Environmental Impacts of Building Construction Using Cross-laminated Timber Panel Construction Method: A Case of the Research Building in Kyushu, Japan

: In Japan, there has been an increase in the number of buildings built using cross-laminated timber (CLT) in order to utilize the abundant forest resources in the country. However, no studies have evaluated the environmental impact of the construction of CLT buildings in Japan. This study evaluates the environmental impacts from the start of construction to the completion of a real CLT building in Kumamoto city, Kyushu region, southern Japan. We investigated the input of the materials and energy used in the construction of the building. The environmental impact categories evaluated include climate change, ozone layer depletion, eutrophication, acidiﬁcation, and photochemical oxidation. We found that the concrete used for the foundations, and the cement-based soil stabilizer used for ground reinforcement accounted for 42% of the greenhouse gas (GHG) emissions. The construction site was previously used as a seedbed ﬁeld, necessitating ground reinforcement. Furthermore, the large foundations were designed in order to raise the low height of the wooden structure from the ground level. Developing and applying methods with lower environmental impacts for ground reinforcement and building foundations is recommended. In addition, we found that by using biomass-derived electricity in CLT manufacturing, the environmental impacts of CLT manufacturing could be reduced, thus reducing the environmental impacts of the entire building. The biogenic carbon ﬁxed in the wooden parts during the building usage accounted for 32% of the total GHG emissions of the building construction. Since this biogenic carbon will be released to the atmosphere at the end-of-life stage of the building, a long-term usage of the CLT buildings and / or reuse of the CLT is recommended. of of a real CLT and, based on suggest directions for an of CLT


Introduction
Wooden buildings are a common part of architecture in Japan. Wooden buildings account for 42% of the floor area of new housing and buildings in Japan [1]. In 2010, the government introduced the "Act for Promotion of Use of Wood in Public Buildings", which aims to establish a practice of using timber for building widely in society. Under the Act, the government and related organizations take initiatives for using wood for public buildings, etc. The main policy of the Act states that "the Government to construct all the public buildings of three stories or lower with wood structure in principle" [2]. The remainder of this paper is structured as follows. Section 2 presents Materials and Methods, including the description of the building, system boundaries, and the methodology used for the environmental impact assessment in this study, as well as data collection. Section 3 presents the Results, including the impacts associated with the various stages of the construction process. Discussion (including recommendations for environmentally conscious design) and Conclusions are presented in Sections 4 and 5.

Surveyed CLT Building
The evaluation target was a building intended for conducting research and experiments at the Kyushu branch of the Forestry Research Institute. Figure 1 shows the exterior and interior of the CLT building after completion, and Figure 2 shows the floor plan of the first and second floors. The first floor was mainly used as laboratories, and to accommodate experimental equipment. The second floor was mainly used as a library.
Sustainability 2020, 12, 2220 3 of 14 The remainder of this paper is structured as follows. Section 2 presents Materials and Methods, including the description of the building, system boundaries, and the methodology used for the environmental impact assessment in this study, as well as data collection. Section 3 presents the Results, including the impacts associated with the various stages of the construction process. Discussion (including recommendations for environmentally conscious design) and Conclusions are presented in Sections 4 and 5.

Surveyed CLT Building
The evaluation target was a building intended for conducting research and experiments at the Kyushu branch of the Forestry Research Institute. Figure 1 shows the exterior and interior of the CLT building after completion, and Figure 2 shows the floor plan of the first and second floors. The first floor was mainly used as laboratories, and to accommodate experimental equipment. The second floor was mainly used as a library. The remainder of this paper is structured as follows. Section 2 presents Materials and Methods, including the description of the building, system boundaries, and the methodology used for the environmental impact assessment in this study, as well as data collection. Section 3 presents the Results, including the impacts associated with the various stages of the construction process. Discussion (including recommendations for environmentally conscious design) and Conclusions are presented in Sections 4 and 5.

