Global Optimality under Internet of Vehicles: Strategy to Improve Tra ﬃ c Safety and Reduce Energy Dissipation

: Internet of Vehicles (IoV), which enables information exchange among vehicles, infrastructures and environment, is considered to have great potential for improving tra ﬃ c. However, information delays may lead to driver’s incorrect operations and have a negative impact on tra ﬃ c ﬂow. To improve tra ﬃ c safety and reduce energy dissipation under IoV conditions, this paper intends to explore a more favorable driving strategy, which may weaken the adverse e ﬀ ects of information delays. This study regarding driving strategy is based on an improved car-following model with consideration of Global Optimality (GO-FVD model). Linear stability analysis and numerical simulations are carried out to explore the e ﬀ ects of Global Optimality on tra ﬃ c ﬂow. Results conﬁrm that Global Optimality contributes to enhancing the stability and safety of tra ﬃ c ﬂow as well as depressing the energy dissipation. In particular, it is more suitable for the low-density tra ﬃ c to account for Global Optimality. These results can provide theoretical support for the development of favorable driving strategy under IoV conditions, which will promote the sustainable development of intelligent transportation.


Introduction
Traffic problems such as traffic accidents, congestion, and energy consumption have aroused wide concern in modern society [1][2][3][4][5][6][7]. Intelligent Transportation System (ITS) is considered to have great potential for solving these problems [8][9][10][11][12][13][14]. As an integral component of future ITS, Internet of Vehicles (IoV) enables the information exchange among vehicles, infrastructures and environment [15][16][17]. Accordingly, drivers will be provided with more traffic information, which supports their driving tasks. For instance, the driving states of vehicles in the vicinity can be obtained, according to which drivers adjust their own driving states. However, the states of vehicles are constantly changing, and transfer delays of information are common [18,19]. As a result, drivers may receive untimely information, leading to their incorrect operations which have negative influences on traffic. How to weaken the adverse effects of transfer delays and improve traffic under IoV conditions? Besides the advances in information transmission technology, the improvement of driving strategy is of great importance as well. However, the question has not been extensively investigated from the perspective of driving strategy.
To this end, the purpose of this paper is to explore a driving strategy that is able to improve traffic safety and reduce energy dissipation under IoV conditions. Specifically, the strategy with consideration of Global Optimality is the main focus of this study. Here, Global Optimality means that the average headway of traffic flow on a road with a certain length is taken into account when drivers adjust their driving states. This is because the average headway reflects the overall traffic situation on a road segment [20]. Furthermore, it is relatively stable information and little influenced by transfer delays. Consequently, this paper proposes the hypothesis that the traffic will be improved by considering Global Optimality under IoV conditions.
In addition, microscopic traffic models are not only important approaches to study traffic problems but also beneficial evaluation tools for ITS [21]. Particularly, car-following models can effectively describe interactions of vehicles and capture complex characteristics of vehicle dynamics in real traffic [22]. Traffic problems in ITS environment have been widely studied using car-following models as shown in the literature review part. Nonetheless, most of these models just considered the effects of vehicles in the vicinity on drivers, but the Global Optimality was neglected. Thus, there is a need for an improved car-following model to explore the effects of Global Optimality on traffic under IoV conditions. Therefore, to investigate the hypothesis proposed above, this paper formulates an improved car-following model with consideration of Global Optimality (GO-FVD model). Based on GO-FVD model, the effects of Global Optimality on traffic stability, safety as well as energy dissipation are tested by analytical and numerical methods. The new model will provide theoretical reference for further study with respect to traffic problems in IoV environment. The findings in this study may help to improve the traffic under IoV conditions, which will promote the sustainable development of intelligent transportation.
The structure of this paper is as follows. Section 1 is the introduction. Section 2 displays some related literatures. The methods used in this paper are introduced in Section 3. Section 4 presents the results and discussion. The conclusions are given in Section 5.
