Dynamic Energy Management of Hybrid Energy Storage Systems with a Hierarchical Structure

In power system control unicontrol with single storage units or centralized control with multiple storage units to meet different level targets is challenging. Considering the charge and discharge characteristics of storage devices, this paper proposes a hierarchical configuration structure of a battery and supercapacitor mixed storage scenario, and develops a convenient control method for accessing various DC loads and can central manage mass batteries in one place. Aiming at the optimal management of large scale battery storage, the paper proposes a three-layer battery hierarchical control structure and the control objects and control circuits are discussed. Simulation studies are used to verify the control effect of the hierarchical storage system and the results show that the strategy can effectively decrease photovoltaic output fluctuation.


Introduction
As the cost is continuously decreasing, photovoltaic (PV) generation has become one of the most important renewable energy sources and is being widely used.Grid-connected solar photovoltaic power plants are being installed globally at a fast pace.However, for present photovoltaic power technologies, the output power depends upon the availability of illumination and therefore may not always be constant.Problems brought by photovoltaics to the security stabilization and control of power grids are progressively appearing [1], especially when high permeability photovoltaics are accessed in a system.Additional regulations and standards are expected to be imposed.
A possible solution for regulating the natural oscillating output power of photovoltaics is to integrate them with an energy storage system [2].Through a reasonable energy storage control strategy, the charge and discharge of energy storage can be controlled dynamically, which will make it possible to balance the energy of power grids and optimize system operation [3,4].Used as an emergency power supply and energy buffer device, energy storage can not only balance photovoltaic output fluctuation, but also improve photovoltaic capacity permeability and utilization level, optimize the power grid economics, and improve the stability of the entire photovoltaic system [5].Reasonable storage configurations and control strategies are therefore of great significance for photovoltaic and energy-storage hybrid systems in high photovoltaic penetration scenarios.
At present, most research on photovoltaic and energy-storage hybrid system focuses on predictive techniques, and control methods for modular converters and voltage regulators [6][7][8][9].Control strategies of different time scales are also taken into consideration [10].Some researchers have studied storage charge and discharge control strategies based on hybrid energy storage.Tummuru proposed a fast acting DC-link voltage-based energy management schemes for a hybrid energy storage system (HES) fed by solar photovoltaic (PV) energy.Using the proposed control schemes, fast DC-link voltage, effective energy management and reduced current stress on batteries are achieved [11].Feng proposed a HES composed of lithium-ion batteries and supercapacitors that can be incorporated in the PV-based system to complement the supply-demand mismatches by using a multimode fuzzy-logic power allocator [12].Ciobotaru proposed a power management strategy of a hybrid energy storage system (HESS) to reduce the required power rating of the supercapacitor bank (SCB) to only one-fifth of the vanadium redox battery (VRB) rating and to avoid the operation of the VRB at low power levels [13].
Based on the aforementioned review of previous works, it can be found that most research only considers the control effect of each storage device or hybrid storage in a centralized structure, and little work has been done to study the configuration pattern of different energy storage systems.Configuring different energy storages reasonably and hierarchical control strategies still need further study.
This paper proposes an energy management strategy based on a hierarchical storage structure.Based on the equivalent circuit models of PV, battery and supercapacitor, the paper introduces a typical distribution network structure with hierarchical storage, and then analyzes the control effect of batteries and supercapacitors.An improved configuration structure is proposed and its control method when some constraint conditions are taken into account is discussed.What's more, to solve the problem brought by centralized management of mass batteries, a three-layer management structure is introduced.Finally, simulation is carried out to verify the control effect.

