Eu-Doped Zeolitic Imidazolate Framework-8 Modified Mixed-Crystal TiO2 for Efficient Removal of Basic Fuchsin from Effluent

Zeolitic imidazolate framework-8 (ZIF-8) was doped with a rare-earth metal, Eu, using a solvent synthesis method evenly on the surface of a mixed-crystal TiO2(Mc-TiO2) structure in order to produce a core–shell structure composite ZIF-8(Eu)@Mc-TiO2 adsorption photocatalyst with good adsorption and photocatalytic properties. The characterisation of ZIF-8(Eu)@Mc-TiO2 was performed via X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller analysis (BET) and ultraviolet–visible light differential reflectance spectroscopy (UV-DRs). The results indicated that Eu-doped ZIF-8 was formed evenly on the Mc-TiO2 surface, a core–shell structure formed and the light-response range was enhanced greatly. The ZIF-8(Eu)@Mc-TiO2 for basic fuchsin was investigated to validate its photocatalytic performance. The effect of the Eu doping amount, basic fuchsin concentration and photocatalyst dosage on the photocatalytic efficiency were investigated. The results revealed that, when 5%-Eu-doped ZIF-8(Eu)@Mc-TiO2 (20 mg) was combined with 30 mg/L basic fuchsin (100 mL) under UV irradiation for 1 h, the photocatalytic efficiency could reach 99%. Further, it exhibited a good recycling performance. Thus, it shows certain advantages in its degradation rate and repeatability compared with previously reported materials. All of these factors suggested that, in an aqueous medium, ZIF-8(Eu)@Mc-TiO2 is an eco-friendly, sustainable and efficient material for the photocatalytic degradation of basic fuchsin.


