Natural Radioactivity Measurements and Radiological Hazards Evaluation for Some Egyptian Granites and Ceramic Tiles

: All over the world, people widely use granites and ceramic tiles in their residential establishments. Information concerning the radiological properties of such materials reveals how to ensure the sustainability of their safe use in terms of these properties. In the present work, the distribution of the terrestrial radioisotopes U-238 (Ra-226), Th-232, and K-40 for 23 different brands of Egyptian commercial granites and ceramic tiles samples (widely used domestically and exported) was determined using gamma radiation spectroscopy. This process pinpoints the possible radiological health risks related to gamma ray exposure and radon gas resulting from the use of these materials indoors. The concentration values of the aforementioned radioisotopes in the examined samples were compared to the corresponding global average values (GAVs) of the UNSCEAR and to those available in other countries. The overall average concentrations for U-238, Th-232, and K-40 in the total samples were observed to be 46.17 ± 2.81 (less than its GAV), 51.65 ± 2.35 (slightly above its GAV), and 701.62 ± 40.60 Bq/kg (1.4 times greater than the GAV), respectively. The related radiological parameters and indices were calculated and compared to the prescribed limits set by commissions and organizations concerned with radiation protection (the WHO, ICRP, UNSCEAR, and EC) to ensure the safe use of the investigated granites and ceramic tiles. The assessed indices and parameters fall within the recommended values and safety limits. In conclusion, there is no risk from using the granites and ceramic tiles under investigation in residential facilities.


Introduction
For humans, exposure to natural ionizing radiation is unavoidable. Exposure arises primarily from both terrestrial and cosmogenic radioisotopes. Terrestrial radioisotopes (K-40, U-238, and Th-232) exist naturally in all different environmental media, including air, water, food, soil, rock, building materials, etc. [1][2][3]. The existence of the abovementioned radioisotopes in building materials is responsible for delivering about 85% of the radiation dosage to the world's population [3,4]. Accordingly, providing information on terrestrial radioisotope concentrations and distributions in building materials is essential and it is required to monitor contamination originating from their radioactivity in residential environments.
The natural radioactivity level in building materials is confined in the terrestrial radionuclide concentrations in the geological materials from which they are derived [4,5], i.e., it varies according to the geological origin and geochemical characteristics of the constituent materials. Additionally, the radiation dose received is controlled by several factors, including residences places ventilation, and kinds [1].
In fact, gamma rays and radon gas (Rn-222 and Rn-220) are the most significant products of the terrestrial radioisotopes' radioactivity in building materials, in light of the A total of 107 tile samples (42 granite samples plus 65 ceramic samples) from 23 different brands were purchased from Egyptian building materials markets and suppliers. The commercial ceramics and granites studied are among the best widely used decorative building materials brands in Egypt. Before transporting the samples to the lab, they were properly catalogued, labeled, and named according to their popular names known in both the global and domestic markets (Table 1). More detailed information, particularly for granite, is available at (www.stonecontact.com, accessed on 19 June 2022). The samples have been given identification numbers in brackets, which are (1 to 42) for granites, and (43 to 107) for ceramic tiles. Then, each sample was individually ground to a powder, to avoid contamination between samples, and sieved through a sieve (200 µm mesh). All the samples were oven-dried for 5 h at 105 • C to remove the moisture content. These prepared samples were subsequently weighed (between 600 g and 850 g) and sealed in plastic cylindrical beakers (48 mm radius, 82 mm height, and 0.5 mm thickness) for more than 4 weeks to guarantee access to the secular equilibrium between parent radioisotopes and daughters in the natural disintegration series ( 232 Th and 238 U).

