Investigation of Biomass Integrated Air Gasiﬁcation Regenerative Gas Turbine Power Plants

: The results show that Wood Chips of Acacia Nilotica trees available in Sudan lands can be successfully used in the gasiﬁcation process and, on the same basis, as a bio-renewable energy resource. Simulation models were used to characterize the air gasiﬁcation process integrated with a Regenerative Gas Turbine Unit. The results revealed that at a moisture content of 12%, gasiﬁcation temperature of 1500 K, pressure of 20 bar, and air-like gasiﬁcation medium, the biomass gasiﬁer’s ﬂow rate is higher at higher syngas rates. The results veriﬁed that there is an optimum ER for each syngas rate, in which the slow growth of the ER revealed the maximum gasiﬁer biomass ﬂow rate. For ER growth at lower levels, the speciﬁc fuel consumption (SFC) of the RGT Unit declines sharply from the maximum value reached at 0.27 kg/kW · h at an ER of 5% to the minimum value reached at 0.80 kg/kW · h at an ER of 25% for the lowest gasiﬁcation temperature of 1000 K. Moreover, ER growths at low levels have a signiﬁcant effect on the RGT plant’s performance, leading to increased RGT thermal efﬁciency. The increase in the biomass moisture content led to a sharp decrease in the RGT thermal efﬁciency. The RGT thermal efﬁciency remains high at higher gasiﬁcation pressure. The results revealed that the syngas lower heating value remains high at lower produced syngas rates. At the optimum ER, the H 2 mole fraction depicted a value of 1.25%, 0.85% of CO, and 10.50% of CH 4 for a lower heating value of 38 MJ/kg syngas. It is shown that the gasiﬁcation air entered into the gasiﬁer decreases amid the increase in the biomass moisture content. At different syngas rates (3–10 kg/s) and optimum ER, the results predicted that the Wood Chip biomass ﬂow rates decrease when the gasiﬁer efﬁciency increases. The simulation model revealed that ER growths at lower levels have a signiﬁcant effect on increasing the power of the RGT plant.


Introduction
Agriculture is considered the driver force of income and livelihood in Sudan. This sector occupies between 60% and 80% of the population and is regarded as the engine for raising other economic zone, such as trade, industry, and transport [1,2].
In Sudan, biomass is a vital renewable energy source because the carbon in biomass is observed as part of the biological carbon cycle widely produced on the land [3]. Biomass is a biological substance that consists of forest, agricultural, and paper waste [4,5] and various organic materials [6]. Because of the absence of a power supply in the rustic population, the rural population principally relies on biomass as a wellspring of energy [1]. Just efficiency. The combined cycle [43,44], which combines a gas turbine and a steam turbine cycle, is a more-essential procedure for increasing the thermal efficiency of the power plant cycle [35,45,46]. This work aims to reinforce the understanding of a regenerative RGT as a thermal process utilizing the integration of the Biomass Gasification Unit at the combustor and applying similar design parameters to Khartoum North Station (GT,187 MW) in Sudan. The study pushes for establishing a qualified operational and conceptual design procedure and reviews for the Integrated Biomass Gasification for Regenerative Gas Turbine Unit "IBGRGT". The work also presents a preliminary strategy to identify the performance and evaluation criterion of the Gasification of Biomass Process utilizing the effect of various operating conditions.

Materials and Methods
Acacia Nilotica Wood Chips, available in Sudan with an average size of 1 × 2 × 3 cm, were used as a feedstock and experimentally characterized according to the standard literature data [47][48][49][50][51]. The wood chip samples were processed for proximate analysis to identify the moisture content, ash content, volatile, and fixed carbon using the ASTM Standards mentioned in our previously published studies [19,21,26]. To identify the carbon, hydrogen, nitrogen, and oxygen content, ultimate analysis was performed using a Perkin Elemental Analyzer. The data from both analyses are shown in Table 1. As per the proximate analysis, the sample showed higher moisture content and volatiles with low ash content. The sample showed higher carbon and oxygen content. To reveal the heating value of the sample, bomb calorimetry was used. The results include the measured higher heating value of the Nilotica Biomass, which was a value of 19,094.94 kJ/kg, via a Calorimeter setup. Air was used as a gasification agent. The gasification system considered in this study is the cross-draft gasifier.

