Real-Time Wavelet-Based Coordinated Control of Hybrid Energy Storage Systems for Denoising and Flattening Wind Power Output

Since the penetration level of wind energy is continuously increasing, the negative impact caused by the fluctuation of wind power output needs to be carefully managed. This paper proposes a novel real-time coordinated control algorithm based on a wavelet transform to mitigate both short-term and long-term fluctuations by using a hybrid energy storage system (HESS). The short-term fluctuation is eliminated by using an electric double-layer capacitor (EDLC), while the wind-HESS system output is kept constant during each 10-min period by a Ni-MH battery (NB). State-of-charge (SOC) control strategies for both EDLC and NB are proposed to maintain the SOC level of storage within safe operating limits. A ramp rate limitation (RRL) requirement is also considered in the proposed algorithm. The effectiveness of the proposed algorithm has been tested by using real time simulation. The simulation model of the wind-HESS system is developed in the real-time digital simulator (RTDS)/RSCAD environment. The proposed algorithm is also implemented as a user defined model of the RSCAD. The simulation results demonstrate that the HESS with the proposed control algorithm can indeed assist in dealing with the variation of wind power generation. Moreover, the proposed method OPEN ACCESS Energies 2014, 7 6621 shows better performance in smoothing out the fluctuation and managing the SOC of battery and EDLC than the simple moving average (SMA) based method.


Introduction
Recently, the exhaustion of fossil fuels and the critical environmental pollution have led to the need to develop new clean energy sources.Wind energy, a type of renewable and environmental-friendly energy, is considered as a prospective replacement for conventional energy resources.However, because of the stochastic and intermittent characteristic of wind speed, the resulting fluctuation in power output is the greatest obstacle to the increasing penetration level of wind power in power grids [1].In order to reduce the negative impact of these fluctuations on the stability, reliability and protection of the power system, a number of control methods have been proposed.
Many researchers have demonstrated that pitch angle control, in conjunction with other modern controllers such as the fuzzy logic controller, provides a very effective means of regulating aerodynamics to reduce wind power fluctuation [2].However, the short-term fluctuations of wind power output cannot be mitigated by these types of controllers because of the mechanical stress accrued by the wind blade.Abedini et al. [3] used a rotor inertia adjustment method to smooth out wind power output.This approach also does not require any energy storage devices but the rotor speed no longer can be controlled to follow maximum power tracking.
An electrical energy storage system (EESS) is recognized as an alternative technique to mitigate both short-term and long-term wind power fluctuations.Various benefits of using EESS in wind power applications are discussed in [4].The cooperation of different storage devices with different charge/discharge characteristics makes it possible to balance both power-and energy-scale requirements.Among various hybrid energy storage system (HESS) options, this paper focuses on the Ni-MH battery (NB)-electric double-layer capacitor (EDLC) HESS as a solution to mitigate the wind power fluctuation.EDLC is suitable for denoising wind power output because it has a number of exceptional characteristics, including high power density, fast charge/discharge process, high efficiency, and long lifetime [5].On the other hand, NB with high energy density characteristic is fit for flattening wind power fluctuations.
In the existing literature, a moving average technique and the first-order delay filter (FDF), the simplest methods, have been applied to smooth out wind power fluctuation [6][7][8][9][10].Ushiwata et al. [6] presented a smoothing approach to mitigate wind power fluctuations using EDLC and the simple moving average (SMA) control method.Tanabe et al. [7] used FDF with an adjustable time constant and additional rate limiter to keep the fluctuation of wind power output within 10% for 20 min , while Sheikh et al. [8] proposed a hybrid control algorithm including both SMA and exponential moving average (EMA) to generate output power reference of static synchronous compensator (STATCOM)/superconducting magnetic energy storage (SMES) system.A state-of-charge (SOC) regulation method of a battery in a hybrid wind power/battery energy storage system has been proposed in [9], and hardware-in-the-loop (HIL) simulation studies of a wind turbine coupled with battery supercapacitor EESS has been presented in [10].Both are based on simple filtering algorithms.Some researchers have proposed intelligent approaches for EESS power dispatching and scheduling.Suvire et al. [11] utilized a fuzzy inference system to control the active power of the distribution static synchronous compensator (DSTATCOM) coupled with flywheel energy storage system to smooth out wind power fluctuation, whereas Mishra et al. [12] used a bacteria foraging technique to integrate wind turbine and batteries to maintain a constant grid power output.Li et al. [13] proposed a control algorithm cooperating wavelet transform with fuzzy logic control to smooth a hybrid system including photovoltaic and wind power systems by using a battery energy storage system.However, these methods are implemented via non-real time process, which limits the real-time application.Furthermore, they failed to neither ensure the system power output always satisfies ramp rate requirements nor consider to safe working limits of EESS.Jiang et al. [14] implemented a wavelet-based capacity configuration and coordinated control algorithm for reducing output power fluctuations of a wind system using a lithium-ion battery-ultra-capacitor energy storage system.Although this paper proposed a novel approach for solving most of the above problems, it still used two stages of wavelet filtering that increase the computational complexity and require wind data prediction algorithm.The various features of the previous researches are summarized in Table 1.
Table 1.Comparison of various wind power smoothing methods.SOC: state-of-charge; SMA: simple moving average; EDLC: electric double-layer capacitor; EMA: exponential moving average; and SMES: superconducting magnetic energy storage.

