Evaluation of Two Improved Schemes at Non-Aligned Intersections Affected by a Work Zone with an Entropy Method

: The impact of work zones on trafﬁc is a common problem encountered in trafﬁc management. The reconstruction of roads is inevitable, and it is necessary and urgent to reduce the impact of the work zone on the operation of trafﬁc. There are many existing research results on the inﬂuence of highway work zones, including management strategies, trafﬁc ﬂow control strategies, and various corresponding model theories. There are also many research results on the impacts of urban road and subway construction on trafﬁc operation, including construction efﬁciency, economic impact, and travel matrix. However, there are few studies concerning the choice of work zone location, and most previous studies have assumed that the work zone choice was scientiﬁc and reasonable. Therefore, it is reasonable to choose the location of the work zone and to assess whether there is room for improvement in the road form of the work zone, but this remains a research gap. Therefore, we studied a seven-lane main road T-intersection in Xi’an, China, and investigated a work zone located at this intersection that caused a road offset, leading to the non-aligned ﬂow of main trafﬁc. We designed two road improvement schemes and multiple transition schemes, used VISSIM software to evaluate the trafﬁc operation of the two schemes, and used the entropy method to choose the suitability of the two schemes under different conditions. According to the results, in the best case, the driving time, delay, and number of stops are reduced by 44%, 66%, and 92%.


Introduction
Sustainable traffic flows through intersections have long been regarded as the central issue in urban transportation systems. Inbound traffic flows from different directions merge and diverge at intersections, which are often disturbed for various reasons, leading to traffic congestion. The intersection traffic problem not only causes congestion, but also generates air pollution [1] and potential safety hazards [2]. Restriction policies and congestion charges are also results of congestion [3].
Not all intersections are standard, which can be the results of urban scheming, building near the intersection, imbalance between the number of lanes, road markings, and traffic optimization [4][5][6]. Cross intersections [7] and T-intersections [8] are commonly used shapes, whereas roundabouts [9,10] and unconventional intersections [11] are not rarely seen. All these forms of intersections affect traffic operations to different degrees [12]. Many researchers have achieved major successes in improving intersection operations, including methods for the control of left-turn traffic [13], timing of traffic lights [14,15], optimization of road channelization [16], and control of U-turn vehicles [17]. Left-turn traffic has been the focus of much research, because movement in this direction has the greatest impact on the capacity of intersections [18,19]. However, in practice, non-aligned intersections are the result of various circumstances and affect through-traffic operation, where through-traffic operation is often ignored.
The effects of work zones or work zone settlements worsen non-aligned intersections. People often think that traffic congestion at non-aligned intersections is natural or inevitable for objective reasons. In particular, work zones such as subway construction in cities occupying a part of the intersection generate a non-aligned road on the two sides. This kind of work zone remains for a long time, which may be several months or even years, and significantly impacts traffic operation. Therefore, this paper mainly studies the non-aligned intersection caused by work zones occupying intersections. The research on impacts of the work zone concentrates on two major categories. One is the freeway work zone impact, including the influence of capacity [20], work zone influence area [21], and traffic flow prediction models [22], and so forth. The other category is the urban work zone impact, such as the urban travel OD matrix [23], alternative route selection studies [24], and traffic organization management [25], and so forth. While existing studies lack research on the work zone layout and corresponding road geometric layout, few research papers have focused on the rationality of the work zone layout and corresponding road layout. However, the unsuitable work zone settlement and road layout could also have a negative effect on sustainable flow operation. This paper takes the subway work zone of a main road T-intersection in Xi'an, China as an example. Taking the intersection road geometric design and work zone layout as the research content, we propose two work zone layouts and corresponding intersection road layouts when the work zone is set at the intersection. Field survey data and the VISSIM simulation and entropy evaluation method are used to calculate and evaluate the two schemes. The best scheme under different volume combinations is selected, which is of great significance for improving the traffic operation status of intersections and reducing the impact of work zones on urban traffic flow.
The non-aligned intersection discussed in this article is very similar to the dual T-intersection under some circumstances. The two kinds of intersections are easily confused, but they are completely different, as shown in Figure 1. For the dual T-intersection, the operation problem is mainly caused by the distance between two adjacent T-intersections. Two adjacent T-intersections are connected by a short segment and controlled by two traffic lights (one in each intersection), which can be synchronous or asynchronous. The non-aligned intersection mentioned here means that two sides of the roads are not in a straight line at one intersection. No extra segment connects the two sides, and only one traffic light controls the intersection. The main concern under this circumstance is that the through-traffic is offset when passing through the intersection.
The remainder of this article is organized as follows: Section 2 surveys the literature; Section 3 introduces the problem statement, data collection, and calibration of the simulation model; Section 4 introduces solutions and analyzes the performance of two improved schemes; Section 5 discusses the comparison of the two improved schemes with the entropy method, where a final selection matrix is calculated, and the difference between the two schemes is also introduced; and Section 6 concludes the paper. The dual T-intersection (left) is made up of two adjacent T-intersections and two traffic lights controlled separately, whereas a non-aligned intersection (right) is controlled by a single traffic light, and the through-traffic will be offset when passing the intersection.