Modeling of Components
A schematic of a regenerative gas turbine and Biomass Integrated Unit (BIGT) [3] with a syngas producer is shown in Figure 1. The system comprises a hot air-driven gas turbine, compressor, combustor, and regenerator beside the Gassifier Unit. By using the gasification of dry biomass, the gasifier produces syngas [3]. The biomass material will be fed to the gasifier [52] at surrounding conditions described briefly in Figure 1. Since air is the gasification medium, gasification occurs in compressed air and produces syngas that enters the combustion chamber. A thermodynamic equilibrium method [7] based on a stoichiometric approach according to the method of Jarungthammachote and Dutta [53] was used for modeling the gasifier. The syngas composition is predicted using this model at the gasifier's operational temperature and pressure. The global reaction of gasification can be written as [12,22,51]: All coefficients from x 1 to x 6 will be calculated using atomic balancing and equilibrium constant equations. The following are the steps to take [3,42]: The secondary gas-phase reactions can be derived by examining the equilibrium constant expression of the oxidation reactions [11] in the gasifier, which virtually approaches an equilibrium state. These are the reactions: The reactions described above [3] are known as the methanation and the gas-water shift reaction, and their equilibrium constants are as follows: Finally, the energy balance is applied for the calculation of the gasification temperature (T gasif ) as follows [54]: which is the formation enthalpy in kJ/kmol, its value in the reference state is zero for all chemical compositions, and the enthalpy difference between the given state and the reference state [3]. The RGT power plants comprise four parts: compressor, combustion chamber (CC), turbine, and generator. The integrated biomass regenerative combined cycle arrangement considered in Figure 1 demonstrates how to utilize the hot turbine exhaust gas. The fresh atmospheric air from the surroundings is filtered and drawn continuously into the circuit; the energy is added by fuel combustion in the chamber unit [35]. The combustion products are spread through the turbine [55] and consequently produce electrical work, while the rest of the exhaust gases are discharged into the Biomass Gasifier and Regenerator Units. The needed power output of the gasifier, Q (MWth), is an essential input parameter set by the client [17]. Based on this, the designer calculates the amount of fuel to feed into the gasifier and the amount of gasifying medium required. The volume flow rate of the product gas, Vg (Nm 3 /s), is calculated by subtracting its lower heating value, LHVg (MJ/Nm 3 ), from its ideal higher heating value, LHVg (MJ/Nm 3 ) [17].
The lower heating value (LHV) or net heating value can be determined from gas formation (y i ), according to [17]: The net heating value or higher heating value (HHV) can be determined from gas formation (y i ), according to [17]:  (14) To find the biomass feed rate, the following formula is used, in which M f , the needed power output, is divided by the LHV of the biomass (LHV bm ) and by the gasifier efficiency (η gef ) [17]: The following unified correlation for HHV is based on 15 existing correlations and 50 fuels, including liquid, coal, biomass, and gas, developed by Channiwala and Parikh [17].
The lower heating value (LHV) or net heating value can be determined from gas formation (yi), according to [17]: The net heating value or higher heating value (HHV) can be determined from gas formation (yi), according to [17]: To find the biomass feed rate, the following formula is used, in which Mf, the needed power output, is divided by the LHV of the biomass (LHVbm) and by the gasifier efficiency (ηgef) [17]: The percentages of carbon, hydrogen, sulfur, oxygen, nitrogen, and ash, as determined by a final analysis on a dry basis, are C, H, S, O, N, and ASH. A critical parameter is the theoretical air demand for the entire combustion of a unit mass of fuel, m th , called the stoichiometric air requirement. Equation (16) [15] shows how to calculate it: How to calculare the amount of air needed, M a , is shown below [17]: The gasification of a unit mass of biomass in an air-blown gasifier is calculated by multiplying it by another parameter, ER.
