Analysis of the Wind Turbine Selection for the Given Wind Conditions

: The aim of the current paper is to present an approach to a wind turbine selection based on an annual wind measurements. The proposed approach led to a choice of an optimal device for the given wind conditions. The research was conducted for two potential wind farm locations, situated on the north of Poland. The wind measurements pointed out a suitability of the considered localizations for a wind farm development. Six types of wind turbines were investigated in each localization. The power of the wind turbines were in the range of 2.0 to 2.5 MW and with a medium size of the rotor being in the range of 82 to 100 m. The purpose of the research was to indicate a wind turbine with the lowest sensitivity to the variation of wind speed and simultaneously being most effective energetically. The Weibull density distribution was used in the analyses for three values of a shape coefﬁcients k . The energy efﬁciency of the considered turbines were also assessed. In terms of the hourly distribution of the particular wind speeds, the most effective wind turbines were those with a nominal power of 2 MW, whereas the least effective were those with the nominal power of 2.3–2.5 MW. The novelty of the proposed approach is to analyze the productivity for many types of wind turbines in order to select the one which is the most effective energy producer. The analyses conducted in the paper allowed to indicate a wind turbine which generates the highest amount of energy independently on the wind speed variation.


Introduction
Optimum usage of energy sources has become the priority for the majority of countries and regions. Considering that many countries have withdrawn from using raw fossil materials, the contribution of renewable energy generation forms will continue to grow stronger [1]. Research shows that the use of fossil fuels to obtain energy results in harmful air emissions, which impact global warming [2,3]. Authors of numerous forecasts state that the use of energy will continue to grow, and in the year 2050 it will reach a 50% higher level than the present one [4]. Production of energy based on fossil fuels will increase, but its growth will be considerably slower than the energy production from renewable sources. Renewable energy sources include wind, solar radiation, biomass, precipitation, marine tides, sea waves and geothermal energy. The most extensively used renewable source of energy is the gravitational energy of water. In 2018 it corresponded to 62.8% of energy from renewable sources. Other sources include wind (19.0%), solar energy (8.8%), biofuels (6.3%) and geothermal energy [5].
In the last two decades, wind energy has faced the greatest growth of resource use. It is also characterized by a rapid return on investment [6]. The popularity of wind energy around the world is linked to the general availability of the energy source, which is wind. The wind energy is generated without harmful emission of pollutants to the atmosphere, therefore it has minor impact on ecosystems [7][8][9]. A potential impact on the avian fauna [10] and excessive noise generation exist [11][12][13][14]. However, the areas occupied by wind farms can still be used for agricultural and other purposes. It is also important that the wind farm can work as a part of a power system as well as working autonomously. The whole investment process lasts for about 2 years and gives the opportunity to select the farm output adapted to the needs and financial resources of the investor.
While choosing the land for wind farm construction it is crucial to find the one with the highest wind potential. The most desirable location is where the annual mean of the wind speed is more than 5 m/s [15,16]. Taken into consideration while deciding on the construction of the future wind farms are: topographic maps, identification of the land roughness and solid barriers, assumptions on wind conditions, selection of the height and power of the wind turbines.
The data below provides the average of the multi-annual (often 60-year) wind speed and demonstrates fluctuations of this speed over a long period of time ( Figure 1). therefore it has minor impact on ecosystems [7][8][9]. A potential impact on the avian fauna [10] and excessive noise generation exist [11][12][13][14]. However, the areas occupied by wind farms can still be used for agricultural and other purposes. It is also important that the wind farm can work as a part of a power system as well as working autonomously. The whole investment process lasts for about 2 years and gives the opportunity to select the farm output adapted to the needs and financial resources of the investor. While choosing the land for wind farm construction it is crucial to find the one with the highest wind potential. The most desirable location is where the annual mean of the wind speed is more than 5 m/s [15,16]. Taken into consideration while deciding on the construction of the future wind farms are: topographic maps, identification of the land roughness and solid barriers, assumptions on wind conditions, selection of the height and power of the wind turbines.