Surveyed CLT Building
The evaluation target was a building intended for conducting research and experiments at the Kyushu branch of the Forestry Research Institute. Figure 1 shows the exterior and interior of the CLT building after completion, and Figure 2 shows the floor plan of the first and second floors. The first floor was mainly used as laboratories, and to accommodate experimental equipment. The second floor was mainly used as a library. The building was planned as a replacement for the old experimental building, which was damaged by the 2016 Kumamoto earthquake and became unusable. The construction of the building was started in 2017 and completed in 2018. The building has a total floor area of 1424.23 m 2 . This was the first research and experiment building in Japan to use a CLT panel construction method. The interior of the passage inside the building was finished using CLT as a structural material. Examples of the cross section of the external and internal walls are shown in Figure 3. The CLT-exposed indoors was designed to be thicker than the necessary thickness for a structural material. This was done in order to prevent a fire and to ensure sufficient evacuation time considering the burning rate in case of a fire. The interior and the ceiling of the laboratory were finished with a gypsum board in order to prevent the spread of a fire indoors.   Table 1 summarizes the specifications of the building. The project cost amounted to approximately 670 million yen (approximately 6 million USD based on 111 JPY / USD), which was higher than that for regular Japanese houses. The thermal insulation and earthquake resistance of the building meet the Japanese building standards; therefore, the specifications of the building are considered to be stricter than those of other countries.  The building was planned as a replacement for the old experimental building, which was damaged by the 2016 Kumamoto earthquake and became unusable. The construction of the building was started in 2017 and completed in 2018. The building has a total floor area of 1424.23 m 2 . This was the first research and experiment building in Japan to use a CLT panel construction method. The interior of the passage inside the building was finished using CLT as a structural material. Examples of the cross section of the external and internal walls are shown in Figure 3. The CLT-exposed indoors was designed to be thicker than the necessary thickness for a structural material. This was done in order to prevent a fire and to ensure sufficient evacuation time considering the burning rate in case of a fire. The interior and the ceiling of the laboratory were finished with a gypsum board in order to prevent the spread of a fire indoors. The building was planned as a replacement for the old experimental building, which was damaged by the 2016 Kumamoto earthquake and became unusable. The construction of the building was started in 2017 and completed in 2018. The building has a total floor area of 1424.23 m 2 . This was the first research and experiment building in Japan to use a CLT panel construction method. The interior of the passage inside the building was finished using CLT as a structural material. Examples of the cross section of the external and internal walls are shown in Figure 3. The CLT-exposed indoors was designed to be thicker than the necessary thickness for a structural material. This was done in order to prevent a fire and to ensure sufficient evacuation time considering the burning rate in case of a fire. The interior and the ceiling of the laboratory were finished with a gypsum board in order to prevent the spread of a fire indoors.   Table 1 summarizes the specifications of the building. The project cost amounted to approximately 670 million yen (approximately 6 million USD based on 111 JPY / USD), which was higher than that for regular Japanese houses. The thermal insulation and earthquake resistance of the building meet the Japanese building standards; therefore, the specifications of the building are considered to be stricter than those of other countries.   Table 1 summarizes the specifications of the building. The project cost amounted to approximately 670 million yen (approximately 6 million USD based on 111 JPY/USD), which was higher than that for regular Japanese houses. The thermal insulation and earthquake resistance of the building meet the Japanese building standards; therefore, the specifications of the building are considered to be stricter than those of other countries.

System Boundary
The system boundaries in this study were defined as cradle-to-installation, from the production of the construction materials to up to the construction stage of the building ( Figure 4). According to ISO21930:2017 [19], which is an international standard for building life-cycle assessment, the production stage consists of extraction and upstream production (A1), transport to factory (A2), and manufacturing (A3). All these were included in the system boundary. Since the construction stage consists of transport to site (A4) and installation (A5), both of these were also included in the system boundary. The installation included ground reinforcement work, concrete work, CLT work, and exterior work. ISO21930:2017 defines cradle-to-installation assessment as covering the mandatory production stage (A1 to A3), and both transport to construction site and construction installation on site (A4 and A5) [19], and this study adopted this definition.

Environmental Impact Assessment Method
In this study, we assessed the environmental impacts of climate change, ozone depletion, eutrophication, acidification, and photochemical oxidation associated with constructing the CLT building. All of these impact categories are required by ISO21930:2017 [19]. Table 2 shows each impact category and the characterization model adopted in this study. The values of the 100-year  In the use stage of the building, energy is further consumed by using, for example, air conditioners, and luminaires. However, as the surveyed building was intended for conducting research and experiments, a variety of facilities and equipment will need be operated in the use stage. Hence, the environmental impacts of the use stage of the building will differ from those of regular office and apartment buildings. However, quantifying energy consumption for this building involved high uncertainties associated with the uncertainties surrounding the type of research to be carried out in the building. For this reason, this study focused on the environmental impacts of up to the construction stage, and other life-cycle stages were excluded from the system boundary. For the same reason, the production of machines and electrical equipment installed in the building was treated as being outside of the system boundaries. Further, environmental impacts from the commute of the construction workers were also excluded.