The air requirement of the gasifier, M fa , at a fuel feed rate of M f is the amount of actual air [17]: The equivalence ratio (ER) [17] is a crucial design parameter for gasifiers. The stoichiometric air-fuel ratio is the ratio of the actual air-fuel ratio to the stoichiometric air-fuel ratio. This word refers to conditions when there is a lack of oxygen, such as those seen in a gasifier [17]: EA denotes the excess air coefficient [17]. Fuel is gasified rather than combusted when the ER value is very below 1.0, which has a big impact on the quality of gas produced by a gasifier. A gasifier's oxygen requirements, an air supply, or air-separation equipment that removes oxygen from the air can be used to fulfil this need. [17] Gasification efficiency is measured in cold-gas efficiency or hot-gas efficiency [17]. The energy intake above the potential energy output is known as cold-gas efficiency. With an LHV of Qg, the efficiency of gasifying Mf kg of solid fuel to produce Mg kg of the product gas is given as [17]: where LHV f is the solid fuel's lower heating value (LHV). The hot-gas efficiency, abbreviated as η hg , is defined as [17]: T 0 is the fuel temperature entering the gasifier, and T f is the gas temperature at the gasifier egress or the burner's access [17]. Accordingly, the intake pressure at the compressor inlet was modeled with the following equation [16]: where the intake pressure drop (∆P intake ) was taken to be 0.005 bar, and the intake temperature was modeled as the ambient temperature [56]. The process on the temperature-entropy diagram [42] is represented in Figure 1. The compressor compression ratio (r P ) can be defined as [35,41]: where P 1 and P 2 are the compressor's inlet and outlet air pressure, respectively [18]. The isentropic outlet temperature leaving the compressor is modeled by the equation [35,57,58]: The specific heat ratio for air γ a was taken as 1.4 and was predicted at γ g = 1.3 for the gas. The isentropic efficiency of the compressor and turbine was taken to be in the range of 85% to 90%. The isentropic compressor efficiency is expressed by the equation [59,60]: where T 1 and T 2 are the compressor inlet and outlet air temperatures, respectively, and T 2s is the compressor isentropic outlet temperature. The specific work required to run the compressor work (W C ) is modeled with the following equation [60]: Additionally, the specific heat of air is taken as C P air = 1.005 kJ kgK . The specific heat of flue gas (C pg ) is given by [60]: From the energy balance, the combustion chamber equation is as follows [18,51]: where . m f is the fuel mass flow rate in (kg/s), . m a is the air mass flow rate (kg/s), LHV is the fuel's low heat value, T it is the turbine inlet temperature, C P f is the specific heat of fuel, and T f is the temperature of the fuel. The specific heat of the flue gas was modeled with C P g = 1.07 kJ/kg·K; efficiency was set at 95%, and a pressure drop of ∆P C,C = 0.4785 bar was set in the combustor. Accordingly, the efficiency of the combustor is modeled as [35]: The air-fuel ratio at the combustor was modeled according to the following equation [35]: where the total mass flow rate is given by [35]: The discharge gas of the turbine is predicted according to the equation [35]: where the actual outlet temperature leaving the turbine at isentropic conditions is modeled according to [35]: The regenerator effectiveness ε is modeled according to the equation [59]: where T 3 is the combustor inlet temperature. The shaft work produced from the turbine is calculated by the equation [35]: The network from the GT Unit is expressed by the equation [35,61]: The output power from the GT is expressed with the equation [35,60,61]: The mechanical (η Mech ) and generator (η Gen ) efficiencies were taken to be 92% and 95%, respectively.
