Metal-Air Batteries—A Review

Metal–air batteries are a promising technology that could be used in several applications, from portable devices to large-scale energy storage applications. This work is a comprehensive review of the recent progress made in metal-air batteries MABs. It covers the theoretical considerations and mechanisms of MABs, electrochemical performance, and the progress made in the development of different structures of MABs. The operational concepts and recent developments in MABs are thoroughly discussed, with a particular focus on innovative materials design and cell structures. The classical research on traditional MABs was chosen and contrasted with metal–air flow systems, demonstrating the merits associated with the latter in terms of achieving higher energy density and efficiency, along with stability. Furthermore, the recent applications of MABs were discussed. Finally, a broad overview of challenges/opportunities and potential directions for commercializing this technology is carefully discussed. The primary focus of this investigation is to present a concise summary and to establish future directions in the development of MABs from traditional static to advanced flow technologies. A systematic analysis of this subject from a material and chemistry standpoint is presented as well.


Introduction
Researchers and politicians are becoming increasingly focused on energy storage as the awareness of the environmental implications that come with relying on fossil commodities and the reliability and long-term durability of electricity networks increases across the globe. Energy storage can assist in resolving the issue of intermittency associated with wind and solar power; in some cases, this can react quickly to substantial demand changes, allowing the grid to respond more rapidly and reducing the need to implement backup power plants. Energy storage is becoming increasingly popular. The efficiency of an energy storage facility is defined by the speed with which it can react to changes in demand, the total amount of energy it can store, the rate at which energy is lost throughout the storage process, and the ease with which it can be recharged. Solar PV only provides electricity during the day, at its most productive. Every day brings a new level of total output. Wind energy output is erratic, yet it may be spread around the world. On the other hand, average It has been shown that in certain non-ideal situations, the precipitation of the solid discharge product may consume active electrolyte components, lowering the energy density that can be achieved [24]. The investigation of a wide range of metal-air chemistries is continuing. Mg-air systems are attractive because of the uniform deposition of Mg metal [25][26][27], but the corrosion of the Mg electrode severely restricts aqueous Mg-air batteries. Several ionic liquid electrolytes have been suggested for use in magnesium-air systems. Still, they all suffer from electrochemical instability [28], especially noticeable during charging, and the cell's reversibility is restricted. Al-air is another intriguing candidate to consider. As an available and safe element, aluminum is used in the production of Al-air batteries, which provide both a high theoretical energy density and high specific energy values [29][30][31]. A combination of sodium's abundant natural supply and safety, as well as its characteristics that are similar to lithium, has fueled research into Na-air batteries [32][33][34]. The development of these systems is still in its stage. Si-air batteries have also received a lot of attention recently [35]. They have a high theoretical energy density and are stable in electrolytes, including aqueous solutions. However, the reversibility of the solid discharge product, precipitation, and pore blockage are all issues that are presently being addressed in experimental investigations of Si-air systems in both ionic liquid and alkaline electrolytes. Li-air and Zn-air are two of the most promising metal-air systems now under study [36,37], with Li-air being the most promising. Lithium-air batteries (LABs) have been studied for decades [38], but they have only recently emerged as a highly explored subject in the scientific community. The electrolyte has proven to be a stumbling block in the advancement of LAB technology. The aprotic (non-aqueous) and aqueous electrolyte combinations used in Li-air systems are the most often seen. The use of mixed electrolyte systems has been suggested. The first wave of LAB investigation concentrated on aprotic It has been shown that in certain non-ideal situations, the precipitation of the solid discharge product may consume active electrolyte components, lowering the energy density that can be achieved [24]. The investigation of a wide range of metal-air chemistries is continuing. Mg-air systems are attractive because of the uniform deposition of Mg metal [25][26][27], but the corrosion of the Mg electrode severely restricts aqueous Mg-air batteries. Several ionic liquid electrolytes have been suggested for use in magnesium-air systems. Still, they all suffer from electrochemical instability [28], especially noticeable during charging, and the cell's reversibility is restricted. Al-air is another intriguing candidate to consider. As an available and safe element, aluminum is