Newell model [26] holds that each vehicle has its optimal velocity. Assuming the position of vehicle n at time t is x n (t), then the optimal velocity of vehicle n at time t can be represented by V(∆x n (t)), which depends on the headway ∆x n (t) between vehicle n and the preceding vehicle n + 1, and ∆x n (t) = x n+1 (t) − x n (t). The velocity of vehicle n will be adjusted to its optimal velocity V(∆x n (t)) within a time lag τ. This time lag is caused by driver's reaction delay and vehicle's response delay. Mathematically, Newell model can be defined as: where v n (t + τ) is the velocity of vehicle n at time t + τ. The unrealistically high acceleration was observed in Newell model when the traffic light changes from red to green. To address this issue, Bando et al. proposed OV model [31], which is described as: where α is drivers' sensitivity that can be regarded as the reciprocal of drivers' reaction time. dv n (t)/dt refers to the acceleration of vehicle n at time t. Since OV model adopts acceleration equation instead of velocity equation to replicate traffic phenomenon, it can describe more properties of the real traffic flow. However, comparison with the field data shows that OV model still produces too high acceleration and unrealistic deceleration. To overcome the shortages, Helbing and Tilch proposed the generalized force (GF) model which took into account the negative velocity difference between the current vehicle and the preceding vehicle [32]. Based on OV model and GF model, Jiang et al. proposed FVD model with consideration of both negative and positive velocity differences [21]. The dynamic equation is formulated as: where ∆v n (t) refers to the velocity difference between vehicle n + 1 and vehicle n, and β is the coefficient parameter. Obviously, traffic dynamics can be better described by FVD model. ID model was proposed by Treiber et al. in 2000 [30]. The main idea of ID model is that drivers expect to maintain a constant distance from the preceding vehicle. However, drivers' reaction time (or sensitivity) is ignored in this model. Thus, ID model may be more suitable for autonomous vehicles.
Recent technology advances have significantly pushed forward the development of ITS. The realistic influences and development prospects of ITS have been studied extensively [8][9][10][11][12][13][14][15][16][35][36][37]. Specifically, the adaptive cruise control (ACC) strategy and the Vehicle to Vehicle (V2V) communication have attracted considerable attention. Great efforts have been devoted to study the effects of these new environments on traffic based on car-following models.
ACC vehicles, based on a control algorithm, automatically adjust the velocity to maintain their proper headway from the vehicle in front. The constant safe time headway is an important quantity in this control algorithm [38]. ID model introduces the parameter denoting the time headway and appears to be a good basis for the ACC system. To this end, ID model was widely extended with consideration of real traffic factors under the condition of ACC system [39][40][41]. In 2007, Kesting et al. differentiated parameter sets of ID model to simulate human and automated (ACC) driving behaviors. They found that a small proportion of ACC vehicles led to a drastic reduction of traffic congestion [39]. In 2010, Kesting et al. further proposed an enhanced ID model to simulate the influences of different ACC strategies on the maximum traffic capacity. Results suggested that 1% more ACC vehicles would increase the capacities by about 0.3% [40]. To simulate various ACC behaviors for a microscopic traffic simulator, Horiguchi and Oguchi proposed car-following models for three ACC types based on the derivation of ID model (IDM+) [41].
Through wireless communication technology, V2V communication enables vehicles to exchange driving information within a given communication range. Traffic characteristics in V2V environment will therefore be changed as well. Accounting for driver's timely reaction under the condition of V2V communication, Hua et al. extended the Newell model. Based on this model, they explored the effects of V2V communication on traffic flow during vehicle starting and braking process as well as in the event of an emergency [42]. Additionally, many studies held that, in light of V2V availability, drivers could respond to vehicles in the vicinity [43][44][45]. Wang et al. argued that considering multiple vehicles in front would enhance the stability of traffic flow. Thus, they proposed the Multiple Velocity Difference (MVD) model by introducing multiple velocity differences into the FVD model [43]. In addition to the velocity difference, another Multiple Car-Following (MCF) model took into account the headways of multiple vehicles in front [44]. Sun et al. formulated a car-following model under V2V communication condition based on OV model and investigated the effects of feedback control signal on traffic flow [45]. Results of these studies were consistent, which indicated that considering information of multiple vehicles in front contributed to suppressing traffic congestion as well as depressing energy consumption.
Notably, it is pointed out that transfer delays of information are common, which has negative effects on traffic [18,19]. However, there are few studies with respect to driving strategies that will weaken these adverse effects. Therefore, it is of great importance to explore such driving strategy. This paper holds that the consideration of Global Optimality appears to be a favorable strategy in IoV environment. In addition, previous studies have verified that car-following models are helpful tools for predicting the effects of ACC systems and V2V communication on traffic. IoV is an integral component of future ITS and the extension of V2V communication. Therefore, this paper will investigate the effects of Global Optimality on traffic based on an improved car-following model under IoV conditions.