The heat supplied is expressed with the equation [35]: The heat supplied (per kg. air) to the combustor was modeled according to the equation [35]: The GT efficiency is determined by the equation [35]: Accordingly, the heat rate (HR), which is defined as the spent heat to generate unit energy of electricity, is determined by the equation [35,62]: The specific fuel consumption (SFC) is determined by the equation [35]:

Results and Discussion
The gasification process was simulated using Acacia Nilotica Wood Chips biomass available in Sudan. A detailed energy analysis was derived from investigating the optimal design conditions of the system that integrates the Biomass Unit with the Regenerative Gas Turbine Power Plant. The work was executed with the Thermodynamics Engineering Equation Solver (EES) codes. The work investigated air as a gasification medium to produce syngas fuel for Wood Chips (Acacia Nilotica). Figure 2 depicts the effect of the equivalence ratio (ER) on the gasifier's biomass mass flow rate at different syngas rates (5-20 kg/s). As observed, at a moisture content of 12%, gasification temperature of 1500 K, pressure of 20 bar, and air-like gasification medium, the biomass gasifier's flow rate is higher at a higher syngas rate. The higher value of the biomass flow rate reached 35 kg/s of the wood chips at a yielded syngas rate of 20 kg/s. The results verified that there is an optimum ER for each syngas rate, in which the slow growth of the ER revealed the maximum gasifier's biomass mass flow rate. After that, the further increases in the ER showed a slow downtrend due to increasing combustion products, changes of syngas constituents amid CO 2 , water vapor, nitrogen, and a massive decrease in the lower heating value of the syngas. The point of inflection can be regarded as the point of the optimal design of the system to derive the required biomass rate for the necessary air gasification to produce the assigned syngas rates. The produced syngas composition varies with the amount of supplied air to the process. Important to note that increasing the biomass content leads to a sharp decrease in the gasifier's efficiency. The simulation results observed that an increase in the syngas rate revealed an increase in the required biomass rate for gasification. However, the quality of the produced gas depends mainly on the amount of qualified air to achieve the high energy content of the gasification products [63]. Figure 3 displays the relationship between biomass moisture content and the RGT thermal efficiency at different gasification pressures (5-20 bar). As observed, the increase in the biomass moisture content leads to a sharp decrease in the RGT thermal efficiency.  Important to note that increasing the biomass content leads to a sharp decrease in the gasifier's efficiency. The simulation results observed that an increase in the syngas rate revealed an increase in the required biomass rate for gasification. However, the quality of the produced gas depends mainly on the amount of qualified air to achieve the high energy content of the gasification products [63]. Figure 3 displays the relationship between biomass moisture content and the RGT thermal efficiency at different gasification pressures (5-20 bar). As observed, the increase in the biomass moisture content leads to a sharp decrease in the RGT thermal efficiency. Important to note that increasing the biomass content leads to a sharp decrease in the gasifier's efficiency. The simulation results observed that an increase in the syngas rate revealed an increase in the required biomass rate for gasification. However, the quality of the produced gas depends mainly on the amount of qualified air to achieve the high energy content of the gasification products [63]. Figure 3 displays the relationship between biomass moisture content and the RGT thermal efficiency at different gasification pressures (5-20 bar). As observed, the increase in the biomass moisture content leads to a sharp decrease in the RGT thermal efficiency.  At 200 K and a gasification temperature of 1500 K, the RGT thermal efficiency revealed a higher value of 62% at the lowest biomass moisture content of 10% and the lowest value of 61% at higher rates of moistures. The RGT thermal efficiency remains high at higher gasification pressure. Higher values of biomass moisture content led to the low energy content of the syngas, which yielded low values of RGT thermal efficiency. As the amount of moisture content decreases, higher amounts of water have to be evaporated [64]. Since the heat needed to vaporize this water is transferred from the syngas constituents at the gasifier outlet, the temperature's products decrease, thus lowering the energy content and the syngas' physical and chemical exergy [64].
Lowering the moisture content of the biomass entering the gasifier raises the efficiencies of both the RGT and the Gasifier Unit. Further removal of the moisture will increase the chemical exergy of the product gas, and the physical exergy will be slightly increased [64]. The exergetic efficiency of the gasification process [17] decreases with the moisture content increase. In addition, with the increase in the moisture content, the CO 2 and H 2 O production rate increases [65]. The increase in the gasification pressure has influenced the RGT thermal efficiency and the syngas LHV due to enhancement of the gasification reactions and the growth of the major constituents of the syngas product. Figure 4 shows the variation of the equivalence ratio (ER) with syngas lower heating value at different wood chips syngas rates (5-25 kg/s), at gasification pressure of 20 bar, the temperature of 1500 K, and moisture content of 12%. The profile exhibited an increase in the syngas LHV with the ER, till an optimum amount of the ER, subsequently the further increase in the ER has led to slow down the syngas LHV.
At 200 K and a gasification temperature of 1500 K, the RGT thermal efficiency revealed a higher value of 62% at the lowest biomass moisture content of 10% and the lowest value of 61% at higher rates of moistures. The RGT thermal efficiency remains high at higher gasification pressure. Higher values of biomass moisture content led to the low energy content of the syngas, which yielded low values of RGT thermal efficiency. As the amount of moisture content decreases, higher amounts of water have to be evaporated [64]. Since the heat needed to vaporize this water is transferred from the syngas constituents at the gasifier outlet, the temperature's products decrease, thus lowering the energy content and the syngas' physical and chemical exergy [64].
