Effectiveness of Road Cool Pavements, Greenery, and Canopies to Reduce the Urban Heat Island Effects

: The ongoing climate change is manifesting itself through the increasing expansion of Urban Heat Island (UHI) effects. This paper evaluates the microclimate beneﬁts due to cool road pavements, greenery, and photovoltaic canopies in a parking lot in Fondi (Italy), identifying the best strategy to counteract the negative effects of UHIs. The ENVI-met software allowed a microclimatic analysis of the examined area in July 2022 through the comparison of the thermal performances between the current asphalt pavement and ten alternative scenarios. The proposed layouts were investigated in terms of air temperature (AT), surface temperature (ST), mean radiant temperature (MRT), and predicted mean vote (PMV). The results showed that the existing asphalt pavement is the worst one, while the cool pavement integrated with vegetation provides appreciable beneﬁts. Compared to the current layout, a new scenario characterized by light porous concrete for carriageable pavements and sidewalks, concrete grass grid pavers for parking stalls, a 2-m-high border hedge, and 15-m-high trees implies reductions of AT above 3 ◦ C, ST above 30 ◦ C, MRT above 20 ◦ C, and a maximum PMV value equal to 2.2.


Introduction
In the early 1800s, the meteorologist Howard [1][2][3] observed in London that the urban air temperature was higher than that of the surrounding areas.Over the decades, the economic and social opportunities of cities have attracted people from rural areas [4].This phenomenon has contributed to reducing green and countryside areas and increasing facilities [5,6].The anthropization factor caused the increase in air pollution and fostered the development of Urban Heat Islands (UHIs) [7,8].In the last decades, the effects of the current global warming have exacerbated UHIs; new planning schemes are necessary to improve urban livability [9][10][11] with cost-effective measures.Indeed, urban artificial surfaces (e.g., roads, roofs, and buildings) over the day absorb solar radiation and store thermal energy; at night, heat energy is transferred to the atmosphere and causes a 1-3 • C air temperature increase [3,12].This is enhanced by the summer diurnal temperatures and affects the physical and psychological discomfort of citizens [13].Moreover, UHIs have a serious economic impact due to the energy consumption for cooling indoors [2,14].
According to [15,16], it is possible to counteract UHIs by means: • light and permeable road pavements to improve the heat transmission between air and buildings; • greenery and trees to realize urban green infrastructures (UGIs); • sustainable transport and mobility to reduce the negative effects s private vehicles or conventional transport; • evapotranspiration to decrease the heating of the local urban atmosphere; • urban ventilation to improve the heat exchange.
A recent Italian standard provided for mandatory measures to counter UHIs, cool pavement materials, at least 60% permeable surfaces, and green furniture should be designed for all public parking works [17].In this study, an existing parking lot in Fondi (Lazio, Italy) is modeled with the software ©2022 ENVI-met GmbH to gain its twin digital model.The survey area was chosen to conduct a preliminary assessment of the best sustainable redevelopment strategies for the site with a view towards future upgrades.The ENVI-Met software allows to recreate a real urban area and to evaluate its thermal conditions [18,19] through the return of reliable outputs in the real conditions [20,21].After a validation procedure by comparing actual microclimate data with software output data, the current layout was modified with permeable light pavements and soft engineering solutions to investigate their effectiveness in mitigating UHI.This article proposes to replace the current layout of the studied area with 10 different scenarios based on recent cool pavement technologies.This study is a useful tool in order to evaluate which strategy appears to be the most appropriate to counteract the significant climate changes.The results expressed in terms of thermal and comfort parameters (i.e., AT, ST, MRT, and PMV) show quantitatively the interventions in an urban context that can ensure a high level of well-being.

Materials and Methods
The increase in temperatures in urban areas is caused by the daytime thermal energy absorbed by artificial surfaces that is radiated during the night.This process is driven by both the albedo and emissivity of materials [3,14,15].Albedo is the ratio between the reflected energy and the incident energy over a unit area [22].It depends on: the material color and influences the surface temperature (ST), especially during the daytime [6,23,24], the wavelength of shortwave solar radiation, and the incident angles of variable direct solar radiation during the day [25].Emissivity is the ratio between the energy radiated by an object compared to that radiated by a black body.It affects the surface temperatures of pavements, especially during the night [6,23,26].In addition to the above two thermal properties, the conductivity (k) and thermal capacity (cp) also have an effect on the thermal response of an urban road pavement [23,27].Thermal conductivity affects ST; the greater the thermal conductivity, the lower the daytime ST, and the opposite occurs at night.High cp values imply a reduction of the maximum ST, whereas low values favor the increase of the minimum ST [28,29].However, k and cp cannot counteract UHI.
Therefore, the best two strategies are based on high albedo and emissivity building materials.The former relies on pavements with cool materials (e.g., limestone, light stone, and light concrete), the latter on permeable pavements to increase evapotranspiration and decrease the heating of the local urban atmosphere.Whatever the climate, cool materials could be effective, whereas porous pavements are suitable for warm temperate climates, such as in the studied parking lot.Three pavement materials were examined as an alternative to the existing asphalt:

•
Porous light concrete has a 15-25% void structure.The high porosity gives mechanical strengths lower than those of traditional concrete and requires periodical cleaning to avoid pores' occlusion [30].Large joint gaps between concrete blocks give permeable pavement as well [31].