Gamma Spectrometric Analysis
To measure the activity concentrations of the radioisotopes (γ-emitters) in the samples, a low-background γ-rays spectroscopy system consisting of a semiconductor HPGe (Hyper-Pure Germanium) detector (Model GR4020, Canberra, Meriden, CT, USA) with a 40% relative efficiency and energy resolution (FWHM) of 2 keV at the 1332 keV γ-line (Co-60) was used. In addition, the system contains a suitable lead shield (Model 747E, Canberra, USA) surrounding the detector to prevent more than 98% of the external background radiation from reaching the detector during the analysis. The gamma spectrums were acquired and analyzed utilizing the Genie-2000 software (Version 3.3, Canberra, USA) [40] coupled with a multichannel analyzer (Model DAS-1000, Canberra, USA). For calibrating the detector's energy and efficiency, the LabSOCS (Laboratory Sourceless Calibration Software) designed using the features of geometry composer and gamma analysis within the Genie-2000 software, was used. The Genie-2000 software also contains the detector's characterization files created based on the system manufacturer's fundamental calibration tests (Canberra). To authenticate the efficiency data provided by LabSOCS, measurements were completed in our laboratory with a set of gamma calibration sources (Co-60, Cs-137, Ba-133, Mn-54, Zn-65, and Na-22), which revealed a significant agreement (90%) between empirical and mathematical peak efficiency.
Each prepared sample was put on the detector for a time period no less than 12 h in order to obtain an accurate counting statistic for gamma lines (photo-peaks) of importance. Additionally, the background level in the laboratory was measured using an empty beaker in similar conditions. The K-40 radionuclide was determined directly by its own gamma line intensity (1460.8 keV). As for U-238 (Ra-226), it was specified through its progeny Bi-214 (1764.5, 1120.3, and 609.3 keV) and Pb-214 (351.9 and 295.2 keV). On the other hand, Th-232 was identified via its daughters Ac-228 (968.9, 911.2, and 338.3 keV), Tl-208 (2614.5 and 583.2 keV), and Pb-212 (238.6 keV). The activity concentration (AC) and the uncertainty in activity concentration (U AC ) of the previously mentioned radionuclides in each sample were calculated from their corresponding gamma line intensities taking into account the sample mass, counting time, gamma decay transition probabilities, and detector efficiencies [41][42][43].

Activity Concentrations Estimation
The activity concentration (AC) in the granites and ceramic tiles samples under investigation was estimated as follows [41]: where N c,E is the net count rate resulting from subtracting the count rate of the peak at energy E in the sample spectrum minus that of the background spectrum at the same energy E, P γ,E denotes the probability of emitting gamma radiation with energy E for the radioisotope of interest, ε E is the detector absolute efficiency at energy E, and M s refers to the sample mass. Moreover, using the equation below, the uncertainty in activity concentration, U AC , was calculated based on uncertainties in N c,E , P γ,E , ε E , and M s [43]:

Estimation of Radiological Risks
For understanding the effect of radiological hazards on human health when using the investigated granites and ceramic tiles as tiling materials in buildings, several radiation hazard indices were estimated. The radium equivalent activity (Ra eq ), gamma index (I γ ), indoor absorbed gamma dose rate (D in ), yearly effective gamma dose rate (E in ), and excess lifetime cancer risk (ELCR) were used to investigate gamma radiation risks, while the alpha index (I α ), radon exhalation rate (RX), radon concentration (C Rn ), and yearly effective dose due to radon (E Rn ) were evaluated in order to investigate the potential radon risks.

Radium Equivalent Activity (Ra eq )
The Ra eq is one of the most effective radiological indices for determining gamma radiation hazards due to the radioisotopes K-40, U-238 and Th-232 content in tiling materials, considering the non-uniform distribution of these radioisotopes in matter. As per Beretka et al. [44], Ra eq is described by the following equation: where AC U , AC Th , and AC K are the specific activity concentrations of the radioisotopes U-238 (Ra-226), Th-232, and K-40, respectively. In fact, the Ra eq reflects the weighted total of the abovementioned three radioisotopes' concentrations within materials under the premise that gamma dose rates from 4810 Bq/kg of K-40, 259 Bq/kg of Th-232, and 370 Bq/kg of U-238 (Ra-226) are almost equal. From a radiation protection perspective, the ceramic and granite tiles studied herein are safe provided that their Ra eq levels are not above 370 Bq/kg [44] (permissible limit) corresponding to a yearly effective dosage of 1.5 mSv [41,45].

Gamma Index (I γ )
The I γ is taken into consideration as a monitoring tool specifying whether construction materials are safe to use or not. Considering that the external exposure due to gamma radiation from the tiling (superficial or covering) materials has a limit of 1 mSv/year, the I γ is adopted by the European Commission [46] to be estimated via the following equation: According to the European Commission [46], for covering materials such as the ceramic and granite tiles under investigation, if they have a I γ ≤ 2, this leads to an increase in the annual gamma dose rate with an amount ≤ 0.3 mSv/y resulting from these materials. In other words, these materials fall within the exemption level for building materials from all limitations about their radioactivity. Furthermore, if materials achieve criteria 2 < I γ ≤ 6, they will contribute to the annual gamma dose rate with an amount ≤ 1 mSv/y and fall within the recommended action level. Eventually, materials with I γ > 6 are not suitable for safe use in buildings [46].