Introduction
Dyes are widely used in various industries to colour industrial products, such as foods, cosmetics, leather, plastics and paper [1]. Large amounts of water containing these dyes are discharged in the environment, and these organic dyes present a threat to human and aquatic health because they are extremely water-soluble, nonbiodegradable, chemically stable and carcinogenic [2,3]. Basic fuchsin is a kind of triphenylmethane dye that is widely used in the dyeing of cotton, nylon, leather and paper [4]. Regular contact can affect the central nervous system, induce dizziness, drowsiness and muscle contractions, and can even cause cancer [5].
Several separation techniques, such as physical adsorption, electrochemical oxidation, biodegradation and Fenton oxidation, are used for the decolourisation and removal of these wastes from the water [6]. However, such traditional methods are often expensive and cause secondary pollution. Photocatalytic degradation is regarded as an ideal and economically feasible method because infinite solar energy can be applied to induce the redox reaction without any other type of energy resource [7]. To efficiently utilise solar energy to remove dyes from water, it is essential to design a highly active photocatalyst [8]. Thus far, many researchers have been extensively studying and testing various classes of photocatalytic materials in order to achieve the photochemical degradation of dyes [9].
Titanium dioxide (TiO 2 ) is a nontoxic photocatalytic material with excellent physical and chemical properties, such as good stability and a strong oxidation ability [10]. The photocatalytic activity of TiO 2 is mainly related to its crystal phase, morphology and size [11]. A large number of studies have confirmed that the photocatalytic activity of mixed-crystal TiO 2 is better than that of single-crystal TiO 2 [12]. Photogenerated electrons and holes can migrate from one phase to another through the two-phase interface, which can effectively separate the photogenerated electrons and holes, inhibit the recombination of the two and improve the quantum yield of the material [13]. Therefore, the preparation of mixed-crystal TiO 2 micro/nanomaterials is an effective method for obtaining high-performance catalysts. In addition, the rapid recombination of photogenerated carriers is also an important factor hindering the enhancement of photocatalytic activity [14]. Therefore, avoiding the agglomeration of TiO 2 and reducing the recombination of photogenerated carriers has become another research focus.
Metal-organic frameworks (MOFs) comprise a class of new porous materials that are widely used, especially in catalysis, adsorption, separation and gas storage, as well as in other fields [15]. A typical representative of zeolitic imidazolate frameworks (ZIFs), ZIF-8, has a metal imidazole unit bond length that is longer than that of the molecular sieve [16], and a pore cage diameter greater than that of the molecular sieve [17]. As a result, ZIF-8 has a larger specific surface area and pore size [18]. Many studies have reported that MOFs loaded on the surface of photocatalysts could not only increase the contact area between the photocatalyst and pollutants to adsorb organic dye and avoid the agglomeration of photocatalysts, but could also improve the degradation performance of photocatalysts [19,20].
Rare-earth (RE) metal doping or deposition is an effective method for photocatalytic performance [21]. RE metals are rich in 4f electronic conformation and can form complexes with Lewis bases, including organic acids, ethanol and thiols, thereby effectively changing the crystal structure, electronic conformation and optical properties [22,23]. RE ion doping not only resists the recombination of the photocatalyst's photogenerated electrons and holes, but also broadens the spectral response range of photocatalysts and improves their photocatalytic ability [24]. Europium is the most active of RE metals. The electronic configuration of europium is [Xe] 4f 7 5s 2 5p 6 6s 2 . Due to the fact that the 4f orbital of Eu is incompletely filled, the electrons in this orbital are easily shielded by sub-outer electrons, resulting in the complex linear spectral properties of Eu ions. The introduction of Eu 3+ ions into the matrix material can cause lattice defects of the matrix material, increase the surface-active sites of the material, improve the valence band position of the matrix material and increase the absorption of visible light. Thus, the resulting composite nanomaterials have a good performance in the fields of luminescence, new energy development and utilisation. In addition, there was no toxicity of europium compounds, and even some of the europium compounds could be used for future therapeutic alternative treatment strategies for some diseases [25]. Doping current photocatalytic materials with Eu is also considered a promising material preparation strategy for photocatalysts.
In this work, we prepare mixed-crystal structure TiO 2 (Mc-TiO 2 ) and creatively distribute ZIF-8 doped by RE metal Eu using a solvent synthesis method evenly on the surface of the mixed-crystal TiO 2 structure to produce a core-shell structure composite material ZIF-8(Eu)@Mc-TiO 2 adsorption photocatalyst with good adsorption and photocat-Materials 2021, 14, 7265 3 of 14 alytic properties. The photocatalytic performance of the synthesised ZIF-8(Eu)@Mc-TiO 2 was investigated with basic fuchsin as the target degradation product of aerobic organic pollutants; satisfactory results were obtained. The effects of the Eu doping amount, basic fuchsin concentration and photocatalyst dosage on the photocatalytic efficiency of ZIF-8(Eu)@Mc-TiO 2 for basic fuchsin were investigated, and its regeneration ability was examined through several photocatalytic cycles. Thus, ZIF-8(Eu)@Mc-TiO 2 was found to exhibit a good recycling performance as well. The degradation rate of ZIF-8(Eu)@Mc-TiO 2 for basic fuchsin could reach 99%, and, compared with previously reported materials, it shows certain advantages in terms of its degradation rate and repeatability. This study provides valuable theoretical explorations and technical experiments for the large-scale treatment of industrial wastewater containing basic fuchsin by ZIF-8(Eu)@Mc-TiO 2 . First, 10 mL absolute ethanol, 2.5 mL deionised water, 5 mL glacial acetic acid and 1 mL polyethylene glycol 400 (PEG-400) were placed into beaker A and 15 mL absolute ethanol was placed into beaker B. Then, 10 mL tetrabutyl titanate was slowly added to beaker A and stirred using a magnetic stirrer (HJ-6A, Changzhou, China) until the solution was well mixed. Then, the solution in beaker A was slowly added to beaker B and stirred vigorously to produce a transparent sticky gel. The sealed sol was placed in the beaker and placed in the shade for 24 h to form a soft elastic solid gel. The gel was removed from the sealing film and dried at 100 • C for 24 h in an electric drying oven (SY-101BS, Tianjin, China), and transparent granular crystals were obtained. After grinding, the powder was placed in a crucible and calcined at 700 • C in a muffle furnace (KSL-1100X, Hefei, China). After calcination, mixed-crystal structure TiO 2 (Mc-TiO 2 ) was obtained through a standard sieve (Model Φ200).

