A Comparatively Experimental Study on the Performance and Emission Characteristics of a Diesel Engine Fueled with Tung Oil-Based Biodiesel Blends (B10, B20, B50)

: In this paper, the performance and emission characteristics of a diesel engine were investigated with varying ratios of tung oil-based biodiesel blends (B10, B20, and B50) and neat diesel under different operating conditions. The experimental results showed that the addition of biodiesel blends had different effects on engine power and torque depending on the blend ratio. B10 displayed a slight increase in power and torque, which increased by 1.9% and 6.6%. At the same time, B20 and B50 showed declines slightly. The fuel consumption rate increased slightly with an increasing percentage of biodiesel added. In general, all the blends exhibited signiﬁcantly lower emissions of CO, NO X , HC, and smoke compared to neat diesel. B10 displayed the most notable reduction of CO emissions, with a 42.86% decrease at medium to high loads. NO X emissions of tung oil-based biodiesel blends were reduced at all load conditions except for B50. In addition, HC emissions were all reduced, especially for B20, which led to a 27.54% reduction at 50% load. Among all the tested blends, B50 showed the greatest decrease in smoke emissions of 38.05% compared to neat diesel at 2000 rpm. The research concluded that using biodiesel fuels from renewable resources, such as tung oil, presents a promising environmentally friendly alternative fuel option.


Introduction
As car ownership in China continues to rise rapidly, automobile exhaust emissions of harmful substances like CO, NO X , and PM have become the primary sources of urban air pollution, posing significant threats to human health. As we strive to enhance the quality of life and boost prosperity, one of the most significant challenges is meeting the ever-increasing demand for energy. Despite ongoing efforts to transition to alternative energy sources, it is apparent that fossil fuel-based internal combustion engines (ICEs) will remain the primary power source for energy and transportation in the foreseeable future [1][2][3]. However, as concerns about global environmental deterioration grow, the exhaust emissions from ICEs, such as carbon monoxide (CO), oxides of nitrogen (NO X ), carbon dioxide (CO 2 ), and hydrocarbons (HC) are increasingly subject to stringent regulations [4][5][6]. In order to promote the use of alternative fuels and address environmental concerns, major advanced and emerging economies have carried out a series of regulations [7][8][9]. As a green and environmentally friendly oxygenated fuel, biodiesel can effectively reduce the CO, NO X , and PM emissions of diesel engines. In addition, it can curb the increasing trend of automobile emission pollution as soon as possible and significantly improve the air quality of cities in China. Because of this, biodiesel has attracted more and more attention from scholars. in acid value (AV), KV, and CFPP was noted with increasing storage time. Nevertheless, the stability of the tung oil-based biodiesel could be improved by blending it with neat diesel, and a storage time of one month did not affect the ability of B20 or lower blends to meet the ASTM D7467 specification. Additionally, these blends were found to be more stable compared to pure tung oil biodiesel.
There are many studies on the combustion and emissions performance of different types of biological diesel, as well as a certain study of the feasibility and chemical properties of tung oil-based biological diesel. However, there is a lack of research on the emission characteristics of tung oil-based biodiesel. There is no literature report on the emission of engines burning tung oil-based biodiesel. Based on this, this study aims to fill this gap by investigating the performance and emission characteristics of an engine fueled with tung oil-based biodiesel under varying blend ratios. In the present experiment, an analysis of those was investigated using three different portions of tung oil-based biodiesel (10%, 20% and 50%) blended with neat diesel on a single-cylinder agricultural diesel engine. The test of speed characteristic, load characteristic, exhaust smoke and exhaust gas emissions were conducted on the test ZS1115 GM diesel engine. The results were studied and analyzed, and the potential for future use of tung oil-based biodiesel was explored. The study aims to provide valuable data to promote the use of biodiesel, which can assist in sustainable development and reduce emissions. By exploring the potential of this alternative fuel in diesel engines, this study contributes to the ongoing efforts to transition to alternative energy sources and address environmental concerns.

