The Optimal Conﬁguration of Wave Energy Conversions Respective to the Nearshore Wave Energy Potential

: Ocean energy is one potential renewable energy alternative to fossil fuels that has a more signiﬁcant power generation due to its better predictability and availability. In order to harness this source, wave energy converters (WECs) have been devised and used over the past several years to generate as much energy and power as is feasible. While it is possible to install these devices in both nearshore and offshore areas, nearshore sites are more appropriate places since more severe weather occurs offshore. Determining the optimal location might be challenging when dealing with sites along the coast since they often have varying capacities for energy production. Constructing wave farms requires determining the appropriate location for WECs, which may lead us to its correct and optimum design. The WEC size, shape, and layout are factors that must be considered for installing these devices. Therefore, this review aims to explain the methodologies, advancements, and effective hydrodynamic parameters that may be used to discover the optimal conﬁguration of WECs in nearshore locations using evolutionary algorithms (EAs). salinity biomass, and deep ocean geothermal


Introduction
The oil crisis of the 1970s sparked the current studies on wave energy harvesting, despite patents on this strategy from the late 18th century. The emphasis on producing power from renewable sources is a significant field of study, especially with more attention being paid to climate change and the increasing levels of CO 2 . The total potential wave power resource is estimated to be 2TW. According to the Renewable 2022 World Status Report [1], renewable energy sources account for 19.2% of the global energy consumption, traditional biomass (8.9%), and solar and wind power (10.3%) following fossil fuel usage (78.3%). The gap between the market for renewable energy and the consumption of fossil fuels may soon be closed if we consider recent improvements in the renewable energy sector. The global market for alternative energy sources increased from 85 GW in 2004 to 560 GW in 2013 (excluding hydropower) [2][3][4]. With an increase from 48 to 318 GW, the wind industry took the lead in the sector. A number of variables, such as governmental backing, financial incentives, and falling technological prices that made renewable energy affordable, contributed to the revolution in this renewable industry.
The capacity of the global ocean's sources is immense, considering the wide range of available marine natural resources and massive sea surfaces. Waves, tidal and ocean currents, ocean thermal energy, salinity gradients, marine biomass, and deep ocean geothermal by the analytical approximation, such as the point absorber approximation. So far, most research on array layouts has been on the arrays of identical buoys, for which the analytical approximation still provides a high degree of accuracy. Finding the best configuration for a flap-type WEC array has also been performed using machine learning techniques, for example, by Sarkar et al. (2016) [42].
It is essential to consider the size and shape of the WEC devices, in addition to the spacing distances while planning the layout of the array. With arrays of two, three, and four buoys and four different random arrangement geometries, Ringwood and Korde (2016) [43] investigated the effect of the variable separation distance of each device. When the proportion of control and separation was used, the q-factor increased by around 40%. In a recent paper, Goteman (2017) [44] created an enlarged multiple scattering approach that allows for varying device sizes while assuming a cylindrical device. Recently, in 2019, Esmaeilzadeh and Alam [45] performed the GA optimization of a single submerged absorber plate, using the Fourier decomposition of plane geometry to parametrize the contour of the planar.
Current research on WEC arrays solely addresses the array power development, which is not conducive to real-life systems and prohibits their implementation by offshore energy providers [34,46,47]. Furthermore, the costs associated with WEC arrays are not well known at this early stage of development. Any WEC array optimization system must include an updatable cost model that can be adjusted when new data becomes available and the accuracy is improved.
Most studies on WEC array layouts include the impact of the individual devices on their surroundings, a key takeaway from the wind energy sector. The WEC interactions may boost an array's energy production, which is in contrast to wind turbines, wherein the surrounding devices can diminish the output power of the nearby turbines [48,49]. The present array optimization effort is concentrated on increasing the interaction factor, q, above 1 to show that the array's power output is larger than the generated power of a similar number of devices operating independently. Babarit [41,50,51] studied the interaction between the single devices and arrays, discovering that although the beneficial interaction factors are obtained in regular waves, this potential is constrained by the incorporation of irregular waves. The capability for the destructive interaction between the components in tight formations has also been investigated. According to Weller et al. (2010) [52], the number of beneficial proximity-based interactions between devices decreases as the significant wave height increases. As a consequence of the interaction between the devices, the masking leads the triangular-shaped arrays to obtain a greater value of q, than the squared-based forms, as stated by Borgarino et al. (2011) [51]. Goteman et al. (2015) [53] considered that using an array with many devices is better than installing individual devices. They found that arrays are essential for reducing the power output fluctuation and that grouping the point absorber-type systems inside an array will help. Wu et al. (2016) [54] enhanced their optimization of a submerged WEC with a threetether in array formation, using an EA and a covariance matrix adaptation evolutionary algorithm (CMA-EA). The enhanced optimization for this device class and the operating frequency was achieved via an interactive factor. Ruiz et al. (2017) [55] employed a CMAevolutionary strategy (ES) and a metamodel algorithm (MM) to evaluate the calculation overhead and efficacy. Despite the MM's fast convergence, it was determined to be inaccurate. The MM could only be helpful as a first step before moving on to a more refined approach. Optimizing a WEC array with varying device diameters and grid spacing was also explored by Giassi et al. (2017) [56], who reported that modifying a device's diameter mainly impacts its cost, not its ability to generate electricity. However, the generated power is quite sensitive to even small changes in mass.
As a further step toward optimizing energy production, a WEC's layout should be determined by the site where it will inevitably be installed. If you want a certain WEC to function as efficiently as possible, you may tweak its design by changing its shape or configuration. Therefore, the WECs should maximize their power output as much as possible throughout the design process. Recently, structural optimization methods have been used to improve ships' seakeeping and reduce their dynamic reaction while at rest. Numerous computational optimization approaches for designing offshore structure hulls have been developed by Clauss (1996) [57] and Birk (2009) [58], who focused on different types of structures, such as caisson and minimum-downtime semisubmersibles, tension-leg platforms, and semisubmersibles supported by gravity bases. Elchahal et al. (2007) [59] considered the structure's density distribution when designing the optimal interior geometry of the floating breakwaters and examined a case study of a breakwater being built in a port located some distance from the water's edge.
With the recent rise in the popularity of wave power, designers have sought to enhance the efficiency of their constructions by refining parts or completely renovating the shapes of their structures. For instance, Kramer and Frigaard [60] examined the direction and angle of the wave reflectors on the wave dragon (WD) to enhance the absorbed wave energy. In order to investigate the hydraulic modeling of a heaving WEC planned for the Belgian coast of the North Sea, Vantorre et al. (2004) [61] analyzed several configurations. The buoy shape was optimized by Alves et al. (2007) [62] for a WEC that operated largely in the heave motion, using a submerged buoy and a surface-piercing buoy. The present research examines a similar technique to the analysis, which sets a maximum stroke for the PTO mechanism to preserve more power. The SEAREV WEC, a rotating point absorber, was designed using a technique described by Ruellan et al. (2010) [63] in their article. The efficiency and power production for several kinds of WECs were calculated by Babarit et al. (2012) [64], using the scatter plot of data collected at various places. By optimizing the WEC design, McCabe (2013) [65] employed a genetic algorithm to enhance the wave energy extraction of a WEC that works in the surge motion. The program evaluates each shape in a wave climate for the best design. Kurniawan and Maon (2012) [66,67] investigated the potential for optimizing the geometric layout of both the submerged and the surface-penetrating wave absorbers that oscillate around a single axis and have a very basic cross-section. Their study proposed a multi-objective optimization approach to achieve the maximum power absorption.
This paper reviews past studies on optimizing the WEC systems, based on their geometry, layout, PTO system, optimal location, and maximizing wave energy extraction. Purposefully, the wave energy characteristics in nearshore spots and the WEC mechanism are first surveyed in Section 2. The different wave energy conversions have been introduced and demonstrated in recent studies, which were analyzed recently in various research programs. The various PTO mechanisms of wave energy conversions are presented to better understand the devices' dynamics. Further, the hydrodynamic interaction between the multiple devices is examined mathematically for the exact modeling of the layout designs. Section 3 discusses the previously developed optimization algorithms developed, as well as the advantage of some investigations. Section 4 summarizes the reviews, focusing on the recent advancements in WEC design.

