Numerical Study on Aerodynamic Characteristics of Heavy-Duty Vehicles Platooning for Energy Savings and CO 2 Reduction

: This study aims to analyze the aerodynamic interaction between moving vehicles platoon-ing with the change in the platooning conditions on a freeway. The effect of the vortex generated by the forward vehicle reduces the value of the stagnation pressure generated at the front of the rear vehicle, which effectively reduces drag on the driving vehicle. To elucidate this, a total of four vehicles were applied to platooning at a speed of 100 km/h by altering the gap distance of heavy-duty vehicles (HDVs) such as 0.5 Length (L), 1 L, 1.5 L, 2.0 L, and 2.5 L under the conditions of 1 L equal to 13.16 m. The stagnation pressure at the front of the following vehicle (FV) was reduced, and quantitative analysis of drag force generated at each leading vehicle (LV) and following vehicle that is platooning exhibited a reduction of about 51%, 56%, and 52%, respectively, when compared to the single moving HDV. This is considered as a reduction in engine power for the driving vehicle. Taken together, these results are effective in improving fuel efﬁciency and reducing CO 2 , a representative greenhouse gas, and predicting fuel and CO 2 reduction based on HDV annual mileage according to the highway conditions and logistics.


Introduction
Greenhouse gas reduction has emerged as one of the biggest global problems.The six primary greenhouse gases are CO 2 , CH 4 , N 2 O, HFCs, PFCs, and SF 6 , which cause the greenhouse effect.Among them, CO 2 was increased by 80% in annual emissions from 1970 to 2004.To reduce greenhouse gas (GHG) emissions, the world government has established decarbonization policies, and automobiles are moving away from internal combustion engines in line with policies.However, due to logistics on the road it would take a long time to change internal combustion engine vehicles to eco-friendly vehicles.Previous studies have examined actively utilizing aerodynamic characteristics to improve the fuel efficiency of internal combustion engines.Representatively, recent studies were performed on mounting an airfoil-shaped spoiler at the tail end of a vehicle [1], mounting a vortex generator [2], attempting to change the rear design of the vehicle [3], mounting an air duct [4], and securing the seal of the side window of the vehicle [5].In particular, research and development applying aerodynamic characteristics such as a roof fairing system is representative [6].Recently, as autonomous driving such as V2X (Vehicle-to-Everything) became an issue, European countries tried to solve the problem of air resistance that occurs during driving rather than reducing air resistance by changing the vehicle's exterior.For example, in 2011, the SARTRE project [7], an empirical study conducted for GHG reduction using the aerodynamic characteristics, occurred during platooning of the freight vehicles.However, the technology for controlling the distance between vehicles was not developed at that time, so the project could only confirm the possibility of GHG reduction through platooning.Therefore, the SARTRE project, an empirical study, researched controlling the distance between vehicles by lowering the freight vehicle to 6 m, thereby confirming the possibility of improving fuel economy and reducing GHG.Those effects lead to the reduction in logistics costs [8].In addition, the Korean government leads the Truck Platooning Project of Korea (TROOP) [9], an empirical study for platooning large freight vehicles.This project has been conducted to control the distance between vehicles at about 15 m.Based on V2X for the safety of autonomous vehicles, diversified platooning safety research is underway, such as distance control of ACC (Adaptive Cruise Control) [10], platooning for CACC (Cooperative Adaptive Cruise Control) [11,12], analysis of acceleration driving of lead vehicles during platooning [13], and emergency braking control [14].Previous studies demonstrated that platooning driving might contribute to an eco-friendly road environment by reducing air resistance.Therefore, the objective of this study is to understand the variation in aerodynamic characteristics of each model vehicle in platooning by analyzing the change in pressure and drag force of each vehicle in platooning.