Methodology
As described above, FVD model is especially suitable for the study of traffic phenomenon under IoV conditions. Therefore, to explore the effects of Global Optimality on traffic, GO-FVD model is first formulated in this study. Based on GO-FVD model, linear stability analysis is then conducted to deduce the stability condition of traffic flow. Finally, numerical simulations are carried out to investigate the specific effects of Global Optimality on traffic stability, traffic safety and energy consumption.

Model
In the environment of IoV, as mentioned in the introduction part, Global Optimality can be reflected by the average headway that is relatively stable information. Consequently, in addition to considering the preceding vehicle, taking the average headway into account may help suppress driver's incorrect operations. According to this standpoint, this paper, based on FVD model, proposes a car-following model with consideration of Global Optimality (GO-FVD model). The new model can be described as: where L is the global length of a road and N is the global number of vehicles ( Figure 1). V(L/N) denotes the ideal velocity, which is the function of the average headway L/N and refers to the desired velocity for the uniform flow. V(∆x n (t)) is the optimal velocity, which depends on the headway ∆x n (t) of vehicle n and represents the desired velocity of the current vehicle. The Global Optimality can be achieved only when the velocities of all vehicles are equal to the ideal velocity. Parameter λ is the coefficient of velocity difference between the ideal velocity and the current velocity. Parameter γ is the coefficient of velocity difference between the ideal velocity and the optimal velocity. Other variables have the same meanings as that in Equations (1) to (3). This paper holds that the consideration of Global Optimality appears to be a favorable strategy in IoV environment. In addition, previous studies have verified that car-following models are helpful tools for predicting the effects of ACC systems and V2V communication on traffic. IoV is an integral component of future ITS and the extension of V2V communication. Therefore, this paper will investigate the effects of Global Optimality on traffic based on an improved car-following model under IoV conditions.

Methodology
As described above, FVD model is especially suitable for the study of traffic phenomenon under IoV conditions. Therefore, to explore the effects of Global Optimality on traffic, GO-FVD model is first formulated in this study. Based on GO-FVD model, linear stability analysis is then conducted to deduce the stability condition of traffic flow. Finally, numerical simulations are carried out to investigate the specific effects of Global Optimality on traffic stability, traffic safety and energy consumption.

Model
In the environment of IoV, as mentioned in the introduction part, Global Optimality can be reflected by the average headway that is relatively stable information. Consequently, in addition to considering the preceding vehicle, taking the average headway into account may help suppress driver's incorrect operations. According to this standpoint, this paper, based on FVD model, proposes a car-following model with consideration of Global Optimality (GO-FVD model). The new model can be described as: where L is the global length of a road and N is the global number of vehicles ( Figure 1). ( / ) V L N denotes the ideal velocity, which is the function of the average headway / L N and refers to the desired velocity for the uniform flow. (Δ ( )) n V x t is the optimal velocity, which depends on the headway Δ ( ) n x t of vehicle n and represents the desired velocity of the current vehicle. The Global Optimality can be achieved only when the velocities of all vehicles are equal to the ideal velocity. Parameter λ is the coefficient of velocity difference between the ideal velocity and the current velocity. Parameter γ is the coefficient of velocity difference between the ideal velocity and the optimal velocity. Other variables have the same meanings as that in Equations (1) to (3). According to the calibration carried out by Helbing and Tilch [32], the optimal velocity ( (Δ ( )) n V x t ) function and the ideal velocity ( ( / ) V L N ) function in Equation (4) are given by Equations (5) and (6). According to the calibration carried out by Helbing and Tilch [32], the optimal velocity (V(∆x n (t))) function and the ideal velocity (V(L/N)) function in Equation (4) are given by Equations (5) and (6). where l c is the vehicle length, and l c = 5 m. V 1 , V 2 , C 1 and C 2 are parameters, and their estimated values are:

Linear Stability Analysis
Stability analysis is to investigate the influence of perturbations on traffic flow. If the traffic is stable, small perturbation will gradually disappear during the propagation process. Conversely, if the traffic is unstable, small perturbation will propagate upstream along the traffic flow, evolving the traffic flow into traffic congestion gradually. The linear stability of GO-FVD model will be explored using the perturbation analysis method [43]. The specific analysis steps are as follows.
Suppose that vehicles move on a road with the uniform headway b and velocity V(b), then the steady state solution is: where x 0 n (t) is the initial position of vehicle n at time t. Inserting a small perturbation y n (t) = x n (t) − x 0 n (t) and Equation (7) into Equation (4), the linearized equation is obtained by using Taylor expansion: where a k and z are respectively the frequency and wave number. Then y n (t) is expanded according to the Fourier Series. Substituting it into Equation (8), Equation (9) is given: Let z = iω, which is an imaginary number. Equation (10) is deduced using Euler formula exp(ia k ) = cos a k + i sin a k : Assuming the real part and the imaginary part in Equation (10) are both zero, it yields: From Equation (12), Equation (13) is obtained: Substituting Equation (13) into Equation (11) and taking a = α + β + γ, σ = β cos a k , then Further, Equation (15) is deduced from Equation (14): The neutral stability curve (Equation (16)) is obtained by using L'Hospital's rule when a k → 0 . Finally, the linear stability conditions can be obtained.

Numerical Simulations
Numerical simulations can visually replicate the motion characteristics of traffic flow. Thus, the stability, safety and energy dissipation of traffic flow can be investigated by means of numerical simulations. In this study, numerical simulations are performed under the periodic boundary condition by applying Matlab R2016b. The initial simulation state is that N vehicles are uniformly distributed on the road with global length L [21]. In addition, β = 0.2 and the time interval is ∆t = 0.1 s [43]. The perturbation added to the above stable flow is ∆x 1 (0) = 5 m. Values of other parameters are the same as that in Equations (5) and (6). The evolution processes as well as the energy dissipation of traffic flow are simulated by varying the values of parameters λ and γ under different sensitivities. In the simulations, the global number of vehicles is N = 100 and the global length of road is L = 1500 m [21]. Here, the energy dissipation refers to the additional consumption of energy caused by the perturbation. Energy dissipation for vehicle n from time t to t + 1 can be formulated as Equation (17) [46,47].
where m is the vehicle mass, and m = 1500 kg. Then, energy dissipation rate (E d ) is given by Equation (18). Besides, total energy dissipation for each vehicle (E) during time T can be described by Equation (19).

Analytical Results
According to the analytical methods listed in Section 3.2, the linear stability criterion for GO-FVD model is given by The GO-FVD model presented in Equation (4) reduces to OV model when β = 0, λ = 0, γ = 0. Thus, the stability condition is When β 0, λ = 0, γ = 0, the stability condition for FVD model is To display the linear stability results shown in Equations (20) to (22) more intuitively, Figure 2 plots the neutral stability curves for GO-FVD model, FVD model and OV model. The three curves in Figure 2 denote the neutral stability conditions for these three models respectively. The areas below the neutral stability curves are unstable regions and the areas above the curves represent stable regions. One can observe that, compared with OV model (β = 0, λ = 0, γ = 0) and FVD model (β = 0.2, λ = 0, γ = 0), the To display the linear stability results shown in Equations (20) to (22) more intuitively, Figure 2 plots the neutral stability curves for GO-FVD model, FVD model and OV model. The three curves in Figure 2 denote the neutral stability conditions for these three models respectively. The areas below the neutral stability curves are unstable regions and the areas above the curves represent stable regions. One can observe that, compared with OV model (β = 0, λ = 0, γ = 0) and FVD model (β = 0.2, λ = 0, γ = 0), the stable region of GO-FVD model (β = 0.2, λ = 0.15, γ = 0.1) is significantly enlarged. Analytical results indicate that the stability of traffic flow will be enhanced with consideration of Global Optimality.

Evolution Processes of Traffic Flow
The evolution processes of traffic flow are simulated to investigate the effects of Global Optimality on traffic stability and safety.