Wave Energy Characteristics
In recent years, renewable energy sources have been hailed for their potential to lessen the environmental damage caused by the extraction of fossil fuels. In particular, Glendenning (1977) [68] reported that wave energy is blossoming into a viable alternative power source and should be taken into account, due to its greater energy density and reliability than other sources. In order to make the most of this resource and to maximize energy harvesting, it is important to thoroughly study the temporal and spatial wave changes on the nearshore, as suggested by Neil and Hashemi (2013) [69]. Over the last several years, many wave resource evaluations in various coastal regions across the globe have been conducted using the established approaches, such as the numerical modeling of the nearshore wave conditions [13,[70][71][72][73].
WECs are designed to operate in certain wave climates, and the peculiarities of the sea states also affect how much power they can produce [74,75]. Therefore, the differences in the power range of WECs, based on the wave conditions should be evaluated along with the available energy resource to select the best locations for a wave energy plant. However, the majority of the analyses of wave energy resources are restricted to assessing the wave energy resources in a specific coastal region and identifying the sites with the maximum transformation [76,77]. In light of these considerations, the innovative approaches for the wave energy evaluation must be created in order to pinpoint more precisely the locations with the most significant potential for collecting wave energy.
The different hydrodynamic modeling methods, such as Delft3D-Wave [78], XBeach [79], WaveWatch III [80], and the standalone Simulating WAve Nearshore (SWAN) [81][82][83], are well-verified wind-wave models that may be used to analyze the wave energy resource and identify the nearshore hotspots. The best locations for harvesting wave energy are those where the wave energy is concentrated due to the combined effects of refraction and shoaling. The model inputs include offshore wave characteristics collected at a wave buoy and coastal bathymetry. The nearshore wave simulations using the SWAN model have been performed for some time and are anticipated to improve further.
The Delft University of Technology developed the spectral model SWAN [83], based on third-generation wind-wave modeling, which forecasts the wave characteristics in shallow water. The wave action balancing equation is solved by SWAN using sources and sinks as follows: ∂N ∂t where N = N(σ, θ; x, y, t) denotes the action density; σ is the relative radian frequency; θ is the wave direction; x and y are the space variables; t is the time; c g,x , c g,y , c θ and c σ are the group velocities in the geographical space and in the spectral space (σ, θ), respectively. S tot = S tot (σ, θ; x, y, t) is the sum of the physical processes of the wave energy generation, dissipation, and redistribution: The parameters of Equation (2) are graphically illustrated in Figure 1.

Wave Energy Converter Types
The first WECs were installed in 1973 by Salter [84], who investigated the feasibility of wave power.
The amount of literature in this area has grown exponentially since the turn of the century. At present, there are at least six widely recognized categories of conversions, each of which is based on a different combination of factors, including the installation site, the PTO system type, the working regulations, whether the conversion is floating or sub-

Wave Energy Converter Types
The first WECs were installed in 1973 by Salter [84], who investigated the feasibility of wave power.
The amount of literature in this area has grown exponentially since the turn of the century. At present, there are at least six widely recognized categories of conversions, each of which is based on a different combination of factors, including the installation site, the PTO system type, the working regulations, whether the conversion is floating or submerged, and the number of degrees of freedom (DOFs) it possesses. These devices are categorized into different types, such as floating, fully submerged, partly submerged, and devices located on the sea floor. Six DOFs can be broken down into two sections. The first component includes the translational movement, such as heave, sway, and surge, while the second part carries the rotational degrees, such as roll, pitch, and yaw DOFs. WECs may be categorized based on the number of DOFs. The installation site for the conversions is divided into three sections. First, the WECs erected near the coastline or linked to man-made structures, such as breakwaters, are referred to as onshore systems. Second, the nearshore systems are positioned 500 to 2000 m from the coast at a depth of 10 to 25 m. Around a quarter of wavelengths are presented in the nearshore areas. Eventually, the WEC technologies vary from 40 to 100 m respective to the depth of the WEC installations, making adaptive conversions problematic due to the incoming waves [85]. The various WEC type categories are briefly described below.

Point Absorbers
As a kind of WEC device, the point absorbers (PAs) have features and shapes thinner than the incident wavelength. The point absorbers may function in heave, pitch, or multiple DOFs, can be installed onshore or offshore, and can act as one-and two-bodies based on the number of bodies involved. While the latter (two-body) are absolute displacement references about the seabed or offshore structures, the majority of the former (one-body) are self-referenced. The standard shapes of one-and two-body PAs are shown in Figure 2. The PAs with one-body interact with the ocean waves using a single body that is either floating or submerged, and the body's motion drives a stationary PTO device to generate the energy. The body's natural frequency and response amplitude operator (RAO), an essential part of the dynamics, shows a low-pass behavior in the frequency domain and significantly impacts the body's geometrical structure. The two-body point absorbers use two bodies' relative motion and may operate offshore without requiring mooring devices since they do not need a fixed point of reference. The band-pass properties are unique to the two-body PAs, which allow the band-pass to be tuned to specific wave spectra [86]. The two-body PAs have more complicated geometric forms and need more parameters to specify their geometries than the one-body PAs. Unlike the one-body PAs, which work as low-pass filters, the two-body PAs function as band-pass filters, with the appropriate bandwidths being very sensitive to the geometric forms.

