Comprehensive Review on Main Topologies of Impedance Source Inverter Used in Electric Vehicle Applications

: Power electronics play a fundamental role for electric transportation, renewable energy conversion and many other industrial applications. They have the ability to help achieve high e ﬃ ciency and performance in power systems. However, traditional inverters such as voltage source and current source inverters present some limitations. Consequently, many research e ﬀ orts have been focused on developing new power electronics converters suitable for many applications. Compared with the conventional two-stage inverter, Z-source inverter (ZSI) is a single-stage converter with lower design cost and high e ﬃ ciency. It is a power electronics circuit of which the function is to convert DC input voltage to a symmetrical AC output voltage of desired magnitude and frequency. Recently, ZSIs have been widely used as a replacement for conventional two-stage inverters in the distributed generation systems. Several modiﬁcations have been carried out on ZSI to improve its performance and e ﬃ ciency. This paper reviews the-state-of-art impedance source inverter main topologies and points out their applications for multisource electric vehicles. A concise review of main existing topologies is presented. The basic structural di ﬀ erences, advantages and limitations of each topology are illustrated. From this state-of-the-art review of impedance source inverters, the embedded quasi-Z-source inverter presents one of the promising architectures which can be used in multisource electric vehicles, with better performance and reliability. The utilization of this new topology will open the door to several development axes, with great impact on electric vehicles (EVs).


Introduction
The strong energy demand in our society results from increased consumption and population growth [1]. This energy demand leads to a scarcity of fossil fuels and creates ecological problems. The automotive sector is at the heart of these concerns, and it invokes the research and development of

Z-Source Inverter
As mentioned in the introduction, the ZSI is a topology appeared in the scientific literature, through the work of F.Z. Peng, in the article published in 2003 [3]. This topology is characterized by the existence of impedance network formed by the inductors and capacitors between the source of input and the inverter stage. The ZSI has the particular ability to use inverter switches to raise the DC bus voltage. The converter equipped with an impedance network of LC type arranged in "X" allows the simultaneous closure of up and down switches of the same inverter arm to perform its function of raising the voltage, v dc . Figure 1 shows the topology of bidirectional ZSI feeding AC load. ZSI has a unique characteristic of buck-boost capability, which permits it to have wide voltage range. Then, ZSI offers novel power conversion concept. Simultaneous triggering of both switches from the same leg of ZSI does not cause any failure, because the inductor of current fed ZSI can sustain high current. However, ZSI is not suitable for very low input DC voltages [25]. It cannot suppress the inrush current and also produces discontinuous input source current [26]. There are also different grounds for source and inverter circuits [27]. High-voltage capacitors are required, leading to an increase to the cost and volume of the system [26]. In recent years, many Z-source single-phase inverters have been proposed [12][13][14][15][16][17][18].
World Electric Vehicle Journal 2020, x, x; doi: 3 of 20 As mentioned in the introduction, the ZSI is a topology appeared in the scientific literature, through the work of F.Z. Peng, in the article published in 2003 [3]. This topology is characterized by the existence of impedance network formed by the inductors and capacitors between the source of input and the inverter stage. The ZSI has the particular ability to use inverter switches to raise the DC bus voltage. The converter equipped with an impedance network of LC type arranged in "X" allows the simultaneous closure of up and down switches of the same inverter arm to perform its function of raising the voltage, . Figure 1 shows the topology of bidirectional ZSI feeding AC load. ZSI has a unique characteristic of buck-boost capability, which permits it to have wide voltage range. Then, ZSI offers novel power conversion concept. Simultaneous triggering of both switches from the same leg of ZSI does not cause any failure, because the inductor of current fed ZSI can sustain high current. However, ZSI is not suitable for very low input DC voltages [25]. It cannot suppress the inrush current and also produces discontinuous input source current [26]. There are also different grounds for source and inverter circuits [27]. High-voltage capacitors are required, leading to an increase to the cost and volume of the system [26]. In recent years, many Z-source single-phase inverters have been proposed [12][13][14][15][16][17][18].