Experiments
This section is a description of experimental testing, including the physicochemical properties of biodiesel, experimental apparatus, and experimental setup. In addition, a comprehensive account of the initial and boundary conditions for laboratory experiments is provided.

Preparation and Properties of Biodiesel
The biodiesel used in this experiment is produced by the transesterification method, which is one of the better and most widely used biodiesel production methods. The transesterification method refers to the method of synthesizing biodiesel by transesterification reaction using various oils and fats and short-chain alcohols as raw materials, acids, alkalis, enzymes, etc., as catalysts or without using catalysts under supercritical conditions. A variety of low molecular weight alcohols can be used for transesterification reactions, such as methanol, ethanol, propanol, etc. However, the most commonly used is methanol due to its low cost and fuel properties, such as its polarity and short carbon chain, which can quickly react with fatty acid glycerides. In this paper, using tung oil as raw material and NaOH as the catalyst, biodiesel was prepared by transesterification reaction with methanol [31].
The main performance Indexes and chemical and physical properties of tung oilbased biodiesel were compared with neat diesel, as shown in Table 1. It shows the important characteristics of tung oil-based biodiesel and neat diesel. The following characteristics of biodiesel and neat diesel were determined in Zhonghe Energy Co., Ltd., Ningxiang, China.

Experimental Setup and Test Engine
The test was carried out on a 14.71 kW single-cylinder, four-stroke and water-cooled diesel engine. Table 2 shows the technical specifications of the engine. Figure 1 shows a schematic diagram of the experimental apparatus for diesel engines and instrumentation systems. To determine and measure the performance characteristics and emissions of biodiesel-fueled engines, diesel engines are equipped with the necessary measuring instruments. All instruments, such as a fuel consumption measuring device, exhaust gas analyzer, energy meter, ammeter, thermal load resistance, heat exchanger and digital thermometer, are equipped on the engine bench. Exhaust gas emission analyzers are used to measure emissions, such as unburned hydrocarbons (HC), nitrogen oxides (NOX), and carbon monoxide (CO). The measurement method of the exhaust gas analyzer and its measurement range, experimental percentage uncertainty, data measurement accuracy and further technical details of the en-   Exhaust gas emission analyzers are used to measure emissions, such as unburned hydrocarbons (HC), nitrogen oxides (NO X ), and carbon monoxide (CO). The measurement method of the exhaust gas analyzer and its measurement range, experimental percentage uncertainty, data measurement accuracy and further technical details of the engine and dynamometer are given in Table 3. To ensure the accuracy and reliability of the results obtained, three repeat tests were conducted. Each test was performed under the same conditions to minimize the impact of external factors on the measurements. The measurements were carried out using a range of high-precision instruments that were carefully calibrated before each experiment to minimize measurement errors. Table 3 provides detailed information about the measurement properties, including their specifications and uncertainty levels. The measuring instruments used in the experiments were chosen based on their suitability for the specific parameters being measured, and their accuracy and precision were verified through rigorous calibration procedures. By following strict measurement protocols and carefully selecting the appropriate measuring instruments, we aimed to minimize the potential sources of error and obtain reliable data. Overall, the experimental setup and measurement procedures were designed with utmost care to ensure that the results obtained were accurate and meaningful. The overall uncertainty of experiments was calculated using Equation (1) as follows [37]: The overall uncertainty of experiments.

Experimental Test Conditions
In order to guarantee the accuracy of experimental results, all laboratory experiments were conducted under identical operating conditions. Additionally, calibration was performed on all measuring instruments employed to record output data. The level of uncertainty for every device was analyzed and documented in Table 3. Furthermore, ambient conditions were monitored periodically both before and during experiments to ensure consistency throughout the tests. The test laboratory recorded the temperature, relative humidity, and density of the surrounding air. Sufficient warm-up time was given to the engine to ensure that it attained optimal operating temperatures, such as an engine oil temperature within the range of 77-84 • C. The test conditions of the following experiments are shown in the corresponding figures for each experiment in the results and discussion section.