Oscillating Water Columns
An open structure with an open inlet is used in an oscillating water device to trap air above the inner free surface and above the still water level. The trapped air is compressed and released by the wave action in alternating cycles by opening a valve that directs the airflow into a turbine connected to a power plant [87]. The oscillating wave columns (OWCs) do not need an end-stop function since there is no oscillating linear motion present in them. The two types of OWCs are floating and fixed, whereby the fixed OWCs are connected to the breakwaters or the shore [88]. Figure 3 illustrates examples of these  The PAs with one-body interact with the ocean waves using a single body that is either floating or submerged, and the body's motion drives a stationary PTO device to generate the energy. The body's natural frequency and response amplitude operator (RAO), an essential part of the dynamics, shows a low-pass behavior in the frequency domain and significantly impacts the body's geometrical structure. The two-body point absorbers use two bodies' relative motion and may operate offshore without requiring mooring devices since they do not need a fixed point of reference. The band-pass properties are unique to the two-body PAs, which allow the band-pass to be tuned to specific wave spectra [86]. The two-body PAs have more complicated geometric forms and need more parameters to specify their geometries than the one-body PAs. Unlike the one-body PAs, which work as low-pass filters, the two-body PAs function as band-pass filters, with the appropriate bandwidths being very sensitive to the geometric forms.

Oscillating Water Columns
An open structure with an open inlet is used in an oscillating water device to trap air above the inner free surface and above the still water level. The trapped air is compressed and released by the wave action in alternating cycles by opening a valve that directs the airflow into a turbine connected to a power plant [87]. The oscillating wave columns (OWCs) do not need an end-stop function since there is no oscillating linear motion present in them. The two types of OWCs are floating and fixed, whereby the fixed OWCs are connected to the breakwaters or the shore [88]. Figure 3 illustrates examples of these OWCs. One significant benefit of fixed OWCs is that other functional needs, such as breakwaters [89], may split the costs for the infrastructure, resulting in a reduced levelized cost of energy (LCoE). In addition, the testing conducted in open water on the permanently installed OWCs proves their reliability and resilience in extreme weather and waves [24].

Attenuators
Parallel to the direction of the waves, the attenuators are free-floating WEC devices made up of a series of bodies linked by hinges, such that the motion of one body relative to another may power a PTO. As seen in Figure 4, the Pelamis [90] is a prominent example of an attenuator-type WEC.

Attenuators
Parallel to the direction of the waves, the attenuators are free-floating WEC devices made up of a series of bodies linked by hinges, such that the motion of one body relative to another may power a PTO. As seen in Figure 4, the Pelamis [90] is a prominent example of an attenuator-type WEC.

Attenuators
Parallel to the direction of the waves, the attenuators are free-floating WEC devices made up of a series of bodies linked by hinges, such that the motion of one body relative to another may power a PTO. As seen in Figure 4, the Pelamis [90] is a prominent example of an attenuator-type WEC.

Terminators
The overtopping technologies, the oscillating wave surge converters (OWSCs), and the "duck-like" systems are all examples of terminators that are positioned perpendicular to the wave direction. Flaps, flaps with vanes, cylinder C-cell shapes, and flaps with arbitrary designs are all used in OWSCs to facilitate the interaction between the wave and the structure. The most important factors to consider while designing these forms are the flap size and depth to which they are submerged. There is some overlap between the categories of the PA and OWSC. However, in this context, the cylindrical devices are considered OWSCs since their working principle and optimization strategy are similar to those of other OWSCs. The overtopping devices, such as the WD and the sea slot-cone generator (SSG), as depicted in Figure 5, rely on the angle, freeboard and draught, and the ramp shape to function at their best [91][92][93].

Terminators
The overtopping technologies, the oscillating wave surge converters (OWSCs), and the "duck-like" systems are all examples of terminators that are positioned perpendicular to the wave direction. Flaps, flaps with vanes, cylinder C-cell shapes, and flaps with arbitrary designs are all used in OWSCs to facilitate the interaction between the wave and the structure. The most important factors to consider while designing these forms are the flap size and depth to which they are submerged. There is some overlap between the categories of the PA and OWSC. However, in this context, the cylindrical devices are considered OWSCs since their working principle and optimization strategy are similar to those of other OWSCs. The overtopping devices, such as the WD and the sea slot-cone generator (SSG), as depicted in Figure 5, rely on the angle, freeboard and draught, and the ramp shape to function at their best [91][92][93].

Power Take-Off Mechanism
The mechanism that transforms the electrical energy generated by the primary conversion is known as the PTO. The direct conversion may be seen in a PA buoy or a water column resonator chamber. The efficiency with which the absorbed wave power is transformed into electricity is directly related to the PTO system's influence on the wave energy converter's mass, dimensions, and structural dynamics.
The PTO system has a direct effect on the LCoE [94] since it affects the efficiency with which the wave energy is converted. The PTO system directly influences the effectiveness of the power conversion and, hence, the annual energy generation. The capital cost of a device is directly affected by the PTO system, which accounts for around 20%-30% of the total cost [95]. How well the PTO system functions determines on how much it costs to run and maintain, as well as how much energy it produces. Figure 6 displays a schematic of the PTO's impact on the LCoE [96]. The PTO variables were studied by the Danish

