Hybrid Systems Optimization: Application to Hybrid Systems Photovoltaic Connected to Grid. A Mali Case Study

: Access to electricity and supplying reliable energy are the key elements that support local economic development and contribute to reducing poverty. Moreover, the problem of environmental protection can be considered as a factor of sustainable development. In response to these many challenges, appropriate national and regional policies, as well as mechanisms, have been implemented. In Mali, strong dependence on the importation of oil, growth in demand, and the low rate of electriﬁcation have pushed the highest authorities to think of diversiﬁed technological solutions like renewable energy for the satisfaction of energy demands, especially photovoltaics, for which the country has signiﬁcant potential. The hybrid systems used is a compromise, because the emission rate of carbon dioxide emitted by thermal power plants must be reduced and limited to preserve supernatural disasters. For this, hybrid photovoltaic systems coupled to the grid increased, but the management of the production of these photovoltaics poses a lot of problem due to its intermittent status. It is in this context that we conducted an optimization study of a hybrid system photovoltaic connected to the grid. We applied our approach to the most extensive distribution post of Mali capital. For the simulation, we used the modeling and simulation tool named HOMER.


General Introduction
The intense energy demand, as well as the instant consumptions, believe very quickly according to the seasons (winter and summer), the depletion and impact of fossil fuel deposits are becoming threatening [1]. However, the production of energy in quantity and quality is a challenge of great importance. Dependence on fossil fuels as a primary energy source will lead to the depletion of fuels, environmental pollution, and negative impacts on human health [1]. Figure 1 illustrates the evolution of fuel consumed for power generation from 2000 to 2014 [2]. Today, faced with the adverse consequences of climate change, it is essential to maintain the global temperature below 2 • C, a maximum increase of only 1.5 • C [3]. For it, the implementation of photovoltaic-grid hybrid power plants for the production of electricity will reduce the level of CO 2 emissions, and contribute to increasing revenues [4]. To achieve these objectives and mitigate global warming, the use of renewable energies, which is an abundant resource accessible to all, is a sustainable solution. Therefore, many countries have begun to include solar energy programs in their planning to support sustainable development and environmental The investment costs of photovoltaic (PV) technology are now near the lowest cost level, and the additional reduction can be achieved by discovering new raw products or by developing a cheaper materials manufacturing technology [14]. The leveled cost of electricity (LCOE) of PV panels with an installation size of 1 kW to 6 kW, under Italian conditions, was between 0.10 and 0.11/kWh, which is considered competitive with other green electricity technologies [15]. The amount of electricity produced by the PV modules depends mainly on the composition, type of the module, the combined effect of the installation, and the dominant natural factors [16]. Concerning the energy efficiency ratio of the photovoltaic technology, single-crystalline Si and multi-crystalline Si systems can provide a >90% net-to-gross energy return ratio, even when deployed in non-optimal locations, according to Leccisi et al. [17]. However, because of the photovoltaic module heating, its energy production decreases, affecting the total energy production of the PV system [18,19].
Based on the global distribution map of annual solar radiation, the average yearly amount of PV energy that can be generated is between 640-2400 kWh/m 2 depending on the different geographical areas. In Mali, this is between 2100 to 2300 kWh/m 2 (see Figure 2) [20]. In view of this, the potential of solar energy available to Mali, and the constant increase in the operating cost of thermal power stations, in 2006, the government of Mali adopted the renewable energy development strategy, whose primary objective is to sustainably increase the contribution of renewable energies in the overall energy balance of the country, from less than 1% in 2002 to 15% in 2020 [21]. The interconnected grid of EDM-SA (or Mali's national electricity grid) has various production plants, basically divided between three technologies of the source of electrical energy: Thermal, hydroelectric (including purchases of hydroelectricity, and excluding other renewables), and regional interconnection power grids (Ivory Coast) [21]. In 2013, the total installed capacity of the national grid was 424.26 MW, of The investment costs of photovoltaic (PV) technology are now near the lowest cost level, and the additional reduction can be achieved by discovering new raw products or by developing a cheaper materials manufacturing technology [14]. The leveled cost of electricity (LCOE) of PV panels with an installation size of 1 kW to 6 kW, under Italian conditions, was between 0.10 and 0.11/kWh, which is considered competitive with other green electricity technologies [15]. The amount of electricity produced by the PV modules depends mainly on the composition, type of the module, the combined effect of the installation, and the dominant natural factors [16]. Concerning the energy efficiency ratio of the photovoltaic technology, single-crystalline Si and multi-crystalline Si systems can provide a >90% net-to-gross energy return ratio, even when deployed in non-optimal locations, according to Leccisi et al. [17]. However, because of the photovoltaic module heating, its energy production decreases, affecting the total energy production of the PV system [18,19].