Description of the Model Vehicle with Its Numerical Grid
In this study, we chose the SCANIA R-series heavy-duty vehicle with a 13.0 liter diesel engine with its maximum brake power, 500 hp.This model vehicle has been used for on-road tests for aerodynamic performance analysis of vehicle platooning in previous empirical studies, due to occupying a large position in the transportation and logistics market worldwide [15,16].The simplified model vehicle was used for this numerical study, and the solid model with the geometric dimensions 13.16 m × 2.495 m × 3.725 m (Length × Width × Heigth) is given in Figure 1.
Energies 2022, 15, x FOR PEER REVIEW 2 of 12 GHG reduction using the aerodynamic characteristics, occurred during platooning of the freight vehicles.However, the technology for controlling the distance between vehicles was not developed at that time, so the project could only confirm the possibility of GHG reduction through platooning.Therefore, the SARTRE project, an empirical study, researched controlling the distance between vehicles by lowering the freight vehicle to 6 m, thereby confirming the possibility of improving fuel economy and reducing GHG.Those effects lead to the reduction in logistics costs [8].In addition, the Korean government leads the Truck Platooning Project of Korea (TROOP) [9], an empirical study for platooning large freight vehicles.This project has been conducted to control the distance between vehicles at about 15 m.Based on V2X for the safety of autonomous vehicles, diversified platooning safety research is underway, such as distance control of ACC (Adaptive Cruise Control) [10], platooning for CACC (Cooperative Adaptive Cruise Control) [11,12], analysis of acceleration driving of lead vehicles during platooning [13], and emergency braking control [14].Previous studies demonstrated that platooning driving might contribute to an eco-friendly road environment by reducing air resistance.Therefore, the objective of this study is to understand the variation in aerodynamic characteristics of each model vehicle in platooning by analyzing the change in pressure and drag force of each vehicle in platooning.

Description of the Model Vehicle with Its Numerical Grid
In this study, we chose the SCANIA R-series heavy-duty vehicle with a 13.0 liter diesel engine with its maximum brake power, 500 hp.This model vehicle has been used for on-road tests for aerodynamic performance analysis of vehicle platooning in previous empirical studies, due to occupying a large position in the transportation and logistics market worldwide [15,16].The simplified model vehicle was used for this numerical study, and the solid model with the geometric dimensions 13.16 m × 2.495 m × 3.725 m (Length × Width × Heigth) is given in Figure 1.

Numerical Domain and Its Conditions
The numerical domain size was defined as shown in Figure 2. Especially, 8 L was given at the rear side of the last model vehicle for stable convergence on the simulation result.

Numerical Domain and Its Conditions
The numerical domain size was defined as shown in Figure 2. Especially, 8 L was given at the rear side of the last model vehicle for stable convergence on the simulation result.
GHG reduction using the aerodynamic characteristics, occurred during platooning of the freight vehicles.However, the technology for controlling the distance between vehicles was not developed at that time, so the project could only confirm the possibility of GHG reduction through platooning.Therefore, the SARTRE project, an empirical study, researched controlling the distance between vehicles by lowering the freight vehicle to 6 m, thereby confirming the possibility of improving fuel economy and reducing GHG.Those effects lead to the reduction in logistics costs [8].In addition, the Korean government leads the Truck Platooning Project of Korea (TROOP) [9], an empirical study for platooning large freight vehicles.This project has been conducted to control the distance between vehicles at about 15 m.Based on V2X for the safety of autonomous vehicles, diversified platooning safety research is underway, such as distance control of ACC (Adaptive Cruise Control) [10], platooning for CACC (Cooperative Adaptive Cruise Control) [11,12], analysis of acceleration driving of lead vehicles during platooning [13], and emergency braking control [14].Previous studies demonstrated that platooning driving might contribute to an eco-friendly road environment by reducing air resistance.Therefore, the objective of this study is to understand the variation in aerodynamic characteristics of each model vehicle in platooning by analyzing the change in pressure and drag force of each vehicle in platooning.