•
The headway evolutions at low sensitivity The headway evolution of traffic flow is an important indicator for traffic stability, which can reflect the development of traffic congestion. Specifically, the greater the headway fluctuation, the more unstable the traffic flow is. Figure 3 Figure  3d). It is demonstrated that GO-FVD model is more conducive to the stability of traffic flow than FVD model. Traffic congestion will be alleviated accordingly. Moreover, the fluctuations are decreased with the increase of parameters λ and γ. Namely, traffic stability will be strengthened with more consideration given to Global Optimality.

Evolution Processes of Traffic Flow
The evolution processes of traffic flow are simulated to investigate the effects of Global Optimality on traffic stability and safety.
• The headway evolutions at low sensitivity The headway evolution of traffic flow is an important indicator for traffic stability, which can reflect the development of traffic congestion. Specifically, the greater the headway fluctuation, the more unstable the traffic flow is. Figure 3 Figure 3a shows that the headway fluctuates at t = 100 s under different λ and γ due to the small perturbation. Comparing Figure 3a-d, it can be observed that the headway fluctuation for FVD model becomes more and more severe as time goes on, suggesting the traffic congestion may eventually occur. However, as shown in Figure 3c, the headway fluctuation for GO-FVD model (λ = 0.2, γ = 0.2) almost disappears at t = 400 s. Thus, the traffic flow returns to the stable state. Similarly, the traffic flow for GO-FVD model (λ = 0.15, γ = 0.1) will become stable at t = 2000 s as well (Figure 3d). It is demonstrated that GO-FVD model is more conducive to the stability of traffic flow than FVD model. Traffic congestion will be alleviated accordingly. Moreover, the fluctuations are decreased with the increase of parameters λ and γ. Namely, traffic stability will be strengthened with more consideration given to Global Optimality.

•
The acceleration profiles at low sensitivity The severe acceleration fluctuation means that drivers may brake suddenly or accelerate abruptly. Such behaviors are harmful to traffic safety. Thus, the safety of traffic flow can be explored by analyzing acceleration profiles. Figure Figure 4, it is clear that at t = 100 s, the amplitude of acceleration for FVD model (Figure 4a) is greater than that for GO-FVD model (Figure 4b,c). Additionally, at t = 2000 s, the acceleration fluctuation is amplified for FVD model (Figure 4a) but is greatly weakened for GO-FVD model (Figure 4b,c). In particular, the accelerations of all vehicles approach to zero in Figure 4c. These simulation results indicate that Global Optimality can reduce driver's unsafe driving behaviors such as sudden acceleration and deceleration. Furthermore, as parameters λ and γ increase separately, the safety of traffic flow will be improved correspondingly.
Acceleration (m/s 2 ) (a)  Figure 4, it is clear that at t = 100 s, the amplitude of acceleration for FVD model (Figure 4a) is greater than that for GO-FVD model (Figure 4b,c). Additionally, at t = 2000 s, the acceleration fluctuation is amplified for FVD model (Figure 4a) but is greatly weakened for GO-FVD model (Figure 4b,c). In particular, the accelerations of all vehicles approach to zero in Figure 4c. These simulation results indicate that Global Optimality can reduce driver's unsafe driving behaviors such as sudden acceleration and deceleration. Furthermore, as parameters λ and γ increase separately, the safety of traffic flow will be improved correspondingly.

•
The acceleration profiles at low sensitivity The severe acceleration fluctuation means that drivers may brake suddenly or accelerate abruptly. Such behaviors are harmful to traffic safety. Thus, the safety of traffic flow can be explored by analyzing acceleration profiles. Figure Figure 4, it is clear that at t = 100 s, the amplitude of acceleration for FVD model (Figure 4a) is greater than that for GO-FVD model (Figure 4b,c). Additionally, at t = 2000 s, the acceleration fluctuation is amplified for FVD model (Figure 4a) but is greatly weakened for GO-FVD model (Figure 4b,c). In particular, the accelerations of all vehicles approach to zero in Figure 4c. These simulation results indicate that Global Optimality can reduce driver's unsafe driving behaviors such as sudden acceleration and deceleration. Furthermore, as parameters λ and γ increase separately, the safety of traffic flow will be improved correspondingly.
Acceleration (m/s 2 ) (a)   From the simulations of the evolution processes of traffic flow, it is illustrated that, under the strategy with consideration of Global Optimality, traffic stability and safety are improved at both low and high sensitivities. Furthermore, the stability and safety are enhanced with the increase of parameters λ and γ.