Based on the global distribution map of annual solar radiation, the average yearly amount of PV energy that can be generated is between 640-2400 kWh/m 2 depending on the different geographical areas. In Mali, this is between 2100 to 2300 kWh/m 2 (see Figure 2) [20]. In view of this, the potential of solar energy available to Mali, and the constant increase in the operating cost of thermal power stations, in 2006, the government of Mali adopted the renewable energy development strategy, whose primary objective is to sustainably increase the contribution of renewable energies in the overall energy balance of the country, from less than 1% in 2002 to 15% in 2020 [21]. The interconnected grid of EDM-SA (or Mali's national electricity grid) has various production plants, basically divided between three technologies of the source of electrical energy: Thermal, hydroelectric (including purchases of hydroelectricity, and excluding other renewables), and regional interconnection power grids (Ivory Coast) [21]. In 2013, the total installed capacity of the national grid was 424.26 MW, of which 39.42% was for the clean structures (hydroelectric and thermal unit) of the EDM-SA and 60.58% was for the purchase of energy (hydroelectric and thermal unit) and regional interconnection (Ivory Coast). Facing these difficulties related to the energy production, the objectives fixed by the government of Mali concerning of renewable energies connected at the grid must pass from 6.3 MW in 2010 to 150. 7   It is in this context that we will address "hybrid systems optimization: Application to hybrid systems photovoltaic connected to grid". The objective is to allow better management of these hybrid systems and optimize the production of thermal energy according to the availability of solar productions.
Several works have been brought on PV solar plants installed in the world. A study on the performance analysis of a solar power plant connected to the 171.36 kW grid on the island of Crete in 2002 was done by Kymakis et al. in 2009 [22]. An evaluation of 13 different photovoltaic technologies in two localities (Nicosia, Cyprus and Stuttgart, Germany), all connected to the grid with a rated power of 1 kW was led by Makrides et al. in 2010 [23]. A study by V. Sharma et al. in 2013 focused on evaluating the performance of different rows of PV technologies consisting of polycrystalline silicon, thin film, and amorphous silicon at the Solar Energy Center in India [24]. The performance of a PV power plant connected to the network using the various methods was studied by Hassan et al. in 2014 [25]. Yang et al., in 2015, analyzed the reliability of a single-phase converter with reactive power injection at night by considering mission profiles [26]. A new approach to reliability was proposed by Huai et al. in 2016 [27]. Frede et al., in 2017, discussed the reliability of renewable energy systems [28]. A design study and selection of reliable converters for photovoltaic applications connected to the grid was carried out by Victor et al. in 2018 [29]. Sangwongwanich et al., in 2018, conducted an approach of the power control flexibility of solar systems [30]. A study on an autonomous photovoltaic system in an urban area of Mexico was led by Alberto et al. in 2018 [31]. Research on the reconfiguration of a multi-state converter was carried out by Chen et al. in 2018 [32].
Most of the studies on hybrid systems photovoltaic connected to the grid have been based on solar power plant performance evaluation, reliability converter, and maximization of installed PV power output. However, renewable sources are intermittent sources, and managing its productions according to their availability remains a significant challenge. This work will be focused on the optimization of thermal energy production, which is an undesirable source according to the availability of solar power generation, and on the other hand, allowing Mali's electricity supplier (EDM-SA Energy of Mali) to have a reliable estimate of purchases from interconnection with a neighboring country (Ivory Coast). It is in this context that we will address "hybrid systems optimization: Application to hybrid systems photovoltaic connected to grid". The objective is to allow better management of these hybrid systems and optimize the production of thermal energy according to the availability of solar productions.
Several works have been brought on PV solar plants installed in the world. A study on the performance analysis of a solar power plant connected to the 171.36 kW grid on the island of Crete in 2002 was done by Kymakis et al. in 2009 [22]. An evaluation of 13 different photovoltaic technologies in two localities (Nicosia, Cyprus and Stuttgart, Germany), all connected to the grid with a rated power of 1 kW was led by Makrides et al. in 2010 [23]. A study by V. Sharma et al. in 2013 focused on evaluating the performance of different rows of PV technologies consisting of polycrystalline silicon, thin film, and amorphous silicon at the Solar Energy Center in India [24]. The performance of a PV power plant connected to the network using the various methods was studied by Hassan et al. in 2014 [25]. Yang et al., in 2015, analyzed the reliability of a single-phase converter with reactive power injection at night by considering mission profiles [26]. A new approach to reliability was proposed by Huai et al. in 2016 [27]. Frede et al., in 2017, discussed the reliability of renewable energy systems [28]. A design study and selection of reliable converters for photovoltaic applications connected to the grid was carried out by Victor et al. in 2018 [29]. Sangwongwanich et al., in 2018, conducted an approach of the power control flexibility of solar systems [30]. A study on an autonomous photovoltaic system in an urban area of Mexico was led by Alberto et al. in 2018 [31]. Research on the reconfiguration of a multi-state converter was carried out by Chen et al. in 2018 [32].
Most of the studies on hybrid systems photovoltaic connected to the grid have been based on solar power plant performance evaluation, reliability converter, and maximization of installed PV power output. However, renewable sources are intermittent sources, and managing its productions according to their availability remains a significant challenge. This work will be focused on the optimization of thermal energy production, which is an undesirable source according to the availability of solar power generation, and on the other hand, allowing Mali's electricity supplier (EDM-SA Energy of Mali) to have a reliable estimate of purchases from interconnection with a neighboring country (Ivory Coast).