Power Take-Off Mechanism
The mechanism that transforms the electrical energy generated by the primary conversion is known as the PTO. The direct conversion may be seen in a PA buoy or a water column resonator chamber. The efficiency with which the absorbed wave power is transformed into electricity is directly related to the PTO system's influence on the wave energy converter's mass, dimensions, and structural dynamics. The PTO system has a direct effect on the LCoE [94] since it affects the efficiency with which the wave energy is converted. The PTO system directly influences the effectiveness of the power conversion and, hence, the annual energy generation. The capital cost of a device is directly affected by the PTO system, which accounts for around 20-30% of the total cost [95]. How well the PTO system functions determines on how much it costs to run and maintain, as well as how much energy it produces. Figure 6 displays a schematic of the PTO's impact on the LCoE [96]. The PTO variables were studied by the Danish organization Partnership for Wave Energy to determine the impacts of improvements in the PTO efficiency and the PTO framework cost reduction on the LCoE. formed into electricity is directly related to the PTO system's influence on the wave energy converter's mass, dimensions, and structural dynamics.
The PTO system has a direct effect on the LCoE [94] since it affects the efficiency with which the wave energy is converted. The PTO system directly influences the effectiveness of the power conversion and, hence, the annual energy generation. The capital cost of a device is directly affected by the PTO system, which accounts for around 20%-30% of the total cost [95]. How well the PTO system functions determines on how much it costs to run and maintain, as well as how much energy it produces. Figure 6 displays a schematic of the PTO's impact on the LCoE [96]. The PTO variables were studied by the Danish organization Partnership for Wave Energy to determine the impacts of improvements in the PTO efficiency and the PTO framework cost reduction on the LCoE. A decrease in the LCoE is associated with both an efficiency improvement and the PTO cost reduction. Although a boost in the PTO performance has a more noticeable impact on the LCoE, both variables significantly impact the LCoE, indicating the importance of the PTO system in a wave energy conversion.
Wave Energy Levelized Cost of Energy (LCoE) A decrease in the LCoE is associated with both an efficiency improvement and the PTO cost reduction. Although a boost in the PTO performance has a more noticeable impact on the LCoE, both variables significantly impact the LCoE, indicating the importance of the PTO system in a wave energy conversion.
However, creating a cost-effective PTO framework is not a simple undertaking. The energy resource's inherent characteristics provide the most significant obstacle, specifically referring to the high variability observed in ocean energy. The surface elevation of the waves fluctuates erratically over time and may quickly cause a body to experience large amplitude displacements, accelerations, and forces. Other times, waves exhibit smallamplitude forces, accelerations, and displacements. Different dynamic load patterns may be seen in these two extreme regimes, large and small-amplitudes, and the PTO system should operate as effectively as feasible. Because of their location and/or unfavorable weather conditions, the WECs are put in a highly hostile environment with a high wear rate. The PTO system should be as durable, dependable, and low maintenance as the rest of the equipment. Figure 7. depicts different ways of producing electricity from ocean waves.
terns may be seen in these two extreme regimes, large and small-amplitudes, and th system should operate as effectively as feasible. Because of their location and/or un able weather conditions, the WECs are put in a highly hostile environment with wear rate. The PTO system should be as durable, dependable, and low maintena the rest of the equipment. Figure 7. depicts different ways of producing electricit ocean waves. A variety of PTO setups have been proposed in other studies, highlighting th versity. Many different types of wave energy conversion use different PTOs. Sinc is a lack of data and only two kinds of systems may be tied to one specific devi challenging to systematically compare the many PTO types. The five primary sub ries of PTO systems include air turbines, hydraulic converters, hydro turbines, dir chanical drive systems, and direct electrical drive systems.
The WEC lacks an industrial standard device, unlike the wind energy indust this variation is carried to the PTO system. Numerous PTO system types have bee ied, including vigorously the kind of WEC. An air turbine is used in the oscillating column device, which is connected to an electrical generator. In contrast, the PA f conversion may need cascaded conversion mechanisms and may utilize various PT tems depending on their arrangement. Due to this variation, PTO systems are stil research phase and have minimal practical experience with large-scale devices. Sin challenging to evaluate PTO systems at a small scale because of friction, it is pos try them out at a grander scale with higher expenses.

Hydrodynamic Interaction Definition
Choosing a technique for assessing a WEC and resolving the hydrodynamic i tions is difficult when surveying wave energy conversion projects. Additionally, it ful to comprehend the acting interactions and the applied forces. The most curr search on numerical approaches to model a WEC is covered in this section, follow the difficulties with the interaction and its parameter.
Most wave energy conversion array projects need the simulation of an isolated The WEC may be simulated using various methods, each with a unique sim A variety of PTO setups have been proposed in other studies, highlighting their diversity. Many different types of wave energy conversion use different PTOs. Since there is a lack of data and only two kinds of systems may be tied to one specific device, it is challenging to systematically compare the many PTO types. The five primary subcategories of PTO systems include air turbines, hydraulic converters, hydro turbines, direct mechanical drive systems, and direct electrical drive systems.
The WEC lacks an industrial standard device, unlike the wind energy industry, and this variation is carried to the PTO system. Numerous PTO system types have been studied, including vigorously the kind of WEC. An air turbine is used in the oscillating water column device, which is connected to an electrical generator. In contrast, the PA form of conversion may need cascaded conversion mechanisms and may utilize various PTO systems depending on their arrangement. Due to this variation, PTO systems are still in the research phase and have minimal practical experience with large-scale devices. Since it is challenging to evaluate PTO systems at a small scale because of friction, it is possible to try them out at a grander scale with higher expenses.