Preparation of Eu-Doped ZIF-8
As weighed by electronic balance (SQP, Beijing, China), 477.8 mg zinc nitrate hexahydrate, 120 mg 2-methylimidazole and a certain mass of europium nitrate hexahydrate were added into 36 mL N, N-dimethylformamide (DMF). The sample was fully dissolved and evenly distributed by an ultrasonic cleaner (KQ-300DE, Kunshan, China) for 20 min at room temperature. The mixed solution of zinc nitrate hexahydrate, 2-methylimidazole and europium nitrate hexahydrate was placed in the 100-mL polytetrafluoroethylene (PTFE) tank of a stainless-steel autoclave, heated to 140 • C at 5 • C/min in an electric drying oven (SY-101BS, Tianjin, China), kept for 24 h and then reduced to room temperature at a rate of 0.4 • C/min. The PTFE liner was removed and the yellow solid on the bottom and inner wall was scraped off and then washed and centrifuged with DMF. The final product was dried for 5 h at 60 • C in a vacuum drying oven (DZ-1BCII, Tianjin, China) and ground into powder to obtain Eu-doped ZIF-8 (ZIF-8(Eu)). As weighed by electronic balance (SQP, Beijing, China), 477.8 mg zinc nitrate hexahydrate, 120 mg 2-methylimidazole and a certain mass of europium nitrate hexahydrate were added into 36 mL N, N-dimethylformamide (DMF), and 0.2 g of Mc-TiO 2 was added. The sample was fully dissolved and evenly distributed by an ultrasonic cleaner (KQ-300DE, Kunshan, China) for 20 min at room temperature. The mixed solution of zinc nitrate hexahydrate, 2-methylimidazole, europium nitrate hexahydrate and Mc-TiO 2 was placed in a 100 mL stainless-steel autoclave, heated to 140 • C at 5 • C/min in an electric drying oven (SY-101BS, Tianjin, China), kept for 24 h and then reduced to room temperature at a rate of 0.4 • C/min. The PTFE inner tank of the stainless-steel autoclave was removed. The yellow solid was scraped off the bottom and inner wall and then washed and centrifuged with DMF. The final product was dried at 60 • C in a vacuum drying oven (DZ-1BCII, Tianjin, China) for 5 h and ground into powder. The amount of Eu doping in ZIF-8 is determined by the molar ratio of Eu to Zn.

Evaluation of Photocatalytic Activity
At room temperature, a certain amount of ZIF-8(Eu)@Mc-TiO 2 was added to 100 mL of a certain concentration of basic fuchsin solution. At first, the mixture was kept in darkness for 30 min in order to reach an adsorption-desorption balance between the photocatalyst and pollutant. The mixture was then transferred to a BL-GHX-V photocatalytic reactor and irradiated with a 550 W mercury lamp under air stirring. Subsequently, 5 mL of reaction solution was taken into the centrifuge tube every 20 min and centrifuged at 8000 rpm to remove the photocatalyst. The basic fuchsin solution concentration of the supernatant was determined by measuring the absorbance of the solution with a TU-1901 ultraviolet-visible spectrophotometer, and then the degradation rate was calculated by the absorbance at the maximum absorption wavelength. As shown in Figure S1 (in Supplementary Information), the maximum absorption wavelength is 543 nm. The degradation rate of the basic fuchsin was calculated as follows [26,27]: where η is degradation rate, and A 0 and A t are the absorbance before and after the solution was illuminated, respectively.

Characterization
The physicochemical properties of ZIF-8(Eu)@Mc-TiO 2 were observed with different characterisation techniques. The specific surface area, pore structure and pore size of ZIF-8(Eu)@Mc-TiO 2 were tested using V-Sorb 2800TP specific surface area and pore size analyser produced by Gold APP Instruments Corporation. Using an X-ray power diffractometer (XRD-700S) with Kα radiation in the 2θ range (5 • -90 • ), X-ray diffraction (XRD) analyses of the ZIF-8, ZIF-8(Eu), TiO 2 and ZIF-8(Eu)@Mc-TiO 2 were performed, running at 40 kV and 100 mA. Scanning electron microscopy (SEM) of the ZIF-8(Eu)@Mc-TiO 2 was performed using FEIQuanta650. The distribution of elements and the proportion of elements in the sample were analysed by energy-dispersive X-ray spectroscopy (EDX), and then the element composition of the sample was determined. Meanwhile, transmission electron microscopy (TEM) was performed using JEM-2100F (Tokyo, Japan) to determine the morphologies and structures of ZIF-8(Eu)@Mc-TiO 2 . TU-1950 dual-beam ultravioletvisible spectrophotometry (UV-Vis) was performed to measure and depict the spectra of different powder samples (200-800 nm). The change in the light-response range before and after doping was analysed by fitting, and the spectral absorption threshold was determined. The AXIS-ULTRA DLD X-ray photoelectron spectrometer produced by Kratos company in UK was used for X-ray photoelectron spectroscopy (XPS) analysis. The binding energy of C1s (284.6 eV) was used to calibrate the binding energy.

