in [80]. Figure 5 demonstrates that France also has the highest impact in the Re category because uranium isotopes are a non-renewable power source that must be extracted from rocks involving substantial mining efforts. Despite the detrimental effect this has on the surrounding ecosystem, a low amount of waste is produced relative to the amount of energy generated, most of which is stored at the plant, reflected by the moderate score for EQ damage. Whilst the degree of damage caused by low-level radiation on wildlife is significant, it is still not fully understood, with disagreement in academic opinion highlighting the need for further research [84,85]. Other EIs from nuclear energy are significantly less than fossil fuels overall since the reaction does not produce smoke or CO 2 [86]. EOL nuclear waste accumulation will become an increasing concern, and disposal options for low quantities of highly radioactive waste will likely affect EQ scores in the future [87].
Operating HiPerDiF 2G in Sweden (SE) has the lowest EI in all impact categories except EQ. SE generates the highest amount of electricity from renewable sources, accounting for 31% of the total CED (Figure 6), predominantly from HEP, representing 22% of the total and 71% of the contribution from renewables. In common with wind and solar power, there is no combustion during the generation of HEP, but dam locations can cause a chain of catastrophic environmental disasters, for example, the flooding of upland forests and peatlands caused by the dam construction in Manitoba, Canada [88]. Dam placement can cause large and frequent water level fluctuations affecting the surrounding wildlife, reducing aquatic and terrestrial quality. Blockages affect critical fish migration, observed in both the Gezhouba (China) and Tucurui (Brazil) dams [89,90], and river contamination of mercury and algae blooms resulting from stagnant water and increased sediments/nutrients upstream [91]. All these effects contribute to the higher damage score for EQ. Conversely, emissions from dam construction and maintenance are comparatively low against fossil fuels: life cycle emissions from large-scale HEP plants can be as low as 3% and 1.7% of the natural gas and coal emissions, respectively [92]. This explains the lower EI from Switzerland (CH) too, where HEP makes up a large proportion of the electricity profile, as 15% of the total CED in Switzerland still comes from fossil fuel sources, against Sweden's 4%.
Similar EI profiles can be observed in Figure 5 when water usage is included in the comparison. All countries in the sample group except Switzerland use data from the same Ecoinvent database (with European averages) which increase proportionately when accounting for water usage. Switzerland (CH) displays noticeable EI differences across the comparison study. As a small but land-locked country, Switzerland pioneered the nationwide establishment of an efficient wastewater treatment system and enshrined it into the country's first environmental legislation [93]. Its success has been reflected in the EI comparison: when water usage was included, the scores from all damage impact categories were approximately 30% lower than the European average. With electricity consumption only, the original conclusion was that SE achieved the lowest impact score but this changes when water usage is included in the calculation, as CH have lower impacts on both EQ and HH. Without the inclusion of water usage, SE has a 20% lower overall EI score, however, when water usage is included, CH has a lower overall EI by 7%, indicating that CH is now the most favourable country to operate HiPerDiF 2G from the sample group. It is likely that the actual EI of water usage in SE is lower than the European average, due to the increased construction of small on-site wastewater systems and tighter requirements for domestic water treatment, so a potential limitation of this study is that country-specific water usage data were not available [94,95]. Data of this kind are now available through the "Wastewater LCI Initiative" [96], however, they were not available during the current study.
A final important note from this part of the analysis, the energy mix in Table 1 shows a discrepancy with the CED mix of the countries in Figure 6. The electricity generation capacities in Table 1 are the maximum electrical output of each source which is different to actual power production. Renewable sources, such as solar and wind, are reliant on inconsistent weather conditions, reflected in the variations between potential and actual outputs. There are also significant energy imports/exports to and from the countries in the sample group. For example, Switzerland imported 50.9% of its total energy in 2015 [97]. Differences in total supply and final consumption of power in each country are explained by distribution and transformation losses and can be a significant margin: 29.5% of energy in Sweden was lost due to this in 2015 [98]. These are not always accounted for at the characterisation stage within SimaPro as it focuses on the net generation capacity of each actual country.

