Gasiﬁcation of Psidium guajava L. Waste Using Supercritical Water: Evaluation of Feed Ratio and Moderate Temperatures

: Biomass waste, as raw material for renewable energy, is an attractive alternative since it does not compete with human food supply. An emerging alternative for its treatment is supercritical water gasiﬁcation (SCWG), due to the high moisture content of some types of biomass. On this regards, guava fruit ( Psidium guajava L.) is one of the most wasted agro-food products in Mexico. This motivated us to evaluate gasiﬁcation of guava waste on dry biomass base under supercritical water conditions for the ﬁrst time, with the aim of analyzing the impact of moderate temperatures and feed ratios as reaction parameters on gas products. Temperature was varied in the range of 673.15–773.15 K and using a batch reactor loaded with biomass:water (B:W) mass ratios of 1:1, 1:4, and 1:6. Furthermore, the obtained solid, liquid, and gas phase products were characterized. Hydrogen (H 2 ), carbon dioxide (CO 2 ), carbon monoxide (CO), methane (CH 4 ), ethane (C 2 H 6 ), propane (C 3 H 8 ), and butane (C 4 H 10 ) were identiﬁed in gas phase and quantiﬁed by means of a gas chromatograph equipped with a TCD detector. Liquid and solid phase products were subjected to Fourier Transform Infrared spectroscopy analyses. This preliminary research indicated that high temperature operation and high biomass:water mass ratio enhanced gas yields (mol/kg) of about 4.137 for CH 4 , 6.705 for CO 2 , and 7.743 for H 2 ; whereas the selectivity and gas efﬁciency for hydrogen was 65.26% and 58.94%, respectively. and O.E.-S.; data curation, R.G.-M. and S.O.F.-V.; writing—original draft preparation, S.G.-A., A.Z.-M., and O.E.-S.; writing—review and editing, O.E.-S.; visualization, O.E.-S.; supervision, A.Z.-M. and O.E.-S.; project administration, O.E.-S.; funding acquisition, A.Z.-M.


Introduction
Gasification via supercritical water is an alternative technology in gasification of biomass with high moisture content. Some remarkable aspects for reactions in SCWG are the lower operating temperature in comparison with the corresponding for conventional gasification or pyrolysis, the suitable solvating power for water focused on organic reactants, the inhibition of reactions as polymerization, and the high hydrogen-production in detriment of carbon monoxide content at high temperatures.
A great variety of biomass has water content higher than 80%. SCWG processes exhibit some advantages due to the supercritical water properties (critical temperature, 647.10 K; critical pressure, 22.06 MPa), such as high diffusion rates, low viscosity, and low dielectric constant. These characteristics make water an excellent solvent for organic materials, and takes part on the hydrogen bonds weakening to contribute hydrogen production [1]. Nowadays, organic/inorganic residues have been highlighted because its exploitation can generate value-added products instead of waste disposal. In this concern, waste biomass can be used as wet feedstock for fuel gas generation. The exploitation of renewable resources to produce less-pollutant fuels are a solution to avoid complete dependence on fossil fuels since combustion of petroleum fractions provokes environmental pollution by greenhouse gases.
Regarding the Mexican agricultural sector, a serious problem on post-harvest crop products is the huge losses on fruits during the food production chain stages (from farmers to final customers). Based on official reports from the Secretary of Social Development (Secretaría de Desarrollo Social, Mexico) in 2015, the total food waste was 10,000,431 tons per year equivalent to 37.26% of total production. Guava fruit (Psidium guajava L.) was the most wasted fruit in Mexico, about 57.70% of its national production [2], which creates an opportunity area for this waste. It can be treated via diverse chemical processes to generate high value-added products.
Taking advantage of water content, biomass waste can be utilized in a gasification process using supercritical water to obtain gaseous fuels or syngas, (which contains hydrogen) depending on the operation conditions. Water would act as solvent and reactant at supercritical conditions; hence, biomass might not require rigorous pretreatment. The first approaches have studied SCWG with model compounds (lignin, fructose, cellulose, hemicellulose, and glucose). Furthermore, vast efforts have been carried out using organic or inorganic "real" biomass, such as plastic material, petroleum fractions, municipal or industrial wastewater, and sludge, as well as some organic residues from agricultural, animal, and food sectors. About experiments, fuel synthesis has been performed above critical temperature of water up to 1123 K in catalytic/non-catalytic batch or continuous flow reactors made of different materials. All these parameters are aimed to describe the reaction mechanism, look for the optimum operating conditions, and perform numerical simulation [3][4][5][6][7][8][9][10][11][12][13][14][15].
