Life Cycle Assessment of Dynamic Water Flow Glazing Envelopes: A Case Study with Real Test Facilities

: High initial costs hinder innovative technologies for building envelopes. Life Cycle Assessment (LCA) should consider energy savings to show relevant economic beneﬁts and potential to reduce energy consumption and CO 2 emissions. Life Cycle Cost (LCC) and Life Cycle Energy (LCE) should focus on investment, operation, maintenance, dismantling, disposal, and/or recycling for the building. This study compares the LCC and LCE analysis of Water Flow Glazing (WFG) envelopes with traditional double and triple glazing facades. The assessment considers initial, operational, and disposal costs and energy consumption as well as different energy systems for heating and cooling. Real prototypes have been built in two different locations to record real-world data of yearly operational energy. WFG systems consistently showed a higher initial investment than traditional glazing. The ﬁnal Life Cycle Cost analysis demonstrates that WFG systems are better over the operation phase only when it is compared with a traditional double-glazing. However, a Life Cycle Energy assessment over 50 years concluded that energy savings between 36% and 66% and CO 2 emissions reduction between 30% and 70% could be achieved.


Introduction
In recent years, clean energy use has steadily grown. However, energy consumption has not altered its pattern, with fossil fuels acting as the primary energy consumption and generation source. Many carbon emissions and greenhouse gasses caused by conventional energy sources have severe consequences on the environment. Therefore, building codes, regulations, and energy directives consider carbon emissions' impact when evaluating energy efficiency [1]. New technologies emerge rapidly and force building designers to act without a thorough environmental impact analysis [2]. To control the construction sector's environmental impact is the most critical challenge that the architecture, engineering, and construction (AEC) industry must face soon [3,4]. Life Cycle Assessment (LCA) is a comprehensive and internationally standardized method. It quantifies all relevant emissions, resources consumed, and the related environmental aspects associated with any goods or services [5,6].

Literature Review
Extensive investigation has been conducted to study the environmental impact of building materials [7]. A Life Cycle Assessment can significantly help improve a sustainable building design by presenting how different materials or processes contribute to the

Objectives and Innovation
Water Flow Glazing has proven its potential for energy savings and for increasing comfort of occupants in previous studies. The main contribution of this article has been to carry out a thorough analysis of a 50-year life cycle from the energy and cost perspectives. To accomplish this task, the authors have employed a tested methodology used in previous scientific articles. This study considered two prototypes in different locations, glazing compositions and energy systems. Real-world data were collected from these prototypes and analyzed to determine the actual energy performance of WFG systems. This paper is structured into four separate parts. Section 2 of this article provides background information on Water Flow Glazing technology, a description of the WFG test facilities, and finally the methodology of Life Cycle Energy analysis (LCE) and Life Cycle Cost (LCC) calculations. Section 3 provides an analysis of the year-long data collection that occurred at the WFG facilities. This section also contains information pertaining to the embodied energy, the operational energy, and the renewable energy production of the test facilities. Section 4 is a discussion on LCE and LCC and their impact on global warming potential based on a multi-index evaluation. In addition to this, this section has a discussion on the limitations of the methodology. The fifth and final section is the conclusions section.

Materials and Methods
Water flow glazing can be used as both a high-performance envelope as well as an element of the heating and cooling system. The WFG module presented in this paper is made up of three components: an extruded aluminum frame, the glazing, and a circulating device. The glazing is a compound of several layers of laminated glass and coatings, with thermal and spectral properties provided by the glass manufacturers. It combines coatings and Polyvinyl butyral layers with a variable water mass flow rate to absorb or reject incoming infrared solar radiation. The circulating device is defined by a water pump, an exchanger that can regulate heat, and different sensors (such as the water flow and water temperature) to regulate the different fluid variables involved. Finally, the aluminum assembly provides the frame with structure. Although WFG can absorb and transport thermal energy, alternative heating and cooling sources might be added to compensate for the heat losses and gains and maintain comfort conditions. The initial cost of the glazing exceeds the cost of a traditional double or triple glazing panel. However, its performance has to be evaluated over its life cycle to consider potential energy savings. In addition, the water flow captures the solar infrared radiation and increases its temperature through the window. This water is transported and eventually releases the energy in buffer tanks so that thermal energy can be used in hydronic heating systems. The renewable energy integrated into the building envelope might not be enough to meet the energy needs, so it is necessary to study different energy sources and systems to compare their final energy consumption and greenhouse gas emission potential. The Life Cycle Assessment of Water Flow Glazing includes four phases. Phase 1 is the extraction, production of construction materials, and transportation of materials from the extraction point to the construction site. Phase 2 is the construction phase, including required energy to run construction machinery, any additional materials for construction, and any waste disposal. Phase 3 includes the energy required for the building's actual operation (including all energy used during the building occupation over the total lifespan of the structure), general maintenance, repairs, and finally, any required material replacement for the building. Finally, phase 4 involves demolition and transport of waste to recycling plants or landfills.

