Evaluating Evaporative Cooling Assisted Solid Desiccant Dehumidification System for Agricultural Storage Application

The study aims to investigate Maisotsenko cycle evaporative cooling assisted solid desiccant air-conditioning (M-DAC) system for agricultural storage application. Conventional air-conditioning (AC) systems used for this application are refrigeration-based which are expensive as they consume excessive amount of primary-energy. In this regard, the study developed a lab-scale solid silica gel-based desiccant AC (DAC) system. Thermodynamic performance of the developed system was investigated using various adsorption/dehumidification and desorption/regeneration cycles. The system possesses maximum adsorption potential i.e., 4.88 g/kg-DA at higher regeneration temperature of 72.6 °C and long cycle time i.e., 60 min : 60 min. Moreover, the system’s energy consumption performance was investigated from viewpoints of maximum latent, sensible, and total heat as well as latent heat ratio (LHR), which were found to be 0.64 kW, 1.16 kW, and 1.80 kW, respectively with maximum LHR of 0.49. Additionally, the study compared standalone DAC (S-DAC), and M-DAC system thermodynamically to investigate the feasibility of these systems from the viewpoints of temperature and relative humidity ranges, cooling potential (Qp), and coefficient of performance (COP). The S-DAC system showed temperature and relative humidity ranging from 39 °C to 48 °C, and 35% to 66%, respectively, with Qp and COP of 17.55 kJ/kg, and 0.37, respectively. Conversely, the M-DAC system showed temperature and relative humidity ranging from 17 °C to 25 °C, and 76% to 98%, respectively, with Qp and COP of 41.80 kJ/kg, and 0.87, respectively. Additionally, the study investigated respiratory heat generation rate (Qres), and heat transfer rate (Qrate) by agricultural products at different temperature gradient (∆T) and air velocity. The Qres and Qrate by the products were increased with ∆T and air velocity, respectively, thereby generating heat loads in the storage house. Therefore, the study suggests that the M-DAC system could be a potential AC option for agricultural storage application.


Introduction
The world's population has grown rapidly over the past few decades and is predicted to move to about 9.8 billion by 2050. Due to this population growth, the demand for food will rise about 70% by 2050 [1]. The agriculture sector plays a significant role in managing global food demand. Being an agriculture-dependent country, Pakistan produces 13.67 million tonnes of fruits and vegetables, but about 35-40% of total production is lost owing to post-harvest losses [2]. The post-harvest losses refer to degradation of quality as well as quantity of the agricultural products. One of the most important reasons for the postharvest losses is high amount of moisture content available in the agricultural products [3,4]. Moreover, several factors are responsible for the post-harvest losses as shown in Figure 1 [5]. After harvesting, fruits and vegetables perform respiration, transpiration, and ripening processes. These decay processes of agricultural products can be minimized by providing optimum storage conditions i.e., temperature and relative humidity [6]. Conventional storage techniques are equipped with refrigeration-based systems which consume huge amount of primary energy as well as degrading the environment by utilization of harmful refrigerants [7]. Moreover, these systems are incapable of providing the appropriate temperature and relative humidity conditions especially for agricultural products [8]. In this regard, alternative energy-efficient and environment-friendly options are available including evaporative cooling (EC), and desiccant air-conditioning (DAC) systems. The EC options are direct EC, indirect EC, and Maisotsenko cycle EC (MEC) systems i.e., an advanced form of the indirect EC [9]. The MEC system thermodynamically lowers the ambient air temperature by utilizing psychrometric accessible renewable energy [10]. Two thermodynamic operations which involve EC and heat transfer stipulate a cooling effect where ambient air almost approaches the dew point temperature rather than wet bulb temperature [9,11]. The MEC system has been investigated in literature for heating, ventilation, and air-conditioning applications [12][13][14][15][16]. However, the potential of the standalone EC systems is limited in humid areas [16,17]. Therefore, to overcome this limitation, the DAC system is an emerging option because of its potential to provide promising results in humid climates [18][19][20]. The main component of the DAC system is desiccant material which adsorb moisture from ambient/process air and thereby dehumidify the air. The adsorption/dehumidification and desorption/humidification processes are mainly dependent on characteristics of adsorbents [21][22][23]. The DAC systems are energy efficient as they are operated or regenerated with thermal energy that could be available through low-grade waste heat and renewable energy sources. Niu