Lowering the moisture content of the biomass entering the gasifier raises the efficiencies of both the RGT and the Gasifier Unit. Further removal of the moisture will increase the chemical exergy of the product gas, and the physical exergy will be slightly increased [64]. The exergetic efficiency of the gasification process [17] decreases with the moisture content increase. In addition, with the increase in the moisture content, the CO2 and H2 O production rate increases [65]. The increase in the gasification pressure has influenced the RGT thermal efficiency and the syngas LHV due to enhancement of the gasification reactions and the growth of the major constituents of the syngas product. Figure 4 shows the variation of the equivalence ratio (ER) with syngas lower heating value at different wood chips syngas rates (5-25 kg/s), at gasification pressure of 20 bar, the temperature of 1500 K, and moisture content of 12%. The profile exhibited an increase in the syngas LHV with the ER, till an optimum amount of the ER, subsequently the further increase in the ER has led to slow down the syngas LHV. The results revealed that the syngas lower heating value remains high at lower produced syngas rates. This is attributed to the increase in the raw biomass materials, which influences increasing the irreversibilities sharply inside the gasifier, which causes a reduction in the gasifier efficiency. The calorific value of the produced syngas depends on the heating value of the consumed biomass [11]. The higher the biomass heating value, the higher the calorific value of the produced syngas. Tar content in the gasification product is always higher for fuel richer with ash [66]. The results observed that the amount of consumed biomass plays a significant role in the final syngas energy content.
The gradual increase in the biomass should have a certain limit since a small amount of the required air will result in incomplete gasification of the biomass and produce less syngas energy content. The effect of the equivalence ratio (ER) on the RGT thermal efficiency at different gasification temperatures is presented in Figure 5. As observed, the The results revealed that the syngas lower heating value remains high at lower produced syngas rates. This is attributed to the increase in the raw biomass materials, which influences increasing the irreversibilities sharply inside the gasifier, which causes a reduction in the gasifier efficiency. The calorific value of the produced syngas depends on the heating value of the consumed biomass [11]. The higher the biomass heating value, the higher the calorific value of the produced syngas. Tar content in the gasification product is always higher for fuel richer with ash [66]. The results observed that the amount of consumed biomass plays a significant role in the final syngas energy content.
The gradual increase in the biomass should have a certain limit since a small amount of the required air will result in incomplete gasification of the biomass and produce less syngas energy content. The effect of the equivalence ratio (ER) on the RGT thermal efficiency at different gasification temperatures is presented in Figure 5. As observed, the simulation results revealed an optimum ER in which a higher RGT thermal efficiency occurred; thereafter, the additional amount of ER led to a decline in the thermal efficiency of the RGT Unit gradually. ER growths at low values have a significant effect on the performance of the RGT and lead to an increase in the RGT thermal efficiency. The low, moderate, and optimum ERs produce a high amount of the required syngas constituents, which revealed high syngas energy content and improved efficiency. simulation results revealed an optimum ER in which a higher RGT thermal efficiency occurred; thereafter, the additional amount of ER led to a decline in the thermal efficiency of the RGT Unit gradually. ER growths at low values have a significant effect on the performance of the RGT and lead to an increase in the RGT thermal efficiency. The low, moderate, and optimum ERs produce a high amount of the required syngas constituents, which revealed high syngas energy content and improved efficiency. To some extent, the reduction in the temperature promotes the growth of CO and H2 concentrations and the decrease in the CH4 concentration in the syngas [67]. The increase in the temperature results in primary and secondary water-gas shift reactions, secondary cracking, and reforming of heavy hydrocarbons activity. Thus this results in increasing the concentration of the H2 in the syngas [54,68]. The activity of water gas shift reaction and Boudouard reactions will significantly increase due to temperature growth.