Composition and content of products via SCWG depend on the reaction conditions and biomass composition. For instance, lignocellulosic biomass is typically constituted by cellulose (45-50%), hemicellulose (20-25%) and lignin (20-25%). The reaction mechanism that induces water is complex at these conditions, as demonstrated elsewhere [3][4][5][6][7][8][9][10][11][12][13][14][15]. Initially, biomass material conversion produces intermediates by hydrolysis and the water solvating power effect. Consequently, these compounds are fragmented and cracked to produce gaseous components and small molecules [16]. The overall reaction can be summarized according to Equation (1), focused on hydrogen [17,18]: Specific reactions for gas production are steam reforming, hydrolysis, reforming, watergas shift, thermal decomposition, hydro-pyrolysis, oxidation, hydrogenation, methanation, and polymerization. The improvement or decreasing of these reactions is clearly dependent on temperature, biomass:water concentration, and biomass nature. The most important are: Steam reforming Concerning reutilization of real waste biomass. Some agro-food residues that have been studied elsewhere on dry or wet basis under supercritical water gasification are fruit pulp, peach scrap, aloe vera rind, coconut shell, sugarcane bagasse, malt spent grains, biooil, food waste, and peel from banana, lemon, orange, or pineapple. In certain applications, those biomasses were gasified under activated carbon, Ru/C, K 2 CO 3 , NaOH, KHCO 3 , Na 2 CO 3 , KOH, FeCl 3 and nickel-base materials as catalysts, even dosing additives in food waste feedstocks [19][20][21][22][23][24][25][26][27][28][29][30]. For the best of our knowledge, Silveira-Junior et al. have recently carried out fast pyrolysis from seed guava in the range of 623.15-873.15 K focused on levoglucosan. Biochar production raised at low temperature, the opposite occurred with liquid-phase generation whose maximum was attained at high temperature, whereas carbon dioxide was in the interval of 2.51-5.15% [31]. Therefore, our interest is centered in valorization of guava fruit waste under SCWG. The goal of our current study was to evaluate the effect of moderated temperatures (673.15-773.15 K) and biomass concentration (1:1, 1:4, 1:6) on the value-added chemicals yielded in gas, liquid and solid phases. As first approach, guava fruit waste was used in dry base biomass.

Materials and Methods
Overripe pink guava fruit (Psidium guajava L.) was collected from the state of Morelos, Mexico. The moisture content was achieved by a 915 KF Ti-Touch (Metrohm, Switzerland). The fruits were dehydrated in an oven and grinded up with the aim of avoiding an heterogenous sample lot. Biomass dry particles were estimated to have a geometric mean diameter of 0.624 mm. The water was distilled-grade and sulfuric acid was analytical grade (95-98%). Chemicals used as standards for calibration of analytical instrument were of high purity.
The particle size distribution of guava fruit was evaluated based on ASABE standard method S319.4 [32] of determining and expressing fineness of feed materials by sieving. Afterwards, biomass was characterized by ash content as per ASTM E-1755-95 standard test method, insoluble dietary fiber based on the method proposed by Claye et al. [33], high heating value (HHV) performed in a 6200 bomb calorimeter (Parr, USA), elemental C, O, H, N, S analysis carried out with a FLASH 2000 (Thermo Scientific, USA), total organic carbon (TOC) content by using a TOC-L (Shimadzu, Japan), and a Frontier FT-IR spectroscopy (PerkinElmer, USA) using 2 cm −1 of resolution. Thermogravimetric analysis (TGA) and differential calorimetry scanning (DSC) were performed on a STA PT 1000 (Linseis, Germany) at a heating rate of 11 K/min in a temperature range from 298.15 to 853.15 K and under argon atmosphere. The TGA allowed estimating the devolatilization behavior of the guava fruit waste by calculating the differential weight loss.