et al. [24] experimentally compared the energy saving potential of the DAC system with conventional refrigeration-based AC system. The study concluded that the DAC system had a maximum energy saving potential of about 58.9% [24]. Jia et al. [25] conducted an experimental study on the DAC system's ability to remove moisture from the air and its energy saving potential as compared with a conventional AC system. The study showed an energy saving potential of about 37.5% as compared with a conventional AC system [25]. Similar studies are reported in the literature which showed good energy saving potential by the DAC systems for various AC applications [26][27][28][29]. However, the standalone DAC (S-DAC) system i.e., without the integration of MEC with the DAC system, could not achieve appropriate temperature and relative humidity conditions particularly for agricultural product storage [9,[30][31][32]. In this regard, an MEC system integrated with a DAC (M-DAC) system combines characteristics of both S-DAC and MEC systems, and thereby has potential to achieve sensible load via MEC and latent load through the DAC system [8]. The M-DAC system has been investigated in literature for various agricultural applications which involve greenhouse AC [33,34], livestock AC [35,36], and poultry AC [37][38][39][40]. The M-DAC system has shown promising results for these agricultural applications.
In this study, a lab-scale solid silica gel-based DAC system was developed. The performance of the developed system was investigated thermodynamically, using various adsorption/dehumidification and desorption/regeneration cycles. Furthermore, performance of the developed system regarding energy consumption was investigated from the viewpoints of latent heat (Q L ), sensible heat (Q S ), and total heat (Q T ) as well as latent heat ratio (LHR). The study proposed two kinds of AC system involving standalone DAC, and MEC-assisted DAC systems for potential application in agricultural product storage. A thermodynamic analysis was conducted for both systems to explore applicability of these systems considering temperature and relative humidity conditions, cooling potential (Q p ), and coefficient of performance (COP). In addition, the study investigates respiratory heat generation rate (Q res ) and heat transfer rate (Q rate ) to investigate heat loads by the agricultural products.

Temperature/Humidity Requirements for Agricultural Storage Application
The storage and handling of agricultural products is one of the key issues of the 21st century because of the intricate mechanisms of transpiration, respiration as well as chilling injury. Appropriate temperature and relative humidity conditions are a primary concern to reduce post-harvest losses. The shelf life of agricultural products is a function of storage temperature. The storage temperature effect on the shelf life of fruits and vegetables is represented in Figure 2. A higher storage temperature reduces the shelf life of fruits and vegetables, while a lower storage temperature could increase the shelf life as represented in Figure 2. Moreover, the quality, composition, and texture of the products are significantly influenced by the temperature [41][42][43]. Figure 3 shows the effect of storage temperature on quality of peach, Boston-type lettuce, and asparagus. As the storage temperature increases the quality of the products decreases.
After harvesting, fruits and vegetables behave like living organisms and perform respiration processes according to Equation (1) available in ref. [46]. When ambient air oxygen combines with the product's conserved sugar/starch, carbon dioxide and water are generated, thereby releasing respiration heat. In order to minimize respiration rate, the agricultural products should be stored at low oxygen level. However, as the temperature rises, the respiration rate increases, thereby reducing the shelf life of the product. The influence of temperature on respiration rate by some fruits and vegetables is shown in Figure 4. The effect of temperature on some fruits is shown in Figure 4a, which shows respiration rate increases with temperature. Similarly, the effect of temperature on vegetables in Figure 4b shows that the respiration rate increases with temperature. This respiration rate increases heat i.e., respiratory heat in a storage house. The quantity of moisture present in the ambient air, expressed as relative humidity, is the primary driver of water loss from harvested goods. The agricultural products preserve their nutritional quality, flavour, and appearance at high relative humidity. In contrast, shrivelling occurs at low relative humidity ranges because of excessive transpiration [47,48]. In this regard, the optimum temperature and relative humidity conditions for fruits and vegetables are available in refs. [19,49] ranging from −5 • C to 25 • C, and 85% to 95%, respectively. Figure 5 represents the optimum temperature and relative humidity zones for storage of fruits and vegetables with the climatic conditions of Multan.