PV System Modeling
Commonly, PV plants use silicon solar cells, which equivalent circuit is shown in Figure 1 where I ph is the current of a photo-generated current source, D is a non-linear diode, R sh and R s are the internal parallel and series resistance.respectively, I PV is the photovoltaic output current, V PV is the photovoltaic output voltage.The volt-ampere characteristic equation is then: where I s is the diode saturation current, q is a constant (1.602 ˆ10 ´19 C), k is the Boltzmann constant (1.381 ˆ10 ´23 J{K ), T PV is absolute temperature when the photovoltaic works, A is a diode feature fitting coefficient.
Energies 2016, 9, 395 2 of 15 energy storage system (HES) fed by solar photovoltaic (PV) energy.Using the proposed control schemes, fast DC-link voltage, effective energy management and reduced current stress on batteries are achieved [11].Feng proposed a HES composed of lithium-ion batteries and supercapacitors that can be incorporated in the PV-based system to complement the supply-demand mismatches by using a multimode fuzzy-logic power allocator [12].Ciobotaru proposed a power management strategy of a hybrid energy storage system (HESS) to reduce the required power rating of the supercapacitor bank (SCB) to only one-fifth of the vanadium redox battery (VRB) rating and to avoid the operation of the VRB at low power levels [13].
Based on the aforementioned review of previous works, it can be found that most research only considers the control effect of each storage device or hybrid storage in a centralized structure, and little work has been done to study the configuration pattern of different energy storage systems.Configuring different energy storages reasonably and hierarchical control strategies still need further study.
This paper proposes an energy management strategy based on a hierarchical storage structure.Based on the equivalent circuit models of PV, battery and supercapacitor, the paper introduces a typical distribution network structure with hierarchical storage, and then analyzes the control effect of batteries and supercapacitors.An improved configuration structure is proposed and its control method when some constraint conditions are taken into account is discussed.What's more, to solve the problem brought by centralized management of mass batteries, a three-layer management structure is introduced.Finally, simulation is carried out to verify the control effect.

PV System Modeling
Commonly, PV plants use silicon solar cells, which equivalent circuit is shown in Figure 1.
where Iph is the current of a photo-generated current source, D is a non-linear diode, Rsh and Rs are the internal parallel and series resistance.respectively, IPV is the photovoltaic output current, VPV is the photovoltaic output voltage.The volt-ampere characteristic equation is then: where Is is the diode saturation current, q is a constant ( The photogenerated current is a function of light intensity and PV battery temperature, and it can be described as: The photogenerated current is a function of light intensity and PV battery temperature, and it can be described as: Energies 2016, 9, 395 where S is the actual irradiance, S ref is the irradiance under standard conditions, T ref is the absolute temperature when the photovoltaic works under standard conditions, C T is the temperature coefficient, and I ph,ref is the photogenerated current under standard conditions.

Storage Battery Modeling
The storage battery introduces a non-linear model, which uses a simple controlled voltage source in series with a constant resistance, as shown in Figure 2. where S is the actual irradiance, Sref is the irradiance under standard conditions, Tref is the absolute temperature when the photovoltaic works under standard conditions, CT is the temperature coefficient, and Iph,ref is the photogenerated current under standard conditions.

Storage Battery Modeling
The storage battery introduces a non-linear model, which uses a simple controlled voltage source in series with a constant resistance, as shown in Figure 2.
where E is the no-load voltage, E0 is the battery constant voltage, K is the polarisation voltage, Q is the battery capacity, idt  is the actual battery charge, A is the exponential zone amplitude, B is the inverse exponential zone time constant.
This model represents a non-linear voltage which depends solely on the actual battery charge.It means that when the battery is almost completely discharged and no current is flowing, the voltage will be nearly 0. This model yields accurate results and also represents the behaviour of the battery.

Supercapacitor Modeling
The supercapacitor considered in this paper is double-layer capacitor, its equivalent model circuit is shown in Figure 3.This model provides three different time constants to model the different charge transfers, which provides sufficient accuracy to describe the terminal behaviour of the supercapacitor for the desired span of 30 min.
To reflect the voltage dependence of the capacitance, the first branch is modelled as a voltage dependent differential capacitor.The differential capacitor consists of a fixed capacitance Ci0 and a voltage dependent capacitor Ci1 × Vci.A resistor, parallel to the terminals, is added to represent the self-discharge property.The first or immediate branch, with the elements Ri, Ci0 and the voltage dependent capacitance Ci1 in [F/V], dominates the immediate behaviour of the supercapacitor in the time range of seconds in response to a charge action.The second or delayed branch, with parameters Rd and Cd, dominates the behaviour in the range of minutes.Finally, the third or long term branch, with parameters Rl and Cl, determines the behaviour for times longer than 10 min [14].The model assumes the same characteristics for the charge and the discharge cycles.The open voltage source is calculated with a non-linear equation based on the actual SOC of the battery.The controlled voltage source is described as: where E is the no-load voltage, E 0 is the battery constant voltage, K is the polarisation voltage, Q is the battery capacity, idt is the actual battery charge, A is the exponential zone amplitude, B is the inverse exponential zone time constant.This model represents a non-linear voltage which depends solely on the actual battery charge.It means that when the battery is almost completely discharged and no current is flowing, the voltage will be nearly 0. This model yields accurate results and also represents the behaviour of the battery.