Indoor Absorbed Gamma Dose Rate (D in ) and Yearly Effective Dose (E in )
Estimation of the indoor absorbed gamma dose rate (D in ) and its associated yearly effective dose (E in ) are significant mechanisms for determining the external exposure caused by terrestrial radioisotopes (Th-232, U-238, and K-40). According to the European Commission [46], Equations (5) and (6) can be used to estimate the D in and E in in the air within rooms as a result of using the investigated granites and ceramic tiles as superficial construction materials: where F 1 (=0.7 Sv/Gy), F 2 (=0.8), and F 3 (=8766 h) represent the conversion factor from the absorbed dose to the effective dose in the air, indoor residency factor, and hours of the year, respectively.

Excess Lifetime Cancer Risk (ELCR)
The ELCR is an important quantity through which the incidence of cancer for an individual exposed to a low gamma radiation dose over their lifetime (66-years) can be figured out. Depending on the E in incurred by individuals from the studied ceramic and granite tiles (superficial building materials) when used in buildings, the ELCR can be estimated as follows [4,41]: where C 1 (=66 y [47]) and C 2 (=0.05 Sv −1 for the general population) stand for life expectancy on average and fatal cancer risk, respectively [42,48].

Alpha Index (I α )
The I α given by the equation below [41] is used for estimating the risk of exposure to internal alpha radiation owing to the inhalation of radon. The estimation of I α is fundamentally dependent on the U-238 (Ra-226) activity concentration (AC Ra ) in construction materials, considering that materials with a concentration of 226 Ra < 200 Bq kg −1 cannot emit an indoor radon concentration >200 Bq m −3 , i.e., these materials come within the range of the recommended action level of indoor radon exposure for buildings, as previously agreed upon by the European Commission [46] and ICRP [49].

Radon Concentration (C Rn ) and Yearly Effective Dose Resulting Therefrom (E Rn )
In this study, the parallelepiped room model (4 × 5 × 2.8 m) is taken into account to assess the concentration of radon and the associated absorbed dose rate delivered to residents, assuming the floor is made of the investigated ceramic or granite tiles. Thus, Equation (9) is applied, according to the European Commission [46], to determine the increase in indoor radon concentration (C Rn ) brought on by the radon exhalation rate (RX) from the investigated ceramic or granite tiles used in buildings: , and V [m 3 ] represent the radon exhalation rate per unit area, Ra-226 decay constant, ventilation rate, tiled floor surface, and volume of the room, respectively. Based on the determined Ra-226 concentration (AC Ra ), Equation (10) can be applied to estimate the RX for the investigated tiles with thickness d (=3 cm and 1 cm for granites and ceramic tiles, respectively), density ρ (=2600 kg/m 3 ), and emanation coefficient η (=0.45), as reported in Refs. [20,41,50]: It is worth noting that the room ventilation rate (λ o ) was chosen with 0.5 h −1 for normal ventilation and 0.1 h −1 for poor ventilation. [9,41]. Furthermore, the (S/V) ratio of the room surface tiled with the investigated ceramic and granite tiles was chosen to be 2 m −1 [41].
As per the UNSCEAR [6] report, the yearly effective dose (E Rn ) that dwellers obtain from the indoor radon concentration (C Rn ) was estimated by the following formula: where C 1 (=9 nSv per Bq m −3 h), C 2 (=0.8), and C 3 (=0.4) stand for the factors of dose conversion, dwellers' indoor residency, and equilibrium equivalent radon concentration indoors, respectively [6,51].