Highway Work Zone Impact
Non-aligned intersections are the result of various circumstances, such as urban planning, non-aligned road markings, and construction effects. Some results on the impact and corresponding measures of work zones on traffic operation have been reported [20]. Most of the achievements related to work zone influence are focused on highway work zones. Ideally, traffic managers can inform drivers of alternative routes around the work zone in advance of the project location when temporary closures are caused by highway construction. According to a survey conducted in Puerto Rico, when highway drivers pass through a work zone, at least 50% of them are distracted. Furthermore, drivers tend to comply with work-zone speed limits when personnel or heavy equipment are present in the area [21]. The influence of a highway work zone on safety differs between the daytime and nighttime, while older male drivers, the number of lane closures, sidewise crashes, and rainy weather have opposite effects on the severity of crash-related injuries at night compared with crashes in the daytime [26].

Predict and Evaluate Method of Highway Work Zone Impact
Some researchers have developed different methods to predict and evaluate the impact of construction on traffic operation, such as dynamic traffic assignment [27], a five-parameter logistic model that describes the speed-density relationship [22], an optimal nonlinear fitting theory [28], traffic speed versus flow curves, capacity reduction factors, and free-flow speed reduction factors [29]. A bilevel optimization model was proposed for the purpose of minimizing the total travel time of the affected network, involving a link closure and a proposed alternate route for travelers [30]. With a cellular automata model, a highway was divided into the normal area, merging area, and work zone, and the suitable merging length and the appropriate speed limit value were found to be key factors for managing work zone traffic operation [31]. A dynamic control model was used to optimize the signal operations of a new merging system, the lane-based signal merge (LBSM), which uses lane-based signals or variable signs to give drivers in different lanes the right-of-way to proceed through the open lane(s) in a work zone area [32]. A simulation-based analysis is more appropriate for network analysis, for long corridors, for signalized arterials, or for cases in which congestion of the arterial network significantly affects freeway operations [33].

Urban Roads and Subway Work Zone
Besides highway work zone control models, the effects of urban roads and subway construction have also received attention from researchers. In an urban area, a subway work zone has a direct influence on the surrounding road network. Origin Destination (OD) matrix estimation was distributed on a road network with TransCAD to evaluate the traffic organization scheme. The service level of roads and intersections were found to be evaluation indicators that could reduce traffic influence on a road network during subway construction [23]. Combined with the OD distribution principle, the traffic impact of the construction section was analyzed, and the scope of influence was determined. The average delays, queue length, and number of vehicles were selected as three indexes, and VISSIM was used for the simulation of guidance measures to evaluate a better traffic organization scheme [34]. Portable changeable message signs (PCMSs) have been used in work zones to increase legibility. Graphic-aided PCMSs reduced the mean vehicle speed by between 13% and 17% and reduced the speed of passenger cars and trucks significantly differently depending on their locations in a work zone [24]. For reconstruction scheme evaluation, the level of service, negative economic benefit, and traffic environmental impact can be used as analysis and screen indexes. An integrated approach, combined with a dynamic comprehensive evaluation and the analytic hierarchy process was proposed to evaluate traffic organization during highway construction [35]. A survey conducted in New York City showed that the saturation flow rate per lane increased during the work zone. Although the overall approach capacity decreased because a lane was closed, it did not decrease as much as expected [25].