Crystal Structure Analysis of Photocatalyst
According to the diffraction angle corresponding to each diffraction peak in Figure 1a, compared with the standard diffraction cards (JCPDS No.21-1272 and JCPDS No.21-1276), it is found that different crystal forms and diffraction peak intensities appear after calcination at different temperatures. When the temperature range is 350-500 • C, the sample is anatase TiO 2 with diffraction angles of (2θ) 25.21 • , 37.82 • , 47.9 • and 62.56 • belonging to the (101), (004), (200) and (204) crystal planes of anatase type, respectively [28]. As shown in Table S1, with the increase of temperature, the crystal size increases and the diffraction peak intensity of the main peak 25.21 • also changes.It can be seen from Figure 1a that, when the temperature is 600-800 • C, the diffraction angles (2θ) are 27.4 • , 36.0 • , 41.56 • and 54.26 • , which correspond to the (110), (101), (111) and (211) crystal planes of rutile type, respectively, thus proving the presence of the rutile type [29]. The mixed-crystal structure appears at 600 • C, and especially at 700 • C, which belongs to anatase and rutile crystal. When the temperature reaches 800 • C, the main peak of anatase disappears, but the small peak of anatase still remains. The mixed-crystal structure is particularly obvious at 700 • C, but, at 600 • C and 800 • C, the mixed-crystal structure is not obvious and the hybrid degree of crystal forms is low. Therefore, the temperature used to calculate the proportion of different crystal forms of the mixed-crystal structure is 700 • C. The rutile type and anatase type occupy 48.38% and 51.62% of the crystal, respectively, at 700 • C.
1a, compared with the standard diffraction cards (JCPDS No.21-1272 and JCPDS No.21-1276), it is found that different crystal forms and diffraction peak intensities appear after calcination at different temperatures. When the temperature range is 350-500 °C, the sample is anatase TiO2 with diffraction angles of (2θ) 25.21°, 37.82°, 47.9° and 62.56° belonging to the (101), (004), (200) and (204) crystal planes of anatase type, respectively [28]. As shown in Table S1, with the increase of temperature, the crystal size increases and the diffraction peak intensity of the main peak 25.21° also changes.It can be seen from Figure  1a that, when the temperature is 600-800 °C, the diffraction angles (2θ) are 27.4°, 36.0°, 41.56° and 54.26°, which correspond to the (110), (101), (111) and (211) crystal planes of rutile type, respectively, thus proving the presence of the rutile type [29]. The mixed-crystal structure appears at 600 °C, and especially at 700 °C, which belongs to anatase and rutile crystal. When the temperature reaches 800 °C, the main peak of anatase disappears, but the small peak of anatase still remains. The mixed-crystal structure is particularly obvious at 700 °C, but, at 600 °C and 800 °C, the mixed-crystal structure is not obvious and the hybrid degree of crystal forms is low. Therefore, the temperature used to calculate the proportion of different crystal forms of the mixed-crystal structure is 700 °C. The rutile type and anatase type occupy 48.38% and 51.62% of the crystal, respectively, at 700 °C.
As shown by the black line in Figure 1b

Morphology Analysis
The morphology of ZIF-8 and ZIF-8(5%Eu)@Mc-TiO 2 was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Figure 2a shows that bare ZIF-8 with a smooth surface and a sharp angular appearance presents a rhombic

Morphology Analysis
The morphology of ZIF-8 and ZIF-8(5%Eu)@Mc-TiO2 was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Figure 2a shows that bare ZIF-8 with a smooth surface and a sharp angular appearance presents a rhombic dodecahedron shape. Figure 2b-d shows that ZIF-8(5%Eu)@Mc-TiO2 is distributed in layers and blocks. As shown in Figure 2e-f, ZIF-8(5%Eu) is uniformly grown on the surface of Mc-TiO2. The formation of the ZIF-8(5%Eu)@Mc-TiO2 composite attenuates the agglomeration of TiO2 and also improves the catalytic ability.

Element Analysis
The elemental composition of the ZIF-8(Eu)@Mc-TiO2 micron composite was detected by energy-dispersive X-ray spectroscopy (EDX) mapping. As shown in Figure 3a, the ZIF-8 are uniformly grown on the surface of TiO2, which indicates that the ZIF-8 successfully coated TiO2. The formation of the ZIF-8(Eu)@Mc-TiO2 micron composite greatly attenuates the agglomeration of TiO2 and also improves the catalytic ability. As shown in Figure 3a, there are five elements that are dispersed on the surface of the material that could also be seen from Figure 3b, which are: oxygen, titanium, zinc, europium and nitrogen on the surface of the ZIF-8(Eu)@Mc-TiO2. The red, blue, green, cyan, and purple colours are the elemental distributions of O, Ti, Eu, Zn and N, respectively. Figure 3c shows the mapping of every single element. As shown in the O and Ti mapping, the distributions of O and Ti are similar. This demonstrates that Ti-O is effectively combined into TiO2, which is verified by XRD. The Eu and Zn mapping also shows the distribution of Eu, which is the same as that of Zn, indicating that Eu is doped into ZIF-8. A comparison of the mapping of Ti and Zn shows that their distributions in the composite are different and overlap. This is because the distribution of Mc-TiO2 in the composite is uneven. Some Mc-TiO2 agglomerates and ZIF-8(Eu) do not completely cover Mc-TiO2. Figure 4 shows the spectra using the X-ray photoelectron spectroscopy (XPS) technique to analyse the valence state of various elements in hybrid. It can be seen from Figure  4a that nitrogen, titanium, oxygen, zinc, europium and other elements are detected in the composite. Figure 4b is the XPS diagram of N in the composite, which belongs to ZIF-8, and there are three peaks at 398.7 eV, 399.5 eV and 400.5 eV corresponding to the pyridine-