used in the production of Al-air batteries, which provide both a high theoretical energy density and high specific energy values [29][30][31]. A combination of sodium's abundant natural supply and safety, as well as its characteristics that are similar to lithium, has fueled research into Na-air batteries [32][33][34]. The development of these systems is still in its stage. Si-air batteries have also received a lot of attention recently [35]. They have a high theoretical energy density and are stable in electrolytes, including aqueous solutions. However, the reversibility of the solid discharge product, precipitation, and pore blockage are all issues that are presently being addressed in experimental investigations of Si-air systems in both ionic liquid and alkaline electrolytes. Li-air and Zn-air are two of the most promising metal-air systems now under study [36,37], with Li-air being the most promising. Lithium-air batteries (LABs) have been studied for decades [38], but they have only recently emerged as a highly explored subject in the scientific community. The electrolyte has proven to be a stumbling block in the advancement of LAB technology. The aprotic (non-aqueous) and aqueous electrolyte combinations used in Li-air systems are the most often seen. The use of mixed electrolyte systems has been suggested. The first wave of LAB investigation concentrated on aprotic electrolytes, which was the start of the wave. Using the aprotic Li-air system (LiPF6 in ethylene carbonate (EC)), Abraham et al. [39] suggested an overall reaction resulting in the formation of Li  solvents were used in the first generation of aprotic Li-air cells; however, it has subsequently been shown that carbonate solvents are unstable, releasing lithium carbonates during discharging and emitting CO 2 during charging [40]. In recent years, carbonate electrolytes have mostly been phased out in favor of ether and ester solvents in conjunction with lithium salts. The precipitation of Li 2 O 2 poses a second difficulty for LABs in aprotic electrolytes, which presents the third obstacle. When this solid precipitates in the cathode, it may create a thick layer over the carbon surface, preventing electrons from transferring between it and the anode. It is possible that whole pores in the cathode may become closed as precipitation proceeds, resulting in the electrode being passivated and reducing the cell's capacity. Finally, it has been shown that oxygen transport in aprotic electrolytes may be a difficult component to control in LAB effectiveness, particularly at higher current densities [41]. This has prompted researchers to draw lessons from the success of the gas diffusion electrode in fuel cells and to continue studies of LABs using aqueous electrolytes as an alternative. It is widely known that Li metal interacts strongly with water, which has traditionally restricted aqueous electrolytes in Li-air systems. However, the usage of aqueous electrolytes has recently been expanded. When a glass-ceramic layer over the Li electrode was successfully suggested in 2004, it allowed for the electrochemical process to continue while also protecting the metal electrode [42]. In alkaline aqueous electrolytes, the discharge product is LiOH H 2 O rather than Li 2 O 2 , indicating that the electrolyte is alkaline. These systems allow for LiOH to precipitate at the separator-anode interface, which lowers the danger of pore-clogging in the cathode, which has been seen in aprotic laboratory systems. While in the presence of air, dissolved CO 2 interacts with OHto create carbonates, which gradually decreases the conductivity of the electrolyte and shortens its lifespan. When exposed to water, dissolved CO 2 reacts with OH-to form carbonates, which further shortens the cell's lifetime. Many theoretical studies have highlighted the impressive possibilities of these systems [42], and the company International Business Machines (IBM) has sought the expansion of LABs for industrial purposes. IBM has also pursued the growth of LABs for commercial applications. Even though there are still major difficulties [43,44], the future of LABs seems bright. Zinc-air batteries (ZABs) are the only completely developed metal-air system now available, and they have been successfully marketed as primary cells for many decades. Hearing aids, for example, are a low-current application that they are particularly suited for. Their lifespan and electrical rechargeability, on the other hand, are both limited [45]. One significant benefit of Zn as an electrode material is that it is stable in water, unlike Li, which is a significant advantage. Alternate near-neutral aqueous [46] and ionic liquid electrolytes have been suggested in an attempt to enhance the rechargeability of ZABs. Current research continues to be focused on material development to overcome the lifespan limits of these systems and cell engineering to enhance the effectiveness of the system. However, although some obstacles persist, the advancement of secondary ZABs has progressed to the point where they may be feasible for stationary storage applications. Some start-ups, such as Eos Energy Storage and Fluidic Energy [47], are working to commercialize the innovation. Zn-air systems provide one of the most rapid and dependable routes to today's practical secondary metal-air battery systems.