Characteristics of PV System
Among the many environmental factors that affect the operating characteristics of a photovoltaic cell and its energy production, the solar irradiation G measured in W/m 2 and the temperature T measured in degrees Celsius ( • C) are the two main factors [33].
The source of photocurrent Iph is expressed as follows in the following equation [34]; it depends on both irradiance and temperature.
where I scn is the rated short-circuit current, K i is the current temperature coefficient, G n is the rated solar radiation, which is distinctively 1000 W/m 2 , and T n is the rated cell temperature, which is distinctively The values of G n and T n can be determined from the datasheet of cells or commercial PV panels. Also, the current I d and the voltage V d of the diode are expressed by an exponential relationship and are represented by Equations (2) and (3) [34].
where I s is the saturation diode current, a is the ideality constant of the diode, V d is the voltage of the diode, and V t is the thermal voltage of the semiconductor junction. The saturation current of the diode depends on the temperature and can be defined as: where V ocn is the open-circuit nominal voltage, and K v is the temperature coefficient of the voltage. The diode voltage V d is the same as the PV voltage V PV of an ideal model. The thermal voltage V t depends on temperature T and is established in Equation (4) [34].
where k is the Boltzmann constant (1.3807 × 10 −23 J·K −1 ), q is the electronic charge (1.60217662 × 10 −19 C), and N s is the number of PV cells in series.
The intensity of the current at the output of the PV, I PV , and its power P PV , are given respectively by Equations (5) and (6) [35]: R s , R p are respectively the series and parallel resistors of the PV source. Where the current I ph is defined in Equation (1) and the current of the diode I d in Equation (2).
From the equation of the current I PV given in Equation (5), it can be concluded that the output current of the PV depends on the solar irradiation G and temperature ambient T.
According to the variation of the solar irradiation and the temperature, Equation (5) can be used to determine the current and power characteristic curve of a PV for a given voltage Figure 3 [34].           When irradiation and temperature vary, the I-V curve will also change, as shown in Figure 4. Solar irradiation is directly proportional to current characteristics; if it increases, the short circuit current and the maximum power point (MPP) current also increase. Conversely, the temperature is inversely proportional to the characteristics of the voltage. When the temperature increases, the voltage open circuit (VOC) and the MPP voltage decrease. Therefore, a cell will produce the most power when the intensity of sunlight is high, but when the temperature is low ( Figure 3). However, these types of environmental conditions are not common because the higher-intensity light striking an object tends to increase its heat at the same time.
Variety studies have confirmed these hypotheses. Zsiborács et al. [36] and Chandrasekar et al. [37] have shown that in crystalline solar modules, a 1 • C temperature increase will generally result in a 0.5% reduction efficiency. According to Skoplaki [18], the efficiency the crystalline modules can have a loss of 0.3% to 0.5% when the temperature increases by 1 • C. Krauter [19] establishes that the energy-temperature relationship varies between 0.4% and 0.5%/ • C for the same technology. In the case of unglazed glazing of a photovoltaic, the decrease in electrical efficiency is linear and equal to 0.015 when the temperature was between 25 • C and 34 • C and the solar radiation increased from 100 to 1000 W/m 2 [38]. According, Zsiborács et al. [39], with silicon photovoltaic cells, a decrease of 1 • C in temperature will result in an average increase of 0.27% in efficiency of energy production.
The rest of the paper is structured follows: In Section 2, materials and methods are discussed; in this section, an overview of the solar resources in Mali and how coupled a photovoltaic system to an electricity grid is discussed in Sections 2.1 and 2.2; an application case is processed in Section 2.3. The results and discussions on the best optimization strategy are presented in Section 3, and a conclusion in Section 4.