Supercapacitor Modeling
The supercapacitor considered in this paper is double-layer capacitor, its equivalent model circuit is shown in Figure 3.This model provides three different time constants to model the different charge transfers, which provides sufficient accuracy to describe the terminal behaviour of the supercapacitor for the desired span of 30 min.
To reflect the voltage dependence of the capacitance, the first branch is modelled as a voltage dependent differential capacitor.The differential capacitor consists of a fixed capacitance C i0 and a voltage dependent capacitor C i1 ˆVci .A resistor, parallel to the terminals, is added to represent the self-discharge property.The first or immediate branch, with the elements R i , C i0 and the voltage dependent capacitance C i1 in [F/V], dominates the immediate behaviour of the supercapacitor in the time range of seconds in response to a charge action.The second or delayed branch, with parameters R d and C d , dominates the behaviour in the range of minutes.Finally, the third or long term branch, with parameters R l and C l , determines the behaviour for times longer than 10 min [14].
Equivalent model circuit for the supercapacitor.

Hierarchical Structure
At present, many different kinds of energy storage devices are known, including batteries, supercapacitors, flywheels, superconducting magnetics and so on, most of which have different charge and discharge characteristics [15,16].The bidirectional energy adjustment ability of energy storage devices make them play an important role in photovoltaic power systems.Compared with the single-technology energy storage system (ESS), a HESS can combine the advantages of each technology used, thus being more suitable for large-scale renewable energy systems.Typical combinations may include a battery and supercapacitor.
However, most storage devices are configured in the same place or just near photovoltaic power generators, so researchers are not very concerned about the configuration method of the battery and supercapacitor.This may lead to complex control circuits and inefficient control processes.A typical distribution network structure with hierarchical storage is shown in Figure 4.In this typical structure, the centralized storage refers to a large-scale energy storage system consisting of mass energy storage devices connected in series or in parallel, that is generally configured in a particular area.The distributed storage refers to small-scale storage devices which are installed throughout the distribution network, and are generally configured in the same or nearby nodes of the photovoltaic system, in order to constitute a combined photovoltaic and storage power-generation system.Centralized storage is mainly used to implement overall coordinated control of distribution networks, while distributed storage takes charge of local power balancing of photovoltaics.
As the control targets of centralized storage and distributed storage are different, it's necessary to select suitable storage devices to fit each target.Storage batteries have characteristics of low

Hierarchical Structure
At present, many different kinds of energy storage devices are known, including batteries, supercapacitors, flywheels, superconducting magnetics and so on, most of which have different charge and discharge characteristics [15,16].The bidirectional energy adjustment ability of energy storage devices make them play an important role in photovoltaic power systems.Compared with the single-technology energy storage system (ESS), a HESS can combine the advantages of each technology used, thus being more suitable for large-scale renewable energy systems.Typical combinations may include a battery and supercapacitor.
However, most storage devices are configured in the same place or just near photovoltaic power generators, so researchers are not very concerned about the configuration method of the battery and supercapacitor.This may lead to complex control circuits and inefficient control processes.A typical distribution network structure with hierarchical storage is shown in Figure 4.
Equivalent model circuit for the supercapacitor.

