Thermal Hydraulic Performance in a Solar Air Heater Channel with Multi V-Type Perforated Baffles

This article presents heat transfer and fluid flow characteristics in a solar air heater (SAH) channel with multi V-type perforated baffles. The flow passage has an aspect ratio of 10. The relative baffle height, relative pitch, relative baffle hole position, flow attack angle, and baffle open area ratio are 0.6, 8.0, 0.42, 60 ̋, and 12%, respectively. The Reynolds numbers considered in the study was in the range of 3000–10,000. The re-normalization group (RNG) k-ε turbulence model has been used for numerical analysis, and the optimum relative baffle width has been investigated considering relative baffle widths of 1.0–7.0.The numerical results are in good agreement with the experimental data for the range considered in the study. Multi V-type perforated baffles are shown to have better thermal performance as compared to other baffle shapes in a rectangular passage. The overall thermal hydraulic performance shows the maximum value at the relative baffle width of 5.0.


Introduction
Solar energy is one of the renewable and environment-friendly energy sources which can be used in our daily lives without imposing negative effects on the environment.It is generally used for a variety of engineering applications, among the generation of electric power, heating, cooking, and other applications.The solar air heater (SAH) is very simple and commonly used to heat air, and requires no maintenance [1].However, the thermal performance of conventional SAH has been observed to be low because of the low Nusselt number from the heated plate to the fluid.The local heat transfer between the heated wall of SAH and flowing air can be improved by either (1) increasing the heat transfer surface area by means of extended and ribbed surfaces without enhancing the heat transfer rate; or (2) increasing the local heat transfer by means of the vortex generator in the form of baffles roughness on the absorber surface [2,3].The roughness on the absorber plate can be introduced by various techniques casting, forming, welding ribs, baffles, and/or fixing thin circular wires.The use of baffles roughness on the underside of the heated wall can substantially enhance the local heat transfer of the SAH due to the rise in convective heat transfer rate from the plate to air.
Surface roughness is one of the first techniques to be considered as a means of augmenting forced convection heat transfer.In order to attain a higher convective heat transfer rate it is desirable that the flow at the heat transfer surface is turbulent [1][2][3].However, the turbulence created in the core can increase the fan power exorbitantly.It is, therefore, desirable that the turbulence be created very close to the heat transfer surface, i.e., in the laminar sub-layer only, where the heat exchange takes place.However, as pointed out above, it is necessary that while creating turbulence to break the laminar sublayer, the core flow is not disturbed so as to avoid excessive losses.This can be achieved by using baffles roughness with roughness height being such that it does not project into the core but is of the Tamna et al. [22] experimentally and numerically investigated the thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 3.16 and 3.56 times were reported over a smooth rectangular channel.

2
V-shaped baffles (Khanoknaiyakarn et al. [7]) e/H = 0.2-0.4,P/e = 3-8, Re = 5000-25,000 Respective Nuave and fave augmentations of 4.05 and 4.32 times were reported over a smooth rectangular channel.These studies have shown that V-shaped baffles perform better than angled baffles.Respective Nuave and fave augmentations of 3.87 and 4.12 times were reported over a smooth rectangular channel.
2 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 3.16 and 3.56 times were reported over a smooth rectangular channel.

2
V-shaped baffles (Khanoknaiyakarn et al. [7]) e/H = 0.2-0.4,P/e = 3-8, Re = 5000-25,000 Respective Nuave and fave augmentations of 4.05 and 4.32 times were reported over a smooth rectangular channel.These studies have shown that V-shaped baffles perform better than angled baffles.Respective Nuave and fave augmentations of 3.87 and 4.12 times were reported over a smooth rectangular channel.
V-shaped baffles (Khanoknaiyakarn et al. [7]) e/H = 0.2-0.4,P/e = 3-8, Re = 5000-25,000 Respective Nu ave and f ave augmentations of 4.05 and 4.32 times were reported over a smooth rectangular channel.These studies have shown that V-shaped baffles perform better than angled baffles. 3 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.

Perforated baffles (Karwa and
Maheshwari [11]) Respective Nu ave and f ave augmentations of 3.87 and 4.12 times were reported over a smooth rectangular channel. 4 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.
Transverse perforated block baffles (Shin and Kwak [12]) e/D = 1.0,Wc/H = 7.5, Re = 20,000-40,000 Respective Nu ave and f ave augmentations of 3.98 and 4.2 times were reported over a smooth rectangular channel. 5 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 4.98 and 5.04 times were reported over a smooth rectangular channel.These studies have shown that V-shaped perforated blocks perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.

