Methods and Techniques for CO 2 Capture: Review of Potential Solutions and Applications in Modern Energy Technologies

: The paper presents and discusses modern methods and technologies of CO 2 capture (pre-combustion capture, post-combustion capture, and oxy-combustion capture) along with the principles of these methods and examples of existing and operating installations. The primary differences of the selected methods and technologies, with the possibility to apply them in new low-emission energy technologies, were presented. The following CO 2 capture methods: pre-combustion, post-combustion based on chemical absorption, physical separation, membrane separation, chemical looping combustion, calcium looping process, and oxy-combustion are discussed in the paper. Large-scale carbon capture utilization and storage (CCUS) facilities operating and under development are summarized. In 2021, 27 commercial CCUS facilities are currently under operation with a capture capacity of up to 40 Mt of CO 2 per year. If all projects are launched, the global CO 2 capture potential can be more than ca. 130–150 Mt/year of captured CO 2 . The most popular and developed indicators for comparing and assessing CO 2 emission, capture, avoiding, and cost connected with avoiding CO 2 emissions are also presented and described in the paper.


Introduction
With the increase in electricity consumption around the world, electricity demands are increasing every day.During electricity generation using energy technologies based on fossil fuels, the emission of harmful pollutants into the environment (gaseous, liquid, and solid) occurs as the emission of NOx, SOx, dust, CO 2 , and wastewater (e.g., from flue-gas treatment installations) [1][2][3].Last year, a great deal of effort in modern lowemission energy technologies was directed at activities leading to decreased gaseous pollutant emissions [4,5].The emission of carbon dioxide (CO 2 ), which is treated as one of the main reasons for global warming when fossil fuel is burned, cannot be avoided.Fossil-fueled power-production technology plays a significant role in contributing to the emission of greenhouse gases into the atmosphere.By reducing the emission of CO 2 into the atmosphere, and by switching to an alternative power generation with zero-emission, it is possible to prevent future catastrophic effects.The carbon capture utilization and storage (CCUS) methods and technologies are among the many ways to reduce CO 2 emissions.CCUS technologies aim to capture CO 2 from large industrial sources and store it in underground structures, or use it through conversion into useful products [6].All this is happening while emissions from the industrial and energy sectors are reduced, which makes this process one of the most current scientific research endeavors, while also presenting socio-economic challenges.The current fees related to CO 2 emissions in the European Union amount to over 50 EUR/tCO 2 [7], and there is an expected upward trend for coming years, forced by political declarations and treaties.
Reducing the use of fossil fuels by: improving the efficiency of energy conversion processes; reducing the demand for energy; using renewable (non-fossil fuel) energy sources, such as hydropower, wind, biomass, solar cells, and nuclear power; increasing the use of green hydrogen, which is produced by splitting water using electricity from renewable energy.

2.
Replace technologies using fossil fuels with a low carbon to hydrogen C/H 2 ratio by replacing coal and oil with gaseous fuels.

3.
Capturing CO 2 from fuel combustion in power plants and other industrial processes and storing it in appropriate geological structures, in exhausted or exploited gas or crude oil deposits (intensification of crude oil extraction, enhanced oil recovery (EOR)), or at the bottom of oceans.4.
Limiting deforestation processes and thus storing more CO 2 in biomass.
Carbon capture utilization and storage (CCUS) is a family of methods to reduce the emission of CO 2 from fossil-fueled power plants.The CCS can be coupled with Power Plants (PPs) and Combined Heat and Power Plants (CHPPs) to reduce the emission of CO2 in the flue gas.First-generation carbon capture technology had a lower efficiency in carbon capture, and was challenging to integrate with the complex structures of a power plant.With improved research and development, the second-and third-generation power plants using carbon capture technology showed improved efficiency and a low cost compared to first-generation CCS technology [9].The three different methods (pre-, post-, and oxyfuel combustion) for CO 2 capture and separation are under development.The oxyfuel combustion method is considered a promising solution from an energy-efficiency power-generation point of view.Authors have noted, that the energy penalty for the oxy-combustion method can be around 4%, in comparison to 8-12% for post-combustion methods [10].
The implementation of CCS in Europe is focused on two major factors, the development of power generation technology with carbon capture at a low cost and selling CO 2 at a high price to reimburse the cost of CO 2 transportation.In 2008, the European Parliament approved the "draft CCS directive", which aims to guide CO 2 geological storage.Due to public opposition from European Union countries for underground CO 2 storage, many countries allow only offshore storage projects [11].CCUS technologies are considered as crucial technologies for the European Commission, and are explicitly included in, e.g., the European Green Deal.Nowadays, more and more important projects at the industrial scale are funded by the Innovation Fund (https://ec.europa.eu/clima/eu-action/fundingclimate-action/innovation-fund/large-scale-projects_en,accessed on 20 January 2022).The International Energy Agency forecasts that CCS will contribute up to 21% of the reduction in CO 2 emissions into the atmosphere.Many countries, including Asian countries, still depend on coal-fired power production because of the low cost and reliability, and these cannot be wholly replaced with renewable energy systems.Some European countries, such as Poland, will depend on fossil-fuel power production for at least 30 more years.According to Polish Energy Policy, by the year 2050, electricity demand in Poland will be produced by renewable energy and future nuclear power projects.The use of coal for the next few years makes CCS technology inevitable [12].Carbon capture and storage is a method for capturing the concentrated CO 2 in flue gas from fossil-fueled power plants and store them in one place.There are three methods of CO 2 capture: pre-combustion carbon capture, post-combustion carbon capture, and the oxy-combustion carbon capture method.

•
Pre-combustion carbon capture occurs before the combustion process (through fuel gasification with oxygen, e.g., integrated IGCC coal gasification technology).

•
Post-combustion carbon capture occurs after the combustion process (capturing CO 2 from flue gas, e.g., using chemical absorption, physical adsorption, membrane separation, or the use of a chemical loop).
• Oxy-combustion carbon capture occurs after the combustion process in an oxygen atmosphere by separating CO2 generated during the oxy-combustion process, e.g., using an oxygen gas turbine.Oxygen atmosphere can be obtained by removing nitrogen from the air before the combustion process.
A diagram explaining the methods and techniques for CO 2 capture is shown in Figure 1.


Post-combustion carbon capture occurs after the combustion process (capturing from flue gas, e.g., using chemical absorption, physical adsorption, membrane s ration, or the use of a chemical loop).


