Aerosol Characteristics and Their Impact on the Himalayan Energy Budget

The extensive work on the increasing burden of aerosols and resultant climate implications shows a matter of great concern. In this study, we investigate the aerosol optical depth (AOD) variations in the Indian Himalayan Region (IHR) between its plains and alpine regions and the corresponding consequences on the energy balance on the Himalayan glaciers. For this purpose, AOD data from Moderate Resolution Imaging Spectroradiometer (MODIS, MOD-L3), Aerosol Robotic Network (AERONET), India, and Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) were analyzed. Aerosol radiative forcing (ARF) was assessed using the atmospheric radiation transfer model (RTM) integrated into AERONET inversion code based on the Discrete Ordinate Radiative Transfer (DISORT) module. Further, air mass trajectory over the entire IHR was analyzed using a hybrid Single-Particle Lagrangian Integrated Trajectory (HYSPLIT) model. We estimated that between 2001 and 2015, the monthly average ARF at the surface (ARFSFC), top of the atmosphere (ARFTOA), and atmosphere (ARFATM) were −89.6 ± 18.6 Wm−2, −25.2 ± 6.8 Wm−2, and +64.4 ± 16.5 Wm−2, respectively. We observed that during dust aerosol transport days, the ARFSFC and TOA changed by −112.2 and −40.7 Wm−2, respectively, compared with low aerosol loading days, thereby accounting for the decrease in the solar radiation by 207% reaching the surface. This substantial decrease in the solar radiation reaching the Earth’s surface increases the heating rate in the atmosphere by 3.1-fold, thereby acting as an additional forcing factor for accelerated melting of the snow and glacier resources of the IHR.


Introduction
Climate change has been mainly attributed to increased atmospheric greenhouse gases (GHGs) leading towards a warming climate. Apart from GHGs, scientists are also assessing the impact of aerosols in acting as the agents of the warming climate as a result of their established function in affecting the atmospheric energy balance and thus directly affecting global climate model (GCM) predictions. This uncertainty in the GCM projections is partly incorporated by an incomplete understanding of how aerosols affect various climate system components. Aerosols are tiny particles existing in solid, liquid, or gaseous phases (from 0.001 µm to 100 µm), getting circulated between the land surface and stratosphere [1,2]. Biomass burning, mineral dust, volcanic eruptions, and incomplete combustion of fossil fuels are prominent sources of atmospheric aerosols [2,3]. Aerosols of anthropogenic origin influence the microclimatic system through their absorption and scattering of incoming solar radiations [4][5][6].
Aerosols interact with incoming solar radiations, either by the way of scattering or absorption, leading to either a cooling or warming effect on the atmosphere's overall energy budget, respectively [7,8]. It further depends on the land surface and cloud properties. As a result of this interaction, various global atmospheric processes such as regional and local hydrological cycles [9], monsoons [10], and vertical atmospheric heating profiles are affected [11]. On land, due to the warming effect of aerosols, a direct impact in the form of the accelerated melting of glaciers has been reported [11]. Hence, studying atmospheric aerosol and its impact on certain regions of the Earth, considering the indicator-regions of climate change, such as the Himalayas, has been at the forefront of recent studies in climate change science. Studies have concluded with substantial evidence regarding the role of aerosols in inducing tropospheric heating results in the alpine regions of the Himalayas along with their elevated sites [12].
In this work, we made an attempt to understand co-variability between aerosols originating over West Africa and West Asia and appearing heavy loads of aerosols over the Arabian Peninsula and hence its role in generating a dusty aerosol layer along the northwestern part of Indian Himalaya foothills. This dusty layer forms a layer of aerosols along the foothills of the Indian Himalaya and gives rise to the mechanism so-called "elevated heat pump" [13]. This mechanism amplifies the seasonal heating along with the elevated sites of the Indian Himalaya, leading to increased tropospheric warming, particularly from April to June [14][15][16][17], subsequently amplifying and strengthening the monsoon rainfall over northern India between June and July.
