Researching on the Deterministic Channel Models for Urban Microcells Considering Diffraction Effects

Deterministic channel models, such as the three-dimensional (3D) ray launching method, can yield wireless channel parameters. In the non-line-of-sight (NLOS) propagation, the outdoor 3D ray launching method that considers diffraction effects is more accurate than the one that does not. While considering the diffraction effect, obtaining the diffraction point is challenging. This paper proposed a method for determining diffracted rays using the receiving sphere method in 3D ray launching. The diffraction point is determined using the shortest distance method between two straight lines, and the signal loss from the transmitting to receiving antennas is obtained. Furthermore, experiments on a millimeter wave in a microcell scenario were performed. The test results of the wireless channel parameters were compared with theoretical calculations. The results obtained via the 3D ray launching method that only considers the specular reflection and direct rays agree with the experimental results in the line-of-sight (LOS); furthermore, they generate larger errors compared with the experimental results in the NLOS. The results obtained via the 3D ray launching method that considers the direct ray, reflected rays, and diffracted rays agree with the experimental results both in the LOS and NLOS. Therefore, the 3D ray launching method that considers the diffraction effect can improve the prediction accuracy of the millimeter wave channel parameters in a microcell.


Introduction
Compared with fifth-generation wireless systems (5G) sub-6GHz, millimeter wave technology has unique advantages, such as a large bandwidth, low delay, and high speed, and can effectively meet the needs of future wireless communication systems with respect to capacity and transmission rate [1][2][3]. Therefore, millimeter wave technology has become a core element of 5G.
With the rapid development of wireless mobile communication, the size of a cell is becoming smaller, and the design of a mobile system requires information on transmission at specific sites [4,5]. It is essential for a radio wave propagation model to realize a wireless system. In the past few decades, statistical and deterministic channel models have been proposed in urban microcell environments. Compared with a statistical channel model, a deterministic channel model can solve specific, real-life scenarios. Considering the future communication system design, the outdoor environment will be one of the important application scenarios in wireless communications [6], and its actual environment is complex and changeable. It is difficult for general statistical channel models to distinguish these changes, which makes it difficult to obtain an accurate model. At present, the propagation of radio waves is simulated to obtain the precise channel characteristics of a specific scene in combining the antenna pattern and the bandwidth of the system. Hence, the ray-tracing model has tremendous advantages in terms of its prediction accuracy compared with traditional statistical models and can provide adequate information for the design of broadband wireless systems.
With the development of computer technology and algorithms to enhance accuracy, the ray-tracing algorithm has become a highly effective, accurate, and fast method for wireless channel modeling. Simple and easy to implement, it has been extensively used in propagation prediction in specific scenarios.
Ray-tracing methods mainly include the following two methods: (a) the image method and (b) the shooting and bouncing ray method. The image method can determine the effective reflection path between the transmitting and receiving points. However, the amount of calculation increases owing to many reflecting surfaces in a typical urban environment, and therefore, this method may no longer be applicable in a typical urban environment.
Therefore, the ray launching method is extensively used in propagation modeling. The underlying concept of the ray launching method is to track each ray emitted from the source position to determine whether the rays reach the receiving point. The steps involved are as follows: 1.
Preparation work. There are three main parts. First, the environmental data file must be read, including all the vertex coordinates of the building and the outer normal vector of the wall. Second, various electromagnetic parameters must be initialized, such as the height of the transmitting and receiving antennas, frequency, emission power, wavelength, dielectric constant, and conductivity. Third, the influence of different number of rays on the accuracy of the electric field must be tested by subdividing the polyhedron to generate different types of rays. Furthermore, the regular icosahedron is used.

2.
Direct rays must be assessed to determine whether the receiving antenna is within the line of sight (LOS) of the transmitting antenna. 3.
The reflected and diffracted rays must be detected. The rays that enter the receiving ball after one reflection and diffraction must be identified. 4.
The following must be detected: first-order diffraction ray and one diffraction ray followed by a reflected ray.