Oxy-combustion carbon capture occurs after the combustion process in an oxy atmosphere by separating CO2 generated during the oxy-combustion process, using an oxygen gas turbine.Oxygen atmosphere can be obtained by removing trogen from the air before the combustion process.
A diagram explaining the methods and techniques for CO2 capture is shown in ure 1.In pre-combustion carbon capture, fuel is oxidized using a gasification proc which produces syngas with a composition of hydrogen (H2) and carbon monoxide (C The produced CO is converted into CO2, which is captured before combustion.Shija al. showed a comparison between power generation using coal gasification without bon capture, pre-combustion carbon capture, or chemical looping combat (CLC).Th sults showed that the overall efficiency of a power plant with pre-combustion carbon ture and CLC is reduced compared to a plant without CO2 capture.CO2 captured f fuel reduces the fuel volume sent to the turbine, reducing power generation.Howe due to environmental concerns, including a CO2 capture unit is unavoidable [13].Muk jee et al. compared each type of carbon capture method using an IGCC power plant w out CO2 capture.CLC was combined with a coal-fired IGCC, and analyses were formed based on electrical efficiency and carbon capture efficiency.The CLC and oxy combustion methods showed a value of around a 100% carbon capture rate compare pre-combustion CO2 capture, which achieved 94.8% CO2 capture.Another method of direct chemical looping combustion, where coal is fed directly to a boiler without ga cation, increased the electrical efficiency and achieved 100% CO2 capture.The results f the comparison of IGCC-CLC, pre-combustion, and oxyfuel combustion showed tha methods' energy penalties were 4.5%, 7.1%, and 9.1%, respectively [14].This article scribes the various carbon capture and storage methods and technology used in la scale units.The CO2 emission from a coal-fired ultra-supercritical power plant is ca lated.
The SO2 and NOx content in the flue gas has a higher chance of affecting the pu of CO2 during CO2 capture.The high purity of the CO2 stream is very important for r In pre-combustion carbon capture, fuel is oxidized using a gasification process, which produces syngas with a composition of hydrogen (H 2 ) and carbon monoxide (CO).The produced CO is converted into CO 2 , which is captured before combustion.Shijaz et al. showed a comparison between power generation using coal gasification without carbon capture, pre-combustion carbon capture, or chemical looping combat (CLC).The results showed that the overall efficiency of a power plant with pre-combustion carbon capture and CLC is reduced compared to a plant without CO 2 capture.CO 2 captured from fuel reduces the fuel volume sent to the turbine, reducing power generation.However, due to environmental concerns, including a CO 2 capture unit is unavoidable [13].Mukherjee et al. compared each type of carbon capture method using an IGCC power plant without CO 2 capture.CLC was combined with a coal-fired IGCC, and analyses were performed based on electrical efficiency and carbon capture efficiency.The CLC and oxyfuel combustion methods showed a value of around a 100% carbon capture rate compared to pre-combustion CO 2 capture, which achieved 94.8% CO 2 capture.Another method of coal direct chemical looping combustion, where coal is fed directly to a boiler without gasification, increased the electrical efficiency and achieved 100% CO 2 capture.The results from the comparison of IGCC-CLC, pre-combustion, and oxyfuel combustion showed that the methods' energy penalties were 4.5%, 7.1%, and 9.1%, respectively [14].This article describes the various carbon capture and storage methods and technology used in large-scale units.The CO 2 emission from a coal-fired ultra-supercritical power plant is calculated.
The SO 2 and NO x content in the flue gas has a higher chance of affecting the purity of CO 2 during CO 2 capture.The high purity of the CO 2 stream is very important for recycling methods.A pilot, dual-reflux VPSA unit, installed in the Łagisza Power plant in Poland, was installed for post-combustion CO 2 capture.Before the flue gas from the boiler is sent to the DR-VPSA unit, the flue gas is passed through an absorber, an adsorber, and a glycolic gas dehydration system to remove SO 2 and NO x .Activated carbon works effectively for the removal of SO 2 compared to the removal of NO x , which leads to a high-purity CO 2 [15].CO 2 emissions from the power sector are mainly caused by modern technologies, such as coal-fired, gas-fired, oil-fired, and combined cycle gas turbine (CCGT) power plants.Table 1 presents the CO 2 emissions and lower heating value depending on fossil fuel.From Table 1, it can be seen that CO 2 emissions depend on the content of the fuel.The higher the fuel content, the higher the CO 2 emissions will be.The increasing share of H 2 gives better properties to fossil fuels, taking into account the LHV and CO 2 emission levels.Natural gas consists mainly of CH 4 and is characterized by almost two times lower emissions than hard and lignite coal, and an almost two times larger LHV.This fact comes from gas fuel composition, where four atoms of hydrogen are inside the methane molecule of every carbon atom.Other modern power generating technologies, such as nuclear, renewable energy sources (RES), and hydrogen-based technologies, are less likely to produce emissions.A newly built CCGT power plant has CO 2 emissions of 350 kg CO2 /MWh without carbon capture, indicating the same emissions as a gas-fired power plant [16].In the case of an ultra-supercritical power plant fired with coal, CO 2 emissions up to 700 kgCO 2 /MWh can be produced.According to the type of coal-fired critical power plant used, CO 2 emissions range from 690 to 830 kgCO 2 /MWh [17].The use of fossil fuel in modern energy technology will continue until it is replaced with alternative technologies, such as renewable energies and power production without emission.Until these technologies are replaced with those without CO 2 emissions, CO 2 capture is unavoidable to reduce greenhouse gases and protect the environment.