Hierarchical Structure
At present, many different kinds of energy storage devices are known, including batteries, supercapacitors, flywheels, superconducting magnetics and so on, most of which have different charge and discharge characteristics [15,16].The bidirectional energy adjustment ability of energy storage devices make them play an important role in photovoltaic power systems.Compared with the single-technology energy storage system (ESS), a HESS can combine the advantages of each technology used, thus being more suitable for large-scale renewable energy systems.Typical combinations may include a battery and supercapacitor.
However, most storage devices are configured in the same place or just near photovoltaic power generators, so researchers are not very concerned about the configuration method of the battery and supercapacitor.This may lead to complex control circuits and inefficient control processes.A typical distribution network structure with hierarchical storage is shown in Figure 4.In this typical structure, the centralized storage refers to a large-scale energy storage system consisting of mass energy storage devices connected in series or in parallel, that is generally configured in a particular area.The distributed storage refers to small-scale storage devices which are installed throughout the distribution network, and are generally configured in the same or nearby nodes of the photovoltaic system, in order to constitute a combined photovoltaic and storage power-generation system.Centralized storage is mainly used to implement overall coordinated control of distribution networks, while distributed storage takes charge of local power balancing of photovoltaics.
As the control targets of centralized storage and distributed storage are different, it's necessary to select suitable storage devices to fit each target.Storage batteries have characteristics of low Construction of a distribution network with high permeability photovoltaic/ hierarchical storage.
In this typical structure, the centralized storage refers to a large-scale energy storage system consisting of mass energy storage devices connected in series or in parallel, that is generally configured in a particular area.The distributed storage refers to small-scale storage devices which are installed throughout the distribution network, and are generally configured in the same or nearby nodes of the photovoltaic system, in order to constitute a combined photovoltaic and storage power-generation system.Centralized storage is mainly used to implement overall coordinated control of distribution networks, while distributed storage takes charge of local power balancing of photovoltaics.As the control targets of centralized storage and distributed storage are different, it's necessary to select suitable storage devices to fit each target.Storage batteries have characteristics of low self-discharge, low manufacturing cost and high energy density, which makes them suitable for mass storage for a long time, so they are configured to constitute a centralized storage system (CSS).On the other hand, supercapacitors have high charge efficiency, high power density and rapid response speed.They are mainly used to adjust power oscillations of photovoltaics and they are configured to constitute a distributed storage system (DSS).
According to the configuration scheme, the high-frequency power oscillations are assigned to supercapacitors and the low-frequency oscillations are handled by storage batteries.Although the manufacturing cost of supercapacitors is higher than that of storage batteries, the smaller high-frequency power oscillations lead to smaller required supercapacitor capacity.This also conforms to the fact that supercapacitors are difficultly to scale at high power ratings due to cell voltage unbalancing issues.

Control of a Single DC Bus Voltage
Firstly, we consider a single distributed storage system with storage batteries.The system structure is shown in Figure 5.
Energies 2016, 9, 395 5 of 15 self-discharge, low manufacturing cost and high energy density, which makes them suitable for mass storage for a long time, so they are configured to constitute a centralized storage system (CSS).
On the other hand, supercapacitors have high charge efficiency, high power density and rapid response speed.They are mainly used to adjust power oscillations of photovoltaics and they are configured to constitute a distributed storage system (DSS).According to the configuration scheme, the high-frequency power oscillations are assigned to supercapacitors and the low-frequency oscillations are handled by storage batteries.Although the manufacturing cost of supercapacitors is higher than that of storage batteries, the smaller high-frequency power oscillations lead to smaller required supercapacitor capacity.This also conforms to the fact that supercapacitors are difficultly to scale at high power ratings due to cell voltage unbalancing issues.

Control of a Single DC Bus Voltage
Firstly, we consider a single distributed storage system with storage batteries.The system structure is shown in Figure 5.In the power allocation type control strategy, the voltage balance of the DC bus is controlled by both the photovoltaic and the energy storage system.The inverter power is given by the system as PI_ref.The output of the photovoltaic and load can be obtained by a prediction algorithm.Thus, the relational expressions of power are: According to the allocation principle of high and low frequency power oscillations, we use a low pass filter (LPF) to obtain the reference power of the supercapacitor and battery.The control block diagram is shown in Figure 6.
The transfer function of LPF is G(s) = 1/1+Ts, so the reference power of supercapacitor and battery are: where T is the time constant of LPF.In the power allocation type control strategy, the voltage balance of the DC bus is controlled by both the photovoltaic and the energy storage system.The inverter power is given by the system as P I_ref .The output of the photovoltaic and load can be obtained by a prediction algorithm.Thus, the relational expressions of power are: P PV `PESS_re f " P L&I_re f (5) According to the allocation principle of high and low frequency power oscillations, we use a low pass filter (LPF) to obtain the reference power of the supercapacitor and battery.The control block diagram is shown in Figure 6.
The transfer function of LPF is G(s) = 1/1+Ts, so the reference power of supercapacitor and battery are: where T is the time constant of LPF.
Energies 2016, 9, 395 6 of 15 Now, we discuss the relationship between the time constant and the necessary capacity of the storage system.Usually, we can get the forecast power curve of the photovoltaic and load.Setting the time constant T, we can get PB_ref and PSC_ref from Equations ( 4)- (8).Then, we calculate the integral for PB_ref and PSC_ref according to the control time.Finally, considering the efficiency and capacity margin, we can obtain the needed storage system capacity.

