Anaerobic Degradability of Commercially Available Bio-Based and Oxo-Degradable Packaging Materials in the Context of their End of Life in the Waste Management Strategy

There are discrepancies concerning the time frame for biodegradation of different commercially available foils labeled as biodegradable; thus, it is essential to provide information about their biodegradability in the context of their end of life in waste management. Therefore, one-year mesophilic (37 °C) anaerobic degradation tests of two bio-based foils (based on starch (FS), polylactic acid (FPLA)) and oxo-degradable material (FOXO) were conducted in an OxiTop system. Biodegradation was investigated by measuring biogas production (BP) and analyzing structural changes with differential scanning calorimetry, polarizing and digital microscopic analyses, and Fourier transform infrared spectroscopy. After 1 year, FOXO had not degraded; thus, there were no visible changes on its surface and no BP. The bio-based materials produced small amounts of biogas (25.2, FPLA, and 30.4 L/kg VS, FS), constituting 2.1–2.5% of theoretical methane potential. The foil pieces were still visible and only starting to show damage; some pores had appeared in their structure. The structure of FPLA became more heterogeneous due to water diffusing into the structure. In contrast, the structure of FS became more homogenous although individual cracks and fissures appeared. The color of FS had changed, indicating that it was beginning to biodegrade. The fact that FS and FPLA showed only minor structural damage after a one-year mesophilic degradation indicates that, in these conditions, these materials would persist for an unknown but long amount of time.


Introduction
The worldwide use of bioplastics (bio-based products) has been increasing, and it is expected that the share of bio-based products on the plastics market will increase by 40% by 2030 [1]. These products are most often used as food packaging, frozen food containers, milk and juice cartons, disposable tableware, or for agriculture purposes [2]. Bio-based products are wholly or partly of biological origin, e.g., based on lignin, cellulose, or starch. These products contain from 20% up to 100% renewable raw materials and can be both biodegradable and non-biodegradable [3]. However, the most desirable are biodegradable or compostable products, which degrade anaerobically or aerobically in the presence of microorganisms. Among biodegradable bio-based products, starch-based materials and polylactic acid (PLA) are the most common, constituting 44% and 24% of the global production capacity for biodegradable polymers, respectively. Other biopolymers produced at an industrial scale are poly(butylene succinate) (PBS) and poly(butyleneadipateterephthalate) (PBAT), which constitute 23% of the global production capacity, and polyhydroxyalkanoates (PHA), which constitute 6% [4]. PLA can be synthesized from renewable biomass ISO 14853:2016, used to determine the anaerobic biodegradability of plastic materials in an aqueous medium, calls for exposure of the test polymers to sludge at 35 • C ± 2 • C for a period of up to 90 days [28]. This time is longer than the conventional sludge retention time (25 to 30 days) in anaerobic digesters. Massardier-Negotte et al. [29] used ISO 14853 for anaerobic tests and found that, in these conditions, biopolymers (PLA, polycaprolactone, starch/polycaprolactone, and PBAT) degraded slightly or did not degrade.
To determine the degree and rate of anaerobic mesophilic biodegradation of plastic materials, ASTM D5526 may be also used [30]. In this test, the inoculum should be derived from anaerobic digesters operating only with pretreated household waste. Biodegradation should be carried out under dry (>30% total solids (TS)) and static non-mixed conditions. Another test of polymer biodegradability is provided by EN 13432, which defines the requirements for determining the compostability and anaerobic treatability of plastic packaging materials [31]. Zhang et al. [32] carried out mesophilic anaerobic degradation of nine different bioplastics (based on cellulose, starch, and PLA) according to EN13432. They concluded that only four bioplastics showed substantial biodegradability, but less than 20% of their carbon was converted into methane.
In summary, many products on the market are labeled as biodegradable. However, even though various products can be based on the same main component, e.g., starch or PLA, its content in the products can differ. Moreover, manufacturers use various types of additives in different proportions to improve the functional properties of a material. Unfortunately, however, the manufacturers do not provide detailed information on the composition of their products. Most likely, the types and proportions of the additives are the main factors determining the biodegradability of bioplastics and the time frame for their biodegradation. Thus, reports on the degree of biodegradation of different bioplastics during anaerobic treatment differ substantially [33][34][35][36]. Moreover, for wastemanagement and end-of-life considerations, it is essential to provide information on as many as possible of the commercially available materials that are considered biodegradable. Therefore, the aim of this study was to investigate the degradation of selected bio-based and oxo-degradable products (waste disposal bags) during a long-term (1-year) anaerobic mesophilic biodegradation test. Three different commercially available foil materials were studied by observing changes in their structure with the use of polarizing and digital microscopic analyses, Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC).