Standalone Desiccant Air-Conditioning (S-DAC) System
Referring to the Figure 6a, components of the S-DAC system consist of desiccant block, a sensible heat exchanger (SHX), and a heating source. Ambient/process air is entered into the block during the adsorption process and gets dehumidified, which thereby increases the temperature of the air due to the release of the heat of adsorption. After that, the dehumidified air is entered into the SHX which ideally reduces the temperature to ambient air temperature. During the desorption process of the S-DAC system, ambient air was utilized as a return air and directed towards the SHX, which thereby gets heated. Then, this processed heated air enters a heat source which can be operated with thermal energy options like low-grade waste heat as well as renewable energy options such as solar thermal heat and biogas/biomass, etc. In the end, this heated air is directed to a desiccant block which carries away water vapours from the desiccant material to regenerate and hence remove humid air.

M-Cycle Integrated Desiccant Air-Conditioning (M-DAC) System Collection
Referring to Figure 6b, components of the M-DAC system consist of desiccant block, SHX, MEC, and a heating source. Ambient air is directed into the block during the adsorption process of the M-DAC system and gets dehumidified, thereby increasing the temperature due to the release of the heat of adsorption. After that, the dehumidified air is directed towards the SHX which decreases the process air temperature to nearly that of the ambient air without change in the humidity ratio. This cooled process air is further directed towards the MEC which lowers the process air temperature sensibly which could be supplied to the agriculture storage house. During the desorption process of the M-DAC system, ambient air, as a return air, is employed and enters the SHX, which thereby gets heated. Then, this processed heated air is directed towards the heat source which can be operated with thermal energy options like low-grade waste heat and renewable energy options such as solar thermal heat and biogas/biomass, etc. In the end, this heated air is directed towards desiccant block which carries away water vapours from the block to regenerate it and hence remove the humid air.

Experimental Setup
The solid silica gel-based DAC system was developed at laboratory scale. The experimental setup was mainly consisted of solid silica gel, sieves, heat exchanger (i.e., fan heater), temperature, relative humidity, pressure, and velocity (anemometer) measuring sensors. Figure 7a shows the photographic view of the developed experimental setup. The sieves are fabricated by using polyacrylic plastic material frame and mesh to support the material and easy crossing of air. A total of 18 sieves were used to develop the desiccant unit and each sieve has a dimension of 220 mm × 145 mm × 3 mm and carrying~68 g of silica gel. These sieves are stacked over each other to form a desiccant unit and then insulated on the sides. The important parameters for desiccant unit and silica gel used in this study is shown in Table 1. The fan was used to continuously throw the process air at velocity of about 3.5 m/s, resulting in a mass flow rate ( . m a ) of about 0.14 kg/s. The temperature, relative humidity, and pressure sensors were placed at the inlet and outlet sides of the desiccant unit to measure the experimental conditions. The measurement range and absolute accuracy for temperature, relative humidity, pressure, and velocity sensors is about −40 • C to 80 • C; ±2 • C, 0% to 100%; ±5%, 75 kPa to 110 kPa; ±0.3 kPa, and 0.3 m/s to 30 m/s; ±1.5 m/s, respectively.  The experimental process is divided into two stages: desorption/regeneration and adsorption/dehumidification. Figure 7b shows a schematic representation of the developed experimental system. During the regeneration process, hot air (achieved by heat exchanger) is supplied to the desiccant unit to primarily reactivate the adsorbent. After that, the dehumidification process commences, and process air is directed to the desiccant unit and moisture adsorbs on the material's surface because of its hygroscopic nature, thereby increasing the temperature of process air due to the release of heat of adsorption [51]. In this study, four desorption as well as adsorption cycles were conducted at different regeneration temperatures. The regeneration temperature was set at 68 • C, 69.2 • C, 70.5 • C, and 72.6 • C for cycles 1, 2, 3 and 4, respectively. Figure 8 shows the performance of the experimental system at different regeneration temperatures by conducting various desorption/adsorption cycles. The system has shown maximum dehumidification potential at higher regeneration temperature of 72.6 • C. In this regard, the study focuses on the desorption and adsorption cycle-4 to thermodynamically explore the performance of the system.