Anthropogenic distinctive aerosols have dominated and influential contribution in the microclimatic system through their absorption and scattering properties to solar radiation. This study provides important insight for carrying out studies on the transport of aerosols and their impact over the Himalayan region [7,8]. The scientific research of aerosol characteristics and transportation to the sensitive geographical part of the globe makes us clear about atmospheric warming, glacier retreat, and regional climate change [18]. A holistic assessment of the aerosol optical and transportation can improve the modeling of aerosol effects and variations in the albedo of snow/glaciers over the Trans-Himalayan region [19]. The emission of anthropogenic particles accelerates the changes in the critical physical signature of the Himalayan Mountain ranges, which is nowadays called the aerosol factory of the globe [20]. It has been seen the impacted region over the world due to implications due to climate change in the Himalayan ranges [21][22][23]. This study presents the long-term aerosol radiative variability and optical characteristics like aerosol radiative forcing (ARF). These hilly and fragile mountain ranges show the influence of anthropogenic aerosol and their role in ascendancy solar radiation.

Materials and Methods
The information on aerosol optical characteristics was gathered from three datasets, AERONET L2, MODIS L3, and CALIPSO, in order to meet the study's goals. The AErosol Robotic NETwork (AERONET) initiative is a worldwide chain of ground-based solar Sustainability 2022, 14, 179 3 of 12 photometers used to detect optical aerosol characteristics such as aerosol optical depth (AOD) and aerosol size dispensing (ASD). AERONET collects worldwide estimations of aerosol optical properties in a variety of aerosol systems with high temporal resolution [24]. The AERONET network uses CIMEL sun/sky spectral radiometers to analyze incoming solar radiation extinction at eight wavelengths 0.34, 0.38, 0.44, 0.5, 0.67, 0.87, 0.94, and 1.020 m.
Since 1999, MODIS, onboard NASA's Terra polar-orbiting satellite, has been operational. The Terra satellite allows researchers to examine aerosol from orbit with remarkable precision, almost on a worldwide scale [19]. On a daily basis, MODIS onboard Terra scans the Earth with a swath of 2330 km, allowing it to measure AOD with near-global coverage. Terra runs at 705 km altitude, climbing to the north at 10:30 IST equatorial crossing time. MODIS is a well-calibrated spectroradiometer with 36 spectral channels ranging from 0.41 to 14.4 m. The MODIS method is based on spectral reflectance, which depends on spectral radiance, L λ , the Sun's zenith angle (θ), and irradiance f 0 at wavelength, and is connected by the equation: The λ in the equation has been adjusted in the MODIS AOD products to specifically capture the interaction with the atmospheric aerosols.
The spatial resolutions are 1000 m, 500 m, and 250 m with 29, 5, and 2 spectral bands, respectively [25]. Here, MODIS daily level-3, 005 AOD data (550 nm) at a 1 • latitude/longitude grid were averaged to generate daily MOD08_D3.005 and MYD08_D3.051 data products from Terra and Aqua satellites, respectively. Terra and Aqua operate at an altitude of 705 km, with equatorial passing time at 10:30 Indian Standard Time (IST) ascending towards the north and at 13:30 IST plunging towards the south [26], confirming that the AOD values regained from MODIS are correct within an uncertainty perimeter of ∆τpλ = ±0.05 ± 0.15 τpλ over land, (2) where τ p λ is the ground-based AOD value. The data from Terra and Aqua measured at two different times on a day were combined to obtain the daily mean AOD for that day [27]. The CALIPSO satellite (launched April 2006) used to examine the role of clouds and aerosols in Earth's climate regulation. CALIPSO has a 98º orbit inclination, orbiting at 705 km and disseminating daily worldwide distribution of clouds and aerosols [21]. CALIPSO carries Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP), is an imaging Infrared Radiometer (IIR), and a moderate spatial resolution Wide Field-of-view Camera (WFC) has depolarization corresponding to wavelength 532 nm that are proficient of discriminating amongst ice and water clouds and identifying non-spherical aerosol particles. As a result of this benefit, CALIOP is favored to quantify the vertical structure of dust plumes directly. Here, we used CALIPSO to supplement observations of aerosol acquired by the MODIS.
