Microwave-Reactor-Based Preparation of Red Iron Oxide Pigment from Waste Iron Sulfate

This article presents a two-step method of iron red synthesis based on waste long-term deposited iron(II) sulfate. The first step is the purification of waste iron sulfate, and then the pigment is synthesized by precipitation using a microwave reactor. The newly developed method of purification allows for quick and thorough purification of iron salt. The use of a microwave reactor in the synthesis of iron red makes it possible to reduce the temperature of the goethite–hematite phase transition from 500 °C to 170 °C and skip the calcination process. A temperature reduction in the synthesis decreases the formation of agglomerates of synthesized materials compared to commercial ones. The results of the research showed a change in the physicochemical properties of the obtained pigments depending on the conditions of synthesis. Waste iron(II) sulfate is a promising raw material for the synthesis of iron red pigments. Laboratory pigments are found to be differ from commercial pigments. The difference in properties speaks in favor of synthesized materials.


Introduction
As far as iron pigment manufacturing is concerned, precipitation and Penniman Zoph processes are the most commonly used procedures [1]. Using either process, there can be pigments produced with a wide range of colors that are associated with iron oxides and oxide-hydroxides. In this way, with minor process modifications, yellow, orange, red, and black pigments can be synthesized.
The main raw material that is used in both a precipitation and the Penniman-Zoph process is iron(II) sulfate. It is also relevant to note that the Penniman-Zoph procedure also takes into account the use of waste sulfate, e.g., from the production of TiO 2 or from steel etching [2]. It is critical for this raw material, however, to be relatively fresh, nonoxidized, and free of any colored metal add-ons such as chromium or manganese compounds. The presence of additional colored oxides has a negative effect on the color of the pigment.
A natural development of the existing technologies [1,3] is to use chemical waste and check whether the obtained products are different from those made from pure raw materials. Chemical waste that can be used for the synthesis of iron pigments in accordance with the concept of "waste to materials" is increasingly being sought. The publication [4] uses iron sand from Dlodo beach in Tulungangung on the island of Java to obtain yellow and red pigments. The authors of the publication [5] derived coke from bituminous shale for the synthesis of hybrid red iron pigments. Waste from the production of stainless steel was repurposed by the authors of the article [6]. They used oily mill scale, which is a byproduct of hot rolling steel. The authors of [7,8] investigated the hydrochemical conversion of goethite (FeOOH) to magnetite (Fe 3 O 4 ) in high-iron Bauxite residue. The iron-rich residues can be used in the steel industry or as a pigment. In the Chinese patents [9,10], the method for obtaining iron pigments from waste iron sulfate was developed. However, the

Purification of Waste FeSO 4
The preparation of iron pigments from waste FeSO 4 requires prior purification of insoluble components and doped metal ions. The work uses a developed method of purifying waste FeSO 4 by recrystallization [30].
For purification, a saturated waste FeSO 4 solution in 10% sulfuric acid was prepared. A total of 130 g of waste FeSO 4  was crystallized by cooling (5 • C), and the crystals of purified FeSO 4 were separated from the filtrate. The performed process is illustrated in the schematic diagram in Figure 1.  (5 °C), and the crystals of purified FeSO4 were separated from the filtrate. The performed process is illustrated in the schematic diagram in Figure 1.

Preparation of Iron Pigments
The effect of the concentration of starting solutions on the synthesis of iron pigments was investigated. For this purpose, salt solutions with concentrations of 10, 14, 21, and 28 wt% of purified FeSO4 were prepared. Accordingly, the names of the synthesized pigment samples were introduced: CZ 10%, CZ 14%, CZ 21%, and CZ 28%.
First, the assumed amounts of purified FeSO4·7H2O (7.5 g; 10 g; 15 g; 20 g) were stirred at room temperature until they formed a transparent solution in aqua (~15 mL). For the oxidation, stoichiometric amounts of hydrogen peroxide (30 wt%) were used (1).
Then, to precipitate the iron hydroxide, 25 wt% ammonia water was added in stoichiometric amounts (2).
Suspension was then transferred into a Teflon container, filled with water to a volume of 70 mL (Teflon container volume 100 mL), and placed in the microwave reactor (Ertec Magnum II) where the reaction was carried out for one hour at a pressure range of 17-20 bar and a temperature of 170 °C. At the end of the period, the resulting suspensions were washed with water and dried at 105 °C for 4 h.