Load Characteristics and External Characteristics
This experimental study investigated the speed characteristics, load characteristics, exhaust smoke, and gas pollutant emissions of different proportions of tung oil-based biodiesel (B10, B20, B50) and neat diesel fuel on the ZS1115GM diesel engine. The study also analyzed the influencing factors of these characteristics. Figures 2 and 3 are the economic power of tung oil-based biodiesel. The maximum power, fuel consumption, maximum torque and smoke of biodiesel with different proportions of biodiesel under different conditions were studied. Figure 2 shows the maximum power when the throttle is fully open. It can be seen from the diagram that the maximum power and torque of B20 are the smallest and B10 the largest. Compared with the power of neat diesel, B10 increased by 1.9%, and B20 and B50 decreased by 3.2% and 2.5%, respectively. When a small amount of tung oil-based biodiesel is added, ignition performance is improved due to its higher cetane number than pure diesel and a slight increase in oxygen content, thus increasing combustion efficiency. In addition, the diesel engine is a single-cylinder agricultural diesel engine that does not have a high-pressure common rail electric injection system, and combustion performance has a significant impact on this diesel engine. The ignition performance plays a dominant role in the economic performance of the diesel engine in small proportions. Therefore, B10 exhibited a slight increase in power and torque over neat diesel. Additionally, according to our research, there is only a slight increase in power and torque. However, when a large proportion of biodiesel is added, the calorific value, density, and viscosity of biodiesel significantly decrease, and these factors play a significant role in the performance, leading to a reduction in economic power. Consequently, the output power of the diesel engine slightly decreases after incorporating a significant amount of biodiesel [38].
Our results show that a small amount of blended tung oil-based biodiesel has no effect on the performance of older single-cylinder diesel engines without expensive fuel injection systems and can even be slightly improved, indicating the application scenarios of tung oil-based biodiesel.
The maximum torque when the speed is 2200 rpm and the power is 14.7 kW under the rated condition in Figure 3A, and the fuel consumption at the maximum torque are compared in Figure 3B as can be seen from the figure, the highest maximum torque is achieved when using B10. Compared to running with pure diesel, the engine fueled with B10 shows nearly 6.6% torque increment, and B10 increased nearly by 6.6%. However, Energies 2023, 16, 5577 7 of 15 maximum torque was reduced by 2.4% and 1.2% compared to the run with pure diesel if B20 and B50 were used. As can be seen, with the proportion of biodiesel increasing, the fuel consumption rate became higher. At high RPM, the brake thermal efficiency (BTE) of the engine will decrease due to poor air-fuel mixing and poor injection. In addition, the increased proportion of biodiesel, resulting in increased viscosity and density, will lead to increased fuel consumption. cussion section.

Load Characteristics and External Characteristics
This experimental study investigated the speed characteristics, load charact exhaust smoke, and gas pollutant emissions of different proportions of tung oil-ba odiesel (B10, B20, B50) and neat diesel fuel on the ZS1115GM diesel engine. The stu analyzed the influencing factors of these characteristics. Figures 2 and 3 are the ec power of tung oil-based biodiesel. The maximum power, fuel consumption, ma torque and smoke of biodiesel with different proportions of biodiesel under differe ditions were studied.    Figure 2 shows the maximum power when the throttle is fully open. It can from the diagram that the maximum power and torque of B20 are the smallest the largest. Compared with the power of neat diesel, B10 increased by 1.9%, and B50 decreased by 3.2% and 2.5%, respectively. When a small amount of tung biodiesel is added, ignition performance is improved due to its higher cetane num pure diesel and a slight increase in oxygen content, thus increasing combustion e In addition, the diesel engine is a single-cylinder agricultural diesel engine that The fuel consumption rate at 2200 rpm and 14.7 kW under rated conditions have been presented in Figure 4. As shown in the figure, the fuel consumption rate increases with the increased mixing ratio. The fuel consumption rate of B10 is 0.9 g/kW·h higher than that of neat diesel. The fuel consumption rate of B50 increases the most, which is close to 5.3%. Such behavior can be attributed to the high viscosity, high residual carbon value, high cetane number and low calorific value of biodiesel compared to those of petrochemical diesel [39]. The energy released by the same volume of diesel biodiesel blended fuel is lower than that of petrochemical diesel. At the same time, the thermal polymerization of biodiesel molecules leads to incomplete combustion, and more carbon deposits are formed in the diesel engine, which greatly increases the friction resistance and affects the performance of the diesel engine. The low volatility of biodiesel will affect spray evaporation, thus inhibiting mixing. Insufficient mixing results in the deterioration of combustion and instability of the diesel engine [40] and a reduction in the brake thermal efficiency (BTE) of diesel [41,42]. Therefore, the fuel consumption rate of biodiesel increases, and the economic performance decreases, especially when B50 is used as fuel.