Quasi-Z-source Inverter
By rearranging the components in the Z-source network, a new topology called quasi-Z-source Inverter (QZSI) was proposed by Anderson and Peng in 2008 [28]. It was inspired by the typical ZSI, and it is mainly applied in motor systems, new energy systems and micro-grid systems. Quasi-source is the first modification of the Z-source network that overcomes the drawbacks of Z-source network. The quasi-source inverter has a lot of advantages, such as reducing the switching stress of the switches and the passive component ratings, which enhance the efficiency and reliability of the inverter. According to the operational modes in voltage-type or current-type and continuous or discontinuous current, quasi-Z-source inverters can be classified into four categories. We can have the voltage-fed quasi-Z-source inverters with continuous input current, voltage-fed quasi-Z-source inverters with discontinuous input current, current-fed quasi-Z-source inverters with continuous input current and current-fed quasi-Z-source inverters with discontinuous input current [27]. Different kinds of QZSI feeding AC loads are shown in Figure 2. The QZSI topology shown in Figure 2a presents the advantage of having a continuous input current and retains all the merits of the ZSI, making it a good candidate for EV applications, renewable energy generation and many other power-conversion applications [29].

Quasi-Z-Source Inverter
By rearranging the components in the Z-source network, a new topology called quasi-Z-source Inverter (QZSI) was proposed by Anderson and Peng in 2008 [28]. It was inspired by the typical ZSI, and it is mainly applied in motor systems, new energy systems and micro-grid systems. Quasi-source is the first modification of the Z-source network that overcomes the drawbacks of Z-source network. The quasi-source inverter has a lot of advantages, such as reducing the switching stress of the switches and the passive component ratings, which enhance the efficiency and reliability of the inverter. According to the operational modes in voltage-type or current-type and continuous or discontinuous current, quasi-Z-source inverters can be classified into four categories. We can have the voltage-fed quasi-Z-source inverters with continuous input current, voltage-fed quasi-Z-source inverters with discontinuous input current, current-fed quasi-Z-source inverters with continuous input current and current-fed quasi-Z-source inverters with discontinuous input current [27]. Different kinds of QZSI feeding AC loads are shown in Figure 2. The QZSI topology shown in Figure 2a presents the advantage of having a continuous input current and retains all the merits of the ZSI, making it a good candidate for EV applications, renewable energy generation and many other power-conversion applications [29].

Embedded Z-Source Inverter
The embedded Z-source inverter was proposed to achieve smaller volume and higher robustness [30]. This impedance source inverter uses the concept of embedding the input DC sources within the LC impedance network. For the situation where implicit source filtering is critical, the embedded Z-source inverter represents one of the important alternatives. The embedded-Z-source inverter produces continuous input current. It also maintains the features of typical Z-source inverters and is able to produce smaller ripples of input voltage and current. It is able to draw a smooth current from a source, without adding another component. The main inconvenient of the embedded Z-source inverter constitutes the stress distribution among the components provided by its asymmetrical structure. Figure 3 shows the typical topology of a two-level-embedded ZSI. Its multisource feature is suitable for PV-power generation [30] and battery storage systems.

Embedded Quasi-Z-Source Inverter
The embedded quasi-Z-source inverter (EQZSI) maintains the features of typical quasi-Z-source inverter and is also able to produce smaller ripples of input voltage and continuous current [31,32]. It is able to draw a smooth current from a source, without adding other components. Figure 4 shows typical topology of an EQZSI. In this configuration, an additional DC source is embedded in the DC link of the classical QZSI. The concept of embedding the DC source permits to inherit the advantages of both QZSI and embedded topologies. The EQZSI topology enables it to operate well with one or voltage-fed one with discontinuous current (b); current-fed one with continuous current (c); current-fed one with discontinuous current (d).

Embedded Z-Source Inverter
The embedded Z-source inverter was proposed to achieve smaller volume and higher robustness [30]. This impedance source inverter uses the concept of embedding the input DC sources within the LC impedance network. For the situation where implicit source filtering is critical, the embedded Z-source inverter represents one of the important alternatives. The embedded-Z-source inverter produces continuous input current. It also maintains the features of typical Z-source inverters and is able to produce smaller ripples of input voltage and current. It is able to draw a smooth current from a source, without adding another component. The main inconvenient of the embedded Z-source inverter constitutes the stress distribution among the components provided by its asymmetrical structure. Figure 3 shows the typical topology of a two-level-embedded ZSI. Its multisource feature is suitable for PV-power generation [30] and battery storage systems.