Supercritical water gasification reactions were conducted in a batch reactor made of Inconel 625 alloy. A schematic diagram is illustrated in Figure 1  Supercritical water gasification of guava fruit waste consisted on feeding into the reactor 100 g of mixture constituted by water and biomass on dry base, different biomass:water mass ratio were evaluated (B:W = 1:1, 1:4, 1:6), in order to reach high pressure conditions reported in the interval of 25.0-45.0 MPa. Weightings were measured in an analytical balance. Then, the reactor was hermetically sealed, and air was evacuated throughout a vacuum pump. Afterwards, the reactor was heated by an electrical furnace at a rate of 4 K/min to reach the desired temperature in the range of 673.15-773.15 K. Reaction conditions were kept for 60 min until the desired temperature was attained. Operating pressure depended on the temperature and the total volume of the biomass:water. Finally, the reaction was stopped by removing the reactor from the electrical heating resistance and a sudden cooling down to room temperature. Experiments were duplicated in order to check reliable conditions and results are reported as the average of repetitive runs.
Products were obtained in gas, liquid, and solid phases and were quantified gravimetrically in an analytical balance. The upper needle valve was opened to allow the gas flows throughout the stainless-steel filter and subsequently the molecular sieve 5A trap, to suppress the presence of solids and moisture. Then, the dried gas was collected in a high-pressure cell for weighing purposes.
The reactor was opened by removing the cover to gather liquid and solid residues. Preliminary experiments demonstrated the formation of four-phases: gas, aqueous, organic liquid, and solid; Nevertheless, the formation of two liquid phases was avoided in the reported results by adding two drops of sulfuric acid in liquid-phase. Hence, the ionization of organic acids and the formation of additional insoluble materials was inhibited. The liquid and solid were separated, the first one was filtered, and the second one was subject to evaporation.
The composition of gas effluent was analyzed in a gas chromatograph GC-7890B (Agilent, USA) equipped with a TCD detector and two columns; RT-XL packed and molsieve 13x capillary columns connected in series with argon as carrier gas. Temperatures for the TCD and injector were 523.15 K. The temperature gradient for the oven was set initially to 313.15 K for 4 min, and then a rate of 15 K/min was applied to reach 513.15 K for 11 min, followed by another ramp of 30 K/min set to reach 393.15 K during 2.6 min. Finally, gas compounds were quantified by external calibration of the TCD, evaluating the retention times using pure compounds as standards. Liquid products were characterized qualitatively and quantitatively by FT-IR spectroscopy and total organic carbon (TOC), in that order. Meanwhile solid phase was analyzed by FT-IR.

Biomass Characterization
Guava sample was subject to moisture content on wet basis. The remaining characterization results on dry basis such as geometric mean diameter (gmd), ash content, high heating value, TOC content, as well as ultimate and structural analyses are also listed in Table 1. The lignocellulosic biomass had a great content in C and O, low content in hydrogen, and slight amount of nitrogen and sulfur. The structure was predominantly constituted by hemicellulose and lignin with low content of cellulose. Some of these parameters are reported elsewhere by different research groups [34,35]. The thermal exposure of guava under atmospheric pressure was studied by thermogravimetric analysis and differential scanning calorimetry. Sample weight loss was recorded as increasing temperature to obtain thermograms and differential thermogravimetric curves at controlled heating rate as depicted in Figure 2. The combustion process profile depended on the composition and nature of sample. The organic matter was broken down into stages: drying, as well as active and passive pyrolysis. The organic biomass devolatilization profile were separated into several temperature-dependent zones. The first zone for the TGA curve had a weight loss of 8.85% up to around 440.15 K, caused by the release of moisture and volatile compounds. Afterwards, the second zone covered a slope in the interval from 440.15 K to 618.15 K, which represented a weight loss of 45.46%. It was associated with the devolatilization of components hemicellulose and cellulose degradation took place as well as lignin combustion. Hemicellulose was easier to be degraded than the others at these temperatures since it is mainly constituted by saccharides with amorphous structures, rich in branches. The last zone showed different slopes that began at 618.15 up to 853.15 K whose weight loss was about 33.41%. Lignin decomposition ended and was the main biomolecule that promoted biochar formation. The greater thermal stability on lignin structure was demonstrated compared with cellulose and hemicellulose. Besides, aromatic compounds predominated since the C-C bonds in phenylpropane [36,37].
The behavior of the differential scanning calorimetry analysis exhibited two endothermic broad peaks related to the energy required for evaporating moisture at 353.15 K and volatile compounds at 443.15 K. Energy release occurred at 573.15 K, which confirmed the degradation of hemicellulose and cellulose, as well as lignin, but partially [37][38][39]. Afterwards, four additional devolatilization sharp peaks were observed at 723.15, 743.15, 763.15, and 823.15 K; these could still be produced by the thermal decomposition of the remaining lignin [39,40]. Besides, the rupture of biomolecules (depolymerization reactions) such as xylan [41,42], biochar formation [43] and gas release [39,42,44], the combustion of complex branched (including aromatic rings), thermal stable structures [39,44], and ash [39][40][41][42][43][44][45] could contribute within this intense exothermic energy. Temperatures higher than 853.15 K were not tested since no significant peaks have not been reported previously based on the analysis carried out by Athmaselvi et al. [46].