Consequently, the carbon reacts with CO and H2O vapor produces a lot of CO. However, the further temperature growth promotes combustion reactions and thus decreases of CH4 amount at the syngas [54,68] final products. Figure 6 presents the variation of the equivalence ratio (ER) and the percentage mole fractions of the syngas at a gasification temperature of 1500 K, pressure of 20 bar, regenerator effectiveness of 95%, gasifier efficiency of 95%, moisture content of 12%, and a produced amount of 5 kg/s syngas. The influence of the significant parameter, ER, is displayed and observed. To some extent, the reduction in the temperature promotes the growth of CO and H 2 concentrations and the decrease in the CH 4 concentration in the syngas [67]. The increase in the temperature results in primary and secondary water-gas shift reactions, secondary cracking, and reforming of heavy hydrocarbons activity. Thus this results in increasing the concentration of the H 2 in the syngas [54,68]. The activity of water gas shift reaction and Boudouard reactions will significantly increase due to temperature growth.
Consequently, the carbon reacts with CO and H 2 O vapor produces a lot of CO. However, the further temperature growth promotes combustion reactions and thus decreases of CH 4 amount at the syngas [54,68] final products. Figure 6 presents the variation of the equivalence ratio (ER) and the percentage mole fractions of the syngas at a gasification temperature of 1500 K, pressure of 20 bar, regenerator effectiveness of 95%, gasifier efficiency of 95%, moisture content of 12%, and a produced amount of 5 kg/s syngas. The influence of the significant parameter, ER, is displayed and observed.
Additionally, the RGT thermal efficiency remains high at lower gasification temperatures. The optimum ER can be regarded as the point of the optimal design of the system to identify the amount of the required air to produce qualified syngas constituents and achieve a higher RGT thermal efficiency. Many reasons promote the temperature decrease for the gasification process, such as the ash, moisture, and the conditions of the gasification reactions.
The simulation results verified an increase in the syngas mole fractions amid increasing the ER to an optimum ER amount. The trend predicted a slowdown among the further increase if the ER. The moisture content of 12% is considered low and was reflected in the composition of the final syngas product. Beyond the optimal point of the ER, a massive decrease in the syngas energy content and the growth of the oxidative combustion reactions are occurring. The N 2 and H 2 O vapor formation increase with the increase in the ER, while the formation of CO 2 , CH 4 , H 2, and CO exhibited decreases upon increasing the ER. At the optimum ER, the H 2 mole fraction depicted a value of 1.25%, 0.85% of CO, and 10.50% of CH 4 , for a lower heating value of 38 MJ/kg syngas. The highest value of the syngas composition is depicted by N 2 since air is the gasification medium. Although a higher syngas energy content is observed, the amount of N 2 in the produced gas could be reduced by using steam or oxygen as oxidizing agents [11]. Additionally, the RGT thermal efficiency remains high at lower gasification temperatures. The optimum ER can be regarded as the point of the optimal design of the system to identify the amount of the required air to produce qualified syngas constituents and achieve a higher RGT thermal efficiency. Many reasons promote the temperature decrease for the gasification process, such as the ash, moisture, and the conditions of the gasification reactions.
The simulation results verified an increase in the syngas mole fractions amid increasing the ER to an optimum ER amount. The trend predicted a slowdown among the further increase if the ER. The moisture content of 12% is considered low and was reflected in the composition of the final syngas product. Beyond the optimal point of the ER, a massive decrease in the syngas energy content and the growth of the oxidative combustion reactions are occurring. The N2 and H2O vapor formation increase with the increase in the ER, while the formation of CO2, CH4, H2, and CO exhibited decreases upon increasing the ER. At the optimum ER, the H2 mole fraction depicted a value of 1.25%, 0.85% of CO, and 10.50% of CH4, for a lower heating value of 38 MJ/kg syngas. The highest value of the syngas composition is depicted by N2 since air is the gasification medium. Although a higher syngas energy content is observed, the amount of N2 in the produced gas could be reduced by using steam or oxygen as oxidizing agents [11].