MABs' Theoretical Considerations and Mechanisms
As a result of the oxygen being kept outside the battery, MABs are a viable choice among several other types of energy storage devices. The oxygen-evolution reaction (OER) and the oxygen-reduction reaction (ORR) are the two processes related to oxygen. Generally speaking, MABs function in an open system [48]. The components are represented by the schematic design seen in Figure 2. This system comprises three basic parts: a metal anode, a porous air cathode, and an electrolyte that separates the two electrodes from one another. As implied by the name, the anode material of a metal-air battery is composed of metals such as lithium Li, sodium Na, iron Fe, zinc Zn, and other elements. There are many types of electrolytes available [49]. They include: aqueous electrolytes, non-aqueous (aprotic), solid-state, and hybrid electrolytes. Because of their extraordinary sensitivity to water, lithium-air, potassium-air, and sodium-air batteries were often used in non-aqueous systems. While anodes composed of magnesium, aluminum, iron, or zinc are compatible with aqueous electrolytes, these aqueous systems need the addition of a hydrophobic protective layer to prevent electrolyte leakage [48].
Energies 2021, 14, x FOR PEER REVIEW 5 of 48 from one another. As implied by the name, the anode material of a metal-air battery is composed of metals such as lithium Li, sodium Na, iron Fe, zinc Zn, and other elements. There are many types of electrolytes available [49]. They include: aqueous electrolytes, non-aqueous (aprotic), solid-state, and hybrid electrolytes. Because of their extraordinary sensitivity to water, lithium-air, potassium-air, and sodium-air batteries were often used in non-aqueous systems. While anodes composed of magnesium, aluminum, iron, or zinc are compatible with aqueous electrolytes, these aqueous systems need the addition of a hydrophobic protective layer to prevent electrolyte leakage [48]. In MABs, metal changes into ions on the anodic electrode, while the oxygen transforms into hydroxide ions at the cathodic electrode. This is in contrast to the operating approach of a conventional ionic battery, which sees metallic ions transition from the anode to cathode. The diffusion of oxygen into the MAB occurs via a layer known as the gas diffusion layer. The behavior of oxygen in an aqueous electrolyte medium differs from that of oxygen in a non-aqueous electrolyte, as depicted in Figure 3.
During the transition of the metal into metallic ions, electrons are produced, and the metallic ions subsequently dissolve into the electrolyte. During a charging operation, all of these steps are reversed. The reaction formulae for several MABs are shown in Table 2.  In MABs, metal changes into ions on the anodic electrode, while the oxygen transforms into hydroxide ions at the cathodic electrode. This is in contrast to the operating approach of a conventional ionic battery, which sees metallic ions transition from the anode to cathode. The diffusion of oxygen into the MAB occurs via a layer known as the gas diffusion layer. The behavior of oxygen in an aqueous electrolyte medium differs from that of oxygen in a non-aqueous electrolyte, as depicted in Figure 3. from one another. As implied by the name, the anode material of a metal-air battery is composed of metals such as lithium Li, sodium Na, iron Fe, zinc Zn, and other elements. There are many types of electrolytes available [49]. They include: aqueous electrolytes, non-aqueous (aprotic), solid-state, and hybrid electrolytes. Because of their extraordinary sensitivity to water, lithium-air, potassium-air, and sodium-air batteries were often used in non-aqueous systems. While anodes composed of magnesium, aluminum, iron, or zinc are compatible with aqueous electrolytes, these aqueous systems need the addition of a hydrophobic protective layer to prevent electrolyte leakage [48]. In MABs, metal changes into ions on the anodic electrode, while the oxygen transforms into hydroxide ions at the cathodic electrode. This is in contrast to the operating approach of a conventional ionic battery, which sees metallic ions transition from the anode to cathode. The diffusion of oxygen into the MAB occurs via a layer known as the gas diffusion layer. The behavior of oxygen in an aqueous electrolyte medium differs from that of oxygen in a non-aqueous electrolyte, as depicted in Figure 3.
During the transition of the metal into metallic ions, electrons are produced, and the metallic ions subsequently dissolve into the electrolyte. During a charging operation, all of these steps are reversed. The reaction formulae for several MABs are shown in Table 2.  During the transition of the metal into metallic ions, electrons are produced, and the metallic ions subsequently dissolve into the electrolyte. During a charging operation, all of these steps are reversed. The reaction formulae for several MABs are shown in Table 2.
Iron Fe Alkaline aqueous Zinc Zn

Cell Potential
The cell potential is determined by calculating the potential difference between the anodic and cathodic electrodes, as shown in the following equation [54,55]. The resulting value is expressed as a volt unit (V), as shown in Equation (1).