Results and Discussion
4.1. Radioisotope ( 238 U, 232 Th, and 40 K) Concentrations Table 2 displays the ranges and averages, as well as standard errors, for the estimated concentrations values of U-238 (Ra-226), Th-232, and K-40 in the granites and ceramic tiles collected. Furthermore and by way of illustration, Figure 1 depicts the variations of the abovementioned radioisotopes concentrations in the samples under examination. Evidently, Figure 1 and Table 2 show that the concentrations of the considered radioisotopes fluctuate from 8. 40    Regarding the mean values of the radioisotope concentrations inserted in Table 2 and plotted in Figure 2, it is clear that CVE samples contain the lowest mean concentrations of both K-40 and Th-238, with levels of 269. 36   Regarding the mean values of the radioisotope concentrations inserted in Table 2 and plotted in Figure 2, it is clear that CVE samples contain the lowest mean concentrations of both K-40 and Th-238, with levels of 269. 36  plotted in Figure 2, it is clear that CVE samples contain the lowest mean concentrations of both K-40 and Th-238, with levels of 269.36 ± 13.15 and 32.96 ± 1.94 Bq/kg, respectively, while GBiHa samples have the lowest mean concentration of U-238 with a level of 16.95 ± 4.90 Bq/kg. In contrast, GRSS samples appear to have the highest mean concentrations of both U-238 and Th-232, with levels of 174.55 ± 11.38 and 131.07 ± 5.20 Bq/kg, respectively, whereas, GBrHu samples have the highest mean concentration of K-40, with a level of 1695.38 ± 37.21 Bq/kg.    Table 2 also display the mean values of the aforementioned radioisotope concentrations in the materials under investigation against their corresponding global average values (GAVs) in building materials as given by the UNSCEAR [52]. Notably, the GAVs for U-238, Th-232, and K-40 in building materials are 50, 50, and 500 Bq/kg, respectively, according to the UNSCEAR [52]. Apparently, the mean concentration of U-238 in all granites and ceramic tiles samples herein, except for GBrHu, GKG, GRHL, GRSS, and GRN samples, is lower than its GAV of 50 Bq/kg in building materials [52], (Figure 2 and Table 2). Similarly, the average concentration of Th-232 in the investigated samples, except for the GBrHu, GNA, GRAD, GRHL, GRAS, GRSS, GRA, GRN, GRF, and CAR samples, is lower than its GAV in building materials of 50 Bq/kg [52]. However, the average concentration of K-40 for all of the granite and ceramic brands, except for the CAL, CCL, CGL, CPH, CRO, and CVE samples, is greater than the GAV (500 Bq/kg) of building materials [52], (Figure 2 and Table 2).
The overall average concentrations for U-238, Th-232, and K-40 of the total samples were observed to be 46.17 ± 2.81 (less than its GAV), 51.65 ± 2.35 (slightly above its GAV), and 701.62 ± 40.60 Bq/kg (1.4 times greater than the GAV), respectively, as demonstrated in Table 2 and Figure 2. Moreover, in all of the investigated brands' samples ( Figure 2), the K-40 concentration is the greatest among the concentrations of the three studied radionuclides, as the granites contain about 33% potash feldspar minerals [21]. Moreover, it was found that the K-40 concentration is the largest contributor to the total concentration for all samples (Figure 3). Both U-238 and Th-232 contribute roughly the same percentage (6%), to the overall concentration of samples, while K-40 contributes a larger percentage (88%), as shown in Figure 3.  A comparison between the radioactivity levels in the studied samples and those in other previous relevant studies on granites and ceramics used in Egypt and other countries is illustrated in Table 3. From Table 3, one can deduce that many of the data from the relevant literature are comparable to our findings. This can be confirmed using the den- A comparison between the radioactivity levels in the studied samples and those in other previous relevant studies on granites and ceramics used in Egypt and other countries is illustrated in Table 3. From Table 3, one can deduce that many of the data from the relevant literature are comparable to our findings. This can be confirmed using the dendrogram (Figure 4) derived from the hierarchical cluster analysis (HCA) based on the three variables (U-238, Th-232, and K-40 concentrations). In HCA, the cluster method between-groups linkage is used coupled with the square Euclidean distance. Accordingly, the countries in which the studies were accomplished have been divided into homogeneous groups based on the similarity in concentrations of the three radionuclides (U-238, Th-232, and K-40) (Figure 4). Figure 4a shows that the Egyptian granite tiles studied herein come close to the granites used in Bangladesh [22] and Nigeria [2] in terms of the content of the three aforementioned radionuclides, as they were grouped into a homogeneous group. However, they are far from those used in Pakistan [25], as illustrated in Figure 4a. Likewise, Figure 4b exhibits that the ceramic tiles examined herein are matched to the ceramics used in Italy [23] and Egypt [30] but are very different to those used in Poland [37], Serbia [9], and Nigeria [2] in terms of radionuclide content.  