Pre-Combustion CO 2 Capture
In this method, the fuel (coal, gas, biomass) is not completely combusted in the reactor, but is converted into a mixture of CO and H 2 in the reforming or gasification process.Subsequently, using the water-gas shift, CO 2 and H 2 are produced.Figure 2 shows a block diagram of the pre-combustion CO 2 capture method in a power plant.Pre-combustion capture is used, e.g., in an integrated gasification combined cycle (IGCC).Carbon dioxide is removed after the gasification process.An example of a typical process for power and heat generation in a gas turbine with pre-combustion capture is  Pre-combustion capture is used, e.g., in an integrated gasification combined cycle (IGCC).Carbon dioxide is removed after the gasification process.An example of a typical process for power and heat generation in a gas turbine with pre-combustion capture is shown in Figure 3. Pre-combustion capture is used, e.g., in an integrated gasification combined cycle (IGCC).Carbon dioxide is removed after the gasification process.An example of a typical process for power and heat generation in a gas turbine with pre-combustion capture is shown in Figure 3.In this process, steam and oxygen are provided to the gasifier to produce syngas enriched in hydrogen and carbon monoxide.Then, syngas is sent to a cyclone separator, where it is filtered to remove ash.After, the conversion of syngas and steam to CO2 and H2 occurs in the water-gas shift reactor.The received gas needs to be purified of sulfur in the desulfurization unit.Subsequently, CO2 is captured in the CO2 separator and is sent for storage or utilization.Received hydrogen is provided to the gas turbine as fuel [18].Pre-combustion methods are very effective in CO2 separation on the grounds of the high concentration of CO2 in fuel before combustion.On the other hand, these processes are expensive due to the need for a gasification unit.
Pre-combustion carbon capture uses physical and chemical methods to capture CO2 from processed syngas.Chemical absorbents, such as carbonates and physical solvents, such as polypropylene glycol and methanol, are commercially used in industries to capture CO2.The cost expenditure and energy consumption of carbon capture depend on the utilities and capture process.An effective solvent or absorbent pre-combustion carbon capture technology can achieve more than 90% CO2 capture, but, at the same time, reduces In this process, steam and oxygen are provided to the gasifier to produce syngas enriched in hydrogen and carbon monoxide.Then, syngas is sent to a cyclone separator, where it is filtered to remove ash.After, the conversion of syngas and steam to CO 2 and H 2 occurs in the water-gas shift reactor.The received gas needs to be purified of sulfur in the desulfurization unit.Subsequently, CO 2 is captured in the CO 2 separator and is sent for storage or utilization.Received hydrogen is provided to the gas turbine as fuel [18].Pre-combustion methods are very effective in CO 2 separation on the grounds of the high concentration of CO 2 in fuel before combustion.On the other hand, these processes are expensive due to the need for a gasification unit.
Pre-combustion carbon capture uses physical and chemical methods to capture CO 2 from processed syngas.Chemical absorbents, such as carbonates and physical solvents, such as polypropylene glycol and methanol, are commercially used in industries to capture CO 2 .The cost expenditure and energy consumption of carbon capture depend on the utilities and capture process.An effective solvent or absorbent pre-combustion carbon capture technology can achieve more than 90% CO 2 capture, but, at the same time, reduces plant efficiency [19].The calcium looping process is another method of pre-combustion CO 2 capture, where CO 2 capture is achieved effectively at a low cost.This method involves the sorption of CaO with CO 2 and the desorption of CaCO 3 to release CO 2 at an optimal temperature.This cycling process repeats multiple times, and waste heat from the gasifier is used to reduce the heat consumption of the CO 2 capture process.The CaL pre-combustion carbon capture method is highly effective.Low-cost and CO 2 capture are achieved by decreasing energy consumption [20].The pre-combustion carbon capture demo plant in Port Arthur, United States, has successfully captured 1 million tons of CO 2 since it started operations, without problems.This plant proved that, using the dual pressure swing adsorption (PSA) technology method, purification of hydrogen >99.9% and a high efficiency CO 2 capture can be achieved.When the streaming gas has a low pressure, hydrogen purification is performed and the tail gas is sent to undergo vacuum pressure swing adsorption (VPSA) to separate purified CO 2 .If the streaming gas has a high pressure, Energies 2022, 15, 887 6 of 21 CO 2 capture is achieved without VPSA first, and hydrogen purification is achieved from the exiting gas [21].

Post-Combustion CO 2 Capture
Post-combustion CO 2 capture methods are based on removing carbon dioxide from flue gas.The capture unit is placed after the purification systems, such as desulphurization, denitrogenation, and dedusting installations.decreasing energy consumption [20].The pre-combustion carbon capture demo plant in Port Arthur, United States, has successfully captured 1 million tons of CO2 since it started operations, without problems.This plant proved that, using the dual pressure swing adsorption (PSA) technology method, purification of hydrogen >99.9% and a high efficiency CO2 capture can be achieved.When the streaming gas has a low pressure, hydrogen purification is performed and the tail gas is sent to undergo vacuum pressure swing adsorption (VPSA) to separate purified CO2.If the streaming gas has a high pressure, CO2 capture is achieved without VPSA first, and hydrogen purification is achieved from the exiting gas [21].