5.
Multiple reflections for up to fifth order reflection rays must be detected. 6.
Subsequent calculations. The electric field strength and synthesis of each ray based on the ray path must be calculated. Thus, the path loss is obtained at the receiving point. A brief flow diagram of the 3D ray launching method is shown in Figure 1.
A detailed flow chart of the serial algorithm of the 3D ray launching method is shown in Figure 2. The field strength on the direct ray, one order diffraction rays, multi-order reflection rays, the reflection followed by the diffraction rays and the diffraction followed by the reflection rays can be obtained in Figure 2, respectively. The path loss at the receiving point is calculated to obtain the sum of a single-ray power (SP) and the sum of the complex power (PS) [24,25]. Therefore, L SP = 10 log 10 where E i is the electric field of the ith ray in volts, E 0 is the initial field in volts, and λ is the wavelength in meters.
L PS = 20 log 10 where E total = n ∑ i=1 E i is the total field strength in volts. Whether the ray is a direct ray?
Whether the ray is the reflection followed by diffraction?
Whether the ray is one order diffraction ray?
Whether the ray is the diffraction followed from reflection ray?
Whether the ray is the Multi-order reflection ray? A detailed flow chart of the serial algorithm of the 3D ray launching method is shown in Figure 2. The field strength on the direct ray, one order diffraction rays, multi-order reflection rays, the reflection followed by the diffraction rays and the diffraction followed by the reflection rays can be obtained in Figure 2, respectively. The path loss at the receiving point is calculated to obtain the sum of a single-ray power (SP) and the sum of the complex power (PS) [24,25]. Therefore,

Yes
where i E is the electric field of the ith ray in volts, 0 E is the initial field in volts, and λ is the wavelength in meters.

Calculation of the Direct Wave Field
In the LOS, the direct wave-field strength is

Calculation of the Direct Wave Field
In the LOS, the direct wave-field strength is where s is the distance between the transmitting and receiving antenna in meters, and E 0 is the initial field in volts. k is the wave number in m −1 .

Calculation of the Reflected Field
If the light is reflected once or multiple times before reaching the field point, the light is called a reflected ray. The ray is the reflection of electromagnetic waves at the interface of different media. The propagation direction of the reflected rays depends on the laws of reflection. The strength of the reflected field is determined by the Fresnel equation. At the boundary of the medium, the vertical polarization reflection coefficient and the parallel polarization reflection coefficient are defined as [26] where θ is the incident angle in degrees, the relative permittivity is ε r = ε − j60σλ, ε is the permittivity, and σ is the conductivity.
The strength of the reflected field is [27,28] where E 0 is the electric field at a distance of 1 m from the transmitting antenna in volts, R is the Fresnel reflection coefficient, A is the diffusion factor from the reflection point to the field point, s 1 denotes the distance from the transmitting point to the diffraction point in meters, and s 2 denotes the distance from the diffraction point to the receiving point in meters.

Calculation of the Diffracted Field
The diffracted wave is more complicated compared with the direct and reflected waves. An incident ray will produce many diffracted rays. The calculation formula of the diffraction coefficient is as follows [29,30], where e and m are the vertical and parallel polarizations, respectively. Furthermore, β 0 is the angle between the incident ray and the wedge. F(x) is a transition function, which is used to correct Keller's nonuniformity correction and is a variant of the Fresnel integral. R 0 and R n are the reflection coefficient matrices of the 'o' and 'n' planes on both sides of the diffraction edge, respectively, φ 1 is the angle between the incident ray and the 'o' plane in degrees, φ 2 is the angle formed by the diffracted rays and the 'o' plane, n is the wedge factor in degrees, and k is the number of the carrier wave in m −1 .
The diffraction field is [31], where D is the diffraction coefficient, and A is the diffusion factor. A quick and effective method is proposed herein to determine the diffraction point. As shown in Figure 3, the intersection O 1 between any ray l and the wall is assessed. If the intersection is a virtual point, the corresponding diffraction point O on the edge of the wall will be determined based on the method of determining the shortest distance between two straight lines. Assuming that the distance between the transmitting and the diffraction point is d, the diffraction point O is the center of the circle, and the radius ϕd/ √ 3 is used to determine whether the ray has an intersection with the circle. If there is an intersection, the ray is diffracted; otherwise, no diffraction occurs.
nergies 2021, 14, x FOR PEER REVIEW Figure 3. Schematic showing the method used to determine the diffraction point. The red lin resents ray l, the cuboid denotes the barrier, the sphere represents a virtual receiving sphere, the center of the virtual receiving sphere, and O1 is the point where the ray l intersects with t virtual receiver sphere.