Energy Dissipation of Traffic Flow
Energy consumption is another traffic problem that has attracted widespread concern. Unstable traffic flow will result in energy dissipation. This section will study the effects of Global Optimality on energy dissipation of traffic flow by conducting numerical simulations.  Likewise, Figure 7 shows the curves for total energy dissipation E for each vehicle. It is noticeable that at low sensitivity (Figure 7a), energy dissipation E for FVD model (λ = 0, γ = 0) is characterized by rapid growth. But for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2), the growth is relatively slow, and the energy dissipation will not increase further after a sufficiently long time. From the simulations of the evolution processes of traffic flow, it is illustrated that, under the strategy with consideration of Global Optimality, traffic stability and safety are improved at both low and high sensitivities. Furthermore, the stability and safety are enhanced with the increase of parameters λ and γ.

Energy Dissipation of Traffic Flow
Energy consumption is another traffic problem that has attracted widespread concern. Unstable traffic flow will result in energy dissipation. This section will study the effects of Global Optimality on energy dissipation of traffic flow by conducting numerical simulations. Figure 6 illustrates the curves for energy dissipation rate E d under different parameters λ and γ for the cases (a) α = 1.0 and (b) α = 2.0. It is found that at low sensitivity (Figure 6a), E d of traffic flow for FVD model (λ = 0, γ = 0) keeps growing as time goes on. However, E d for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2) decreases gradually and will be dropped with λ and γ increasing separately. Under different values of sensitivity (Figure 6a,b), E d for GO-FVD model is always lower than that for FVD model. At the beginning, the curves fluctuate greatly, which is caused by the velocity fluctuations. From the simulations of the evolution processes of traffic flow, it is illustrated that, under the strategy with consideration of Global Optimality, traffic stability and safety are improved at both low and high sensitivities. Furthermore, the stability and safety are enhanced with the increase of parameters λ and γ.

Energy Dissipation of Traffic Flow
Energy consumption is another traffic problem that has attracted widespread concern. Unstable traffic flow will result in energy dissipation. This section will study the effects of Global Optimality on energy dissipation of traffic flow by conducting numerical simulations.  Likewise, Figure 7 shows the curves for total energy dissipation E for each vehicle. It is noticeable that at low sensitivity (Figure 7a), energy dissipation E for FVD model (λ = 0, γ = 0) is characterized by rapid growth. But for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2), the growth is relatively slow, and the energy dissipation will not increase further after a sufficiently long time. Likewise, Figure 7 shows the curves for total energy dissipation E for each vehicle. It is noticeable that at low sensitivity (Figure 7a), energy dissipation E for FVD model (λ = 0, γ = 0) is characterized by rapid growth. But for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2), the growth is relatively slow, and the energy dissipation will not increase further after a sufficiently long time. In addition, as the value of sensitivity increases to α = 2.0 (Figure 7b), the growth of E becomes slower for both FVD model and GO-FVD model. Nevertheless, energy dissipation for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2) is still less than that for FVD model (λ = 0, γ = 0). In addition, as the value of sensitivity increases to α = 2.0 (Figure 7b), the growth of E becomes slower for both FVD model and GO-FVD model. Nevertheless, energy dissipation for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2) is still less than that for FVD model (λ = 0, γ = 0). The simulation results shown in Figures 6 and 7 are consistent. It is explicit that under IoV conditions, driving strategy with consideration of Global Optimality is beneficial to suppress energy dissipation. Furthermore, as parameters λ and γ increase, energy dissipation will be reduced more significantly.

Applicability of GO-FVD Model
The applicability of GO-FVD model under different average headways is tested in accordance with the numerical methods in Section 3.3. The snapshots of velocity against headway ( In Figure 8a, the average headway of traffic flow is 10 m. In this case, there seems to be only a single point, which means the velocities and headways of all vehicles show little difference as the values of parameters λ and γ change. In other words, Global Optimality has little effect on traffic flow when the average headway is 10 m. In Figure 8b, the average headway increases from 10 m to 15 m. The snapshots of velocity against headway form the approximate loops under certain value sets of λ and γ. It is found that the sizes of the approximate loops become progressively small with λ and γ increasing, indicating the traffic stability and safety are strengthened. As both λ and γ increase to 0.2 in Figure 8b, the loop shrinks to be only a point that represents the stable state. However, with the average headway increasing to 20 m in Figure 8c, the loop has shrunk to the stable point as both λ and γ just increase to 0.1. The results indicate that under larger average headway, Global Optimality plays a more active role in smoothing traffic. Velocity (m/s) The simulation results shown in Figures 6 and 7 are consistent. It is explicit that under IoV conditions, driving strategy with consideration of Global Optimality is beneficial to suppress energy dissipation. Furthermore, as parameters λ and γ increase, energy dissipation will be reduced more significantly.