Hydrodynamic Interaction Definition
Choosing a technique for assessing a WEC and resolving the hydrodynamic interactions is difficult when surveying wave energy conversion projects. Additionally, it is helpful to comprehend the acting interactions and the applied forces. The most current research on numerical approaches to model a WEC is covered in this section, followed by the difficulties with the interaction and its parameter.
Most wave energy conversion array projects need the simulation of an isolated WEC. The WEC may be simulated using various methods, each with a unique simulation duration and quality. Some modeling methodologies, based on the potential flow (PF) are presented in order of a decreasing simulation duration, which can be divided into four distinct types: frequency-domain linearized PF, time-domain linearized PF, semi-analytical approaches, and nonlinear PF.
Most research uses the first method, the frequency-domain linearized PF, with WAMIT, NEMOH, and ANSYS AQWA as the most often used solvers. Researchers continue to utilize the linearized approach primarily for the relatively small arrays, despite its shortcomings since it quickly produces valuable findings. Several studies utilized the semi-analytical method. The direct matrix technique [98], the multiple body radiation and diffraction [99], multiple scattering (either iterative or non-iterative) [100], and the WEC-MS [101] are some of the most often used solvers in modern programs. The PF is linearized in both the frequency and time domains; although the latter may include transient effects and nonlinear external influences, the former cannot contain the transient impact. All nonlinear forces, such as the viscous drag, the flow separation, and the vortex shedding, are accounted for in this model through a nonlinear potential flow.
Computational fluid dynamics (CFD), a subfield of fluid dynamics that deals with the numerical study of fluid flows, is capable of addressing the formidable challenges. The direct numerical simulation (DNS), the large eddy simulation (LES), Reynolds average Navier-Stokes (RANS), and the hybrid RANS/LES are the most accurate techniques for solving the Navier-Stokes equations (NSEs).
Several aspects must be considered to determine the best approach reported in the literature. First, the flow must be classified as turbulent or laminar. Second, a flow might be regarded as incompressible, irrotational, or inviscid to simplify the process of solving equations. For instance, linearized a PF considers all three types.
In terms of BEM solvers, WAMIT is one of the several programs available for understanding how offshore structures and waves interact. One benefit of this program is using the high-order boundary element method (HOBEM) to accelerate computing [38]. The NEMOH solver package, on the basis of the BEM, has merit for the diffraction issue since the package is simple to use and can readily handle a user-defined distribution of normal velocities at the center of each mesh panel. ANSYS AQWA applies the three dimensions radiation/diffraction theory to simulate the global loading and motion. The PF-based models have been widely used in offshore investigations, and these techniques may provide unrealistic simulations in the event of wave resonance because they neglect the viscosity effects. Additionally, the viscous and turbulent effects can only be considered using the CFD-based approaches, which also suffer from high costs for the sector.
Calculating the applied forces on each WEC is the consequence of selecting a method to simulate and solve the hydrodynamic coefficients. All forces operating on a WEC device may be computed, for example, when the hydrodynamic coefficients, such as the additional mass and the damping coefficients are solved in the PF solvers. Per Newton's second law, several forces are involved in resolving the equation of motion, which states that a body's mass times its rate of acceleration, equals the active forces [102].
The interaction between the buoys must be taken into account when placing more than one in the chosen marine area. In certain circumstances, the decrease or increase in the total of each individual conversion power relative to the array power may be directly attributed to the interaction between devices. Budal [31] initially used the "hydrodynamic interaction" term in 1976 to describe the ratio of the total power production by the WEC array and a single WEC.
where N represents the number of conversions; P i is the single WEC power; and P a is the power of the WEC array. Numerous studies on relative equations and interaction optimization have been conducted recently. Not all articles discussing the estimate of interaction applied a conventional equation, such as Borgarino [51], who used the q mod , which excludes the physical size and shape notions as follows: where P o and P i are the power produced by the individual WEC and the i-th WEC in the array, respectively.
Other studies then attempted to propose a novel method or analytical strategy to assess the efficacy of interactions. For instance, an extracted connection, based on the previous q-factor is provided by Sun [103]. To study the possible interaction effects, the researchers took into account various distances and wave periods, as follows: where the maximum of P c,isolated is the highest absorbed power by an individual WEC. The exact definition of the q-factor, as in Equation (5), applies here; if q is greater than 1, then the constructive interaction occurs. Using this approach, the layout's efficiency may be calculated by looking at the hydrodynamic properties.
Researchers also examined the optimum configuration for increasing the q-factor in order to take advantage of the positive interaction and its relative advantages. The array will operate more effectively and absorb more energy by interacting positively. Consequently, several investigators aimed to obtain the greatest q-factor while discussing the WEC findings in an array.

Recent Advances in Optimizing the WEC Configuration
This section summarizes the optimization strategies by examining the evolution of the WECs' array arrangement, structural shape and size, and the PTO systems.
To find the best multiple optimal solutions from all possible solutions, the metaheuristic optimization techniques are often used to tackle multi-objective optimization issues. These strategies evaluate the potential options, go through a series of steps to generate several offspring, and then attempt to converge on the most promising answers. Many practical engineering optimization problems have been solved by different metaheuristic methods developed during the last few decades [104]. Based on earlier studies, we have categorized the meta-heuristics into three groups: genetic algorithms, multi-objective algorithms, and many-objective algorithms. Many algorithms incorporate principles from multiple classes, which are termed hybrid techniques [104]. In addition, one study performed comparative studies to evaluate the efficacy of the optimization techniques, which may be useful in pointing the end-users toward an optimization strategy most suited to their specific circumstances [105].
Several optimization strategies have been suggested to enhance the WECs' energy extraction potential, as shown by the abundance of the optimization techniques and their implementations in the linked studies. The optimal optimization strategies depend heavily on the nature of the issue, the relative importance of the primary decision criteria, and the objective function design. In addition, we will cover the arrangement of the array, the structural shape and size, and the PTO systems optimization in each classification.

Optimization Approaches
Converging to the best solution directly in most actual engineering issues is difficult. Yet, putting up a loss function that gauge's the solution quality and decreases its parameters to discover the best possible solution is not easy. Some of the research initiatives explore numerical approaches. This section thoroughly discusses several optimization methods applied in the WEC systematic design.
Noad and Porter [106] used a multi-dimensional numerical optimization to assess the solution method's correctness and to determine the appropriate device settings for the array optimization. The design of the WEC arrays was described by Ruiz et al. [55], using four parameters, as well as looking at the GA, the glowworm swarm optimization (GSO), and the CMA-ES. In contrast to the GA and GSO, the CMA requires less processing power, as found by the researchers. Raju [107] employed the Nelder-Mead (NM) search method to determine the best PTO parameters for each WEC and the derivative-free continuous optimization, the CMA-ES, to enhance the conversion location by minimizing the negative interactions.
Thomas et al. [108] presented a shallow artificial neural network (ANN) to find the ideal latching times in irregular wave situations. According to the results, for particular sea conditions, the learnable WEC absorbs twice as much power as the WEC without latching and 30% more power when compared to the test wave's best consistent latching time. Complex PTO control methods, such as the latching-declutching optimization, aim to improve the overall system performance. Due to the discontinuous nature of the loss function in this optimization issue, Feng and Kerrigan [109] opted to adopt a novel derivative-free coordinate-search approach, developing a formulation based on historical wave data and forecasting future wave behavior. To demonstrate the algorithm's effectiveness, it was compared to the simulated annealing (SA) algorithm, a global metaheuristic technique without derivatives.
The bio-inspired algorithms use simple, naturally derived techniques to address complicated issues. Since many biological processes may be considered a local optimization, these techniques imitate nature. They fall under the scope of randomized algorithms and extensively use arbitrary choices. This method has gained much popularity because it can be used to tackle complicated issues in all major branches of computer science and offers solutions to a wide variety of issues. Bio-inspired algorithms have been divided into many categories, including ecology-based, multi-objective, many-objective, and EAs. Here, we discuss three types: genetic, multi-objective, and many-objective algorithms.