Delta shaped baffles (Bekele et al. [14])
e/H = 0.5, ˝Respective Nu ave and f ave augmentations of 3.67 and 3.89 times were reported over a smooth rectangular channel. 6 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 4.98 and 5.04 times were reported over a smooth rectangular channel.These studies have shown that V-shaped perforated blocks perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.Respective Nu ave and f ave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles. 7 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nuave and fave augmentations of 4.78 and 5.12 times were reported over a smooth rectangular channel.V-shaped perforated baffles perform better than angled and simple V-shaped baffles.Respective Nuave and fave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.Respective Nu ave and f ave augmentations of 4.98 and 5.04 times were reported over a smooth rectangular channel.These studies have shown that V-shaped perforated blocks perform better than angled and simple V-shaped baffles. 8 Energies 2016, 9, 564 3 of 18 thermal hydraulic performance of a rectangular passage with a multi V-type blockage fitted to a heated surface for the range of Re values from 4000 to 21,000.Table 1 summarises the experimental investigations of some important baffle arrangements reported by various researchers.Respective Nu ave and f ave augmentations of 6.28 and 6.55 times were reported over a smooth rectangular channel.These studies have shown that multi V-shaped baffles perform better than other baffles.
Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30 ˝inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30 ˝double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.
Table 2. Summary of results from a previous computational fluid dynamics (CFD)-based study using various baffle shapes in an air channel.

S.N. Baffle Shapes Parameter Ranges Principle Findings
1 Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30° inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30° double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.Respective Nu ave and f ave augmentations of 2.98 and 3.14 times were reported over a smooth rectangular channel. 2 Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30° inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30° double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.Angled baffles (Promvonge et al. [24]) e/H = 0.2-0.5, Respective Nu ave and f ave augmentations of 3.45 and 3.67 times were reported over a smooth rectangular channel. 3 Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30° inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30° double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.4 Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30° inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30° double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.Respective Nu ave and f ave augmentations of 4.11 and 4.39 times augmentation in heat transfer and pressure drop were reported over a smooth rectangular channel. 5 Energies 2016, 9, 564 4 of 18 Computational fluid dynamics (CFD) is a numerical approach used to estimate detailed information for the fluid flow and heat transfer characteristics of a roughened rectangular channel.A critical review on heat transfer enhancement in a rectangular channel revealed that most investigations were carried out experimentally.However, only a few investigations are available those are based on CFD approaches [23][24][25][26][27][28][29][30][31][32][33][34].Gawande et al. [23] conducted a numerical study on the effect of the transverse circular vortex type generator in an air channel.It was observed that the performance of the transverse circular vortex type generator in the channel was better than that of the smooth wall channel.Promvonge et al. [24] carried out a three-dimensional CFD analysis of heat transfer and fluid flow characteristics through a 30° inline angled baffle as tabulators in an air channel.Garg et al. [25] numerically investigated the effect of transverse circular vortex generators for roughened air channels.Jedsadaratanachai and Boonloi [26] presented CFD results of flow and heat transfer characteristics in an isothermal square channel with a 30° double V-baffles.It was found that the use of the double V-baffles led to higher heat transfer rates and pressure loss compared to the smooth channel with no baffle.Moreover, the rise of the blockage ratio and reduction of the pitch ratio led to heat transfer rate and pressure loss increases.Yadav et al. [27] conducted a CFD analysis on the overall thermal performance of a SAH with V-perforated downstream blocks attached to the heated wall.Several researchers numerically investigated rib roughened rectangular channels and reported the effects of rib shapes, rib spacing, rib height, rib flow attack angle, and channel aspect ratio on the heat transfer, pressure drop, and thermal performance [28][29][30][31][32][33][34].Table 2 summarises the numerical investigations of some important baffle arrangements reported by various researchers.A literature review shows that the shape of the transverse baffles increases the heat transfer by air separation, reattachment, and creation of vortices upstream and downstream of the baffles, and that the air re-attaches in inter-baffle spaces.Angulations of the transverse baffles improve the heat transfer further on the explanation of movement of vortices on the length of the baffle wall and create secondary jets close to the leading end, which enhancement outcomes in local surface turbulence.
The advantage of V-down baffles is the generation of the two types of secondary stream jets as compared to only one in the case of angled baffles.In this case, the more the secondary stream jets, the higher the heat transfer rate.Further, making a perforation in the angulations blockage is found to increase the heat transfer by breaking and disturbing the secondary stream jets, and developing maximum level of turbulence in the downstream of the baffles.The use of multi V-type pattern baffles across the width of the passage is observed to improve the heat transfer by increasing the number of secondary stream jets more times in case of single type V-pattern baffle.
Recently, Chamoli and Thakur [20] explored the result of V-down perforated baffles on the heat transfer and fluid flow explanation of a rectangular passage.They concluded that the rise in the heat transfer rate attained was credited to the interaction of the secondary stream jets throughout the perforation, reattachment, and mixture with the main flow that creates extra turbulence.It is assumed that multi V-pattern perforated baffles will increase the heat transfer as compared to either single V-down perforated baffles, or baffles without perforated multi V-down baffles.
The purpose of this study is to numerically and experimentally investigate the air stream and heat transfer behaviour of the three-dimensional rectangular channel with rough in the form of multi V-type perforated baffles.In this investigation, the CFD ANSYS Fluent 6.3.26Software (Fluent Inc., Lebanon, NH, USA) has been used to simulate the heat transfer and flow performance with multi V-type perforated baffles on the heated wall.