Bio-Based Materials and Oxo-Degradable Material
In the present study, three different commercially available foils were subjected to anaerobic mesophilic (37 • C) degradation. Two of them were bio-based products: BioBag waste bags made from Mater-Bi ® material based on starch (F S ) and bags made from polylactic acid (F PLA ). The third foil was an oxo-degradable product (F OXO ), consisting of conventional polyethylene containing the pro-oxidant additive d2w. Each of the investigated foils was cut to a particle size of 10 × 10 mm. The characteristics of the materials are presented in Table 1. To improve their functional properties, these products, which were purchased on the commercial public market, may have contained other additives. Unfortunately, however, the manufacturer did not provide details of their composition.

Measurement of Biogas Production
An anaerobic biodegradation test with measurement of biogas production from biobased and oxo-degradable foils was performed under mesophilic conditions (37 ± 0.5 • C) with the use of a standard test of gas potential (ISO 14853:2016) with modifications [28]. The measurement lasted 1 year and was carried out in triplicate for each foil with the use of the OxiTop ® Control system (WTW Wissenschaftlich-Technische Werkstätten GmbH, Germany), which consists of measuring vessels (bioreactors) with a capacity of 630 mL and measuring heads with built-in pressure sensors. Pressure values obtained from respirometric measurements allowed determination of the volume of biogas produced. To ensure anaerobic conditions, the space above the sample was flushed with nitrogen gas before measurements.
To determine the biogas production from foil, the inoculum (approximately 100 mL) and the foil were introduced into the OxiTop bioreactors. The inoculum was fermented sludge from a closed mesophilic digester chamber from a municipal wastewater treatment plant employing the activated sludge method (north-eastern Poland). The planned initial organic load (OL) was 4 kg VS/m 3 , indicating that the doses of foils were 0.4 g. Additionally, biogas production by the inoculum alone was determined. The biogas production of the foils themselves was determined by taking the difference between the amount of biogas generated in the bioreactors with inoculum and foil and the amount of biogas generated in the bioreactors with only inoculum.
Additional glass bottles, with volume identical to those of the bioreactors, were prepared to enable sampling of foil pieces from these bottles. These bottles were prepared in the same manner as the OxiTop vessels, which were used only for measuring biogas production. All the bioreactors and bottles were placed in a thermostatic incubator. Every month during anaerobic biodegradation tests, pieces of F S , F PLA , and F OXO were removed from the inoculum for the microscopic, differential scanning calorimetry (DSC), and FTIR analyses. However, the results of these analyses did not show any changes in comparison with the raw materials during the first year. Changes finally appeared after 1 year, and only these results are shown below.

Microscopic and FTIR Analysis
The changes on the surface of the bio-based and oxo-degradable materials were analyzed using a Nikon eclipse50i polarizing microscope at a magnification of 100× and digital microscope (Keyence VHX-7000, Osaka, Japan) at a magnification of 1000×. Additionally, the digital microscope allows to determine 3D geometric structure (topography) at the microscale without contact with the investigated foil sample.
The FTIR spectra were collected using a PerkinElmer Spectrum Two (with diamond ATR) brand device within the wavenumber range of 4000-400 cm −1 and resolution of 4 cm −1 at room temperature and repeated in triplicate for each foil material. Smoothing functions were not employed.

Differential Scanning Calorimetry Analysis
In the raw foil materials and after 1 year of the degradation, thermal properties of biobased and oxo-degradable foils were investigated with a differential scanning calorimetry analysis (DSC) on DSC Phoenix 204 F1 differential scanning calorimeter utilizing hit flow method (NETZSCH, Selb, Germany). The measured parameter is free heat flow. Small amounts (ca. 5 mg) of dry samples of each of the foils were placed into aluminum crucibles, sealed, and heated at between 30 • C and 200 • C at a heating rate of 5 • C/min. An empty aluminum crucible was used as reference. The analysis based on the measurement of energy required to establish a zero-temperature difference between the analyzed sample and a reference sample. The thermal characteristics such as the glass transition temperature (Tg), cold crystallization temperature (Tcc), cold crystallization enthalpy (∆Hcc), melting temperature (Tm), and melting enthalpy (∆Hm) were determined from DSC curves.