Element Analysis
The elemental composition of the ZIF-8(Eu)@Mc-TiO 2 micron composite was detected by energy-dispersive X-ray spectroscopy (EDX) mapping. As shown in Figure 3a, the ZIF-8 are uniformly grown on the surface of TiO2, which indicates that the ZIF-8 successfully coated TiO 2 . The formation of the ZIF-8(Eu)@Mc-TiO 2 micron composite greatly attenuates the agglomeration of TiO 2 and also improves the catalytic ability. As shown in Figure 3a, there are five elements that are dispersed on the surface of the material that could also be seen from Figure 3b, which are: oxygen, titanium, zinc, europium and nitrogen on the surface of the ZIF-8(Eu)@Mc-TiO 2 . The red, blue, green, cyan, and purple colours are the elemental distributions of O, Ti, Eu, Zn and N, respectively. Figure 3c shows the mapping of every single element. As shown in the O and Ti mapping, the distributions of O and Ti are similar. This demonstrates that Ti-O is effectively combined into TiO 2 , which is verified by XRD. The Eu and Zn mapping also shows the distribution of Eu, which is the same as that of Zn, indicating that Eu is doped into ZIF-8. A comparison of the mapping of Ti and Zn shows that their distributions in the composite are different and overlap. This is because the distribution of Mc-TiO 2 in the composite is uneven. Some Mc-TiO 2 agglomerates and ZIF-8(Eu) do not completely cover Mc-TiO 2 . Figure 4 shows the spectra using the X-ray photoelectron spectroscopy (XPS) technique to analyse the valence state of various elements in hybrid. It can be seen from Figure 4a that nitrogen, titanium, oxygen, zinc, europium and other elements are detected in the composite. Figure 4b is the XPS diagram of N in the composite, which belongs to ZIF-8, and there are three peaks at 398.7 eV, 399.5 eV and 400.5 eV corresponding to the pyridinetype, pyrrole-type and graphite-type nitrogen of the N1s peak. Pyridine-type nitrogen atoms replace the carbon atoms in the six-member ring, and pyrrole-type nitrogen atoms are located in the five-member ring [31]. Pyridine-type and pyrrole-type nitrogen can enhance the adsorption performance of ZIF-8 [32]. The XPS spectrum of Ti 2p from the ZIF-8(Eu)@Mc-TiO 2 composite displays two peaks at 458.09 eV and 464.87 eV, which correspond to the binding energies of Ti 2p 1/2 and Ti 2p 3/2 , respectively, in Figure 4d. This indicates the presence of the oxidation state Ti4þ in the ZIF-8(Eu)@TiO 2 composite. Compared to the standard TiO 2 sample, the Ti 2p 1/2 and Ti 2p 3/2 binding energy values of the ZIF-8(Eu)@TiO 2 composite become larger, indicating that the electrons in the TiO 2 are transferred to ZIF-8; this may be due to the fact that the doping of Eu causes a change in the chemical environment around the Ti atom of the electron cloud, finally changing the electron binding energy. This novel structure might induce charge transfer, thereby promoting photoelectron hole separation. Figure 4c shows the XPS of oxygen in the composite. Due to the fact that the molecular formula of ZIF-8 is C 8 H 10 N 4 Zn, the oxygen is considered to have come from the oxygen atoms in TiO 2 . After peak fitting, it is found that the diffraction peaks appear at 529.45 eV and 531.5 eV. These correspond to lattice oxygen and surface adsorbed oxygen, respectively. As can be seen from Figure 4e, the Zn 2p 3/2 and Zn 2p 1/2 binding energies of the composite are 1021.9 eV and 1044.97 eV, respectively [33]. It is proven that Zn exists in the composite in the form of a +2 valence. Figure 4f is the XPS peak fitting diagram of Eu, where 1134.55 eV and 1164.35 correspond to Eu 3d 5/2 and Eu 3d 3/2 , indicating that doped Eu mainly exists in the form of a +3 valence. In ZIF-8(Eu)@Mc-TiO 2 , the valence of each element did not change. type, pyrrole-type and graphite-type nitrogen of the N1s peak. Pyridine-type nitrogen atoms replace the carbon atoms in the six-member ring, and pyrrole-type nitrogen atoms are located in the five-member ring [31]. Pyridine-type and pyrrole-type nitrogen can enhance the adsorption performance of ZIF-8 [32]. The XPS spectrum of Ti 2p from the ZIF-8(Eu)@Mc-TiO2 composite displays two peaks at 458.09 eV and 464.87 eV, which correspond to the binding energies of Ti 2p1/2 and Ti 2p3/2, respectively, in Figure 4d. This indicates the presence of the oxidation state Ti4þ in the ZIF-8(Eu)@TiO2 composite. Compared to the standard TiO2 sample, the Ti 2p1/2 and Ti 2p3/2 binding energy values of the ZIF-8(Eu)@TiO2 composite become larger, indicating that the electrons in the TiO2 are transferred to ZIF-8; this may be due to the fact that the doping of Eu causes a change in the chemical environment around the Ti atom of the electron cloud, finally changing the electron binding energy. This novel structure might induce charge transfer, thereby promoting photoelectron hole separation. Figure 4c shows the XPS of oxygen in the composite. Due to the fact that the molecular formula of ZIF-8 is C8H10N4Zn, the oxygen is considered to have come from the oxygen atoms in TiO2. After peak fitting, it is found that the diffraction peaks appear at 529.45 eV and 531.5 eV. These correspond to lattice oxygen and surface adsorbed oxygen, respectively. As can be seen from Figure 4e, the Zn 2p3/2 and Zn 2p1/2 binding energies of the composite are 1021.9 eV and 1044.97 eV, respectively [33]. It is proven that Zn exists in the composite in the form of a +2 valence. Figure 4f is Figure 5 is the N2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO2. It can be seen from Figure 5 that the N2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO2 is a type-IV IUPAC curve, and that there is single-layer adsorption of capillary condensation. When P/P0 is between 0.1 and 1.0, there is a retention loop and capillary condensation [34]. The retention loop is H4-type. It can be seen from Table 1 that the Brunauer-Emmett-Teller (BET) specific surface area, total pore volume (P/P0 = 0.99) and average pore diameter of ZIF-8(Eu)@Mc-TiO2 are 159.23 m 2 /g, 0.0808 cm 3 /g and 2.0305 nm, respectively; the average pore diameter is in the mesoporous range.   Figure 5 is the N 2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO 2 . It can be seen from Figure 5 that the N 2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO 2 is a type-IV IUPAC curve, and that there is single-layer adsorption of capillary condensation. When P/P 0 is between 0.1 and 1.0, there is a retention loop and capillary condensation [34]. The retention loop is H4-type. It can be seen from Table 1 that the Brunauer-Emmett-Teller (BET) specific surface area, total pore volume (P/P 0 = 0.99) and average pore diameter of ZIF-8(Eu)@Mc-TiO 2 are 159.23 m 2 /g, 0.0808 cm 3 /g and 2.0305 nm, respectively; the average pore diameter is in the mesoporous range.   Figure 5 is the N2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO2. It can be seen from Figure 5 that the N2 adsorption-desorption curve of ZIF-8(Eu)@Mc-TiO2 is a type-IV IUPAC curve, and that there is single-layer adsorption of capillary condensation. When P/P0 is between 0.1 and 1.0, there is a retention loop and capillary condensation [34]. The retention loop is H4-type. It can be seen from Table 1 that the Brunauer-Emmett-Teller (BET) specific surface area, total pore volume (P/P0 = 0.99) and average pore diameter of ZIF-8(Eu)@Mc-TiO2 are 159.23 m 2 /g, 0.0808 cm 3 /g and 2.0305 nm, respectively; the average pore diameter is in the mesoporous range.