Impact Assessment of Material Transport Scenarios and Overall Country Comparison
The placement of the HiPerDiF technology (in the form of the second-generation machine) across various European scenarios can significantly affect the EI of its operation. However, the transportation of the material will also need to be calculated in order to provide a comprehensive LCA. Therefore, the system boundary has been expanded to include the transportation of reclaimed material from the reclamation facility to the remanufacturing site. By virtue of rCF being a non-degrading, stable material it has been assumed that there is no time limit on the travel route to its destination and for this reason shipping, rail and road haulage have all been considered. This assessment aims to understand if transporting material via a low-impact method such as shipping and then remanufacturing with HiPerDiF 2G in a location that sources electricity from renewable energy could result in a lower EI than remanufacturing the reclaimed material at the recycling facility that uses electricity sourced from fossil fuels. This analysis does not include the EI of the reclamation process itself, just the transportation of reclaimed materials to the HiPerDiF remanufacturing site.
In order to better understand real-world product placement and fit, it is anticipated that future optimised models of the technology, at technology readiness level (TRL) 9, would handle a higher throughput of material, measured in kg per hour instead of the current machine's output of grammes per hour (TRL 2), with higher energy efficiency. After consideration of the academic literature available on technological scale-up [99,100] and consultation with composite and LCA experts at the University of Bristol, University of Surrey, and the NCC, it was concluded that taking into account the efficiency of scaling meant it was most likely the impact per functional unit as kg/hour output was the same as the current machine (at grammes/hour output). A working hypothesis allows for more calculations to be made with operation values of a commercialised, scaled HiPerDiF model of the future, including the material transportation. This accepts that there could be a minimal amount of deviation to either side of the value in future practice.
The two main composite reclamation centres in Europe are: The site in Switzerland has been omitted from this analysis since the recommendation of an additional pump to recirculate the water through the HiPerDiF machine would require a significant reduction in the water required. The purpose of including Switzerland in the first part of the analysis was to highlight the reduction in damage with the inclusion of an efficient wastewater treatment network. However, the optimised model will be fitted with the recommended additional water tank, which may require a small increase in electricity for its functioning. Since the water would then be recirculated, there would only be a very low initial water input requirement.
A plethora of transport routes could be constructed between the sample group locations and reclamation points, demonstrated in Figure 8. For this comparison, the most direct and close to real-world options have been selected using a blend of road, rail, and sea options. The CED score for the distance travelled via each transportation method has been calculated and recorded in Table 3. Often the route by lorry or train involves a more direct route to the destination than via shipping, which is bound to established waterways. This results in indirect routes around the continent for ships, accompanied by additional lorry transport to/from port. Even so, initial analysis indicates that shipping has the lowest impact according to the CED method results, whereas road haulage is the highest.
To demonstrate the impact of each method of transportation, Figure 9 charts the IMPACT 2002+ analysis of three possible route scenarios from the ELG reclamation facility to the Hexcel manufacturing site in Stade, Germany into the four main EI categories (CC, EQ, HH, and Re). The route that is predominantly via road (including a small proportion of ferry transport across the English Channel) has significantly higher EI across all impact categories compared with the other two transport options. The route with predominantly shipping (with some road haulage to the port) is the lowest in all categories except EQ, and transport by rail sits in the middle of the two.  The largest contributing factor to the damage categories is the effect that GHG emissions have on the environment when fuel combustion occurs. Both train and lorry transport use diesel fuel, whereas ships predominantly use heavy fuel oil (HFO), lower in cost but highly polluting, or a blend of diesels, known as marine diesel oil. This can contribute to increased water and air pollution, and the devasting effects from oil spills. More recently there has been a very gradual transition towards liquified natural gas (LNG) carriers which contains less carbon per unit of energy than marine diesel [101], although LNG is predominantly methane-a significantly more potent GHG than CO 2 . Further research is required into the wider life cycle effects of LNG before more carriers make the transition. Despite this, shipping has an average decrease in EI by 80% when compared to transport by lorry. More than 10 billion tonnes of cargo are transported globally by ship each year, which is approximately 90% of total trade [102]. This transportation dominance can be partially attributed to the capacity size of the shipping containers, standardised into 20 ft eq. units (TEU) which are then efficiently stacked on ships to maximise the space available-not possible with freight transport by train or lorry [103]. This "economies of scale" effect increases the output units whilst decreasing the average unit cost [104], as well as the average EI. TEU shipping containers can be effectively loaded directly onto cargo trains and lorries, to be transported to inland destinations.