Applicability of GO-FVD Model
The applicability of GO-FVD model under different average headways is tested in accordance with the numerical methods in Section 3.3. The snapshots of velocity against headway ( In Figure 8a, the average headway of traffic flow is 10 m. In this case, there seems to be only a single point, which means the velocities and headways of all vehicles show little difference as the values of parameters λ and γ change. In other words, Global Optimality has little effect on traffic flow when the average headway is 10 m. In Figure 8b, the average headway increases from 10 m to 15 m. The snapshots of velocity against headway form the approximate loops under certain value sets of λ and γ. It is found that the sizes of the approximate loops become progressively small with λ and γ increasing, indicating the traffic stability and safety are strengthened. As both λ and γ increase to 0.2 in Figure 8b, the loop shrinks to be only a point that represents the stable state. However, with the average headway increasing to 20 m in Figure 8c, the loop has shrunk to the stable point as both λ and γ just increase to 0.1. The results indicate that under larger average headway, Global Optimality plays a more active role in smoothing traffic. In addition, as the value of sensitivity increases to α = 2.0 (Figure 7b), the growth of E becomes slower for both FVD model and GO-FVD model. Nevertheless, energy dissipation for GO-FVD model (λ = 0.15, γ = 0.1; λ = 0.2, γ = 0.2) is still less than that for FVD model (λ = 0, γ = 0). The simulation results shown in Figures 6 and 7 are consistent. It is explicit that under IoV conditions, driving strategy with consideration of Global Optimality is beneficial to suppress energy dissipation. Furthermore, as parameters λ and γ increase, energy dissipation will be reduced more significantly.

Applicability of GO-FVD Model
The applicability of GO-FVD model under different average headways is tested in accordance with the numerical methods in Section 3.3. The snapshots of velocity against headway ( In Figure 8a, the average headway of traffic flow is 10 m. In this case, there seems to be only a single point, which means the velocities and headways of all vehicles show little difference as the values of parameters λ and γ change. In other words, Global Optimality has little effect on traffic flow when the average headway is 10 m. In Figure 8b, the average headway increases from 10 m to 15 m. The snapshots of velocity against headway form the approximate loops under certain value sets of λ and γ. It is found that the sizes of the approximate loops become progressively small with λ and γ increasing, indicating the traffic stability and safety are strengthened. As both λ and γ increase to 0.2 in Figure 8b, the loop shrinks to be only a point that represents the stable state. However, with the average headway increasing to 20 m in Figure 8c, the loop has shrunk to the stable point as both λ and γ just increase to 0.1. The results indicate that under larger average headway, Global Optimality plays a more active role in smoothing traffic. Velocity (m/s) Similarly, in Figure 9a, the average headway of traffic flow is 10 m. All vehicles on the whole road have similar velocities under different λ and γ. It is explicit that Global Optimality has little effect on traffic flow in this case. From Figure 9b, where the average headway increases to 15 m, one can observe that on some road segments, for instance, the positions near 1000 m or 5000 m, the velocities of vehicles approach to zero when Global Optimality is not considered (λ = 0, γ = 0). At the same time, the velocities of vehicles on some other segments, for instance, the positions near 4000 m, are more than 13 m/s when λ = 0, γ = 0. It indicates that without consideration of Global Optimality, traffic congestion may occur in some segments while drivers on some other segments may drive at a too high velocity that is unsafe. As λ and γ increase, the minimum velocity is increased, and the maximum velocity is decreased. Correspondingly, with consideration of Global Optimality, traffic congestion is alleviated, and traffic safety is improved. Particularly, when λ = 0.2 and γ = 0.2, velocities of all vehicles evolve to 4.66 m/s which is the ideal velocity for traffic flow with average headway of 15 m. In Figure 9c, where the average headway is 20 m, velocities approach to the corresponding ideal velocity when λ and γ just increase to 0.1. The results accord with those in Figure 8.
Conclusively, GO-FVD model proposed in this paper is especially suitable for the case of larger average headway, which corresponds to the low-density traffic. In this situation, taking Global Optimality into account will enhance the stability and safety of traffic flow markedly.