Analysis of UV-Vis Diffuse Reflectance Spectroscopy (UV-Vis DRS)
The band gaps of anatase and rutile TiO 2 are 3.2 eV and 3.0 eV, respectively. When irradiated by ultraviolet light, photogenerated electrons will transition from the valence band to the conduction band. At this time, the light energy is converted into electron energy, so that the electron can cross the forbidden band and the photogenerated electron can be transferred to form the photogenerated electron-hole pair [35]. Figure 6a,b shows that ZIF-8 is doped with different amounts of the Eu composite Mc-TiO 2 , where (b) is the enlarged shadow of (a). Figure 6c,d show the band gap of the above materials, where (d) shows the enlarged shadow of (c). Table 2 lists the band gap values of the materials. It can be seen from Figure 6a that, with the doping of EuNO 3 ·6H 2 O, the photoresponse range increases and the UV diffuse reflectance spectrum curve is red-shifted, which causes the photoresponse range to increase. As can be seen from Table 2, the band gaps of ZIF-8@Mc-TiO 2 and ZIF-8(Eu)@Mc-TiO 2 have been reduced by different degrees because ZIF-8 contains light-absorbing organic chromophores and photo-excited semiconductor metal clusters [36]. The charge-transfer interaction between organic groups as donors and Zn 4+ ions as acceptors is longer than that of organic and inorganic groups. Organic molecules can be used as a photon antenna to inject metal quantum dots through energy transfer for photosensitisation in order to improve the light-response range [37].