Methods for Work Zone Impact Research
To reduce the negative impact of construction, simulation is one of the best ways to evaluate measurements before their application. A larger system simulation of a Hong Kong microtunneling and pipe-jacking operation concluded that a balance between construction productivity and traffic mobility could be maintained through appropriate truck delivery routes; the timing, sizing, and location of a temporary laydown area; the traffic lane closure distance; and work scheduling [36]. Urban subway construction increased the travel time delays, queue length, fuel consumption, number of forced merges, and roadway accidents. The use of VISSIM to calculate economic losses and to specify systematic work zone schedules and traffic management techniques is necessary [37].
There have recently been some new technologies, such as the intelligent transportation system (ITS) [38][39][40], autonomous vehicles [41], and advanced driving simulator [42]. A multilayer feed-forward artificial neural network (ANN) model could be used to track drivers and vehicles in work zones; the new model performs better than the traditional deterministic queuing model in estimating the travel delay caused by the work zone [43]. One of the future technologies is the connected vehicle. Work zone operation could benefit from this technology as a result of the travel time and its reliability [44]. Some elements of traffic operation are sometimes ignored, such as the impact of construction equipment. Construction equipment can also cause traffic congestion, especially in the bottleneck section; and conversely, unsustainable traffic operation influences the efficiency of the equipment used in the construction schedule [45].
Channelization is a popular and effective method used to reduce traffic problems [46]. An exclusive left-turn lane can be used when left-turn vehicles make up a high proportion of the whole flow [47]. Left-turn lanes can reduce the number of crashes with the opposing through-traffic [48,49]. A left-turn waiting area could also improve the capacity at the intersection [50]. Signalization is another popular control method at intersections [51,52]. An exclusive left-turn phase can be used for heavy left-turn vehicles [53,54]. Left-turn control has been found to significantly improve the operational conditions in China [55][56][57]. Other types of intersections are also used to reduce intersection problems [58].
The learning from the literature review indicates that the existing research results from the influence of highway work zones, including management strategies, traffic flow control strategies, and various corresponding model theories. There are also many research results on the impact of urban road and subway construction on traffic operation, including construction efficiency, economic impact, and travel matrix. However, there are few studies concerning the choice of work zone location, and most previous studies have assumed that the work zone choice was scientific and reasonable. Therefore, it is reasonable to choose the location of the work zone and to assess whether there is room for improvement in the road form of the work zone, but this remains a research gap.

Problem Statement
Xi'an City is taken as an example in this study. At the end of 2018, the population of Xi'an was more than 10 million, and the number of vehicles was 3.25 million [59]. Furthermore, Xi'an has a history of more than 3100 years [60] and massive historical relics, which have resulted in a long construction period in this district [61]. The selected T-intersection is located at the main avenue in the central position of a business area, as shown in Figure 2. The North-South arterial street was a 12-lane road, but it is now a seven-lane road (three lanes Southbound and four lanes Northbound) and connected to the West by a seven-lane collector street (four lanes Westbound and three lanes Eastbound). The distances to adjacent intersections are 270 m, 1100 m, and 720 m to the North, West, and South, respectively.

Data Collection
The collection of real traffic data is necessary to build and calibrate the simulation model in VISSIM. Field data collection was conducted during both peak and valley hours on weekdays and the weekend. According to an investigation, the traffic volume of this intersection on the weekend was much less than that on weekdays. The congestion index in the top 50 cities can be gathered from the AutoNavi Traffic Company [62]. The morning peak appeared from 7:00 a.m. to 9:00 a.m., and the evening peak appeared from 5:00 p.m. to 7:00 p.m. The 24-hour congestion index in Xi'an on 17 January 2019 is shown in Figure 4.  The collected data are as follows: • Speed and types of vehicles in each lane; • Turning vehicles, including left turns and right turns; • Vehicle behavior in the intersection area, especially the South-North vehicle chaos.
The collected volume during the morning peak hour was 6333 veh/h, the volume during the middle noon valley was 5895 veh/h, while the volume during the evening peak hour was 6825 veh/h. Thus, the peak-hour data were selected as the representative. The collected data of the peak periods in 1 h are listed in Table 1. The minimum speed of 0 km/h means that vehicles were stopped and then moved.
The collected data show the following characteristics: 1.
The average speed of Flow i = 3&4 was much higher than that of Flow i = 1&2, and the offset of trajectories strongly affected vehicle operation.