Channel Measurement System at 39 GHz
The available bandwidth of the 5G millimeter-wave frequency band is as hi several gigahertz. This increased bandwidth introduces considerable challenges channel measurement equipment. Traditionally, the broadband channel measure methods include direct radio frequency pulse, spread-spectrum sliding correlation frequency-domain sweep measurements. The method of the spread-spectrum s correlation measurement has become the main method of channel measurements o to its advantages of high processing gain and coverage in the millimeter wave band The measurement system used is based on a spread-spectrum sliding corre principle: According to the measurement requirements, the measurement points ca

Channel Measurement System at 39 GHz
The available bandwidth of the 5G millimeter-wave frequency band is as high as several gigahertz. This increased bandwidth introduces considerable challenges to the channel measurement equipment. Traditionally, the broadband channel measurement methods include direct radio frequency pulse, spread-spectrum sliding correlation, and frequency-domain sweep measurements. The method of the spread-spectrum sliding correlation measurement has become the main method of channel measurements owing to its advantages of high processing gain and coverage in the millimeter wave band.
The measurement system used is based on a spread-spectrum sliding correlation principle: where L is denotes as the actual number of samples averaged in windows, y l [n] is the received signal in the time domain at the nth moment, and y * l [n + N] denotes the conjugate of the received signal in the time domain at the (n + N)th moment. The system has the ability to measure multi-antenna broadband channels in the millimeter-wave frequency band. A rubidium atomic clock is calibrated using the global positioning system (GPS) for time synchronization.
According to the measurement requirements, the measurement points can be planned independently for the transmitter and receiver in the long-distance measurement range. The system is equipped with a 3D antenna turntable, which can accurately control the vertical, horizontal, and pitch rotation angles of the antennas. As shown in Figure 4, the transmitter terminal of the system is mainly composed of a rubidium atomic clock, an M8190 arbitrary waveform generator, E8267D vector signal source, and an analog signal source. The rubidium atomic clock provides a reference signal for time, and M8190 generates analog measurement signals. Furthermore, baseband signals are up-converted to radio frequency signals by the E8267D signal source, and the analog signal source provides a local oscillator signal based on certain conditions.

Channel Measurement Procedure
In this study, measurements were conducted in urban microcells. An omnidirectional antenna, which was fixed at a position to set it in a vertically polarized state, was adopted in the transmitting terminal. The receiving terminal used a horn antenna, and a turntable was used to move in the horizontal and vertical directions, respectively. Different measurement areas were selected for LOS and NLOS measurements based on the distribution of buildings. The transmitter position was fixed during the measurement. Moreover, different measurement points were selected as receivers, including 22 points for LOS and 11 points for NLOS. The distribution of the specific measurement points is shown in Figure 6. The red solid line represents the x-and y-axes, and the z-axis is along The receiving terminal is mainly composed of a down-converter M9362A, the signal source N5183A, and the digitizer M9703A. The radio frequency input range of the downconverter M9362A is 10 MHz to 40 GHz. The N5183A provides the local oscillator signal for the down-converter. The frequency range of the intermediate frequency signal output by the N9362A is in the range of 0.01 to 1.5 GHz, and the M9703A digitizer samples the intermediate frequency signal. GPS signals are used to calibrate the rubidium atomic clocks. The system has a very high temporal synchronization accuracy and supports long-distance measurements.
The transmitting antenna is omnidirectional, and the antenna pattern of the transmitting antenna is shown in Figure 5. Moreover, the operating frequency ranges from 26.

Channel Measurement Procedure
In this study, measurements were conducted in urban microcells. A