•
Concrete grass grid pavers allow both the evaporation of rainwater and evapotranspiration of grass.They are suitable for parking lots, because their use implies a low bearing capacity and high roughness [30,32].

•
Stone pavers (e.g., limestone, basalt, and porphyry) are used in urban areas because of their aesthetic value.The blocks allow different layouts of the surfaces [33].
Table 1 synthesizes the pros and cons and the physical characteristics of the existing and the proposed building materials [34][35][36].The software © ENVI-met 5.0.3 was used for the microclimatic analysis, although it is not suitable for simulating an evaporative cooling effect of pervious pavements.Three input interfaces about the geometric, physical, and meteorological characteristics of the site permit processing three-dimensional (3D) simulation models.The results were analyzed with the Leonardo interface in terms of Air Temperature (AT), Surface temperature (ST), Mean Radiant Temperature (MRT), and Predicted Mean Vote (PMV) [37][38][39].The PMV predicts people's thermal comfort in steady-state conditions (Equation ( 1)).In this study, the reference man is 35 years old, 1.75 m tall, and weighs 75 kg [40,41]: where M is the metabolism rate, W is the external work, pa is the partial water vapor pressure (Pa), fcl is the surface area factor of clothing, tcl is the surface temperature of clothing (°C), hc is the convective heat transfer coefficient (W/(m 2 × K)), AT is the air temperature (°C), and tr is the radiant temperature (°C ).Three different conditions are defined for the PMV according to the range of values assumed: ideal conditions (IC) for values between slightly cool (−1) and slightly warm (+1), acceptable conditions (AC) for values between (−3, −1) and (1, 3), and critical conditions (CC) for values over ±3.
The MRT quantifies the effect of environmental radiation on the human body.It depends on the surface's emissivity and the shadows of the environment [42][43][44][45].ENVI-met calculates the MRT according to Equation (2): where N is the number of the surrounding surfaces, Ti is the temperature of the ith surface, and  → are the factors of view between the person and the whole surrounding environment.
The examined area is Archimede Rotunno Square in Fondi (Lazio, Italy; lat.41°21′12"-long.13°25′29").The model is composed of a grid of 40 ×3 0 × 30 with a resolution of 2 × 2 × 2 m (x, y, z).The model includes the central parking area (with six pink points that identify the receptors), an urban asphalt straight road on the right, two concrete buildings at the top and bottom of the image, and a green park on the left (Figure 1).The software © ENVI-met 5.0.3 was used for the microclimatic analysis, although it is not suitable for simulating an evaporative cooling effect of pervious pavements.Three input interfaces about the geometric, physical, and meteorological characteristics of the site permit processing three-dimensional (3D) simulation models.The results were analyzed with the Leonardo interface in terms of Air Temperature (AT), Surface temperature (ST), Mean Radiant Temperature (MRT), and Predicted Mean Vote (PMV) [37][38][39].The PMV predicts people's thermal comfort in steady-state conditions (Equation ( 1)).In this study, the reference man is 35 years old, 1.75 m tall, and weighs 75 kg [40,41] where M is the metabolism rate, W is the external work, pa is the partial water vapor pressure (Pa), fcl is the surface area factor of clothing, tcl is the surface temperature of clothing (°C), hc is the convective heat transfer coefficient (W/(m 2 × K)), AT is the air temperature (°C), and tr is the radiant temperature (°C ).Three different conditions are defined for the PMV according to the range of values assumed: ideal conditions (IC) for values between slightly cool (−1) and slightly warm (+1), acceptable conditions (AC) for values between (−3, −1) and (1, 3), and critical conditions (CC) for values over ±3.
The MRT quantifies the effect of environmental radiation on the human body.It depends on the surface's emissivity and the shadows of the environment [42][43][44][45].ENVI-met calculates the MRT according to Equation (2): where N is the number of the surrounding surfaces, Ti is the temperature of the ith surface, and  → are the factors of view between the person and the whole surrounding environment.
The examined area is Archimede Rotunno Square in Fondi (Lazio, Italy; lat.41°21′12"-long.13°25′29").The model is composed of a grid of 40 ×3 0 × 30 with a resolution of 2 × 2 × 2 m (x, y, z).The model includes the central parking area (with six pink points that identify the receptors), an urban asphalt straight road on the right, two concrete buildings at the top and bottom of the image, and a green park on the left (Figure 1).The software © ENVI-met 5.0.3 was used for the microclimatic analysis, although it is not suitable for simulating an evaporative cooling effect of pervious pavements.Three input interfaces about the geometric, physical, and meteorological characteristics of the site permit processing three-dimensional (3D) simulation models.The results were analyzed with the Leonardo interface in terms of Air Temperature (AT), Surface temperature (ST), Mean Radiant Temperature (MRT), and Predicted Mean Vote (PMV) [37][38][39].The PMV predicts people's thermal comfort in steady-state conditions (Equation ( 1)).In this study, the reference man is 35 years old, 1.75 m tall, and weighs 75 kg [40,41] where M is the metabolism rate, W is the external work, pa is the partial water vapor pressure (Pa), fcl is the surface area factor of clothing, tcl is the surface temperature of clothing (°C), hc is the convective heat transfer coefficient (W/(m 2 × K)), AT is the air temperature (°C), and tr is the radiant temperature (°C ).Three different conditions are defined for the PMV according to the range of values assumed: ideal conditions (IC) for values between slightly cool (−1) and slightly warm (+1), acceptable conditions (AC) for values between (−3, −1) and (1, 3), and critical conditions (CC) for values over ±3.
The MRT quantifies the effect of environmental radiation on the human body.It depends on the surface's emissivity and the shadows of the environment [42][43][44][45].ENVI-met calculates the MRT according to Equation (2): where N is the number of the surrounding surfaces, Ti is the temperature of the ith surface, and  → are the factors of view between the person and the whole surrounding environment.
The examined area is Archimede Rotunno Square in Fondi (Lazio, Italy; lat.41°21′12"-long.13°25′29").The model is composed of a grid of 40 ×3 0 × 30 with a resolution of 2 × 2 × 2 m (x, y, z).The model includes the central parking area (with six pink points that identify the receptors), an urban asphalt straight road on the right, two concrete buildings at the top and bottom of the image, and a green park on the left (Figure 1).The software © ENVI-met 5.0.3 was used for the microclimatic analysis, although it is not suitable for simulating an evaporative cooling effect of pervious pavements.Three input interfaces about the geometric, physical, and meteorological characteristics of the site permit processing three-dimensional (3D) simulation models.The results were analyzed with the Leonardo interface in terms of Air Temperature (AT), Surface temperature (ST), Mean Radiant Temperature (MRT), and Predicted Mean Vote (PMV) [37][38][39].The PMV predicts people's thermal comfort in steady-state conditions (Equation ( 1)).In this study, the reference man is 35 years old, 1.75 m tall, and weighs 75 kg [40,41]: where M is the metabolism rate, W is the external work, pa is the partial water vapor pressure (Pa), fcl is the surface area factor of clothing, tcl is the surface temperature of clothing (°C), hc is the convective heat transfer coefficient (W/(m 2 × K)), AT is the air temperature (°C), and tr is the radiant temperature (°C ).Three different conditions are defined for the PMV according to the range of values assumed: ideal conditions (IC) for values between slightly cool (−1) and slightly warm (+1), acceptable conditions (AC) for values between (−3, −1) and (1, 3), and critical conditions (CC) for values over ±3.