Environmental Impact Assessment Method
In this study, we assessed the environmental impacts of climate change, ozone depletion, eutrophication, acidification, and photochemical oxidation associated with constructing the CLT building. All of these impact categories are required by ISO21930:2017 [19]. Table 2 shows each impact category and the characterization model adopted in this study. The values of the 100-year factors of IPCC [20] were used as characterization factors of climate change. The impacts on ozone depletion were evaluated by the characterization factors of World Meteoritical Organization (WMO) [21], widely adopted internationally. Eutrophication, acidification, and photochemical oxidation are local or regional environmental issues. An environmental impact assessment method, LIME2 [22], is typically used in Japan to provide a characterization models for a variety of impact categories considering the local geographical and environmental situation. Therefore, characterization factors of LIME2 were used for environmental impact categories of eutrophication, acidification, and photochemical oxidation in this study.

Inventory Data Collection
Data on the daily material delivery were collected at the construction site. This included not only the materials directly used for the construction of the building, but also materials consumed at the site and the excess materials ordered to avoid a potential material shortage. All of these were included in the inventory data, since they were prepared for the construction. Inputs less than 1% of the total weight were cut off. For the temporary materials (such as pipes for temporary scaffolding) that could be reused at other construction sites, only fuel consumption due to transportation was included in the inventory data. Table 3 summarizes the amount of materials used. This corresponds to the production stage (A1-A3) in Figure 4. Our findings showed that the weights of reinforcing steel rod in concrete (deformed bar), the cement-based soil stabilizer used in the foundation work, and crusher-run stone used in the external construction work, were large. Hot-dip galvanized steel sheet was used for the exterior, such as the roof. Based on the above data, and on the maximum loading capacity of trucks and the loading site (material procurement location), the fuel consumption was calculated at the time of material delivery.
At the construction site, several machines were used. For example, heavy machinery was used for ground reinforcement works and lifting equipment was used for installing CLT panels. The environmental impacts caused by the fuel consumption in the heavy machinery were evaluated based on the amount of the fuel delivered to the construction site. The electricity consumed at the construction site was measured weekly by checking the specially installed power meter. Table 4 shows the amount of materials transported to the construction site, the amount of energy consumed during construction, and the amount of waste to be disposed. This corresponds to the construction stage transport (A4) and building works (A5) in Figure 4. In terms of transportation volume, heavy trucks such as 10 t trucks accounted for the most significant volume. In terms of fuel consumption in Installation (A5), diesel oil was the most calorific in the calorie base. Diesel oil was mainly consumed by heavy machinery used in ground reinforcement works, foundation works, CLT construction works, and exterior construction works.  [23], a Japanese process-based inventory database, for the background data. Environmental impacts of roundwood production were adopted from Nakano, Shibahara, Nakai, et al. [24], and re-calculated using IDEA ver.2.3 for assessing all impact categories of this study, and maintaining the consistency of the background data. The environmental impacts of the CLT manufacturing and precutting processes were adopted from the Japanese representative LCA data [25]. The amount of biogenic carbon fixed in the CLT product was accepted as 585 kg-CO 2 e/m 3 -CLT [25]. Table 5 and Figure 5 show the calculation results for each impact category, and the breakdown by item. The total GHG emissions until completion (A1-A5) were 1.01 × 10 6 kg-CO 2 e. As for the total floor area of the building (1424.29 m 2 ), the GHG emissions amounted to 7.11 × 10 2 kg-CO 2 e/m 2 . The largest GHG emissions-2.35 × 10 5 kg-CO 2 e or 23%-were from the concrete used for building the foundations. The second largest GHG emissions-1.91 × 10 5 kg-CO 2 e or 19%-were associated with the soil stabilizer (cement). The GHG emissions during CLT production accounted for the third highest GHG emissions, at 17% (1.74 × 10 5 kg-CO 2 e). The impact of on-site energy consumption and waste disposal due to on-site works (A5) was small, at 2% (1.87 × 10 4 kg-CO 2 e). The impact of material transportation (A4) was also small (but not negligible), at 4% (4.29 × 10 4 kg-CO 2 e). The impacts of the building construction on acidification showed the same breakdown as GHG emissions. However, the proportion of the impacts caused during CLT production (30% or 1.40 × 10 2 kg-SO 2 e) was higher than the concrete (17% or 7.92 × 10 kg-SO 2 e) and the soil stabilizer (14% or 6.53 × 10 kg-SO 2 e). The impact on the ozone depletion was the greatest, with the contribution of other steel, mainly hot-dip galvanized steel sheet used for the exterior, at 24% (8.41 × 10 −3 kg-CFC11e). In terms of impacts on eutrophication and photochemical oxidation, the contribution of plywood was the largest, at 68% (7.05 kg-PO 4 3− e) and 32% (4.95 kg-C 2 H 4 e), respectively.