If the standard circumstances are altered, the Nernst equation may be used as a guideline to calculate: which is derived from Gibbs free energy This is calculated using the balanced reaction equation and thermodynamic tables. When ∆G is a positive value, it implies the reaction requires external energy (nonspontaneous reaction), while when it is a negative value, the reaction can occur in the absence of external energy (spontaneous reaction) [54][55][56].

Energy Efficiency
The energy efficiency of a rechargeable battery is subdivided into three parts. First, the charging energy efficiency η charg , which is equal to the net energy ∆Q n divided by charge energy Q in , as calculated as follows SOC(t) = SOC(0) − Idt C n (I is positive when discharging the battery) which SOC refers to the state of charge, U is the battery voltage and C n is the battery standard capacity. Secondly, the discharging energy efficiency; where the discharge energy is Finally, the charge-discharge energy efficiency is given as The charge energy Q in and discharge energy Q out can be calculated from the automatically recording data of the voltage, current, and time [57].

Electrochemical Performance of MABs
From the results of many tests, many kinds of metal utilized in MABs, such as Zn-air, Fe-air, Al-air/Al-O 2 , Li-air/Li-O 2 , and Si-air batteries, may offer medium-specific power and good specific energy. Additionally, as depicted in Figure 3, the prospective efficiency of MABs was contrasted with that of Li-ion (LIB) as well as metal-sulfur batteries. The specific energy supplied by prospective MABs, advanced metal-S batteries, and LIBs ranges from 500 to 1500 Wh/kg Me, up to 500 Wh/kg, and 200 to 300 Wh/kg, respectively, in terms of specific energy. While the specific power provided by prospective MABs, advanced metal-S batteries, and LIBs range from 0.1-1 kW/kg Me, up to 1 kW/kg, as well as up to 10 kW/kg. The specific power delivered by MABs, advanced metal-S batteries, and LIBs ranges from 0.1-1 kW/kg Me. The numbers on the right-hand side of Figure 4 reflect the possible future effectiveness of certain MABs [58], which are not yet available. which SOC refers to the state of charge, U is the battery voltage and is the battery standard capacity. Secondly, the discharging energy efficiency; where the discharge energy is Finally, the charge-discharge energy efficiency is given as The charge energy and discharge energy can be calculated from the automatically recording data of the voltage, current, and time [57].

Electrochemical Performance of MABs
From the results of many tests, many kinds of metal utilized in MABs, such as Znair, Fe-air, Al-air/Al-O2, Li-air/Li-O2, and Si-air batteries, may offer medium-specific power and good specific energy. Additionally, as depicted in Figure 3, the prospective efficiency of MABs was contrasted with that of Li-ion (LIB) as well as metal-sulfur batteries. The specific energy supplied by prospective MABs, advanced metal-S batteries, and LIBs ranges from 500 to 1500 Wh/kg Me, up to 500 Wh/kg, and 200 to 300 Wh/kg, respectively, in terms of specific energy. While the specific power provided by prospective MABs, advanced metal-S batteries, and LIBs range from 0.1-1 kW/kg Me, up to 1 kW/kg, as well as up to 10 kW/kg. The specific power delivered by MABs, advanced metal-S batteries, and LIBs ranges from 0.1-1 kW/kg Me. The numbers on the right-hand side of Figure 4 reflect the possible future effectiveness of certain MABs [58], which are not yet available. Although a Li-air battery showed a high OCV of 2.91 V and high theoretical energy density, its lifetime was short, as it failed after two cycles due to the corrosion of the lithium anode by the electrolyte. A Na-air battery fabricated using a 3D tin sulfide nanopetals cathode showed a high round trip efficiency of 83%, a low overpotential gap of 0.52 V, good rechargeability (40 cycles), and a high power density of 300 W/kg [59]. The good performance was related to the 3D tin sulfide cathode that provides active sites for effi- Although a Li-air battery showed a high OCV of 2.91 V and high theoretical energy density, its lifetime was short, as it failed after two cycles due to the corrosion of the lithium anode by the electrolyte. A Na-air battery fabricated using a 3D tin sulfide nano-petals cathode showed a high round trip efficiency of 83%, a low overpotential gap of 0.52 V, good rechargeability (40 cycles), and a high power density of 300 W/kg [59]. The good performance was related to the 3D tin sulfide cathode that provides active sites for efficient diffusion of electrolyte and air [59]. An Al-air battery had an OCV of 1.2 V, the theoretical energy density of 2.98 Ah/g, and specific energy of 200 Wh/Kg [31]. The