Analytical Methods
Volatile solids (VS) as loss on ignition and the contents of COD and TN (as total Kjeldahl nitrogen) in foil materials (if possible) were determined according to APHA [37]. Elemental composition of the materials was determined with the use of Flash 2000 Organic Elemental Analyzer (Thermo Scientific, Milan, Italy).

Anaerobic Biodegradation Test of Selected Bio-Based and Oxo-Degradable Materials in OxiTop System
Anaerobic biodegradation of pieces of foils of F S , F PLA , and F OXO were carried out under mesophilic conditions at 35 • C. The OxiTop system allowed measurement of the volume of biogas (in mL) produced during the anaerobic test. During the analyses of biogas volume (BV) from investigated material, two BV profiles were considered. The inoculum alone (I) represents the first profile. The inoculum with the material (F S + I, F PLA + I) represents the second profile. The profile of the biogas volume for the material alone is possible to be obtained by subtracting the values of the first profile from the second. As shown in Figure 1, the profiles of biogas volume corresponding to the inoculum alone and to both the inoculum and the foil material were very close to each other. This means that the biogas volume corresponding to the foil material alone would be very low. This was confirmed by the value of BP in liters per kg of organic matter (L/kg VS), that is, the most commonly used units for BP during anaerobic measurements in this kind of system, as the VS content of the foil materials was considered to reflect the organic matter content. The profiles corresponding to the inoculum alone and to both the inoculum and the foil material of F OXO showed no differences indicating lack of degradation; thus, no BV and BP profiles are provided.
The profiles of the biogas volume for the bio-based foil materials of FPLA and FS showed the initial long lag phases. With FS, the lag phase was even longer, lasting 70 days, whereas with FPLA, it lasted 60 days. After the lag phase, BP started to increase very slowly until 160-180 day of the measurements, and then, the biogas volumes remained the same until the end of an almost 400-day anaerobic test. The final biogas production for FPLA and FS was similar: 25.2 and 30.4 L/kg VS, respectively.
Based on the elementary composition of the foil materials, the theoretical amounts of methane (theoretical methane potential, TMP), assuming complete conversion of organics into biogas, were calculated using the Buswell equation [38]: The theoretical molar compositions of the methane that could be obtained from one mole of the tested foil materials were as follows:  Based on the elementary composition of the foil materials, the theoretical amounts of methane (theoretical methane potential, TMP), assuming complete conversion of organics into biogas, were calculated using the Buswell equation [38]: The theoretical molar compositions of the methane that could be obtained from one mole of the tested foil materials were as follows: To calculate the mass of methane and carbon dioxide, molar masses were considered. Then, to determine the theoretical volumes of gases, their densities were considered as 0.717 g/L and 1.978 g/L, respectively (at 0 °C, 101 kPa). The values of TMP of FS and FPLA (based on the elemental composition) are 577 and 610 L/kg VS, and they are also shown in Figure 1 for comparison with the obtained BP. Assuming that methane content in biogas from FS and FPLA would be ca. 50% [38], the values of methane production (MP) would be two times lower than biogas production, ca. 12 and ca. 15 L/kg VS, respectively.
Most of the studies assumed that the value of TMP is the maximal value of methane that could be obtained. The ratios of MP/TMP for FS and FPLA are 0.021 and 0.025. Thus, FS and FPLA produced methane in amounts constituting only 2.1% and 2.5%, respectively, of the TMP values.
There are discrepancies concerning the time frame for the biodegradation of different biopolymers, and most researchers have not provided information on biogas yield. Bátori et al. [36] found that some biopolymers, such as starch, cellulose, pectin, and poly(hydroxyalkanoate), can be degraded at hydraulic retention times commonly used in biogas plants. Shin et al. [39] reported that 89% of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB/HV; 92/8, w/w) could be degraded within 20 days under anaerobic mesophilic con- To calculate the mass of methane and carbon dioxide, molar masses were considered. Then, to determine the theoretical volumes of gases, their densities were considered as 0.717 g/L and 1.978 g/L, respectively (at 0 • C, 101 kPa). The values of TMP of F S and F PLA (based on the elemental composition) are 577 and 610 L/kg VS, and they are also shown in Figure 1 for comparison with the obtained BP. Assuming that methane content in biogas from F S and F PLA would be ca. 50% [38], the values of methane production (MP) would be two times lower than biogas production, ca. 12 and ca. 15 L/kg VS, respectively.
Most of the studies assumed that the value of TMP is the maximal value of methane that could be obtained. The ratios of MP/TMP for F S and F PLA are 0.021 and 0.025. Thus, F S and F PLA produced methane in amounts constituting only 2.1% and 2.5%, respectively, of the TMP values.
There are discrepancies concerning the time frame for the biodegradation of different biopolymers, and most researchers have not provided information on biogas yield. Bátori et al. [36] found that some biopolymers, such as starch, cellulose, pectin, and poly(hydroxyalkanoate), can be degraded at hydraulic retention times commonly used in biogas plants. Shin et al. [39] reported that 89% of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHB/HV; 92/8, w/w) could be degraded within 20 days under anaerobic mesophilic conditions. Similarly, Noda et al. [33] found that 80% of 14-C-labeled poly(3-hydroxybutyrateco-3-hydroxyoctanate) biodegraded after 25 days under anaerobic conditions at 37 • C. Yagi et al. [35] found that during mesophilic (37 • C) anaerobic degradation, PHB was over 90% biodegraded in 10 days, whereas PLA was only 7% biodegraded in 90 days, and PBS did not degrade. Kolstad et al. [34] tested the degradability of a commercially available PLA product at two temperatures: 21 • C (under simulated landfill conditions) and 35 • C. The duration of the tests was 13 months (390 days) and 170 days, respectively. The authors found that, in a year-long psychrophilic test, the amorphous and semicrystalline PLA did not produce a significant volume of biogas. At 37 • C, it was predicted that amorphous PLA would yield approximately 189 L/kg (40% of the theoretical potential), whereas it was observed that the semicrystalline samples did not generate a significant volume of methane.