Post-Combustion CO2 Capture
Post-combustion CO2 capture methods are based on removing carbon dioxide from flue gas.The capture unit is placed after the purification systems, such as desulphurization, denitrogenation, and dedusting installations.Figure 4 shows a general block diagram of the post-combustion capture technique.In existing conventional power units, post-combustion technologies are the most frequently considered [2,8]; nevertheless, there is one main barrier to using these methods.Since the partial pressure of CO2 in the flue gas is low (flue gas is under atmospheric pressure and the concentration of carbon dioxide is within 13-15%), the driving force for CO2 is also low [22].Post-combustion technologies can be divided up according to the type of process used for capturing carbon dioxide, as follows: (a) Absorption solvent-based methods Chemical absorption is the most recognizable method of CO2 capture.It relies on a reaction between carbon dioxide and a chemical solvent.Solvents that are usually used are alkanolamines, such as monoethanolamine (MEA), diethanolamine (DEA), or methyl diethanolamine (MDEA) in aqueous solution [23].A schematic diagram of chemical absorption is shown in Figure 5.The process takes place in two stages.In the first stage, the flue gas reacts with the solvent in the absorber to capture CO2.Subsequently, the rich loading solution is carried to the stripper to regenerate CO2 at elevated temperatures.The In existing conventional power units, post-combustion technologies are the most frequently considered [2,8]; nevertheless, there is one main barrier to using these methods.Since the partial pressure of CO 2 in the flue gas is low (flue gas is under atmospheric pressure and the concentration of carbon dioxide is within 13-15%), the driving force for CO 2 is also low [22].Post-combustion technologies can be divided up according to the type of process used for capturing carbon dioxide, as follows: (a) Absorption solvent-based methods Chemical absorption is the most recognizable method of CO 2 capture.It relies on a reaction between carbon dioxide and a chemical solvent.Solvents that are usually used are alkanolamines, such as monoethanolamine (MEA), diethanolamine (DEA), or methyl diethanolamine (MDEA) in aqueous solution [23].A schematic diagram of chemical absorption is shown in Figure 5.The process takes place in two stages.In the first stage, the flue gas reacts with the solvent in the absorber to capture CO 2 .Subsequently, the rich loading solution is carried to the stripper to regenerate CO 2 at elevated temperatures.The solution without CO 2 (lean-loading solution) is sent back to the absorber column.A high purity carbon dioxide stream from the desorber is transferred for compression and storage or utilization.The chemical absorption process has been used for a long time in the chemical industry.The typically used 30% MEA and MDEA solutions achieve a high process efficiency and a high degree of carbon dioxide purity [23].The chemical absorption method is a very energy-consuming process due to the need to supply a large amount of heat to the desorber.It is assumed that approx.30% (37%) of the heat supplied to the steam in the boiler should be directed to the CCS installation in the case of a steam unit fired with hard coal (lignite), depending on the absorber used (for ammonia, the amount of heat needed for regeneration is 22% for hard coal and 27% for lignite).Chemical absorption technologies are used in power plants fired with solid fuel, and they are the only ones that are commercially available.It is assessed that the amine method can capture approx.85-95% carbon dioxide included in flue gas with a purity above 99.95%[2].
method is a very energy-consuming process due to the need to supply a large amount of heat to the desorber.It is assumed that approx.30% (37%) of the heat supplied to the steam in the boiler should be directed to the CCS installation in the case of a steam unit fired with hard coal (lignite), depending on the absorber used (for ammonia, the amount of heat needed for regeneration is 22% for hard coal and 27% for lignite).Chemical absorption technologies are used in power plants fired with solid fuel, and they are the only ones that are commercially available.It is assessed that the amine method can capture approx.85-95% carbon dioxide included in flue gas with a purity above 99.95%[2].Nowadays, apart from conventional solvents (amine-based-MEA, DEA, ammonia, piperazine), there are other solvents developed for the CO2 capture process.Solvent blends offer the ability to improve absorption properties by combining types properly.Primary and secondary amines have high absorption rates, and tertiary amines are characterized by a high capacity [8].For example, blending MEA with a little PZ can improve the absorption rate (PZ is 50 times faster than MEA) [24].Another possibility is to use a solution of 2-amino-2-methyl1-propanol (AMP) promoted with PZ.Artanto et al. showed that a mixture of 25 wt% AMP and 5 wt% PZ can be a good substitution for MEA [25].Ionic liquids (ILs) are novel alternatives for amines.These low melting salts are comprised of a large organic cation and an arbitrary anion, which can be combined freely, obtaining a great variety of compound properties.ILs can physically or chemically absorb CO2, depending on pressure [8].A review [26] and articles [24,27] have presented deep insight into this technology.In the case of reducing energy consumption, there are new generation solvents-water-free solvents and biphasic solvents-that have been proposed.The presence of water in a solvent enhances the energy demand for the regeneration process.Novel water-free solvents, such as non-aqueous organic amine blends (methanol, ethylene glycol), aminosilicones, or amines with a superbase have been observed [24].In [28], Figure 5. Scheme of the post-combustion CO 2 capture method using a chemical absorption process (based on [22]).
Nowadays, apart from conventional solvents (amine-based-MEA, DEA, ammonia, piperazine), there are other solvents developed for the CO 2 capture process.Solvent blends offer the ability to improve absorption properties by combining types properly.Primary and secondary amines have high absorption rates, and tertiary amines are characterized by a high capacity [8].For example, blending MEA with a little PZ can improve the absorption rate (PZ is 50 times faster than MEA) [24].Another possibility is to use a solution of 2amino-2-methyl1-propanol (AMP) promoted with PZ.Artanto et al. showed that a mixture of 25 wt% AMP and 5 wt% PZ can be a good substitution for MEA [25].Ionic liquids (ILs) are novel alternatives for amines.These low melting salts are comprised of a large organic cation and an arbitrary anion, which can be combined freely, obtaining a great variety of compound properties.ILs can physically or chemically absorb CO 2 , depending on pressure [8].A review [26] and articles [24,27] have presented deep insight into this technology.In the case of reducing energy consumption, there are new generation solventswater-free solvents and biphasic solvents-that have been proposed.The presence of water in a solvent enhances the energy demand for the regeneration process.Novel waterfree solvents, such as non-aqueous organic amine blends (methanol, ethylene glycol), aminosilicones, or amines with a superbase have been observed [24].In [28], researchers showed that solvent mixtures based on ethylene glycol, used in the chemisorption process, can achieve CO 2 capture efficiencies of up to 95%.Deep eutectic solvents (DESs), such as choline chloride and ethylene glycol at a 1:2 mole ratio are getting more attention.They are fluids consisting of organic halide salts and metal salts or a hydrogen bond donor.DESs have similar properties to ILs, but they are cheaper and environmentally friendlier.According to [29], using DESs can decrease the vapor pressure of a solvent, achieve a lower effect of corrosion, and needs less energy in the regeneration process.
The physical absorption method is based on using a chemically inert solvent, which absorbs CO 2 physically.Absorption occurs in water or organic absorbers (methanol, Nmethyl-2-pyrrolidone, dimethyl ether).This method achieves the best results for low temperatures and high pressures of the separated gas.Therefore, it is used to capture CO 2 from the coal gasification process.In this method, there are distinguished processes, with the use of solvent such as Selexol TM , Rectisol TM , Ifpexol TM , Fluor TM , Purisol TM , Sulfinol TM , and Morphysorb TM [23,24,30].
(b) Adsorption-physical separation Adsorption is a process that uses a solid surface to remove carbon dioxide from a mixture.Physical separation relies on adsorption, absorption, and cryogenic separation methods.It can be physical (Van der Waals forces for adhesion CO 2 -physisorption) or chemical (covalent bonding between compounds-chemisorption) [31].Physical adsorption uses various porous materials (such as activated carbon, alumina, metallic oxides, or zeolites [6]) to absorb carbon dioxide.Activated carbons contain amorphous carbon, and it is low-cost material with the advantage of having a large surface area and the possibility of modifying its pore structure.However, the weak binding energy with carbon dioxide causes this material to need to be highly microporous to be useful for carbon capture [8].Zeolites (crystalline aluminosilicates) have good adsorption properties for CO 2 capture, but they are hydrophilic.The presence of water weakens these properties by reducing the strength of interactions between coupled compounds [26].A new approach is to use metal-organic frameworks (MOFs) in adsorption processes.MOFs consist of metal ions or ion clusters linked by organic ligands and bridges that create strong coordination bonds.On account of this, MOFs are characterized as having benefits such as ease of design and synthesis, a high porosity, and tailored pore properties [32].One of the other adsorption materials is silica.Silicas are non-carbonaceous substances with a large surface area and pore size, and they are highly mechanically stable.Mesoporous silica materials use amine-based substances for CO 2 capture [8,31].The methods of adsorption are as follows: pressure swing adsorption (PSA), temperature swing adsorption (TSA), vacuum swing adsorption (VSA), and pressure-temperature swing adsorption (PTSA).
(c) Membrane separation Figure 6 depicts the membrane separation process.In the first place, flue gas is directed to an absorber to cool to the operating temperature of the membrane.Subsequently, flue gas is transported to the membrane.This method uses a spiral wound, flat sheet, and hollow fiber modules [30].
Energies 2022, 15, x FOR PEER REVIEW 9 of 22 Figure 6.Scheme of the post-combustion CO2 capture method using a membrane separation process (based on [22]).
There are two types of membrane capture technology: gas separation membranes and gas absorption membranes.With a gas separation membrane, gas with CO2 is introduced at the high-pressure side of the membrane.Carbon dioxide is recovered at the lowpressure side.A solid microporous membrane is used to enable gas flow and absorption in the gas absorption system.This system has a high removal rate of CO2, on the grounds of minimization of flooding, foaming, channeling, and entrainment.The principles of both Figure 6.Scheme of the post-combustion CO 2 capture method using a membrane separation process (based on [22]).
There are two types of membrane capture technology: gas separation membranes and gas absorption membranes.With a gas separation membrane, gas with CO 2 is introduced at the high-pressure side of the membrane.Carbon dioxide is recovered at the low-pressure side.A solid microporous membrane is used to enable gas flow and absorption in the gas absorption system.This system has a high removal rate of CO 2 , on the grounds of minimization of flooding, foaming, channeling, and entrainment.The principles of both membrane systems are shown in Figure 7 [22,30].
Figure 6.Scheme of the post-combustion CO2 capture method using a membrane separation p (based on [22]).
There are two types of membrane capture technology: gas separation memb and gas absorption membranes.With a gas separation membrane, gas with CO2 is duced at the high-pressure side of the membrane.Carbon dioxide is recovered at the pressure side.A solid microporous membrane is used to enable gas flow and absor in the gas absorption system.This system has a high removal rate of CO2, on the gro of minimization of flooding, foaming, channeling, and entrainment.The principles o membrane systems are shown in Figure 7 [22,30].Membranes should characterize relevant properties for gas separation-prope meability and selectivity.There are three types of membrane materials: polymeric branes (organic), ceramic membranes (inorganic), and hybrid membranes [22].A meric membrane has a lower cost of production than the others with a relatively hig flux and it is mechanically stable [33].Nevertheless, it has generally low selec CO2/N2-less than 100, and it is supposed to be 200 [32].Ceramic membranes, espe zeolites and their derivatives, obtain high selectivities.However, the production ramic membranes is more difficult [22].Hybrid membranes (modified on the surf Membranes should characterize relevant properties for gas separation-proper permeability and selectivity.There are three types of membrane materials: polymeric membranes (organic), ceramic membranes (inorganic), and hybrid membranes [22].A polymeric membrane has a lower cost of production than the others with a relatively high gas flux and it is mechanically stable [33].Nevertheless, it has generally low selectivity CO 2 /N 2 -less than 100, and it is supposed to be 200 [32].Ceramic membranes, especially zeolites and their derivatives, obtain high selectivities.However, the production of ceramic membranes is more difficult [22].Hybrid membranes (modified on the surface of inorganic membranes) provide advantages of both membranes, polymeric and ceramic.They have the flexibility and low cost of production of a polymer and the high selectivity of an inorganic material [8,22].For post-combustion capture, commercially available polymeric membranes, such as PRISM, Polaris, PolyActive, PermSelect, and Medal, are introduced in [34].A new approach is to use metal-organic frameworks (MOFs) in the experimental stage.These offer many properties that are useful for membranes, such as large surface areas, adjustable pore sizes, and controllable pore-surface properties [32].