Interconnection requirement
Real-time or hardware test Ushiwata [6] SMA EDLC X X X Tanabe [7] SMA Battery X O X Sheikh [8] SMA + EMA SMES X X X Yoshimoto [9] First order lag filter Battery O X X Li [10] SMA Battery/EDLC X X O Suvire [11] Fuzzy logic + SMA Flywheel X X X Mishra [12] Bacteria foraging Battery X X X Li [13] Fuzzy logic + wavelet Battery O X X Jiang [14] Online From the above literature review, the requirements of the wind HESS system can be summarized as follows: (i) better performance in smoothing out the wind power fluctuation; (ii) efficient energy management of HESS for SOC regulation; (iii) grid interconnection requirement; and (iv) easy implementation in actual hardware.Considering the above requirements, this paper proposes a novel real-time wavelet-based energy management algorithm (RWEMA) to coordinate a NB-EDLC HESS.The proposed algorithm includes the SOC regulation strategies considering practical issues, such as charge/discharge losses and inverter efficiency.For improved filtering and the real-time applicability, we adopted the online wavelet transform proposed in [15].The real-time digital simulator (RTDS), which provides reliable and accurate computation in hard real time, is used to model the system and to implement and validate the proposed algorithm [16].
This paper is organized as follows: Section 2 presents the modeling of each energy storage device; Section 3 introduces the RWEMA; in Section 4, the simulation studies are carried out in the RTDS/RSCAD environment to validate the effectiveness of the proposed algorithm; finally, some conclusions are given in Section 5.

Wind-Hybrid Energy Storage System Modeling in RSCAD
Integrating EESS with a wind power system will reduce the power output fluctuation.In order to reduce both short-term and long-term fluctuations, this paper proposes the combination of the NB and EDLC energy storage system to satisfy both high power and energy capacity requirements.
The typical wind power system as illustrated in Figure 1 is used for simulation studies in this research.In this system, an induction machine-based wind turbine is integrated with the corresponding HESS.A Vestas V82 wind turbine model is provided in the RSCAD library (Winnipeg, MB, Canada), but the simulation models of the NB and EDLC are not given in the RSCAD.Therefore, the RSCAD simulation models of NB and EDLC are developed based on general mathematical models.A RWEMA is added to provide the charge/discharge references PEDLC,ref and PNB,ref, which are then fed to the corresponding DC/AC inverter.The total active power at the point of common coupling (PCC) Psys is the sum of the wind power output, EDLC, and the NB output (Pwind, PEDLC, and Pbatt, respectively).