Water Flow Glazing Thermal Properties
Heat flux through any glazing depends on the difference between the indoor and outdoor temperatures (θ e − θ i ) and the direct and diffuse solar radiation, i 0 . Equation (1) shows the heat flow, q, in glazing panels with gas chambers depending on the thermal transmittance, U, and g-factor. Equation (2) illustrates that the variable fluid's temperature and mass flow rate impact the heat flow through the glazing. Equations (1) and (2) are valid assuming steady conditions, constant values for convective and radiative coefficients, negligible thermal resistance and thermal mass of the glass panes and the water chamber, and the uniform flow inside the water chamber.
where U w is the thermal transmittance between the water chamber and the interior, U is the glazing thermal transmittance, θ e is the outdoor temperature, θ i is the indoor temperature, and θ IN is the inlet temperature of the fluid into the WFG system. Equations (3)-(5) are taken from a previous article [38]. They show the thermal transmittances of WFG, along with the g-factor. All the parameters depend on the mass flow rate, which is estimated uniform inside the glass pane.
Water flow glazing can change the thermal performance by varying the mass flow rate per unit of surface,ṁ. U and U w are two additional thermal transmittances that depend on the mass flow rate. The productṁc denotes the potential of the water to transfer energy. U i and U e thermal transmittances were obtained utilizing the convective heat coefficients, h e , h i , h g , h w . The thermal resistance, (1/U e ) is the sum of the thermal resistances from the water chamber to the outdoors. Similarly, the thermal resistance, (1/U i ), is the sum of the thermal resistances from the water chamber to indoors. Hence, U e represents the thermal transmittance between the water chamber and outdoors, and U i , the thermal transmittance between that water chamber and indoors. A w is the water absorptance, whereas A 1 , A 2 , A 3 are the glass panes absorptances.
This study included two separate prototypes. The first one was placed in Peralveche, Spain (latitude 40 • 36 42" N, longitude 2 • 26 57" W, altitude 1111 MAMSL). The second one was built and tested in Sofia, Bulgaria (42 • 39 1" N, 23 • 23 26" E, Elevation: 590 m a.s.l.). The Peralveche WFG cabin was made of double glazing with a water chamber. Figure 1 shows the WFG cabin and energy system schematics. The glass panes utilized to build this glazing assembly were Planiclear 6 + 6 mm with Poly-Vinyl Butyral layers (1 × 0.38 mm), a water chamber measuring 16 mm, and Planiclear 8 + 8 mm with Poly-Vinyl Butyral layers (1 × 0.38 mm). The cabin had six sides and each side was a square of 2 m × 2 m. The WFG panels were connected to four borehole heat exchangers buried 50 m underneath the cabin. The WFG cabin managed two different closed loop circulating systems. The first loop consisted of pipes that distributed refrigerant fluid from the borehole heat exchangers to the circulation pump. The WFG cabin in- The glass panes utilized to build this glazing assembly were Planiclear 6 + 6 mm with Poly-Vinyl Butyral layers (1 × 0.38 mm), a water chamber measuring 16 mm, and Planiclear 8 + 8 mm with Poly-Vinyl Butyral layers (1 × 0.38 mm). The cabin had six sides and each side was a square of 2 m × 2 m. The WFG panels were connected to four borehole heat exchangers buried 50 m underneath the cabin. The WFG cabin managed two different closed loop circulating systems. The first loop consisted of pipes that distributed refrigerant fluid from the borehole heat exchangers to the circulation pump. The WFG cabin included a second loop that circulated water through vertical facades and the horizontal roof and the mass flow rate was set to 0.9 L·min −1 ·m −2 . Table 1 shows the glazing's thermal and spectral values from previous articles [38,39]. This WFG cabin was compared with another, referred to as Reference prototype, which had double glazing with an air cavity.