Ideally, the adsorption process follows isenthalpic behaviour, which means that the heat of water vapor condensation following the vapor stage to liquid stage is the same as the heat of adsorption. However, experimental studies have shown that the heat of adsorption is higher than the ideal adsorption heat because of the isosteric heat of adsorption [51,52]. The difference between an ideal isenthalpic line and the actual dehumidification line is mainly due to the type of adsorption mechanism and interaction between adsorbent pairs. Figure 9 represents the psychrometric behaviour of the ideal and experimental dehumidification line and cyclic behaviour of proposed DAC systems. The points 1-8 were calculated by considering the experimental inlet and outlet conditions.

Data Reduction
The experimental data of the developed DAC based on various desorption and adsorption cycles were obtained to investigate the performance thermodynamically. The inlet and outlet air conditions of both desorption and adsorption cycles were measured during the experiments. After that, Equation (2) was used to calculate the output air condition of the SHX [19,53]. The modelled Equation (3) of the MEC was used to calculate the performance of the MEC system [36,54]. Ambient air as a return air was used to increase the air temperature to some extent by Equation (4). Maximum desorption potential (∆X des ) and adsorption (∆X ads ) potential were calculated from Equations (5) and (6) [31].
∆X ads = X in, ads − X out,ads where, the subscripts 1-6, and DB, are process air conditions represented in Figure 6, and dry-bulb, respectively. T is air temperature ( • C), ε SHX is the effectiveness of sensible heat exchanger defined by the American Society of Heating, Refrigerating, and Air-Conditioning Engineers (ASHRAE) [46], X is humidity ratio (g/kg-DA), ∆X des is desorption potential (g/kg-DA), ∆X ads is adsorption potential (g/kg-DA), X in, des is inlet humidity ratio during desorption process (g/kg-DA), X out,des is outlet humidity ratio after desorption process (g/kg-DA), ∆X ads is adsorption potential (g/kg-DA), X in, ads is inlet humidity ratio during adsorption process (g/kg-DA), and X out, ads is outlet humidity ratio after adsorption process (g/kg-DA), respectively. The performance of the developed desiccant unit regarding energy consumption can be evaluated by latent heat ratio (LHR) [55]. The LHR is the ratio of latent heat consumed to the total energy consumed by the system which is given in Equation (7). The total energy (Q T ) consumed by the system was calculated from Equations (8)-(11) based on sensible heat (Q S ), latent heat (Q L ), and electricity consumed by the fan (Q F ) to supply the process air [55]. However, Equations (12)- (14) were used to calculate cooling potential (Q p ) by the proposed S-DAC and M-DAC system, respectively. Similarly, Equations (13) and (14) were used to calculate the coefficient of performance (COP) by the proposed S-DAC, and M-DAC system, respectively. The air enthalpy was calculated by Equation (15) [46].
m a C p (T des,in − T des,out ) (9) m a (h ads,in − h ads,out ) (10) where, LHR is latent heat ratio (-), Q L is latent heat consumption (kW), Q T is total heat consumption (kW), Q S is sensible heat consumption (kW), Q F is electricity consumed by fan (kW), . m a is mass flow rate (kg/s), C p is specific heat capacity of air (kJ/kg K), T des,in is the inlet temperature of desorption process (K), T des,out is the outlet temperature of the desorption process (K), ∆X ads is adsorption potential (g/kg-DA), γ is latent heat of vaporization with respect to temperature (kJ/kg), h ads,in is inlet enthalpy of adsorption process (kJ/kg), h ads,out is outlet enthalpy of adsorption process (kJ/kg), . V air is volume flow rate (m 3 /s), dP is pressure drop (kPa), and ε F is efficiency of the fan taken as 70%. The subscripts 1, 3, 4, 5, 6, 7 S-DAC, and M-DAC, and DB refer to air states as shown in Figure 6, standalone desiccant air-conditioning, M-cycle integrated desiccant air-conditioning system, and dry bulb, respectively. Q p is cooling potential (kJ/kg), h is air enthalpy (kJ/kg), and COP is coefficient of performance (-), respectively.