(d) Chemical looping combustion (CLC) and calcium looping process (CLP)
Chemical looping technology uses two reactors, an air reactor and a fuel reactor.These reactors typically circulate fluidized beds that are coupled for carrier transport.In the air reactor, oxidation of an "oxygen carrier", usually metal particles, such as iron, manganese, or copper, occurs with the oxygen from air.As a result of the reaction, metal oxides are formed.These compounds are carried to a second reactor, where they react with the fuel.Metal oxides are reduced during combustion, producing energy and flue gas as a stream of CO 2 and H 2 O.The flue gas can be condensed to receive pure CO 2 [35,36].
The calcium looping process is a type of chemical looping.The process (Figure 8) is based on a reversible reaction between calcium oxide and carbon dioxide.The reaction of bounding CaO and CO 2 is called carbonation, and takes place in the first reactor.Subsequently, the formed calcium carbonate in the carbonator is transported to the second Energies 2022, 15, 887 10 of 21 reactor, called a calciner, where the reversible reaction occurs and high purity CO 2 stream is produced (>95%).In the calciner, the heat needed for the reaction is generated by burning fuel in the oxygen atmosphere, and sometimes the CLC capture method is considered a kind of oxy-combustion method.The reactors (circulating fluidized bed (CFB)) are coupled to transport solid and cyclones separate solid and gaseous mass streams.Calcium looping technology has a few advantages.It uses a cheap sorbent (lime) and the flue gas is partially desulfurized.Moreover, the process uses fluidized beds, and this mature high-temperature technology can generate power [6,37].
ganese, or copper, occurs with the oxygen from air.As a result of the reaction, meta ides are formed.These compounds are carried to a second reactor, where they react the fuel.Metal oxides are reduced during combustion, producing energy and flue g a stream of CO2 and H2O.The flue gas can be condensed to receive pure CO2 [35,36] The calcium looping process is a type of chemical looping.The process (Figure based on a reversible reaction between calcium oxide and carbon dioxide.The reacti bounding CaO and CO2 is called carbonation, and takes place in the first reactor.Su quently, the formed calcium carbonate in the carbonator is transported to the secon actor, called a calciner, where the reversible reaction occurs and high purity CO2 st is produced (>95%).In the calciner, the heat needed for the reaction is generated by b ing fuel in the oxygen atmosphere, and sometimes the CLC capture method is consid a kind of oxy-combustion method.The reactors (circulating fluidized bed (CFB)) are pled to transport solid and cyclones separate solid and gaseous mass streams.Cal looping technology has a few advantages.It uses a cheap sorbent (lime) and the flu is partially desulfurized.Moreover, the process uses fluidized beds, and this mature h temperature technology can generate power [6,37].(e) Cryogenic method The cryogenic method of carbon capture technology uses liquefied natural gas (L to provide cold energy to capture CO2.Cryogenic CO2 capture is used in oxyfuel com tion technology as well as in post-combustion carbon capture technology to separate from flue gas.With cryogenic CO2 capture, it is possible to produce high purity CO2 o to 99.17%.This method includes a few processes, such as compression, expansion, s ration, and cooling.The cryogenic method is less preferred because of its high operat cost [38].The cryogenic method used in post-combustion carbon capture is carried using various methods [38,39].(e) Cryogenic method The cryogenic method of carbon capture technology uses liquefied natural gas (LNG) to provide cold energy to capture CO 2 .Cryogenic CO 2 capture is used in oxyfuel combustion technology as well as in post-combustion carbon capture technology to separate CO 2 from flue gas.With cryogenic CO 2 capture, it is possible to produce high purity CO 2 of up to 99.17%.This method includes a few processes, such as compression, expansion, separation, and cooling.The cryogenic method is less preferred because of its high operational cost [38].The cryogenic method used in post-combustion carbon capture is carried out using various methods [38,39].