Embedded Z-Source Inverter
The embedded Z-source inverter was proposed to achieve smaller volume and higher robustness [30]. This impedance source inverter uses the concept of embedding the input DC sources within the LC impedance network. For the situation where implicit source filtering is critical, the embedded Z-source inverter represents one of the important alternatives. The embedded-Z-source inverter produces continuous input current. It also maintains the features of typical Z-source inverters and is able to produce smaller ripples of input voltage and current. It is able to draw a smooth current from a source, without adding another component. The main inconvenient of the embedded Z-source inverter constitutes the stress distribution among the components provided by its asymmetrical structure. Figure 3 shows the typical topology of a two-level-embedded ZSI. Its multisource feature is suitable for PV-power generation [30] and battery storage systems.

Embedded Quasi-Z-Source Inverter
The embedded quasi-Z-source inverter (EQZSI) maintains the features of typical quasi-Z-source inverter and is also able to produce smaller ripples of input voltage and continuous current [31,32]. It is able to draw a smooth current from a source, without adding other components. Figure 4 shows typical topology of an EQZSI. In this configuration, an additional DC source is embedded in the DC link of the classical QZSI. The concept of embedding the DC source permits to inherit the advantages of both QZSI and embedded topologies. The EQZSI topology enables it to operate well with one or

Embedded Quasi-Z-Source Inverter
The embedded quasi-Z-source inverter (EQZSI) maintains the features of typical quasi-Z-source inverter and is also able to produce smaller ripples of input voltage and continuous current [31,32]. It is able to draw a smooth current from a source, without adding other components. Figure 4 shows typical topology of an EQZSI. In this configuration, an additional DC source is embedded in the DC link of the classical QZSI. The concept of embedding the DC source permits to inherit the advantages of World Electric Vehicle Journal 2020, 11, 37 5 of 17 both QZSI and embedded topologies. The EQZSI topology enables it to operate well with one or two sources, without altering the voltage gain of QZSI topology. Its operating principle can be described in two states: the non-shoot-through state and the shoot-through one, like quasi-Z-source network. It can be suitable for battery storage systems and multisource power-conversion systems. Other similar embedded topologies with one or two DC sources also exist.
World Electric Vehicle Journal 2020, x, x; doi: 5 of 20 two sources, without altering the voltage gain of QZSI topology. Its operating principle can be described in two states: the non-shoot-through state and the shoot-through one, like quasi-Z-source network. It can be suitable for battery storage systems and multisource power-conversion systems.
Other similar embedded topologies with one or two DC sources also exist.

Trans-Z-Source Inverter
In theory, Z-source, quasi-Z-source, embedded Z-source and embedded quasi-Z-source all have unlimited voltage gain. However, in practice, a high voltage gain can impose high voltage stress on the switches. To overcome the aforementioned problem, Trans-Z-source (two voltage-fed and two current-fed) inverters were proposed to have higher voltage gains and to keep voltage stress low with Z-source network reduced to one transformer (or one coupled inductor) and one capacitor [33]. Trans-Z-source inverters not only maintain the main features of traditional Z-source inverters, but also exhibit some unique advantages by increasing voltage gains and reducing voltage stress. They are also able to operate at very low input voltage. The Trans-Z-source network has the operation and working principle similar to Z-source network and also eliminates the shoot-through barriers. However, transformers and coupled inductors which are used in its design increase volume and cost. Figure 5 shows the typical topology of Trans-Z-source inverter. This topology is very suitable for renewable energy generation [34].

Y-Source Inverter
Y-source inverter is designed based on the Trans-Z-source inverter. The performance of the Ysource network inverter is close to that of the Trans-Z-source inverter. Y-source inverter topology was proposed in [16], using coupled inductors with three windings transformer (N1, N2 and N3). It has one more degree of freedom, such as the three windings and shoot-through duty cycle of switches. This degree of freedom permits users to choose the boost voltage comparatively to a classical impedance network design with boost converter. It reduces the total harmonic distortion (THD) of the inverter and realizes a higher voltage gain with small shoot-through duty cycle. The higher voltage boost and higher modulation index can be obtained at the same time with Y-source inverter. The Y-source impedance network also has the operation and working principle similar to the Z-source network. However, its leakage inductances of the coupled inductor due to discontinuous input current can produce the voltage overshoots [35]. With the diverse properties and