Microscopic Analyses and Topography of the Investigated Materials
The small amount of biogas produced by the bio-based materials is connected with the fact that, until 365 days of anaerobic degradation had passed, pieces of the foils were still visible in the inoculum, and these fragments only started to show damage. Polymer degradation can be determined based on the changes in the surface, e.g., formation of holes and/or cracks, and changes in color or roughness parameters. Moreover, thermal properties (DSC) or the results of FTIR analyses can provide information about the structural changes in the material [40].
The foils used in the present study came from commonly available bags for waste collection. Initially, each of the foils had a green color and was smooth. Microscopic analyses at 100-fold magnification showed no changes after 1 year of degradation of the F PLA material, but analyses at 1000-fold revealed some pores in the material structure ( Figure 2). Analyses of surface topography indicated that, after long-term anaerobic degradation, the structure of F PLA had become more heterogeneous than that of the raw material ( Figure 3). The distance between the valleys and peaks decreased after degradation, which may have been caused by diffusion of water into the material structure and may indicate that the foil's thickness was gradually decreasing and it was being degraded [41].  In contrast to F PLA , the FS material changed visibly after 1 year of degradation, and individual cracks and fissures were visible in its structure (Figure 2). These changes corresponded to slightly higher biogas production from F S than from F PLA . A change in the color of the material was also observed. Such changes in the color of a polymer may be considered an important indicator of the biodegradation process [42]. Lee et al. [43] observed that, during anaerobic degradation of a foil consisting of a mixture of PLA and pure lactic acid, its color changed from transparent to white after 10 days of the process, whereas a foil consisting of pure PLA did not change color during this time. In the study present here, the analyses of F S surface topography indicated that, after degradation, the structure of the material became more homogeneous (Figure 3). The change in the color of the bio-based product may be one of the indicators of the biodegradation of the polymer. Fortunati et al. [44] observed changes of color of the PLA material during composting due to hydrolytic degradation of the polymer, which led to a change in the refraction index. This was caused by water absorption and/or the presence of hydrolysis product. The same results were obtained by Arrieta et al. [45] during composting of PLA and plasticized PLA/PHB films. Moreover, the authors suggested that an increase in lightness of plasticized films may be caused by loss of the plasticizer and the compression of macromolecular chains of polymer. The color change of bio-based products may also correspond to the embrittlement of materials, which is associated with increase in crystallinity [46].
. Polarizing and digital microscopic images of raw foil materials and of foil materials after a 365-day anaerobic mesogradation test.
. Topography of raw foil materials (a,c,e) and of foil materials after a 365-day (b,d,f) anaerobic mesophilic degrast.

Differential Scanning Calorimetry (DSC) Measurements
Regarding the DSC curve of raw foil of FPLA before degradation, the cold crystallization peak was observed at 75 °C. After one-year degradation, this peak was not noted, which may indicate the hydrolysis of FPLA and the rapid increase in polymer matrix crystallinity [47]. A shift in the melting point from 166 °C (FPLA before degradation) to 164 °C Microscopic analyses of F OXO did not show any changes in the foil's structure (Figure 2), whereas an analysis of surface topography showed a decrease in the height of the peaks and the depth of the valleys on the material surface ( Figure 3). This may have been caused by washing away the pro-oxidant additive.