Description of the Model Vehicle with Its Numerical Grid
In this study, we chose the SCANIA R-series heavy-duty vehicle with a 13.0 liter diesel engine with its maximum brake power, 500 hp.This model vehicle has been used for on-road tests for aerodynamic performance analysis of vehicle platooning in previous empirical studies, due to occupying a large position in the transportation and logistics market worldwide [15,16].The simplified model vehicle was used for this numerical study, and the solid model with the geometric dimensions 13.16 m × 2.495 m × 3.725 m (Length × Width × Heigth) is given in Figure 1.

Numerical Domain and Its Conditions
The numerical domain size was defined as shown in Figure 2. Especially, 8 L was given at the rear side of the last model vehicle for stable convergence on the simulation result.The airflow field was assumed as a 3-dimensional steady incompressible and turbulent flow field for the numerical calculation.The details of the initial and boundary conditions are given in Table 1.The inlet was defined as the velocity boundary with the plugged flow condition, and the outlet was assumed as fully developed and defined as the pressure boundary with the ambient condition.The moving boundary was set to the ground with the same speed as the inlets.

Numerical Grid of the Physical Model
The CAD-to-CFD method [17] in conjunction with the orthogonal grid was used for the discretization of the physical domain in this study.First, the 3D CAD program, Pro-Engineers, was used as solid model of the vehicle and it was transferred into the numerical domain to generate the hexagonal meshes in the Cartesian coordinate system.
Figure 3 shows a typical grid in the numerical domain with four model vehicles keeping their distance (1 L) in between.For the optimum grid in the domain, the grid convergence test was conducted by thorough grid dependence evaluation with different iterations and very nicely converged with the cut-off error of the residual fraction of the main properties less than 0.01%.The optimum grid size was decided to be (658 × 99 × 87), and the total number of the grid was 5,667,354.
The airflow field was assumed as a 3-dimensional steady incompressible and turbulent flow field for the numerical calculation.The details of the initial and boundary conditions are given in Table 1.The inlet was defined as the velocity boundary with the plugged flow condition, and the outlet was assumed as fully developed and defined as the pressure boundary with the ambient condition.The moving boundary was set to the ground with the same speed as the inlets.

Numerical Grid of the Physical Model
The CAD-to-CFD method [17] in conjunction with the orthogonal grid was used for the discretization of the physical domain in this study.First, the 3D CAD program, Pro-Engineers, was used as solid model of the vehicle and it was transferred into the numerical domain to generate the hexagonal meshes in the Cartesian coordinate system.
Figure 3 shows a typical grid in the numerical domain with four model vehicles keeping their distance (1 L) in between.For the optimum grid in the domain, the grid convergence test was conducted by thorough grid dependence evaluation with different iterations and very nicely converged with the cut-off error of the residual fraction of the main properties less than 0.01%.The optimum grid size was decided to be (658 × 99 × 87), and the total number of the grid was 5,667,354.

Numerical Scheme and Its Condition
The general-purpose FVM (finite volume method) CFD code, PHOENICS (ver.2020), was used for a numerical calculation of the turbulent incompressible flow field.The 3dimensional Naiver-Stokes equations were solved with the KECHEN turbulent model (Chen-Kim κ-ε model), a modified standard κ-ε turbulent model that had good agreement with experimental data [18].The turbulent no-slip condition near the solid boundary was modeled by logarithmic law.
The airflow field for the analysis was defined as follows:

Governing Equations
The governing equation for the steady, incompressible, and turbulent flow fields is given below: (1) Continuity equation:

Numerical Scheme and Its Condition
The general-purpose FVM (finite volume method) CFD code, PHOENICS (ver.2020), was used for a numerical calculation of the turbulent incompressible flow field.The 3dimensional Naiver-Stokes equations were solved with the KECHEN turbulent model (Chen-Kim κ-ε model), a modified standard κ-ε turbulent model that had good agreement with experimental data [18].The turbulent no-slip condition near the solid boundary was modeled by logarithmic law.
The airflow field for the analysis was defined as follows: • Quasi-3D flow.