Energies 2023, 16, x FOR PEER REVIEW high cetane number and low calorific value of biodiesel compared to those of petro ical diesel [39]. The energy released by the same volume of diesel biodiesel blend is lower than that of petrochemical diesel. At the same time, the thermal polymer of biodiesel molecules leads to incomplete combustion, and more carbon depo formed in the diesel engine, which greatly increases the friction resistance and affe performance of the diesel engine. The low volatility of biodiesel will affect spray ration, thus inhibiting mixing. Insufficient mixing results in the deterioration of co tion and instability of the diesel engine [40] and a reduction in the brake thermal effi (BTE) of diesel [41,42]. Therefore, the fuel consumption rate of biodiesel increases, a economic performance decreases, especially when B50 is used as fuel.

Emission Characteristic
The changes in gas phase exhaust pollutants and soot under different mixing and operation conditions are demonstrated in Figures 5-8. The CO emissions a speed and different rated loads are represented in Figure 5. It can be seen that B10 most obvious effect on reducing CO emissions under different loads. Diesel has th CO emissions at 100% rated load. CO emissions decrease sharply when the load r from 100% to 75%, while CO emissions from 75% to 10% rated load fluctuate little the engine operates at 100% load, the fuel consumption is significantly high. This dent from Figure 5, where the concentrated mixture's incomplete combustion du sufficient oxygen leads to a rapid surge in CO emissions. In particular, the CO-s emissions of B10 decreased by 42.86% at 75% load compared to neat diesel, while B50 increased by 60% at 25% load. The formation of CO is primarily influenced by concentration and serves as an indicator of complete combustion. At loads exceedin the high combustion temperature within the cylinder results from significant fue tion. At this time, the oxygen concentration is the main influencing factor of CO form The neat conventional fuel itself does not contain oxygen, while the oxygen-con characteristics of biodiesel itself improve the anoxic condition and reduce CO emi When the load is less than 20%, compared to that of diesel oil, the higher viscosity diesel [43,44] has caused difficult fuel atomization and incomplete combustion. crease in CO formation may be attributed to this factor [45].