Trans-Z-Source Inverter
In theory, Z-source, quasi-Z-source, embedded Z-source and embedded quasi-Z-source all have unlimited voltage gain. However, in practice, a high voltage gain can impose high voltage stress on the switches. To overcome the aforementioned problem, Trans-Z-source (two voltage-fed and two current-fed) inverters were proposed to have higher voltage gains and to keep voltage stress low with Z-source network reduced to one transformer (or one coupled inductor) and one capacitor [33]. Trans-Z-source inverters not only maintain the main features of traditional Z-source inverters, but also exhibit some unique advantages by increasing voltage gains and reducing voltage stress. They are also able to operate at very low input voltage. The Trans-Z-source network has the operation and working principle similar to Z-source network and also eliminates the shoot-through barriers. However, transformers and coupled inductors which are used in its design increase volume and cost. Figure 5 shows the typical topology of Trans-Z-source inverter. This topology is very suitable for renewable energy generation [34].
World Electric Vehicle Journal 2020, x, x; doi: 5 of 20 two sources, without altering the voltage gain of QZSI topology. Its operating principle can be described in two states: the non-shoot-through state and the shoot-through one, like quasi-Z-source network. It can be suitable for battery storage systems and multisource power-conversion systems.
Other similar embedded topologies with one or two DC sources also exist.

Trans-Z-Source Inverter
In theory, Z-source, quasi-Z-source, embedded Z-source and embedded quasi-Z-source all have unlimited voltage gain. However, in practice, a high voltage gain can impose high voltage stress on the switches. To overcome the aforementioned problem, Trans-Z-source (two voltage-fed and two current-fed) inverters were proposed to have higher voltage gains and to keep voltage stress low with Z-source network reduced to one transformer (or one coupled inductor) and one capacitor [33]. Trans-Z-source inverters not only maintain the main features of traditional Z-source inverters, but also exhibit some unique advantages by increasing voltage gains and reducing voltage stress. They are also able to operate at very low input voltage. The Trans-Z-source network has the operation and working principle similar to Z-source network and also eliminates the shoot-through barriers. However, transformers and coupled inductors which are used in its design increase volume and cost. Figure 5 shows the typical topology of Trans-Z-source inverter. This topology is very suitable for renewable energy generation [34].

Y-Source Inverter
Y-source inverter is designed based on the Trans-Z-source inverter. The performance of the Ysource network inverter is close to that of the Trans-Z-source inverter. Y-source inverter topology was proposed in [16], using coupled inductors with three windings transformer (N1, N2 and N3). It has one more degree of freedom, such as the three windings and shoot-through duty cycle of switches. This degree of freedom permits users to choose the boost voltage comparatively to a classical impedance network design with boost converter. It reduces the total harmonic distortion (THD) of the inverter and realizes a higher voltage gain with small shoot-through duty cycle. The higher voltage boost and higher modulation index can be obtained at the same time with Y-source inverter. The Y-source impedance network also has the operation and working principle similar to the Z-source network. However, its leakage inductances of the coupled inductor due to discontinuous input current can produce the voltage overshoots [35]. With the diverse properties and

Y-Source Inverter
Y-source inverter is designed based on the Trans-Z-source inverter. The performance of the Y-source network inverter is close to that of the Trans-Z-source inverter. Y-source inverter topology was proposed in [16], using coupled inductors with three windings transformer (N1, N2 and N3). It has one more degree of freedom, such as the three windings and shoot-through duty cycle of switches. This degree of freedom permits users to choose the boost voltage comparatively to a classical impedance network design with boost converter. It reduces the total harmonic distortion (THD) of the inverter and realizes a higher voltage gain with small shoot-through duty cycle. The higher voltage boost and higher modulation index can be obtained at the same time with Y-source inverter. The Y-source impedance network also has the operation and working principle similar to the Z-source network. However, its leakage inductances of the coupled inductor due to discontinuous input current can produce the voltage overshoots [35]. With the diverse properties and the specific future of the Y-source network, many researchers and engineers continue to examine and modify the topology for the wide range of power-conversion applications. Figure 6 shows the Y-source inverter main topology.
World Electric Vehicle Journal 2020, x, x; doi: 6 of 20 the specific future of the Y-source network, many researchers and engineers continue to examine and modify the topology for the wide range of power-conversion applications. Figure 6 shows the Ysource inverter main topology.