Channel Measurement Procedure
In this study, measurements were conducted in urban microcells. An omnidirectional antenna, which was fixed at a position to set it in a vertically polarized state, was adopted in the transmitting terminal. The receiving terminal used a horn antenna, and a turntable was used to move in the horizontal and vertical directions, respectively. Different measurement areas were selected for LOS and NLOS measurements based on the distribution of buildings. The transmitter position was fixed during the measurement. Moreover, different measurement points were selected as receivers, including 22 points for LOS and 11 points for NLOS. The distribution of the specific measurement points is shown in Figure 6. The red solid line represents the x-and y-axes, and the z-axis is along the direction of the height of the building. The blue line represents the lawn. In the LOS scenario, the transmitting antenna is an omnidirectional antenna, and its coordinates are Tx1 (22.3, 64.9, 9). The receiving antenna is a horn antenna, and it moves along the yellow line (that is, along the x-axis) every 5 or 10 m; y = 71.3, z = 1.5, and x assumes the following values: 42.   3. The power of the transmitter is 0 dBm, and the bandwidth of the measurement is 1 GHz. The azimuthal angle is collected every 5°. The transmitter antenna is in a vertically polarized state, and the receiving antenna is also in a vertically polarized state. In the NLOS scenario, the transmitting antenna is an omnidirectional antenna, and Tx2 is (2.9, 54.7, 9); the receiving antenna is a horn antenna that moves once every 5 m along the gray lines. The transmitting antenna and receiving antenna are vertically polarized.
The measurement parameters are listed in Table 1. The complex relative dielectric permittivity of the wall is taken as 3 0.005 r i ε = + based on the value provided in the literature [32]. The farther the receiving antenna is from the transmitting antenna, the smaller the influence of the elevation angle. Therefore, the station that is far away from the transmitting antenna only measured an elevation angle of 0° and azimuthal angle of 360°, as shown in Figure 6. In Figure 6, 3D indicates that the elevation and azimuthal angles are measured; 2D indicates the experimental data where the elevation angle is 0° and the azimuthal angle is 360°.
In LOS environments, the transmitting Tx1 was fixed, and the receiving antenna was movable. In the short range, the azimuthal angle of each receiving point was measured at −10°, 0°, 10°, 20°, 30°, and the elevation angle of each receiving point was measured every 5°. For longer distances, the elevation angle of each receiving point was measured at 0° and the azimuthal angle of the receiving point was measured every 5°. In the NLOS environments, the transmitting point, which is referred to as Tx2, was fixed, and the receiving antenna was moved. In the 3D measurements, the receiving point that was close to the transmitting point was measured at azimuthal angles of −10°, 0°, 10°, 20°, and 30°, and at every 5° in the case of the elevation angles. The receiving point that was far from the transmitting point was at −10°, 0°, and 10° in terms of azimuthal angles and every 5° in the case of elevation angles. Finally, the data were collected and processed as shown in Figure 7.  The measurement parameters are listed in Table 1. The complex relative dielectric permittivity of the wall is taken as ε r = 3 + 0.005i based on the value provided in the literature [32]. The farther the receiving antenna is from the transmitting antenna, the smaller the influence of the elevation angle. Therefore, the station that is far away from the transmitting antenna only measured an elevation angle of 0 • and azimuthal angle of 360 • , as shown in Figure 6. In Figure 6, 3D indicates that the elevation and azimuthal angles are measured; 2D indicates the experimental data where the elevation angle is 0 • and the azimuthal angle is 360 • . In LOS environments, the transmitting Tx1 was fixed, and the receiving antenna was movable. In the short range, the azimuthal angle of each receiving point was measured at −10 • , 0 • , 10 • , 20 • , 30 • , and the elevation angle of each receiving point was measured every 5 • . For longer distances, the elevation angle of each receiving point was measured at 0 • and the azimuthal angle of the receiving point was measured every 5 • . In the NLOS environments, the transmitting point, which is referred to as Tx2, was fixed, and the receiving antenna was moved. In the 3D measurements, the receiving point that was close to the transmitting point was measured at azimuthal angles of −10 • , 0 • , 10 • , 20 • , and 30 • , and at every 5 • in the case of the elevation angles. The receiving point that was far from the transmitting point was at −10 • , 0 • , and 10 • in terms of azimuthal angles and every 5 • in the case of elevation angles. Finally, the data were collected and processed as shown in Figure 7.

Path Loss without Consideration of the Diffraction Effect
A specific environment was considered for the design of the algorithm. The study conducted research on a microcell. Thus, the establishment of a reasonable and general model is the premise for the prediction of the radio wave. An urban environment is characterized by the existence of numerous buildings. To simplify the model, the buildings are generally equivalent to a rectangular parallelepiped with smooth and flat surfaces. The flowers, trees, cars, and other factors are generally ignored, and the loss of the space caused by the scattering is not considered. Thus, the propagation environment of radio waves has been established. Radio waves mainly propagate in air and the directed, reflected, and diffracted rays from the walls, corners of the wall or the ground would occur. The measurement area was divided into two areas based on the propagation scenario: LOS and NLOS. In this study, the equilateral triangle was split into different times, that is, there are 40,962, 163,842, 65,362, and 2,621,442 rays when it was split six, seven, eight, and nine times, respectively. The electric fields of the direct wave and the multiple