Preparation of Iron Pigments
The effect of the concentration of starting solutions on the synthesis of iron pigments was investigated. For this purpose, salt solutions with concentrations of 10, 14, 21, and 28 wt% of purified FeSO 4 were prepared. Accordingly, the names of the synthesized pigment samples were introduced: CZ 10%, CZ 14%, CZ 21%, and CZ 28%.
Then, to precipitate the iron hydroxide, 25 wt% ammonia water was added in stoichiometric amounts (2).
Suspension was then transferred into a Teflon container, filled with water to a volume of 70 mL (Teflon container volume 100 mL), and placed in the microwave reactor (Ertec Magnum II) where the reaction was carried out for one hour at a pressure range of 17-20 bar and a temperature of 170 • C. At the end of the period, the resulting suspensions were washed with water and dried at 105 • C for 4 h.

Analytical Methods
The chemical composition of waste and purified FeSO 4 was determined by quantitative analysis with the ICP-OES method (Perkin Elmer Avio 500, Waltham, MA, USA). The content of Fe(II) and Fe(III) was quantified by manganometric titration [31]. The amount of XRD patterns were collected with an X-ray diffractometer (Empyrean, Malvern Panalytical, Malvern, UK) equipped with a Cu-Kα radiation source (Nickel filter; λ = 0.15418 nm, 40 kV, 35 mA). Scans were taken at room temperature in scattering 2θ range of 10-100 • with a step interval of about 0.026 • . Phase composition was determined using Panalytical X'Pert HighScore Plus v3.0 software with the ICDD PDF4+ database. Fourier transform infrared spectroscopy (FTIR) spectra of the sample were measured in a range of 4000-400 cm −1 on a Nicolet 380 spectrometer (Thermo Fisher Scientific, Waltham, MA, USA) and the sample was mixed with KBr at a ratio of 1:100 and then compressed into tablets. The surface composition of pigments was analyzed with X-ray photoelectron spectroscopy (XPS). The photoelectron measurements were conducted with Mg Ka (hν = 1253.6 eV) radiation in a Prevac system equipped with Scienta SES 2002 electron energy analyzer operating at constant transmission energy (Ep = 50 eV). The pressure in the analysis chamber was kept under 1·10 −9 mbar. The specific surface area of pigments was determined by the Brunauer-Emmett-Teller (BET) method using the Quadrasorb Evo Quantachrome Instruments nitrogen adsorption apparatus. A sample was degassed at 100 • C under a high vacuum for 16 h. Dynamic light scattering measurements (DLS) were carried out on the Horiba LA 950 Laser Diffraction Particle Size Analyzer. A sample was dispersed in 50 mL of 0.1% sodium pyrophosphate solution. Then, the solution was sonicated in an ultrasonic cleaner for 2 min. The prepared dispersion was loaded into the analyzer. In the measurements, a reflectance coefficient of 2.90 was used, and sonication was turned on. The surface morphology of samples was observed with an emission scanning electron microscope VEGA 3 (TESCAN, Brno, Czech Republic). A sample was dispersed in isopropyl alcohol, and 2 µL were placed on silicon wafers and evaporated. Oil absorption was determined according to the PN-EN ISO 787-5:1999 standard. Table 1 presents the chemical composition of the salt, determined by the ICP-OES method. The content of iron ions was determined by manganometric titration. Besides iron(II) and(III) ions, the waste FeSO 4 contained admixtures of other metals in the form of ions such as titanium, magnesium, calcium, potassium, sodium, manganese, and others.