Γ-Z-Source Inverter
Γ-Z-source inverter is also derived from Trans-Z-source inverter [36]. Two Γ-shaped inductors are coupled in Trans-Z-source inverter to form the Γ-Z-source inverter, permitting it to increase the gain and modulation ratio, simultaneously [36]. The Γ-Z-source network gain is increased by decreasing the turn ratio. Figure 7 shows the Γ-Z-source inverter topology. Unlike other impedance source inverter whose gains increase with an increased turns ratio, such as Trans-Z-source and LCCT-Z-source, the Γ-Z-source inverter uses fewer components and a coupled transformer to achieve a high voltage gain by lowering the turn ratio. It represents the impedance source inverter which provides a better spectral performance. The drawback of this topology constitutes the presence of the leakage inductance that can affect the voltage and current stress on semiconductors. This topology is more convenient for renewable-energy generation.

LCCT-Z-Source Inverter
As shown in Figure 8, the LCCT-Z-source inverter is extended from the Trans-Z-source. LCCT-Z-source network is an inductor-capacitor-capacitor-transformer Z-source network [17]. It can also be represented as an integration of high-frequency transformer with quasi-Z-source inverter. This topology produces continuous current even during light load and filters out high-frequency ripples from source current. It is able to achieve higher voltage gain and modulation index [18]. The unique feature of the LCCT-Z-source inverter is that its network helps to prevent the transformer core from saturation due to two capacitors, which block the source current [37], and during the boost operation, only one inductive element is used to store the energy. The LCCT-Z-source inverter is appropriate for renewable-energy generation and power-conversion applications.

Γ-Z-Source Inverter
Γ-Z-source inverter is also derived from Trans-Z-source inverter [36]. Two Γ-shaped inductors are coupled in Trans-Z-source inverter to form the Γ-Z-source inverter, permitting it to increase the gain and modulation ratio, simultaneously [36]. The Γ-Z-source network gain is increased by decreasing the turn ratio. Figure 7 shows the Γ-Z-source inverter topology. Unlike other impedance source inverter whose gains increase with an increased turns ratio, such as Trans-Z-source and LCCT-Z-source, the Γ-Z-source inverter uses fewer components and a coupled transformer to achieve a high voltage gain by lowering the turn ratio. It represents the impedance source inverter which provides a better spectral performance. The drawback of this topology constitutes the presence of the leakage inductance that can affect the voltage and current stress on semiconductors. This topology is more convenient for renewable-energy generation.
World Electric Vehicle Journal 2020, x, x; doi: 6 of 20 the specific future of the Y-source network, many researchers and engineers continue to examine and modify the topology for the wide range of power-conversion applications. Figure 6 shows the Ysource inverter main topology.

Γ-Z-Source Inverter
Γ-Z-source inverter is also derived from Trans-Z-source inverter [36]. Two Γ-shaped inductors are coupled in Trans-Z-source inverter to form the Γ-Z-source inverter, permitting it to increase the gain and modulation ratio, simultaneously [36]. The Γ-Z-source network gain is increased by decreasing the turn ratio. Figure 7 shows the Γ-Z-source inverter topology. Unlike other impedance source inverter whose gains increase with an increased turns ratio, such as Trans-Z-source and LCCT-Z-source, the Γ-Z-source inverter uses fewer components and a coupled transformer to achieve a high voltage gain by lowering the turn ratio. It represents the impedance source inverter which provides a better spectral performance. The drawback of this topology constitutes the presence of the leakage inductance that can affect the voltage and current stress on semiconductors. This topology is more convenient for renewable-energy generation.

LCCT-Z-Source Inverter
As shown in Figure 8, the LCCT-Z-source inverter is extended from the Trans-Z-source. LCCT-Z-source network is an inductor-capacitor-capacitor-transformer Z-source network [17]. It can also be represented as an integration of high-frequency transformer with quasi-Z-source inverter. This topology produces continuous current even during light load and filters out high-frequency ripples from source current. It is able to achieve higher voltage gain and modulation index [18]. The unique feature of the LCCT-Z-source inverter is that its network helps to prevent the transformer core from saturation due to two capacitors, which block the source current [37], and during the boost operation, only one inductive element is used to store the energy. The LCCT-Z-source inverter is appropriate for renewable-energy generation and power-conversion applications.