Orientation
Area (m 2 ) As per the Sofia prototype, the square plan dimensions were 7 m × 7 m. The walls are parallelograms of 7 m by 3.4 m comprised of five WFG modules facing east, west, and south, respectively. Figure 2 shows the unitized facade module. The circulating system incorporated a solar water pump and a plate heat exchanger connected to the water distribution pipes. The unitized WFG panels measured 3000 mm high and 1300 mm width, and the mass flow rate was set at 2 L·min −1 ·m −2 . In the Southern glazing, the following layers were employed: a single 10 mm diamant glass pane, a 16 mm argon chamber, a low-emissivity coating Planitherm XN, Planiclear (8 mm), 2 Saflex R solar (SG41), Planiclear (8 mm), water chamber (24 mm), Planiclear (8 mm), 4 Saflex R standard clear (RB11), Planiclear (8 mm). Eastern and western glazing composition was meant to reject energy, so a highly reflective coating was included, instead of the low emissivity coating.  Table 2 shows the thermal properties of the glazing taken from a previous article [40]. The total glass area was 60 m 2 . This WFG cabin was compared with another one, referred to as Reference prototype, with triple glazing with an air cavity and an argon cavity. The glass layers and coatings were the same as the WFG.   Table 2 shows the thermal properties of the glazing taken from a previous article [40]. The total glass area was 60 m 2 . This WFG cabin was compared with another one, referred to as Reference prototype, with triple glazing with an air cavity and an argon cavity. The glass layers and coatings were the same as the WFG. Table 2. Thermal properties of Sofia glazing.

Life Cycle Energy (LCE) Analysis
The total embodied energy of building elements involves the energy consumed directly at the primary material extraction, manufacturing, and assembly. These amounts of energy constitute the element's initial embodied energy, and the operational energy includes the heating and cooling energy consumption. Primary energy also considers the energy required to produce the final energy consumed in the building, and it varies according to fuel type and transportation losses. Primary energy is proportional to energy-related CO 2 emissions [41,42]. Life Cycle Energy comprises the building's operational energy, initial and recurrent embodied energy over its lifetime, and, finally, the energy for demolition and disposal. Equation (6) was used to calculate the Life Cycle Energy.
where E is the total energy of the building element, E i is the initial embodied energy, E err is the recurrent embodied energy for future maintenance and refurbishment (5% of the initial embodied energy), E o is the total annual operational energy, n is the lifetime of the element in years, and E d is the embodied energy required for demolition and disposal (3% of the initial embodied energy). Some LCE analysis studies include energy requirements such as lighting, cooking, hot water, and appliances. However, this study includes only the heating and cooling energy through the envelope. For the purposes of this paper, the energy absorbed by the WFG panels was considered as renewable energy production over the operational time in the final energy balance. Therefore, when calculating the total annual operational energy variable, this will be determined by taking the total energy consumption value and subtracting the amount of energy provided by the WFG panels in the structure.

Life Cycle Cost (LCC) Analysis
In addition to improving the thermal performance and reducing the environmental impact, the design of an efficient building envelope needs to pay attention to reducing the economic costs. Building owners demand the selection of cost-effective elements of the building envelope in a sustainable building design. Therefore, in terms of effective decision-making, it is essential to have a complete insight into the construction and running costs throughout the building's lifespan. The Life Cycle Cost (LCC) approach is based on optimizing design solutions and minimizing the sum of construction and operating expenses over the building lifetime. The building envelope's Life Cycle Cost has included its construction cost, C 1 , operation cost, C 2 , and demolition cost, C 3 . The present value interest factor of the annuity (PVIFA) was used to calculate the operation cost's current value. The present value interest factor (PVIF) was used to estimate the demolition and disposal cost's current value at the end of the envelope life cycle. C represents the building envelope's total Life Cycle Cost and the heating and cooling system; r represents the interest rate; n represents the design operating life in years. Therefore, the proposed Life Cycle Cost model for building facades is presented in Equation (7).

Results
This section started by defining the parameters to quantify the environmental performance: primary energy, equivalent CO 2 emissions, and cost. The building reference time was defined as 50 years.
Depending on the local context, the embodied impact may surpass the operational impact. The indicators that measure energy performance can be split into economic factors and physical energy factors.