Conclusions
In this study, a hypothesis is proposed that the traffic will be improved by considering Global Optimality under IoV conditions. To investigate the effects of Global Optimality on traffic, GO-FVD Similarly, in Figure 9a, the average headway of traffic flow is 10 m. All vehicles on the whole road have similar velocities under different λ and γ. It is explicit that Global Optimality has little effect on traffic flow in this case. From Figure 9b, where the average headway increases to 15 m, one can observe that on some road segments, for instance, the positions near 1000 m or 5000 m, the velocities of vehicles approach to zero when Global Optimality is not considered (λ = 0, γ = 0). At the same time, the velocities of vehicles on some other segments, for instance, the positions near 4000 m, are more than 13 m/s when λ = 0, γ = 0. It indicates that without consideration of Global Optimality, traffic congestion may occur in some segments while drivers on some other segments may drive at a too high velocity that is unsafe. As λ and γ increase, the minimum velocity is increased, and the maximum velocity is decreased. Correspondingly, with consideration of Global Optimality, traffic congestion is alleviated, and traffic safety is improved. Particularly, when λ = 0.2 and γ = 0.2, velocities of all vehicles evolve to 4.66 m/s which is the ideal velocity for traffic flow with average headway of 15 m. In Figure 9c, where the average headway is 20 m, velocities approach to the corresponding ideal velocity when λ and γ just increase to 0.1. The results accord with those in Figure 8.
Conclusively, GO-FVD model proposed in this paper is especially suitable for the case of larger average headway, which corresponds to the low-density traffic. In this situation, taking Global Optimality into account will enhance the stability and safety of traffic flow markedly.

Conclusions
In this study, a hypothesis is proposed that the traffic will be improved by considering Global Optimality under IoV conditions. To investigate the effects of Global Optimality on traffic, GO-FVD model is formulated. The main improvement of GO-FVD model is that the average headway of traffic flow is selected to describe the overall situation of the traffic on a certain road. Since the average headway can be easily obtained under IoV conditions, the model is practical. Furthermore, the adverse effects of transfer delays can be weakened because the average headway of traffic flow on a certain road is relative stable information. Based on GO-FVD model, linear stability analysis and numerical simulations are conducted to explore the specific effects of Global Optimality on traffic stability, safety as well as energy dissipation.
Analytical results indicate that the stability region is enlarged in GO-FVD model, which means traffic stability is enhanced with consideration of Global Optimality. Numerical simulations agree well with analytical results. The main findings are as follows: (1) At low sensitivity, the small perturbation added to traffic flow propagates upstream in FVD model and ultimately leads to the unstable and unsafe flow. Conversely, for GO-FVD model, the perturbation is absorbed by degrees and the traffic flow returns to stable and safe state eventually. (2) At high sensitivity, traffic flow for GO-FVD model evolves to uniform flow earlier than that for FVD model. (3) Energy dissipation for GO-FVD model is explicitly less than that for FVD model. Conclusively, Global Optimality is conductive to the improvement of traffic stability and safety as well as the reduction of energy dissipation. Accordingly, these findings have verified the hypothesis proposed in the study. In addition, it is illustrated that Global Optimality plays a more active role in improving traffic with low density.
The model proposed in this study can provide theoretical reference for further study with respect to traffic problems. The findings of this study will help to support the driving tasks in the environment of IoV and promote the sustainable development of intelligent transportation. Nevertheless, there are still some limitations in the current work. In practice, weather and road characteristics will also influence the traffic, which are neglected in GO-FVD model. Noticeably, these factors are not mutually exclusive to Global Optimality. Thus, for a more realistic representation of traffic situations, GO-FVD model can be extended by accounting for these factors. Besides, the effects of Global Optimality should be tested with field data. In the current work, however, since the IoV has not been widely applied in practice, these data are lacking. Consequently, more investigations could focus on these problems in future study.