2.
Neither Flow i = 2 nor Flow i = 4 was affected by the offset.

3.
The collector street volume was much less than the arterial street volume, the operation of which was hardly affected by the offset.
The collected trajectories in Figure 5 show the following characteristics: 1.
Northbound vehicles (Flow i = 1&5) were crowded in the intersection area, whereas the Southbound (Flow i = 3&6) and Westbound (Flow i = 2&4) vehicles were hardly affected.

2.
Lane D is a left-turn lane, but through-vehicles used it when other lanes were crowded.

3.
Lane E is a right-turn lane, but left-turn vehicles used it when other lanes were crowded, and some of the left-turn vehicles of lane E detoured via the outside route to avoid the queue. 4.
The outside vehicles operated faster than the inside vehicles; the inside vehicles needed to merge with other vehicles, which caused the delay.

5.
According to the investigation, vehicles of lane G preferred to turn left with a small radius, which was the inside lane when turning left. However, all inner five or six lines of the vehicles had to merge into only one single lane, and because it was difficult to change to the adjacent lane, the inner vehicles moved very slowly. On the basis of observation, the longest time taken by a vehicle of Flow i = 5 to pass through the intersection was about 6 min.

Calibration of the VISSIM Simulation Model
In order to increase the accuracy of the VISSIM simulation model in the following steps, calibration was needed before the sensitivity analysis. The collected traffic data, signal cycles, and road geometry were all calibrated with the collected traffic volume. A standard calibration procedure proposed by previous studies was followed [63][64][65][66]. The parameters of the intersection input into the VISSIM model were as follows: 1.
The ratio of trucks and cars collected from Table 1; 2.
The volume of each flow collected from Table 1; 3.
The speed of each flow collected from Table 1; 4.
The traffic light cycle of the intersection; 5.
The geometric parameters of the intersection. A car-following model, gap-accepting model, and lane-changing model are all available for the VISSIM calibration, but volume capacity is the most commonly used index for calibration. Capacity accuracy is required, and it reflects the VISSIM model accuracy with high sensitivity. The capacity is calculated according to Equation (1): where C denotes the ideal capacity (veh/h), and h t is the average minimum headway (s). An index named Mean Absolute Percent Error (MAPE) can reflect the error between the simulation capacity and collected volume. The MAPE can be calculated by Equation (2): where n denotes six-direction flows, C i v is the VISSIM simulated capacity (veh/h), and C i f is the volume according to investigation (veh/h). The calculated MAPE is displayed in Table 2: The MAPEs of the three periods are −7.3%, −12.9%, and −5.9%, respectively, and these values suggest that the calibration accuracy of the VISSIM model is reasonable. According to previous studies, this error can be accepted [67,68]. Table 2. VISSIM simulation calibration results with collected data for three periods.
Morning peak data

VISSIM Calculation of Operational Measures
The most commonly used indexes for evaluating the improvement of traffic programs with different operational volumes are travel time, delay, and the number of stops [69,70]. The calculation of these indexes is as follows: Travel time. Travel time is the time that it takes for all vehicles to pass through the intersection in the simulation. It is the calculated time from appearance at the upper section of the road to disappearance at the end of the road in the simulation. It can be calculated as Equation (3): where T i denotes the travel time of each direction of traffic flow in Table 1, t ij denotes the travel time of each vehicle, Q i denotes the number of total vehicles of each flow, k = 1 denotes the present intersection situation, and k = 2, . . . , etc. denotes the different improved schemes in the simulation. Delay. A difference always exists between a driver's arrival time and expected time. Traffic interference, traffic control, and management are all possible reasons for a delay. The stop delay and travel delay are both included in the simulation: ∀i = 1, 2, 3, 4, 5, 6 ∀k = 1, 2, . . . , etc., where D i denotes the whole delay of each direction's flow in Table 1, d i1 and d i2 represent the stop delay and travel delay of each flow, respectively, and k = 1 and k = 2, . . . , etc. represent the present and different improved situations, respectively. Number of stops. All standstill situations (speed = 0) in the VISSIM consist of the number of stops, and parking lots or bus stops are not included. It can be calculated by the total number of stops divided by the total number of vehicles: where S k i denotes the average number of stops in Table 1, s ij denotes the number of stops of each vehicle, and Q i is the total number of stops. k = 1, 2, . . . , etc. denotes the present situation and different improved situations.