Embodied Energy Calculation
The building elements' embodied energy has been taken from different sources, whereas the operational energy was calculated with experimental data from the prototypes. It was assumed that the structures were not renovated during this time and had no change in their usage mode throughout their useable life. Energy use, in the viewpoint of the various stages of a building's life cycle, in cold-weather temperatures, the operational stage can reach upwards of 80%. In contrast, the building materials and in-situ construction account for 10-20% [43]. For simplification purposes, the energy for demolition and disposal is a percentage of the total primary energy. Embedded Energy (EE) is the total energy needed to produce goods and services, including processing, mining and extraction, manufacturing, and transport of products. Table 3 shows the emissions associated with the EE are the result of energy and emissions quantification based on the ITeC database [18]. The following assumptions have been considered: The embodied energy associated with the replacement, refurbishment, and substitution of materials and products is assumed to be 5% every ten years [44]. The embodied energy associated with demolition and disposal was assumed to be 3% of the total building Life Cycle Energy [45][46][47]. The considered energy for replacement, demolition, and transportation to landfill does not exceed 10 kWh.m −2 . The energy systems used for this study were borehole heat exchangers coupled with a ground-source heat pump for the WFG Peralveche prototype, Air-to-Water heat pump for WFG Sofia prototype, and Air-to-Air heat pump for both reference prototypes. All the heat pumps are considered to be 7 to 20 kW. The chosen system boundaries include the production of the component, starting from raw materials, the use stage, and the dismantling stage of both systems, along a temporal horizon of 50 years. Closed-loop borehole heat exchangers were made of high-density polyethylene vertical pipes with water (78%) and ethylene glycol (22%) mixture flowing. The installation process included drilling boreholes and trenches, inserting a vertical loop, and grouting operations of the borehole with concrete and bentonite mixture [48][49][50]. The dismantling process included the disposal of the glycol, the sealing of the borehole, and the disposal at the heat pump's end of life. Table 4 shows the embodied energy, emissions, and cost associated with the energy systems used to operate the different prototypes. The compressor and structure were made of reinforced steel and the evaporator and condenser from low alloyed steel. The pipes, cables, and expansion valves were made of copper. Pipes were insulated with a polymer and the cables were insulated with PVC. The refrigerant was assumed to be the same (tetrafluoroethane) for all the heat pumps. The heat pumps were considered maintenance-free, and their lifetime, 25 years.

Renewable Energy Production
Renewable primary energy (RPE in kWh·m −2 ) was produced as the water flowed through the glazing. The data were measured over a year. The RPE can cover part of the winter's heating needs and was subtracted from the non-renewable primary energy needed to maintain the prototype's indoor temperature within a comfort range. The heat absorption rate in the southern facades is closely related to the glazing composition and the orientation. When the solar radiation hits in the glazing units, the water chamber absorbs part of that energy. Heating was assumed to be delivered by a hydronic system using the energy absorbed by the WFG envelope. When needed, a heat pump operated to deliver the energy to keep comfort indoor conditions. Figure 3 shows the water heat gain of the prototypes' envelope. The horizontal panels in Peralveche show the largest water heat gain in July with 81.44 kWh·m −2 . When it comes to the southern facades, the Sofia prototype shows the largest heat gain. The mass flow rate was set higher than any other prototypes (2 L·min −1 ·m −2 ), and the southern glazing properties demonstrate the highest absorptance. The peak solar heat gain in the Sofia prototype was 97.39 kWh·m −2 in July.
Energies 2021, 14, x FOR PEER REVIEW 9 of 18 the orientation. When the solar radiation hits in the glazing units, the water chamber absorbs part of that energy. Heating was assumed to be delivered by a hydronic system using the energy absorbed by the WFG envelope. When needed, a heat pump operated to deliver the energy to keep comfort indoor conditions. Figure 3 shows the water heat gain of the prototypes' envelope. The horizontal panels in Peralveche show the largest water heat gain in July with 81.44 kWh.m −2 . When it comes to the southern facades, the Sofia prototype shows the largest heat gain. The mass flow rate was set higher than any other prototypes (2 L.min −1 .m −2 ), and the southern glazing properties demonstrate the highest absorptance. The peak solar heat gain in the Sofia prototype was 97.39 kWh.m −2 in July.