Development of Electric Double-Layer Capacitor Simulation Model in RSCAD
EDLC is an electrochemical capacitor that consists of two electrodes to allow a potential to be applied across the cell; two double layers are therefore present, one at each electrode/electrolyte interface.Since EDLC has a number of advantages such as high power density, fast charge/discharge process, long lifetime and low temperature performance, it is considered to be a very promising energy storage device used to mitigate short-term fluctuation of wind power output [17].For the simulation studies, EDLC is modeled as an ideal voltage source in series with an equivalent resistance, where the value of the voltage source is calculated from the dynamic model, as shown in Figure 2. The dynamic model represents the electrochemical behavior of EDLC.In this paper, a mathematical model consisting of Stern and Tafel equations is used that gives the relationship between voltage, current and the available amount of charge during charging/discharging processes [18].The input of this model is the current obtained from the terminal of EDLC, and the outputs are the voltage and the SOC of EDLC.The detailed block diagram of the dynamic model is shown in Figure 3.The amount of electric charge in EDLC (Q) is calculated as Equation (1), where Qinit is the initial amount of charge, i is the measured current, and isd is the self-discharge current: The saturation limit function is used to restrict the calculated amount of charge within a specific range to prevent the full discharge and overcharge of EDLC.The Tafel equation given by Equation ( 2) is used to calculate the leakage current isd that represents the self-discharge phenomenon of EDLC: Finally, the voltage value of the controlled voltage source is obtained from the Stern equation as follows: where: The additional details of parameter declaration and calculation are given in [19].The other required parameters are computed from basic electrochemical equations and some known constants such as Avogadro, ideal gas and Stefan-Boltzmann constants, etc.
In order to represent different initial SOC level of EDLC, the initial amount of charge of EDLC (Qinit) should be calculated before the simulation starts.Since the capacitance of EDLC is nonlinear and dependent on the open circuit voltage, Qinit can be represented by a function of the initial open circuit voltage (Vinit), governed by: For the purpose of simplifying the simulation model, the above nonlinear voltage-capacitance dependence is rewritten so that the capacitance C is kept constant while Qinit is approximated as follows: The function f(Vinit) is obtained for a specific EDLC module under test, which consists of 3000 F Maxwell BootsCap Devices (San Diego, CA, USA).For this, the simulation is implemented with an EDLC model provided by Simscape module in MATLAB Simulink [19].The Qinit data is captured by changing the initial voltage from 0 V to 2.8 V (equivalent to SOC level from 0% to 100%) while the EDLC is either fully charged or fully discharged with a constant current.From the simulation data, the relationship between Vinit and Qinit is established by curved fitting as follows: Based on the above mathematic model, a user-defined model (UDM) of EDLC is made by using the component builder in the RSCAD.From the configuration interface of the developed UDM, the parameters of EDLC can be modified to satisfy the requirements of different simulation cases, as shown in Figure 4.

Development of Ni-MH Battery Simulation Model in RSCAD
The first NB was introduced in 1990 by Sanyo Electric Company in Osaka, Japan.This battery type has a number of advantages such as having high energy density and high efficiency, and containing no toxic metals.Since its response is slower than EDLC, it is used to reduce long-term wind power fluctuation.
NB is also modeled as a controllable voltage source, where the value of the voltage source is calculated from the dynamic model.In this study, the modified Shepherd-based mathematic model of NB presented in [20] is used.This model includes an equation to describe the electrochemical behavior of a battery directly in terms of terminal voltage, open circuit voltage, internal resistance, discharge current, and SOC.This model is based on a number of specific assumptions and limitations, including the internal resistance is supposed to be constant and temperature effect is not considered.
The value of the voltage source during the discharge and charge process can be calculated by using Equations ( 7) and ( 8), respectively: where: Vbatt battery voltage (V); E0 battery constant voltage (V); Based on Equations ( 7) and ( 8), the UDM of NB is also created by using the component builder module in the RSCAD environment.Figure 5 shows the main parameter configuration menu of the NB model.The parameters and stack configuration of the battery can be modified through this interface.