Control of System
Considering multiple distributed storage systems with a centralized storage system, the paper proposes an improved control structure upon construction of the distribution network shown in Figure 4. Taking three distributed storage systems as an example, the control structure is shown as Figure 7. Except for those installed in series with the photovoltaic array, all DC/DCs are bidirectional.Focusing on DSS1, the outputs of photovoltaic, supercapacitor and battery adjust the voltage of DC bus1 together.Now PB1 is the required power of battery.According to the aforementioned control method, PB1 is: Now, we discuss the relationship between the time constant and the necessary capacity of the storage system.Usually, we can get the forecast power curve of the photovoltaic and load.Setting the time constant T, we can get P B_ref and P SC_ref from Equations ( 4)-( 8).Then, we calculate the integral for P B_ref and P SC_ref according to the control time.Finally, considering the efficiency and capacity margin, we can obtain the needed storage system capacity.

Control of System
Considering multiple distributed storage systems with a centralized storage system, the paper proposes an improved control structure upon construction of the distribution network shown in Figure 4. Taking three distributed storage systems as an example, the control structure is shown as Figure 7. Except for those installed in series with the photovoltaic array, all DC/DCs are bidirectional.
Energies 2016, 9, 395 6 of 15 Now, we discuss the relationship between the time constant and the necessary capacity of the storage system.Usually, we can get the forecast power curve of the photovoltaic and load.Setting the time constant T, we can get PB_ref and PSC_ref from Equations ( 4)- (8).Then, we calculate the integral for PB_ref and PSC_ref according to the control time.Finally, considering the efficiency and capacity margin, we can obtain the needed storage system capacity.

Control of System
Considering multiple distributed storage systems with a centralized storage system, the paper proposes an improved control structure upon construction of the distribution network shown in Figure 4. Taking three distributed storage systems as an example, the control structure is shown as Figure 7. Except for those installed in series with the photovoltaic array, all DC/DCs are bidirectional.Focusing on DSS1, the outputs of photovoltaic, supercapacitor and battery adjust the voltage of DC bus1 together.Now PB1 is the required power of battery.According to the aforementioned control method, PB1 is: Focusing on DSS1, the outputs of photovoltaic, supercapacitor and battery adjust the voltage of DC bus1 together.Now P B1 is the required power of battery.According to the aforementioned control method, P B1 is: Energies 2016, 9, 395 7 of 15 Similarly, we have: Defining P inv as power vacancy from AC bus, we can obtain the energy control relationship as Through the above analysis, we know that supercapacitors in the distributed storage system are only used to balance the high-frequency power oscillations of the DC bus.Batteries in a centralized storage system have two effects, one is to balance the low-frequency power oscillations of DC bus as P B1 , P B2 and P B3 , the other is to remain the power balance of AC bus as P inv .This configuration structure can manage mass batteries in one place in a centralized way, which can reduce the control modules that need to be distributed in the distribution network.Moreover, different DC buses have different voltage grades, thus this is convenient for accessing various DC loads.