Genetic Algorithm
In the search space, the genetic algorithms look for appropriate solutions. These algorithms typically follow three steps. First, they perform some preliminary work on the samples. Once they have transformed the original samples into new ones, the goal function is established by selecting the old and new ones, and the computation is terminated, based on the termination criteria. The preliminary concepts of optimization are presented to provide an overview of employing EAs in a WEC [35], which these notions discover the best array configurations using the parabolic intersection (PI) and GA approaches. The PI was found to be substantially more computationally effective even though the GA performed better in terms of performance. Moarefdoost et al. [34] conducted similar research and suggested a heuristic optimization approach to locate a layout with the highest possible q-factor. This algorithm outperformed the modified GA in terms of performance-the argumentative articles on the GA below present the related research endeavors.
The individual WEC dimensions and the array configuration of the cylindrical buoys in the WECs were optimized using the GA by Lyu et al. [110]. Abdelkhalik and Darani [111] proposed a hidden genes GA (HGGA) for the nonlinear management of the WECs and to maximize the system non-linearities brought about by the shape, significant buoy movements, and the PTO. The results show that the shaped-based technique employed in this research may encompass all of the wave data for the process optimization and has a satisfactory convergence rate. Goteman et al. [44] presented a tool for optimizing the key parameters using the GA, including the draft value and radius of a single point-absorbing WEC. This technique improved the arrays of 4 to 14 comparable point-absorber WECs. Giassi et al. [112] developed and implemented a methodology for the non-homogeneous arrays of WECs, in which the interaction factor was an extra objective function that Sharp and DuPont [113] offered in their GA technique. Their study focused on the impacts of spacing while reducing the harmful interactions to increase power.
Liu et al. [114] used nine random design parameters as the starting point for their OWSC investigation, and DualSPHysics to simulate them. Following the training of a radial basis function neural network (RBFNN), the capture factors were acquired, and these parameters were then adjusted using the GA. Even if there is a lot of interest in using the GA, many researchers have been studying and applying various optimization techniques over the last ten years. For instance, Wu et al. [54] reported optimizing a three-tether submerged buoy array by combining two EAs, including (1+1)-EA and CMA-ES, which proved successful. A solution was converged using (1+1)-EA and then fine-tuned using the CMA-ES. In spite of employing a wave model, it was neither realistic nor very advanced. In one of the earliest studies, Powell [115] developed a constrained optimization technique using the linear approximation (COBYLA) as a numerical optimization method for the constrained problems where the derivative of the objective function is unknown.

Evolutionary Multi-and Many-Objective Algorithms
As a general rule, when there are more than two objectives at play, there is not just one best solution but rather a collection of them (often referred to as Pareto-optimal solutions). One of these Pareto-optimal solutions cannot be chosen over the other without further data; therefore, finding as many Pareto-optimal solutions as possible is necessary. The traditional optimization techniques (such as the multi-criterion decision-making techniques) advocate focusing on a single Pareto-optimal solution inside a multi-objective optimization problem. To obtain a variety of answers, this technique must be carried out repeatedly, with the expectation that each simulation run would provide an exceptional result.
There have been several proposals for many-objective optimization algorithms (MOEAs) [116][117][118][119] throughout the last decade to facilitate the optimization of multiple objectives simultaneously. This is driven by the motivation to uncover several Pareto-optimal solutions in a single simulation run as a capability of these methods. Since EAs operate on a population of solutions, a basic EA may be modified to preserve a wide variety of options. An EA may uncover numerous Pareto-optimal solutions in a single simulation run, focusing on progressing toward the genuine Pareto-optimal area. One of the first examples of such EAs is the nondominated sorting genetic algorithm (NSGA) described in [117].
The adaptability and robust global searchability of the swarm intelligence (SI) algorithms make them a powerful tool in many contexts. Specifically, the particle swarm optimization (PSO) is one of these well-known methods, which uses a particle's motion in a population to obtain the best local and global solutions. A prior study optimized the key WEC parameters using a GA, PSO, and hybrid GA/PSO (HGA-PSO) technique [120]. Faraggiana et al. [121] contrasted the capabilities of the GA and PSO in their study on the minimal LCoE development of WaveSub WECs. Both algorithms performed almost identically, as seen by the results.
The particle swarm optimization (PSO) and other bio-inspired optimization methods have been used in a remarkable number of real-world applications that have been documented in the literature. In order to generate a wide variety of WEC designs and account for other elements that might affect costs, Garcia-Teruel et al. (2020) [122] studied the hull geometry optimization of WECs, based on flexible geometry specifications, such as basic shapes or B-spline surfaces. Using the PSO and GA, they looked for effective optimization strategies for the WEC geometry design.
A novel method for incorporating wave energy into the grid via an effective control system for maximum power was presented by Talaat et al. (2021) [123]. The whale optimization algorithm (WOA), the artificial immune system (AIS), the bat algorithm (BA), and the PSO were the four meta-heuristic optimization approaches used in this study. These techniques are implemented so that the best possible parameter design may be obtained depending on the electrical power of the wave's output. To investigate the true generating potential of this WEC system, Mahdy et al. (2022) [124] developed a nonlinear model of a grid-connected Archimedes wave swing (AWS). Six proportional-integral (PI) controllers maximize the wave energy harvesting, minimize the power losses in the generator, and preserve the grid and the DC connection voltages steady at the setpoints. In addition to using the PSO and COOT as references for comparison, they use a hybrid augmented grey wolf optimizer and cuckoo search (AGWO-CS) method to choose the PI controller.
Moreover, Neshat et al. (2021) [125] optimized a multi-mode WEC design using an enhanced moth flame optimization (MFO) technique. They examined and evaluated the efficacy of the bio-inspired swarm-evolutionary optimization methods for adjusting the WEC's shape, tether angles, and PTO settings. Compared to other algorithms, such as the PSO, GWO, WOA, and CMA-ES, they determined that the enhanced MFO algorithms performed the best. Neshat et al. (2022) [126] conducted an additional study on the WEC layout optimization using a unique multi-swarm cooperative method with a backtracking technique. The suggested method by these researchers is oriented toward resolving the challenges associated with optimizing the placement of WECs in a wave farm. This new method uses a trio of meta-heuristics algorithms: the multiverse optimizer (MVO) methodology, the equilibrium optimization (EO) method, and the MFO approach with a backtracking strategy.
On top of that, Huang et al. (2021) [127] looked at the PA-type WEC to see if they could obtain the most power out of it. In order to identify the optimal values for the wave characteristics and the WEC system-related parameters RPTO and XPTO, a novel global power point tracking (MPPT) control technique, built on the PSO algorithms is used. They also compared their findings using the flower pollination algorithm (FPA).