Path Loss without Consideration of the Diffraction Effect
A specific environment was considered for the design of the algorithm. The study conducted research on a microcell. Thus, the establishment of a reasonable and general model is the premise for the prediction of the radio wave. An urban environment is characterized by the existence of numerous buildings. To simplify the model, the buildings are generally equivalent to a rectangular parallelepiped with smooth and flat surfaces. The flowers, trees, cars, and other factors are generally ignored, and the loss of the space caused by the scattering is not considered. Thus, the propagation environment of radio waves has been established. Radio waves mainly propagate in air and the directed, reflected, and diffracted rays from the walls, corners of the wall or the ground would occur. The measurement area was divided into two areas based on the propagation scenario: LOS and NLOS. In this study, the equilateral triangle was split into different times, that is, there are 40,962, 163,842, 65,362, and 2,621,442 rays when it was split six, seven, eight, and nine times, respectively. The electric fields of the direct wave and the multiple reflection waves (up to five times) were calculated, and the path loss that changed with distance was obtained.
As shown in Figures 8 and 9, the path loss varied with the distance for the different number of rays in the LOS. The term 'meas' denotes measurements. The red line is the experimental data, and the blue and black lines are both theoretical calculations. The blue line is the sum-of-individual-ray-powers (SP) method, and the black line is the power-ofcomplex-sum (PS) method. The direct ray, first order reflection, second order reflection, third order reflection, fourth order reflection and fifth order reflection are considered in the theoretical calculation. The distance from the measured points to the transmitting antenna are used as values of the abscissas. When the receiver is away from the transmitter, the measured path loss increases as a function of distance in Figures 8 and 9. The PS and SP methods have minor differences from the measured data in the different number of rays, as shown in Figures 8 and 9. As listed in Table 2, the root mean square error (RMSE) of the SP method is less than the RMSE of the PS method, thus indicating that the SP method is better than the PS method in the LOS. When the number of rays is 40,962, the RMSE of the SP method is 4.5106, which is less than the corresponding RMSE values in the cases of other ray numbers. This implies that as the number of rays increased, the agreement between the theoretically calculated and the measured data improved. flection, third order reflection, fourth order reflection and fifth order reflection are considered in the theoretical calculation. The distance from the measured points to the transmitting antenna are used as values of the abscissas. When the receiver is away from the transmitter, the measured path loss increases as a function of distance in Figures 8  and 9. The PS and SP methods have minor differences from the measured data in the different number of rays, as shown in Figures 8 and 9. As listed in Table 2, the root mean square error (RMSE) of the SP method is less than the RMSE of the PS method, thus indicating that the SP method is better than the PS method in the LOS. When the number of rays is 40,962, the RMSE of the SP method is 4.5106, which is less than the corresponding RMSE values in the cases of other ray numbers. This implies that as the number of rays increased, the agreement between the theoretically calculated and the measured data improved.   flection, third order reflection, fourth order reflection and fifth order reflection are considered in the theoretical calculation. The distance from the measured points to the transmitting antenna are used as values of the abscissas. When the receiver is away from the transmitter, the measured path loss increases as a function of distance in Figures 8  and 9. The PS and SP methods have minor differences from the measured data in the different number of rays, as shown in Figures 8 and 9. As listed in Table 2, the root mean square error (RMSE) of the SP method is less than the RMSE of the PS method, thus indicating that the SP method is better than the PS method in the LOS. When the number of rays is 40,962, the RMSE of the SP method is 4.5106, which is less than the corresponding RMSE values in the cases of other ray numbers. This implies that as the number of rays increased, the agreement between the theoretically calculated and the measured data improved.    As shown in Figures 10 and 11, the path loss in the measured data increases as the distance between the transmitter and receiver in the NLOS environment increases and as the received power decreases. In theory, up to five orders of reflections are calculated. The theoretical calculation curves shown in Figures 10 and 11 are not continuous because the receiving antenna is in the NLOS environment relative to the transmitting antenna, and multiple reflections do not occur at the discontinuous receiving point. Therefore, this may be the received signal owing to diffraction. If the diffracted rays are not calculated, or if the effect of the diffracted rays is neglected, the received field strength becomes weaker and the path loss increases. It was found that when the rays were equal to 40,962, 163,842, 655,362, and 2,621,442, there were large differences between the theoretical calculation and experimental data, as shown in Figures 10 and 11. This shows that the diffraction has a significant influence on the electric field strength and the path loss in the NLOS environment.
Energies 2021, 14, x FOR PEER REVIEW 12 of 18 As shown in Figures 10 and 11, the path loss in the measured data increases as the distance between the transmitter and receiver in the NLOS environment increases and as the received power decreases. In theory, up to five orders of reflections are calculated. The theoretical calculation curves shown in Figures 10 and 11 are not continuous because the receiving antenna is in the NLOS environment relative to the transmitting antenna, and multiple reflections do not occur at the discontinuous receiving point. Therefore, this may be the received signal owing to diffraction. If the diffracted rays are not calculated, or if the effect of the diffracted rays is neglected, the received field strength becomes weaker and the path loss increases. It was found that when the rays were equal to 40,962, 163,842, 655,362, and 2,621,442, there were large differences between the theoretical calculation and experimental data, as shown in Figures 10 and 11. This shows that the diffraction has a significant influence on the electric field strength and the path loss in the NLOS environment.