Results and Discussion
The content of iron ions was determined by manganometric titration; (b) detection limit.
The content of a significant part of Fe 3+ ions (8.7 + −0.2 wt%) proves that the Fe 2+ ions contained in the waste FeSO 4 , as a result of long-term storage, were oxidized by atmospheric air. In addition, high levels of magnesium and titanium indicate residues of undecomposed titanium ore. The purification process allowed for a decrease in the content of elements such as Mg, Ca, Na, Zn, and Ti. Recrystallization also increased the content of Fe 2+ ions in a sample, which is also a positive effect of this process. During the removal of impurities, iron ions are also removed to a small extent. The iron losses are insignificant considering how low the contaminants level achieved after purification is. Figure 2 shows the diffractograms of (a) waste FeSO 4 and (b) purified FeSO 4 . Two phases of iron(II) sulfate heptahydrate (ICDD No.: 04-010-4265) and iron(III) hydroxide sulfate pentahydrate (ICDD No.: 00-016-0935) were identified in the waste material, which is marked in the diffraction pattern. As a result of the recrystallization process, a salt was obtained in which one crystalline phase was identified, derived from iron(II) sulfate heptahydrate (ICDD No.: 04-010-4265). Figure 2 shows the diffractograms of (a) waste FeSO4 and (b) purified FeSO4. Two phases of iron(II) sulfate heptahydrate (ICDD No.: 04-010-4265) and iron(III) hydroxide sulfate pentahydrate (ICDD No.: 00-016-0935) were identified in the waste material, which is marked in the diffraction pattern. As a result of the recrystallization process, a salt was obtained in which one crystalline phase was identified, derived from iron(II) sulfate heptahydrate (ICDD No.: 04-010-4265). So far, attempts have been made to develop a method for treating waste long-deposited iron(II) sulfate. However, these methods either use fresh salt with low amounts of impurities and Fe 3+ [32] or rely on complex chemical reactions, taking into account redox reactions or impurity precipitation [33,34]. These methods are much more complicated compared to the method described in the article. Figure 3 shows X-ray powder diffraction (XRPD) diffractograms of the laboratory pigments.

XRD
As can be seen, the samples consist of hematite (ICDD No.: 00-024-0072). Samples contain, in addition to partially crystallized compounds, a significant amount of the amorphous phase. The broad bases of the reflection (110) suggest that hematite was formed by dehydration of goethite [35]. Red lines indicate places where goethite remnants can be seen in the diffraction pattern (ICDD No.: 01-073-8431). So far, attempts have been made to develop a method for treating waste long-deposited iron(II) sulfate. However, these methods either use fresh salt with low amounts of impurities and Fe 3+ [32] or rely on complex chemical reactions, taking into account redox reactions or impurity precipitation [33,34]. These methods are much more complicated compared to the method described in the article.    As can be seen, the samples consist of hematite (ICDD No.: 00-024-0072). Samples contain, in addition to partially crystallized compounds, a significant amount of the amorphous phase. The broad bases of the reflection (110) suggest that hematite was formed by dehydration of goethite [35]. Red lines indicate places where goethite remnants can be seen in the diffraction pattern (ICDD No.: 01-073-8431). Figure 4 shows the diffraction patterns of commercial pigments and the pigment CZ 14%. Figure 4 shows the diffraction patterns of commercial pigments and the pigment CZ 14%.
The diffraction patterns of commercial pigments show reflections characteristic of the hematite phase (ICDD No.: 00-024-0072). In addition to hematite, the reflections characteristic of silica (green lines) (ICDD No.: 01-080-2148) are visible in the Commercial pigment C diffraction pattern.

FT-IR
On the obtained FT-IR spectra ( Figure 5) can be observed a band of vibrations typical of iron oxides from the Fe-O bond A [11,[36][37][38] at positions of about 480 cm −1 and 560 cm −1 . The next characteristic bands appear at positions 800 cm −1 , 900-990 cm −1 , and 1450 cm −1 and they correspond to the vibrations typical of the O-H bond B [11,36]. The band C is characteristic of the bending vibrations of the O-H groups [11,37]. The last, wide band with a maximum at the position of about 3400 cm −1 is representative of the water absorbed on the sample surface, and more specifically for the stretching vibrations of the O-H groups D [11,[37][38][39]. According to the literature, the higher the crystallization of the materials, the greater the shift of the characteristic bands that is observed [36].