Environmental Impacts of the CLT-Related Structural Construction
We analyzed the environmental impacts of the CLT-related structural construction work. which were calculated based on the amount of materials delivered to the construction site during the building works ( Figure 6). The results showed that 72% of GHG emissions were due to CLT panel manufacturing, with gypsum board and iron products accounting for 11% each. The pre-cut CLT panels were lifted and installed to their designated place one by one with a crane, which consumed diesel oil; however, the associated GHG emissions were as low as 2%. In other impact categories, the impact of diesel oil used for the lifting equipment was similarly small.

Environmental Impacts of the CLT-related Structural Construction
We analyzed the environmental impacts of the CLT-related structural construction work. which were calculated based on the amount of materials delivered to the construction site during the building works ( Figure 6). The results showed that 72% of GHG emissions were due to CLT panel manufacturing, with gypsum board and iron products accounting for 11% each. The pre-cut CLT panels were lifted and installed to their designated place one by one with a crane, which consumed diesel oil; however, the associated GHG emissions were as low as 2%. In other impact categories, the impact of diesel oil used for the lifting equipment was similarly small.
In the acidification category, most of the impacts were caused by the CLT panel manufacturing, similar to the GHG emissions. The CLT manufacturing also resulted in major impacts on the ozone layer depletion, eutrophication and photochemical oxidation. However, the impacts of the gypsum board were also significant. In particular, the gypsum board accounted for 43% of the impact on the ozone layer depletion, and for 25% and 23%, of the impacts on eutrophication and photochemical oxidation, respectively.

Environmental Impacts of the CLT-related Structural Construction
We analyzed the environmental impacts of the CLT-related structural construction work. which were calculated based on the amount of materials delivered to the construction site during the building works ( Figure 6). The results showed that 72% of GHG emissions were due to CLT panel manufacturing, with gypsum board and iron products accounting for 11% each. The pre-cut CLT panels were lifted and installed to their designated place one by one with a crane, which consumed diesel oil; however, the associated GHG emissions were as low as 2%. In other impact categories, the impact of diesel oil used for the lifting equipment was similarly small.
In the acidification category, most of the impacts were caused by the CLT panel manufacturing, similar to the GHG emissions. The CLT manufacturing also resulted in major impacts on the ozone layer depletion, eutrophication and photochemical oxidation. However, the impacts of the gypsum board were also significant. In particular, the gypsum board accounted for 43% of the impact on the ozone layer depletion, and for 25% and 23%, of the impacts on eutrophication and photochemical oxidation, respectively. In the acidification category, most of the impacts were caused by the CLT panel manufacturing, similar to the GHG emissions. The CLT manufacturing also resulted in major impacts on the ozone layer depletion, eutrophication and photochemical oxidation. However, the impacts of the gypsum board were also significant. In particular, the gypsum board accounted for 43% of the impact on the ozone layer depletion, and for 25% and 23%, of the impacts on eutrophication and photochemical oxidation, respectively.

Environmentally Conscious Design of the CLT Building
In this study, the cement-based soil stabilizer used for ground reinforcement and concrete used for the foundation accounted for 34% of the GHG emissions associated with the construction of the CLT building, in total. By adding the impact of the deformed steel bars used during construction, this amount will be increased to 53%. The production of these materials also had a significant impact on the acidification category. The significance of these impacts was due to the following reasons. First, the construction site was formerly used as a seedbed field, hence ground reinforcement was necessary. Second, large foundations were designed in order to raise the low height of the wooden structure from the ground level. This was necessary for the stable installation of the research equipment and to comply with the requirement for raising the wooden structure to a height of 1 m above ground level in order to prevent decay or termite damage, as stipulated in the Housing Quality Assurance Act [26].
Using an alternative, non-cement based, ground reinforcement method, and an alternative design for the building foundation, has the potential to reduce these environmental impacts; hence, developing and applying these methods is recommended. In addition, plywood used as the concrete foundation formwork showed a certain contribution to the impact categories of the ozone layer depletion, eutrophication, and photochemical oxidation, hence plywood reuse should be considered to reduce the environmental impacts.
Note that this study focused on the production stage only; therefore, an alternative method to meet the above-mentioned recommendations must keep other performances, such as thermal insulation, to avoid an unintended shift in environmental impacts from the production stage to use and end-of-life stages.