Evidently, in many of the investigated granite and ceramic samples, the radioisotopes' displayed concentrations were more elevated than the GAVs (Figure 2). For instance, in granites of "Rosa Sardo Sinai" (GRSS) samples, concentrations of uranium, thorium, and potassium exceed their corresponding GAVs by about three times, confirming the previous study on the granite of the Sinai area by Fares [39]. Therefore, it was crucial to assess the likely radiological risks to peoples' health owing to the use of these materials in buildings. Table 4 displays some of the evaluated radiological variables for the granite and ceramic samples under consideration. Through the estimated Req, Iγ, Din, Ein, and ELCR (Table 4), the gamma ray hazards posed by the materials under investigation when used as tiling in buildings can be judged. It was found that all Raeq values in the samples of ceramic tiles fell within ranges below the threshold standard of 370 Bq/kg [44]. Similarly, the Raeq values for all the samples of the investigated granite tiles were in ranges lower than the criterion limitation of 370 Bq/kg, with the exception of three samples (No. 27 to 29) of GRSS and two samples (No. 33 and 35) from GRN samples. Furthermore, the mean Raeq values varied between 100.96 Bq/kg in the CVE samples and 463 Bq/kg in the GRSS samples, with an overall mean of 174.06 Bq/kg. Accordingly, the granites and ceramic tiles of the different brands herein don't constitute any considerable radiological risks for individuals when used as tiling materials, except for the GRSS samples which may be a cause Evidently, in many of the investigated granite and ceramic samples, the radioisotopes' displayed concentrations were more elevated than the GAVs (Figure 2). For instance, in granites of "Rosa Sardo Sinai" (GRSS) samples, concentrations of uranium, thorium, and potassium exceed their corresponding GAVs by about three times, confirming the previous study on the granite of the Sinai area by Fares [39]. Therefore, it was crucial to assess the likely radiological risks to peoples' health owing to the use of these materials in buildings. Table 4 displays some of the evaluated radiological variables for the granite and ceramic samples under consideration. Through the estimated R eq , I γ , D in , E in , and ELCR (Table 4), the gamma ray hazards posed by the materials under investigation when used as tiling in buildings can be judged. It was found that all Ra eq values in the samples of ceramic tiles fell within ranges below the threshold standard of 370 Bq/kg [44]. Similarly, the Ra eq values for all the samples of the investigated granite tiles were in ranges lower than the criterion limitation of 370 Bq/kg, with the exception of three samples (No. 27 to 29) of GRSS and two samples (No. 33 and 35) from GRN samples. Furthermore, the mean Ra eq values varied between 100.96 Bq/kg in the CVE samples and 463 Bq/kg in the GRSS samples, with an overall mean of 174.06 Bq/kg. Accordingly, the granites and ceramic tiles of the different brands herein don't constitute any considerable radiological risks for individuals when used as tiling materials, except for the GRSS samples which may be a cause for concern due to the mean value of Ra eq going beyond 370 Bq/kg (recommended value) (Figure 5a). for concern due to the mean value of Raeq going beyond 370 Bq/kg (recommended value) (Figure 5a). According to the calculated values of Iγ (Table 4), none of the values in the samples under investigation go beyond the exemption limit of 2. This implies that the yearly effective gamma dose resulting from the investigated materials herein when used as covering According to the calculated values of I γ ( Table 4), none of the values in the samples under investigation go beyond the exemption limit of 2. This implies that the yearly effective gamma dose resulting from the investigated materials herein when used as covering or superficial building materials indoors is less than 0.3 mSv/y (exemption limit indicated by the European Commission [46]). Thus, the granites and ceramic tiles of the brands under investigation are suitable for use without any restrictions. Furthermore, and by way of illustration, Figure 5b displays the estimated mean values of I γ for the granites and ceramic tiles where they do not go beyond their allowable limit, indicating that all of the investigated materials do not raise any cause for concern when used in buildings.