Path Loss Considering the Diffraction Effect
According to the inference in Section 4.1, the diffraction phenomenon has a very important influence on the received signal in the microcellular environment. Therefore, the direct ray from the transmitter to the receiver, the specular reflection, over-rooftop diffraction, diffraction from a vertical edge, and the diffraction at the intersection of the wall and the ground are calculated and discussed in this section. The direct ray, As shown in Figures 10 and 11, the path loss in the measured data increases as the distance between the transmitter and receiver in the NLOS environment increases and as the received power decreases. In theory, up to five orders of reflections are calculated. The theoretical calculation curves shown in Figures 10 and 11 are not continuous because the receiving antenna is in the NLOS environment relative to the transmitting antenna, and multiple reflections do not occur at the discontinuous receiving point. Therefore, this may be the received signal owing to diffraction. If the diffracted rays are not calculated, or if the effect of the diffracted rays is neglected, the received field strength becomes weaker and the path loss increases. It was found that when the rays were equal to 40,962, 163,842, 655,362, and 2,621,442, there were large differences between the theoretical calculation and experimental data, as shown in Figures 10 and 11. This shows that the diffraction has a significant influence on the electric field strength and the path loss in the NLOS environment.

Path Loss Considering the Diffraction Effect
According to the inference in Section 4.1, the diffraction phenomenon has a very important influence on the received signal in the microcellular environment. Therefore, the direct ray from the transmitter to the receiver, the specular reflection, over-rooftop diffraction, diffraction from a vertical edge, and the diffraction at the intersection of the wall and the ground are calculated and discussed in this section. The direct ray, first-order diffraction, reflection followed by diffraction, diffraction followed from re-