The MRT quantifies the effect of environmental radiation on the human body.It depends on the surface's emissivity and the shadows of the environment [42][43][44][45].ENVI-met calculates the MRT according to Equation (2): where N is the number of the surrounding surfaces, Ti is the temperature of the ith surface, and  → are the factors of view between the person and the whole surrounding environment.
The examined area is Archimede Rotunno Square in Fondi (Lazio, Italy; lat.41°21′12"-long.13°25′29").The model is composed of a grid of 40 ×3 0 × 30 with a resolution of 2 × 2 × 2 m (x, y, z).The model includes the central parking area (with six pink points that identify the receptors), an urban asphalt straight road on the right, two concrete buildings at the top and bottom of the image, and a green park on the left (Figure 1).The software © ENVI-met 5.0.3 was used for the microclimatic analysis, although it is not suitable for simulating an evaporative cooling effect of pervious pavements.Three input interfaces about the geometric, physical, and meteorological characteristics of the site permit processing three-dimensional (3D) simulation models.The results were analyzed with the Leonardo interface in terms of Air Temperature (AT), Surface temperature (ST), Mean Radiant Temperature (MRT), and Predicted Mean Vote (PMV) [37][38][39].The PMV predicts people's thermal comfort in steady-state conditions (Equation ( 1)).In this study, the reference man is 35 years old, 1.75 m tall, and weighs 75 kg [40,41]: where M is the metabolism rate, W is the external work, p a is the partial water vapor pressure (Pa), f cl is the surface area factor of clothing, t cl is the surface temperature of clothing ( • C), h c is the convective heat transfer coefficient (W/(m 2 × K)), AT is the air temperature ( • C), and t r is the radiant temperature ( • C).Three different conditions are defined for the PMV according to the range of values assumed: ideal conditions (IC) for values between slightly cool (−1) and slightly warm (+1), acceptable conditions (AC) for values between (−3, −1) and (1, 3), and critical conditions (CC) for values over ±3.
The MRT quantifies the effect of environmental radiation on the human body.It depends on the surface's emissivity and the shadows of the environment [42][43][44][45].ENVI-met calculates the MRT according to Equation (2): where N is the number of the surrounding surfaces, T i is the temperature of the ith surface, and F p→i are the factors of view between the person and the whole surrounding environment.
The examined area is Archimede Rotunno Square in Fondi (Lazio, Italy; lat.41 • 21 12long.13 • 25 29 ).The model is composed of a grid of 40 ×3 0 × 30 with a resolution of 2 × 2 × 2 m (x, y, z).The model includes the central parking area (with six pink points that identify the receptors), an urban asphalt straight road on the right, two concrete buildings at the top and bottom of the image, and a green park on the left (Figure 1).The base model (S0) describes the current layout, with asphalt carriageable pavements and porphyry sidewalks (Figure 2).The rugged areas are sandy soil with albedo equal to 0.25 and emissivity equal to 0.90.Six receptors (1-6 pink and red points in Figures 1 and 2, respectively) were in the parking area to conduct the analysis.As performed in previous studies carried out by the authors [46], S0 was validated by comparing the AT calculated in the six receptors with those measured by the authors with the wi-fi weather station SBS-WS-500 Steinberg Systems (wind speed: 0-50 m/s, wind speed accuracy: ± 10%, humidity: 10-99%, humidity accuracy: ±5% (between 20% and 90%; 0-45 °C), and air temperature: −40-+60 °C (outside), temperature accuracy: ± 1 °C).The comparison gave an average difference equal to 1.65 °C (the maximum value was 3.67 °C and the minimum one 0.08 °C).S0 presents the results in terms of the AT, MRT, and PMV consistent with the negative effects of UHIs; therefore, the authors propose to replace the current pavement with different layouts to improve microclimatic conditions (Table 2): x focuses on the sidewalk's pavements; x ranges between 1 and 3, varying the sidewalk material; • Case 2.x focuses on all the road pavements; x ranges between 1 and 3, varying the pavement material; The base model (S0) describes the current layout, with asphalt carriageable pavements and porphyry sidewalks (Figure 2).The rugged areas are sandy soil with albedo equal to 0.25 and emissivity equal to 0.90.The base model (S0) describes the current layout, with asphalt carriageable pavements and porphyry sidewalks (Figure 2).The rugged areas are sandy soil with albedo equal to 0.25 and emissivity equal to 0.90.Six receptors (1-6 pink and red points in Figures 1 and 2, respectively) were in the parking area to conduct the analysis.As performed in previous studies carried out by the authors [46], S0 was validated by comparing the AT calculated in the six receptors with those measured by the authors with the wi-fi weather station SBS-WS-500 Steinberg Systems (wind speed: 0-50 m/s, wind speed accuracy: ± 10%, humidity: 10-99%, humidity accuracy: ±5% (between 20% and 90%; 0-45 °C), and air temperature: −40-+60 °C (outside), temperature accuracy: ± 1 °C).The comparison gave an average difference equal to 1.65 °C (the maximum value was 3.67 °C and the minimum one 0.08 °C).S0 presents the results in terms of the AT, MRT, and PMV consistent with the negative effects of UHIs; therefore, the authors propose to replace the current pavement with different layouts to improve microclimatic conditions (Table 2): x focuses on the sidewalk's pavements; x ranges between 1 and 3, varying the sidewalk material; • Case 2.x focuses on all the road pavements; x ranges between 1 and 3, varying the pavement material; Six receptors (1-6 pink and red points in Figures 1 and 2, respectively) were in the parking area to conduct the analysis.As performed in previous studies carried out by the authors [46], S0 was validated by comparing the AT calculated in the six receptors with those measured by the authors with the wi-fi weather station SBS-WS-500 Steinberg Systems (wind speed: 0-50 m/s, wind speed accuracy: ±10%, humidity: 10-99%, humidity accuracy: ±5% (between 20% and 90%; 0-45 • C), and air temperature: −40-+60 • C (outside), temperature accuracy: ±1 • C).The comparison gave an average difference equal to 1.65 • C (the maximum value was 3.67 • C and the minimum one 0.08 • C).S0 presents the results in terms of the AT, MRT, and PMV consistent with the negative effects of UHIs; therefore, the authors propose to replace the current pavement with different layouts to improve microclimatic conditions (Table 2):