Solar Resources in Mali
Before addressing the solar energy field in Mali, we recall some scientific concepts related to solar energy.

•
Global horizontal irradiance (GHI): Total amount of direct and diffuse radiation received on a horizontal surface expressed in Wh/m 2 . • Diffuse horizontal irradiance (DHI): Total solar radiation received in one hour on a surface directly exposed to solar radiation, in Wh/m 2 . • Global irradiation (G): Total solar radiation received in one hour from the sky, after deduction of direct radiation, expressed in Wh/m 2 .
Solar data in Mali are available through many sources. Here, we used the data climate variation conditions of Bamako ( Figure 6), obtained on the Meteonorm© site.
In the graphs above, representing the solar radiation, the temperature, and the duration of insolation on the site of Bamako, we considered the average monthly data from Meteonorm©.

•
Diffuse horizontal irradiance (DHI): Total solar radiation received in one hour on a surface directly exposed to solar radiation, in Wh/m 2 . • Global irradiation (G): Total solar radiation received in one hour from the sky, after deduction of direct radiation, expressed in Wh/m 2 .
Solar data in Mali are available through many sources. Here, we used the data climate variation conditions of Bamako ( Figure 6), obtained on the Meteonorm© site.

PV Systems Connected to a Grid
Satisfying energy needs, peri-urban, rural, and even urban areas have proved difficult in different conditions such as: • The electricity grid does not cover all the energy needs permanently (permanent load shedding).

•
The cost of electricity is high.

•
The reduction of the pollution rate due to the misuse of thermal energies, which becomes a daily threat (preservation of the environment). • Independence in electricity.
In Mali, we found a very high solar potential of 6 KWh/m 2 /day (February to May, see Figure 7) with a daily average sunshine duration between 7 to 9 h of sunshine ( Figure 8) and an annual average solar energy, indicated on the map above, of 2190 KWh/m 2 /year [20].
Thus, hybridization of the existing sources of energy with photovoltaic sources in Mali may be a possible solution to meet the requirements mentioned above. The production of photovoltaic power (PV) connected to the electricity grid has increased considerably in recent times due to climate change conditions and the high demand for energy consumption. In the graphs above, representing the solar radiation, the temperature, and the duration of insolation on the site of Bamako, we considered the average monthly data from Meteonorm©.

PV Systems Connected to a Grid
Satisfying energy needs, peri-urban, rural, and even urban areas have proved difficult in different conditions such as: • The electricity grid does not cover all the energy needs permanently (permanent load shedding).

•
The cost of electricity is high.

•
The reduction of the pollution rate due to the misuse of thermal energies, which becomes a daily threat (preservation of the environment). • Independence in electricity.
In Mali, we found a very high solar potential of 6 ℎ/ / (February to May, see Figure  7) with a daily average sunshine duration between 7 to 9 h of sunshine ( Figure 8) and an annual average solar energy, indicated on the map above, of 2190   Thus, hybridization of the existing sources of energy with photovoltaic sources in Mali may be a possible solution to meet the requirements mentioned above. The production of photovoltaic power A basic structure of a photovoltaic production system connected to the electricity grid is presented in Figure 9 [34]. It includes photovoltaic modules, a power converter, a control unit, and the grid. (PV) connected to the electricity grid has increased considerably in recent times due to climate change conditions and the high demand for energy consumption.
A basic structure of a photovoltaic production system connected to the electricity grid is presented in Figure 9 [34]. It includes photovoltaic modules, a power converter, a control unit, and the grid. The PV source is connected to a DC/DC and/or DC/AC power converter, which connects the PV generated power to the grid or operates in an autonomous mode (for example, a group of batteries) [40,41].
Photovoltaic systems connected to the grid multiply and can play a significant role in power generation [42,43]. Although the capacity of a photovoltaic system is still lower than that of a wind system, energy demands for PV systems are becoming increasingly important [44] for the fact that the number of photovoltaic systems with high power continually increases [45]. In contrast, the production of a photovoltaic system is strongly dependent on the different variations of the atmospheric conditions (solar irradiation and ambient temperature).
Therefore, it is necessary to maximize the output power of the PVs by a DC/DC converter controlled by a control unit known as the maximum power point tracking (MPPT). For this, the DC voltage at the output of the DC/DC converter must be maintained at a value acceptable by the inverter. Besides, PV supervision, diagnosis, and maintenance must be checked periodically for safety reasons (for example, fires) [46]. At the power grid for good power quality, the desirable total harmonic distortion (THD) of the output current must be achieved [47]. In the case of photovoltaic systems coupled to a high-voltage grid, photovoltaic systems must respect the voltage and the frequency of the grid, provide ancillary services (frequency regulation for example), and overcome grid failures (such as voltage drops and frequency variations) when a higher level of penetration becomes a reality [48].