The ARF calculation algorithm was developed by Kimet et al. as follows [28]: where F is the radiative forcing (W/m 2 ), S incident solar flux at TOA, T + and T − are the upward and downward transmissions, N cloudiness index, τ AOD, α albedo (surface), β radiation scattered as fraction upwards, and ω is the single albedo aerosol scattering. Using ARONET retrieved aerosol optical depth, fundamental part and imaginary part natural refractive index (or single scattering albedo) at 500 nm, and volume size distribution, radiative transfer model calculates solar direct and diffuse flux. The estimated solar fluxes are related to variations in solar fluxes. This process changes the water vapor ratio of the refractive index. The transfer radiative model calculates aerosol radiative forcing at the top of the atmosphere and the surface using an adjusted sky radiometer measured aerosol optical properties. The Santa Barbara DISORT Atmospheric Radiative Transfer (SBDART) model is used to recreate the solar irradiance over the study area at the surface, within the atmosphere, and over top of the atmosphere (TOA). The SBDART is used to solve radiative transfer algorithms to estimate the radiative effects of atmospheric boundary layers [29]. The essential info parameters utilized in the SBDART for forcing estimations are SSA, asymmetry parameter (AP), and AOD. Aerosol Radiative Forcing (ARF) depicts the influence of aerosols on the absorption and scattering of solar radiations. The positive values of ARF indicate the warming, and negative values indicate the cooling.
In this study, these parameters were obtained from the OPAC database [30]. Here, we make use of OPAC (Optical Properties of Aerosol and Clouds version) using Ångström exponent associated with the matching absorption coefficient. Further, using the Discrete Ordinate Radiative Transfer module, the clear-sky SWARF calculations in the shortwave region, i.e., 0.25-4.0 µm, are made by using the radiative transfer model (RTM) [29]. Spectral AOD and SSA used as input in RTM were estimated from the OPAC database at wavelength of 0.25-4.0 µm. Figure 1 is drawn to illustrate seasonal changes in aerosol characteristics, i.e., aerosol optical depth (AOD) at 0.55 µm wavelength. From the figure, it depicts that the distribution of aerosols is not uniform. The continental aerosol plumes disperse over a wider area of oceanic regions. MODIS observations recognize that the Sahara dust plume is the globally distributed aerosol plume and is extended to several thousand kilometers over the Atlantic Ocean. MODIS observations also identified a few more aerosol hotspots, such as the Taklamakan region, the eastern part of China, the tropical part of Africa, the Arabian Sea, and Indo-Gangetic Plains (IGP). The AOD over these aerosol hotspots regions in most of the months of the year remains more significant than 0.6. Sustainability 2022, 13, x FOR PEER REVIEW 4 of 12 measured aerosol optical properties. The Santa Barbara DISORT Atmospheric Radiative Transfer (SBDART) model is used to recreate the solar irradiance over the study area at the surface, within the atmosphere, and over top of the atmosphere (TOA). The SBDART is used to solve radiative transfer algorithms to estimate the radiative effects of atmospheric boundary layers [29]. The essential info parameters utilized in the SBDART for forcing estimations are SSA, asymmetry parameter (AP), and AOD. Aerosol Radiative Forcing (ARF) depicts the influence of aerosols on the absorption and scattering of solar radiations. The positive values of ARF indicate the warming, and negative values indicate the cooling. In this study, these parameters were obtained from the OPAC database [30]. Here, we make use of OPAC (Optical Properties of Aerosol and Clouds version) using Ångström exponent associated with the matching absorption coefficient. Further, using the Discrete Ordinate Radiative Transfer module, the clear-sky SWARF calculations in the shortwave region, i.e., 0.25-4.0 μm, are made by using the radiative transfer model (RTM) [29]. Spectral AOD and SSA used as input in RTM were estimated from the OPAC database at wavelength of 0.25-4.0 μm. Figure 1 is drawn to illustrate seasonal changes in aerosol characteristics, i.e., aerosol optical depth (AOD) at 0.55 μm wavelength. From the figure, it depicts that the distribution of aerosols is not uniform. The continental aerosol plumes disperse over a wider area of oceanic regions. MODIS observations recognize that the Sahara dust plume is the globally distributed aerosol plume and is extended to several thousand kilometers over the Atlantic Ocean. MODIS observations also identified a few more aerosol hotspots, such as the Taklamakan region, the eastern part of China, the tropical part of Africa, the Arabian Sea, and Indo-Gangetic Plains (IGP). The AOD over these aerosol hotspots regions in most of the months of the year remains more significant than 0.6. Moreover, atmospheric changes due to aerosols are operative in these aerosol hotspots areas [31]. The AOD characteristics for the period of March-May were found Moreover, atmospheric changes due to aerosols are operative in these aerosol hotspots areas [31]. The AOD characteristics for the period of March-May were found different from that of September-November. The seasonal biomass burning, particularly during September-November, is eye-catching over the Amazon basin in South America and South Africa [32,33]. This feature reflects the seasonal dependent behavior of AOD characteristics. The seasonal dependent behavior of AOD characteristics can also be seen over the Mediterranean and the Arabian Sea, as reported by Sheel et al. [25].