The data below provides the average of the multi-annual (often 60-year) wind speed and demonstrates fluctuations of this speed over a long period of time ( Figure 1). In order to identify an area with the highest wind potential, the wind atlas can be used. It contains the long-term data about the wind characteristics e.g., speed, distribution and direction, that can be used for the further detailed analyses. These data are typically collected from local meteorological stations. Before the site of the future wind farm is chosen, the measurement campaign has to take place [18][19][20]. The measurement campaign consists of the wind study including measurements of wind speed, direction and air pressure, temperature and humidity measured at several heights above the ground, which last at least one year [21]. The most preferable site of these measurements is the height where the future impeller boss of the wind turbine will be situated. Obtaining the maximum energy performance of the future wind farm requires conducting of the reliable measurements of the wind speed in the selected locality. The reliable measurement results are obtained by using approved measurement procedures and certified measuring equipment [18,19]. The document, describing the proper measurement methodology for the purposes of financial analysis required by the bank, is issued by the International Electrotechnical Commission (IEC Switzerland-Geneva). The guidelines for the measurements are included in the IEC 61400-12-1 standard: Wind turbines: Part 21-1: Power performance of the electricity producing wind turbines [22]. Appendix G of the above norm contains guidelines for the correct installation of measurement equipment on a tube or truss-type In order to identify an area with the highest wind potential, the wind atlas can be used. It contains the long-term data about the wind characteristics e.g., speed, distribution and direction, that can be used for the further detailed analyses. These data are typically collected from local meteorological stations. Before the site of the future wind farm is chosen, the measurement campaign has to take place [18][19][20]. The measurement campaign consists of the wind study including measurements of wind speed, direction and air pressure, temperature and humidity measured at several heights above the ground, which last at least one year [21]. The most preferable site of these measurements is the height where the future impeller boss of the wind turbine will be situated. Obtaining the maximum energy performance of the future wind farm requires conducting of the reliable measurements of the wind speed in the selected locality. The reliable measurement results are obtained by using approved measurement procedures and certified measuring equipment [18,19]. The document, describing the proper measurement methodology for the purposes of financial analysis required by the bank, is issued by the International Electrotechnical Commission (IEC Switzerland-Geneva). The guidelines for the measurements are included in the IEC 61400-12-1 standard: Wind turbines: Part 21-1: Power performance of the electricity producing wind turbines [22]. Appendix G of the above norm contains guidelines for the correct installation of measurement equipment on a tube or truss-type meteorological tower. The guidelines included in the IEC 61400-12-1 [22] standard are said to be international practice for wind measurements. Only the measurements performed with a tall measurement tower can be classified as reliable and therefore can be used in the further stages of the project in order to obtain full or partial project financing. The above is measured to the level of the rotor axis. For currently installing wind turbines this level is in the range of 120 to 160 m. Taking into consideration various aspects of the wind measurement procedure has an impact on reducing the risk of error or uncertainty in the subsequent stages of wind turbine's location design [19]. The measurements of the wind resources in the given location take into account the land form, natural and infrastructural barriers, land inclination and other factors affecting the wind. The wind analysis results in a histogram of the wind speed distribution at one meter/second intervals.
In order to increase the productivity of the wind farm it is crucial not only to install the most productive wind turbine but also to gain the precise knowledge about the characteristics of the wind in a particular location. A lot of experiments were carried out in order to analyze the potential of wind energy usage, considering different perspectives like localization and type of the wind turbine [23][24][25][26]. A significant part of scientific research is aimed at finding the optimal location of the wind farm for one type of wind turbine [27,28]. Other experiments are trying to find out the impact of turbines blades' shape [29] and environmental conditions on the productivity of wind farms [30]. The articles of DTU groups [31] present a wide scope of scientific research elaborating not only on case studies but also on the other solutions being commonly used in a field of wind energy.
It is already stated that it is possible to adjust the proper wind turbine for wide variations of wind conditions [32]. It is also known that the highest turbine with the biggest diameter does not have to be the most energetically productive in every kind of localization. This article also aims to adjust the most productive turbine to precise wind conditions. Two different localizations of wind farm were taken into consideration for the proper analysis as well as the six types of turbines, which are most commonly used in Europe, with their power ranging from 2.0 to 2.5 MW. The aim of the research was to find the turbine which is less sensitive to the variation of a wind speed distribution. That is why the density of Weibull's distribution was analyzed for three values of a shape factor k.