•
Case 1.x focuses on the sidewalk's pavements; x ranges between 1 and 3, varying the sidewalk material; • Case 2.x focuses on all the road pavements; x ranges between 1 and 3, varying the pavement material; • Case 3.x focuses on all the road pavements and adds green furniture or photovoltaic panels to the area; x ranges between 1 and 4, varying the layout.The choice of the proposed scenarios and layouts aims to identify the best combination to mitigate the effects of UHIs.Scenarios S1.x and S2.x focus the microclimate investigation on the effects of sidewalks and pavement, respectively.Scenarios S3.x investigate the positive effects of the renewal of both the sidewalks and the lane with cool materials and also with the addition of green surfaces and photovoltaic panels, which can make parking management more sustainable.
The microclimate analysis was conducted in July 2022, as it is the most severe month [46].The authors verified with a comparison with a 72-h simulation that a 48-h analysis is enough to reach numerical stability during the model spin-up phase (the maximum difference of PMV was 0.012, the maximum difference of AT was 0.097 • C, and the maximum difference of TMR was 0.155 • C).Therefore, a 48-h analysis was performed starting from 06.00 a.m. on 1 July 2022.Table 3 lists the meteorological input data [47].For each receptor and scenario, the AT, ST, MRT, and PMV were assessed every six hours as of 12:00 a.m. on 2 July 2022 until 6:00 p.m. on 3 July 2022.
The main purpose of this study is to identify the layouts able to improve the environmental conditions and guarantee physical well-being and thermal comfort perceived by individuals, especially during the daytime.