FT-IR
On the obtained FT-IR spectra ( Figure 5) can be observed a band of vibrations typical of iron oxides from the Fe-O bond A [11,[36][37][38] at positions of about 480 cm −1 and 560 cm −1 . The next characteristic bands appear at positions 800 cm −1 , 900-990 cm −1 , and 1450 cm −1 and they correspond to the vibrations typical of the O-H bond B [11,36]. The band C is characteristic of the bending vibrations of the O-H groups [11,37]. The last, wide band with a maximum at the position of about 3400 cm −1 is representative of the water absorbed on the sample surface, and more specifically for the stretching vibrations of the O-H groups D [11,[37][38][39]. According to the literature, the higher the crystallization of the materials, the greater the shift of the characteristic bands that is observed [36].
In commercial pigments, apart from the characteristic bands described earlier, in one sample there are also other compounds. Thus, for the sample of Commercial pigment C, at the values of about 750 cm −1 and 1100 cm −1 , there is a band characteristic of the Si-O bond E [40]. Then, at the value of about 1530 cm −1 , vibrations originating from the Ca-O bond F [41] occur, and at about 2500 cm −1 , a low-intensity band G [42,43], originating from CO2, appears. This indicates the presence, in addition to silica, of calcite (CaCO3), which is a fairly popular surface treatment agent. The surface of CZ 14% pigment as well as those of Commercial pigments C and D were analyzed by X-ray photoelectron spectroscopy ( Figure 6). These tests showed that the surfaces of all three materials contain predominantly oxygen atoms and iron atoms from iron In commercial pigments, apart from the characteristic bands described earlier, in one sample there are also other compounds. Thus, for the sample of Commercial pigment C, at the values of about 750 cm −1 and 1100 cm −1 , there is a band characteristic of the Si-O bond E [40]. Then, at the value of about 1530 cm −1 , vibrations originating from the Ca-O bond F [41] occur, and at about 2500 cm −1 , a low-intensity band G [42,43], originating from CO 2 , appears. This indicates the presence, in addition to silica, of calcite (CaCO 3 ), which is a fairly popular surface treatment agent.

XPS
The surface of CZ 14% pigment as well as those of Commercial pigments C and D were analyzed by X-ray photoelectron spectroscopy ( Figure 6). These tests showed that the surfaces of all three materials contain predominantly oxygen atoms and iron atoms from iron oxides, the main component of pigments. The only contamination on the surface of the CZ 14% pigment is "adventitious carbon", usually occurring on the surface of materials prepared by wet synthesis. Analysis of the surface of Commercial pigment C confirms the conclusions of diffractometric methods and FTIR analysis, i.e., traces of silicon and calcium atoms, presumably from oxides of these metals, is observed on the surface. Traces of chlorine were identified on the surface of Commercial pigment D. rials 2023, 16, x FOR PEER REVIEW Figure 6. The survey XPS spectra of CZ 14% and Commercial pigments C and A detailed analysis of the chemical state of iron in the three mentio also performed. The XPS spectrum of Fe 2p is shown in Figure 7. This a the chemical state of iron in all the analyzed pigments is identical, indic of the same iron compounds. XPS analysis of complex iron-oxygen com not allow a conclusive distinction of the chemical states of iron prese under study. This is particularly difficult in the case of the presence o oxides. In the present study, by comparing the shape of the Fe 2p lin determined that the material most likely contains Fe 3+ iron ions [44]. A detailed analysis of the chemical state of iron in the three mentioned pigments was also performed. The XPS spectrum of Fe 2p is shown in Figure 7. This analysis shows that the chemical state of iron in all the analyzed pigments is identical, indicating the presence of the same iron compounds. XPS analysis of complex iron-oxygen compounds often does not allow a conclusive distinction of the chemical states of iron present in the material under study. This is particularly difficult in the case of the presence of a mixture of iron oxides. In the present study, by comparing the shape of the Fe 2p line envelope, it was determined that the material most likely contains Fe 3+ iron ions [44]. Laboratory pigments have an isothermal shape that corresponds to type V according to the IUPAC classification [45,46]. This is a typical characteristic of mesoporous materials. The hysteresis shape corresponds to the E type, i.e., spherically elongated or bottle-shaped pores with open ends. The shape of the adsorption isotherms for commercial pigments also corresponds to isotherms for mesoporous materials, but with a much lower adsorption capacity.   Laboratory pigments have an isothermal shape that corresponds to type V according to the IUPAC classification [45,46]. This is a typical characteristic of mesoporous materials. The hysteresis shape corresponds to the E type, i.e., spherically elongated or bottle-shaped pores with open ends. The shape of the adsorption isotherms for commercial pigments also corresponds to isotherms for mesoporous materials, but with a much lower adsorption capacity.  Laboratory pigments have an isothermal shape that corresponds to type V according to the IUPAC classification [45,46]. This is a typical characteristic of mesoporous materials. The hysteresis shape corresponds to the E type, i.e., spherically elongated or bottle-shaped pores with open ends. The shape of the adsorption isotherms for commercial pigments also corresponds to isotherms for mesoporous materials, but with a much lower adsorption capacity.
Synthesized pigments have up to 20 times greater specific surface area than commercial pigments (Figure 9). The differences in results can be explained by the method of sample synthesis-commercial pigments obtain their proper structure at the stage of high-temperature calcination [1,11,47]. The temperature of the goethite-hematite transformation is 450 • C, while during calcination the temperature is much higher and reaches over 600 • C. That difference promotes the sintering of the pigment and the disappearance of the developed specific surface. In the literature [48,49], hematite obtained at a temperature of 450 • C has a specific surface area in the range of 25-40 m 2 /g, which is 3-4 times larger than the characterized commercial iron pigments. In the case of synthesized pigments, it is visible that the higher the amorphous phase content in the samples, the higher the specific surface area of the material. Sample CZ 14%, containing well-crystallized hematite, shows a value of the specific surface area close to the value in the literature [48,49]. Synthesized pigments have up to 20 times greater specific surface area than commercial pigments (Figure 9). The differences in results can be explained by the method of sample synthesis-commercial pigments obtain their proper structure at the stage of hightemperature calcination [1,11,47]. The temperature of the goethite-hematite transformation is 450 °C, while during calcination the temperature is much higher and reaches over 600 °C. That difference promotes the sintering of the pigment and the disappearance of the developed specific surface. In the literature [48,49], hematite obtained at a temperature of 450 °C has a specific surface area in the range of 25-40 m 2 /g, which is 3-4 times larger than the characterized commercial iron pigments. In the case of synthesized pigments, it is visible that the higher the amorphous phase content in the samples, the higher the specific surface area of the material. Sample CZ 14%, containing well-crystallized hematite, shows a value of the specific surface area close to the value in the literature [48,49]. As per the definition proposed by the European Commission [50], all obtained laboratory materials that have a surface area of more than 60 m 2 /cm 3 can be considered "nanomaterials". Figure 10 shows the particle size distribution for laboratory and commercial pigments.  As per the definition proposed by the European Commission [50], all obtained laboratory materials that have a surface area of more than 60 m 2 /cm 3 can be considered "nanomaterials". Figure 10 shows the particle size distribution for laboratory and commercial pigments.