Emission Characteristic
The changes in gas phase exhaust pollutants and soot under different mixing ratios and operation conditions are demonstrated in Figures 5-8. The CO emissions at rated speed and different rated loads are represented in Figure 5. It can be seen that B10 has the most obvious effect on reducing CO emissions under different loads. Diesel has the most CO emissions at 100% rated load. CO emissions decrease sharply when the load reduces from 100% to 75%, while CO emissions from 75% to 10% rated load fluctuate little. When the engine operates at 100% load, the fuel consumption is significantly high. This is evident from Figure 5, where the concentrated mixture's incomplete combustion due to insufficient oxygen leads to a rapid surge in CO emissions. In particular, the CO-specific emissions of B10 decreased by 42.86% at 75% load compared to neat diesel, while that of B50 increased by 60% at 25% load. The formation of CO is primarily influenced by oxygen concentration and serves as an indicator of complete combustion. At loads exceeding 20%, the high combustion temperature within the cylinder results from significant fuel injection. At this time, the oxygen concentration is the main influencing factor of CO formation. The neat conventional fuel itself does not contain oxygen, while the oxygen-containing characteristics of biodiesel itself improve the anoxic condition and reduce CO emissions. When the load is less than 20%, compared to that of diesel oil, the higher viscosity of biodiesel [43,44] has caused difficult fuel atomization and incomplete combustion. An increase in CO formation may be attributed to this factor [45].           Figure 6 demonstrates the NOX emissions under different rated loads at rated speed and the exhausted temperature at 100% load. Except for B50, increasing the tung oil mixing ratio results in lower NOX emission under the same engine load. Conversely, as the rated load decreases, NOX emissions also decrease. The emission curves when the load is 50% and 75% are shown in the figure, which can clearly see the above situation. However, B50 has higher NOX emissions than B20. The reason for the lower increase in oxygen content, when blended in a smaller proportion, lies in the inherent characteristics of biodiesel. Its high cetane number and low aromatic content naturally lead to a reduction in combustion temperature. This reduction in temperature leads to a decrease in NOX emissions. When adding a large proportion, the excess oxygen in the mixed fuel causes the atmosphere of NOX generation. In addition, due to the low calorific value of biodiesel, the combustion temperature of the higher proportion of mixed fuel may decrease, and the exhaust temperature of B50 increases, as shown in Figure 6B. The combined effect of these three factors may lead to an increase in NOX emissions of the higher proportion of mixed fuel [45][46][47]. Additionally, the air-fuel ratio under different loads is shown in Figure 7. When the diesel engine load increases, the fuel supply increases and the air-fuel ratio gradually decreases. As the air-fuel ratio decreases, NOX emissions increase. When the air-fuel ratio gradually increases, the air increases and the temperature in the cylinder decreases; thereby, NOX emissions decrease. Figure 8 illustrates the HC emission at rated speed and different rated loads. As the load decreases, HC emissions increase first and then decrease. When the load is 50%, HC emissions reach the maximum. When the load is 100%, HC emissions are minimal. The most obvious is that when the load is 50%, the HC emission of B20 is reduced by 27.54 % compared with neat diesel. In addition, HC-specific emissions of tung oil-based biodiesel blends were all reduced, especially for B20, which decreased by 21.90% at 10% load. However, overall, the B20 shows the best performance, with the most significant reduction in HC emissions. With a low blend ratio, the fuel-bonded oxygen improves mixture quality, thus more complete combustion and less HC and particulate emissions. Figure 9A exhibits the change in the smoke emission of tung oil-based biodiesel with different speeds of rated power. As can be seen from the figure, usually at 1200 r/min and 2200 r/min, smoke emission is the highest. B20 and B50 smoke emission for ordinary biodiesel has a significant reduction. In particular, Smoke emissions decreased with an increasing percentage of tung oil added, especially for B50, which decreased by 38.05% at 2000 rpm. Figure 9B shows the change of smoke of different biodiesel at the same speed. In rated working conditions, the smoke degree (FSU) decreases sequentially with the increase in the proportion of tung oil. B50 is reduced the most, reducing by nearly 41% at a  Figure 6 demonstrates the NO X emissions under different rated loads at rated speed and the exhausted temperature at 100% load. Except for B50, increasing the tung oil mixing ratio results in lower NO X emission under the same engine load. Conversely, as the rated load decreases, NO X emissions also decrease. The emission curves when the load is 50% and 75% are shown in the figure, which can clearly see the above situation. However, B50 has higher NO X emissions than B20. The reason for the lower increase in oxygen content, when blended in a smaller proportion, lies in the