Governing Equations
The governing equation for the steady, incompressible, and turbulent flow fields is given below: (1) Continuity equation: (2) Momentum equation: where (3) κ-ε turbulent energy model (KECHEN); -Turbulent kinetic energy equation: where G = −u i u j ε .-Energy dissipation equation: where v t is turbulent kinematic viscosities, σ k , σ Prandtl number connected to the diffusivity of K and ε to eddy viscosity [18].

Aerodynamic Pressure Drag
The drag force (F D ) and drag coefficient (C D ) of the model vehicle are calculated using the following equations.
-Drag force (F D ) where A y is the projected area of the model vehicle in the longitudinal direction.

Traction Power Saved on Each Model Vehicle Platooning
The reduction in the tractive power of each model vehicle platooning compared to the single moving vehicle (SV) can be calculated by Equation (7) [19].

Fuel Saved on Each Model Vehicle Platooning Compared to SV
The mass flow rate of the fuel saved by the aerodynamic reduction can be calculated with the power saved as follows: -Fuel mass and volume flow rate, . .
m fuel /ρ fuel (9) where, Q LHV , ρ fuel are the lower heating value and density of diesel fuel, η engine is the brake thermal efficiency of the diesel engine.The values are given in Table 2.

Aerodynamics Characteristics of the Model Vehicles in Platooning
The C D of the leading vehicle (LV) is 0.6 at 0.5 L condition, which is 15% lower than the single vehicle moving (SV) (Table 3).It is due to the rear pressure recovery because of the higher stagnation pressure formed on the frontal surface of the following vehicle (FV1).However, the C D of LV does not change much under the different distance conditions.However, FV1, FV2, and FV3 have a serious reduction in C D, and the average reduction compared to SV is about 44% which is similar to the results reported in the previous study [24].
Figure 4 shows the variation in C D of each model vehicle in platooning with the change in gap.The LV in platooning has the highest drag coefficient in all gaps but the averaged C D (Figure 4) is still lower than the SVs (0.71).The drag decreases continuously as the distance between the model vehicles is shortened.Figure 4 shows the variation in CD of each model vehicle in platooning with the change in gap.The LV in platooning has the highest drag coefficient in all gaps but the averaged CD (Figure 4) is still lower than the SVs (0.71).The drag decreases continuously as the distance between the model vehicles is shortened.Figure 5 shows the averaged reduction in CD of each vehicle platooning compared to the SV.As shown, the front leading vehicle has only 3.3% less drag than the SV and the drag drops significantly from the 2nd vehicle (FV1) and the reduction reaches 46.9% on the last-placed vehicle (FV3) (Figure 5).  Figure 5 shows the averaged reduction in C D of each vehicle platooning compared to the SV.As shown, the front leading vehicle has only 3.3% less drag than the SV and the drag drops significantly from the 2nd vehicle (FV1) and the reduction reaches 46.9% on the last-placed vehicle (FV3) (Figure 5). Figure 4 shows the variation in CD of each model vehicle in platooning with the change in gap.The LV in platooning has the highest drag coefficient in all gaps but the averaged CD (Figure 4) is still lower than the SVs (0.71).The drag decreases continuously as the distance between the model vehicles is shortened.Figure 5 shows the averaged reduction in CD of each vehicle platooning compared to the SV.As shown, the front leading vehicle has only 3.3% less drag than the SV and the drag drops significantly from the 2nd vehicle (FV1) and the reduction reaches 46.9% on the last-placed vehicle (FV3) (Figure 5). Figure 6 shows the static pressure distribution around the vehicles platooning and it indicates that the stagnation pressure is highest at the front surface of the LV and gradually decreases for the following vehicles because the incoming air velocity decreases due to the circulation flow at the front region of each following vehicle.Table 3 shows that LV has 15% lower drag than the SV under the 0.5 L condition.It is due to the higher station pressure formed on the frontal region of FV1 which recovers the rear pressure of the LV.Additionally, the effect disappears as the gap distance increases.
Figure 6 shows the static pressure distribution around the vehicles platooning and it indicates that the stagnation pressure is highest at the front surface of the LV and gradually decreases for the following vehicles because the incoming air velocity decreases due to the circulation flow at the front region of each following vehicle.Table 3 shows that LV has 15% lower drag than the SV under the 0.5 L condition.It is due to the higher station pressure formed on the frontal region of FV1 which recovers the rear pressure of the LV.Additionally, the effect disappears as the gap distance increases.It is caused by the lower stagnation pressure formed on the frontal face of each model vehicle in platooning (Figure 6) and the lower turbulent kinetic energy formed at the rear side of each model vehicle (Figure 7). Figure 8 shows the turbulent kinetic energy distribution between the model vehicles with the different gaps.As the gap is shorter, the kinetic energy formed between the vehicles is higher and it is the reason for the lower static pressure formed in the gap, and it contributes to the lower stagnation pressure formed on the frontal face of the following vehicles.The drag force on a moving vehicle generates air resistance due to the pressure difference between the front and rear sides of the vehicle.When two vehicles are moving in parallel, a serious vortex is generated at the rear side of the front vehicle as shown in Figure 7.This complicated flow phenomenon decreases the stagnation pressure on the front side of the following vehicle and decreases air resistance on it.
to the circulation flow at the front region of each following vehicle.Table 3 shows that LV has 15% lower drag than the SV under the 0.5 L condition.It is due to the higher station pressure formed on the frontal region of FV1 which recovers the rear pressure of the LV.Additionally, the effect disappears as the gap distance increases.It is caused by the lower stagnation pressure formed on the frontal face of each model vehicle in platooning (Figure 6) and the lower turbulent kinetic energy formed at the rear side of each model vehicle (Figure 7). Figure 8 shows the turbulent kinetic energy distribution between the model vehicles with the different gaps.As the gap is shorter, the kinetic energy formed between the vehicles is higher and it is the reason for the lower static pressure formed in the gap, and it contributes to the lower stagnation pressure formed on the frontal face of the following vehicles.It is caused by the lower stagnation pressure formed on the frontal face of each model vehicle in platooning (Figure 6) and the lower turbulent kinetic energy formed at the rear side of each model vehicle (Figure 7).
Figure 8 shows the turbulent kinetic energy distribution between the model vehicles with the different gaps.As the gap is shorter, the kinetic energy formed between the vehicles is higher and it is the reason for the lower static pressure formed in the gap, and it contributes to the lower stagnation pressure formed on the frontal face of the following vehicles.