A View of Regional Aerosol Characteristics: Indian Region
The maps of regional AOD characteristics over the Indian region depict that the aerosol distribution pattern is more or less similar in all years ( Figure 2). These maps are drawn using an integrated approach of MODIS sensors, i.e., Dark Target and Deep Blue, which have separate land and ocean algorithms. There can be noticed with a decreasing pattern in aerosol distribution from 2003 to 2007, whereas there observed no significant change over the Arabian Sea with shifts to higher aerosol loadings. The signatures of aerosol burden over the Arabian Sea before and after 2007 are distinguishable. The satellite maps suggest heavy dust storms after 2007 [34].
Sustainability 2022, 13, x FOR PEER REVIEW 5 of 12 different from that of September-November. The seasonal biomass burning, particularly during September-November, is eye-catching over the Amazon basin in South America and South Africa [32,33]. This feature reflects the seasonal dependent behavior of AOD characteristics. The seasonal dependent behavior of AOD characteristics can also be seen over the Mediterranean and the Arabian Sea, as reported by Sheel et al. [25].

A View of Regional Aerosol Characteristics: Indian Region
The maps of regional AOD characteristics over the Indian region depict that the aerosol distribution pattern is more or less similar in all years ( Figure 2). These maps are drawn using an integrated approach of MODIS sensors, i.e., Dark Target and Deep Blue, which have separate land and ocean algorithms. There can be noticed with a decreasing pattern in aerosol distribution from 2003 to 2007, whereas there observed no significant change over the Arabian Sea with shifts to higher aerosol loadings. The signatures of aerosol burden over the Arabian Sea before and after 2007 are distinguishable. The satellite maps suggest heavy dust storms after 2007 [34]. The western part of India, particularly Rajasthan, was observed with extensive aerosol loading followed by Gujarat. A slight decrease in annual mean AOD can be noticed in the following years, which could be related to enhanced forest cover and rainfall [35]. A moderate AOD can be seen over Madhya Pradesh and western Maharashtra. Eastern India comprises the IGP region and observes a heavy aerosol burden. The sizeable annual aerosol loading can be ascribed to its topography (i.e., northern plain and the elevated Himalayas), patterns of wind, and higher emissions from anthropogenic sources [36]. The The western part of India, particularly Rajasthan, was observed with extensive aerosol loading followed by Gujarat. A slight decrease in annual mean AOD can be noticed in the following years, which could be related to enhanced forest cover and rainfall [35]. A moderate AOD can be seen over Madhya Pradesh and western Maharashtra. Eastern India comprises the IGP region and observes a heavy aerosol burden. The sizeable annual aerosol loading can be ascribed to its topography (i.e., northern plain and the elevated Himalayas), patterns of wind, and higher emissions from anthropogenic sources [36]. The amount of aerosol was noted over West Bengal, followed by Bihar and Jharkhand. The eastern states observe moderate to low aerosol loading. Satellite observations capture an increasing pattern from west to east, especially IGP. Southern India experiences a relatively Sustainability 2022, 14, 179 6 of 12 low aerosol burden. However, moderate to high aerosol loadings in surrounding oceanic regions can be observed. The Southern part of India (Kerala, Karnataka, and Tamil Nadu) experiences the lowest aerosol burden, particularly in the winter season, whereas the maximum is in the monsoon. Figures 1 and 2 confirm that IGP is an aerosol hotspot area in the Himalayan foothills. The aerosol accumulated along the elevated sites of the Himalayas is mainly associated with desert dust [37], which is primarily transported from western regions [38]. These dust plumes are further transported towards elevated Indian Himalaya, imposing a severe threat to the Himalayan glaciers. The collective approach of HYSPLIT back-trajectory analysis, MODIS, and CALIPSO observations is a vital tool to identify aerosol sources employing transport from the distant source origin. This collective approach was previously used in numerous studies [39,40].