Analysis of UV-Vis Diffuse Reflectance Spectroscopy (UV-Vis DRS)
The band gaps of anatase and rutile TiO2 are 3.2 eV and 3.0 eV, respectively. When irradiated by ultraviolet light, photogenerated electrons will transition from the valence band to the conduction band. At this time, the light energy is converted into electron energy, so that the electron can cross the forbidden band and the photogenerated electron can be transferred to form the photogenerated electron-hole pair [35]. Figure 6a,b shows that ZIF-8 is doped with different amounts of the Eu composite Mc-TiO2, where (b) is the enlarged shadow of (a). Figure 6c,d show the band gap of the above materials, where (d) shows the enlarged shadow of (c). Table 2 lists the band gap values of the materials. It can be seen from Figure 6a that, with the doping of EuNO3·6H2O, the photoresponse range increases and the UV diffuse reflectance spectrum curve is red-shifted, which causes the photoresponse range to increase. As can be seen from Table 2, the band gaps of ZIF-8@Mc-TiO2 and ZIF-8(Eu)@Mc-TiO2 have been reduced by different degrees because ZIF-8 contains light-absorbing organic chromophores and photo-excited semiconductor metal clusters [36]. The charge-transfer interaction between organic groups as donors and Zn 4+ ions as acceptors is longer than that of organic and inorganic groups. Organic molecules can be used as a photon antenna to inject metal quantum dots through energy transfer for photosensitisation in order to improve the light-response range [37].   A suitable Eu doping amount plays an important role in exerting the catalytic ability of the ZIF-8(Eu)@Mc-TiO 2 photocatalyst. Therefore, we conducted an experiment in which Eu was doped from 0% to 10% in order to determine the appropriate amount of Eu. It can be seen from Figure 7a that the catalytic efficiency is the highest when the Eu doping amount is 5%. The degradation efficiency can reach 99% under UV irradiation for 1 h. From the overall trend of photocatalytic efficiency, the photocatalytic efficiency of 5% Eudoped materials is better than that of other materials. It is possible that the TiO 2 sample at 700 • C has two crystal forms. The combination of the two crystal forms is equivalent to the combination of two semiconductors, which causes the transfer of photogenerated electrons and holes, inhibits the combination of photogenerated electrons and holes and produces more free radicals, thus improving the photocatalytic efficiency. In addition, Eu doping increases the active sites on the surface of the material. When Eu doping is excessive, the pore structure of ZIF-8 will be blocked, the specific surface area of ZIF-8 will be decreased, the adsorption performance will be reduced and the photocatalytic performance of ZIF-8 will be reduced [38].  A suitable Eu doping amount plays an important role in exerting the catalytic ability of the ZIF-8(Eu)@Mc-TiO2 photocatalyst. Therefore, we conducted an experiment in which Eu was doped from 0% to 10% in order to determine the appropriate amount of Eu. It can be seen from Figure 7a that the catalytic efficiency is the highest when the Eu doping amount is 5%. The degradation efficiency can reach 99% under UV irradiation for 1 h. From the overall trend of photocatalytic efficiency, the photocatalytic efficiency of 5% Eudoped materials is better than that of other materials. It is possible that the TiO2 sample at 700 °C has two crystal forms. The combination of the two crystal forms is equivalent to the combination of two semiconductors, which causes the transfer of photogenerated electrons and holes, inhibits the combination of photogenerated electrons and holes and produces more free radicals, thus improving the photocatalytic efficiency. In addition, Eu doping increases the active sites on the surface of the material. When Eu doping is excessive, the pore structure of ZIF-8 will be blocked, the specific surface area of ZIF-8 will be decreased, the adsorption performance will be reduced and the photocatalytic performance of ZIF-8 will be reduced [38].  The catalytic conditions of ZIF-8(Eu)@Mc-TiO 2 are the same as those of Mc-TiO 2 , whereas the catalytic efficiency of ZIF-8(Eu)@Mc-TiO 2 is higher than that of Mc-TiO 2 . ZIF-8 with 5% Eu doping has an especially greater catalytic efficiency, which is mainly due to the increase in the specific surface area and the introduction of more reaction sites. The increase in the specific surface area solves the problem of insufficient reaction sites in Mc-TiO 2 . ZIF-8 provides a large number of reaction sites for the photocatalytic reaction and improves the photocatalytic efficiency [39]. At the same time, with the addition of Eu, the photoresponse range increases by varying degrees, which increases the utilisation of light and improves the photocatalytic efficiency [40]. Figure 7b shows the effect of the basic fuchsin solution concentration on the catalytic efficiency. It can be seen from Figure 7b that, with an increase in the solution concentration from 20 mg/L to 50 mg/L, the catalytic efficiency first increases and then decreases, and the catalytic efficiency of the basic fuchsin solution at 30 mg/L is the highest. Due to the presence of photogenerated carriers on the surface of the composite, the 20 mg/L basic fuchsin solution cannot make full use of the reaction sites [41]. When the concentration reaches 30 mg/L, the reaction sites are fully utilised and the photocatalytic efficiency is improved. When the concentration of the solution increases, the light-penetration ability decreases, resulting in decreases in the light response, photogenerated carriers and photocatalytic efficiency.