Fuel Efficiency and GHG Emission Improvement in the Model Vehicles
According to the research reports from the EU FT7 (SARTRE project, 2016), it was found that close distance between the vehicles in platooning improves the fuel efficiency for all vehicles [24].In the case of a 6 m gap, which is half-length of the model HDV, the LV saved 8% of fuel compared to SV and up to 16% for the following FV [25].We also predicted fuel consumption and GHG reduction in this study.

Fuel Efficiency and GHG Emission Improvement in the Model Vehicles
According to the research reports from the EU FT7 (SARTRE project, 2016), it was found that close distance between the vehicles in platooning improves the fuel efficiency for all vehicles [24].In the case of a 6 m gap, which is half-length of the model HDV, the LV saved 8% of fuel compared to SV and up to 16% for the following FV [25].We also predicted fuel consumption and GHG reduction in this study.
Figure 9 shows the tractive power saved by the vehicles platooning compared to the single moving vehicle (SV).For the leading vehicle (LV), the power energy was not saved much compared to SV but from the 2nd vehicle (FV1, FV2, FV3) the tractive power distinctively decreased.The power saved on the model vehicles platooning versus SV was calculated with Equation (7).LV saved approximately 10 kW of power at the 0.5 L gap condition.Under 1.0 L~2.5 L gap conditions, a relatively narrower gap does result in a better traction power reduction than SV, and the power saved increases as the location of the model vehicle is far from the leading position.When the HDV's gap is 0.5 L, the averaged traction power saved for FV1, FV2, and FV3 is 38 kW compared to the SV.Additionally, the FVs kept an average of 30 kW of power under the condition of the 1.0 L~2.5 L gap. Figure 9 shows the tractive power saved by the vehicles platooning compared to the single moving vehicle (SV).For the leading vehicle (LV), the power energy was not saved much compared to SV but from the 2nd vehicle (FV1, FV2, FV3) the tractive power distinctively decreased.The power saved on the model vehicles platooning versus SV was calculated with Equation (7).