Description of Computational Model
The rectangular air passage with multi V-down perforated baffles placed on one side of the heated plate is presented in Figures 1 and 2. The rectangular channel had a stream cross-section of (Wc) 300 mm ˆ(H) 30 mm, with an aspect ratio (Wc/H) of 10.0, and consisted of inlet and outlet parts separated by a test section.The hydraulic diameter (D = 4A/P = 2H) was 54.54 mm.The test unit distance end to end of the passage was 1000 mm.The baffle rough can be explained by the data of the width of the rectangular channel (Wc), width of single V-perforated baffles (Wb), height of the baffles (e), height of the channel (H), hole position (O) spacing between baffles (P), size of hole (d), and flow angle of attack (α).These rough parameters have been explained in the form of dimensionless rough parameters, i.e., the relative baffle width (Wc/Wb), relative baffle height (e/H), relative baffle hole position (O/e), relative baffle pitch (P/e), open area ratio (β), and flow angle of attack (α).The blockage open area ratio is distinct as the ratio of the region perforation to the baffle frontal region, given by: The choices for Re and blockage parameters for this study have been listed in Table 3.The functional fluid was air in all of the cases studied.The velocity inlet was estimated at the inlet face of the duct.The air-inlet temperature was stable at 300 K.The average inlet velocities of the stream were calculated using the Re.The inlet velocity of the air ranged between 0.9 m/s and 2.9 m/s.A heat flux, q = 1000 W/m 2 , was provided to the upper face of the collector, in a similar manner to the experimental setup of prior investigations [21,22].The lower wall and the walls on the other sides were thought to be adiabatic.The exit boundary condition was considered to be at atmospheric pressure, i.e., p = 1.013 ˆ10 5 Pa.

Governing Equations
The numerical model for fluid flow and heat transfer in a SAH duct was developed under the following assumptions:

Governing Equations
The numerical model for fluid flow and heat transfer in a SAH duct was developed under the following assumptions:

Governing Equations
The numerical model for fluid flow and heat transfer in a SAH duct was developed under the following assumptions: The flow is steady, fully developed, turbulent, and three-dimensional.The thermal conductivity of the duct wall, absorber plate and roughness material are independent of temperature.
The duct wall, absorber plate, and roughness material are homogeneous and isotropic.The working fluid (air) is assumed to be incompressible for the operating range of SAH since variation in density is much lower.
No-slip boundary condition is assigned to the walls in contact with the fluid in the model.Radiation heat transfer and other heat losses are negligible.
The governing mathematical equations are the conservation of mass, momentum, and energy that can be described as follows [35]: Continuity equation: ∇.pρ.
Momentum equation: Energy equation: where k eff is the effective conductivity (k eff = k + k t ).
The re-normalization group (RNG) k-ε model was used for turbulent flow [35].In this model, the turbulence kinetic energy (k) and its rate of dissipation (ε) are obtained from the following transport equations: The model constants C 1ε and C 2ε in Equation ( 6) are 1.42 and 1.68, respectively.In these equations G k , S, G b , and Y M represent the production of turbulence kinetic energy, the modulus of the mean rate of the strain tensor, the generation of turbulence kinetic energy due to buoyancy for ideal gas, and the contribution of the fluctuating dilatation in compressible turbulence to the overall dissipation rate, respectively.Correspondingly, they are defined by the following equations:

Grid Independency Test
Figure 3 shows a schematic of the grid systems.Five different grid densities (respectively comprising 1789565, 1864345, 1964367, 2154376, and 2374635 cells) are used in order to select the suitable mesh size that adapts with near-wall modelling.The wall distance y + is considered in the choice of the suitable near wall modelling.Figure 4 shows that the grid independence examination graph between the number of grids and the average Nusselt number for different values of (Wc/Wb) when all other baffles parameters were kept constant, and for a smooth wall with the RNG k-ε turbulence model for five dissimilar grid densities of 1789565, 1864345, 1964367, 2154376, and 2374635 cells.It is observed that the relative deviation of the average Nusselt number among the solutions comprising 2154376 and 2374635 cells is less than 2% at Re = 7000.Hence, the mesh with 2154376 cells with a close to wall element spacing y + « 2 has been chosen for all the cases careful herein.
Energies 2016, 9, 564 8 of 18 solutions comprising 2154376 and 2374635 cells is less than 2% at Re = 7000.Hence, the mesh with 2154376 cells with a close to wall element spacing y + ≈ 2 has been chosen for all the cases careful herein.