Observational Evidence of Aerosol Transport towards the Elevated Sites of the Himalaya
Globally, the incidences of events of dust storms are the most prevalent atmospheric phenomenon from March to June. The Sahara Desert, the Thar Desert of India, and the Arabian region are the primary origins of aerosols of desert dust. Desert dust originates over these regions and then is widely distributed by means of atmospheric transport. The observational evidence of atmospheric dust transport (dust plumes) is revealed from the satellite imaginaries (see Figure 3).  Figures 1 and 2 confirm that IGP is an aerosol hotspot area in the Himalayan foothills. The aerosol accumulated along the elevated sites of the Himalayas is mainly associated with desert dust [37], which is primarily transported from western regions [38]. These dust plumes are further transported towards elevated Indian Himalaya, imposing a severe threat to the Himalayan glaciers. The collective approach of HYSPLIT back-trajectory analysis, MODIS, and CALIPSO observations is a vital tool to identify aerosol sources employing transport from the distant source origin. This collective approach was previously used in numerous studies [39,40].

Observational Evidence of Aerosol Transport towards the Elevated Sites of the Himalaya
Globally, the incidences of events of dust storms are the most prevalent atmospheric phenomenon from March to June. The Sahara Desert, the Thar Desert of India, and the Arabian region are the primary origins of aerosols of desert dust. Desert dust originates over these regions and then is widely distributed by means of atmospheric transport. The observational evidence of atmospheric dust transport (dust plumes) is revealed from the satellite imaginaries (see Figure 3). On 10 June 2010, the MODIS on the Terra satellite recorded a massive dust plume that swept across the Sahara Desert (Figure 3a). The plume spreads from Mauritania through Mali and into Algeria, appears only slightly brighter than the earth-toned terrain below. The dust plume develops unique wave patterns over Algeria, but it is thinner than it was over Mali. The dust storm's source locations aren't visible in this view, but vast sand seas engulf almost all of Mauritania, crossing the Mali-Algerian border. The original dust plumes are thought to have originated in the southwest and blown northeast, churning up further dust and dirt along the route. On 9 June 2010, thick clouds of desert dust blew across Pakistan (left) and India (right) in the base of the Himalayan Mountains (Figure 3b). The MODIS-Terra satellite obtained this image of the incident. On the snowcapped peaks of the Himalayas at the top right and the Indo-Gangetic Plain, the storm looks to be putting down a blanket of dust. We infer from satellite image analysis that On 10 June 2010, the MODIS on the Terra satellite recorded a massive dust plume that swept across the Sahara Desert (Figure 3a). The plume spreads from Mauritania through Mali and into Algeria, appears only slightly brighter than the earth-toned terrain below. The dust plume develops unique wave patterns over Algeria, but it is thinner than it was over Mali. The dust storm's source locations aren't visible in this view, but vast sand seas engulf almost all of Mauritania, crossing the Mali-Algerian border. The original dust plumes are thought to have originated in the southwest and blown northeast, churning up further dust and dirt along the route. On 9 June 2010, thick clouds of desert dust blew across Pakistan (left) and India (right) in the base of the Himalayan Mountains (Figure 3b). The MODIS-Terra satellite obtained this image of the incident. On the snow-capped peaks of the Himalayas at the top right and the Indo-Gangetic Plain, the storm looks to be putting down a blanket of dust. We infer from satellite image analysis that many dust aerosols start over the Sahara, India's Thar Desert, and the Arabian area and then travel to the northern section of the country, impacting regional climate.