Guava samples were also analyzed by Fourier Transform Infrared spectroscopy, a representative spectrum is illustrated in Figure 3 where the adsorption bands were associated with the functional groups of complex compounds. Emphasis was made on the polysaccharides listed in Table 2 as cellulose, hemicellulose, and lignin, but the samples also contained other components identified elsewhere like pectin, proteins, and flavonoids [47][48][49][50].   [53,69] The strong broad peak at 3273 cm −1 denoted the phenolic and aliphatic hydroxyl group stretching vibration; NH stretching of the amine group indicated the amino acid components [50][51][52][53][54]. The CH 2 asymmetrical and symmetrical stretching for alkane groups were associated with the medium peak at 2921 cm −1 and the weakness signal at 2850 cm −1 , respectively [47,52,53]. The weak peak around 1730 cm −1 corresponded to the carbonyl C=O stretching vibration of different groups such as acetyl, aldehydes, ketones and carboxylic acids [47,50,55,56]. The stretch of the carbonyl (C=O) conjugated with the aromatic skeleton of phenylpropane appeared for the medium signal at 1600 cm −1 of wavelength [55][56][57][58]. The weak signal at 1420 cm −1 indicated CH 3 bending vibrations, CH 2 symmetrical deformations and C-H in plane deformation with aromatic structure vibration [56,57,[59][60][61]. The relative weakness that lied at 1371 cm −1 was ascribed to C-H bending of alkanes [56,[59][60][61][62]. The signal at 1335 cm −1 was associated with OH in-plane bending and CH 2 wagging of alcohols and alkanes [55,56,63]. The sharp signal noticed at 1237 cm −1 corresponded to C-O, C-O-C bonds indicating the presence of carboxylic acids and ethers [53,64,65]. The weak peak observed at 1143 cm −1 presented aromatic C-H in plane bending, OH and C=O stretches [56,65]. The weak shoulder absorption band observed at 1098 cm −1 could be attributed to the C-O-H bending modes and C-O, suggesting the presence of alcohol groups [58,66]. The peak observed in 1047 cm −1 might be assigned to C 3 -O 3 H, and C-O stretching in C-O-C (ether) bonds [56,62,65,67]. The strongest sharp signal located around 1028 cm −1 was designated to C 6 -O 6 H, C-O, C=O, and C-C-O stretches denoting phenol, alcohol, and ester [50,52,55,65]. The 923 cm −1 weak signal indicated C-H out of plane for alkane group and aromatic [56,68]. The weak band sharpened at 869 cm −1 corresponded to deformation of the equatorial C 2 -H bond of mannosyl residue, and the narrow peak at 820 cm −1 presented C-H out plane bending [56,65,66]. The peak at 776 cm −1 could be assigned to deformation C-H in aromatic of carbohydrates and lignin [53,69].

Supercritical Water Gasification
Products obtained in gas, liquid, and solid phases from gasification under supercritical water were obtained from the complex mechanism where simultaneous or in-series phenomena and reactions are taking place. The main reactions: hydrolysis, decomposition, reforming, water-gas shift, methanation, hydrogenation, and polymerization were summarized in Equations (1)-(11) and explained by Okolie et al. [17] and Safari et al. [18]. The upgrade or inhibition of a particular reaction varied according to the experimental conditions. Products in gas phase from supercritical water gasification of waste guava fruit biomass evaluated at different conditions of mass ratio, temperature, and pressure are listed in Table 3 and depicted in Figure 4. The identified components, hydrogen, carbon dioxide, carbon monoxide, methane, ethane, propane, and butane, were analyzed by gas chromatography in terms of mole fraction (y i ) based on Equation (12), where n i is the mole amount (n) for each chemical species (i). Nitrogen and oxygen were not detected. y i (%) = n i /( ∑i n i ) × 100 (12)   Besides, gas yields were calculated according to Equation (13); their values are presented in Table 4.