Differential Scanning Calorimetry (DSC) Measurements
Regarding the DSC curve of raw foil of F PLA before degradation, the cold crystallization peak was observed at 75 • C. After one-year degradation, this peak was not noted, which may indicate the hydrolysis of F PLA and the rapid increase in polymer matrix crystallinity [47]. A shift in the melting point from 166 • C (F PLA before degradation) to 164 • C (F PLA after degradation) was observed. Moreover, the enthalpy of the melting process decreased by about 2 J/g. The decrease of F PLA melting point during degradation may be connected with molecular mass reduction [48]. The glass transition temperature increased after degradation from 55 • C to 66 • C, and no enthalpy changes were observed (Figure 4).
Regarding raw foil of F S before degradation, the three melting points at 64 • C, 118 • C, and at 152.8 • C were observed (Figure 4). Aldas et al. [49] reported that the melting point in starch-based material Mater-Bi at 56.3 • C and 107.3 • C corresponded to poly(ε-caprolactone) (PCL) and poly(butylene adipate-co-terephthalate) (PBAT) addition, respectively. Whereas a melting point at ca. 150.3 • C refers to the melting of the plasticized starch fraction [49,50]. Abdullah et al. [51] found that glass transition temperature and melting temperature of starch-based bioplastics decrease with the decrease of starch to glycerol ratio (glycerol is a common plasticizer for producing starch-based bio-based products). In the presented study, after one-year degradation of F S , a shift of all peaks of the DSC curve was observed. However, the area under both curves was similar, which indicated no enthalpy changes for F S before degradation and after the process. the presented study, after one-year degradation of FS, a shift of all peaks of the DSC was observed. However, the area under both curves was similar, which indicated thalpy changes for FS before degradation and after the process.
DSC analyses for FOXO material (in raw material and after one-year degra showed typical DSC curves of polyethylene, without substantial changes due to p dant additive. Contant-Rodrigo [52], during thermal characterization of polypro with the addition of pro-oxidant, also showed that the additive did not modify t curve. In the presented study, the DSC curve of the material after the long-term d tion did not change. Melting process was in the range from 114 °C to ca. 128 °C. Th ing point was observed at 124 ± 0.1 °C. A slightly lower melting point value (117was obtained by Benitez et al. [53] for linear low-density polyethylene.

FTIR Spectra
The FTIR spectra of investigated foils allowed to detect their chemical comp before and after long-term degradation ( Figure 5). The spectrum of raw material showed typical bands for pure PLA. The peak between 3612 and 3000 cm −1 indica drogen-bonded (intra-and intermolecular) -OH groups. The bands located at 296 cm −1 corresponded to asymmetric and symmetric vibrations of the -CH3 groups. Th at 1710 cm −1 represented asymmetric stretching of carbonyl C=O groups by lactide which may indicate the amorphous phase of PLA. The peaks at 1263, 1133, and 10 corresponded to stretching vibrations of the C-O-C and -CH-O-groups. The band cm −1 combined contributions of both -CH3 rocking and deformation of the carb OH ... H groups [55]. At 874 and 727 cm −1 , the O-CH-CH3, esters and/or C-C, and vibrations of -CH3 groups were noted. After one-year anaerobic degradation, no s DSC analyses for F OXO material (in raw material and after one-year degradation) showed typical DSC curves of polyethylene, without substantial changes due to prooxidant additive. Contant-Rodrigo [52], during thermal characterization of polypropylene with the addition of pro-oxidant, also showed that the additive did not modify the DSC curve. In the presented study, the DSC curve of the material after the long-term degradation did not change. Melting process was in the range from 114 • C to ca. 128 • C. The melting point was observed at 124 ± 0.1 • C. A slightly lower melting point value (117-119 • C) was obtained by Benitez et al. [53] for linear low-density polyethylene.