The influence of the biomass moisture content on the RGT actual gasification's airflow rate can be observed in Figure 7. It is shown that the gasification air entered into the gasifier decreases amid the increase in the biomass moisture content. The biomass moisture content affects the quality of the consumed biomass. At a constant ER and syngas rate, increases in moisture content led to a decrease in the energy content of the syngas and an increase in the amount and the demand of the biomass flow rates, thus influencing a lower demand for the required air for the complete gasification process. The influence of the biomass moisture content on the RGT actual gasification's airflow rate can be observed in Figure 7. It is shown that the gasification air entered into the gasifier decreases amid the increase in the biomass moisture content. The biomass moisture content affects the quality of the consumed biomass. At a constant ER and syngas rate, increases in moisture content led to a decrease in the energy content of the syngas and an increase in the amount and the demand of the biomass flow rates, thus influencing a lower demand for the required air for the complete gasification process.  Further reduction in the gasification's air amid increasing the biomass moisture content will diminish the gasification process and produce an unqualified syngas final product. In addition, the results demonstrate that increasing the gasification temperature has slowed down the amount of the actual air required for gasification. Literature data revealed that, as the initial moisture content increases, the gasification temperature slows down due to changes in the syngas composition and the effect of the water-gas shift, Boudouard, and combustion reactions [69][70][71]. Moreover, the influence of the gasification pressure resulted in an increase in the amount of the actual air required for gasification (see Figure 8) since the biomass flow rate is higher at a higher gasification pressure. With air used as a gasification medium, it was observed that the increase in the gasification pressure led to an acceleration of the reaction rate and the product's conversion of the gasification reactions. Figure 9 shows the influence of the gasifier efficiency on the bio- Further reduction in the gasification's air amid increasing the biomass moisture content will diminish the gasification process and produce an unqualified syngas final product. In addition, the results demonstrate that increasing the gasification temperature has slowed down the amount of the actual air required for gasification. Literature data revealed that, as the initial moisture content increases, the gasification temperature slows down due to changes in the syngas composition and the effect of the water-gas shift, Boudouard, and combustion reactions [69][70][71]. Moreover, the influence of the gasification pressure resulted in an increase in the amount of the actual air required for gasification (see Figure 8) since the biomass flow rate is higher at a higher gasification pressure. With air used as a gasification medium, it was observed that the increase in the gasification pressure led to an acceleration of the reaction rate and the product's conversion of the gasification reactions. Figure 9 shows the influence of the gasifier efficiency on the biomass flow rate for the gasification process. At different syngas rates (3-10 kg/s), an optimum ER of 35%, gasification temperature of 1500 K, pressure of 20 bar, and moisture content of 12%, the results predicted that the Acacia Nilotica Wood Chip biomass flow rate required for a complete gasification process decreases amid increases in gasifier efficiency. In addition, the demand for a higher biomass flow rate is attained at higher Wood Chip syngas rates. The irreversibilities of the gasifier are attributed to various factors during the gasification process, such as the quantity of the biomass flow rate, friction losses, pressure drops, releases of the high amount of gases, water corrosion, scale formation, the fusion of metals, tar and char formations, etc. In addition, results show that there is an optimum gasifier efficiency, in which the assigned biomass flow rate should be identified to minimize the possible source of irreversibilities at the gasification process.
As plotted in Figure 10, at different gasification temperatures (1000-1600 K), pressure of 20 bar, biomass moisture content of 12%, and syngas rate of 5 kg/s, the ER shows a significant impact on the specific fuel consumption (SFC) of the RGT power plant. With ER growth at lower levels, the specific fuel consumption (SFC) of the RGT Unit sharply declines from the maximum value of 0.27 kg/kW·hr at an ER of 5% to the minimum value of 0.80 kg/kW·hr at an ER of 25% for the lowest gasification temperature of 1000 K. The results show that there is an optimum ER for each gasification temperature that ensures minimizing the SFC of the RGT power plant. Beyond the optimum ER, the trends predicted an inflection point, which exhibited an increase in the SFC. This is attributed to the excess amount of air released, resulting in more combustion reactions, changing the syngas composition, and slowing down the syngas' lower heating value. The SFC of the RGT power plant reached 0.30 kg/kW·h at the higher ER of 95%. In addition, the results show that the SFC remains low at lower gasification temperatures. The influence of the ER on the RGT power plant at different syngas rates is shown in Figure 11. The simulation model revealed that ER growths at lower levels significantly affect the RGT power. The optimum ER delivered the highest RGT power, after which the syngas composition and combustion reaction will diminish the power due to a decrease in the LHV of the syngas fuel. At an ER of 5%, maximum power of 400 MW is reached at Acacia Nilotica Wood Chips' syngas rate of 20 kg/s, whereas minimum power is reached at 50 MW for a syngas rate of 5 kg/s.   