Operational Energy
Heating and cooling energy loads (in kWh.m −2 ) were calculated by using Equation (1) for the reference glazing and Equation (2) for WFG. The inputs were measured over a year time. Real data, obtained from the prototype throughout the year, allowed the correlation between the WFG cabin and the Reference cabin. Figure 4 shows the heating and cooling

Operational Energy
Heating and cooling energy loads (in kWh·m −2 ) were calculated by using Equation (1) for the reference glazing and Equation (2) for WFG. The inputs were measured over a year time. Real data, obtained from the prototype throughout the year, allowed the correlation between the WFG cabin and the Reference cabin. Figure 4 shows the heating and cooling energy in kWh·m −2 to keep the inside within comfort temperature over the year. The figure considers only the energy that goes through the transparent envelope. The cooling load of the Peralveche Reference cabin showed by far the highest energy consumption with a peak of 118 kWh·m −2 in July.

Operational Energy
Heating and cooling energy loads (in kWh.m −2 ) were calculated by using Equation (1) for the reference glazing and Equation (2) for WFG. The inputs were measured over a year time. Real data, obtained from the prototype throughout the year, allowed the correlation between the WFG cabin and the Reference cabin. Figure 4 shows the heating and cooling energy in kWh.m −2 to keep the inside within comfort temperature over the year. The figure considers only the energy that goes through the transparent envelope. The cooling load of the Peralveche Reference cabin showed by far the highest energy consumption with a peak of 118 kWh.m −2 in July.   Table 5 shows conversion factors between non-renewable primary energy, NRPE, and final energy, FE (kWh NRPE /kWh FE ), as well as CO 2 emissions conversion factors provided by the Spanish Regulation of Thermal Installations in Buildings [42]. The price per kWh of different energy carriers or fuels was taken from Eurostat documents [43]. The non-renewable primary energy consumption of the existing building per unit of envelope area and year, NRPEC, in kWh·m −2 per year, was calculated using Equation (8).
The equivalent CO 2 emissions of the existing building per unit of envelope area and year, in kgCO 2 .m −2 per year, were calculated with Equation (9).
Tables 6 and 7 illustrate the non-renewable primary energy consumption (NRPE) with different energy generators in Peralveche and Sofia, respectively. The conversion factor between final energy and non-renewable primary energy (kWh NRPE/kWh FE) and the factor of emitted CO 2 for electricity were taken from Table 3 for mainland electricity: 1.954 for the conversion factor between final energy and non-renewable primary energy (kWh NRPE/kWh FE) and 0.331 for CO 2 emissions for electricity. In the final energy balance, the renewable energy production was subtracted from the WFG prototype heating loads. The ground-source heat pumps' performance depends on the source inlet temperature in the heat pump, and the inlet temperature in the WFG (θ IN ). A typical value of source inlet temperature ranges from 20 • C in ground-source heat pumps (GSHP) to 35 • C in other Water-to-Water (W-W) heat pumps. The parameters that influence Air-to-Air (A-A) heat pumps' performance are the dry bulb exterior air temperature and the dry bulb interior return air temperature [51]. Table 6. Peralveche prototype. Final energy, non-renewable primary energy, and CO 2 emissions.

Peralveche WFG(W-W) RC(A-A) WFG(W-W) RC(A-A)
Energy (   The yearly operating energy was assumed to remain steady during the entire building operation. The resource mix supplying electricity to the buildings is assumed to be unvarying. The HVAC systems' efficiency and the operation schedule were assumed to remain unchanged during the Life Cycle Assessment.

Discussion
WFG can be a part of hydronic heating and cooling systems, and it is compatible with ground-source heat pumps and boilers. In this study, the authors have considered only mainland electricity as the energy source, ground source heat pumps for the Peralveche WFG prototype, Air-to-Water heat pumps for the Sofia WFG prototype, and Air-to-Air heat pumps for the reference prototypes.