Path Loss Considering the Diffraction Effect
According to the inference in Section 4.1, the diffraction phenomenon has a very important influence on the received signal in the microcellular environment. Therefore, the direct ray from the transmitter to the receiver, the specular reflection, over-rooftop diffraction, diffraction from a vertical edge, and the diffraction at the intersection of the wall and the ground are calculated and discussed in this section. The direct ray, first-order diffraction, reflection followed by diffraction, diffraction followed from reflection, and (up to five orders of) reflections were considered. The path loss at a certain distance was calculated in the study when the number of emitted rays was different in the LOS environment, as shown in Figures 12 and 13. agreement in general. When the distance between the transmitting and receiving antennas is around 100 m, the SP method and the experimental data have a certain error, which is caused by the obstacles, such as by the surrounding cars, telegraph poles, and vegetation. However, the error is within the allowable range. The measured data are consistent with the theoretical calculations, thus indicating that the results obtained by the algorithm in this study are effective. The theoretical calculations of 40,962 rays are in good agreement with the measured data irrespective of whether diffraction was considered. The RMSE of the SP method was 4.5106 when diffraction was not considered. When diffraction was considered, the RMSE of the SP method was 3.9318. The two values were not very different, thus indicating that the diffraction effect was very weak in the LOS. However, the 3D ray launching method that considers the effect of diffraction can generally predict the electric field intensity of any field point near the communication base station. A 2D visualization of the propagation path from the transmitting (22.3, 64.9, 9) to the receiving (172.3, 71.3, 1.5) location is shown in Figure 14. There are numerous rays from the transmitting point to the receiving point, indicating multipath propagation.    In Figures 12 and 13, the path loss varies as a function of distance between the transmitting and receiving antennas in the LOS environment. As the distance increases, the path loss will increase, and the received power will decrease. When 40,962 and 163,842 rays are used, the calculated results of the PS method do not fit well with the measured data. However, the calculated results of the PS method for 655,362 and 2,621,442 rays are generally in agreement with the measured data. The RMSE of the SP method is smaller than that of the PS method in general ( Table 3). The RMSEs of the SP method with 40,962 rays and 163,842 rays are 3.9318 and 3.9212, respectively. The RMSEs of the SP method with 10,242, 655,362, and 2,621,442 rays are 4.1386, 4.1032, and 3.9704, respectively. Therefore, considering the calculation time and accuracy, the use of 40,962 rays is the best choice. The theoretical calculation and the measured data are in good agreement in general. When the distance between the transmitting and receiving antennas is around 100 m, the SP method and the experimental data have a certain error, which is caused by the obstacles, such as by the surrounding cars, telegraph poles, and vegetation. However, the error is within the allowable range. The measured data are consistent with the theoretical calculations, thus indicating that the results obtained by the algorithm in this study are effective. The theoretical calculations of 40,962 rays are in good agreement with the measured data irrespective of whether diffraction was considered. The RMSE of the SP method was 4.5106 when diffraction was not considered. When diffraction was considered, the RMSE of the SP method was 3.9318. The two values were not very different, thus indicating that the diffraction effect was very weak in the LOS. However, the 3D ray launching method that considers the effect of diffraction can generally predict the electric field intensity of any field point near the communication base station. A 2D visualization of the propagation path from the transmitting (22.3, 64.9, 9) to the receiving (172.3, 71.3, 1.5) location is shown in Figure 14. There are numerous rays from the transmitting point to the receiving point, indicating multipath propagation.    In Figures 15 and 16, the path loss in a certain distance changes with the dis between the transmitting and the receiving antenna in the NLOS environment. It c observed from these figures that when the distance is between 23 and 55 m, the d ence between the theoretical calculation and the measured data is approximately for 40,962, 163,842, and 655,362 rays. However, the difference between the theor calculation and the measured data is approximately 15 dB when the distance is bet 10 and 23 m. This is attributed to the fact that when the diffraction is not consid there are no multiple reflections from the transmitting to the receiving locations tween 10 and 23 m), and the path loss cannot be calculated. When the diffraction is sidered, first-order diffraction, reflection followed by diffraction, and diffraction lowed from reflection would occur from the transmitting to the receiving points. shows that diffraction has a certain effect in the NLOS case. The difference betwee In Figures 15 and 16, the path loss in a certain distance changes with the distance between the transmitting and the receiving antenna in the NLOS environment. It can be observed from these figures that when the distance is between 23 and 55 m, the difference between the theoretical calculation and the measured data is approximately 6 dB for 40,962, 163,842, and 655,362 rays. However, the difference between the theoretical calculation and the measured data is approximately 15 dB when the distance is between 10 and 23 m. This is attributed to the fact that when the diffraction is not considered, there are no multiple reflections from the transmitting to the receiving locations (between 10 and 23 m), and the path loss cannot be calculated. When the diffraction is considered, first-order diffraction, reflection followed by diffraction, and diffraction followed from reflection would occur from the transmitting to the receiving points. This shows that diffraction has a certain effect in the NLOS case. The difference between the SP method and the measured data may be attributed to the fact that the surrounding fitness equipment and vegetation were ignored. The 3D ray launching method was in good agreement with the measured data as the distance varied between 23 and 55 m. The RMSE of the theoretical calculation is the smallest when the number of rays is 655,362, as shown in Table 4; that is, the RMSEs of the PS method are 8.5142 and 7.8922, respectively. This indicates that the theoretical calculation that considers the effect of diffraction is in a better agreement with the measured data compared with the 3D ray launching method that does not consider the effect of diffraction. This confirms the validity of the results obtained by the new ray launching method. A 2D visualization of the propagation path from the transmitting (2.9, 54.7, 9) to the receiving (60, 62.9, 1.5) antenna in the NLOS is shown in Figure 17. The figure shows that the number of rays in the NLOS is not as rich as the ones in the LOS. The 3D ray launching method that considered the effect of diffraction provided a theoretical basis for the urban radio wave transmission and the setting and optimization of the base station location. good agreement with the measured data as the distance varied between 23 and 55 m. The RMSE of the theoretical calculation is the smallest when the number of rays is 655,362, as shown in Table 4; that is, the RMSEs of the PS method are 8.5142 and 7.8922, respectively. This indicates that the theoretical calculation that considers the effect of diffraction is in a better agreement with the measured data compared with the 3D ray launching method that does not consider the effect of diffraction. This confirms the validity of the results obtained by the new ray launching method. A 2D visualization of the propagation path from the transmitting (2.9, 54.7, 9) to the receiving (60, 62.9, 1.5) antenna in the NLOS is shown in Figure 17. The figure shows that the number of rays in the NLOS is not as rich as the ones in the LOS. The 3D ray launching method that considered the effect of diffraction provided a theoretical basis for the urban radio wave transmission and the setting and optimization of the base station location.     Table 4; that is, the RMSEs of the PS method are 8.5142 and 7.8922 respectively. This indicates that the theoretical calculation that considers the effect o diffraction is in a better agreement with the measured data compared with the 3D ra launching method that does not consider the effect of diffraction. This confirms the va lidity of the results obtained by the new ray launching method. A 2D visualization of th propagation path from the transmitting (2.9, 54.7, 9) to the receiving (60, 62.9, 1.5) an tenna in the NLOS is shown in Figure 17. The figure shows that the number of rays i the NLOS is not as rich as the ones in the LOS. The 3D ray launching method that con sidered the effect of diffraction provided a theoretical basis for the urban radio wav transmission and the setting and optimization of the base station location.