Selection of Turbulence Model
Previous investigations [29][30][31][32][33][34] indicated that they used different turbulence models for their studies in air flow channels, such as realizable k-ε model, RNG k-ε model, standard k-ε model, standard k-ω, and shear stress transport k-ω model.Therefore, numerical predictions were compared with available experimental data and the RNG k-ε model was selected in this study because it was found to be the better one.The data of Nuave and fave determined from the CFD results (RNG k-ε model) for single V-type perforated baffle and were compared with the values obtained from the correlations described by Equation ( 7) for Nuave and Equation ( 8) for fave.

Selection of Turbulence Model
Previous investigations [29][30][31][32][33][34] indicated that they used different turbulence models for their studies in air flow channels, such as realizable k-ε model, RNG k-ε model, standard k-ε model, standard k-ω, and shear stress transport k-ω model.Therefore, numerical predictions were compared with available experimental data and the RNG k-ε model was selected in this study because it was found to be the better one.The data of Nuave and fave determined from the CFD results (RNG k-ε model) for single V-type perforated baffle and were compared with the values obtained from the correlations described by Equation (7) for Nuave and Equation ( 8) for fave.
The Nuave correlation for the single V-type perforated baffle [20] is shown as follow: The fave correlation for the single V-type perforated baffle [20] is shown as follows: Comparisons of the experimental and numerical values for Nuave and fave as a function of Re are shown in Figure 5.The average deviations of Nuave and fave obtained using the RNG k-ε turbulence

Selection of Turbulence Model
Previous investigations [29][30][31][32][33][34] indicated that they used different turbulence models for their studies in air flow channels, such as realizable k-ε model, RNG k-ε model, standard k-ε model, standard k-ω, and shear stress transport k-ω model.Therefore, numerical predictions were compared with available experimental data and the RNG k-ε model was selected in this study because it was found to be the better one.The data of Nu ave and f ave determined from the CFD results (RNG k-ε model) for single V-type perforated baffle and were compared with the values obtained from the correlations described by Equation (7) for Nu ave and Equation ( 8) for f ave .
The Nu ave correlation for the single V-type perforated baffle [20] is shown as follow: Nu " 0.029 ˆRe 0.7848 ˆpP{eq 0.3007 ˆpe{Hq ´0.6774 ˆβ´0.3571expp´0.254lnpP{eq 2 q ˆexpp´0.4406lnpe{Hq 2 qexpp´0.0863lnpβq 2 q (7) The f ave correlation for the single V-type perforated baffle [20] is shown as follows: f " 0.632 ˆRe ´0.18 ˆpP{eq ´0.16 ˆpe{Hq 1.05 β ´0.13 Comparisons of the experimental and numerical values for Nu ave and f ave as a function of Re are shown in Figure 5.The average deviations of Nu ave and f ave obtained using the RNG k-ε turbulence model are ˘8.34% and ˘9.73%, respectively, from the experimental results [20].

Solution Method
A three-dimensional model of the flow domain used for numerical analysis was built using ANSYS Fluent 6.3.26Software.Grid was generated in GAMBIT Software.Meshed model was then exported to ANSYS Fluent 6.3.26 for analysis.The continuity equation, energy equation, and the Navier-Stokes equations in their steady, incompressible form, along with the associated boundary conditions, were solved using the multipurpose finite volume-based CFD software package, ANSYS Fluent 6.3.26.In the present numerical study, RNG k- turbulence model with 'enhanced wall treatment' was used.In the discretization of governing equations, SIMPLE (semi-implicit method for pressure linked equations) algorithm was used in pressure-velocity coupling as suggested by Kumar and Kim [34].This algorithm was developed by Karmare and Tikekar [29] and is based on a predictor-corrector approach.Double precision pressure-based solver was selected in order to solve the set of equations used.Second order upwind discretization scheme was selected for all the transport equations as suggested by Kumar and Saini [30].Whenever convergence problems were noticed, the solution was started using the first order upwind discretization scheme and continued with the second order upwind scheme.The governing equations for mass and momentum conservation were solved with a segregated approach in steady state, where equations are sequentially solved with implicit linearization.In the present simulation, the convergence criteria between two consecutive iterations was set to be the relative deviation less than 10 −6 for energy equation and less than 10 −3 for the solution in velocity and continuity equation.

Data Reduction
The values of Reynolds number, Nusselt number, average Nusselt number, friction factor and thermal-hydraulic performance have been calculated using the following equations [15,17,[19][20][21][22][23]: The Reynolds number: The heat transfer performance is calculated using the Nu, which can be obtained from:

Solution Method
A three-dimensional model of the flow domain used for numerical analysis was built using ANSYS Fluent 6.3.26Software.Grid was generated in GAMBIT Software.Meshed model was then exported to ANSYS Fluent 6.3.26 for analysis.The continuity equation, energy equation, and the Navier-Stokes equations in their steady, incompressible form, along with the associated boundary conditions, were solved using the multipurpose finite volume-based CFD software package, ANSYS Fluent 6.3.26.In the present numerical study, RNG k-ε turbulence model with 'enhanced wall treatment' was used.In the discretization of governing equations, SIMPLE (semi-implicit method for pressure linked equations) algorithm was used in pressure-velocity coupling as suggested by Kumar and Kim [34].This algorithm was developed by Karmare and Tikekar [29] and is based on a predictor-corrector approach.Double precision pressure-based solver was selected in order to solve the set of equations used.Second order upwind discretization scheme was selected for all the transport equations as suggested by Kumar and Saini [30].Whenever convergence problems were noticed, the solution was started using the first order upwind discretization scheme and continued with the second order upwind scheme.The governing equations for mass and momentum conservation were solved with a segregated approach in steady state, where equations are sequentially solved with implicit linearization.In the present simulation, the convergence criteria between two consecutive iterations was set to be the relative deviation less than 10 ´6 for energy equation and less than 10 ´3 for the solution in velocity and continuity equation.

Data Reduction
The values of Reynolds number, Nusselt number, average Nusselt number, friction factor and thermal-hydraulic performance have been calculated using the following equations [15,17,[19][20][21][22][23]: The Reynolds number: The heat transfer performance is calculated using the Nu, which can be obtained from: The average Nu ave can be obtained from: The f is calculated using the following equation: where ∆p is the pressure drop through the length of the duct, L.
The thermal enhancement factor (η) is defined as the ratio of the heat transfer coefficient of an augmented surface (h) to that of a smooth channel without ribs (h s ) at an equal pumping power.
η " h h s " pNu ave {Nus ave q { p f ave { f s ave q 0.33 (13) where Nu ave and f ave are the average Nusselt number and friction factor for the smooth duct, respectively.

Results and Discussion
The CFD analysis has been performed for a roughened rectangular channel with multi V-down perforated baffles on a heated plate, and the results are discussed in this section.

Heat Transfer and Fluid Flow
The outcome of the Wc/Wb on the Nu ave and f ave for air stream are presented in a rectangular channel.The results have been comparable with those obtained in the case of a smooth wall channel working under similar numerical circumstances.
The results of Nu ave have been shown as a function of Re for the different values of Wc/Wb in Figure 6, and for constant values of the other parameters, such as e/H = 0.6, P/e = 8.0, O/e = 0.42, β = 12%, and α = 60 ˝.It has been seen that the Nu ave increases with an increase in the Wc/Wb, and attains a maximum value matching to a Wc/Wb value of 5.0 in the range of the parameters investigated.In all cases, the presence of a wall with multi V-down perforated baffles produces higher Nu ave compared to the case of a smooth wall, as expected.The V-down perforated baffles can lead to better Nu ave performance because of the secondary stream jets induced by the top part of the baffles.These secondary stream jets have the form of more than one counter rotating vortex, which carry cold air from the middle core region towards the baffle walls.These secondary flow jets interact with the main stream, thereby affecting the flow re-attachment and re-circulation between baffles, and interrupt the boundary layer enlargement downward of the re-attachment regions.
Figure 7 presents the contour map of the turbulent intensity for different Wc/Wb values, while other roughness parameters are maintained constant and equal to e/H = 0.6, P/e = 8.0, β = 12%, O/e = 0.42, α = 60 ˝, and Re = 5000.It can be observed that doubling the value of the width ratio Wc/Wb also increases the number of leading and trailing ends as well as the secondary flow cells, thereby resulting in a considerable enhancement in the heat transfer, as clearly observed in Figure 7.However, the increase in Nu ave continues only up to a Wc/Wb of 5.0.Subsequently, a further increase in the baffle width results in the reduction of the Nu ave.The V-pattern configuration of the baffles induces strong secondary stream jets along the limbs and a higher level of mixing and turbulence when the jets passing from the various perforations re-attach and mix with the main stream.compared to the case of a smooth wall, as expected.The V-down perforated baffles can lead to better Nuave performance because of the secondary stream jets induced by the top part of the baffles.These secondary stream jets have the form of more than one counter rotating vortex, which carry cold air from the middle core region towards the baffle walls.These secondary flow jets interact with the main stream, thereby affecting the flow re-attachment and re-circulation between baffles, and interrupt the boundary layer enlargement downward of the re-attachment regions.Introduction of the perforated multi V-baffles allows the release of the secondary stream jets and the mixing with the main stream through the perforations, as shown in Figure 8. Use of baffle roughness on a heated wall substantially increases the heat transfer from the Introduction of the perforated multi V-baffles allows the release of the secondary stream jets and the mixing with the main stream through the perforations, as shown in Figure 8.
Use of baffle roughness on a heated wall substantially increases the heat transfer from the heated wall of rectangular channels.However, it results in corresponding increases in frictional losses.Figure 9 shows the variation in the f ave with Re for different values of Wc/Wb, while all other rough parameters are maintained constant at e/H = 0.6, P/e = 8.0, O/e = 0.42, β = 12%, and α = 60 ˝.It has been observed from this plot that the f ave decreases with increases in the Re values, for all values of Wc/Wb.It can also be seen that the f ave increases monotonically with increases in Wc/Wb values.The maximum value of the f ave has been observed at a value of Wc/Wb of 7.0.This is due to fact that angulation of the baffles helps in the development of the secondary stream jets.Increasing the value of Wc/Wb would lead to an increased number of secondary stream jets, which in turn increases the value of the Nu ave up to 5.0.Furthermore, increases in Wc/Wb beyond 5.0 could lead to the partition of flow from the top baffle surface, and to a subsequent reduction in Nu ave .However, the values of f ave increase continuously due to the mixing of an increased number of secondary flows after being issued from the perforations and after their re-attachment with the heated surface.For this reason, this mixing increases heat transfer from the plate to air, but also facilitates large pressure drops through the flow across the passage.Introduction of the perforated multi V-baffles allows the release of the secondary stream jets and the mixing with the main stream through the perforations, as shown in Figure 8. Use of baffle roughness on a heated wall substantially increases the heat transfer from the heated wall of rectangular channels.However, it results in corresponding increases in frictional losses.Figure 9