To investigate the influence of atmospheric dust transport in modulating the physical properties of aerosols, we took the example of a typical month, i.e., May 2016, and the day of low aerosol loading (7 May 2016) and extensive aerosol loading (27 May 2016) are analyzed. The aerosol volume size distribution (DV/dlnR) depicts aerosols' bi-modal structure (Figure 4). AERONET station installed at IIT Kanpur is one of the represented sites in IGP. The aerosol volume distribution is estimated from the spectral Sun and sky radiance data using a well-explained technique by Dubovik and King (2002) [41]. We found that during dust aerosol loading day, the volume concentration of aerosols in the size range of 1.3-8.0 µm has increased significantly, implying the domination of coarsemode particles. Dubovik et al. (2002) observed this type of volume size distribution for desert aerosols. For size particles r < 1.0 µm, there is no significant variation, even during dust loading day, which results in atmospheric transport carrying desert dust (a source of coarse-mode aerosols). Similar results by Dey et al. (2004) report that during dust episode days, the concentration at coarse-mode rises three times, with little change in volume of fine particles [42]. The aerosol volume size exhibits two prominent characteristics: fine particles r < 1.0 µm and coarse particles r > 1.0 µm. Sustainability 2022, 13, x FOR PEER REVIEW 7 of 12 many dust aerosols start over the Sahara, India's Thar Desert, and the Arabian area and then travel to the northern section of the country, impacting regional climate.
To investigate the influence of atmospheric dust transport in modulating the physical properties of aerosols, we took the example of a typical month, i.e., May 2016, and the day of low aerosol loading (7 May 2016) and extensive aerosol loading (27 May 2016) are analyzed. The aerosol volume size distribution (DV/dlnR) depicts aerosols' bi-modal structure ( Figure 4). AERONET station installed at IIT Kanpur is one of the represented sites in IGP. The aerosol volume distribution is estimated from the spectral Sun and sky radiance data using a well-explained technique by Dubovik and King (2002) [41]. We found that during dust aerosol loading day, the volume concentration of aerosols in the size range of 1.3-8.0 μm has increased significantly, implying the domination of coarse-mode particles. Dubovik et al. (2002) observed this type of volume size distribution for desert aerosols. For size particles r < 1.0 μm, there is no significant variation, even during dust loading day, which results in atmospheric transport carrying desert dust (a source of coarse-mode aerosols). Similar results by Dey et al. (2004) report that during dust episode days, the concentration at coarse-mode rises three times, with little change in volume of fine particles [42]. The aerosol volume size exhibits two prominent characteristics: fine particles r < 1.0 μm and coarse particles r > 1.0 μm.

Discussion
Here, we investigate the influence of atmospheric dust transport on aerosol radiative forcing (ARF) over Kanpur. The significant aerosol loading day (27 May 2016) and low aerosol loading day (7 May 2016) are taken to observe the radiative effect of aerosols. The nearest CALIPSO pass transecting air parcels was available on 27 May 2016, at nighttime. The CALIPSO swath while passing from over India is shown in Figure 5. The air parcel (drawn at 5000 m above ground level) reached India on 27 May 2016 and was initiated from the Sahara. It after that passed via Saudi Arabia, Iran, and Afghanistan and created a vertical layer of dust aerosol over northern India.
Moreover, the air parcel travels the distance above the boundary layer. The boundary layer played an essential role in carrying the aerosol over a long distance. These features are explained by HYSPLIT back-trajectories connected with CALIPSO satellite

Discussion
Here, we investigate the influence of atmospheric dust transport on aerosol radiative forcing (ARF) over Kanpur. The significant aerosol loading day (27 May 2016) and low aerosol loading day (7 May 2016) are taken to observe the radiative effect of aerosols. The nearest CALIPSO pass transecting air parcels was available on 27 May 2016, at nighttime. The CALIPSO swath while passing from over India is shown in Figure 5. The air parcel (drawn at 5000 m above ground level) reached India on 27 May 2016 and was initiated from the Sahara. It after that passed via Saudi Arabia, Iran, and Afghanistan and created a vertical layer of dust aerosol over northern India.