Effect of Basic Fuchsin Concentration for Photocatalytic Efficiency
3.6.3. Effect of Dosage of ZIF-8(Eu)@Mc-TiO 2 for Photocatalytic Efficiency Figure 7c shows the effect of the catalyst dosage on the catalytic efficiency, where it can be seen that the photocatalytic efficiency increases when increasing the catalyst dosage from 10 mg to 50 mg, and that there is a positive correlation between the catalyst dosage and photocatalytic efficiency. It is possible that the specific surface area and reaction sites of the materials are improved with the increase in the amount of the catalyst. Under certain other conditions, as the amount of catalyst increases, the amount of photogenerated electron holes is increased, and enough superoxide radicals and hydroxyl radicals are produced to participate in the degradation reaction [42].

Reuse
In order to investigate the stability and reusability of ZIF-8(Eu)@Mc-TiO 2 , four cycles of photodegradation were performed under the same conditions. After each photodegradation experiment, ZIF-8(Eu)@Mc-TiO 2 was collected, washed with anhydrous alcohol and deionised water and dried in a vacuum oven at 100 • C; then, the same sample was subjected to the next photodegradation experiment. Figure 7d shows the stability and reusability results of the ZIF-8(Eu)@Mc-TiO 2 composite. The degradation rate of ZIF-8(Eu)@Mc-TiO 2 decreases slightly because of the unavoidable loss during the recovery process. In the four cycles of the photodegradation experiment, the catalysts maintained excellent degradation activity. The removal rate of basic fuchsin dropped from 93.89% in the first test to 90.84% in the fifth test. This result demonstrates that ZIF-8(Eu)@Mc-TiO 2 has excellent stability and reusability, and that the internal interactions of the composite allow it to maintain its original high efficiency. As shown in Table 3, the degradation rate of the ZIF-8(Eu)@Mc-TiO 2 composite for basic fuchsin was higher than that of other materials. Table 3. ZIF-8(Eu)@Mc-TiO 2 -specific surface area and pore size values.

Conclusions
In this paper, TiO 2 (Mc-TiO 2 ) with a mixed-crystal structure of anatase and rutile types was prepared by a sol-gel method at a calcination temperature of 700 • C. ZIF-8 doped with Eu was compounded with Mc-TiO 2 using the solvothermal method to obtain ZIF-8(Eu)@Mc-TiO 2 . XRD, SEM, TEM, XPS, UV-Vis DRS, BET specific surface area analysis and photocatalytic experiments were carried out. The results show that the specific surface area and the light-response range of the Mc-TiO 2 composite ZIF-8 are increased. After UV irradiation for 1 h, 20 mg of ZIF-8(Eu)@Mc-TiO 2 catalysed 100 mL of 30 mg/L basic fuchsin solution at a degradation rate of up to 99%, demonstrating an excellent photocatalytic effect. In addition, the catalytic efficiency was 90.84% after four cycles. All of the results demonstrate that ZIF-8(Eu)@Mc-TiO 2 is an efficient photocatalytic material for the degradation of organic dyes.