As plotted in Figure 10, at different gasification temperatures (1000-1600 K), pressure of 20 bar, biomass moisture content of 12%, and syngas rate of 5 kg/s, the ER shows a significant impact on the specific fuel consumption (SFC) of the RGT power plant. With ER growth at lower levels, the specific fuel consumption (SFC) of the RGT Unit sharply declines from the maximum value of 0.27 kg/kW·hr at an ER of 5% to the minimum value of 0.80 kg/kW·hr at an ER of 25% for the lowest gasification temperature of 1000 K. The results show that there is an optimum ER for each gasification temperature that ensures minimizing the SFC of the RGT power plant. Beyond the optimum ER, the trends predicted an inflection point, which exhibited an increase in the SFC. This is attributed to the excess amount of air released, resulting in more combustion reactions, changing the syngas composition, and slowing down the syngas' lower heating value. The SFC of the RGT power plant reached 0.30 kg/kW·h at the higher ER of 95%. In addition, the results show that the SFC remains low at lower gasification temperatures. The influence of the ER on the RGT power plant at different syngas rates is shown in Figure 11. The simulation model revealed that ER growths at lower levels significantly affect the RGT power. The optimum ER delivered the highest RGT power, after which the syngas composition and combustion reaction will diminish the power due to a decrease in the LHV of the syngas fuel. At an ER of 5%, maximum power of 400 MW is reached at Acacia Nilotica Wood Chips' syngas rate of 20 kg/s, whereas minimum power is reached at 50 MW for a syngas rate of 5 kg/s. Figure 10. Variation of equivalence ratio with the specific fuel consumption at different gasification temperatures. Figure 11. Effect of the rquivalence ratio on the RGT Power at different Wood Chip syngas rates.

Conclusions
This work reviewed and investigated the integration of the Biomass Gasifier Unit with a Regenerative Gas Turbine power plant, including the effect of various parameters. Simulation models were used to characterize the gasification process of Acacia Nilotica that the SFC remains low at lower gasification temperatures. The influence of the ER on the RGT power plant at different syngas rates is shown in Figure 11. The simulation model revealed that ER growths at lower levels significantly affect the RGT power. The optimum ER delivered the highest RGT power, after which the syngas composition and combustion reaction will diminish the power due to a decrease in the LHV of the syngas fuel. At an ER of 5%, maximum power of 400 MW is reached at Acacia Nilotica Wood Chips' syngas rate of 20 kg/s, whereas minimum power is reached at 50 MW for a syngas rate of 5 kg/s. Figure 10. Variation of equivalence ratio with the specific fuel consumption at different gasification temperatures. Figure 11. Effect of the rquivalence ratio on the RGT Power at different Wood Chip syngas rates.

Conclusions
This work reviewed and investigated the integration of the Biomass Gasifier Unit with a Regenerative Gas Turbine power plant, including the effect of various parameters. Simulation models were used to characterize the gasification process of Acacia Nilotica Figure 11. Effect of the rquivalence ratio on the RGT Power at different Wood Chip syngas rates.

Conclusions
This work reviewed and investigated the integration of the Biomass Gasifier Unit with a Regenerative Gas Turbine power plant, including the effect of various parameters. Simulation models were used to characterize the gasification process of Acacia Nilotica Wood Chip biomass in Sudan. This type of biomass (Acacia Nilotica Wood) is of great interest due to its wide domestic uses and agricultural lands. A parametric analysis of the released syngas composition, actual gasifier air, temperature, pressure, LHV, moisture content, equivalence ratio, gasifier efficiency, thermal efficiency, power, and specific fuel consumption of the regenerative gas turbine power plant was carefully investigated to identify the optimal design points of the gasifier system and the working conditions of the RGT power unit using this type of biomass. With an average syngas LHV of 30,000 MJ/kg, the results revealed that such a type of biomass (Acacia Nilotica Wood Chips) could achieve high thermal efficiency and a valuable energy-saving process with the Regenerative Gas Turbine Unit.

Data Availability Statement:
The data used to support the findings of this study are included within the article.