Real-Time Wavelet-Based Energy Management Algorithm
The application of discrete wavelet transform (DWT) in the wind power system is actually a filtering process, in which the wind power output is decomposed into smoothed and noised components.This process can be classified into non-real-time and real-time methods.In this paper, a real-time wavelet method is implemented based on a moving window function (MWF) [15].This MWF has a length of n and is designed to store wind power output data as a first-in first-out buffer.The proposed RWEMA controller dynamically obtains the results from MWF and the SOC from the EDLC and NB bank, and then determines the reference value for the corresponding DC/AC inverter controller of HESS.Furthermore, the SOC control strategies are added to maintain the SOC levels of storage within their safe operating limits, which are normally between 20% and 80% for battery [14] and between 30% and 90% for EDLC.
The objective of the proposed RWEMA is to both denoise and flatten the total wind-HESS system output during the specified time period.In order to obtain a constant total power output every 10 min, an average buffer with a length of m is used in the RWEMA.The procedure of the proposed RWEMA consists of three key stages: data processing and DWT procedure, SOC control strategy, and ramp rate limitation (RRL).

Data Processing and Discrete Wavelet Transform Procedure
Step 1: During the first n seconds, the wind power output data is sampled every second and added to the MWF: Step 2: As soon as the MWF is filled, the MWF is extended by using a short-symmetric method to deal with some of the disadvantages of real-time wavelet transform such as border distortion and the pseudo-Gibbs phenomena [15].The length of MWF is increased, and the pre-processed wind power series becomes: Step 3: The wind power output in the extended MWF is decomposed into two corresponding components by passing it through low-pass and high-pass filter to the l-th level.The level-l low-frequency component and the sum of the l-level high-frequency terms are:   Step 4: The n-th data of the high and low frequency component are sent to SOC control strategy stage described in Section 3.2.The modified high frequency component is directly used to determine the active power reference for the inverter controller of EDLC.The modified low frequency component is then added to the average buffer.As soon as the average buffer is filled, the system output reference for the next 10 min ( sys,ref ) is calculated by taking the average of the buffer and applying the 10-min RRL constraint given in Section 3. Step 5: Subsequently, the new data from the wind power output is added to the last position of MWF and the first data is removed.Repeat Steps 2-5 with the updated MWF.A flowchart of the complete algorithm is illustrated in Figure 6.
Since the average of the previous 10-min period is used as a reference for the next period, the proposed method does not require any additional forecasting technique.The combined power output of the wind turbine and HESS defined by Equation ( 14

State-of-Charge Control Strategies
The SOC levels of the storage devices continuously vary during the charge/discharge process.Furthermore, the non-ideal charging and discharging efficiency of NB and EDLC slowly reduces their SOC level.Since the capacity of the storage devices is limited, the SOCs of NB and EDLC may exceed their safe operating limits.In that case, HESS will be disconnected from the grid for safety, and the regulation effect will no longer exist.To avoid or even reduce these unexpected situations, this paper proposes SOC control strategies.