LCCT-Z-Source Inverter
As shown in Figure 8, the LCCT-Z-source inverter is extended from the Trans-Z-source. LCCT-Z-source network is an inductor-capacitor-capacitor-transformer Z-source network [17]. It can also be represented as an integration of high-frequency transformer with quasi-Z-source inverter. This topology produces continuous current even during light load and filters out high-frequency ripples from source current. It is able to achieve higher voltage gain and modulation index [18]. The unique feature of the LCCT-Z-source inverter is that its network helps to prevent the transformer core from saturation due to two capacitors, which block the source current [37], and during the boost operation, only one inductive element is used to store the energy. The LCCT-Z-source inverter is appropriate for renewable-energy generation and power-conversion applications.
be represented as an integration of high-frequency transformer with quasi-Z-source inverter. This topology produces continuous current even during light load and filters out high-frequency ripples from source current. It is able to achieve higher voltage gain and modulation index [18]. The unique feature of the LCCT-Z-source inverter is that its network helps to prevent the transformer core from saturation due to two capacitors, which block the source current [37], and during the boost operation, only one inductive element is used to store the energy. The LCCT-Z-source inverter is appropriate for renewable-energy generation and power-conversion applications.

Advantages and Disadvantages of the Main Impedance Source Network Topologies
The main impedance source network topologies exhibit several advantages and disadvantages. Table 1 shows the summary of the impedance source network topologies. Table 2 shows the main impedance source network topologies' advantages and disadvantages. Their applications with the typical used power are also shown in Table 3. From the study of these various main impedance source inverters, we can see that the EQZSI is a promising architecture for multisource EV. It presents the advantage of having a continuous input current and retaining all the merits of both QZSI and embedded topologies.

Number of Inductors
Voltage Stress on the Switching Device Trans-Z-Source # 5 One inductor and one 2 windings coupled inductor Table 2. Summary of the impedance source network topologies' advantages and disadvantages.

Impedance Network Advantages Disadvantages
Z-Source -Overcomes the disadvantages of voltage source and current source inverters.
-Offers novel power conversion concept.
-Both switches from the same leg trigger at the same time do not cause any failure.
-Inductor of current fed ZSI sustains high current.
-Benefits to motor drives and renewable-energy-generation applications.
-Not suitable for very low input DC voltages [25].
-Cannot suppress the inrush current.
-Different grounds for source and inverter circuits [26].
-High-voltage capacitors, which are required, increase the cost and volume of the system.
-The shoot-through duty ratio must always be less than 0.5.
-Reduces passive component ratings.
-Provides lower current stress on inductors compared to ZSI.
-Shares common ground with input DC supply [26].
-Benefits to motor drives and renewable-energy-generation applications.
-The shoot-through duty ratio must always be less than 0.5.
-Not suitable for very low input DC voltage.
Embedded Z-Source -Draws smooth current from source, without additional component.
-Produce smaller ripples of input voltage and current.
-Suitable for battery storage systems and PV-power generation.
-Different stress distribution among components, provided by its asymmetrical structure.
-Supplied current is no longer maintained.
-The shoot-through-duty ratio must always be less than 0.5. -Have high winding-turns ratio.
-Electromagnetic interference noise affects its reliability. Table 3. Summary of the impedance source inverter applications with typical used power.

Z-Source Inverters for Single-Source EV Applications
The efficient use of the available resources is one of the greatest technological concerns. With the ZSI, the improvements in DC-DC systems are going on in the field of EVs. The ZSI can regulate the voltages and currents of the energy sources and enables bidirectional flow of power in traction applications. In the propulsion mode, the voltage from the energy storage systems is provided by the ZSI, in the form of three-phase voltage, to drive the motor to produce the required torque and reach the desired speed of the vehicle. During the regenerative mode, the electric motor acts as a generator. The regenerated energy flows backward, to recharge the energy sources. The inverter operates as a rectifier, and the ZSI works as buck inverter, to recharge the energy sources. The schematic of the diagram of EV system components using an impedance source inverter is shown in Figure 9. Since 2003, ZSI has been widely used in industrial applications, as well as in in a variety of other applications. ZSI has been applied to motor drives, to overcome the restrictions of voltage source inverter [13]. Bidirectional QZSI, which is the first modified topology of bidirectional ZSI, has also been compared with bidirectional conventional two-stage inverter for electric traction systems [49]. The results demonstrate that the transient and the steady-state performances are comparable for both topologies under the same operating conditions. However, the bidirectional QZSI shows lower inductor current ripples than bidirectional conventional two-stage inverter. The results also prove that the bidirectional QZSI shows higher efficiency than the conventional solution. Bidirectional ZSI, Since 2003, ZSI has been widely used in industrial applications, as well as in in a variety of other applications. ZSI has been applied to motor drives, to overcome the restrictions of voltage source inverter [13]. Bidirectional QZSI, which is the first modified topology of bidirectional ZSI, has also been compared with bidirectional conventional two-stage inverter for electric traction systems [49].
The results demonstrate that the transient and the steady-state performances are comparable for both topologies under the same operating conditions. However, the bidirectional QZSI shows lower inductor current ripples than bidirectional conventional two-stage inverter. The results also prove that the bidirectional QZSI shows higher efficiency than the conventional solution. Bidirectional ZSI, which can operate in boost mode, buck mode as a normal voltage source inverter, or a charger mode and applied to double-ended inverter drive system, is also proposed in [50]. To investigate the performance of locomotive drives, the ZSI has been used as a replacement for a voltage source inverter [51].
Because of many advantages of ZSI, it is suitably applied for fuel cell. A fuel-cell configuration using a Z-source network was represented in [52]. Three different inverters, namely a traditional voltage source inverter, conventional two-stage inverter and ZSI applied to a fuel-cell vehicle, have been compared [53]. The result shows that the ZSI has higher efficiency, less switching devices and more passive components requirement than the others type of inverters.