Fuel Efficiency and GHG Emission Improvement in the Model Vehicles
According to the research reports from the EU FT7 (SARTRE project, 2016), it was found that close distance between the vehicles in platooning improves the fuel efficiency for all vehicles [24].In the case of a 6 m gap, which is half-length of the model HDV, the LV saved 8% of fuel compared to SV and up to 16% for the following FV [25].We also predicted fuel consumption and GHG reduction in this study.
Figure 9 shows the tractive power saved by the vehicles platooning compared to the single moving vehicle (SV).For the leading vehicle (LV), the power energy was not saved much compared to SV but from the 2nd vehicle (FV1, FV2, FV3) the tractive power distinctively decreased.The power saved on the model vehicles platooning versus SV was calculated with Equation (7).LV saved approximately 10 kW of power at the 0.5 L gap condition.Under 1.0 L~2.5 L gap conditions, a relatively narrower gap does result in a better traction power reduction than SV, and the power saved increases as the location of the model vehicle is far from the leading position.When the HDV's gap is 0.5 L, the averaged traction power saved for FV1, FV2, and FV3 is 38 kW compared to the SV.Additionally, the FVs kept an average of 30 kW of power under the condition of the 1.0 L~2.5 L gap.LV saved approximately 10 kW of power at the 0.5 L gap condition.Under 1.0 L~2.5 L gap conditions, a relatively narrower gap does result in a better traction power reduction than SV, and the power saved increases as the location of the model vehicle is far from the leading position.When the HDV's gap is 0.5 L, the averaged traction power saved for FV1, FV2, and FV3 is 38 kW compared to the SV.Additionally, the FVs kept an average of 30 kW of power under the condition of the 1.0 L~2.5 L gap.
The fuel savings for each model vehicle platooning compared to SV was calculated with Equations ( 8)- (10).
The fuel consumption of SV by aerodynamic resistance was calculated as 5.2 km/liter at 100 km/h from Equation (10).When a single vehicle was moving, the fuel efficiency of FV1, FV2, and FV3 can be predicted as shown in Table 4.As a result, among simulation cases, the possibility of increasing the fuel efficiency of FV 1, 2, and 3 to 10 km/L is also confirmed under the 0.5 L conditions with maximum aerodynamic effects (100 km/h cruising driving condition).According to KOTI (The Korea Transport Institute) report.2021, Vol.62, the average daily driving distance of a loaded HDV was about 300 km/day in Korea for 2020 [26].The averaged cruising speed of the HDV on a highway is 100 km/h; thus, the daily drive time is 3 h.
Based on HDV's gap of 0.5 L, LV kept 2100 liter per year compared to SV.The saved result of an average of 7435 liter of FVs is shown in Figure 10.CO 2 reduction is calculated through Equation ( 11), resulting in LV saved by 5.3 tons per year and FVs saved by an average about 18.8 tons per year compared to the SV (Figure 11).
The fuel consumption of SV by aerodynamic resistance was calculated as 5.2 km/liter at 100 km/h from Equation (10).When a single vehicle was moving, the fuel efficiency of FV1, FV2, and FV3 can be predicted as shown in Table 4.As a result, among simulation cases, the possibility of increasing the fuel efficiency of FV 1, 2, and 3 to 10 km/L is also confirmed under the 0.5 L conditions with maximum aerodynamic effects (100 cruising driving condition).According to KOTI (The Korea Transport Institute) report.2021, Vol.62, the average daily driving distance of a loaded HDV was about 300 km/day in Korea for 2020 [26].The averaged cruising speed of the HDV on a highway is 100 km/h; thus, the daily drive time is 3 h.
Based on HDV's gap of 0.5 L, LV kept 2100 liter per year compared to SV.The saved result of an average of 7435 liter of FVs is shown in Figure 10.CO2 reduction is calculated through Equation ( 11), resulting in LV saved by 5.3 tons per year and FVs saved by an average about 18.8 tons per year compared to the SV (Figure 11).Thus, reducing drag force from the platoon can reduce the power required by the engine, resulting in reduced fuel consumption and GHG.Furthermore, aerodynamic drag is proportional to the square of vehicle speed, so high speed platooning could be more Thus, reducing drag force from the platoon can reduce the power required by the engine, resulting in reduced fuel consumption and GHG.Furthermore, aerodynamic drag is proportional to the square of vehicle speed, so high speed platooning could be more effective in saving energy.