Constraint Condition
The above discussion doesn't include photovoltaic and energy storage constraints, but actually the parameters of devices are important and the system restrictions need to be taken into account when formulating control strategies.
The system power balance constraint is: where P PV is the photovoltaic output power, n is the total number of photovoltaics, P ES is the output power of each energy storage.In this case, it's only a battery.When it's positive, energy storage is discharging, while when it's negative, energy storage is charging.l is the total number of energy storage devices.P SPG is the tie-line power of other power grids.P L_AC is the AC load power.The bus-bar voltage constraint is: where U e is the rated bus-bar voltage and U BUS is the actual bus-bar voltage.Photovoltaic output constraint is: where P PVimin and P PVimax are the inferior and superior power limits for the photovoltaic, respectively.Battery and supercapacitor power constraints are: P SCmin ď P SC ď P SCmax (17) where P B is the actual battery power, P SC is the actual supercapacitor power.P Bmin and P Bmax are the inferior and superior power limits of the batteries, respectively.P SCmin and P SCmax are the inferior and superior power limita of the supercapacitor, respectively.
The state of charge (SOC) of the battery is calculated as: where SOC B is the actual SOC of the battery, SOC B0 is the initial battery SOC, C N is the rated capacity of the battery, λ is the influence factor of battery capacity, η is the battery efficiency.
The SOC of supercapacitor is related to its voltage, which can be expressed as: where SOC SC is the actual SOC of the supercapacitor, U SC ptq is the actual voltage of the supercapacitor, and U SCmax is the maximum allowable voltage of the supercapacitor.Thus, the battery and supercapacitor SOC constraints are: where SOC Bmin and SOC Bmax are the inferior and superior SOC limits for batteries, respectively, and SOC SCmin and SOC SCmax are the inferior and superior SOC limits for supercapacitors, respectively.

Centralized Management of Mass Batteries
Mass batteries connected in series or parallel bring problems of current and voltage sharing.After working for a long time, the SOC of each battery cannot stay the same.Coordination control of all batteries becomes complex and difficult.Thus a hierarchical management structure of batteries is proposed, which divides battery management into battery management, battery cluster management and battery array management, as shown in Figure 8.
Energies 2016, 9, 395 8 of 15 where SOCB is the actual SOC of the battery, SOCB0 is the initial battery SOC, CN is the rated capacity of the battery, λ is the influence factor of battery capacity, η is the battery efficiency.
The SOC of supercapacitor is related to its voltage, which can be expressed as: where SOCSC is the actual SOC of the supercapacitor, ()

SC
Ut is the actual voltage of the supercapacitor, and max SC U is the maximum allowable voltage of the supercapacitor.
Thus, the battery and supercapacitor SOC constraints are:

Centralized Management of Mass Batteries
Mass batteries connected in series or parallel bring problems of current and voltage sharing.After working for a long time, the SOC of each battery cannot stay the same.Coordination control of all batteries becomes complex and difficult.Thus a hierarchical management structure of batteries is proposed, which divides battery management into battery management, battery cluster management and battery array management, as shown in Figure 8. Battery management in the bottom layer takes charge of single battery voltage sampling, multipoint temperature collection and battery equalization control.Battery cluster management in middle layer controls all the batteries of a battery cluster, taking charge of the total voltage acquisition of the battery string, charging and discharging current collection, electric leakage detection, failure warnings and SOC calculations.It realizes high-voltage management and completes the equilibrium control of the battery cluster.Battery array management in the top layer controls all battery clusters in the whole battery system.By collecting data and warning information from battery strings, it summarizes, counts, analyzes and deals with all the information of the battery system, in order to make batteries meet the requirements of centralized control [17].The control circuits of each layer are shown in Figure 9.
The single battery management circuit includes a main control, battery monitoring, battery switching, communication interface and so on.An LTC6802 is an IC for battery monitoring which is used as the main management chip.The configuration purpose of the power input and auxiliary Battery management in the bottom layer takes charge of single battery voltage sampling, multipoint temperature collection and battery equalization control.Battery cluster management in middle layer controls all the batteries of a battery cluster, taking charge of the total voltage acquisition of the battery string, charging and discharging current collection, electric leakage detection, failure warnings and SOC calculations.It realizes high-voltage management and completes the equilibrium control of the battery cluster.Battery array management in the top layer controls all battery clusters in the whole battery system.By collecting data and warning information from battery strings, it summarizes, counts, analyzes and deals with all the information of the battery system, in order to make batteries meet the requirements of centralized control [17].The control circuits of each layer are shown in Figure 9.The single battery management circuit includes a main control, battery monitoring, battery switching, communication interface and so on.An LTC6802 is an IC for battery monitoring which is used as the main management chip.The configuration purpose of the power input and auxiliary charge DC/DC is to balance the SOC of different batteries.Two microprocessors are applied in the battery cluster management circuit.The master microprocessor is responsible for operational management of the control circuit, while the slave microprocessor takes charge of current collection and relevant calculations.Up CAN and Low CAN is respectively used to communicate with the battery array and single battery management circuits.Finally, the UI control interface and communication network are arranged in  The master microprocessor is responsible for operational management of the control circuit, while the slave microprocessor takes charge of current collection and relevant calculations.Up CAN and Low CAN is respectively used to communicate with the battery array and single battery management Energies 2016, 9, 395 10 of 15 circuits.Finally, the UI control interface and communication network are arranged in the battery array management.Through this control structure, we expect to realize coordinated control of batteries.