specific capacity of an Al-air battery with a chitosan hydrogel membrane and 10% SiO 2 achieved a specific capacity of 288.5 mAh/g at 1 mA/cm 2 due to the generation of SiO 3 2− , which is considered a corrosion inhibitor [60]. Additionally, an Mg-air battery showed a specific energy density of 3.9 kWh/Kg and a theoretical volumetric density of 14 kWh/L [28]. Adding vanadate or phosphate as a corrosion inhibitor to the NaCl electrolyte significantly improved the performance of Mg-air batteries, and phosphate showed a stronger inhibiting effect than vanadate [61]. Zinc is a cheap and abundant metal; thus, the cost of ZABs is quite low. A Zn-air battery realized a theoretical energy density of 0.82 Ah/g. A Zn-air battery with Co-MOF as cathode catalyst achieved a power density of 86.2 mW/cm 2 and outstanding charge-discharge performance [62]. Additionally, a Zn-air battery with Ni 3 Fe/N-S-CNT as the cathode electrocatalyst achieved 180 mW/cm 2 (power density) and long-term stability for 500 h [63]. A Fe-air battery had a specific charge capacity of 300 Ah/Kg, the theoretical open-circuit voltage of 1.28 V, charge efficiency of 96%, voltage efficiency of 40%, and energy efficiency of 35% [51]. A 3D-printed Fe-air battery with nanocomposite electrodes and showed a cell voltage of 0.76 V, the maximum charge capacity of 814 mA h/g at 10 mA/cm 2 , and an energy density of 453 Wh/Kg [64]. The Sn-air battery is another type of metal-air battery, with an OCV of 0.95 V and 860 Wh/Kg specific energy. A Sn-air battery operated at room temperature with an electrolyte of methane sulfonic acid and polyacrylamide gel achieved a maximum power density of 5 mW/cm 2 at 12 mA/cm 2 for 24 h [65]. The following table (Table 3) summarizes the main differences between the reported MABs.

Anode of MABs
Since the invention of the first metal-air battery, the zinc-air battery, in 1878, a great deal of development and study has been carried out, and Figure 5 displays a summary of some of these advancements [75]. Many metals, including zinc, aluminum, iron, lithium, sodium, potassium, and magnesium, may be used as anodes in MABs. Each metal has its own set of benefits and drawbacks when it comes to being used as anode electrodes. The energy density of LABs is the greatest theoretically possible (11,140 Wh/kg) among the many kinds of MABs; however, obtaining rechargeable LABs (LABs) is difficult. On the other hand, metals such as zinc (0.82 Ah g(−1), magnesium (2.20 Ah g(−1), as well as aluminum (Al) are ecologically benign, plentiful, commercially viable, as well as reasonably safe. Furthermore, Al is readily available for recycling in massive amounts, and it has a higher energy density (8.1 kWh·kg(−1)), as well as a significant theoretical voltage (2.7 V). As a result, AABs are considered to be the second most energy-dense battery after Li.
The chemical activity of the anode determines the discharge capacity of the anode. Because of the high activity of the metal, a side reaction with various components of the electrolyte may occur that cannot be avoided. These reactions may occur at different rates and have varying effects on battery efficiency, subject to the purity of metal and the storing conditions [28]. A list of theoretical specific energies for each kind of metal-air battery is provided in Table 4, with the specific energy computed using the following formula: where W denotes the specific energy of the material, n denotes the number of atoms that have been transported, M denotes the molar mass, whilst U cell is the cell voltage. Table 5 contains experimental findings [58], representing the most relevant results that have been published.
and have varying effects on battery efficiency, subject to the purity of metal and the storing conditions [28]. A list of theoretical specific energies for each kind of metal-air battery is provided in Table 4, with the specific energy computed using the following formula: where W denotes the specific energy of the material, n denotes the number of atoms that have been transported, M denotes the molar mass, whilst Ucell is the cell voltage. Table 5 contains experimental findings [58], representing the most relevant results that have been published.      Progress Done in the Anode of MAB As discussed above, several metals, such as zinc, aluminum, iron, lithium, sodium, potassium, and magnesium, can be used as anodes in MABs. Each metal has its advantages and disadvantages. The Al-air battery has unique features, such as high energy density, light weight, good recyclability, environmentally friendly, and cheap. Moreover, the electrolyte can be an alkaline, salty, and non-aqueous solution [86]. Therefore, we will focus in this section on the progress made in Al-air batteries.