Conclusions
This numerical study aimed to understand the aerodynamic effect of the heavy-duty vehicles platooning with the change in the platooning conditions; the gap between the model vehicles and the platooning position of the model vehicle.With the platooning condition change, aerodynamic resistance was analyzed to have the possibility of GHG emission reductions and fuel efficiency improvement.This study only considered steady driving conditions on a level road with no side wind.In addition, the aerodynamic characteristics of the vehicle were theoretically analyzed to determine the energy saving of the vehicle.Further study is needed to analyze the real driving state.From the research, the following were found: i.
The stagnation pressure of FV is reduced due to the rear vortex generated by the front leading vehicle.This is the main cause of the drag reduction on the FV.In this study, the drag of FVs was reduced over 50% compared to SV at the gap (0.5 L) (Table 3).ii.The shorter the gap between the model vehicles platooning, the smaller C D of FV, which indicates the shorter the gap distance, the more significant the influence of vortex on the FV.As the gap between the model vehicles widens, the rear vortex of the LV gradually decreases and the static pressure recovers to the ambient pressure.It is the reason for increasing the stagnation pressure of FV causing to C D increase.iii.Platoon driving has very positive effect not only to the fuel savings but also on the GHG reduction.Thus, the platoon driving mode of heavy-duty vehicles would seriously contribute to the logistics industry, economically and environmentally.iv.This study hypothesized the driving conditions of autonomous vehicles based on V2X and suggested that the aerodynamic effect can be maximized when an appropriate platoon gap is set in vehicle-to-vehicle distance control.However, this study aimed to confirm the possibility of reducing GHG according to the platooning concept.v.
This study performed a theoretical analysis using the FVM numerical simulation method.Platooning simulations were performed under the steady driving condition on a level road with no side wind to determine the fuel economy effect so this study might be used for reference.In future research, we will undertake the aerodynamic driving stability research on vehicle platooning.In the study, the weight of the vehicle with the road condition such as the friction coefficient and slippery factor of the road and the side wind, the gyration radius of the road with the tilted angle, etc., should be the important parameters to evaluate the road-load power for the study.

Figure 1 .
Figure 1.A perspective view of the simplified model vehicle with its dimensions.

Figure 2 .
Figure 2. Numerical domain with the model heavy-duty vehicles platooning.

Figure 1 .
Figure 1.A perspective view of the simplified model vehicle with its dimensions.

Figure 1 .
Figure 1.A perspective view of the simplified model vehicle with its dimensions.

Figure 2 .
Figure 2. Numerical domain with the model heavy-duty vehicles platooning.Figure 2. Numerical domain with the model heavy-duty vehicles platooning.

Figure 2 .
Figure 2. Numerical domain with the model heavy-duty vehicles platooning.Figure 2. Numerical domain with the model heavy-duty vehicles platooning.

Figure 4 .
Figure 4. Variation in drag coefficient (CD) of each model vehicle in platooning with the change in the gap.

Figure 4 .
Figure 4. Variation in drag coefficient (C D ) of each model vehicle in platooning with the change in the gap.

Figure 4 .
Figure 4. Variation in drag coefficient (CD) of each model vehicle in platooning with the change in the gap.