Gamma Radiation Impact Estimation
Considering the estimated D in and E in values for the samples under investigation (Table 4), neither the granites nor the ceramic samples of the various brands examined herein had D in and E in values going beyond their corresponding worldwide average values of 84 nGy/h and 0.41 mSv/y [3] and of 70 nGy/h and 1 mSv/y [46]. Notably, the mean values of D in and E in for the studied granites and ceramic tiles compared with the corresponding global average values (GAVs) are illustrated in Figs. 5c and 5d, where they are below the adopted limits, reflecting their safe use.
The indoor ELCR values based on E in , as well as their mean values in the granites and ceramics under investigation, are shown in Table 4 and plotted in Figure 5e. Evidently, all the ELCR values are within the range of 0.07 to 0.91, with an overall mean of 0.32. Namely, the mean ELCR values in all the brands of tiling materials are less than their corresponding GAV of 1.16 indicated by Sidique et al. [41] and Qureshi et al. [53], as shown in Figure 5e. Thus, in buildings where the materials under investigation are used, over a 66-year lifespan, their residents are at a very insignificant risk of developing cancer resulting from exposure to gamma rays emitted by these materials.

Radon Impact Assessment
The potential radon (Rn-222) risks posed by the studied materials when used as tiles in buildings can be investigated through the estimated I α , RX, C Rn , and E Rn . For the samples of each brand, Table 5 displays ranges and averages of I α , RX, C Rn , and E Rn values, while Figure 6 compares averages of these parameters with their corresponding allowable limits. Table 5 reveals that the I α values oscillate between 0.04 and 0.98, with an overall mean value of 0.23. Furthermore, no mean value of I α for any of the brands' samples under investigation goes beyond the unity, as shown in Figure 6a. Thus, arguably, the materials under consideration come under the range of the indoor radon safe exposure action level for buildings, as indicated by the European Commission [46] and ICRP [49].     [3], as shown in Figure 6b. It is therefore expected that the materials under investigation do not constitute any health risks to dwellers. Based on the RX values, the indoor radon concentration (C Rn ) was assessed from the indirect mathematical model of a typical residence room tiled by the studied ceramics and granites in both poor and normal ventilation cases as per Equation (9). Accordingly, for the room model with normal ventilation, the mean values of C Rn of granites and ceramics from the different brands under investigation fluctuate between 5.67 Bq/m 3 in the CGL samples to 91.73 Bq/m 3 in the GRSS samples, with an overall mean value of 16.13 Bq/m 3 ( Table 5 and Figure 6c). Consequently, for the normal ventilation case, none of the mean values of C Rn in the studied brands of granites and ceramic tiles, as shown in Figure 6c (Table 5 and Figure 6c). Thus, for the poor ventilation case, none of the mean values of C Rn in the studied brands of ceramics and granites, as shown in Figure 6c, exceed the acceptable range (100-300 Bq/m 3 ) declared by the WHO [8], except for GRSS which as a result is not recommended for poorly ventilated buildings.
Regarding the yearly effective dose rate (E Rn ) due to radon concentration (Table 5 and Figure 6d), the mean values span a range from 0.14 mSv/y in the CGL samples to 2.32 mSv/y in the GRSS samples, with an overall mean value of 0.41 mSv/y in the case of normal ventilation. Moreover, all of these values fluctuated below the acceptable range of 3-10 mSv/y documented by ICRP [49], (Figure 6d). On the other hand, for the poor ventilation case, the mean values of E Rn for the granites and ceramics from the different brands under investigation stretch between 0.68 mSv/y in the CGL samples to 10.93 mSv/y in the GRSS samples, with an overall mean value of 1.92 mSv/y. Furthermore, as shown in Figure 6d for poor ventilation, the granite from the brand GRSS is the only one that has a mean value of C Rn going beyond the recommended range of 3-10 mSv/y [49]. Therefore, it is not recommended for poorly ventilated rooms.
The hierarchical cluster analysis (HCA) coupled with the Pearson correlation method was performed to effectively prove the relationship among all considered radiological variables. The dendrogram obtained from the HCA shows the relationship between the radionuclide concentrations and the relevant radiological parameters (Figure 7). Depending on the similarities in existence, all considered variables are gathered into two principal clusters. Cluster I comprised U-238 and Th-232 concentrations as well as all radiological parameters with a highly similar correlation (Figure 7). This reflects that the slight radioactivity level arising in both of the examined granites or ceramic tiles is ascribable to U-238 and Th-232 concentrations. On the other hand, cluster II is only comprised K-40, reflecting the weak relationship of K-40 with the radiological parameters, i.e., despite the high concentration of K-40 in the examined granites and ceramic tiles, K-40 contributes very little to the radioactivity level.