Layout-PTO-Geometry Optimization
Numerous studies investigated the prospect of enhancing the array's capacity to absorb energy by considering various designs. Such arrangements may result in a 30% reduction in the array or even a growth of around 5%. Over the last decade, many researchers have examined the uncomplicated regular, and unpredictable patterns and found that the optimized patterns may be a solid option to impact extracting power positively.
A number of variables influence the placement of buoys in an array, which could be beneficial or destructive depending on the project's ultimate objective. In particular, the closer WECs are to one another, the greater the adverse effects when less expensive cabling is used. The six most important elements in designing an array are discussed as follows. First, the number of WECs profoundly affects the overall design, whereby more than four transformations are needed for the polygonal and circular designs. Second, the array's behavior may shift if each conversion is handled separately. Therefore, the power absorbed by an array would be the same as the power of the isolated powers, and the interaction effects of the array may even be negligible. Third, the power absorption characteristic is very sensitive to sea conditions. As a result, the wave interaction effects are applicable, and a lot of energy is consumed when the natural period of the system is similar to the wave period. In the case of regular waves, the wave's direction and frequency also directly affect the excitation force. The interaction factor is susceptible to the strength of the excitation force used on the device. Fourth, the direction of the waves may have a significant role in determining the design. This may be tested in two ways: theoretically by rotating the array pattern or experimentally by employing different definitions at different points in the study. Despite the fact that most publications solely take into account unidirectional waves, the correlation of multidirectional waves also needs consideration. Fifth, the amount of energy harvested from each WEC is affected by its individual size. Finally, it is essential to consider how waves interact with the buoys when placing them to minimize the detrimental effects. Table 1 presents the examples of the most recent literature that meet the requirements for selecting the optimal design of a WEC array, as part of their configurations, numbers of WECs, and types of conversion.  Average power - [138] In order to avoid the shadowing and masking effects, the WEC does not have to be arranged parallel to the wave direction. Two of these configurations are perpendicular to the wave's movement, namely the linear and arrow patterns. Figure 8 illustrates the layout of the array configuration for the different WEC types and the device numbers, based on recent studies. Table 1 presents the examples of the most recent literature that meet the requirements for selecting the optimal design of a WEC array, as part of their configurations, numbers of WECs, and types of conversion. Average power - [138] In order to avoid the shadowing and masking effects, the WEC does not have to be arranged parallel to the wave direction. Two of these configurations are perpendicular to the wave's movement, namely the linear and arrow patterns. Figure 8 illustrates the layout of the array configuration for the different WEC types and the device numbers, based on recent studies. In summary, increasing the number of WECs and the interval between the conversions enhance the absorbed power. However, eventually, the average amount of harnessed energy decreases. Furthermore, greater power is produced with a shorter wave period. A WEC's dimensions must also catch more energy while using less. We also found that every research used a distinct main setup. Even though Goteman's review study [40] implies that layout patterns are inclined to be precisely perpendicular to the path of the prevailing wave, it is still important to take note of the arrow and staggered layouts in the  [42], and (c) Lyu et al. [110].
In summary, increasing the number of WECs and the interval between the conversions enhance the absorbed power. However, eventually, the average amount of harnessed energy decreases. Furthermore, greater power is produced with a shorter wave period. A WEC's dimensions must also catch more energy while using less. We also found that every research used a distinct main setup. Even though Goteman's review study [40] implies that layout patterns are inclined to be precisely perpendicular to the path of the prevailing wave, it is still important to take note of the arrow and staggered layouts in the regular patterns that do not employ optimization techniques to yield valuable outputs [40].
The LCoE for the WECs may be reduced by using various design and control approaches, which would result in a lower capital cost of energy. When planning a WEC's optimal PTO system, there are two significant challenges to surmount. The first issue is that the irregular wave changes introduce more uncertainty into the subsequent deterministic analysis. Second, the converter may experience unexpected forces that increase or decrease its displacement, velocity, or acceleration, due to the unforeseen changes in the WEC's position aquaculture. Research on optimizing the PTO settings or control strategy coefficients has recently been conducted [139]. In Figure 9, a hydraulic PTO (HPTO) of a two-body point absorber is illustrated, which recently was the main focus of several types of research. Different algorithms have been presented to optimize the HPTO settings, some of which are demonstrated in Figure 10.
x FOR PEER REVIEW 19 of 30 regular patterns that do not employ optimization techniques to yield valuable outputs [40].
The LCoE for the WECs may be reduced by using various design and control approaches, which would result in a lower capital cost of energy. When planning a WEC's optimal PTO system, there are two significant challenges to surmount. The first issue is that the irregular wave changes introduce more uncertainty into the subsequent deterministic analysis. Second, the converter may experience unexpected forces that increase or decrease its displacement, velocity, or acceleration, due to the unforeseen changes in the WEC's position aquaculture. Research on optimizing the PTO settings or control strategy coefficients has recently been conducted [139]. In Figure 9, a hydraulic PTO (HPTO) of a two-body point absorber is illustrated, which recently was the main focus of several types of research. Different algorithms have been presented to optimize the HPTO settings, some of which are demonstrated in Figure 10.   [40].
The LCoE for the WECs may be reduced by using various design and control approaches, which would result in a lower capital cost of energy. When planning a WEC's optimal PTO system, there are two significant challenges to surmount. The first issue is that the irregular wave changes introduce more uncertainty into the subsequent deterministic analysis. Second, the converter may experience unexpected forces that increase or decrease its displacement, velocity, or acceleration, due to the unforeseen changes in the WEC's position aquaculture. Research on optimizing the PTO settings or control strategy coefficients has recently been conducted [139]. In Figure 9, a hydraulic PTO (HPTO) of a two-body point absorber is illustrated, which recently was the main focus of several types of research. Different algorithms have been presented to optimize the HPTO settings, some of which are demonstrated in Figure 10. Currently, there are 21, 13, 13, and 11 active firms for the hydro-turbine, hydraulic systems, air turbines, and direct electrical systems, respectively, and 31 other companies actively developing direct mechanical techniques. About nine more companies are working on different PTO systems that are not included in this research. The PTO systems in the wave energy setups are often built-in linear spring-damper systems, with the power output proportional to the Coulomb damping [54], and are independent of the deployed mechanical equipment. Additionally, the linear generators may easily increase the simplicity of the direct drive PTO systems. For example, the flux-switching permanent magnet linear generators (FSPMLGs) [142] may be used to directly transform the waves' oscillatory motion into a generator's constant rotation in one direction.
We examined several works on the point absorber geometry optimization. For example, the floating single-body point absorber, SEAREV, underwent a multi-objective geometry optimization by Babarit et al. [143]. According to the results, the biggest draught designs produced the most ideal performances. The results of the reviewed works on tuning the PTO parameters using different algorithms are depicted in Figure 11.
Additionally, all of the above researchers discovered that altering the float's mass had no appreciable impact on the power output of the WEC. Table 2 summarizes several recent investigations on the optimization of the WEC hull design. Currently, there are 21, 13, 13, and 11 active firms for the hydro-turbine, hydraulic systems, air turbines, and direct electrical systems, respectively, and 31 other companies actively developing direct mechanical techniques. About nine more companies are working on different PTO systems that are not included in this research. The PTO systems in the wave energy setups are often built-in linear spring-damper systems, with the power output proportional to the Coulomb damping [54], and are independent of the deployed mechanical equipment. Additionally, the linear generators may easily increase the simplicity of the direct drive PTO systems. For example, the flux-switching permanent magnet linear generators (FSPMLGs) [142] may be used to directly transform the waves' oscillatory motion into a generator's constant rotation in one direction.
We examined several works on the point absorber geometry optimization. For example, the floating single-body point absorber, SEAREV, underwent a multi-objective geometry optimization by Babarit et al. [143]. According to the results, the biggest draught designs produced the most ideal performances. The results of the reviewed works on tuning the PTO parameters using different algorithms are depicted in Figure 11.   Additionally, all of the above researchers discovered that altering the float's mass had no appreciable impact on the power output of the WEC. Table 2 summarizes several recent investigations on the optimization of the WEC hull design.