Case Study Approach
We applied our approach to the energy distribution post of BALINGUE, which is the most extensive energy distribution post in Bamako (Mali's capital city). The distribution post is supplied with energy produced by a thermal power station at BALINGUE itself; the energy production purchased on the interconnection network with a neighboring country (Ivory Coast), SELINGUE and SOTUBA hydro-electric production, are sources of energy specific to EDM. It supports seven urban The PV source is connected to a DC/DC and/or DC/AC power converter, which connects the PV generated power to the grid or operates in an autonomous mode (for example, a group of batteries) [40,41].
Photovoltaic systems connected to the grid multiply and can play a significant role in power generation [42,43]. Although the capacity of a photovoltaic system is still lower than that of a wind system, energy demands for PV systems are becoming increasingly important [44] for the fact that the number of photovoltaic systems with high power continually increases [45]. In contrast, the production of a photovoltaic system is strongly dependent on the different variations of the atmospheric conditions (solar irradiation and ambient temperature).
Therefore, it is necessary to maximize the output power of the PVs by a DC/DC converter controlled by a control unit known as the maximum power point tracking (MPPT). For this, the DC voltage at the output of the DC/DC converter must be maintained at a value acceptable by the inverter. Besides, PV supervision, diagnosis, and maintenance must be checked periodically for safety reasons (for example, fires) [46]. At the power grid for good power quality, the desirable total harmonic distortion (THD) of the output current must be achieved [47]. In the case of photovoltaic systems coupled to a high-voltage grid, photovoltaic systems must respect the voltage and the frequency of the grid, provide ancillary services (frequency regulation for example), and overcome grid failures (such as voltage drops and frequency variations) when a higher level of penetration becomes a reality [48].

Case Study Approach
We applied our approach to the energy distribution post of BALINGUE, which is the most extensive energy distribution post in Bamako (Mali's capital city). The distribution post is supplied with energy produced by a thermal power station at BALINGUE itself; the energy production purchased on the interconnection network with a neighboring country (Ivory Coast), SELINGUE and SOTUBA hydro-electric production, are sources of energy specific to EDM. It supports seven urban departures (DU) of 15 KV and two departures of 30 KV, which supplies the city of KOULIKORO and the energy distribution post of BALKOU. Distribution post of BALKOU also has five urban departures (DU) of Bamako in 15 KV (Figure 10). Our objective is to minimize the purchase of energy and the production of thermal energy with the connection of a 30 MW solar plant. For the work, we used the one-year database obtained at the distribution post level. Table 1 includes monthly and annual productions. In this table, there is no production of the solar plant because it is not connected to the station at the moment.
The following figures (Figure 11 and 12) represent the monthly and yearly productions of the different production points and the load that we did using the Excel tool. For the work, we used the one-year database obtained at the distribution post level. Table 1 includes monthly and annual productions. In this table, there is no production of the solar plant because it is not connected to the station at the moment.
The following figures (Figures 11 and 12) represent the monthly and yearly productions of the different production points and the load that we did using the Excel tool.  The objective of the optimization will be to give priority to solar production when it is available and hydroelectric productions specific to EDM, which is SOTUBA and SELINGUE. If these productions are not sufficient to take charge, we proceed to the purchase of the interconnection network with a neighboring country (Ivory Coast), but with the idea of not exceeding a given threshold. We use the thermal power station, which is costly and fatal for climate change if there is no solution.
For the simulation, we modeled our system with the annual data collected by the agents of the distribution station by using the modeling and simulation tool HOMER. As the SOTUBA and SELINGUE hydroelectric power stations are clean sources of EDM, they were seen as permanent, according to the data that we have. The purchase on the interconnection grid and the operation of the thermal power station are automatic in case the two hydroelectric power stations and the production of the solar power station do not satisfy the energy demand.  The objective of the optimization will be to give priority to solar production when it is available and hydroelectric productions specific to EDM, which is SOTUBA and SELINGUE. If these productions are not sufficient to take charge, we proceed to the purchase of the interconnection network with a neighboring country (Ivory Coast), but with the idea of not exceeding a given threshold. We use the thermal power station, which is costly and fatal for climate change if there is no solution.
For the simulation, we modeled our system with the annual data collected by the agents of the distribution station by using the modeling and simulation tool HOMER. As the SOTUBA and SELINGUE hydroelectric power stations are clean sources of EDM, they were seen as permanent, according to the data that we have. The purchase on the interconnection grid and the operation of the thermal power station are automatic in case the two hydroelectric power stations and the production of the solar power station do not satisfy the energy demand. The objective of the optimization will be to give priority to solar production when it is available and hydroelectric productions specific to EDM, which is SOTUBA and SELINGUE. If these productions are not sufficient to take charge, we proceed to the purchase of the interconnection network with a neighboring country (Ivory Coast), but with the idea of not exceeding a given threshold. We use the thermal power station, which is costly and fatal for climate change if there is no solution.
For the simulation, we modeled our system with the annual data collected by the agents of the distribution station by using the modeling and simulation tool HOMER. As the SOTUBA and SELINGUE hydroelectric power stations are clean sources of EDM, they were seen as permanent, according to the data that we have. The purchase on the interconnection grid and the operation of the thermal power station are automatic in case the two hydroelectric power stations and the production of the solar power station do not satisfy the energy demand.
For optimization, we considered two cases. In the first case, we set the purchase of energy at a maximum of 50 MW to see the impact of the use of the solar power station on the purchase of energy. In the second case, we increased the purchase of energy at a maximum of 100 MW to see the impact on thermal production. Then, we compared the two cases to estimate the cost of production and contribution to the pollution of the thermal power station. These values were chosen after analysis of the database whose peak power purchase was 96.90 MW in March.