Solutions
According to Figures 3 and 5, the reason for the congestion at this intersection is the vehicle merge movement on the inner side. Northbound traffic flow is restricted by the road width and lane markings on both sides of the intersection. The driving width is much wider than four lanes when vehicles pass through the intersection. When the front vehicle decelerates or changes a lane, the following vehicles decelerate, change a lane, or attempt to bypass the front vehicle from the outside. This movement can fill the whole intersection area, and then vehicles are slowly squeezed forward.
The core reason for congestion is that a wide intersection area with a maximum 11-lane width narrows into a four-lane width. To reduce the traffic congestion and improve the operational features, channelization is the key solution. Keeping operating vehicles within the lines in the intersection area was the main purpose of the solutions. Figure 6A is the original situation of the intersection before the construction starts. Both sides of the intersection are 12 lanes. Figure 6B is the present situation, in which the work zone occupies two parts of the intersection. The southern part narrows, and the northern part of the intersection is divided. Figure 6C is based on the present situation, with some railing added to narrow the intersection area, restrict vehicle operation to no wider than four lanes, and reduce the inner queue in order to keep vehicles in the lines when passing through the intersection. Figure 6D is another possible solution to improve the intersection. Vehicle operation is kept in a straight line to avoid the influence of the work zone, and then vehicles change direction as the road alignment changes. The 28 m offset of this intersection results in traffic delay and congestion. Would the operation situation improve if the offset was less than 28 m? Is there any relationship between the offset value and traffic operation? In order to find out the relation, different offset situations were evaluated, as shown in Figure 7. The offset value is 28 m, and the different offset values in the simulations were 0∼28 m with a step size of 2 m. The solution of scheme D was also evaluated with different straight lengths after the intersection, followed by a turning direction. The straight length was simulated in a range from 0 to 100 m with a step size of 10 m.

Simulation Result
There were 23 simulations in total: the present situation ( Figure 6B Table 1 were input into VISSIM simulation models to evaluate the different solutions for the same volume. The results are reported below.
It is evident that the present simulation result, group Scheme 1 in the three figures in Figure 7, is much higher than the other situations. The main traffic flows in the six directions are i = 1, i = 3, and i = 5. They all have a similar trend that fluctuates in a small range and almost maintains a straight line. This indicates that the difference resulting from changing the offset value or extending the straight length has little influence on the results. The other three traffic flows have pronounced fluctuations but no clear patterns. This cannot indicate whether the different improvement schemes can promote or inhibit the operation.

Safety Evaluation
A complete evaluation should conclude with an operation and safety evaluation. A commonly used tool, the surrogate safety assessment model (SSAM), is a simulation and analysis project of the Federal Highway Administration (FHWA) to predict the safety of roadways before crashes occur. The SSAM is a software application developed to automatically identify, classify, and evaluate traffic conflicts in the vehicle trajectory data output from microscopic traffic simulation models. The SSAM also has built-in statistical analysis features for conflict frequency and severity measures that can aid analysts in the design of safe traffic facilities [71][72][73]. The safety analysis was applied to 23 schemes with evening peak hour data, where the results are shown below in Table 3. Table 3 shows the safety analysis results of all 23 simulations. Scheme 1, the present situation, shows potential safety problems, especially for the item labeled "Crossing", which takes 362 times, while it takes only four times for all other schemes in total. "Rear End", which is almost 3∼5 times that in the other situations, and "Lane Change" is 8%∼100% higher compared with the rest. However, as this is similar in Figure 7, the improved plans do not show a significant pattern either. Figure 8 and Table 3 show that all improved schemes resulted in a significant improvement compared with the present situation, but it is not easy to distinguish and calculate the best improved scheme. There are no obvious patterns shown in Figure 8 in terms of the travel time, delay, or number of stops. We can now answer the question raised in the last section: Would the operation situation improve if the offset was less than 28 m? Is there any relationship between the offset value and traffic operation? The answer is no. There is no obvious pattern between the offset value and operation features. That is, it is not easy to find a pattern from Figure 8 in order to choose the best performance situation. This means that channelization plays a key role in reducing the traffic chaos in the present situation.  To reduce the workload, two improved schemes, Scheme 16 (offset 28 m) and Scheme 17 (straight length 0 m), were chosen to compare their performances with Scheme 1 (present situation). Schemes 2∼15 are changes based on Scheme 16. Schemes 18∼23 are changes based on Scheme 17, and Schemes 16 and 17 have the least impact on the work zone ( Figure 9). Scheme 16 could be easily retrofitted from the present situation (Figure 6b). Scheme 17 can be achieved by slightly changing the work zone. The rest of the schemes require much more change to the work zone, and these changes are unrealistic and uneconomical. Therefore, Schemes 16 and 17 were selected to evaluate the improvement by comparing them to Scheme 1 in the following part. The collected data in Table 1 were input into three VISSIM models. Schemes 1, 16, and 17 were evaluated, and the results are reported below.