Conclusions
To improve the prediction accuracy of the signal in the millimeter wave in typical urban microcells, a channel measurement experiment at 39 GHz was conducted. Herein, a 3D ray launching method that considered the effect of diffraction was studied. The results showed that when diffraction was not considered in the 3D ray launching method in the outdoor microcell, the field strength of the receiving antenna cannot be calculated if the theoretical calculations appeared discontinuous in the NLOS propagation. Moreover, there were major differences between the theoretical calculations and experimental data in the cases of different number of rays in the NLOS propagation. This discrepancy may be caused by the diffraction effect. This means that the diffraction effect has a very important influence on the signal reception in the NLOS propagation. The diffraction effect was then considered in the 3D ray launching method. In the LOS propagation, the results showed that the RMSE of the 3D ray launching method that considered the diffraction effect was almost the same as the RMSE of the 3D ray launching method that did not consider the diffraction effect for 655,362 rays. This showed that the diffraction effect was very weak in the LOS propagation. In the NLOS propagation, the RMSEs of the PS and SP methods for 655,362 rays were 8.5142 and 7.8922, respectively. Moreover, the RMSE values obtained by considering the effect of diffraction were much smaller than those that did not consider the effect of diffraction in the NLOS propagation. The theoretical calculations that considered the effect of diffraction and the measurement data were in good agreement in general. Some deviations between the SP method and the measured data may be attributed to the influence of the surrounding environment. The above analysis showed that the diffraction effect should be considered in the 3D ray launching method in an outdoor microcell. Further studies on radio wave propagation in outdoor microcells will be of great significance for the selection and optimization of base station locations.

Conclusions
To improve the prediction accuracy of the signal in the millimeter wave in typical urban microcells, a channel measurement experiment at 39 GHz was conducted. Herein, a 3D ray launching method that considered the effect of diffraction was studied. The results showed that when diffraction was not considered in the 3D ray launching method in the outdoor microcell, the field strength of the receiving antenna cannot be calculated if the theoretical calculations appeared discontinuous in the NLOS propagation. Moreover, there were major differences between the theoretical calculations and experimental data in the cases of different number of rays in the NLOS propagation. This discrepancy may be caused by the diffraction effect. This means that the diffraction effect has a very important influence on the signal reception in the NLOS propagation. The diffraction effect was then considered in the 3D ray launching method. In the LOS propagation, the results showed that the RMSE of the 3D ray launching method that considered the diffraction effect was almost the same as the RMSE of the 3D ray launching method that did not consider the diffraction effect for 655,362 rays. This showed that the diffraction effect was very weak in the LOS propagation. In the NLOS propagation, the RMSEs of the PS and SP methods for 655,362 rays were 8.5142 and 7.8922, respectively. Moreover, the RMSE values obtained by considering the effect of diffraction were much smaller than those that did not consider the effect of diffraction in the NLOS propagation. The theoretical calculations that considered the effect of diffraction and the measurement data were in good agreement in general. Some deviations between the SP method and the measured data may be attributed to the influence of the surrounding environment. The above analysis showed that the diffraction effect should be considered in the 3D ray launching method in an outdoor microcell. Further studies on radio wave propagation in outdoor microcells will be of great significance for the selection and optimization of base station locations.