State-of-Charge Control Strategy of the Electric Double-Layer Capacitor
The high frequency component ).In order to keep the SOC within the specified limits, an offset term is added to D t P as Equation (15), where αEDLC is a tuning constant determined depending on the EDLC SOC level, and PEDLC,rated is the rated power of the EDLC: If the SOC level is within a safe range, 45%-75% in this research, the offset term will be zero.If the SOC level is above this range, the offset term should be negative in order to reduce charging or increase discharging, while the term should be positive in the opposite case.Moreover, the magnitude of the offset term should increase as the SOC level further deviates from the safe range.
When the losses during the charge/discharge process are considered, the offset term is slightly modified.Considering the efficiency of the EDLC and the inverter, the charged (PEDLC,c) and discharged (PEDLC,d) power can be calculated as follows: where ηc and ηd are the charging and discharging efficiency of EDLC, respectively; ηinv is the efficiency of the inverter; and Pref,c and Pref,d are the electrical charge and discharge references of EDLC, respectively.Thus, the SOC level of EDLC will gradually decrease with time, even though the average value of the charge and discharge reference value is zero.In this paper, the charging and discharging efficiencies of EDLC are assumed to be 98%, whereas the efficiency of the inverter is chosen to be 97%.The power loss in the charge and discharge process is determined as: (1 η η ) 0.049 When the electrical charge/discharge value is the rated power of EDLC as shown in Figure 7, the maximum total power loss during a charge/discharge cycle can be expressed as: Loss,d max max max Loss EDLC,rated 0.1 Figure 7. Charge/discharge energy of EDLC with rated power.
The magnitude of the high frequency component of wind power rarely reaches the maximum, and is usually very small compared to the rated power of EDLC.Based on our test, the absolute average of the high frequency component is about 8%-10% of PEDLC,rated.Therefore, in this research, the average power loss in EDLC and in the inverter is chosen as 1% of PEDLC,rated.To compensate for the loss, this amount of power should be added to the offset term discussed above.The tuning constants for EDLC, considering both the SOC level control and loss compensation, are listed in Table 2 according to the SOC level.

State-of-Charge Control Strategy of the Ni-MH Battery
The main concept of the SOC control strategy for NB is similar to that of EDLC.However, in this case, the NB inverter reference is not directly modified.Instead, the system output reference of the next 10-min period is adjusted according to the change of the NB SOC level.If the SOC level is above the maximum safe range, the system output reference should be increased so that the discharge power is increased.On the contrary, when the SOC level is very low, the SOC level can be increased or less reduced by decreasing the system output reference.For this, the low frequency component at time t ( A t P ) is multiplied by a different tuning constant depending on the NB SOC level as follows: The tuning constant αNB used in the research is summarized in Table 2.It should be noted that the tuning constant for a safe range (40%-60% in this research) is unity, not zero.

Ramp Rate Limitation Requirement
Since both short-term and long-term wind power fluctuations severe negative effects on power system quality, stability, and reliability, they should be restricted within a certain limit, especially at a high wind power penetration level [14].Several different RRLs have been proposed, depending on the recent situation of wind power of each country or the policies of power utilities.For example, the Hawaiian Electric Company (Honolulu, HI, USA) limits the ramp rate at ±2 MW/min at all times, whereas in Germany, the maximum ramp rate for a wind power system is 10% of the rated power of the wind turbine (Pwt,rated) per minute [21].In this paper, in order to obtain constant total power output every 10 min, two RRLs that were recently used in Ireland are selected, as shown in Figure 8 [22].

Wind power output
A 1-min requirement defined by Equation ( 22) is used to limit the ramp rate of the total power output, while a 10-min requirement in Equation ( 23) is used to prevent overshooting when the system power reference is changed.Here, the term k is used to count the change of the system reference every 10 min, whereas the term t represents a 1-s change of system reference:

Configuration of the Test System
The wind-HESS test system shown in Figure 1 is implemented in the RSCAD environment.A Vestas V82 wind turbine model provided in the RSCAD library is used to cooperate with the NB-EDLC HESS.The rated power of the wind turbine is 1.65 MW.Two different wind power output profiles for 2 h (7200 s) shown in Figure 9 are used in the simulations.The capacities of the storage are chosen based on the selected energy management algorithm.The rating of the NB is determined to continuously supply or store 60% of the wind turbine rated power for approximately 600 s.The rating of EDLC is chosen so that it can supply or store 40% of the wind turbine rated power for 60 s.The SOC limits and some operational margins are also considered to determine the ratings of the storage.The detail parameters of the test system are summarized in Table 3.The proposed RWEMA including the DWT algorithm is implemented as a UDM by using the component builder in the RSCAD.In order to satisfy the typical time step (50 µs) of real-time simulation and to reduce the size of the computation, the length of MWF was selected as n = 16.The length of the short-symmetric extension Δt was 4. The decomposition level of DWT was 5, with "Haar" wavelet function [23].To test the effectiveness of the SOC control strategy, the initial SOC levels of NB and EDLC were set at 50%.