FTIR Spectra
The FTIR spectra of investigated foils allowed to detect their chemical composition before and after long-term degradation ( Figure 5). The spectrum of raw material of F PLA showed typical bands for pure PLA. The peak between 3612 and 3000 cm −1 indicated hydrogen-bonded (intra-and intermolecular) -OH groups. The bands located at 2964-2880 cm −1 corresponded to asymmetric and symmetric vibrations of the -CH 3 groups. The peak at 1710 cm −1 represented asymmetric stretching of carbonyl C=O groups by lactide [45,54], which may indicate the amorphous phase of PLA. The peaks at 1263, 1133, and 1098 cm −1 corresponded to stretching vibrations of the C-O-C and -CH-Ogroups. The band at 931 cm −1 combined contributions of both -CH 3 rocking and deformation of the carboxylic -OH ... H groups [55]. At 874 and 727 cm −1 , the O-CH-CH 3 , esters and/or C-C, and rocking vibrations of -CH 3 groups were noted. After one-year anaerobic degradation, no shifts or new peaks appeared in FTIR spectra of F PLA . However, the intensity of all bands increased, indicating minor degradation. The increase in peak corresponding to carbonyl C=O groups is associated with the increase in the number of carboxylic end groups in the polymer chain due to hydrolytic degradation [45]. new peaks appeared in FTIR spectra of FPLA. However, the intensity of all b indicating minor degradation. The increase in peak corresponding to groups is associated with the increase in the number of carboxylic end gr ymer chain due to hydrolytic degradation [45].  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100  100   0  Infrared spectra for the raw material of F S exhibited bands characteristic of plasticized starch. Over the one-year anaerobic degradation, no new peaks appeared in the IR spectra, and transmittance across all peaks slightly changed, indicating minor degradation. The peaks between 3600 and 3100 cm −1 and between 1270 and 900 cm −1 related to O-H stretching groups and to C-O stretching and hydrogen bonding peaks, respectively. Peaks at 1140 and 1103 cm −1 , indicated the C-O stretching of the C-O-H group, which is a typical starch group in hydrogen bonding. The peak at 1016 cm −1 corresponded to the C-O stretching of the C-O-C group of the starch glycosidic bonds [56]. The peak located at 727 cm −1 represented four or more adjacent methylene (-CH 2 -) groups. The bands at 2917 cm −1 corresponded to C-H stretching in aliphatic and aromatic groups. The bands at 1715, 1272 cm −1 , and 1019 cm −1 corresponded to the carbonyl groups C=O, the C-O link, and the stretching of phenylene groups, respectively.
Regarding F OXO , the FTIR spectrum was typical for polyethylene. The difference was a small band at 1630 cm −1 corresponding to a double bond (or aromatic rings), which was indicated probably as a result of surface antioxidant addition. This band was not noted after 365 days of anaerobic degradation, and the F OXO spectrum was as for pure PE. This means that antioxidant additive was washed away or assimilated by bacteria [57]. The peaks located at 2894 and 2846 cm −1 belong to C-H stretching asymmetric and symmetric vibrations. The band at 1464 cm −1 related to CH 2 scissoring groups, whereas the bands at 720 cm −1 and 717 cm −1 indicated CH 2 rocking vibration.
In summary, due to the development of the market of bio-based products, their waste may appear in the waste management system. As was mentioned, such kind of waste can be found in different streams, i.e., mixed municipal waste and selectively collected plastic waste or biowaste. Given the priorities in the waste management hierarchy, bio-based products should be collected with biowaste and biologically treated. Thus, researchers and future studies should focus on searching for the most optimal conditions for biodegradation of bio-based products and potential microorganisms that have the capability to degrade these polymers. The knowledge about the microbiological community structure involved in the biodegradation and the pathways of biodegradation of bio-based materials during composting or anaerobic digestion would provide valuable information. For waste management and end-of-life scenarios, it is essential to provide as much information as possible to create a database on the biodegradability of commercially available bio-based materials. This information may also be useful for assessing regulations for the management of bio-based materials.

Conclusions
During one year under mesophilic anaerobic conditions, F OXO did not degrade (no biogas was produced). Moreover, no microscopic changes were found in the foil structure. The bio-based materials (F S and F PLA ) produced small amounts of biogas, 25.2 and 30.4 L/kg VS for F PLA and F S , respectively, whereas TMP indicated that even 610 and 577 L/kg VS could be obtained. The structure of bio-based foils started to show damage. However, the individual cracks and fissures were visible in the structure of F S . This indicates that they were in the initial phase of degradation. Although the manufacturers labeled these commercially available bio-based products as biodegradable, this study found that they did not disintegrate even after 1 year of mesophilic anaerobic degradation, indicating that the foils would persist for an unknown but lengthy amount of time. Thus, providing guidelines for bio-based foil treatment remains a challenge in waste management.