Results
The Results section is divided into four subsections, one for each case examined.In this way, it is possible to interpret in detail the benefits resulting from a targeted intervention in the study area (i.e., sidewalks, road pavement, UGI, and canopies).

Current Scenario (S0)
Table 4 lists the results of S0 in terms of the PMV, AT, and MRT.The daytime results highlight higher than 4 PMV values and higher than 57 • C MRT values that imply serious thermal stress and discomfort.However, the nighttime results are not critical: PMV is less than 0.7, and MRT and AT are about 18 • C and 25 • C, respectively.Figure 3a-d represents the AT, MRT, PMV, and ST map at 12.00 a.m. on 2 July, respectively.
Sustainability 2022, 14, x FOR PEER REVIEW 6 of 18 The main purpose of this study is to identify the layouts able to improve the environmental conditions and guarantee physical well-being and thermal comfort perceived by individuals, especially during the daytime.

Results
The Results section is divided into four subsections, one for each case examined.In this way, it is possible to interpret in detail the benefits resulting from a targeted intervention in the study area (i.e., sidewalks, road pavement, UGI, and canopies).

Current Scenario (S0)
Table 4 lists the results of S0 in terms of the PMV, AT, and MRT.The daytime results highlight higher than 4 PMV values and higher than 57 °C MRT values that imply serious thermal stress and discomfort.However, the nighttime results are not critical: PMV is less than 0.7, and MRT and AT are about 18 °C and 25 °C, respectively.Figure 3a-d  The maps in Figure 3 show critical conditions for most of the modeled surfaces.Indeed, the existing black pavement absorbs a significant amount of heat, a direct consequence of the low albedo and high heat capacity of the asphalt-wearing layer [48].

Case 1.x
Case 1.x focuses its attention on the pedestrian surfaces surrounding the parking The maps in Figure 3 show critical conditions for most of the modeled surfaces.Indeed, the existing black pavement absorbs a significant amount of heat, a direct consequence of the low albedo and high heat capacity of the asphalt-wearing layer [48].

Case 1.x
Case 1.x focuses its attention on the pedestrian surfaces surrounding the parking area.Porphyry pavers were substituted by concrete grass grid pavers (S1.1), light porous concrete (S1.2), and 5-cm-high grass (S1.3).Table 5 lists the results of Case 1.x in terms of the PMV, AT, and MRT.Whatever the hour, the PMV results do not differ significantly between the scenarios of Case 1.x (the minimum value is 3.89, 3.92, and 3.81 in S1.1-S1.3,respectively).Low differences are between S0 and Case 1.x over the nighttime (the average value of the PMV is 0.27 in S0, 0.04 in S1.1, and 0.03 in S1.2 and S.13).Regarding AT, at 12.00 on 2 July, the AT ranges between 31.51 • C of S1.1 and 33.22 • C of S1.3.S1.1 and S1.2 during the daytime have a similar trend that is better than S0 (at 12.00, AT in S0 ranges between 32.39 • C and 33.99 • C).At 12.00 a.m., both the grass grid pavers in S1.1 and the porous concrete in S1.2 imply a 1 • C AT reduction compared to S0 (the average AT values are 32.43 • C and 32.45, respectively, against 33.57• C of S0).It should be noted that the software does not allow simulations of the evaporative cooling effect of pervious pavements; the results are worse than they should be.S1.3 gives slightly worse results (the average AT is 32.80 • C).At midday, the MRT assumes high values both in S0 and Case 1.x (the minimum value is 57.52 • C in S0, 60.17 • C, 60.87 • C, and 57.18 • C in S1.1-S1.3,respectively).S1.1 and S1.2 give the worse results than S0, while S1.3 shows small improvements due to the sidewalk's grass.During the nighttime, both S0 and Case 1.x have absolute low values whose trends are comparable to the daytime results.
Figure 4a-d shows the PMV map of S0 and S1.1-S1.3,respectively, at 12.00 a.m. on 2 July.At midday, the minimum and maximum PMV values of Case 1.x range between 2.72 and 5.03 of S1.1, 2.76 and 5.06 of S1.2, and 2.58 and 4.99 of S1.3.This last scenario ensures the best performance compared to S0, whose minimum and maximum PMV values are 2.66 and 5.28, respectively.The results highlight that replacing porphyry sidewalks with porous concrete pavements or concrete grass grid pavers brings about a negligible benefit.The small extension of the modified surface justifies these results.
respectively, against 33.57°C of S0).It should be noted that the software does not allow simulations of the evaporative cooling effect of pervious pavements; the results are worse than they should be.S1.3 gives slightly worse results (the average AT is 32.80 °C).At midday, the MRT assumes high values both in S0 and Case 1.x (the minimum value is 57.52 °C in S0, 60.17 °C, 60.87 °C, and 57.18 °C in S1.1-S1.3,respectively).S1.1 and S1.2 give the worse results than S0, while S1.3 shows small improvements due to the sidewalk's grass.During the nighttime, both S0 and Case 1.x have absolute low values whose trends are comparable to the daytime results.At midday, the minimum and maximum PMV values of Case 1.x range between 2.72 and 5.03 of S1.1, 2.76 and 5.06 of S1.2, and 2.58 and 4.99 of S1.3.This last scenario ensures the best performance compared to S0, whose minimum and maximum PMV values are 2.66 and 5.28, respectively.The results highlight that replacing porphyry sidewalks with porous concrete pavements or concrete grass grid pavers brings about a negligible benefit.The small extension of the modified surface justifies these results.