Uncertainty Analysis
In the experimentation process, there are always errors in calculating/measuring variables due to the inaccuracy of instruments, design limitations, ambient conditions, observations, human errors, and other associated important factors. After experiments, an uncertainty analysis was performed to determine the level of uncertainty in estimating the variables (temperature, relative humidity). Estimating the experimental uncertainty gives confidence in the calculated results. The method is named as the root of the sum of square methods and Equation (17) is used to measure the uncertainty [56][57][58].
where, σ R is the total uncertainty (%) and α 1 -α N represent the uncertainty in independent variables, N 1 -N n represent the independent variables R is given a function of the independent variable. Table 2 shows the uncertainty analysis of various parameters used in this study.

Heat Load Calculations for Agricultural Storage Application
The storage of agricultural products offers considerable challenges as they generate heat during storage by consuming oxygen and emitting carbon dioxide, water vapours and heat transfer between product and ambient air. The respiratory process varies with temperature as well as type of the product. Becker et al. [59] developed a relationship of measuring respiratory heat generation rate as a function of the temperature of the agricultural product, given by Equation (18). Furthermore, heat is removed from the product due to heat transfer between product and ambient air which was calculated by Equation (19) [60].
where, Q res is respiratory heat generation rate (W/kg), T is temperature of the product ( • C), f and g are respiratory coefficients depending upon the agricultural product. Table 3 shows the respiratory coefficients of some selected fruits and vegetables. Q rate is heat transfer rate from the product (W), h s is surface heat transfer coefficient (W/m 2 • C), A s is surface area covered by a product (m 2 ), ∆T is temperature difference between product surface and ambient air ( • C), T s is surface temperature of product ( • C), and T a ambient or surrounding air temperature ( • C). The h s vary with velocity of ambient air, product orientation and geometry. Several studies have investigated the h s against ambient air velocity, and the A s for various agricultural products presented in Table 4. In this principle, behavior of the Q rate from the agricultural products has been explored by considering literature data of h s against air velocity, and A s . Table 3. Respiratory coefficients of some fruits and vegetables, reproduced from ref. [59].

Results and Discussion
The performance of the desiccant unit was examined thermodynamically for various desorption and adsorption cycles. Figure 10 shows experimental desorption and adsorption cycles profiles of temperature for the developed DAC system at different desorption temperatures (T des ). The switching time of 1:1 (equal time for both stages) was considered for the desorption and adsorption cycles. These cycles were conducted to explore optimum switching time, and desorption/regeneration temperature for higher coefficient of performance and maximum adsorption potential. The temperature cycles represent that 20 min:20 min, 30 min:30 min, 45 min:45 min, and 60 min:60 min was set for the desorption and adsorption cycle 1, 2, 3 and 4, respectively. The outlet temperature (after adsorption process) ranges from 39 • C to 62 • C (cycle-1), 37 • C to 57 • C (cycle-2), 43 • C to 59 • C (cycle-3), and 44 • C to 63 • C (cycle-4), respectively. The process air temperature increases due to release of heat of adsorption. Figure 11 shows experimental desorption and adsorption cycles profiles of relative humidity for the DAC system. The outlet relative humidity (after adsorption process) ranges from 17% to 35% (cycle-1), 22% to 40% (cycle-2), 23% to 43% (cycle-3), and 20% to 38% (cycle-4), respectively.  . Experimental desorption/regeneration and adsorption/dehumidification cycle profiles of relative humidity for the DAC system at different desorption temperature (T des ). Figure 12 shows experimental desorption and adsorption cycle profiles of humidity ratio for the developed DAC system. The adsorption cycle-4 represents maximum adsorption potential due to higher desorption temperature. Figure 13 shows desorption and adsorption potential (∆X) in different experimental cycles. In the desorption process, the amount of water vapours desorbed increases rapidly, and then reduces when saturation pressure of the process air and desiccant material surface approach equilibrium. Consequently, when the adsorption process starts, the amount of water vapours adsorbed is quite high, but gradually decreases and becomes steady due to saturation condition of the desiccant material. In Figure 13, the 60 min adsorption cycle-4 represents the maximum adsorption potential of 4.8 g/kg-DA via desiccant unit at desorption temperature of 72.6 • C, thereby showing the significance of switching time for the system and desorption temperature, which are the most important parameters for the feasibility of the DAC system [19]. Moreover, Aleem et al. [53] investigated the performance of laboratory scale silica gel-based DAC system thermodynamically. According to the results, maximum adsorption potential and coefficient of performance was observed at higher desorption temperature of 70 • C and 60 min:60 min cycle time. In this regard, the adsorption cycle-4 has been explored for performance evaluation of the developed system.  The performance of the developed desiccant unit regarding energy consumption was explored from viewpoints of latent heat (Q L ), sensible heat (Q S ), total heat (QT) consumed by the system, and latent heat ratio (LHR) as shown in Figure 14. The Q L consumed by the system during the adsorption process varied between 0.02 kWh and 0.64 kWh. The Q S consumed by the system during desorption process varied between 0.20 kW and 1.16 kW. The Q S was higher due to heat provided for desorption of water vapours from the desiccant material to regenerate it. The energy consumed to reach the high desorption temperature of 72.6 • C directly influenced the total energy consumed by the system. In this regard, the Q T consumed by the system varied between 0.15 kW and 1.80 kW during both adsorption and desorption processes. However, the Q T consumption could be reduced by maintaining a lower desorption temperature while, according to the experimental results, a higher desorption temperature was necessary for maximum adsorption potential. The electricity consumed by the fan was found to be 6.38 W. The LHR by the developed system varied between 0.02 and 0.49. The proposed air-conditioning (AC) systems are energy-efficient as compared with conventional refrigeration-based AC systems as discussed in Section 1. Figure 14. Latent heat (Q L ), sensible heat (Q S ), and total heat (Q T ) consumed by the experimental system, and latent heat ratio (LHR) achieved by the system during desorption and adsorption cycle-4. Figure 15 shows temperature and relative humidity profiles for the adsorption cycle-4 using S-DAC, and M-DAC system. The temperature and relative humidity of the S-DAC system ranges between 39 • C and 48 • C, and 35% and 66%, respectively. Therefore, the S-DAC system was unable to achieve the appropriate temperature and relative humidity conditions for storage of the agricultural products. Similarly, the temperature and relative humidity of the M-DAC system ranges from 17 • C to 25 • C, and 76% to 98%, respectively, and could thereby be a potential option for the storage of agricultural products. The tem-perature and relative humidity profiles of the S-DAC, and M-DAC system for adsorption cycle-1, cycle-2, and cycle-3 is available in Appendix A: Figures A1-A3, respectively.   Figure 18 shows psychrometric representation for performance of the proposed DAC systems. In Figure 18, the S-DAC system could not achieve appropriate temperature and relative humidity conditions for the storage of agricultural products. In contrast, the M-DAC system has achieved appropriate temperature and relative humidity conditions for the storage of agricultural products. Therefore, the M-DAC system could be utilized for the potential application of agricultural products storage.   