gas yield (mol/kg) = n i /m feed (13) where m feed was referred to the mass of feed. In general, the lowest quantity was obtained for butane, and it was negligible in run R3. Carbon dioxide was the major component in all reactions, its highest content was reported at the lowest temperature and mass ratio; the mole fraction tended to decrease as mass ratio increased at fixed temperature and the opposite was observed at high temperatures at fixed mass ratio. Therefore, decarboxylation of acids and thermal decomposition were the dominant reactions among the others since a high rate of gasification of carbon and oxygen instead of hydrogen. Mole fraction for carbon monoxide was lower than 6.1%, it occurred at 673.15 K with 1:6 B:W mass ratio. The magnitude order for hydrocarbons was CH 4 > C 2 H 6 > C 3 H 8 > C 4 H 10 . Methane production was induced as temperature increases at 1:1 mass ratio; nevertheless, this behavior was not so remarkable at higher mass ratios because of three insights: the hydrogen production had been promoted, methanation was inhibited and nickel from reactor wall acted as catalyst during methane reforming. Significant changes were not identified for the other alkane quantities since steam reforming reaction and decompositions were taking place, but these were not so remarkable. Low hydrogen content was obtained at low mass ratio and the highest hydrogen production was obtained at 1:6 B:W mass ratio since high temperature and water content promoted the water-gas shift reaction in detriment of carbon dioxide formation. Temperature represented the greatest effect for obtaining gas since high temperature decreased solvent density drastically at supercritical conditions. Similar effect was caused in the ionic product promoting radical reactions such as hydrogenation, dealkylation, ring opening, polymerization by oligomer dehydrogenation. These reactions favored the structural compounds breakdown of biomass. In addition, high temperature upgraded energy needed to break carbon bonds and, hence, promoting the formation of light compounds such as methane and hydrogen.
Regarding carbon dioxide yield, the highest one was achieved at 773.15 K and 1:6 B:W mass ratio, but it diminished at lower temperature and mass ratio. Concerning H 2 and hydrocarbons, high temperature promoted raising on yields, but this parameter for ethane and heavier molecular weight hydrocarbons was so slight, besides low and variable yields for carbon monoxide were accomplished. The global yield was enhanced with temperature raising, so it would be suitable to explore higher temperature reactions.
The following parameters were calculated from gas quantification: hydrogen selectivity, hydrogen gasification efficiency (HGE), carbon gasification efficiency (CGE), and low heat value (LHV). Equations are detailed as follows: H 2 selectivity (%) = n H2 /(n CH4 + n CO2 + n CO + n C2H6 + n C3H8 + n C4H10 ) × 100 (14) HGE (%) = (4 n CH4 + 2 n H2 + 6 n C2H6 + 8 n C3H8 + 10 n C4H10 )/n H,feed × 100 CGE (%) = (n CH4 + n CO2 + n CO + 2 n C2H6 + 3 n C3H8 + 4 n C4H10 )/n C,feed × 100 The hydrogen selectivity calculated with Equation (14) is shown in Figure 5. Chemicals were subject to hydrolysis, reforming, and thermal decomposition. Monomers obtained from hydrolysis were subsequently involved in decomposition reactions to obtain low molecular weight chemicals, then these were decarboxylated to finally produce hydrogen and carbon dioxide The lowest selectivity was accomplished at low temperature and low mass ratio and it increased as mass ratio and temperature increased. The highest selectivity was reported at 773.15 K and 1:6 B:W mass ratio. This enhancement could be explained from an increase on bond cleavage, the bond gas products reactions, and the high water concentration. A better promoting effect on steam reforming and water-gas shift reactions could be occurring in comparison with CO or CO 2 methanation reactions. Hydrogen gas efficiency and carbon gas efficiency are depicted in Figure 6, both were calculated using Equation (15), Equation (16), respectively. HGE and CGE were promoted by temperature and mass ratio increments. The highest values for hydrogen were obtained at 773.15 K and 1:6 B:W mass ratio. Gas efficiency for hydrogen were higher than those for carbon at the same conditions except for the lowest B:W mass ratio, 1:1. Nevertheless, the studied conditions did not accelerate the biomass hydrolysis and further conversion of the more complex components. The temperature conditions did not allow the decomposition of refractory chemicals and hence higher yields and efficiencies. Finally, the LHV calculated based on Equation (17) is plotted in Figure 7 as a function of temperature and mass ratio. The lower LHV sets were observed for 1:1 in comparison with the other mass ratios. The low heat value tended to enhance in function of the mass ratio and temperature raising. Besides, the highest LHV was attained at highest temperature and mass ratio due to the high concentration and yield presented by H 2 at these conditions.