Thermo-Hydraulic Performance
Analysis of the thermal and friction behaviours shows that improvement in thermal performance is, in general, accompanied with a friction penalty owing to a resultant augmentation of the friction factor.Consequently, it is necessary to establish the baffle shapes that will result in the maximal enhancement in heat transfer with the least frictional power penalty.This can be achieved by concurrent thought of thermal as well as hydraulic performances, i.e., the thermo-hydraulic performance parameter, η, which indicates the comparison of the heat transfer enhancement for a roughened channel to a smooth (without rough) channel for the same pumping power requirements, and for fully developed turbulent flows.The following Equation ( 14) represents the thermo-hydraulic performance parameter [31][32][33][34]36,37]: An increased parameter value indicates a relatively more efficient use of the augmentation device, and can be used to evaluate the performance of the number of preparations in order to decide the best one among these.The variation in η is shown in Figure 10 for different values of Wc/Wb.It can be observed that the value of the thermo-hydraulic performance parameter (η) is maximized for a Wc/Wb value of 5.0 at any Re value, considered the current investigation.

Thermo-Hydraulic Performance
Analysis of the thermal and friction behaviours shows that improvement in thermal performance is, in general, accompanied with a friction penalty owing to a resultant augmentation of the friction factor.Consequently, it is necessary to establish the baffle shapes that will result in the maximal enhancement in heat transfer with the least frictional power penalty.This can be achieved by concurrent thought of thermal as well as hydraulic performances, i.e., the thermo-hydraulic performance parameter, η, which indicates the comparison of the heat transfer enhancement for a roughened channel to a smooth (without rough) channel for the same pumping power requirements, and for fully developed turbulent flows.The following Equation ( 14) represents the thermo-hydraulic performance parameter [31][32][33][34]36,37]: η " pNu ave {Nus ave q { p f ave { f s ave q 0.33 (14) An increased parameter value indicates a relatively more efficient use of the augmentation device, and can be used to evaluate the performance of the number of preparations in order to decide the best one among these.The variation in η is shown in Figure 10 for different values of Wc/Wb.It can be observed that the value of the thermo-hydraulic performance parameter (η) is maximized for a Wc/Wb value of 5.0 at any Re value, considered the current investigation.
roughened channel to a smooth (without rough) channel for the same pumping power requirements, and for fully developed turbulent flows.The following Equation ( 14) represents the thermo-hydraulic performance parameter [31][32][33][34]36,37]: An increased parameter value indicates a relatively more efficient use of the augmentation device, and can be used to evaluate the performance of the number of preparations in order to decide the best one among these.The variation in η is shown in Figure 10 for different values of Wc/Wb.It can be observed that the value of the thermo-hydraulic performance parameter (η) is maximized for a Wc/Wb value of 5.0 at any Re value, considered the current investigation.

Experimental Setup Details
A schematic diagram of an experimental setup is shown in Figure 11.The setup comprised a rectangular wooden channel coupled to a centrifugal blower through a circular galvanized iron (GI)

Experimental Setup Details
A schematic diagram of an experimental setup is shown in Figure 11.The setup comprised a rectangular wooden channel coupled to a centrifugal blower through a circular galvanized iron (GI) pipe.The rectangular channel had Wc of 300 mm, H of 30 mm, and Wc/H of 10.It consisted of inlet and exit sections that were interposed by test sections.The upper wall of the test section was an aluminum heated plate that was heated by an electric heater which provided a uniform heat flux over the whole top wall.Air mass flow rate through the SAH was measured with a calibrated orifice meter that was attached to a U-tube manometer.Air flow was regulated with two gate valves that were coupled in the lines.The temperature was calculated at different locations with calibrated 0.3 mm diameter copper constantan thermocouples, which were coupled to a digital micro voltmeter (DMV) to illustrate the temperature.The pressure drop crossways the test section was deliberate with a micro-manometer having least count of 0.001 mm of water.