Life Cycle Cost Evaluation
The method to evaluate the Life Cycle Cost (LCC) has been shown in Section 2. The parameters to calculate the envelope's Life Cycle Cost and the energy system initial cost have been discussed in Section 3. The operation cost was calculated with data provided by Table 5 and energy prices for mainland electricity. Maintenance costs for the envelope over 50 years have been calculated as a percentage of the initial cost (1% for the reference glass and 5% for WFG), whereas the heat pump's lifetime was 25 years. The cost of the studied WFG unitized facade was 985 €·m −2 , whereas the price for the circulating water pump was 20 €·m −2 . Replacing the water pumps after a 10-year cycle is included in the maintenance cost. Finally, the demolition and disposal costs were calculated as a percentage of the initial cost (3%). Therefore, the total proposed Life Cycle Cost for the building envelope and energy system was calculated according to Equation (7). The total construction costs of the envelopes and the energy systems were calculated by multiplying each envelope component's quantity by the total unit price. The operation cost was converted to the present value based on annual heating and cooling loads through the envelope. The considered demolition and disposal values were 3% of the total construction costs and converted to the present value. This article considered a discount rate of 2% calculated as an average of the harmonized consumer price index in Spain over the last 20 years. The price of energy was taken from Eurostat reports [43]. The material prices of other components come from the ITeC database [18]. Table 8 shows the cost analysis parameters for all cases. Water flow glazing envelopes showed a higher Coefficient C 1 . The initial cost reflected the investment in borehole heat exchangers and circulating devices. However, the coefficient C 2 reflected that the reference yearly operation cost is twice as much as the WFG cost in Peralveche and 1.5 more in Sofia. The total cost considered a 50-year life cycle by converting the operation and disposal costs to the present value. In Peralveche, the reference prototype cost surpassed the WFG one. In Sofia, the WFG is slightly higher than the reference one.

Life Cycle Energy Evaluation
Life Cycle Energy included the materials initial embodied energy, the operational energy for heating and cooling over 50 years, the recurrent embodied energy over its lifetime, and, finally, the energy for demolition and disposal. Equation (6) was used to calculate the Life Cycle Energy. Table 9 shows the initial embodied energy E i , the recurrent embodied energy for future maintenance E err , calculated as a percentage of the initial embodied energy, the total annual operational energy, and the embodied energy required for demolition and disposal E d . The most considerable initial embodied energy Ei was shown in both WFG prototypes. It was more significant in the Peralveche prototype than in Sofia because of the high embodied energy in the borehole heat exchangers. However, the lower operational energy over 50 years compensated for the higher initial energy consumption. Table 10 illustrates the CO 2 emissions, which is the parameter used to assess the global warming potential (GWP) in kgCO 2eq . The life cycle emissions included the same phases: manufacture and transport of construction materials, maintenance, operation of the building, and waste disposal. Improving the thermal performance of the building envelope with WFG caused an increase in the initial cost. However, the amount of energy and CO 2 emissions declined in both cases over the considered life cycle.