DLS
Synthesized pigments have up to 20 times greater specific surface area than commercial pigments (Figure 9). The differences in results can be explained by the method of sample synthesis-commercial pigments obtain their proper structure at the stage of hightemperature calcination [1,11,47]. The temperature of the goethite-hematite transformation is 450 °C, while during calcination the temperature is much higher and reaches over 600 °C. That difference promotes the sintering of the pigment and the disappearance of the developed specific surface. In the literature [48,49], hematite obtained at a temperature of 450 °C has a specific surface area in the range of 25-40 m 2 /g, which is 3-4 times larger than the characterized commercial iron pigments. In the case of synthesized pigments, it is visible that the higher the amorphous phase content in the samples, the higher the specific surface area of the material. Sample CZ 14%, containing well-crystallized hematite, shows a value of the specific surface area close to the value in the literature [48,49]. As per the definition proposed by the European Commission [50], all obtained laboratory materials that have a surface area of more than 60 m 2 /cm 3 can be considered "nanomaterials". Figure 10 shows the particle size distribution for laboratory and commercial pigments.  Most of the commercial pigments presented here have a wide particle size distribution. In Commercial pigment A and Commercial pigment C samples, the majority of the particles are in the range of 0-500 nm with a small proportion (<10%) of larger particles. The rest of the commercial pigments show primarily particles in the 2-9 µm range, with a small proportion (<10%) of particles smaller than 2 µm or larger than 9 µm. Due to the sonication of the suspension during the measurements, particle sedimentation can be excluded [11,51].

DLS
In the case of laboratory pigments, the obtained materials were mostly characterized by a particle distribution in the range of 0.1-1 µm. The CZ 14% and CZ 10% samples had the highest proportion of particles in the 100-500 nm range; the proportion of particles of this size in these samples was circa 90%.
3.1.6. Pigment Observation on SEM Figure 11 shows SEM photos. by a particle distribution in the range of 0.1-1 µm. The CZ 14% and CZ 10% samples had the highest proportion of particles in the 100-500 nm range; the proportion of particles of this size in these samples was circa 90%.
3.1.6. Pigment Observation on SEM Figure 11 shows SEM photos. Laboratory pigments do not show such strong agglomeration. In the case of the CZ 14% sample, the photos show individual plates about 300 nm in size, which is consistent with the results of the DLS analysis. Several aggregates of particles are also observed. In the case of the CZ 28% sample, the pigment structure is not as distinguishable as in the case of the CZ 14% sample. The photos show agglomerates of particles. Blue particles are single particles up to 500 nm in size. Agglomerates of particles > 500 nm with single particles highlighted are green. Orange granules are individual particles forming agglomerates with a size of 100-600 nm. Pink particles are aggregates of particles < 2µm with indistinguishable single particles. Particles are irregular with spherical shape [11].