Case 1: Without State-of-Charge Control Strategy
In this case, we applied the proposed RWEMA without the SOC control strategies; i.e., no adjustment was applied to the EDLC and NB inverter references, regardless of their SOC level.In addition, it is assumed that the NB and EDLC are disconnected if the SOC level is outside the safe operating limits.As shown in Figure 10, the total system power output was successfully denoised and flattened with the help of HESS until the SOC level of EDLC reached its minimum limit (30%) at 3203 s.Subsequently, even though the short-term fluctuation was included in the system output, the average output of the system was more flattened than the original wind power output.After 5706 s, when the SOC level of NB reached its lower limit, the denoising and flattening effects were no longer present and the total power output fluctuation was the same as that of the original wind turbine power output.

Case 2: With State-of-Charge Control Strategy and Comparison with Simple Moving Average
In this case, full RWEMA including the SOC control strategy was applied, while the other simulation settings were the same as those for Case 1.The simulation results are represented by blue lines in Figure 11.As shown in Figure 11a, the fluctuation of the wind power output was almost completely eliminated.Moreover, the total power output was kept constant during each 10-min period after the linear ramp up/down in the beginning, which demonstrates that the RRL requirements have been met.The SOC profiles of the NB and EDLC are shown in Figure 11d,e, respectively.It is shown that the SOC of HESS could be adaptively maintained within the safe operating limits with the proposed SOC control strategies.
In addition, we implemented a SMA filtering based method and compared the performance with the proposed wavelet transform based algorithm.The simulation results with SMA are represented by red lines in Figure 11.Although the basic requirements could be achieved with the SMA based method, the short term fluctuation remaining in the system output was larger than the results of the RWEMA case.As shown in Figure 11b,c, the differences in the output of the NB and EDLC between the two methods were not significant.However, the accumulated effects of the differences were reflected in the SOC profiles.For a more detailed comparison, we used several indices as follows:  24), refers to the degree to which the SOC values deviate from the desired level, typically chosen to be 50%.A smaller BHI indicates more effective usage of the storage device within the safe operating limits [14]:  

P
) and average system output ( avg sys P ): the losses in the NB and EDLC during the charge/discharge process and the losses in the inverter will affect the total system output.The average system output is closely related to the revenue of the wind power system operator.The average power loss of the NB and EDLC is defined as Equation ( 25), where T = 7200 in this study: In other words, the proposed RWEMA not only reduces the inverter rating, but also more effectively manages the usage of NB.Moreover, the power losses of NB and EDLC were 18.67% and 40.15% smaller, respectively, than those in the SMA method.Consequently, the total system power output was increased by 0.017 MW on average, which is 1.03% of the rated power of the wind turbine.The simulation results for the Wind Pattern 2 also proved superiority of RWEMA over SMA as shown in Figure 12 although the differences in performance indices were not as large as those of Wind Pattern 1.
As shown in Figures 11b and 12b, the status of charge/discharge of NB changes frequently and the magnitude of energy absorption and release is not regular in this Wind-HESS application.Therefore, the cycle life of NB may be decreased.Basically, achievable cycle count (ACC) of a battery is increased when the depth of discharge (DOD) is decreased [24,25].However, the actual cycle life of a battery should be evaluated by the amount of transferred energy during its whole life rather than the cycle count [24].Since the DOD of NB in this application depends on the wind regime, it is hard to estimate the exact cycle life.Therefore, we approximately estimate the cycle life of the NB based on the average DOD.From our simulation, the average DOD per charge/discharge cycle was about 0.3.Based on the result of [24], the total transferrable energy with DOD = 0.3 is about 82% of that with DOD = 1.0.In other words, the cycle life of the NB in this application is decreased by 18% comparing to the full-charge-discharge application.Considering that the full-charge-discharge is an ideal case, it is thought that the cycle life degradation in this application is not severe in practice.
reference case; the gap between the consecutive tuning constants was doubled in Set 2, while the gap was halved in Set 3. The other simulation settings, including the tuning constant of EDLC, were kept the same as those in Case 3. The results are shown in Figure 15 and the performance indices are summarized in Table 6.The maximum absolute power of NB and the loss of HESS were the smallest in Case 3, while the BHI was the smallest in Case 2. As shown in Figure 15a, the system power output and the SOC profile were almost the same for three simulation cases before 5600 s.Subsequently, the system output reference was the lowest in the result with Set 2, since the tuning constant of Set 2 is the smallest for low SOC levels.Therefore, the magnitude of charging power would be the maximum in the results with Set 2. As a result, the power loss of NB was the most increased.On the other hand, the recovery of the SOC level with Set 3 was the slowest.Furthermore, in the simulation with Set 3, the SOC level was less than the low operating limit, as shown in Figure 15b.Therefore, the value of the tuning constant should be selected carefully considering the tradeoff between the loss and the effectiveness of the NB usage.