Multi-Index Evaluation Model
Usually, the optimum building envelope's thermal performance is often accompanied by an increase in the cost and environmental load. This study established a multi-index evaluation model, including non-renewable primary energy consumption NRPE, global warming potential GWP, and cost, as indicators of the environment's aspects to evaluate a building envelope. Figure 5 shows that the initial cost of the WFG prototype in Peralveche doubled the reference one's cost because of the investment in borehole heat exchangers. Over a 50-year lifetime cycle, the reference prototype's accumulative cost surpasses the WFG prototype, due to the operational cost difference. When it comes to the Life Cycle Energy and the global warming potential the WFG showed a better performance. The reference prototype consumed three times as much energy as the WFG. The accumulative CO 2 emissions for the WFG envelope were 25,247 kgCO 2eq , whereas the reference glass envelope was responsible for 85,286 kgCO 2eq . When the cost is increased by 100%, the total Life Cycle Energy decreased by 1145 GJ. It has been estimated that the initial investment for the WFG system would cost €17,529, while the Reference system would require an initial investment of €7373. The WFG system would require €640.88 for maintenance per year, with an end-of-product, total demolition, and removal cost of €7921. Summing together these values and the initial investment for the system, the final total Life Cycle Cost of the Peralveche WFG system is €40,611. Meanwhile, for Peralveche RC, this system would cost €1239 in maintenance costs per year, with an end-of-product, total demolition, and removal cost of €3921. Combining these values with the initial investment cost shows that the final total Life Cycle Cost of the Peralveche RC system would be €47,767. Therefore, in the Peralveche case, it is apparent that the successful construction and implementation of the WFG system would save the owner a total of €7156 over the total building life cycle period. When it comes to Life Cycle Energy assessment and global warming potential, the WFG system in the Peralveche prototype used 571 GJ of energy during its lifetime. It was also determined that the system would contain 25,452 kgCO 2eq during its 50 years of use. Meanwhile, for the Peralveche RC prototype, the system was calculated to use 1716 GJ of energy, while containing 85,286 kgCO 2eq during its 50 years of use. Therefore, the Peralveche WFG system, when compared to the RC, will save 1145 GJ of energy as well as 59,834 kgCO 2eq of Embodied Carbon over its entire lifetime. Figure 6 shows that the HVAC operation cost over 50 years did not compensate for the higher initial cost of the WFG prototype. Over a 50-year lifetime cycle, the WFG envelope showed a better performance in the Life Cycle Energy and the global warming potential. The accumulative Life Cycle Energy for the WFG envelope was 2377 GJ, whereas the Life Cycle Energy of the reference glass was 3608 GJ. A model integrating Life Cycle Cost with Life Cycle Energy is used to assess the envelope schemes and select the optimal one in the decision-making process. The Sofia WFG system is estimated to initially cost €65,626, while the Sofia Reference system would cost €40,795.  For Sofia prototypes, the WFG system would require €1320 for maintenance per year, with an end-of-product, total demolition, and removal cost of €10,046. Summing together these values, as well as the initial investment for the system, it can be seen that the final total Life Cycle Cost of the Sofia WFG system is €110,865. Meanwhile, for Sofia RC, this system would cost €1923 in maintenance costs per year, with an end-of-product, total demolition and removal cost of €4923. Combining these values with the initial investment cost, the final total Life Cycle Cost of the Sofia RC system would be €103,066. The Sofia WFG system would cost an additional €33,184 compared to Sofia RC over the structure's lifespan.
The WFG system in the Sofia prototype used 2377 GJ of energy, so the system would contain 136,250 kgCO2eq during its 50 years of use. Meanwhile, for the Sofia RC prototype, the system used 3608 GJ of energy while containing 197,625 kgCO2eq during its 50 years of service. In this case, the WFG system will save 1231 GJ of energy while also containing 6137 kgCO2eq less of Embodied Carbon over its entire lifetime as compared to the Reference system.

Conclusions and Limitations
This paper aimed to develop a conceptual framework to assess the building envelope energy consumption throughout their entire life cycle. By analyzing two case studies, the results can assist building designers during the decision-making process at early stages and consider water flow glazing as an option to reduce energy consumption and CO2 emissions.  For Sofia prototypes, the WFG system would require €1320 for maintenance per year, with an end-of-product, total demolition, and removal cost of €10,046. Summing together these values, as well as the initial investment for the system, it can be seen that the final total Life Cycle Cost of the Sofia WFG system is €110,865. Meanwhile, for Sofia RC, this system would cost €1923 in maintenance costs per year, with an end-of-product, total demolition and removal cost of €4923. Combining these values with the initial investment cost, the final total Life Cycle Cost of the Sofia RC system would be €103,066. The Sofia WFG system would cost an additional €33,184 compared to Sofia RC over the structure's lifespan.
The WFG system in the Sofia prototype used 2377 GJ of energy, so the system would contain 136,250 kgCO2eq during its 50 years of use. Meanwhile, for the Sofia RC prototype, the system used 3608 GJ of energy while containing 197,625 kgCO2eq during its 50 years of service. In this case, the WFG system will save 1231 GJ of energy while also containing 6137 kgCO2eq less of Embodied Carbon over its entire lifetime as compared to the Reference system.

Conclusions and Limitations
This paper aimed to develop a conceptual framework to assess the building envelope energy consumption throughout their entire life cycle. By analyzing two case studies, the results can assist building designers during the decision-making process at early stages and consider water flow glazing as an option to reduce energy consumption and CO2 emissions. For Sofia prototypes, the WFG system would require €1320 for maintenance per year, with an end-of-product, total demolition, and removal cost of €10,046. Summing together these values, as well as the initial investment for the system, it can be seen that the final total Life Cycle Cost of the Sofia WFG system is €110,865. Meanwhile, for Sofia RC, this system would cost €1923 in maintenance costs per year, with an end-of-product, total demolition and removal cost of €4923. Combining these values with the initial investment cost, the final total Life Cycle Cost of the Sofia RC system would be €103,066. The Sofia WFG system would cost an additional €33,184 compared to Sofia RC over the structure's lifespan.
The WFG system in the Sofia prototype used 2377 GJ of energy, so the system would contain 136,250 kgCO 2eq during its 50 years of use. Meanwhile, for the Sofia RC prototype, the system used 3608 GJ of energy while containing 197,625 kgCO 2eq during its 50 years of service. In this case, the WFG system will save 1231 GJ of energy while also containing 6137 kgCO 2eq less of Embodied Carbon over its entire lifetime as compared to the Reference system.