Sensitivity Analysis of Operational Performance
Scheme 17 performs better than Scheme 16, but Table 4 only covers investigated data. In order to cover all operating conditions, all different volume combinations should also be simulated and then be compared. The vehicle composition, turning ratio, and expected speed were the same in all simulations. The South-North direction has four lanes, and the maximum volume is 4570 veh/h, while the North-South direction has three lanes, and the maximum volume is 3430 veh/h according to [74] under service level E. The traffic volume changes within 0.2∼1.0 V/C. The West-East direction has three lanes, and the evening peak hour volume is 651 veh/h, while the middle (noon) valley volume is 178 vhe/h: both are far lower than the stipulated content of 3430 veh/h in [74]. For the West-East direction, 0.025∼0.3 V/C was selected. All volume parameters in VISSIM are shown in Table 5. Traffic light cycles were calculated by Synchro7 for different volume combinations.  The sensitivity analysis can reflect the improvement ratio of Scheme 16 to Scheme 1 and Scheme 17 to Scheme 1. Travel time, delay, and the number of stops are still the three indexes that comprise the sensitivity analysis. The result of Scheme 16 to Scheme 1 is shown in Figure 10: Figure 10 shows the result for the improvement degree of Scheme 16 to Scheme 1. The improvement ratio is calculated by Ratio = (Scheme 16 − Scheme 1)/Scheme 1 * 100%. Figure 10a shows a significant reduction in travel time compared with Scheme 1. The travel time is reduced by 20∼44% of the whole range. Figure 10b shows the delay change result, and the delay changes depend on the volume combinations. The majority of the delay is reduced by 10∼66%. However, the delay increases in five situations, increasing by as much as 22% when the Northbound volume is under 1828 veh/h. Figure 10c shows the improvement in the number of stops. Besides the five situations in which it increases, the majority of the number of stops is reduced from 10% to 92%. The five increased situations are 30.5%, 56.5%, 71.4%, 110.9%, and 232.7%, respectively, and they are all centralized in the same area as that in the previous two figures.
For all ranges, the change in traffic volume has little influence on the performance of the improvement. The performance of the improvement is relatively uniform for the entire range in Figure 10. When the arterial volume is less than 1371 veh/h or more than 3656 veh/h, the improvement is small, or even deteriorates. The improvement from Scheme 16 has a significant effect on the other parts. When both volumes of two roads are small, Scheme 16 has no improvement effect.
The improvement from Scheme 16 shows if the volume increases in either direction. Overall, the improvement of Scheme 16 is clear.   Figure 11 shows the result of Scheme 17 to Scheme 1. Figure 11a shows the change in travel time. Travel time is reduced by 16∼36%, which is a significant improvement. Figure 11b shows the improvement in the delay. The majority is reduced by 10∼66%, while two situations become worse than before, and they are all centralized in the same area as in Figure 10. Figure 11c shows the improvement in the number of stops, and the improvement ratio ranges from 30∼92%, except for two increases.  The impact of volume has a similar trend to that in Figure 10. The improvement decreases when the arterial volume is less than 1371 veh/h or more than 3656 veh/h. Generally, Scheme 17 improves the operation significantly under the majority of conditions. Figures 10 and 11 both show improvement compared with Scheme 1, but no single scheme performs better than the other two schemes under all circumstances. This means that every scheme has its own advantage in different situations. The simulation results are represented with three indexes in the last section, but comparison among schemes with a single standard that includes the weights for the three indexes is needed. The calculation is as follows:

Weight of Three Indexes
where T, D, and S denote travel time, delay, and number of stops, respectively. i = 45 indicates 45 simulation results for each scheme. j = 1, 2, 3 denotes Schemes 1, 16, and 17, respectively. First, the same index of the three schemes needs to be converted into one matrix. In the following steps, T is used as an example. All 45*3 travel time results have been put into one matrix, named T: The other two indexes undergo the same process: Second, in the T matrix, the minimum value of each row is selected, and then the minimum value and its corresponding column number are the output. The 45 minimum values represent the minimum travel time in 45 simulations. A new matrix is generated, named T m .
All three matrices of Equation ( where T m is a matrix that contains the minimum travel time value of each volume combination.
Third, the weights of the three indexes are calculated, and the three indexes are put into one single matrix, Y: To rank the different schemes, it is necessary to rate the simulation result of each traffic condition. The scoring is based on the calculation of the respective weights of the three indexes, namely, travel time, delay, and the number of stops. The entropy method is a common weighting method used to measure value dispersion in decision-making, with regard to the more dispersed, the more differentiated, and the ones with more information. At the same time, indexes should be given higher weight, and vice versa. The entropy method was used to calculate the weights of the three indexes objectively, instead of using artificial weights. In Equation (11), the greater gap between index y(ij) means that y(j) has a greater role. If an index value is the same as another, that means that there is no effect on the final evaluation.
All values should be standardized before the next calculation step since the various indexes are not uniform. Absolute values are converted into relative values, y ij = |y ij |, to solve the problem of homogenization of different qualitative indicators. The calculation is given below: The weight of index j of scheme i is calculated as follows: The entropy value of index j is calculated as follows: where k = 1/ln(n) and satisfies e j ≥ 0. The entropy redundancy is calculated as follows: The weight of each index is calculated as follows: The weight calculation results are shown in Table 6: Table 6. Weights of three indexes.

Schemes Comparison
The corresponding number is chosen from matrix Y to generate a new matrix A = zeros(45 × 3), as follows: where w(j), j = 1 : 3 denotes the weight in Table 6. Each row of Y (Equation 11) has three numbers for three indexes, and each number is the best scheme calculated. For example, the first row in matrix Y is Equation (18) Thus, the first row of matrix A is The columns in matrix A represent Schemes 1, 16, and 17, respectively. The result in the first row is Scheme 17 in matrix A, according to Equation (21). After repeating Equations (17)∼(21), the final matrix T can be generated with the final result: Matrix T contains 45 scheme numbers that represent the best scheme under each condition. Matrix T is transposed into a 9 × 5 matrix, and the final result is plotted in Figure 12:  When the Northbound volume range is 914∼1828 veh/h, Scheme 17 performs much better than Scheme 16; the ratio of the two schemes is 11:2. When the Northbound volume increases from 2285 to 3199 veh/h, Scheme 16 becomes much better than the other two schemes: Scheme 16 occupies 9 blocks, while Scheme 17 only occupies 6 blocks. If the Northbound volume is more than 3656 veh/h, the result of Scheme 17 is similar to that of Scheme 16, and the ratio is 8:7.
The Eastbound volume variation has some influence on the result. When the Eastbound volume is 86 veh/h, Scheme 16 performs much better than Scheme 17. When the Eastbound volume ranges from 172 to 686 veh/h, Scheme 16 performs similarly to Scheme 17. When the Eastbound volume is 1029 veh/h, Scheme 17 shows a great advantage relative to Scheme 16.
Although Figure 12 indicates the better performance of Schemes 16 and 17, for real traffic management, only one scheme can be used in practice. Both Schemes 16 and 17 are good, but the difference between the two schemes still needs to be calculated. The ratio of improvement from Scheme 17 to Scheme 16 is calculated as Ratio = (Scheme 17 − Scheme 16)/Scheme 16 * 100%. The result is shown in Figure 13:   Figure 13 shows the difference between Schemes 16 and 17. For travel time, the two schemes have 22% error at most. For delay, the two schemes have 44% at most, whereas the difference for the number of stops is 236%. The errors between the two schemes are pronounced, and this means that different volumes require different corresponding schemes. The result in Figure 13 supports the validity of the result in Figure 12. Scheme 17 occupies more blocks than Scheme 16 in Figure 12. In Figure 13, with evening peak-hour data, Scheme 17 also performs better than Scheme 16 when the volumes are the same.
For safety performance, the result of Table 3, the safety evaluation showed the great improvement of Schemes 16 and 17 to Scheme 1. Schemes 16 and 17 drastically reduced or eliminated instances of crossing from 362 to 1 and 0. Rear ends were reduced from 609 to 207 and 169, with 66% and 78% improvement, respectively. The lane changes were reduced from 102 to 62 and 64, which is also a significant improvement. Scheme 17 performed better on all three indexes compared to Scheme 16 and 1, which also indicates that Scheme 17 is better than Scheme 16 and 1. Above all, Scheme 17 is a better improvement scheme for this non-aligned intersection caused by a work zone.