Conclusions
A radiological evaluation for 23 well-known brands of Egyptian commercial granites and ceramic tile samples was performed for hazard and dose estimations. A total of 107 samples representative of the materials under investigation were analyzed using a HPGe detector. The terrestrial radionuclides (U-238 (Ra-226), Th-232, and K-40) concentrations in the investigated samples together with their radiological indices (Raeq, Iγ, Din, Ein, ELCR, Iα, CRn, ERn) were determined. It was found that the concentrations of the aforementioned radioisotopes were higher in most of the granite samples than in the ceramic samples. Furthermore, the concentration values of the terrestrial radionuclides indicated significant differences in the granite and ceramic tile samples collected from the different brands. This is significant in differentiating between the considered brands. K-40 concentration was found to be the biggest contributor to the total concentration for all samples, followed by Th-232 and U-238. Generally, the terrestrial radioisotope concentrations in the materials under investigation are comparable to many of those from the relevant literature and come within the worldwide range. Although the average concentration values for K-40 and Th-232 were higher than their GAVs, the obtained results for the majority of the radiological parameters showed that the studied granites and ceramic tiles are safe to use indoors except "Rosa Sardo Sinai" granite (GRSS). The GRSS samples go beyond the recommended values in terms of their high radium equivalent (Raeq) mean values, and indoor radon concentration (CRn), as well as their associated yearly effective dose rate (ERn) in poorly ventilated buildings, which may be a cause for concern. Therefore, it is not recommended for poorly ventilated buildings. In line with the HCA conducted herein, it reflects the weak relationship of K-40 with all different radiological parameters without exception. In other words, the insignificant risk levels originating from the use of the concerned granites and ceramic tiles are principally due to Th-232 and U-238, with only a weak contribution of K-40.
Our data herein are important for two reasons: firstly, they may raise awareness among the general population of the natural radioactivity of the materials under investigation, and secondly, they are required for developing the standards, rules, and management of tiling materials used in Egypt and in any other country to which such materials are exported.

Conclusions
A radiological evaluation for 23 well-known brands of Egyptian commercial granites and ceramic tile samples was performed for hazard and dose estimations. A total of 107 samples representative of the materials under investigation were analyzed using a HPGe detector. The terrestrial radionuclides (U-238 (Ra-226), Th-232, and K-40) concentrations in the investigated samples together with their radiological indices (Ra eq , I γ , D in , E in , ELCR, I α , C Rn , E Rn ) were determined. It was found that the concentrations of the aforementioned radioisotopes were higher in most of the granite samples than in the ceramic samples. Furthermore, the concentration values of the terrestrial radionuclides indicated significant differences in the granite and ceramic tile samples collected from the different brands. This is significant in differentiating between the considered brands. K-40 concentration was found to be the biggest contributor to the total concentration for all samples, followed by Th-232 and U-238. Generally, the terrestrial radioisotope concentrations in the materials under investigation are comparable to many of those from the relevant literature and come within the worldwide range. Although the average concentration values for K-40 and Th-232 were higher than their GAVs, the obtained results for the majority of the radiological parameters showed that the studied granites and ceramic tiles are safe to use indoors except "Rosa Sardo Sinai" granite (GRSS). The GRSS samples go beyond the recommended values in terms of their high radium equivalent (Ra eq ) mean values, and indoor radon concentration (C Rn ), as well as their associated yearly effective dose rate (E Rn ) in poorly ventilated buildings, which may be a cause for concern. Therefore, it is not recommended for poorly ventilated buildings. In line with the HCA conducted herein, it reflects the weak relationship of K-40 with all different radiological parameters without exception. In other words, the insignificant risk levels originating from the use of the concerned granites and ceramic tiles are principally due to Th-232 and U-238, with only a weak contribution of K-40.
Our data herein are important for two reasons: firstly, they may raise awareness among the general population of the natural radioactivity of the materials under investigation, and secondly, they are required for developing the standards, rules, and management of tiling materials used in Egypt and in any other country to which such materials are exported.
Author Contributions: All the authors contributed to the conception of the study, study design, methodology, data analysis, validation, writing of the original draft, revision of the manuscript, and final publication. All authors have read and agreed to the published version of the manuscript.