Problem Description
The objective of the conducted study was to select the wind turbine allowing obtaining the maximum economic result for the investment based on available annual wind measurements. Two locations for the wind farms were taken into consideration by the study, referred to as farm A and farm B, each with 120 m high wind turbine. Considering the available wind results at heights lower than the designed height of wind towers, the analyses were carried out in variants. The wind speed increases with height [33]. On the bases of the available data, the mean of the wind speed at 120 m height above the ground was calculated. The wind distribution was determined according to the Weibull probability density function [16] for three values of the k shape coefficient. Value of the A scale parameter was calculated on the basis of the mean of the wind speed and the selected k shape coefficient. Turbines with horizontal axis of rotation and nominal power of 2.0, 2.3 or 2.5 MW were selected. Table 1 lists wind turbines selected for the analysis. The choice of the proper equipment is made on the bases of the measurement results and the characteristics of the wind turbine productivity. The device manufacturer demonstrates the relationship between the turbine power output and wind speed. However, data for different air density values are rarely presented. The device characteristics further includes information on the start speed of the turbine, nominal power output and maximum wind speed resulting in device shutdown. The selected turbines have similar starting wind speed of 3.5 m/s. All of them shut down when the wind speed exceeds 25 m/s. The wind speed did not exceed 24 m/s in the selected locations, therefore turbine shutdown did not influence outcomes of the presented analyses. The P we_i for wind speed v i , being the middle of subsequent class ranges, can be estimated based on the characteristics of wind farm performance. Then, the E we_i energy can be calculated, generated by the wind farm for one year in i-th class range [23]: By summing up the component energy from all ranges, the total energy generated for one year by the wind farm will be obtained E we :

Energy Analysis of Selected Wind Turbines
The main parameter that impacts selection of type of the wind turbine is not only the wind power available but also the distribution of the wind speeds in the tested location. These parameters determine the amount of energy generated, and thus income from investment.

Wind Power
The wind power, modelled as a gas, can be expressed with the following formula [23]: The air density for the normal conditions (at temperature t = 273 K and pressure p = 105 Pa) equals ρ = 1.2759 kg/m 3 . In the wind power sector, the assumed temperature is t = 15 • C and the pressure p = 1013 hPa [34] for which the air density equals to ρ = 1.225 kg/m 3 . Assuming the unit flow area A = 1 m 2 , the unit wind power obtained in the i-th speed range P we_i can be expressed using the following formula: Based on Equations (1)-(4), wind power and energy resources can be calculated for the tested location. The annual average wind speed for farm A is v av = 6.61 m/s, for farm B v av = 6.72 m/s. A preliminary assessment of the result shows that every year in the tested locations a stream of wind passes through the surface area of 1 m 2 carrying a maximum energy of 2053 kW/m 2 for farm A and 2169 kW/m 2 for farm B. Despite the fact that in both locations the values of average wind speed are similar, they differ in the distribution of the individual wind speed classes.