Z-Source Inverter for Multisource EV Applications
EV performance can be influenced by a lot of factors, including size, purpose of use, environment and driving style. For EV, these factors may lead to a deep and quick discharge rate of the battery. EV powered by a combination of multiple sources can contribute to keep the battery in good health [54]. That also helps the battery to slowly discharge, even when the EV uses a heavy load [55]. A hybrid energy storage system (HESS) combining two or more energy sources (batteries, ultracapacitor and fuel cell) has been shown to be a suitable solution, as it can meet the load-power requirement needed, depending on the characteristics of each source [56]. The conventional two-stage inverters are normally employed in these HESS.
In order to exploit the advantages of ZSIs, ultracapacitor-battery HESS for EVs based on asymmetric bidirectional Z-source topology has been studied [57]. The results demonstrate that the HESS with ZSI can be integrated into the traction system to obtain better performance and lower cost than that with conventional two-stage inverters. Furthermore, the ZSI can also be applied to hybrid electric vehicles using a fuel cell and battery as input sources, with slight modification in its topology [58]. Nonetheless, this configuration has some disadvantages with the obligation to use a high-voltage battery and the fact that the DC link voltage has twice the battery voltage during regenerative braking when the fuel cell stack is disconnected from the ZSI input terminals. This disconnection may damage the switches of the inverter.
There are many impedance source inverters which can be used for multisource EVs, such embedded Z-source inverter, embedded quasi-Z-source inverter and other topologies obtained with slight modification to include a battery or an additional DC source [58]. However, a multisource supply system for EVs with different power flows in traction and braking operations can be designed with bidirectional EQZSI. The EQZSI is a promising architecture for the multisource electric vehicle, as it presents the advantages of having a continuous input current and retaining all the merits of both QZSI and embedded topology [59].

Bidirectional EQZSI for Multisource EV Applications Electric Vehicle Specifications and Modeling
The reference electric vehicle is the e-TESC 4W platform, as presented in [59], with its main parameters. In our study, a permanent magnet synchronous machine (PMSM) was used as a traction electric motor, and its state space representation can be described as presented in [49].

Modeling of Bidirectional Embedded Quasi-Z-Source Inverter
The bidirectional EQZSI, as presented in Section 2.4, can buck and boost the input voltage in a single stage with two control variables, namely the shoot-through duty ratio and the modulation index. Assuming T is one switching cycle, T 0 is the interval of the shoot-through state and T 1 is the interval of non-shoot-through state, their relationship is T 0 + T 1 = T, and the shoot-through duty ratio is D = T 0 T . The dynamic equations can be described as shown in [59]. During the steady state, the capacitor voltages and inductor currents can be deduced as follows: The DC link peak voltage,v dc , can be derived from the sum of two capacitor voltages, v c1 and v c2 , as follows:v where B ≥ 1 is the boost factor resulting from the shoot through the period. With regards to the AC side of the EQZSI, the peak phase voltage can be written as follows: where m e and G e are the inverter modulation index and total voltage gain of the EQZSI, respectively.

PI-Based Controllers Design
To achieve the speed control and disturbance rejection for the EV, cascade PI controllers were designed. The motor (PMSM) with PI control technique was adopted. The speed control scheme for EQZSI is shown in Figure 10.