(f) Application of absorption-based post-combustion capture method
The absorption-based post-combustion capture is the most widely used method due to its efficiency and lower energy consumption.Monoethanolamine (MEA), methyl diethanol amine (MDEA) and piperazine (PZ) are the most extensively used amine solvents in large-scale industries [40].There are many classified technologies used in adsorption and absorption, as well as in membrane separation.Chao et al. analyzed the challenges and compared the commercial use of PCC technology using solvents for absorbents, bed configurations for adsorption, and membrane processes.Among the adsorbent processes, temperature swing adsorption is very effective for both adsorptions, using solid and solvents, compared to pressure swing adsorption (PSA) and vacuum swing adsorption (VSA).TSA is more efficient than PSA and VSA, but it consumes a large amount of energy during regeneration.In the case of chemical absorption, MEA is the best and most used solvent for CO 2 capture.MEA shows a good absorption and desorption rate when mixed with other solvents as well.However, the solvent absorption process requires a high energy consumption for the regeneration of solvents, and solvent losses may occur due to evaporation and chemical degradation, leading to reduced absorption capacity [41].Lungkadee et al. showed simulation analyses of retrofitting a post-carbon capture unit with a 300 MW power plant.The amine-based PCC technology used MEA amine for the carbon capture process, and was estimated to cost less than 55 $/ton of CO 2 capture.The absorber and desorber used in this process were designed to have 90% CO 2 capture capacity and 30 wt% of MEA.About 63.075 kg/s of CO 2 was captured from flue gas at a flow rate of 458 kg/s with 15% CO 2 content [42].Another simulation analysis of natural gas combined cycle (NGCC) power plants with PZ solvent showed better performance when compared to that of MEA solvent.The use of 40 wt% PZ solvent showed significant improvements in capture efficiency, energy consumption, and capture cost compared to that of using 30 wt% MEA solvent.The lowest CO 2 capture cost was obtained at 34.65 $/ton of CO 2 using 40 wt% PZ solvent [43].Hadri et al. showed a comparison of 30 different amine solutions (30 wt%) used for post-combustion carbon capture.The amine solutions were analyzed using a solvent screening setup, where amine was passed at 1 bar pressure with a gas containing 15% CO 2, and CO 2 loading was measured.Compared to that of other amines, hexamethylenediamine had the highest CO 2 loading of 1.35 and triethanolamine had the lowest CO 2 loading of 0.39 [44].
(g) Converting CO 2 into value-added chemicals CO 2 can be utilized to satisfy the needs of various industries as fuels and chemicals or beverages and food [45].Technologies that allow to convert CO 2 into value-added chemicals are still being developed because of their economic and environmental benefits.In contrast to physical processes, the valence state of CO 2 changes [46].This process can be used to produce chemical feedstock (polymers, plastics, carbonates [47]), as well as energy carriers (methane, ethane, methanol, syngas).Among the chemical conversions, it is possible to distinguish thermochemical, electrochemical (photoelectrochemical [48]), and biological processes, where enzymes are used [49].Because of the high stability of CO 2 , there is a thermodynamic barrier in the CO 2 conversion process [50].A crucial component in most processes connected with converting CO 2 into value-added chemicals is hydrogen.It should be produced using renewable energy sources to maintain an environmentally friendly effect.

Oxy-Combustion CO 2 Capture
The exhaust gas from combustion in an oxygen-enriched atmosphere (oxy-combustion) consists mainly of carbon dioxide and water vapor (nitrogen content is minimized).From the condensation of water vapor, CO 2 separation is possible.The condensation temperature is higher than ambient conditions, except for very low partial pressures during the condensation process.The oxygen for combustion is produced using the air separation process, which gives an oxygen purity of about 95%.The general scheme for the process using the oxy-combustion method is presented in Figure 9.
Application of oxy-combustion technology mainly concerns solid fuel-fired boilers, including pulverized coal boilers (PCs) or circulating fluidized bed boilers (CFBs), but more and more consideration is being given to the possibility of using oxy-combustion in energy systems with gas turbines.In oxy-combustion technologies, low-temperature and high-temperature boilers can be distinguished.The combustion process in low-temperature boilers usually takes place in oxygen mixed with recirculated exhaust gases.The flame temperatures are similar to those of air-powered units.In the case of high-temperature boilers, the temperature can exceed 2400 • C.
The strengths of oxy-combustion are nitrogen oxide (NO x ) reduction, boiler dimension reductions, a simplified CO 2 capture method compared to other technologies, the possibility of applying in existing technologies, and less mass flow rate of exhaust gases (about 75% less compared to combustion in air).The weaknesses of oxy-combustion are the high material requirements because of the high temperatures, an efficiency decrease (oxygen production process is energy-consuming), and a high capital cost.
process, which gives an oxygen purity of about 95%.The general scheme for the process using the oxy-combustion method is presented in Figure 9. Application of oxy-combustion technology mainly concerns solid fuel-fired boilers, including pulverized coal boilers (PCs) or circulating fluidized bed boilers (CFBs), but more and more consideration is being given to the possibility of using oxy-combustion in energy systems with gas turbines.In oxy-combustion technologies, low-temperature and high-temperature boilers can be distinguished.The combustion process in low-temperature boilers usually takes place in oxygen mixed with recirculated exhaust gases.The flame temperatures are similar to those of air-powered units.In the case of high-temperature boilers, the temperature can exceed 2400 °C.
The strengths of oxy-combustion are nitrogen oxide (NOx) reduction, boiler dimension reductions, a simplified CO2 capture method compared to other technologies, the possibility of applying in existing technologies, and less mass flow rate of exhaust gases (about 75% less compared to combustion in air).The weaknesses of oxy-combustion are the high material requirements because of the high temperatures, an efficiency decrease (oxygen production process is energy-consuming), and a high capital cost.
Oxy-combustion methods are mainly used at the laboratory scale, and for pilot installations, among which are the Callide Power Station [51] and Compostilla Thermal Power [52].A 30 MWe experimental unit in the Callide Power Station started operation in 2012.The nominal flow of 98% pure oxygen, which was supplied to the boiler, was 19,200 mn 3 /h.Various types of fuel have been the object of investigation (Callide coal, Minerva coal, etc.).Daily production of CO2 based on cryogenic capture technology was 75 t.The unit was closed after a successful demonstration in 2016.A pilot power plant unit with CO2 capture, based on oxy-combustion technology, was developed as part of the OXYCFB 300 project at Compostilla Thermal Power.The CO2 capture installation was equipped with a circulating fluidized bed boiler with thermal power of 30 MWth, and a pulverized coal-fired boiler with thermal power of 20 MWth.The flue gas stream was 800 m 3 /h.The daily capacity of the separation process, which was carried out using the cryogenic method, was 3-5 tons of CO2.
The development of oxy-combustion technology is not only connected with solidfired fuel units.It also concerns systems equipped with gas turbines, where combustion in an oxygen-enriched atmosphere takes place.Within the framework of the project Negative CO2 Emission Gas Power Plant [53,54], the concept of a negative CO2 emission gas Oxy-combustion methods are mainly used at the laboratory scale, and for pilot installations, among which are the Callide Power Station [51] and Compostilla Thermal Power [52].A 30 MW e experimental unit in the Callide Power Station started operation in 2012.The nominal flow of 98% pure oxygen, which was supplied to the boiler, was 19,200 m n 3 /h.Various types of fuel have been the object of investigation (Callide coal, Minerva coal, etc.).Daily production of CO 2 based on cryogenic capture technology was 75 t.The unit was closed after a successful demonstration in 2016.A pilot power plant unit with CO 2 capture, based on oxy-combustion technology, was developed as part of the OXYCFB 300 project at Compostilla Thermal Power.The CO 2 capture installation was equipped with a circulating fluidized bed boiler with thermal power of 30 MW th , and a pulverized coal-fired boiler with thermal power of 20 MW th .The flue gas stream was 800 m 3 /h.The daily capacity of the separation process, which was carried out using the cryogenic method, was 3-5 tons of CO 2 .
The development of oxy-combustion technology is not only connected with solidfired fuel units.It also concerns systems equipped with gas turbines, where combustion in an oxygen-enriched atmosphere takes place.Within the framework of the project Negative CO 2 Emission Gas Power Plant [53,54], the concept of a negative CO 2 emission gas power plant based on oxy-combustion combined with CO 2 capture from flue gas was developed.Application of CO 2 neutral fuel, such as sewage sludge in combination with oxy-combustion and CO 2 capture, will allow negative emission levels [55].The CO 2 capture process will be possible, among other things, through the use of a prototype spray-ejector condenser (SEC).The main task of the SEC will be to condense the water vapor from the exhaust gases.
Among other CO 2 capture technologies, oxy-combustion carbon capture does not require many process modifications.Oxygen is used for the combustion process instead of air to eliminate the nitrogen content in flue gas, which leaves flue gas with carbon dioxide and water vapor as the major contents.This flue gas does not require high energy consumption for CO 2 separation.The boiler's temperature is controlled by again sending part of the flue gas (about 70%) to the boiler.The air separation unit (ASU), which separates oxygen from air, is the most energy-consuming part of the oxyfuel combustion process.An industrial-scale cryogenic ASU consumes up to 200-225 kWh/t on an industrial scale [56].To improve efficiency and CO 2 capture, oxyfuel combustion carbon capture is combined with moderate and intense low-oxygen dilution (MILD).MILD oxy-combustion carbon capture (MOFC) holds many benefits, such as improving the efficiency of the plant, improv-ing the purity of the CO 2 , and reducing energy consumption [12].The oxy-fuel combustion CCS technology used in the Allam cycle shows a higher efficiency of 55-59%, which is higher when compared to that of a combined cycle power plant with a carbon capture unit.In the Allam cycle, the heat generated from the ASU is sent to the regenerator to heat up the CO 2 to 400 • C, which is then reused in the combustion chamber, improving the cycle efficiency [57].