Case 2.x
Case 2.x modifies both sidewalk and parking pavements.Concrete grass grid pavers and porous light concrete are the overall pavements in S2.1 and S2.2, respectively.S2.3 has concrete grass grid pavers for stalls and porous light concrete for the other road surfaces.Table 6 lists the results of Case 2.x in terms of the PMV, AT, and MRT.
The best technical and environmental scenario is S2.3.Indeed, during the daytime, road materials with high albedo and emissivity contribute to reducing both the AT and PMV compared to S0 (average reduction of 0.88 • C and 0.37, respectively); at 6.00 p.m. on 2 July PMV is near the comfort zone (i.e., 2.15).Nevertheless, the average MRT value is high both at 12.00 a.m. and 6.00 p.m. (54.54 • C and 37.88 • C, respectively).Figure 5a-d shows the PMV map of S0 and S2.1-S2.3,respectively, at 12.00 on 2 July.
S2.1 has the best PMV values of Case 2.x (the average PMV is 3.61 at 12.00 on 2 July).From an environmental perspective, S2.1 is the most suitable option, but concrete grass grids make up a discontinuous pavement, resulting in discomfort for pedestrians or light vehicles.Therefore, S2.3 is preferred, because its average PMV is 3.76 at 12.00 on 2 July compared to 3.91 of S2.2.
Case 2.x partly transposes [17], because all the road surfaces are permeable and cool.The results are better than Case 1.x, but they are not enough to guarantee a favorable state of comfort or to mitigate the UHI.S2.1 has the best PMV values of Case 2.x (the average PMV is 3.61 at 12.00 on 2 July).From an environmental perspective, S2.1 is the most suitable option, but concrete grass grids make up a discontinuous pavement, resulting in discomfort for pedestrians or light vehicles.Therefore, S2.3 is preferred, because its average PMV is 3.76 at 12.00 on 2 July compared to 3.91 of S2.2.
Case 2.x partly transposes [17], because all the road surfaces are permeable and cool.The results are better than Case 1.x, but they are not enough to guarantee a favorable state

Case 3.x
Case 3.x fully transposes [17], because it adds green coverage for at least 10% of the gross parking area, not less than a 1-m-high boundary hedge, and any photovoltaic canopies above the stalls.Figure 6a-d   Table 7 lists the results of Case 3.x in terms of the PMV, AT, and MRT.Table 7 lists the results of Case 3.x in terms of the PMV, AT, and MRT.The green furniture in S3.3 guarantees thermal comfort, because the average PMV decreases to 2.25 at 12.00 a.m. and 1.21 at 6.00 p.m.The photovoltaic canopies in S3.4 shadow the area, reducing the ST and leading to an average PMV value of 2.68 at 12.00 a.m.According to Tables 6 and 7, at night, there is a slight deterioration in terms of the AT and PMV, because the trees are a barrier and retain the heat of the day under their foliage.At 00.00 a.m. and 6.00 a.m., S3.4 is the best solution (the average AT is 24.The green furniture in S3.3 guarantees thermal comfort, because the average PMV decreases to 2.25 at 12.00 a.m. and 1.21 at 6.00 p.m.The photovoltaic canopies in S3.4 shadow the area, reducing the ST and leading to an average PMV value of 2.68 at 12.00 a.m.According to Tables 6 and 7, at night, there is a slight deterioration in terms of the AT and PMV, because the trees are a barrier and retain the heat of the day under their foliage.At 00.00 a.m. and 6.00 a.m., S3.4 is the best solution (the average AT is 24.47 °C and 23.55 °C, respectively, against 24.58 °C and 23.65 °C of S3.3).The average PMV is almost neutral, equal to −0.02 and 0.06, respectively, against 0.39 and 0.33 of S3.3).However, the trees contribute to the drastic diurnal reduction of MRT; the average MRT at 12.00 a.m. on 2 July reaches 57.82 °C in S0, while it is 53.64 °C in S3.1, 50.31 °C in S3.2, and 37.80 °C in S3.3.Overall, the daytime benefits of trees far outweigh the disadvantages of the nighttime hours.The average MRT value of 3.4 at 12.00 a.m. is 46.02 °C; the performance of the layout with canopies is intermediate between the current scenario and those with green furniture.Figure 8a-d shows the absolute difference between MRT in S0 and S3.1-S3.4,respectively, at 12.00 on 2 July.The results confirm studies in the literature where dense and strategically arranged trees reduced the MRT, especially in open sites [49] and canopy shade and reduced the direct radiation, offering benefits against heat stress [50].Figure 9a-d   The results confirm studies in the literature where dense and strategically arranged trees reduced the MRT, especially in open sites [49] and canopy shade and reduced the direct radiation, offering benefits against heat stress [50].Figure 9a-d   The ST maps in Figure 9 highlight the pivotal role of trees and shade to reduce ST.At midday, in S0, the maximum ST value is 59.4 °C (Figure 9a), whereas it is 55.61 °C, 52.23 °C, and 52.57°C in S2.3, S3.3, and S3.4,respectively.In particular, the presence of shaded areas is also beneficial for the surrounding areas, as confirmed by the ST trend of the road on the east side of the model.