inherent characteristics of biodiesel. Its high cetane number and low aromatic content naturally lead to a reduction in combustion temperature. This reduction in temperature leads to a decrease in NO X emissions. When adding a large proportion, the excess oxygen in the mixed fuel causes the atmosphere of NO X generation. In addition, due to the low calorific value of biodiesel, the combustion temperature of the higher proportion of mixed fuel may decrease, and the exhaust temperature of B50 increases, as shown in Figure 6B. The combined effect of these three factors may lead to an increase in NO X emissions of the higher proportion of mixed fuel [45][46][47]. Additionally, the air-fuel ratio under different loads is shown in Figure 7. When the diesel engine load increases, the fuel supply increases and the air-fuel ratio gradually decreases. As the air-fuel ratio decreases, NO X emissions increase. When the air-fuel ratio gradually increases, the air increases and the temperature in the cylinder decreases; thereby, NO X emissions decrease. Figure 8 illustrates the HC emission at rated speed and different rated loads. As the load decreases, HC emissions increase first and then decrease. When the load is 50%, HC emissions reach the maximum. When the load is 100%, HC emissions are minimal. The most obvious is that when the load is 50%, the HC emission of B20 is reduced by 27.54 % compared with neat diesel. In addition, HC-specific emissions of tung oil-based biodiesel blends were all reduced, especially for B20, which decreased by 21.90% at 10% load. However, overall, the B20 shows the best performance, with the most significant reduction in HC emissions. With a low blend ratio, the fuel-bonded oxygen improves mixture quality, thus more complete combustion and less HC and particulate emissions. Figure 9A exhibits the change in the smoke emission of tung oil-based biodiesel with different speeds of rated power. As can be seen from the figure, usually at 1200 r/min and 2200 r/min, smoke emission is the highest. B20 and B50 smoke emission for ordinary biodiesel has a significant reduction. In particular, Smoke emissions decreased with an increasing percentage of tung oil added, especially for B50, which decreased by 38.05% at 2000 rpm. Figure 9B shows the change of smoke of different biodiesel at the same speed. In rated working conditions, the smoke degree (FSU) decreases sequentially with the increase in the proportion of tung oil. B50 is reduced the most, reducing by nearly 41%  Figure 10 shows the maximum smoke fro different biodiesels.  First of all, biodiesel contains fewer aromatic hydrocarbons. In general, the high the aromatic hydrocarbons contained in the fuel, the greater its smoke. The emission soot from biodiesel is lower compared to pure diesel because the smoke produced by fuel decreases with increasing amounts of alkanes. In addition, biodiesel is an oxygenat fuel (oxygen content of 10%); in the fuel combustion process, oxygen atoms play a role fuel. Especially in areas with high fuel concentration, after the fuel is oxygenated, the f can be burned more completely. It can reduce soot emissions. Additionally, smoke duces as the ambient temperature decreases [48][49][50][51].
Detailed comparative data can be seen in the following tables. Table 4 contains t emissions, specific emissions, specific emission reductions, and specific emission red tion rates of various exhaust gases under different rated loads. Tables 4 and 5 are a co parison of the economic power of different biodiesel (B20), which shows the power a  Figure 10 shows the maximum smoke from different biodiesels.  First of all, biodiesel contains fewer aromatic hydrocarbons. In general, the higher the aromatic hydrocarbons contained in the fuel, the greater its smoke. The emission of soot from biodiesel is lower compared to pure diesel because the smoke produced by the fuel decreases with increasing amounts of alkanes. In addition, biodiesel is an oxygenated fuel (oxygen content of 10%); in the fuel combustion process, oxygen atoms play a role in fuel. Especially in areas with high fuel concentration, after the fuel is oxygenated, the fuel can be burned more completely. It can reduce soot emissions. Additionally, smoke reduces as the ambient temperature decreases [48][49][50][51].
Detailed comparative data can be seen in the following tables. Table 4 contains the emissions, specific emissions, specific emission reductions, and specific emission reduction rates of various exhaust gases under different rated loads. Tables 4 and 5 are a comparison of the economic power of different biodiesel (B20), which shows the power and BSFC. First of all, biodiesel contains fewer aromatic hydrocarbons. In general, the higher the aromatic hydrocarbons contained in the fuel, the greater its smoke. The emission of soot from biodiesel is lower compared to pure diesel because the smoke produced by the fuel decreases with increasing amounts of alkanes. In addition, biodiesel is an oxygenated fuel (oxygen content of 10%); in the fuel combustion process, oxygen atoms play a role in fuel. Especially in areas with high fuel concentration, after the fuel is oxygenated, the fuel can be burned more completely. It can reduce soot emissions. Additionally, smoke reduces as the ambient temperature decreases [48][49][50][51].