Future Research Direction
In this article, we take an in-depth look at the latest research on the optimization algorithms and their usage in the context of WECs. The advancement of WECs is proving to be challenging at all times. Finding ideal setups for these devices offers a wealth of opportunities for exploration, extension, and the smoothing of information due to the high uncertainty associated with the variables linked to wave energy at temporal and geographical scales. Because of this, the typical optimization algorithms' limitations impose a ceiling on the degree of uncertainty associated with finding optimum designs. There is a plethora of optimization methods available for addressing the processing mode.
Conversely, several studies have used the GA as their principal strategy alongside local and global search algorithms, owing to its superior performance in finding optimum solutions. Therefore, increasing these algorithms' efficiency is another difficulty. Due to the lack of inquiry, it is necessary to include many objectives to gain a more realistic optimum configuration, which calls for further research. While more than three or five objectives may be included in a single optimization method, there is a lack of definitive research on designing multi-objective and many-objective optimization algorithms. The WEC size and shape, hotspot and array design, PTO configuration, and reducing costs by optimizing the LCoE are all examples of objectives that might be pursued. According to the analyzed literature, the precision and calculation time are influenced by the quality of the objectives. The model's efficiency is bolstered by the depth and consistency of its objectives and algorithms. When trying to optimize the structure of the WEC or investigate the nonlinear correlations, the importance of the variable correlations cannot be overstated.
A solution to the uncertainty about future research directions and methods lies in the investigation, refinement, and expansion of the multi-and many-objective optimization algorithms. Future studies should focus on more viable methods for the aforementioned problems in its use and the development of more practical structures. In order to examine the uncertainty and volatility adequately, it may be necessary to develop novel evolutionary algorithms or combine current approaches. Additionally, the GA has been the dominant technique in most applications, but it is insufficient for achieving the best design of WECs to their full extent. Due to the intricacy of wave energy research, determining the optimal design for each purpose should be prioritized.

Conclusions
Researchers are quickly working on developing technologies to harness the energy of ocean waves, due to their enormous potential as a renewable energy source. Compared to other renewable resources, the WEC technologies need further improvement before being commercialized. The layout and PTO optimization are key factors in generating the most power possible using WECs. However, their optimization is difficult because of the intricate hydrodynamic interaction across the conversions.
In this paper, we first discussed the various categorizations of conversions. While there are additional aspects to consider, we found that the categorization based on the operating principles, in combination with the hydro-mechanical conversion technology is more comprehensive. The unraveling of the hydrodynamic interactions is explained in detail using numerical techniques and solvers. Then, we described the most current studies that used at least one of the mentioned approaches. To begin the investigation, it was essential to appropriately estimate what causes the interaction between WECs and the applied forces for the chosen conversion type. Depending on the size of the project and the level of precision needed, a low-fidelity or high-fidelity method should be chosen.
Due to the growing number of algorithms and the objective functions being investigated in this area, a study of the optimization issues was then conducted. The conclusion is that most research has focused on employing the GAs with a single objective function, while studies on the multi-and many-object optimization of the WEC layout, geometry, and PTO settings are lacking. Numerous studies on the GA, EA, and differential equation (DE) methods, combined with adaptive neuro-surrogate optimization (ANSO), hybrid coordination channel access (HCCA), and generic local search techniques improved the accuracy and the different parameter tuning of these methods. To this end, the following is a summary of the results of the PTO system, geometry optimization, and layout optimization: -Numerous relevant elements are used in the layout optimization studies to find the best solutions. In order to identify the most consistent, repeatable findings throughout the examined research, two patterns, namely the linear and the arrowhead patterns, are depicted in this study. The performance of the arrangement is directly affected by variables, such as the distance and wave direction. Therefore, we agree on a general statement of how increasing or decreasing these factors affects the arrangement of the array. - Recently, it has been established as a reasonable standpoint to use the optimization techniques to increase the control methods and enhance the PTO coefficients. The modern meta-heuristic algorithms have also optimized these coefficients. Recent research shows that the maximum power output at lower frequencies increases with the increasing damping coefficient. Experimental evidence is presented to support this notion. A complete cost-benefit analysis is required for each of the many PTO systems that are categorized in this paper, even if the PTO system setup will enhance the LCoE. Further study on the active control methods for the PTO system of the conversions is needed. -According to studies, the WECs' shape optimization may significantly boost performance. Geometry optimization combined with the PTO control approach may lead to better outcomes. While increasing the WECs' geometry will boost their profitability, performance should be adjusted in light of the rising prices.
In conclusion, we argue that future research focusing on multi-and many-objective studies, with an emphasis on cost and maximum absorbed energy, is more likely to provide valuable discoveries and information. Furthermore, it is clear from the publications that very few studies use the CFD instead of BEM as the numerical technique. Given the GA's popularity, we advocate employing other trustworthy meta-heuristic algorithms that can provide superior results in a shorter amount of time.
Funding: This research received no external funding.

Institutional Review Board Statement: Not applicable.
Informed Consent Statement: Not applicable.

Data Availability Statement:
The study did not report any data.

Conflicts of Interest:
The authors declare no conflict of interest.