Discussion
In this manuscript, the authors proposed an application of recent innovations in UHI mitigation to a real case of study.In detail, the area examined was a parking lot in the City of Fondi (Lazio, Italy).The implementation of the current parking lot conditions in ENVI-Met software demonstrated the presence of adverse microclimatic conditions.Therefore, in this study, several useful scenarios were proposed to foster and ensure better living conditions for humans.They differed from each other in the gradual replacement of the current conditions, so that improvements from the introduction of a particular cool strategy could be read in detail.The results were analyzed in terms of the AT, MRT, ST, and PMV and demonstrated in accordance with the scientific literature the benign effects associated with the introduction of cool material and UGIs [51][52][53].
Figures 7-9 demonstrate that S3.3 gives satisfactory results, because it is possible to achieve the objectives of reducing temperatures and ensuring PMV in the comfort zone during the daytime.Moreover, this solution is sustainable due to the presence of large trees and permeable road pavements [54].According to recent studies, this article enhances the cooling performance of permeable pavements [55,56] and green furniture in an urban context [57,58].Conversely, the absence of trees in S3.4 turns the alternative less

Discussion
In this manuscript, the authors proposed an application of recent innovations in UHI mitigation to a real case of study.In detail, the area examined was a parking lot in the City of Fondi (Lazio, Italy).The implementation of the current parking lot conditions in ENVI-Met software demonstrated the presence of adverse microclimatic conditions.Therefore, in this study, several useful scenarios were proposed to foster and ensure better living conditions for humans.They differed from each other in the gradual replacement of the current conditions, so that improvements from the introduction of a particular cool strategy could be read in detail.The results were analyzed in terms of the AT, MRT, ST, and PMV and demonstrated in accordance with the scientific literature the benign effects associated with the introduction of cool material and UGIs [51][52][53].
Figures 7-9 demonstrate that S3.3 gives satisfactory results, because it is possible to achieve the objectives of reducing temperatures and ensuring PMV in the comfort zone during the daytime.Moreover, this solution is sustainable due to the presence of large trees and permeable road pavements [54].According to recent studies, this article enhances the cooling performance of permeable pavements [55,56] and green furniture in an urban context [57,58].Conversely, the absence of trees in S3.4 turns the alternative less "green" but qualifies the proposed scenario as the best option from an energy point of view.Indeed, the produced electricity can be used to recharge electric or plug-in hybrid vehicles.Therefore, the authors conducted the energy analysis of S3.4 based on the following assumptions:

•
On average, 7.2 m 2 of solar cells are necessary to build a 1-kW power plant if they are correctly positioned and tilted.In S3.4, the cells were horizontal; thus, the efficiency of energy production was reduced by a factor of 0.75 [59]; • A factor of 0.8 takes into account the system losses [60]; The overall cell surface is 1500 m 2 .
According to [61], the annual solar radiation on the horizontal plane for Latina, a city near Fondi, is 1673 kWh/m 2 .Therefore, according to [62], it is possible to value the theoretical annual gain G of the plant, which is equal to 20,326.95kWh.Since an electric car consumes, on average, 15 kWh/100 km [63], the energy produced by the photovoltaic canopies is enough to travel 120,906 km/year.Since 60 stalls are in the parking area, each car parked during the year can recharge its batteries and travel about 2000 km.Therefore, S3.4 would create new favorable solutions for the Italian energy market to reduce the dependence on fossil fuels and promote carbon-neutral mobility.
The analysis focused on physical (air temperature, surface temperature, and mean radiant temperature) and thermal-physiological (predicted mean vote) variables, but structural issues cannot be overlooked [64,65].The results showed that the thermophysical properties of building materials play a pivotal role in improving the quality of life.Finally, even during the hottest hours, the inclusion of UGIs and photovoltaic canopies boosted the benefits of cool pavement, favoring the reduction of thermal parameters and increasing human comfort.