Environmental Impact Reduction of CLT Manufacturing
GHG emissions from CLT manufacturing accounted for 17% of the entire building's impact. The environmental impact data of CLT manufacturing used in the study were based on the Japanese representative LCA data [25], with grid electricity and steam provided by biomass fuel used during the manufacturing process. However, there are currently CLT manufacturing plants in Japan that have introduced a cogeneration system using biomass fuel, so it is possible to manufacture CLT using biomass-derived electricity.
When using biomass-derived electricity in the CLT manufacturing process, the GHG emissions were reduced by 5% (Figure 7). The impact on acidification in this case was also reduced by 5%, and the impact on photochemical oxidation was reduced by 7%. Since the environmental impacts of the CLT manufacturing accounted for a large proportion of the impacts of the series of construction works considered in this study, it can be concluded that reducing the environmental impacts of the CLT manufacturing process is highly effective in reducing the overall environmental impacts of the CLT building construction.

Uncertainty Analysis
Fresh concrete must be changed to a mixing ratio and/or ingredient to maintain its mechanical properties, such as strength and fluidity, in the winter (daytime temperatures of 4 • C or less) and in the summer (daily average temperatures of 25 • C or more). In practice, it is usual to schedule the concrete laying work to avoid these seasons, to prevent a deterioration in concrete quality and an increase in cost. In this case, the foundational concrete laying work was carried out in September and October. However, owing to the limited construction period, the concrete laying work may be carried out in summer and winter. However, the environmental impacts may increase under these conditions.

Uncertainty Analysis
Fresh concrete must be changed to a mixing ratio and/or ingredient to maintain its mechanical properties, such as strength and fluidity, in the winter (daytime temperatures of 4 °C or less) and in the summer (daily average temperatures of 25 °C or more). In practice, it is usual to schedule the concrete laying work to avoid these seasons, to prevent a deterioration in concrete quality and an increase in cost. In this case, the foundational concrete laying work was carried out in September and October. However, owing to the limited construction period, the concrete laying work may be carried out in summer and winter. However, the environmental impacts may increase under these conditions.
Further, the environmental impacts caused by the use of electric furnace steel (e.g., deformed bars) mainly depend on the environmental impact of electricity used in the electric furnace. In this study, the electric furnace steel was evaluated assuming the use of grid electricity in 2017. In 2017, Japan's electricity mix was heavily fossil-fuel-based (81%) and most of the nuclear power plants were under temporary shutdown [27]. Renewable energy accounts for 16% of energy use, but the introduction of the Feed-in-tariff policy has increased the installation of renewable energy facilities, such as solar photovoltaics and wind power [27]. Therefore, the environmental impacts of these electric furnace products can be changed based on the operational status of nuclear power plants and the spread of renewable energy.
With regard to CLT, Japan is hot and humid in summer and cold in winter, with low humidity in some areas. Under high humidity conditions, wood swells, especially in the cross direction of the fibers, thus requiring time and energy to adjust the dimensions of the CLT panels when installing them at the construction site. The dimensions of the CLT panels, however, are adjusted considering the environmental conditions before shipping to the site. Therefore, this does not influence the results.