Rail can also be an efficient method of bulk transportation over long distances, but the routes are not as flexible as road haulage. Where locations do not benefit from rail access, costly transhipment costs will apply, blocking the wider adoption of rail for freight transports. Within Europe, some trains run on electricity and others on diesel, and this varies from country to country. Whilst it is accepted that diesel-powered trains have a higher EI than electricity-powered, the result could also vary if the electric train running through France receives electricity predominantly from nuclear power generation, as opposed to a renewable energy source [105]. Within the UK, the government strategy is to optimise the current rail network and encourage the transfer of road haulage to train, potentially reducing GHG emissions in order to hit the "Net-zero by 2050" legal mandate [33]. It is estimated that each tonne of freight transported by rail reduces carbon emissions by 76% compared to road haulage, and each freight train removes 43 to 76 lorries from the roads [105]. However, the UK's electrical grid would need to significantly decarbonise its current power source in order to reach the maximum benefits of this transition. The EI of logistics and transportation are currently under extreme scrutiny, with research also considering the role that hydrogen fuel cells could play in the future.
Road haulage is currently the highest impact method of freight transportation in this analysis, as indicated by the highest impact across all categories, despite accruing the fewest miles travelled. This is what makes transport by road so convenient: lorries can take advantage of the most direct routes between locations. There are other negative social consequences of road haulage which are not included in this analysis, such as increased traffic and noise pollution, which disrupts human and animal physical and mental health. If the cost of transportation and other market forces were not an issue, transport by road should be completely avoided. Shipping is the lowest EI form of longdistance transportation, and potentially most cost-effective. However, it is also one of the slowest. Whilst this is suitable for these relatively inert reclaimed fibres, the flexibility of transport by lorry over shipping and rail means road haulage is, unfortunately, more popular; it is estimated that around 70% of freight within the US is transported by lorry [106]. However, recent developments in electrification for road haulage means it is very gradually becoming more environmentally attractive [107,108], but the true costs of these changes are yet to be fully understood.
The final analysis of this study combined the route to each remanufacturing location that received the lowest CED score (from Table 3 highlighted in green) with the processing impact of the HiPerDiF 2G operation. Using IMPACT 2002+ analysis, the original four impact categories (CC, EQ, HH, and Re) were compared to establish the lowest impact option overall. The results are presented in Figure 10.
Without CH included in the sample group, SE is now the country with the overall lowest EI for operating the HiPerDiF technology. Transporting material to the HiPerDiF 2G location in SE from CU Nord (via shipping) was also the lowest impact transport option across the entire sample group, despite being the second longest in distance.
The second optimal overall scenario is from CU Nord to Hexcel Composites (DE), which requires virtually no transportation. The effect of moving large quantities of reclaimed material around the same facility, even if the site is large, will be negligible when compared to the other distances travelled across this sample group. The next highest impact overall was ELG, Birmingham (UK) to NCC, Bristol (UK) via rail scenario-the shortest distance travelled of all four scenarios-where the impact of transportation on all of the damage categories is practically negligible. The smallest change in overall EI occurred when transporting material within the UK or DE because the two main fibre reclamation centres are based in these countries, resulting in reduced transport distances. Despite this, the UK and DE still have the highest impact on CC and Re categories due to the heavy reliance on power from fossil fuels. The UK's electricity is generated from a slightly higher proportion of fossil fuels than DE, as reflected in the marginally higher impact scores for CC and Re for electricity. Transport burdens do become more significant for countries having a lower fossil fuel reliance, as reflected by the lower HH impacts for SE and FR. Although SE has the second-longest distance to travel, it has the lowest impact of these three scenarios because it used only shipping from CU Nord-the least damaging transportation method-which is impossible for the land-locked locations in the UK and FR. For the EQ damage category, the transport burden is negligible since these impacts are associated with large amounts of water waste. Even with the scaled increase in fibre concentration to 1 kg of preform produced per hour, it would require the same amount of water and is therefore still the largest contributing factor for that impact category. However, the impact on EQ in the DE scenario is nearly equal to SE with the inclusion of transportation in the system boundary, attributed to the impact of SE's HEP generation on the surrounding ecosystems.