Conclusions
This paper proposed a novel RWEMA of a wind-HESS system to denoise and flatten the wind power output.A real-time DWT was used to decompose the 1-s sampled wind power output into high-frequency and low-frequency components.The high-frequency components were used as a reference of the EDLC, while the low-frequency terms were used to calculate the reference of the NB.SOC control strategies of EDLC and NB were also proposed by using the tuning constant concept.In addition, 1-min and 10-min RRL requirements can be met by the proposed RWEMA.
The simulation models of the NB and EDLC energy storage system were developed in the RTDS/RSCAD software.A configuration interface was also developed to modify the simulation parameters of the model.The proposed RWEMA has been tested in real-time by using the RTDS hardware and software.The simulation results demonstrated the effectiveness of the proposed control algorithm in denoising and flattening wind power output, and managing the SOC level of storage.The results also showed that the required capacity ratings of storage used in RWEMA were smaller than those of the conventional SMA-based technique.Since the proposed approach uses a simple DWT-based structure without any prediction technique, it can be easily implemented in real-time applications.In order to move beyond the simulation level and into the hardware implementation, many practical issues and requirements still need to be considered, such as data acquisition, communication media and protocol, data management, and selection of processor.The proposed method will be implemented as an actual hardware controller and be tested with the real Wind-HESS system in the future.

Figure 3 .
Figure 3. Block diagram of the detailed dynamic model.

Figure 6 .
Figure 6.Flowchart of the complete real-time wavelet-based energy management algorithm (RWEMA).MWF: moving window function; DWT: discrete wavelet transform; and RRL: ramp rate limitation.

DtP
is basically used as a reference value for the EDLC inverter controller ( EDLC,ref t P

Figure 9 .
Figure 9. Active power output of wind turbine sampled at 1-s resolution: (a) Wind Pattern 1; and (b) Wind Pattern 2.

Figure 10 .
Figure 10.Simulation results for Case 1-without SOC control strategy: (a) total system power output; and (b) SOC level of EDLC and NB.
(a) Maximum Absolute Value of NB Power Output ( max NB P ): since the cost of the inverter is proportional to the power rating, smaller max NB P implies a lower installation cost.(b) Battery health index (BHI): defined in Equation ( Average power loss of energy storage ( avg ESS, loss

Figure 15 .
Figure 15.Simulation results for Case 4 with different tuning constant sets: (a) total system power output; and (b) SOC level of NB.
) is denoised and kept almost constant during the 10 min period:

Table 2 .
Tuning constant for the SOC control of EDLC and Ni-MH battery (NB).

Table 3 .
Test system parameters.

Table 4
summarizes a comparison between the two methods.For the Wind Pattern 1, 79%, and the BHI was 29.20% smaller than that of the SMA method.

Table 4 .
Comparison between SMA and RWEMA for Cases 2 and 3. BHI: battery health index.

Table 5 .
NB tuning constant sets used in Case 4.

Table 6 .
Impact of tuning constant to system performance.