Liquid and Solid Products
Gasification also produced intermediates derived from incomplete conversion due to moderate temperatures. Some of them could be classified as ketones, aldehydes, alkanols, phenols, and carboxylic acids. The liquid-phase was initially obtained in different colors due to suspended solids; a yellowish mixture was gathered for all liquid samples after solid filtration. TOC analyses for the liquid-phase are shown in Figure 8. The TOC concentration was decreasing as temperature increased. Regarding the mass ratio, TOC concentration increased as water concentration was high. FT-IR spectra for liquid-phase products are illustrated in Figure 9. Two intense peaks were observed in the range of 3000-3600 cm −1 and at 1621 cm −1 . The first peak was associated to alcohol and carboxylic acid groups, and the second exhibited carboxylic acids, amides and heterocyclic compounds. Those analyses confirmed the presence of phenolic compounds and polycyclic aromatic hydrocarbons since refractory compounds could not be degraded at these the temperature conditions. Phenolic compounds were the most difficult chemicals to be decomposed and hence inhibited gas formation under supercritical water conditions. Besides, the high concentration of biomass on feed for 1:1 B:W mass ratio was not beneficial for a better gas yield during steam reforming or water-gas shift reactions since these reactions needed sufficient water as reactant.
FT-IR spectra for solid phase products are depicted in Figure 10 based on temperature and mass ratio. The temperature effect on the intensity of functional groups from biomolecules was remarkable in most of the peaks, and in others, these disappeared. For instance, the intensity of the highest peak between 3340 and 3600 cm −1 at 673.15 K represented alcohols and carboxylic acid groups. This peak was diminishing as temperature increased and it demonstrated the low gasification efficiency at 673.15 K, which was improved as temperature increased. The peak was suppressed at 773.15 K because of the dehydration effect. The same occurred for the peaks at 1600 and 1400 cm −1 , which represented C=O, aromatic and C-H stretching, its degradation was promoted as temperature increased. The weak peaks near 1730 and 1030 cm −1 were observed for 1:6 mass ratio, these peaks were representative of C-O, C=C, C-C-O stretching, indicating an incomplete degradation and thus needed higher temperatures than the used in this work, but these were removed at lower temperature and mass ratio. Most of the characteristic peaks of biomass lost their intensity because reaction temperature enhanced the formation of intermediate compounds whose were subsequently part of the syngas, as observed at 773.15 K. Regarding B:W mass ratio, some peaks appeared at the lowest mass ratio since the probable poor intimate interaction between water and biomass or intermediate chemicals in comparison with a frequent contact between water and other molecules for high diluted feed. Therefore, those components in the absence of water contact tended to precipitate or promote other reactions, such as polymerization. The absence or low intensity of peaks at high-diluted samples and 773.15 K indicated an adequate biomass dissolution and hydrolysis, together with polymerization of intermediate chemicals.

Discussion
Supercritical water gasification of guava biomass was studied in the range of 673.15 to 773.15 K in a batch reactor. Based on the biomass characterization, ash, and moisture content, it would obtain promising results if temperatures were higher than 673.15 K under supercritical water conditions. Besides, the highest degradation would be expected for lignocellulosic material at higher temperatures based in the weight loss observed in TGA analyses.
Gas production was clearly affected by temperature and B:W mass ratio. The highest gasification efficiency (CGE = 36%, HGE = 58%) and hydrogen gas yield (7.7 mol per 1 kg of guava biomass) were reached at 773.15 K and 1:6 B:W mass ratio. Overall findings are promising results to explore higher temperatures aiming high value-added compounds production for energy purposes. Hydrocarbon production was slightly improved at high temperatures since the dominant effect of the other reactions. The highest values corresponded to methane, followed by ethane, propane, and butane. It would be probable that ethylene and propylene could be in gas phase but in trace amounts, compared with the obtained for ethane and propane. On the opposite, chemicals were produced in detriment of carbon dioxide, whose formation diminished as temperature and mass ratio were rising; besides, low carbon monoxide production was observed along all the reactions. The optimal conditions, high temperature, and high mass ratio favored syngas production, and it could be confirmed throughout LHV. Low concentration and high temperature on feed tend to suppress phenolic compounds formation on solid products, based on the high-diluted biomass waste.