Conclusions and Limitations
This paper aimed to develop a conceptual framework to assess the building envelope energy consumption throughout their entire life cycle. By analyzing two case studies, the results can assist building designers during the decision-making process at early stages and consider water flow glazing as an option to reduce energy consumption and CO 2 emissions.
As has been demonstrated, WFG glazing technology typically retains a higher price point for initial construction than the reference prototypes, requiring a substantial investment early on. This is because of the additional equipment needed for the successful operation of WFG panels. The Peralveche reference prototype's initial cost is 42% of the Peralveche WFG cost, whereas the Sofia reference prototype initial cost is 62% of the WFG initial cost. The steeper initial investment for WFG technology can serve as a deterrent for the technology in the eyes of building design professionals. However, when the total Life Cycle Costs of the WFG and RC are also taken into account, WFG can potentially be a much more economical option.
It is not until we consider each system's overall Life Cycle Costs that the economic benefits of WFG systems become apparent. For this study, the building lifespan was determined to be 50 years. The total Life Cycle Cost (LCC) of the Peralveche WFG is 85% of the total Reference system LCC. Meanwhile, the Sofia Reference LCC is 92% of the total WFG LCC. The conclusion derived from these findings is that selecting high-performance triple glazing is better than a WFG in Life Cycle Cost. A WFG system is better over the operation phase only when it is compared with a traditional double-glazing system, as has been demonstrated in Peralveche.
Another important factor that should be taken into account in the analysis between a much more traditional glazing system versus a WFG system is the Life Cycle Energy (LCE) and global warming potential (GWP) variables. The Peralveche WFG system, as compared to the Peralveche reference prototype, has demonstrated a savings of 66% in LCE with a 70% reduction of CO 2 emission. In Sofia, there are similar results. Sofia WFG demonstrated a 36% savings in LCE with a 30% reduction in CO 2 emissions. This analysis shows that a high-performance triple glazing system improves the Reference prototype performance, but WFG performs better in LCE and GWP in both cases.
The WFG system, however, does have several limitations. Firstly, there is an apparent lack of interoperability with the rest of the building systems present in modern structures, especially concerning the ventilation system. In addition to this, it is not always possible to retrieve all the detailed information needed as input for Water Flow Glazing operation. The maintenance of the building systems operation and the control of the building's indoor environmental conditions according to its user's comfort is of the utmost importance, and smart meters can assist in this. However, these devices pose considerable limitations concerning the quality, frequency, and accuracy of data. Therefore, taking these limitations into account, several future steps of research should be undertaken. Firstly, a development of a testing method to evaluate the performance of the unitized module components should be explored. In addition to this, more case studies in several different climate regions should be analyzed. Thirdly, the development of a management system to control the water pump in the circulating device should be realized. The life cycle of the water pump, which is another point of future research, depends on the operating hours and the on-off cycle. Finally, an integration of a whole evaluation protocol, including maintenance, environmental, and economic aspects, should be explored. This could be used by stakeholders involved in the design, maintenance, and monitoring process in future, potential projects.
After monitoring the WFG systems for a year, several uncertainties, misfunctions, and system issues must be addressed. WFG systems are limited by a high initial investment cost coupled with the need for an energy management system integrated with the other required equipment, especially if the system is coupled with borehole heat exchangers combined with a ground source heat pump. The heating and cooling devices must be adequately dimensioned to avoid misfunctions, especially the Air-to-Water heat pump. Further research must include monitoring energy performance much more accurately by attaching sensors to monitor the amount of electricity powering the heat pump to compare the actual thermal and electricity consumption. In addition to this, further standardization of the manufacturing and deployment process is required to bring down upfront investment costs and payback periods. Finally, another potential further research component would be to control indoor relative humidity, which would be achieved by integrating WFG with efficient ventilation systems.

Conflicts of Interest:
The authors declare that they have no conflict of interest. Exterior thermal transmittance (W·m −2 ·K −1 ). U w Thermal transmittance (water chamber-interior) (K).