Uncertainty Analysis
An uncertainty analysis has been carried to estimate the errors involved in experimental data measurement.The uncertainty is estimated based on errors associated with measuring instruments [38].The maximum possible measurement errors in the values of major parameters are given below: Mass flow rate (ma) 2.67%

Uncertainty Analysis
An uncertainty analysis has been carried to estimate the errors involved in experimental data measurement.The uncertainty is estimated based on errors associated with measuring instruments [38].The maximum possible measurement errors in the values of major parameters are given below: Mass flow rate (m a ) 2.67% Reynolds number (Re) 5.87% Heat transfer coefficient (h t ) 6.23% Average Nusselt number (Nu ave ) 5.98% Average friction factor (f ave ) 4.18%

Validation of Computational Fluid Dynamics Results Using Experimental Data
For the validation of the present numerical model, the numerical results (average Nusselt number, average friction factor and thermohydraulic performance) of a rectangular channel with multi V-type perforated baffle attached on a heated plate are compared with experimental results under similar experimental operating conditions.For validation of present CFD outcomes, baffle roughened parameters were selected such as Wc/Wb = 5.0, e/H = 0.6, P/e = 8.0, O/e = 0.42, β = 12%, and α = 60 ˝.Relative baffle width ratio (Wc/Wb) was selected as 5.0 based on the optimal value of this parameter based on the CFD results.Figure 12 shows the comparison of the CFD results with experimental data of the average Nusselt number, average friction factor as a function of the Reynolds number.The average deviations of the average Nusselt numbers, friction factors, and thermohydraulic performance are ˘7.98%,˘9.56%, and ˘8.56%, respectively.The values of η = (Nuave/Nusave)/(fave/fsave) 0.33 of the multi V-shaped perforated baffles have been compared with the values for other baffle shapes in a rectangular channel, as shown in Figure 13.It is seen that the multi V-shaped perforated baffle shape results in the best thermo-hydraulic performance η = (Nuave/Nusave)/(fave/fsave) 0.33 among all the shapes investigated.The values of η = (Nu ave /Nus ave )/(f ave /fs ave ) 0.33 of the multi V-shaped perforated baffles have been compared with the values for other baffle shapes in a rectangular channel, as shown in Figure 13.It is seen that the multi V-shaped perforated baffle shape results in the best thermo-hydraulic performance η = (Nu ave /Nus ave )/(f ave /fs ave ) 0.33 among all the shapes investigated.The values of η = (Nuave/Nusave)/(fave/fsave) 0.33 of the multi V-shaped perforated baffles have bee mpared with the values for other baffle shapes in a rectangular channel, as shown in Figure 13.seen that the multi V-shaped perforated baffle shape results in the best thermo-hydraul rformance η = (Nuave/Nusave)/(fave/fsave) 0.33 among all the shapes investigated.

Conclusions
The heat transfer and pressure drop characteristics have been investigated in multi V-patter rforated baffle attached on one broad wall, which is exposed to uniform heat flux in a rectangula annel.The effects of baffle width ratios on average Nusselt number, average friction factor, an ermal-hydraulic performance have been also studied for Reynolds number in the range o 00-10,000.Multi V-shaped perforated baffles show a considerable enhancement in the hea nsfer rate, and the heat transfer enhancement strongly depends on the relative baffle width rati

Conclusions
The heat transfer and pressure drop characteristics have been investigated in multi V-pattern perforated baffle attached on one broad wall, which is exposed to uniform heat flux in a rectangular channel.The effects of baffle width ratios on average Nusselt number, average friction factor, and thermal-hydraulic performance have been also studied for Reynolds number in the range of 3000-10,000.Multi V-shaped perforated baffles show a considerable enhancement in the heat transfer rate, and the heat transfer enhancement strongly depends on the relative baffle width ratio.The average Nusselt number increases whereas the average friction factor decreases with an increase in the Reynolds number.The values of average Nusselt numbers and friction factors are found to be higher for multi V-shaped perforated baffles compared to those for a rectangular channel without baffles.This is attributed to the change in the fluid flow characteristics due to the baffle roughness that causes generation of secondary flows.The maximum values of average Nusselt number and friction factor are observed for multi V-shaped perforated baffles width ratio of 5.0 and 7.0, respectively.The optimum value of the thermo-hydraulic performance for multi V-shaped perforated baffles in a rectangular channel has been found at the baffle width ratio of 5.0.Multi V-shaped perforated baffles have also been shown to be thermo-hydraulically better in comparison to other baffle shapes in a rectangular channel.The outcomes of 3-D CFD analysis are in good agreement with the experimental data, and thus the current CFD model can be used for the analysis of the new baffle shapes in rectangular channel.

Figure 3 .
Figure 3. Schematic of the grid systems.