Figure 5 .
Figure 5. Reduction in the averaged C D of each vehicle in platooning compared to SV.

Figure 6 .
Figure 6.Comparison of the static pressure distribution with the change in the gap at 100 km/h.The drag force on a moving vehicle generates air resistance due to the pressure difference between the front and rear sides of the vehicle.When two vehicles are moving in parallel, a serious vortex is generated at the rear side of the front vehicle as shown in Figure 7.This complicated flow phenomenon decreases the stagnation pressure on the front side of the following vehicle and decreases air resistance on it.It is caused by the lower stagnation pressure formed on the frontal face of each model vehicle in platooning (Figure6) and the lower turbulent kinetic energy formed at the rear side of each model vehicle (Figure7).

Figure 7 .
Figure 7. Vortex generated in between LV and FV1 at 0.5 L and 100 km/h in speed.

Figure 6 .
Figure 6.Comparison of the static pressure distribution with the change in the gap at 100 km/h.

Figure 6 .
Figure 6.Comparison of the static pressure distribution with the change in the gap at 100 km/h.The drag force on a moving vehicle generates air resistance due to the pressure difference between the front and rear sides of the vehicle.When two vehicles are moving in parallel, a serious vortex is generated at the rear side of the front vehicle as shown in Figure 7.This complicated flow phenomenon decreases the stagnation pressure on the front side of the following vehicle and decreases air resistance on it.It is caused by the lower stagnation pressure formed on the frontal face of each model vehicle in platooning (Figure6) and the lower turbulent kinetic energy formed at the rear side of each model vehicle (Figure7).

Figure 7 .
Figure 7. Vortex generated in between LV and FV1 at 0.5 L and 100 km/h in speed.

Figure 7 .
Figure 7. Vortex generated in between LV and FV1 at 0.5 L and 100 km/h in speed.

Figure 8 .
Figure 8.Comparison of the turbulent kinetic energy distribution with the change in the gap at 100 km/h.

Figure 9 .
Figure 9. Tractive power (PWsaved) saved on the vehicles platooning compared to SV at 100 km/h.

Figure 8 .
Figure 8.Comparison of the turbulent kinetic energy distribution with the change in the gap at 100 km/h.

Figure 8 .
Figure 8.Comparison of the turbulent kinetic energy distribution with the change in the gap at 100 km/h.

Figure 9 .
Figure 9. Tractive power (PWsaved) saved on the vehicles platooning compared to SV at 100 km/h.

Figure 9 .
Figure 9. Tractive power (PW saved ) saved on the vehicles platooning compared to SV at 100 km/h.

Figure 10 .
Figure 10.Annual fuel saving on the model vehicles platooning compared to the single moving vehicle (SV) at a 0.5 L gap.Figure 10.Annual fuel saving on the model vehicles platooning compared to the single moving vehicle (SV) at a 0.5 L gap.

Figure 10 . 12 Figure 11 .
Figure 10.Annual fuel saving on the model vehicles platooning compared to the single moving vehicle (SV) at a 0.5 L gap.Figure 10.Annual fuel saving on the model vehicles platooning compared to the single moving vehicle (SV) at a 0.5 L gap.Energies 2022, 15, x FOR PEER REVIEW 10 of 12

Figure 11 .
Figure 11.Annual CO 2 reduction in platooning vehicle driving compared to the single moving vehicle (SV) at a 0.5 L gap.

Table 1 .
Boundary and initial conditions on the control volume.

Table 1 .
Boundary and initial conditions on the control volume.
i : the amount of incinerated fossil liquid waste type i,[Gg].CL i : carbon content of fossil liquid waste type i, (fraction).OF i : oxidation factor for fossil liquid waste type i, (fraction).44/12: conversion factor from C to CO 2 .

Table 3 .
Variation in drag coefficient of the model vehicle with the gap and the position.

Table 4 .
Fuel mileage of each model vehicle platooning compared to the single moving vehicle (SV).

Table 4 .
Fuel mileage of each model vehicle platooning compared to the single moving vehicle (SV).