Simulation
The simulation platform is built by PSCAD to assess the performance of the energy management strategy.The simulation parameters are listed in Table 1.We select a typical photovoltaic and energy-storage hybrid distribution network, and obtain the corresponding photovoltaic output prediction curve by some prediction technique such as a grey forecasting model or neural network [18].To simplify the simulation process, we assume a constant DC load P load = 49 kW.

Single Control for a Short Time Scale
We take a single DC bus as an example to verify the regulating effect of battery and supercapacitor.The output waveforms for different time constants are shown in Figure 10.The numbers of batteries in series and parallel are 110 and 20, respectively, while the numbers of series and parallel supercapacitors are 150 and 2.
Figure 10a shows that when T = 0.1 s, the supercapacitor output has a fast fluctuation, but its fluctuation amplitude is small.Part of the high-frequency fluctuating power is adjusted by batteries.That makes the battery power output change frequently, which will reduce the battery's service life.Figure 10d shows that when T = 10 s, the supercapacitor amplitude fluctuation is quite large, but the supercapacitor can hardly be scaled at a high power rating.What's more, the battery outputs cannot track the photovoltaic fluctuations efficiently.Thus, a reasonable time constant can ensure a better control effect.Through the simulation waveform, we know that when 1 s < T < 5 s, the control effect is quite ideal.
Energies 2016, 9, 395 10 of 15 the battery array management.Through this control structure, we expect to realize coordinated control of batteries.

Simulation
The simulation platform is built by PSCAD to assess the performance of the energy management strategy.The simulation parameters are listed in Table 1.
Table 1.Battery and supercapacitor simulation parameters.We select a typical photovoltaic and energy-storage hybrid distribution network, and obtain the corresponding photovoltaic output prediction curve by some prediction technique such as a grey forecasting model or neural network [18].To simplify the simulation process, we assume a constant DC load Pload = 49 kW.

Single Control for a Short Time Scale
We take a single DC bus as an example to verify the regulating effect of battery and supercapacitor.The output waveforms for different time constants are shown in Figure 10.The numbers of batteries in series and parallel are 110 and 20, respectively, while the numbers of series and parallel supercapacitors are 150 and 2.
Figure 10a shows that when T = 0.1 s, the supercapacitor output has a fast fluctuation, but its fluctuation amplitude is small.Part of the high-frequency fluctuating power is adjusted by batteries.That makes the battery power output change frequently, which will reduce the battery's service life.Figure 10d shows that when T = 10 s, the supercapacitor amplitude fluctuation is quite large, but the supercapacitor can hardly be scaled at a high power rating.What's more, the battery outputs cannot track the photovoltaic fluctuations efficiently.Thus, a reasonable time constant can ensure a better control effect.Through the simulation waveform, we know that when 1 s < T < 5 s, the control effect is quite ideal.

Single Control for a Long Time Scale
Considering single control for a long time scale, we select the daytime output of the photovoltaic system.Due to the extended control time, larger battery and supercapacitor capacities are required.Meanwhile, the time constant will be longer than in the former simulation.Now the numbers of batteries in series and parallel are 110 and 100, respectively, while the numbers of series and parallel supercapacitors are 150 and 80.The output waveforms for different time constants are shown in Figure 11.When T = 150 s, the output waveform of the battery is unsmooth.Battery power changes acutely, which will lead to a shorter battery service life.When T = 2400 s, due to the capacity

Single Control for a Long Time Scale
Considering single control for a long time scale, we select the daytime output of the photovoltaic system.Due to the extended control time, larger battery and supercapacitor capacities are required.Meanwhile, the time constant will be longer than in the former simulation.Now the numbers of batteries in series and parallel are 110 and 100, respectively, while the numbers of series and parallel supercapacitors are 150 and 80.The output waveforms for different time constants are shown in Figure 11.