Figure 4 .
Figure 4. Variation in average Nusselt number with respect to the number of grids for a width ratio (Wc/Wb = 1.2) and a smooth surface rectangular channel with the Reynolds number of 7000.

Figure 3 .
Figure 3. Schematic of the grid systems.
and 2374635 cells is less than 2% at Re = 7000.Hence, the mesh with 2154376 cells with a close to wall element spacing y + ≈ 2 has been chosen for all the cases careful herein.

Figure 3 .
Figure 3. Schematic of the grid systems.

Figure 4 .
Figure 4. Variation in average Nusselt number with respect to the number of grids for a width ratio (Wc/Wb = 1.2) and a smooth surface rectangular channel with the Reynolds number of 7000.

Figure 4 .
Figure 4. Variation in average Nusselt number with respect to the number of grids for a width ratio (Wc/Wb = 1.2) and a smooth surface rectangular channel with the Reynolds number of 7000.

Figure 5 .
Figure 5.Comparison of experimental results with CFD results of single V-type perforated baffle: (A) Nuave and (B) fave.

Figure 5 .
Figure 5.Comparison of experimental results with CFD results of single V-type perforated baffle: (A) Nu ave and (B) f ave .

Figure 6 .
Figure 6.Variation in the average Nusselt number Nuave with respect to Reynolds number for different Wc/Wb.

Figure 7
Figure 7 presents the contour map of the turbulent intensity for different Wc/Wb values, while other roughness parameters are maintained constant and equal to e/H = 0.6, P/e = 8.0, β = 12%, O/e = 0.42, α = 60°, and Re = 5000.It can be observed that doubling the value of the width ratio Wc/Wb also increases the number of leading and trailing ends as well as the secondary flow cells, thereby resulting in a considerable enhancement in the heat transfer, as clearly observed in Figure 7.However, the increase in Nuave continues only up to a Wc/Wb of 5.0.Subsequently, a further increase in the baffle width results in the reduction of the Nuave.The V-pattern configuration of the baffles induces strong secondary stream jets along the limbs and a higher level of mixing and turbulence when the jets passing from the various perforations re-attach and mix with the main stream.

Figure 6 . 18 Figure 7 .
Figure 6.Variation in the average Nusselt number Nu ave with respect to Reynolds number for different Wc/Wb.Energies 2016, 9, 564 11 of 18
shows the variation in the fave with Re for different values of Wc/Wb, while all other rough parameters are maintained constant at e/H = 0.6, P/e = 8.0, O/e = 0.42, β = 12%, and α = 60°.It has been observed from this plot that the fave decreases with increases in the Re values, for all values of Wc/Wb.It can also be seen that the fave increases monotonically with increases in Wc/Wb values.The maximum value of the fave has been observed at a value of Wc/Wb of 7.0.This is due to fact that angulation of the baffles helps in the development of the secondary stream jets.Increasing the value of Wc/Wb would lead to an increased number of secondary stream jets, which in turn increases the value of the Nuave up to 5.0.Furthermore, increases in Wc/Wb beyond 5.0 could lead to the partition of flow from the top baffle surface, and to a subsequent reduction in Nuave.However, the values of fave increase continuously due to the mixing of an increased number of secondary flows after being issued from the perforations and after their re-attachment with the heated surface.For this reason, this mixing increases heat transfer from the plate to air, but also facilitates large pressure drops through the flow across the passage.

Figure 9 .
Figure 9. Variation of friction factors (f ave ) with respect to the Reynolds number.
rectangular channel had Wc of 300 mm, H of 30 mm, and Wc/H of 10.It consisted of inlet and exit sections that were interposed by test sections.The upper wall of the test section was an aluminum heated plate that was heated by an electric heater which provided a uniform heat flux over the whole top wall.Air mass flow rate through the SAH was measured with a calibrated orifice meter that was attached to a U-tube manometer.Air flow was regulated with two gate valves that were coupled in the lines.The temperature was calculated at different locations with calibrated 0.3 mm diameter copper constantan thermocouples, which were coupled to a digital micro voltmeter (DMV) to illustrate the temperature.The pressure drop crossways the test section was deliberate with a micro-manometer having least count of 0.001 mm of water.

Figure 11 .
Figure 11.Details of experimental setup: (A) line diagram experimental setup; (B) photographic view of multi V-perforated baffle; and (C) photographic view of experimental setup.

Figure 11 .
Figure 11.Details of experimental setup: (A) line diagram experimental setup; (B) photographic view of multi V-perforated baffle; and (C) photographic view of experimental setup.

Figure 13 .
Figure 13.Comparison of various baffle shapes in a rectangular channel.

Figure 13 .
Figure 13.Comparison of various baffle shapes in a rectangular channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 1 .
Previous experimental investigations in various baffle shapes in an air channel.

Table 3 .
Range of operating parameters for CFD analysis.

Table 3 .
Range of operating parameters for CFD analysis.