The performance of an ultrafine-grain (UFG) aluminum anode produced by equal channel angular pressing (ECAP) ( Figure 6) in three distinct electrolytes (NaOH, KOH, and NaCl) was studied at a constant discharge current of 10 mA cm −2 . The cathode was an air electrode with gas diffusion and catalyst (Ag powder) layers as a double-layer structure, laminated with a current collector (Ni mesh). The UFG was also compared with coarse-grained (CG) aluminum. The results shown in Table 6 indicate that the grain with finer sizes enhanced the battery's performance in alkaline electrolytes because of the active dissolution of the aluminum anode. However, due to the local corrosion and the oxide film blockage in NaCl electrolyte, the study results show that changing the Al anode grain to a fine size has no effect on performance. The anode efficiency of CG and UFG in NaOH is 55.3% and 77.4%, respectively. Moreover, the energy density improved by 55.5% with a finer grain size relative to CG, but the effect in NaCl and KOH solutions is not clear [87]. Conditions: a is anode sheet/foil, b is porous/particulate anode, c is full-cell measurements, d is 100% deep discharge, e is repeated charge/discharge, and f is elevated temperature.

Progress Done in the Anode of MAB
As discussed above, several metals, such as zinc, aluminum, iron, lithium, sodium, potassium, and magnesium, can be used as anodes in MABs. Each metal has its advantages and disadvantages. The Al-air battery has unique features, such as high energy density, light weight, good recyclability, environmentally friendly, and cheap. Moreover, the electrolyte can be an alkaline, salty, and non-aqueous solution [86]. Therefore, we will focus in this section on the progress made in Al-air batteries.
The performance of an ultrafine-grain (UFG) aluminum anode produced by equal channel angular pressing (ECAP) ( Figure 6) in three distinct electrolytes (NaOH, KOH, and NaCl) was studied at a constant discharge current of 10 mA cm −2 . The cathode was an air electrode with gas diffusion and catalyst (Ag powder) layers as a double-layer structure, laminated with a current collector (Ni mesh). The UFG was also compared with coarse-grained (CG) aluminum. The results shown in Table 6 indicate that the grain with finer sizes enhanced the battery's performance in alkaline electrolytes because of the active dissolution of the aluminum anode. However, due to the local corrosion and the oxide film blockage in NaCl electrolyte, the study results show that changing the Al anode grain to a fine size has no effect on performance. The anode efficiency of CG and UFG in NaOH is 55.3% and 77.4%, respectively. Moreover, the energy density improved by 55.5% with a finer grain size relative to CG, but the effect in NaCl and KOH solutions is not clear [87].   Two aluminum anodes with different purity percentages were compared to examine the impact of the impurity on the performance of the aluminum-air batteries. The tested anodes were a 2N5 purity 99.5% and a 4N purity 99.99% grade aluminum anode. The experimental results show that the 2N5 grade Al showed a lower battery performance than the 4N grade Al due to the impurities that shaped the complex layer containing iron, silicon, cupper, and other elements. This impurity layer of 2N5 aluminum decreases the battery's voltage on standby status and depletes the battery efficiency and the discharge current at 1 volt; however, lower voltages of 0.8 volts lead to the layer dissolving, and thus the performance improved. The results at the two different applied potentials are shown in Table 7. We can conclude that the impurity complex layer reduced with a declining discharge voltage. This phenomenon improves battery efficiency and discharges current density by reducing the self-corrosion reaction. Therefore, it is possible to use the cheaper 2N5 grade aluminum anode instead of 4N Al at the condition of high-power discharge for aluminum-air batteries [88]. Zinc is considered an effective alloying element for the anode of an aluminum-air battery to increase the nominal cell voltage and decrease the self-corrosion rate. However, a study found that Zn added to Al 99.7% purity anode decreased its discharge performance due to the formation of Zn oxidation film. Additionally, to overcome this formation, indium (In) was added to an aluminum-zinc anode, which showed improvement in the discharge performance of Al-air batteries by reducing the resistance of zinc oxidation film via In ions. Moreover, an Al-Zn-In alloy anode that is made of commercial-grade aluminum (99.7% purity) has a cheaper cost than 4N grade aluminum (99.99% purity) [89].