Conclusions
Traditional black and low-permeable road asphalt pavements contribute to UHIs, because the wearing material has low albedo and emissivity and a high thermal capacity.They overheat and absorb heat from the sun in the daytime and radiate it out as the temperature drops.The negative thermophysical effects overlap with those from climate change and require mitigation strategies.Cool materials and green furniture improve livability in the urban environment, because they reduce both the ST and AT and allow evapotranspiration.
With ENVI-Met, a 3D twin digital model of a parking lot in Fondi (Lazio, Italy) was modeled.According to the Italian Ministry of the Environment (2017), the current lowpermeable pavement was replaced with a permeable one and green furniture was added in ten alternative scenarios.The microclimate of the examined area was described by the air temperature, surface temperature, mean radiant temperature, and PMV in the hottest month of the year.The results showed that the best scenarios from a technicalenvironmental point of view have pavements composed of grass concrete grids and light permeable concrete, respectively, for parking stalls and carriageable areas.Indeed, high albedo and emissivity reduce the AT (e.g., at 12.00 a.m.AT is 32.69 • C in S2.3 compared to 33.57• C in S0) and ensure thermal comfort (at 12.00 a.m.PMV is 3.76 in S2.3 compared to 4.13 S0), but they are not enough to counteract the effects of UHIs.Therefore, green furniture composed of trees and hedges has been added to the area; they shade surfaces, reducing at 12.00 a.m. both the AT (there is a difference of over 3 • C between S3.3 and Case S0 at 30.23 • C vs. 33.57• C) and MRT (37.80 • C of S3.3 vs. 57.82• C of S0).S3.3 is the best scenario, as the main objective (i.e., mitigation of the heat island in the hottest hours) is achieved with soft engineering strategies (i.e., greenery and permeable pavements) that are compliant with the current Italian standards.Finally, a scenario with photovoltaic shelters covering the parking stalls was modeled (S3.4).The thermal and environmental results were appreciable during the day (at 12.00, the PMV and AT were 2.68 and 29.77 • C, respectively, compared to 4.13 and 33.57• C of S0).Case 3.4 not only shows thermal and comfort benefits but also foreshadows the benefits associated with this strategy.The incorporation of photovoltaic canopies in the parking area enables sustainable power generation for public destinations and answers the rapid growth in e-mobility.
The results showed the great benefits from the implementation of the strategies proposed to counteract and mitigate the effects of UHIs.The use of cool pavements, greenery and canopies returned appreciable results in urban public spaces whose redesigns can ensure a better quality of life.This case study is a useful tool to identify the best technology to oppose UHIs and extend the chosen methodology to other real-world cases.In the future, further studies will be carried out to improve the proposed technologies and identify even more efficient solutions to slow climate change and environmental degradation.

Table 7 .
Results of Case 3.x in terms of the PMV, AT, and MRT.

Table 7 .
Results of Case 3.x in terms of the PMV, AT, and MRT.
47 • C and 23.55 • C, respectively, against 24.58 • C and 23.65 • C of S3.3).The average PMV is almost neutral, equal to −0.02 and 0.06, respectively, against 0.39 and 0.33 of S3.3).However, the trees contribute to the drastic diurnal reduction of MRT; the average MRT at 12.00 a.m. on 2 July reaches 57.82 • C in S0, while it is 53.64 • C in S3.1, 50.31 • C in S3.2, and 37.80 • C in S3.3.Overall, the daytime benefits of trees far outweigh the disadvantages of the nighttime hours.The average MRT value of 3.4 at 12.00 a.m. is 46.02 • C; the performance of the layout with canopies is intermediate between the current scenario and those with green furniture.Figure 7a-d shows the PMV absolute difference between S0 and S3.1-S3.4,respectively, at 12.00 on 2 July.Sustainability 2022, 14, x FOR PEER REVIEW 12 of 18 Figure 7a-d shows the PMV absolute difference between S0 and S3.1-S3.4,respectively, at 12.00 on 2 July.
represents ST maps of S0, S2.3, S3.3, and S3.4,respectively, at 12.00 on 2 July.The ST maps in Figure9highlight the pivotal role of trees and shade to reduce ST.At midday, in S0, the maximum ST value is 59.4 • C (Figure9a), whereas it is 55.61 • C, 52.23 • C, and 52.57• C in S2.3, S3.3, and S3.4,respectively.In particular, the presence of shaded areas is also beneficial for the surrounding areas, as confirmed by the ST trend of the road on the east side of the model.

Table 1 .
Pros and cons of the examined building materials.

Table 1 .
Pros and cons of the examined building materials.

Table 1 .
Pros and cons of the examined building materials.

Table 1 .
Pros and cons of the examined building materials.

Table 1 .
Pros and cons of the examined building materials.

Table 2 .
Characteristics of the examined scenarios.Light porous concrete for carriageable pavements and sidewalks, and concrete grass grid pavers for stalls + 2-m-high boundary hedge around the area + photovoltaic canopies over the parking stalls

Table 4 .
Results of S0 in terms of the PMV, AT, and MRT.

Table 4 .
Results of S0 in terms of the PMV, AT, and MRT.

Table 5 .
Results of Case 1.x in terms of the PMV, AT, and MRT.

Table 6 .
Results of Case 2.x in terms of the PMV, AT, and MRT.