For 50 MW Purchase Decision
The tables below summarize the simulation results when we decide not to exceed the purchase of energy with the neighboring country of 50 MW.
Looking at Tables 1 and 2, we can see that the yearly energy purchase decreased sharply from 306,030.513 MWh to 153,778 MWh. However, the production of the thermal power station saw a small increase from 178,777,965 MWh to 211,537 MWh. Besides, when we look at Table 3, we find that the company managed to sell a little energy in case of overproduction of the solar plant that was even more important in January. The increase in thermal production can be compensated by this overproduction sold, but the climate impact is still adverse in this condition.

For 100 MW Purchase Decision
The results of the optimization of when it is decided to increase the purchase to a maximum of 100 MW have been summarized in the tables below.
In Tables 1 and 4, we note that the purchase of energy increased with a difference of 71,568.49 MWh, but in reference to Table 5, this difference was reduced to 57,865.49 MWh, which is insignificant. However, the production of the thermal power station decreased considerably from 178,777.965 MWh to 20,240 MWh. Given this sharp fall, the 57,695.49 MWh surplus purchases are insignificant compared to the inconvenience of thermal production on climatic conditions.

Comparisons
In both cases, we saw the importance of solar production on both productions. In this section, we highlighted economic and ecological impacts, which are a current preoccupation for all nations, and especially Mali, which is a developing country.
The following tables summarize the statistics of the thermal power plant and its emission effects for both cases.
When we look at Tables 6 and 7, we notice that for the decision to buy up to 50 MW on the interconnection network of the neighboring country, almost all the data were multiplied by 10. This is very important from the economic and climate change point of view. The number of startup groups increased from 168 to 338, which played significantly over its lifetime and reduced it considerably. Given these tables, it is evident that the optimal solution for this distribution station is the second case, which is the decision to purchase a maximum of 100 MW. Figure 13 represents a comparison between the data of the database, the decision of a maximum purchase of 50 MW, and a maximum purchase of 100 MW. In Figure 14, we have fuel consumption for simulation cases. We can notice the net difference in these figures and conclude that the decision to buy a maximum of 100 MW is the best solution in economic and ecological terms.  In both cases, we saw the importance of solar production on both productions. In this section, we highlighted economic and ecological impacts, which are a current preoccupation for all nations, and especially Mali, which is a developing country.
The following tables summarize the statistics of the thermal power plant and its emission effects for both cases.
When we look at Tables 6 and 7, we notice that for the decision to buy up to 50 MW on the interconnection network of the neighboring country, almost all the data were multiplied by 10. This is very important from the economic and climate change point of view. The number of startup groups increased from 168 to 338, which played significantly over its lifetime and reduced it considerably. Given these tables, it is evident that the optimal solution for this distribution station is the second case, which is the decision to purchase a maximum of 100 MW. Figure 13 represents a comparison between the data of the database, the decision of a maximum purchase of 50 MW, and a maximum purchase of 100 MW. In Figure 14, we have fuel consumption for simulation cases. We can notice the net difference in these figures and conclude that the decision to buy a maximum of 100 MW is the best solution in economic and ecological terms.  The figures below represent time-series representations of the total load and the different productions for the case where it is decided to buy a maximum of 100 MW.
This curve allows us to see the evolution of consumption in terms of energy and the state of the different productions. Here, we randomly selected between 1 and 14 January to see its condition. At this time, even the solar power station alone can take charge, but the values of SOTUBA and SELINGUE are available because they were considered permanent for the simulation.
In Figure 15, we can see that consumption was high from 2 March and started to reduce from July; a further increase is observable in October and November. The month of January was observed as the lowest consumption month. It can also be noted that the thermal power plant was used a lot between April and July, as well as October when the energy demand was high. The figures below represent time-series representations of the total load and the different productions for the case where it is decided to buy a maximum of 100 MW.
This curve allows us to see the evolution of consumption in terms of energy and the state of the different productions. Here, we randomly selected between 1 and 14 January to see its condition. At this time, even the solar power station alone can take charge, but the values of SOTUBA and SELINGUE are available because they were considered permanent for the simulation.