Biogenic Carbon Content
The amount of biogenic carbon fixed in the CLT product is 5.85 x 10 2 kg-CO2e/m 3 -CLT [25]. Since the building used 5.51 × 10 2 m 3 of CLT panels, it stored 3.22 × 10 5 kg of CO2e. This carbon remains fixed for as long as the panels are used in buildings. This represents 32% of the total GHG emissions until the building construction. Therefore, if the impacts of the temporary fixation of biogenic carbon are included in the assessment, the overall GHG emissions will be lower. The GHG emissions per area amounted to 7.11 × 10 2 kg-CO2e/m 2 ; however, if the biogenic carbon storage impact is included, Further, the environmental impacts caused by the use of electric furnace steel (e.g., deformed bars) mainly depend on the environmental impact of electricity used in the electric furnace. In this study, the electric furnace steel was evaluated assuming the use of grid electricity in 2017. In 2017, Japan's electricity mix was heavily fossil-fuel-based (81%) and most of the nuclear power plants were under temporary shutdown [27]. Renewable energy accounts for 16% of energy use, but the introduction of the Feed-in-tariff policy has increased the installation of renewable energy facilities, such as solar photovoltaics and wind power [27]. Therefore, the environmental impacts of these electric furnace products can be changed based on the operational status of nuclear power plants and the spread of renewable energy.
With regard to CLT, Japan is hot and humid in summer and cold in winter, with low humidity in some areas. Under high humidity conditions, wood swells, especially in the cross direction of the fibers, thus requiring time and energy to adjust the dimensions of the CLT panels when installing them at the construction site. The dimensions of the CLT panels, however, are adjusted considering the environmental conditions before shipping to the site. Therefore, this does not influence the results.

Biogenic Carbon Content
The amount of biogenic carbon fixed in the CLT product is 5.85 x 10 2 kg-CO 2 e/m 3 -CLT [25]. Since the building used 5.51 × 10 2 m 3 of CLT panels, it stored 3.22 × 10 5 kg of CO 2 e. This carbon remains fixed for as long as the panels are used in buildings. This represents 32% of the total GHG emissions until the building construction. Therefore, if the impacts of the temporary fixation of biogenic carbon are included in the assessment, the overall GHG emissions will be lower. The GHG emissions per area amounted to 7.11 × 10 2 kg-CO 2 e/m 2 ; however, if the biogenic carbon storage impact is included, it would be reduced to 4.85 × 10 2 kg-CO 2 e/m 2 . Nevertheless, if the CLT panels were decomposed at the end-of-life stage of a building, the stored biogenic carbon will be released into the atmosphere. Hence, it is recommended to utilize the CLT building for a long time and/or to reuse the CLT panels used in the construction.

Comparison with Other Studies
Another study investigates the GHG emissions from the construction of a mid-rise CLT office building in the US [4]. According to the study, the total GHG emissions amounted to 0.126 t-CO 2 e/m 2 , including the impact of biogenic carbon storage. In a similar manner, the impacts evaluated for low-rise CLT buildings in Slovenia [5], including the impact of carbon storage, totalled 0.027-0.163 t-CO 2 e/m 2 .
Both are significantly smaller than the result of this study, 4.85 × 10 2 kg-CO 2 e/m 2 . However, the building investigated in this study was a two-story building for research experiments, with the floor plan entirely different from that of high-and mid-rise office buildings, hence the different results achieved in these studies were inevitable. In addition, Japan has stricter seismic standards than other countries and it also has stricter structural requirements, hence the environmental impacts per unit area are considered to have increased. IDEA, The Japanese LCA database, presents the value of wooden buildings for offices as a general building value in Japan, which is 0.422 t-CO 2 e/m 2 , without including carbon storage. As a result, the value of this building was higher than that of a general wooden office building in Japan.

Conclusions
In Japan, to utilize the abundant forest resources in the country, the government has promoted the use of wood for buildings, and the number of buildings using CLT has increased. However, the environmental impact of CLT building construction in Japan has not been studied. This study assessed the environmental impacts of cradle-to-installation of CLT building constructed in 2017-2018. The input of materials and energy required for the construction of a two-story research and experiment building in Kumamoto, Kyushu, Japan was investigated. It was clarified that the concrete used for constructing the foundations accounted for 23%, while the cement-based soil stabilizer used for ground reinforcement accounted for 19% of the total GHG emissions. This will be increased to 53% on adding the impact of the deformed bars used for the foundations. The construction site was previously utilized as a seedbed field, which necessitated the need for ground reinforcement. Furthermore, the large foundations were arranged to raise the low height of the wooden structure from the ground level. Therefore, the development and application of methods with lower environmental impacts for ground reinforcement and building foundations are recommended. In addition, it is clarified that the use of biomass-derived electricity in CLT manufacturing could reduce the environmental impacts of the CLT panel manufacturing, thus reducing the environmental impact of the entire building.
The biogenic carbon fixed in the building accounted for 32% of the total GHG emissions of the building construction. The biogenic carbon will be released to the atmosphere at the end-of-life stage of the building; thus, long-term use of the building and/or reusing the CLT panels in other buildings is recommended.