Wind Speed Distribution in Selected Locations
The following analysis used the results of the wind measurements performed in future locations for two wind farms in northern Poland. The two future farms are separated by a distance of over 100 km. Accuracy and correctness for the validation and analysis of measurement data are key determinants for the applicability of the given location in terms of its wind potential. The basic objective of the final report from wind measurements is the summary of the period of measurement and presentation of the results in graphic or tabular form. Construction of wind turbines with the tower height of 120 m above the ground was assumed. As a result of the performed measurement campaign, average wind speeds were obtained, listed in Table 2.  Interaction between the terrain surface and air movement results in wind speed values varying with height. The vertical profile of wind speed is strongly linked to the land type. Flat areas produce lower wind disturbance than built-up areas [35][36][37]. In wind energy, the wind profile is typically explained according to the Equation (5) or (6): After the Equation (5) was transformed, the α time exponent was calculated. After substitution of measurement data listed in Table 2, its mean value was determined for both locations. For farm A, α = 0.256 was obtained, whereas for farm B α = 0.237. Subsequently, average wind speed at h = 120 m was calculated with the use of Equation (5)  Maximum heights of the wind measurements for both farms were lower than the planned height of wind turbine towers. Knowing the average wind speed at the desired height (120 m), the wind speed distribution was generated using two-parameter Weibull function. It must be noted that the provided parameters are a mathematical result. Though different wind speed distribution models are applied to fit the wind speed over a time period, the two-parameter Weibull function is accepted as the most popular technique [38].
The two-parameter Weibull probability density function is expressed by: where v, k, A > 0. Dimensionless factor k determines the shape of the curve and is called a shape factor. Parameter A is the scale parameter. The distributions take different shapes with different values of k and A. Parameter k specifies the shape of a Weibull distribution and takes on a value of between 1 and 3. A small value for k signifies very variable winds, while constant winds are characterized by a larger k. Parameter A was calculated on the basis of the following relationship: With the wind speed distributions at the measured height (Table 2) being available, the Weibull distribution was adjusted to them. It was established that the k parameter shape ranges in both locations from 2.1 to 2.5. Further analysis was conducted for three k parameter values, that is: 2.1, 2.3 and 2.5. Figures 2 and 3 show Weibull probability density function results for both locations.
Dimensionless factor k determines the shape of the curve and is called a shape factor. Parameter A is the scale parameter. The distributions take different shapes with different values of k and A. Parameter k specifies the shape of a Weibull distribution and takes on a value of between 1 and 3. A small value for k signifies very variable winds, while constant winds are characterized by a larger k. Parameter A was calculated on the basis of the following relationship: With the wind speed distributions at the measured height (Table 2) being available, the Weibull distribution was adjusted to them. It was established that the k parameter shape ranges in both locations from 2.1 to 2.5. Further analysis was conducted for three k parameter values, that is: 2.1, 2.3 and 2.5. Figures 2 and 3 show Weibull probability density function results for both locations.  Percentage results obtained from the probability density function were multiplied by 8760 (total number of hours per year) in each wind speed class. Thus, the number of hours per year for each speed class were obtained.

Wind Turbine Selection
Selection of wind turbine type and estimation of its energy performance for both locations was obtained based on the wind speed distribution histogram- Figures 2 and 3. The calculations were performed considering the wind turbine characteristics provided

Wind Turbine Selection
Selection of wind turbine type and estimation of its energy performance for both locations was obtained based on the wind speed distribution histogram- Figures 2 and 3. The calculations were performed considering the wind turbine characteristics provided by manufacturer, presenting the relationship between turbine power and wind speed- Table 3. The available wind turbines power depends, among others, on the air density [38,39], which is a function of pressure and temperature-Equation (10).
Change in the pressure with altitude can be presented with Equation (11).
Based on the measurement data, it was determined that the temperature gradient in the studied locations is 0.5 K every 100 m, whereas air density in these locations is approximately ρ = 1.24 kg/m 3 . Unfortunately, wind turbine manufacturers rarely provide the performance of their devices for different air density values. Out of the selected range of turbines, only half were provided with such information. In the majority of devices, the power curve for air density ρ = 1.225 kg/m 3 is presented. Not willing to restrict the analysis to three devices, further calculations were conducted for air density of ρ = 1.225 kg/m 3 .
Considering the Weibull distributions (Figures 2 and 3) and the power curves of the selected turbines listed in Table 3, Figures 4-9 show the distribution of the wind turbine performance in the studied locations for the different k parameters. formance of their devices for different air density values. Out of the selected range of turbines, only half were provided with such information. In the majority of devices, the power curve for air density ρ = 1.225 kg/m 3 is presented. Not willing to restrict the analysis to three devices, further calculations were conducted for air density of ρ = 1.225 kg/m 3 .
Considering the Weibull distributions (Figures 2 and 3) and the power curves of the selected turbines listed in Table 3, Figures 4-9 show the distribution of the wind turbine performance in the studied locations for the different k parameters.

Results and Discussion
Analyses discussed in the Section 3 allowed obtaining data concerning the performance of the selected wind turbines. The G97 turbine turned out to be a clear leader in the studied locations. It generated the highest amount of energy that was supplied to the power grid, independently of the shape parameter k. The lowest productivity in the tested locations was demonstrated by the W2E-100 turbine. Figures 12 and 13 demonstrate Weibull distribution and power production distribution, as well as power curves for the G97 and W2E-100 turbine. Data analysis indicates that the W2E-100 turbine attains its maximum power output at 13 m/s wind speed. This is considerably beyond the maximum power production capacity in the selected locations. The G97 attains the maximum power output for the wind speed of 11 m/s, which enables it to achieve higher performance.