Single Control for a Long Time Scale
Considering single control for a long time scale, we select the daytime output of the photovoltaic system.Due to the extended control time, larger battery and supercapacitor capacities are required.Meanwhile, the time constant will be longer than in the former simulation.Now the numbers of batteries in series and parallel are 110 and 100, respectively, while the numbers of series and parallel supercapacitors are 150 and 80.The output waveforms for different time constants are shown in Figure 11.When T = 150 s, the output waveform of the battery is unsmooth.Battery power changes acutely, which will lead to a shorter battery service life.When T = 2400 s, due to the capacity The results show that supercapacitors in each distributed storage system can stabilize the high-frequency fluctuating power well.The low-frequency part can be assigned reasonably through the converging bus (DC Bus 4).

Conclusions and Prospects
Energy management of hybrid energy systems is significant against the background of wide application of photovoltaic generation.This paper models photovoltaics, storage batteries and supercapacitors, and then introduces a typical distribution network structure with hierarchical storage.A low pass filter is used to achieve regulation of high and low frequency photovoltaic fluctuations.The high-frequency power oscillations are assigned to supercapacitors and the low-frequency oscillations are handled by storage batteries.On this basis, the paper proposes an improved configuration structure which is convenient for accessing various DC loads and can centrally manage mass batteries in one place.Compared to traditional hybrid storage structures, this hierarchical structure can simplify the control circuit and control process, and improve control efficiency.To solve the problem caused by centralized management of mass batteries, the paper introduces a three-layer management structure.The control objects and control circuits are discussed.
The simulation results verify the control effect of battery and supercapacitor.When the time constant 1 s < T < 5 s, a better output waveform can be achieved.More experiments should be done however to verify the control effectiveness of multiple distributed storage systems.Power scheduling of centralized storage systems with AC buses should also be taken into consideration.The hierarchical control structure is expected to optimize the operation of photovoltaic and energy-storage hybrid systems.

Figure 1 .
Figure 1.Equivalent circuit of a solar cell.

Figure 1 .
Figure 1.Equivalent circuit of a solar cell.

Figure 4 .
Figure 4. Construction of a distribution network with high permeability photovoltaic/hierarchical storage.

Figure 4 .
Figure 4. Construction of a distribution network with high permeability photovoltaic/hierarchical storage.

Figure 4 .
Figure 4.Construction of a distribution network with high permeability photovoltaic/ hierarchical storage.

Figure 5 .
Figure 5. System structure of a single distributed storage system with storage batteries.

Figure 5 .
Figure 5. System structure of a single distributed storage system with storage batteries.

Figure 6 .
Figure 6.Control block diagram of a single distributed storage system with storage batteries.

Figure 7 .
Figure 7.Control structure of a multiple distributed storage system with centralized storage system.

Figure 6 .
Figure 6.Control block diagram of a single distributed storage system with storage batteries.

Figure 6 .
Figure 6.Control block diagram of a single distributed storage system with storage batteries.

Figure 7 .
Figure 7.Control structure of a multiple distributed storage system with centralized storage system.

Figure 7 .
Figure 7.Control structure of a multiple distributed storage system with centralized storage system.
are the inferior and superior SOC limits for batteries, respectively, and min SC SOC and max SC SOC are the inferior and superior SOC limits for supercapacitors, respectively.

Figure 8 .
Figure 8. Hierarchical management structure of batteries.

Figure 8 .
Figure 8. Hierarchical management structure of batteries.

Figure 9 .
Figure 9. Battery management control circuits: (a) Single battery management and (b) Battery cluster management and (c) Battery array management.

Figure 9 .
Figure 9. Battery management control circuits: (a) Single battery management and (b) Battery cluster management and (c) Battery array management.

Table 1 .
Battery and supercapacitor simulation parameters.