In Figure 15, we can see that consumption was high from 2 March and started to reduce from July; a further increase is observable in October and November. The month of January was observed as the lowest consumption month. It can also be noted that the thermal power plant was used a lot between April and July, as well as October when the energy demand was high.
From this curve, you can zoom to see a representation, on a quarter, a week, or a day. By enlarging the curve (Figure 16), we see that the thermal power station was not used every day of June, which we can conclude by examining the representation on the year. this time, even the solar power station alone can take charge, but the values of SOTUBA and SELINGUE are available because they were considered permanent for the simulation.
In Figure 15, we can see that consumption was high from 2 March and started to reduce from July; a further increase is observable in October and November. The month of January was observed as the lowest consumption month. It can also be noted that the thermal power plant was used a lot between April and July, as well as October when the energy demand was high. From this curve, you can zoom to see a representation, on a quarter, a week, or a day. By enlarging the curve (Figure 16), we see that the thermal power station was not used every day of June, which we can conclude by examining the representation on the year. as the lowest consumption month. It can also be noted that the thermal power plant was used a lot between April and July, as well as October when the energy demand was high. From this curve, you can zoom to see a representation, on a quarter, a week, or a day. By enlarging the curve (Figure 16), we see that the thermal power station was not used every day of June, which we can conclude by examining the representation on the year. On the weekly curve ( Figure 17), we can distinguish the different productions to satisfy the demand. In the first week of January, despite sometimes unstable solar production, energy was only paid a few hours, and the thermal power station was not used. However, in the third week of May, the thermal power plant was used almost every day for a few hours when the solar power station was not available or unstable. On the weekly curve (Figure 17), we can distinguish the different productions to satisfy the demand. In the first week of January, despite sometimes unstable solar production, energy was only paid a few hours, and the thermal power station was not used. However, in the third week of May, the thermal power plant was used almost every day for a few hours when the solar power station was not available or unstable. On the weekly curve (Figure 17), we can distinguish the different productions to satisfy the demand. In the first week of January, despite sometimes unstable solar production, energy was only paid a few hours, and the thermal power station was not used. However, in the third week of May, the thermal power plant was used almost every day for a few hours when the solar power station was not available or unstable. On the daily representation (Figure 18), we can see the different productions and consumption over 24 h. On 1 January, we observe that from 1 h until 7 h, the energy demand is lower than the SELINGUE production. Around 7 h30, it exceeded the SELINGUE production, and at that moment, the solar power plant production had already started. Despite the instability of the solar plant, the need to purchase was expressed only to 17 h, where the load has risen, and the solar power station was not available. The purchase lasted only from 17 h to 23 h and had an order inferior to 15 MW. The month of January almost functioned in this way, as it was the month where the energy sold was higher than the energy bought. On the daily representation (Figure 18), we can see the different productions and consumption over 24 h. On 1 January, we observe that from 1 h until 7 h, the energy demand is lower than the SELINGUE production. Around 7.5 h, it exceeded the SELINGUE production, and at that moment, the solar power plant production had already started. Despite the instability of the solar plant, the need to purchase was expressed only to 17 h, where the load has risen, and the solar power station was not available. The purchase lasted only from 17 h to 23 h and had an order inferior to 15 MW. The month of January almost functioned in this way, as it was the month where the energy sold was higher than the energy bought.
The day of 21 April was the day when demand was significant. All productions were used that day. At 10 h, despite the availability of the solar power station and the other three, the thermal power plant was used from 10 h to 16 h and from 17 h to 2 h.
It was also observed a short time of availability of the solar plant on 3 August. Practically, it was available only from 8 h to 14 h. The purchase of energy was increased from 14 h to 22 h, but without resorting to the thermal power station. The day of 21 April was the day when demand was significant. All productions were used that day. At 10 h, despite the availability of the solar power station and the other three, the thermal power plant was used from 10 h to 16 h and from 17 h to 2 h.
It was also observed a short time of availability of the solar plant on 3 August. Practically, it was available only from 8 h to 14 h. The purchase of energy was increased from 14 h to 22 h, but without resorting to the thermal power station.