Indicators for CO 2 Emission Level Assessment
In order assess the CO 2 emission level and CO 2 capture, many variants of indicators, depending on what they want to present, can be used and have been presented [8,[58][59][60][61][62][63].The most popular indicators that allow evaluating CO 2 technologies are as follows: • Specific emission of carbon dioxide, eCO 2 (kg CO2 /kWh): where .
m CO 2 -mass flow rate of the emitted CO 2 , kg/s; N net -net power of electricity generation, kW.

•
Relative emissivity of carbon dioxide, e r CO 2 (kg CO2 /kWh): where e r CO 2 in (Equations ( 2)-( 4)) is defined as the amount of emitted CO where CCR (unitless) is defined as the mass flow rate of the captured CO 2 , .m CO 2 ,capt (t/h) divided by the generated mass flow rate of CO 2 , .m CO 2 ,gen (t/h).

•
CO 2 emission index, χ (kg CO2 /kJ): Equation ( 6) defines new factor, χ (kg CO2 /kJ), which is the amount of CO 2 mass generated (kg) to the heat input in the fuel (kJ).m CO 2,gen is the mass of generated CO 2 , kg; Q is the heat input by the fuel, kJ.

•
CO 2 captured (kg CO2 /kWh): The term CO 2 captured (kg CO2 /kWh), defined by Equations ( 7) and ( 8), refers to the amount of CO 2 captured (kg CO2 /kJ) per unit of main product of the plant (e.g., power in power plant, kWh); η p,CCS is the efficiency of the plant with capture; η cap is the efficiency of the CO 2 capture.

•
CO 2 emitted (kg CO2 /kWh): The term CO 2 emitted (kg CO2 /kWh) is specified as the amount of CO 2 emitted per main product of the plant (e.g., power in the power plant, kWh).

•
CO 2 avoided (kg CO2 /kWh): The indicator CO 2 avoided (-) evaluates the direct CO 2 emission reduction from the plant, taking into account the emissions related to the capture processes, e.g., steam generation, and the emissions of the flue gas.eCO 2re f is the specific emission from the reference plant (kg CO2 /kWh), and eCO 2 p,CCS is the specific emission from the plant with capture (kg CO2 /kWh).
The term CO 2 avoided can also be characterized by the following form: This parameter is specified as the net reduction of CO 2 emission per unit of net power output (kg CO2 /kWh) comparing with a reference power plant without CO 2 capture and compared to that of a similar power plant with CO 2 capture.η re f is the efficiency of the reference plant without capture, η p,CCS is the efficiency of the reference plant with CO 2 capture installation, and η cap is the efficiency of the CO 2 capture process.

•
Specific primary energy consumption for CO 2 avoided SPECCA (kWh/kgCO 2 ): The indicator from Equation ( 12) defines the amount of energy used to avoid 1 kg of emitted CO 2 (kWh/kg CO2 ).HR p,CCS and HR re f (kJ/kWh) are the heat rate of the plant with and without CO 2 capture, respectively.

•
Specific primary energy consumption cost for CO 2 avoided (€/kgCO 2 ): Equation ( 13) is defined as the product of the SPECCA index multiplied by the primary energy cost, (€/kgCO 2 ), where HR re f and HR p,CCS are the heat rates of the plant without and with CCS installation, respectively (kJ/kWh); eCO 2re f and eCO 2 p,CCS are the CO 2 emission rates in the plant without and with CCS installation, respectively (kg CO2 /kWh); EC is the primary energy cost (€/kWh).

•
Levelized costs of electricity (USD/MWh): The levelized costs of electricity (LCOE), according to IEA, indicates the economic costs of generic technology.It allows comparing technology over operating lifetimes at plantlevel unit costs, at different baseloads.Equation (11) calculates the average lifetime levelized costs based on the costs of construction, operation and maintenance, fuel, carbon emissions, and decommissioning and dismantling, where Capital t is the total capital construction costs in year (t), O&M t is the operation and maintenance costs in year t, Fuel t is the fuel costs in year t, Carbon t is thecarbon costs in year t, D t is the decommissioning and waste management costs in year t, MWh is the amount of the electricity produced annually (MWh), (1 + r) −t is the real discount rate corresponding to the cost of capital, and the subscript t means the year, when is a sale of production or takes place the cost disbursement.