Results and Discussion
Analyses discussed in the Section 3 allowed obtaining data concerning the performance of the selected wind turbines. The G97 turbine turned out to be a clear leader in the studied locations. It generated the highest amount of energy that was supplied to the power grid, independently of the shape parameter k. The lowest productivity in the tested locations was demonstrated by the W2E-100 turbine. Figures 12 and 13 demonstrate Weibull distribution and power production distribution, as well as power curves for the G97 and W2E-100 turbine. Data analysis indicates that the W2E-100 turbine attains its maximum power output at 13 m/s wind speed. This is considerably beyond the maximum power production capacity in the selected locations. The G97 attains the maximum power output for the wind speed of 11 m/s, which enables it to achieve higher performance. locations was demonstrated by the W2E-100 turbine. Figures 12 and 13 dem Weibull distribution and power production distribution, as well as power curve G97 and W2E-100 turbine. Data analysis indicates that the W2E-100 turbine a maximum power output at 13 m/s wind speed. This is considerably beyond the m power production capacity in the selected locations. The G97 attains the maximum output for the wind speed of 11 m/s, which enables it to achieve higher performa  Table 4 lists performance coefficients of the analyzed wind turbines depen the assumed k shape coefficient. The energy performance coefficient is the quotie actual annual production and the technically possible maximum energy produc wind turbine. It should be noted that the wind turbines are not designed to maxi energy performance coefficient, but rather to generate the highest possible pow termined wind speeds. Performance coefficients of 30-40% are considered very coastal areas.   Table 4 lists performance coefficients of the analyzed wind turbines depending on the assumed k shape coefficient. The energy performance coefficient is the quotient of the actual annual production and the technically possible maximum energy production of a wind turbine. It should be noted that the wind turbines are not designed to maximize the energy performance coefficient, but rather to generate the highest possible power at determined wind speeds. Performance coefficients of 30-40% are considered very high in coastal areas. The average cost of energy production for land wind turbines in 2017 was 60 $/MWh [2]. Table 5 lists annual income from energy production of the presented turbines depending on the assumed k shape coefficient. The maximum difference between financial profit from G97, and W2E-100 amounted to 82,000$ per year. The difference in financial profit gained from energy production by these two wind turbines will reach 1,640,000$, while 20 years of their functioning.
And the maximum difference between financial profit from G97 and V100 is 28,000$ per year. In the period of 20 years, the income from the G97 turbine will increase by 560,000$. In this case, the winner is not as obvious. Purchase cost as well as service costs may be of significance when selecting the device.

Conclusions
The present study demonstrated the manner in which wind turbine is selected on the basis of recorded annual wind measurements, with the emphasis on the obtaining the maximum financial benefits. The wind measurements demonstrated applicability of the tested locations in terms of their use as the construction site of a wind farm. Six types of wind turbines with different power outputs were tested. Turbines ensuring best usage of the wind energy resources in the studied locations have been indicated. Considering the hourly distribution of individual wind speeds, 2 MW turbines turned out to be the most energy efficient. The turbines with nominal power output of 2.3-2.5 MW demonstrated poorest performance in the tested locations.
The wind characteristics shall be analyzed for the site, where the wind turbine is to be located. Possible errors of performance estimation may stem from inaccurate prediction of the processed energy. In general, the wind measurements are performed at several heights, but typically below the height of the wind turbine boss. The calculation of the average wind speed value to a different height requires a precise analysis of the land topography. An incorrect assumption of the roughness index may result in overestimation or underestimation of the future wind farm performance.
The k Weibull shape coefficient has less pronounced impact on the distribution of individual wind speeds. At the same time, it has been demonstrated that a well selected wind turbine can be less sensitive to changes of the k coefficient. The analysis was performed on the basis of a one-year distribution of wind speed. It is a known fact that wind distribution will vary in time of wind turbines operation, and that it will oscillate around the multi-annual average value.