The fruits and vegetables respire as living organism by emitting carbon dioxide to surrounding environment, thereby causing respiratory heat generation (Q res ). The Q res vary with temperature and type of the product. Figure 19 shows the effect of temperature on the Q res by some fruits and vegetables. The Q res increases with temperature, hence during storage respiration process should be kept as low as possible to avoid heat generation from the product. In addition, heat is removed from the product due to the Q rate between product and ambient or surrounding air i.e., the difference between surface temperature of product and surrounding air temperature (∆T), and velocity of air. Figure 20 shows the effect of the ∆T and air velocity on the Q rate by some selected fruits (apple, grape, orange, pear, and tomato). The Q rate by fruits increases with increase in air velocity and ∆T. In case of apple the Q rate at 0.91 m/s, with ∆T of 5 • C was 1.58 W, but at same velocity with ∆T of 10 • C, 15 • C, and 20 • C, the Q rate was 3.16 W, 4.75 W, and 6.33 W, respectively. A similarly increasing trend of the Q rate at different air velocity and ∆T was observed by other selected fruits. Likewise, Figure 21 shows the effect of ∆T on the Q rate by some selected vegetables (cabbage, carrot, onion, and potato). The Q rate by vegetables increases with ∆T. In case of cabbage, Q rate at 0.431 m/s with ∆T of 5 • C was 0.116 W, but at same velocity with ∆T of 10 • C, 15 • C, and 20 • C the Q rate was 0.22 W, 0.33 W, and 0.45 W, respectively. A comparable trend was observed for other selected vegetables. Furthermore, higher air velocities and higher relative humidity of surrounding air caused wilting of fruits and vegetables. The appropriate air velocity is varied with size of storage house. The recommended air velocity is about 0.003 m/s for storage house having area of 10 m 2 , and relative humidity of about 90% to 95% [50].

Conclusions
The present study aims to evaluate the Maisotsenko cycle evaporative cooling assisted solid desiccant air-conditioning (M-DAC) system for agricultural storage application. The agricultural products required appropriate temperature and relative humidity conditions for their efficient storage to avoid post-harvest losses. In this regard, the air-conditioning (AC) system is principally required to optimize the temperature and relative humidity conditions, which could potentially reduce post-harvest losses. Therefore, in this study, a lab-scale solid silica gel-based desiccant AC (DAC) system was developed. The performance of the developed system was investigated thermodynamically, using various adsorption/dehumidification and desorption/regeneration cycles. The system possesses better performance in terms of adsorption potential (Q p ) i.e., 4.88 g/kg-DA at higher desorption temperature i.e., 72.6 • C and comparatively long cycle time i.e., 60 min:60 min. Furthermore, performance of the developed system regarding energy consumption was investigated from viewpoints of latent heat (Q L ), sensible heat (Q S ), and total heat (Q T ) as well as latent heat ratio (LHR). The maximum consumption of Q L , Q S , and Q T , by the system was found to be 0.64 kW, 1.16 kW, and 1.80 kW, respectively by achieving the maximum LHR of 0.49.
Furthermore, the study proposed two kinds of AC options involving standalone DAC (S-DAC), and M-DAC systems to investigate applicability of these systems for agricultural storage application. The proposed systems were compared thermodynamically from perspectives of temperature as well as relative humidity ranges, cooling potential (Q p ), and coefficient of performance (COP). The S-DAC system showed temperature and relative humidity ranging from 39 • C to 48 • C, and 35% to 66%, respectively, with Q p and COP of 17.55 kJ/kg, and 0.37, respectively, which were inappropriate conditions for agricultural storage. Conversely, the M-DAC system showed temperature and relative humidity ranging from 17 • C to 25 • C, and 76% to 98%, respectively, with Q p and COP of 41.80 kJ/kg, and 0.87, respectively which lies somehow between appropriate conditions for the agricultural products storage application. Additionally, the study investigated respiratory heat generation rate (Q res ), and heat transfer rate (Q rate ) by some fruits and vegetables at different temperature gradient (∆T) and air velocity. The Q res and Q rate by the fruits and vegetables were increased with temperature, and ∆T as well as air velocity, respectively. These heat loads reduced shelf life and quality of agricultural products. Therefore, the M-DAC system could be a potential AC option for agricultural storage application.

Conflicts of Interest:
The authors declare no conflict of interest. V air volume flow rate (m 3 /s) X humidity ratio (g/kg-DA) ∆X ads adsorption/dehumidification potential (g/kg-DA) ∆X des desorption/regeneration potential (g/kg-DA) ∆T temperature gradient ( • C)