Applications of CO 2 Capture Technologies on a Large-Industrial Scale
Carbon capture, utilization, and storage (CCUS) will have a key role in efforts that will lead the world to a net-zero CO 2 emission path.CCUS technologies will have to play an important role, alongside electrification, hydrogen technologies, and sustainable energy based on biofuels.It is the only group of technologies that directly contributes to a reduction in CO 2 in crucial sectors and CO 2 removal that cannot be avoided.Stronger climate and investment incentives are driving forces for CCUS technology.Since 2017, the rapid growth of newly announced integrated CCUS units has been observed (Figure 10).These are mainly located in the United States and Europe and in Australia, China, Korea, the Middle East, and New Zealand [6].If all projects are launched, the global CO 2 capture potential will more than triple to about 130-150 Mt CO2 /year of captured CO 2 (currently it is about 40 Mt CO2 /year), as shown in Figure 10.In 2021, 97 CCUS facilities were in early stages and announced, 66 were in advanced development and 5 were under construction [64].Currently, there are 27 CCUS facilities in the world with a capture capacity of up to 40 Mt CO2 per year [6,64].The total capacity of all CCUS installations developed since 1972, and the capacity of new installations built every year, are presented in Figure 11.Currently, there are 27 CCUS facilities in the world with a capture capacity of up to 40 Mt CO 2 per year [6,64].The total capacity of all CCUS installations developed since 1972, and the capacity of new installations built every year, are presented in Figure 11.Currently, there are 27 CCUS facilities in the world with a capture capacity of up to 40 Mt CO2 per year [6,64].The total capacity of all CCUS installations developed since 1972, and the capacity of new installations built every year, are presented in Figure 11.  2. Commercial large-scale is defined as a scale covering the capture of at least 0.8 Mt/year CO2 for coal-fired power stations and 0.4 Mt/year CO2 for other industrial facilities (including natural gas-fired power generation).Data presented in Some of these have been operating since the 1970s and 1980s when natural gas processing plants in Texas began capturing CO 2 and delivering it to local oil producers.The first large-scale CO 2 capture and injection project, with dedicated CO 2 storage and monitoring systems, was put into operation at the undersea Sleipner gas field in Norway [66,67] in 1965.Commercial large-scale operations in 2021 in terms of CO 2 capture facilities are presented in Table 2. Commercial large-scale is defined as a scale covering the capture of at least 0.8 Mt/year CO 2 for coal-fired power stations and 0.4 Mt/year CO 2 for other industrial facilities (including natural gas-fired power generation).Data presented in Figure 11

Conclusions
Growing energy demands are still observed, and a large part of energy is produced with the use of fossil fuels.The gaseous pollutant emissions from fossil fuel power plants include carbon dioxide, which is the major cause for the emission causing global warming and climate change.The Paris Agreement aims for sustainable energy with zero-emission by capturing CO 2 released into the atmosphere from anthropogenic activities.The International Energy Agency report in 2020 recommends that the global energy transition can be carried using renewable energy, bioenergy, green hydrogen, and CCUS to reduce emissions in large-scale industries.This paper presents developed methods and technologies for carbon dioxide capture.Crucial issues connected with the progress of contemporary global technologies based on pre-combustion, post-combustion, and oxy-combustion methods have been discussed.
Pre-combustion capture is connected with removing carbon compounds before introducing fuel into the combustion chamber.This method is mainly used in integrated gasification in combined cycle (IGCC) processes, and can achieve a high efficiency of CO 2 removal-more than 90% of CO 2 capture.
Post-combustion methods are the only solutions for existing coal-fired units.CO 2 capture from flue gases is based on chemical absorption, physical separation, membrane separation, cryogenic methods, and combustion in a chemical loop.MEA solvents are the most mature technology; however, research showed less energy consumption for ammonia and PZ-AMP solvent, which must be investigated more.
In oxy-combustion technologies, fuel is burnt in an oxygen-enriched atmosphere.Therefore, exhaust gases consist mainly of CO 2 and steam, which are then condensed and carbon dioxide is separated.Currently, oxy-combustion methods are used at the laboratory scale and in pilot installations.This technology has many advantages and opportunities for development (reduction of NO x , less amount of exhaust gases, does not require many process modifications, possibility to use CO 2 neutral fuel, and Allam cycle).
Different ways of reducing CO 2 , when the fossil fuels are used as the energy input, are presented in this paper:

•
In the case of fossil-fueled power plants, there is a need to use carbon capture utilization and storage methods to reduce CO 2 emissions, and, at the end, to minimize the impact of greenhouse gases on the environment.

•
Currently, there are 27 CCUS commercial facilities with which the global CO 2 capture potential is about 40 MtCO 2 /year, but this can increase by three times after launching announced CCUS units.

•
Based on the prepared review, it can be concluded that most of the operating, largescale, commercial CCUS facilities are connected with natural gas processing and use CO 2 to enhance oil recovery.
Reduction of CO 2 emissions in energy technologies, especially in high-power fossilfueled technologies, requires constant development in order to achieve relevant capacities.The indicators for CO 2 emission level assessment, as specific emissions of CO 2 , CCR, CO 2 avoided, or SPECCA, are helpful in the evaluation process of different developed technologies for CO 2 capture and were described in detail in this paper.

Figure 1 .
Figure 1.Methods and techniques of CO2 capture.

Figure 1 .
Figure 1.Methods and techniques of CO 2 capture.

Energies 2022 , 22 Figure 2 .
Figure 2. Block diagram of electricity generation heat production with the use of the pre-combustion CO2 capture method.

Figure 2 .
Figure 2. Block diagram of electricity generation heat production with the use of the pre-combustion CO 2 capture method.

Figure 2 .
Figure 2. Block diagram of electricity generation heat production with the use of the pre-combustion CO2 capture method.

Figure 3 .
Figure 3. Scheme of integrated gasification combined cycle (IGCC) for electricity generation using a gas turbine using the pre-combustion CO2 capture method.

Figure 3 .
Figure 3. Scheme of integrated gasification combined cycle (IGCC) for electricity generation using a gas turbine using the pre-combustion CO 2 capture method.
Figure 4 shows a general block diagram of the post-combustion capture technique.

Figure 4 .
Figure 4. Block diagram of electricity generation and heat production through the use of the postcombustion CO2 capture method.

Figure 4 .
Figure 4. Block diagram of electricity generation and heat production through the use of the postcombustion CO 2 capture method.

Figure 5 .
Figure5.Scheme of the post-combustion CO2 capture method using a chemical absorption process (based on[22]).

Figure 9 .
Figure 9. Block diagram of electricity generation heat production with the oxy-combustion CO2 capture method.

Figure 9 .
Figure 9. Block diagram of electricity generation heat production with the oxy-combustion CO 2 capture method.
include facilities that are out of service: that in Salah (Algeria) closed in 2011, Los Cabin Gas Plant (USA) closed in 2018, Kemper County IGCC Project (Canada) closed in 2017, and Petra Nova (USA) closed in 2020.
2 divided by heat input from the fuel (kg CO2 /kWh); or as the net efficiency of electricity production of the cycle, η net (η net =N net / multiplied by the specific CO 2 emission, eCO 2 (eCO 2 = . Q), .mCO2 /N net )..