Moreover, the air parcel travels the distance above the boundary layer. The boundary layer played an essential role in carrying the aerosol over a long distance. These features are explained by HYSPLIT back-trajectories connected with CALIPSO satellite observations in the events of dust aerosol loading day, i.e., 27 May 2016 ( Figure 5). The air parcels suggest the western flow of air-born particles towards India.
observations in the events of dust aerosol loading day, i.e., 27 May 2016 ( Figure 5). The air parcels suggest the western flow of air-born particles towards India.  Figure 5. The depolarization ratio is applied to distinguish different dust aerosols and is defined as the fraction of the perpendicular and the parallel components of the weakened backscatter signal. CALIPSO depolarization ratio image suggests a higher value > 0.4 near the surface (Figure 6a,b). Higher depolarization suggests a significant contribution of desert dust particles [38]. This feature is derived from CALIOP backscatter measurements, which realize that advected desert dust accompanies the near-surface aerosols. Figure 6c depicts a vertically extended tropospheric aerosol layer of ~7 km over northern India. The vertical profile of CALIPSOderived image analysis has confirmed the dispersion of dust from the western deserts towards the north part of India (see Figure 6d).
In summary, on 27 May 2016, the western flow of air-born particles has amplified the likelihood of aerosol dust transport near Kanpur. On May 27, 2016, the AOD at 500 nm value was noted to be 313% higher when compared to low AOD day, i.e., 7 May 2016. About 90% decrease in α (440-870 nm) was estimated on 27 May 2016, as compared to 7 May 2016, which suggests a notable loading of dust. Figure 7 shows the status of ARF at TOA, SFC, and ATM. The influence of extensive aerosol loading can be revealed in Figure  7. It is found that atmospheric desert dust transport has a greater impact, with a notable decrease in surface-reaching solar radiation. During significant aerosol loading day, i.e., May 27, 2016, the desert dust transport causes a substantial decrease in the surface-reaching shortwave solar radiation by 166.4 Wm −2 . During this day, the atmospheric aerosol radiative forcing increased by 106. This results in a considerable reduction in the surface-reaching solar radiation by 207%. Such a considerable reduction in the surface-reaching solar radiation enhances the atmospheric heating rate by 3.1-fold. A study to investigate the aerosol impact on surface incoming solar radiations was also performed by Prasad et al. (2007) from AERONET site Kanpur and showed that during dusty days, the average ARF at the SFC and TOA change by −23 and −11 Wm −2 , respectively [43]. Nevertheless, the magnitude of reduction in present work is much higher than earlier work [43,44]. In summary, we conclude that aerosol  Figure 5. The depolarization ratio is applied to distinguish different dust aerosols and is defined as the fraction of the perpendicular and the parallel components of the weakened backscatter signal. CALIPSO depolarization ratio image suggests a higher value > 0.4 near the surface (Figure 6a,b). Higher depolarization suggests a significant contribution of desert dust particles [38]. This feature is derived from CALIOP backscatter measurements, which realize that advected desert dust accompanies the near-surface aerosols. Figure 6c depicts a vertically extended tropospheric aerosol layer of~7 km over northern India. The vertical profile of CALIPSOderived image analysis has confirmed the dispersion of dust from the western deserts towards the north part of India (see Figure 6d).