Conclusions
In Mali, energy production is based on production specific to EDM (thermal and hydro-electric) and the purchase of energy from private suppliers including the interconnection network (Ivory Coast). Among these particular production sources, the hydroelectric production is of the order of 35.8 MW (SOTUBA and SELINGUE) ( Table 4), which is insignificant for demand energy that can reach up to 138.43 MW Figure 19. Therefore, thermal power plants will be the primary sources of electricity, and as a result, pollutant factors will increase (Table 5). In this work, we have shown the importance of the use of a PV solar power plant connected to the electricity grid, economically and ecologically. In different cases, we have seen the net contribution of solar production according to its availability.  Figure 19. The model of the system under the simulation tool HOMER.  If we decide to limit the purchase to a maximum of 50 MW, the energy purchased will decrease from 306,030.51 MWh/year to 153,778 MWh/year. However, the thermal production is a significant 211,537 MWh/year (Tables 1 and 2). The energy bought decreases, but this solution is undesirable for the conditions of climatic variation.
By increasing the purchase to a maximum of 100 MW, the energy purchased increased a little from 306,030.51 MWh/year to 323,896 MWh/year, a difference of 17,865.49 MWh/year and 48.95 If we decide to limit the purchase to a maximum of 50 MW, the energy purchased will decrease from 306,030.51 MWh/year to 153,778 MWh/year. However, the thermal production is a significant 211,537 MWh/year (Tables 1 and 2). The energy bought decreases, but this solution is undesirable for the conditions of climatic variation.
By increasing the purchase to a maximum of 100 MW, the energy purchased increased a little from 306,030.51 MWh/year to 323,896 MWh/year, a difference of 17,865.49 MWh/year and 48.95 MWh/day, which is practically negligible (Tables 1 and 4). However, the thermal production was reduced to 20,240 MWh/year (Table 4) and the total fuel consumed decreased from 74,303 L to 7141 L ( Table 6).
Tables 6 and 7 clearly show the impact of thermal energy generation in terms of production cost and contribution to climate change, which are two factors that preoccupy all nations today. In these tables, we note that the lifetime of the thermal power plant decreased from 29.6 years to 2.87 years, a difference of more than 25 years. Its consumption has also been multiplied by more than 10, which increases the cost of production tremendously.
The optimal solution is probably the decision to pay a maximum of 100 MW on the interconnection network of the neighboring country (Figures 14 and 15). It was also observed throughout the year that one overproduction was sold back.
Based on the results of the different simulations, we can say that the objectives of this work have been achieved and help the Mali interconnection network by PV systems to better attain the stabilization objectives of the electricity grid and maintain continuity of service to satisfy consumer demand. It will significantly reduce the energy production of thermal power plants, which contributes positively to climate change, which is today a crucial issue for all of humanity.
But it leaves us many perspectives. Despite the lower production of the thermal power plant, CO 2 emission other polluting factors are still important, at 232,055 kg/year (Table 7). Thus, in the future, we will see if it will cost less to use a storage system that will store overproduction and reuse, instead of thermal production. One can also see if a second solar power plant can be beneficial, considering that the lifetime of the thermal power plant will drop by more than 25 years, which corresponds to the minimum life of a solar system. Further, another alternative, renewable, and non-polluting source such as wind energy or biomass could be investigated.