The most damaging scenario was for transporting the material from ELG to FR via shipping and road haulage. Despite this scenario being the longest distance, nearly 18% of the total distance travelled is via road haulage. It has been previously discussed that transportation by road is the highest impact method available in this analysis, so it can be deduced that the larger impact scores can be attributed to the lorry section of the route. Since FR generates its electricity predominantly from nuclear, this pushes up the impact on Re and reduces the impact on CC.

Interpretation and Future Considerations
This study identifies the challenges of recycling CFRP, with respect to the resulting degraded material, complications with dismantling and transportation, and reduced economic value of onward applications of the material. Completing analyses holistically and iteratively with LCA highlights the interconnectivity of environmental problems, and that focusing on one aspect will shift burdens to another. Consideration of EI early in the design of new technology can result in more sustainable processes being developed.
There are many additional factors that have not been considered in this study that can affect the final EI score. Some of the transport routes in these analyses are unrealistic since the calculated distances are linear. In real-world conditions, trains would follow existing rail lines, some of which may not include industrial freight transport. Lorry transport would be required along more sections of each route, which was an impractical consideration for this study. Haulage arrangements post-Brexit have been significantly disrupted with hauliers declining to take on loads destined for the UK coupled with increased freight charges and paperwork [109]. However, it is unknown at this stage how this will shape long-term logistics between the UK and the EU. The differences in landscapes and weather conditions can significantly alter the amount of fuel required. Additionally, the energy sector across Europe is changing in response to growing concerns over climate change: the UK has increased the offshore wind farm [110] and DE is phasing out their nuclear power plants, along with some other countries [111].
Recycling a product at the end of its life should result in ecological benefits when compared with producing virgin material for the next product life cycle, but often this is unfortunately not always the case. There are other issues at EOL which contribute to the EI beyond the remanufacturing process which has not been considered in this analysis, such as disassembly of the product, reducing the size, transporting the waste to the recycling facility, and treating the reclaimed fibres to be compatible with the remanufacturing process. The EI of the reclamation processes themselves will need to be accounted for in a fully comprehensive LCA, including the energy, material, and equipment inputs for pyrolysis and solvolysis, the two commercial fibre reclamation methods available at the moment. The main input for pyrolysis is heat, and for solvolysis, it would be the production of the chemicals [112,113].
As more composite structures reach the end of their useful life and the amount of reclaimed fibre accumulates, strategic decisions over the location of HiPerDiF technology in relation to the reclamation facility will need to be carefully considered. Much like the variation in EI across the locations for operating HiPerDiF, the location of these reclamation facilities could also affect the overall EI. Considering the EOL supply chain in the future, further research could be to investigate if the establishment of specialised carbon fibre composite waste processing hubs would result in lower EI and economic costs. For example, a coastal location surrounding the North Sea with electricity from renewable energy sources that could reclaim and remanufacture fibres from EOL offshore wind turbines, or a hub in relative proximity to a major airport or aircraft decommissioning centres, that can specialise in recycling fibre from decommissioned aircraft. Early consideration of these logistical issues can establish how HiPerDiF technology can best fit into these supply chains to ensure that the EI of reclamation remains low whilst maximising the economic value it can bring to second-life carbon fibre.