Detailed comparative data can be seen in the following tables. Table 4 contains the emissions, specific emissions, specific emission reductions, and specific emission reduction rates of various exhaust gases under different rated loads. Tables 4 and 5 are a comparison of the economic power of different biodiesel (B20), which shows the power and BSFC.

Conclusions
Biodiesel was prepared from tung oil by conventional transesterification. The major physical and chemical properties of biodiesels and their combined blends were tested by ASTM standards. The performance and emission characteristics of 10%, 20% and 50% tung oil-based biodiesel blends were studied on a single-cylinder direct injection diesel engine. Based on the above research, the following conclusions can be drawn on it: (1) In terms of economy and power performance, compared with the use of neat diesel, the maximum power at full load is 16 kW for B10, which is 1.9% higher than neat diesel. In terms of torque, the B10 increased by almost 6.6%. However, the B20 and B50 decreased by 2.4% and 1.2%, respectively. The fuel consumption rate of B50 increases the most, and it increases by nearly 5.3%. This is mostly due to the calorific value of biodiesel, cetane number and other parameters that are quite different from diesel. (2) From the analysis of exhaust emission of the blends, it has been found that the NO X emissions blend decreases as increasing the proportion of tung oil-based except B50. B10 has the most obvious effect on reducing CO emissions at different rated loads. B20 shows the best performance with the most significant reduction in HC emissions. Biodiesel fuel reduces exhaust emissions, such as CO, HC, and NO X ; the CO-specific emissions of B10 decreased by 42.86% at 75% load compared to neat diesel, while that of B50 increased by 60% at 25% load. Compared to neat diesel, NO X -specific emissions of tung oil-based biodiesel blends were reduced at all load conditions except for B50. In addition, HC-specific emissions of tung oil-based biodiesel blends were all reduced, especially for B20 decreased by 22.15% at 10% load.
(3) When burning biodiesel, the exhaust smoke of biodiesel is significantly reduced. B50 is reduced the most, reducing by nearly 41%. This is because biodiesel contains fewer aromatic hydrocarbons, and biodiesel is an oxygen-containing fuel during fuel combustion.
The results show that if tung oil-based biodiesel is burned on the engine, the fuel injection system should be optimized to improve SFC and exhaust emissions. Further research could focus on enhancing the stability of the fuel, reducing NO X emissions and exploring uncontrolled emissions, such as smoke and particulate matter. This study contributes to the existing knowledge of the combustion and emission performance of biodiesel and provides valuable data to support the promotion and application of biodiesel in the context of environmental protection and emission reduction. However, it is important to note that the study was conducted under specific operating conditions, and further research is needed to evaluate the performance and emission characteristics of tung oil-based biodiesel blends under different engine conditions and long-term durability tests.
One of the main implications of our research is that tung oil-based biodiesel blends have the potential to significantly reduce the emissions of harmful pollutants, such as carbon dioxide, nitrogen oxides, and particulate matter. This is particularly important given the negative impact that these pollutants have on both human health and the environment. However, despite the many potential benefits of using biodiesel, there are also numerous barriers that need to be overcome in order to fully realize its potential. These include issues related to cost, infrastructure, and public perception. In order to address these challenges, it will be necessary to develop new policies and strategies that support the widespread adoption of biodiesel as a viable and sustainable alternative to traditional fossil fuels.
In conclusion, our research provides valuable insights into the potential of tung oilbased biodiesel blends to positively impact sustainable development in the energy and transportation sectors. By addressing the barriers to adoption and developing new policies and strategies, we can work towards creating a cleaner and more sustainable future for all. Acknowledgments: The authors appreciate the reviewers and the editor for their careful reading and many constructive comments and suggestions on improving the manuscript.

Conflicts of Interest:
The authors declare no conflict of interest.