In summary, on 27 May 2016, the western flow of air-born particles has amplified the likelihood of aerosol dust transport near Kanpur. On May 27, 2016, the AOD at 500 nm value was noted to be 313% higher when compared to low AOD day, i.e., 7 May 2016. About 90% decrease in α (440-870 nm) was estimated on 27 May 2016, as compared to 7 May 2016, which suggests a notable loading of dust. Figure 7 shows the status of ARF at TOA, SFC, and ATM. The influence of extensive aerosol loading can be revealed in Figure 7. It is found that atmospheric desert dust transport has a greater impact, with a notable decrease in surface-reaching solar radiation. During significant aerosol loading day, i.e., May 27, 2016, the desert dust transport causes a substantial decrease in the surface-reaching shortwave solar radiation by 166.4 Wm −2 . During this day, the atmospheric aerosol radiative forcing increased by 106.3 Wm −2 and translated into 2.98 K day −1 of atmospheric heating rate. The monthly average (mean ± σ) value of ARF during May 2016 stood as −24.4 ± 14.8 Wm −2 , −109.5 ± 35.4 Wm −2 , and 83.1 ± 38.4 Wm −2 at TOA, SFC, and ATM, respectively. Our work assessed that during DATD (dust aerosol transport day), the ARF at SFC and TOA vary by −112.2 and −40.7 Wm −2 , respectively, against the low aerosol loading days.
This results in a considerable reduction in the surface-reaching solar radiation by 207%. Such a considerable reduction in the surface-reaching solar radiation enhances the atmospheric heating rate by 3.1-fold. A study to investigate the aerosol impact on surface incoming solar radiations was also performed by Prasad et al. (2007) from AERONET site Kanpur and showed that during dusty days, the average ARF at the SFC and TOA change by −23 and −11 Wm −2 , respectively [43]. Nevertheless, the magnitude of reduction in present work is much higher than earlier work [43,44]. In summary, we conclude that aerosol has a profound impact in modulating aerosols' physical and radiative properties, which leads to climate forcing. has a profound impact in modulating aerosols' physical and radiative properties, which leads to climate forcing.

Conclusions
In 1993, National Aeronautics Space Administration (NASA) took the initiative to measure aerosols and launch a worldwide program called the AERONET program. Now with more than 500 AERONET stations, it is the world's most extensive program. The AERONET station at IIT Kanpur became operational on 22 January 2001. In India, it has been one of the ground stations monitoring aerosol for a long time. In recent years, numerous initiatives were also taken by the world's different agencies/organizations to monitor aerosol from space. Over India, satellite observations capture a decreasing pattern from 2003-2007, whereas there observed no significant change over the Arabian Sea. The has a profound impact in modulating aerosols' physical and radiative properties, which leads to climate forcing.

Conclusions
In 1993, National Aeronautics Space Administration (NASA) took the initiative to measure aerosols and launch a worldwide program called the AERONET program. Now with more than 500 AERONET stations, it is the world's most extensive program. The AERONET station at IIT Kanpur became operational on 22 January 2001. In India, it has been one of the ground stations monitoring aerosol for a long time. In recent years, numerous initiatives were also taken by the world's different agencies/organizations to monitor aerosol from space. Over India, satellite observations capture a decreasing pattern from 2003-2007, whereas there observed no significant change over the Arabian Sea. The

Conclusions
In 1993, National Aeronautics Space Administration (NASA) took the initiative to measure aerosols and launch a worldwide program called the AERONET program. Now with more than 500 AERONET stations, it is the world's most extensive program. The AERONET station at IIT Kanpur became operational on 22 January 2001. In India, it has been one of the ground stations monitoring aerosol for a long time. In recent years, numerous initiatives were also taken by the world's different agencies/organizations to monitor aerosol from space. Over India, satellite observations capture a decreasing pattern from 2003-2007, whereas there observed no significant change over the Arabian Sea. The variation in AOD was observed to be wavelength-dependent, showing seasonal dependence characteristics. The HYSPLIT trajectory analysis showed that the air masses that originate or pass through over western regions profoundly impact the Himalayan radiation budget. The ARF was analyzed to see the impact of aerosols on the Himalayan radiation budget. The monthly average ARF at the surface, within and, top-of-the atmosphere, was estimated to be -89.6 ± 18.6 Wm −2 , -25.2 ± 6.8 Wm −2 , and +64.4 ± 16.5 Wm −2 , respectively. The above work examined that during dust aerosol transport day, the ARF at the surface and top-of-the atmosphere change by −112.2 and −40.7 Wm −2 , respectively, when results relate to declined aerosol loading day. In summary, we conclude that aerosol has a profound impact in modulating the radiation transfer, leading to climate forcing.