Another significant trade-off is the economic implications, which have not been considered in this report. When decisions are made, potential economic benefits have long outweighed environmental factors. The cost of reclaimed fibres will vary depending on the supplier: ELG is one of Europe's largest CFRP recycling companies by commercialising pyrolysis with an annual process rate of 2000 tonnes/yr [114]. With this volume, it could be more cost-effective than CU Nord [115]. High quality recyclate generates market demand, and therefore the addition of the innovatory HiPerDiF approach to realigning rCF should add value to recyclate, indicating that fully recycling carbon fibres in this way would make economic sense. The inventory data collected for this LCA can also be used to inform a life cycle costing (LCC) analysis.
Finally, these results were generated using two LCIA methods, IMPACT 2002+ and CED. Future analyses should include other impact assessment methods to validate the optimised model before commercialisation. This LCA focused on a gate-to-gate remanufacture process, with the widening of the boundary to include transportation costs, but further work would expand the system boundary to consider the full decommissioning and reclamation impacts of the EOL phase, incorporation of emerging fibre reclamation technologies such as fluidised-bed processing, and a comparison with the EI of virgin composite production. This HiPerDiF conceptual technology has presented the composites industry with a potential solution to close the loop on EOL waste, keeping material within the industrial system. Since the completion of this report, a scaled third generation HiPerDiF (3G) machine has been constructed at the National Composites Centre in Bristol, UK. This development is fully instrumented, automated, designed for 100 m/hr throughput and has incorporated the results of this paper to optimise the PED of the next-generation model. Furthermore, a spin-out company (Lineat Composites, https://lineat.co.uk/, accessed on 23 December 2021) has recently been formed to commercialise the technology. An updated holistic and iterative LCA study is recommended after the HiPerDiF 3G technology optimisation to account for these changes, and further highlight the interconnectivity of the environmental and economic issues at EOL. Together with industrial partners, this study will assist with establishing HiPerDiF's best fit within the supply chain and should include a cost analysis to fully remanufacture waste composite, including detailed transport routes.

Conclusions
The LCA presented in this report has assessed the EI associated with a HiPerDiF 2G technology prototype. The intention was to address the identified environmental hotspots for the next optimised model whilst also scaling up the productivity of the resulting preform. The HiPerDiF technology is an effective methodology to remanufacture rCF into high performance recycled composites. To date, its capability has been limited to laboratory-scale performance, but the construction of a scaled-up machine (HiPerDiF 3G) should improve this aspect considerably.
The vacuum suction appliance had the greatest EI in three of the four damage categories, consuming 64% of the total power of the machine.
Water usage accounted for 84% of damage to EQ of operating HiPerDiF, predominantly due to the water not being reused. The addition of a full water recirculation system has been proposed in order to reuse the water for each cycle. Recirculating the water for each cycle of this process will significantly minimise the overall requirement, especially as the technology is scaled-up.
Whilst this impact analysis is a rudimentary step to understand the implications of recycling carbon fibre, this result indicates that location and logistics, i.e., the distance between reclamation and remanufacturing facilities, can have a large impact on the overall environmental scores of remanufacturing reclaimed fibres: Countries with a decarbonised electricity grid are preferable for minimal processing impact associated with the operation of HiPerDiF. b.
Transportation of reclaimed material via shipping from a country with electricity predominantly generated from non-renewable sources to a country using electricity from predominantly renewable sources results in a lower EI overall. Although shipping is a slow form of transport, the quality of the inert fibre material would not be affected by long delivery times. Road transport resulted in the highest EI in all modelled routes. c.
If it were not possible to position the HiPerDiF 2G in a location that receives electricity from renewable sources, then the next least damaging option would be to locate the machine close to reclamation centres to minimise the EI attributed to material transportation. The colocation of the reclamation and of the remanufacturing facility in a dedicated centre able to generate its own electricity from renewables on site would be the ideal solution for companies that are setting up from scratch.
This study was completed on the conceptual HiPerDiF second prototype (HiPerDiF 2G), and a second evaluation should be conducted on the optimised third-generation model (HiPerDiF 3G) recently completed at the National Composites Centre in Bristol, UK.
The results of this study demonstrate a methodology to evaluate the environmental impact of this new technology at early conceptual development via LCA informed by primary data collection. Moreover, this work offers an example of how to investigate the possible implications of placing a new technology in the current European supply chain considering different scenarios.