Conclusions
Sustainable urban transportation is one of many major issues in urban development in the world today. The impact of work zones throughout the city on sustainable traffic flow is enormous. China is still in a rapid urban construction period, with a rapid increase in private vehicles and the urban population. The traffic system is fragile, but construction is inevitable. Road reconstruction, urban pipeline construction, and subway construction are distributed throughout Chinese cities. At first, a work zone could take up as much land as needed, but soon, people found that an extensive work zone area had a serious impact on traffic operation. Therefore, the occupation area of work zones in cities was reduced as much as possible in recent years in an attempt to reduce the impact on traffic. However, construction periods can last from several months to several years. In some cases, the work zone area is still very large, such as subway work zones. Trying to reduce the work zone area and road encroachment without a specific study on the affected traffic cannot eliminate these very serious traffic problems.
The intersection studied in this article has been shown in Figure 3. The roads on both sides of the intersection are only four lanes wide, while the intersection is as wide as 11 lanes. The wider the road, the larger the traffic capacity, and ignoring the traffic bottleneck caused by merging in a short segment is not appropriate. Sustainable traffic flow will be interrupted in the bottleneck section.
This paper proposes two traffic improvement measures for urban intersections occupied by work zones. Both measures are based on the same core content, namely, the channelization of sustainable traffic flow. The chaos of vehicles when passing through the intersections stems from the fact that there are no lane lines in the intersection area, and there is no horizontal restriction of traffic flow either. A large number of merge movements causes congestion, delay, and stops after passing through the intersection, and it increases accident risks and safety hazards. By adding railing to limit the width of traffic flow and maintaining the same width of the road on both sides of the intersection, traffic problems can be greatly reduced, while also providing a larger area for the work zone.
Of the two improvements proposed in this paper, one (Scheme 16) is the addition of railing to limit the width of traffic flow in the present situation, while the other one (Scheme 17) is a better situation from the perspective of a feasible work zone layout. The traffic flow remains straight when passing through the intersection area as though passing through a normal intersection. After passing through the intersection, the direction changes as the road turns.
The other schemes in Table 3 were used to explore whether the road offset value had a significant relationship with traffic operation under the control of the width of traffic flow. The results show that the relationship is not strong. Furthermore, in practice, the offset of road misalignment is not actively chosen by people, but is determined by the limitations of the work zone. Only Schemes 16 and 17 are feasible and have minimal impact on the work zone layout.
In this research, we proposed two schemes, two ways of channelization, to reduce the unsustainable traffic caused by work zone at intersections. Real traffic data were collected and input into VISSIM to simulate and evaluate the different schemes. Through the research, no obvious relationship was found to exist with offset values at the non-aligned intersection. The travel time, delay, and number of stops were the three indexes of evaluation. The entropy method was used to calculate the weight of three indexes, which determined the schemes selection matrix in the end. The selection matrix can be used for scheme selection for different combinations. Scheme 17 performed the best according to the traffic volumes collected.
The research in this paper can be applied to evaluate the impact of a work zone on urban sustainable traffic flow. Using two corresponding improvement schemes can greatly alleviate congestion, reduce travel time, delay, and the number of stops. The core of the improvement is the channelized management of sustainable traffic flow. For the roads occupied by the work area, the results of this study can greatly reduce the impact on traffic. Compared with a state without any control measures, the travel time can be reduced by up to 44%, delays can be reduced by up to 66%, and parking times can be reduced by up to 92%. There are still some topics in this article that can be studied further-the first is how to improve the traffic operation situation caused by the working area at the intersection, while the second is the impact of the advanced parking line in Scheme 17 on traffic operations.