Oil Absorption
According to the technical sheets that were obtained regarding the product, each of the commercial pigments should have an oil absorption of a maximum of 35 g/100 g (rl) based on the product technical sheets. All of the values for the commercial pigments exceed 10 to 30 percent of the reference values ( Figure 12). For laboratory materials, pigments synthesized at low concentrations are characterized by lower values of the oil absorption than pigments synthesized at a concentration > 20 wt%. Laboratory pigments do not show such strong agglomeration. In the case of the CZ 14% sample, the photos show individual plates about 300 nm in size, which is consistent with the results of the DLS analysis. Several aggregates of particles are also observed. In the case of the CZ 28% sample, the pigment structure is not as distinguishable as in the case of the CZ 14% sample. The photos show agglomerates of particles. Blue particles are single particles up to 500 nm in size. Agglomerates of particles > 500 nm with single particles highlighted are green. Orange granules are individual particles forming agglomerates with a size of 100-600 nm. Pink particles are aggregates of particles < 2µm with indistinguishable single particles. Particles are irregular with spherical shape [11].

Oil Absorption
According to the technical sheets that were obtained regarding the product, each of the commercial pigments should have an oil absorption of a maximum of 35 g/100 g (rl) based on the product technical sheets. All of the values for the commercial pigments exceed 10 to 30 percent of the reference values ( Figure 12). For laboratory materials, pigments synthesized at low concentrations are characterized by lower values of the oil absorption than pigments synthesized at a concentration > 20 wt%.

Conclusions
This study developed a purification method for waste FeSO4, and then a method for synthesizing red iron pigments using purified FeSO4. Results of the study indicate that recrystallization is an effective method of purifying waste long-term storage iron(II) sulfate, allowing the iron(II) content to increase while reducing the impurities-especially

Conclusions
This study developed a purification method for waste FeSO 4 , and then a method for synthesizing red iron pigments using purified FeSO 4 . Results of the study indicate that recrystallization is an effective method of purifying waste long-term storage iron(II) sulfate, allowing the iron(II) content to increase while reducing the impurities-especially coloring compounds, which affect the pigment color (Mn compounds). In addition, the developed purification method does not require complicated equipment or many chemical reagents.
XRD measurements of the pigment samples from different concentrations confirm that the prepared nanoparticles consist mostly of hematite phase, also supported by FTIR results. Results showed that the pigment synthesized from a solution of 14% iron salt had the most crystallized hematite when compared to other pigments. This may be related to the suspension:total reactor volume ratio and the fact that the growth of hematite crystals is controlled only by kinetic factors. In the coprecipitation process, two stages are involved: a short burst of nucleation occurs when the concentration of the species reaches critical supersaturation, and then there is a slow growth of crystals [52,53]. The optimal concentration of iron sulfate based on research can be 10-20% (49-92 mM) with an optimum of 14 wt% (66 mM).
In addition, synthesis using the microwave reactor is reproducible. Laboratory pigments do not show strong agglomeration. The CZ 14% sample shows individual plates about 300 nm in size, while the CZ 28% sample shows agglomerates of particles. The SEM study found that laboratory pigment particles aggregate less than commercial pigments. In addition, synthesized pigments have some irregular spherical shapes. High surface area (>60 m 2 /g) of the nanoparticles synthesized with mesoporous structure was performed by BET. In addition, the XRD and XPS analyses revealed the purity of the hematite nanoparticles. The oil absorption of most pigments synthesized in the laboratory was in the range of 23-39 g/100 g of pigment and was in the range declared for commercial pigments (max. 35 g/100 g).
Based on the obtained findings, it can be concluded that waste long-term storage iron(II) sulfate is a potential raw material for the production of iron pigments. On this basis, pigments are obtained with physicochemical properties comparable to commercially available pigments, and their suggested use is in the dyeing industry.