Simulation Results and Discussion
A simulation was carried out, to validate the model of EQZSI and show its performance for multisource EV. The bidirectional EQZSI performance depends on the selection of the parameters of embedded quasi-Z-source network elements. There are equations which can be used to determine the appropriate values of these parameters [60]. The critical values of the inductances and the

Simulation Results and Discussion
A simulation was carried out, to validate the model of EQZSI and show its performance for multisource EV. The bidirectional EQZSI performance depends on the selection of the parameters of embedded quasi-Z-source network elements. There are equations which can be used to determine the appropriate values of these parameters [60]. The critical values of the inductances and the capacitances are used to design the EQZSI parameters by the following equations: where D is the shoot-through duty ratio, f s is the switching frequency, v c1 is the average capacitor voltage, ∆i L1 is the value of inductor current ripple at peak power to certain value, i L1 is the average current of the inductor and ∆v c1 represents the value of capacitor voltage ripple at peak power. The simulation parameters are L 1 = L 2 = 230 µH; C 1 = C 2 = 2.2 mF. PWM carrier frequency for three-phase inverter is 10 kHz. The control scheme is shown in Section 3.2.1. Maximum constant boost control method as shown in [59] has been used to generate the gate signals of the EQZSI switches.
The electric vehicle motor used in the simulation is a PMSM with three phases, as defined in Section 3.2.1. The parameters of the motor are L d = L q = 1 mH; r s = 0.08 Ω; p = 2; ψ f = 0.1 Wb. The rated power is 15 kW. Figures 11 and 12 show the speed and torque waveforms, respectively. Figures 13 and 14              The results point out the ability of the inverter to respond quickly to the mechanical load and provide a DC bus constant voltage over all the power-demand profile. These results verify the bidirectional EQZSI as an alternative inverter for multisource EVs. The disparity of voltage levels and currents between the sources (fuel cell, batteries and ultracapacitors) and the loads of the EVs (traction motor and auxiliaries) requires the use of power converters. This kind of power-converter architecture provides a new interesting resource for on-board energy management in multisource EVs. The bidirectional EQZSI can enhance the performance of the EV by optimizing the electric power consumption and extending its driving range.

Future Trends
The concept of impedance source inverter has clearly opened up a new area of research in the field of power electronics. The study in Section 2 provides only a brief summary on topologies of impedance source inverters. It also shows the modifications that are possible to have with ZSI. Any topology possesses its own unique features and adapted applications. New impedance source inverters' topologies may continue to appear to meet needs and improve performance in different applications. EVs, motor drives and renewable energy generation will be perspective applications for impedance source inverters, as impedance source inverters have a unique voltage buck-boost ability with minimum number of components and potential reduced cost. The control strategy is very important, as it ensures reliable and efficient operation of the impedance source inverter. The impedance source inverter system's performance will be improved with novel control method. The use of a control method such as model predictive control (MPC) can contribute to enhance impedance source inverter system performance. The cost function of MPC is fundamental to the system performance, and different constraints can be added to improve the complete functioning of the system. The performance of impedance source inverters will also be enhanced with the new power electronics devices, such as the SiC and GaN, since they have high switching frequency, high temperature capacity and expected low cost. That can contribute to achieve smaller size for passive components of impedance source inverter, to reduce its cost and to increase its efficiency. The design of new impedance source inverters has attracted more and more attention from scientists and engineers. Impedance source inverter is still progressing in terms of topologies and applications.

Conclusions
A comprehensive start-of-the-art review of impedance source inverter main topologies was presented. The impedance source inverter for EV application and for other applications was outlined. Several topologies of ZSI were investigated. Many impedance source inverters were compared, in order to choose the best, most efficient and most convenient inverter topology for multisource EV. In the literature, a lot of approaches have been proposed, and their benefits and drawbacks were identified. The advantages and disadvantages of the impedance source inverter main topologies were presented. The impedance network becomes popular by the fact that it has specific features and attractive power-conversion ability. Impedance source inverters overcome many problems of traditional inverters. Since the apparition of Z-source network, numerous contributions in the literature modifying the basic topology to suit the needs of many applications have been proposed. It has been advanced to quasi-Z-source network, embedded Z-source network, embedded quasi-Z-source network, Trans-Z-source network and many other types of Z-source network topologies. The EQZSI is one of the promising architectures which can be used in EV multisource, with better performance and reliability. The utilization of this new topology will open the door to several development axes, with great impacts on EVs. Various researchers continue to work toward the modification of impedance source inverter main topologies, to increase their performance and applicability.