MABs Electrolyte
As depicted in Figure 7 [16], the electrolyte for MABs may be aqueous, non-aqueous, solid-state, or hybrid in nature. This section covers the recent progress made in the different electrolytes used in MABs.

Aqueous Electrolyte
Aqueous electrolyte possesses highly ionic conductivity. Additionally, it is attractive for batteries with high power density. Additionally, water-based electrolytes are nonflammable and low-cost. However, the aqueous electrolyte is more corrosive than an organic solution. On the other hand, it has a limited water thermodynamic electrochemical window. The range of its thermal application is narrower, as its performance at low temperatures is limited by the freezing point [90]. Aqueous electrolytes can be grouped into three solutions based on the pH number [16].
Alkaline: The alkaline electrolyte solution has a pH value above 7 and lower or equal to 14, and is the most used electrolyte in the aqueous-based MABs compared to an acidic electrolyte, due to its favorable ORR with lower overpotential and faster reaction kinetics. However, when CO2 from the air environment interacts with this electrolyte, it forms a carbonate surrounding the cathode. A high quantity of carbonate reduces the cathode's efficiency because it obstructs the pores of the positive electrode [16]. In addition, using strong alkaline electrolytes is harmful to the environment. Zinc-air and aluminum-air batteries usually use aqueous alkaline electrolytes. MABs with alkaline electrolytes can afford better electrocatalysis activity of oxygen and higher resistance to metal corrosion than neutral and acidic electrolytes. Examples of alkaline electrolytes include KOH, LiOH, and NaOH; however, the most employed in MABs is the concentrated KOH solution, due to it having the lowest viscosity and highest ionic conductivity [75]. The discharge behavior of the recently presented Si-air battery in the alkaline electrolyte has been investigated using different concentrations of KOH electrolyte. Siliconair cell of refill type shown in Figure 8 was used. When the KOH concentration is between 2 M-5 M, the discharge potential dependence on the concentration is almost stable, while it decreases significantly only at lower concentrations up to 1 M, with the difference in discharge potential between high and low concentrations being 100 mV. In contrast, there

Aqueous Electrolyte
Aqueous electrolyte possesses highly ionic conductivity. Additionally, it is attractive for batteries with high power density. Additionally, water-based electrolytes are nonflammable and low-cost. However, the aqueous electrolyte is more corrosive than an organic solution. On the other hand, it has a limited water thermodynamic electrochemical window. The range of its thermal application is narrower, as its performance at low temperatures is limited by the freezing point [90]. Aqueous electrolytes can be grouped into three solutions based on the pH number [16].
Alkaline: The alkaline electrolyte solution has a pH value above 7 and lower or equal to 14, and is the most used electrolyte in the aqueous-based MABs compared to an acidic electrolyte, due to its favorable ORR with lower overpotential and faster reaction kinetics. However, when CO 2 from the air environment interacts with this electrolyte, it forms a carbonate surrounding the cathode. A high quantity of carbonate reduces the cathode's efficiency because it obstructs the pores of the positive electrode [16]. In addition, using strong alkaline electrolytes is harmful to the environment. Zinc-air and aluminum-air batteries usually use aqueous alkaline electrolytes. MABs with alkaline electrolytes can afford better electrocatalysis activity of oxygen and higher resistance to metal corrosion than neutral and acidic electrolytes. Examples of alkaline electrolytes include KOH, LiOH, and NaOH; however, the most employed in MABs is the concentrated KOH solution, due to it having the lowest viscosity and highest ionic conductivity [75].
The discharge behavior of the recently presented Si-air battery in the alkaline electrolyte has been investigated using different concentrations of KOH electrolyte. Silicon-air cell of refill type shown in Figure 8 was used. When the KOH concentration is between 2 M-5 M, the discharge potential dependence on the concentration is almost stable, while it decreases significantly only at lower concentrations up to 1 M, with the difference in discharge potential between high and low concentrations being 100 mV. In contrast, there was no impact of the KOH concentration on the open cell potential in this experiment. Because OH − alters the conductivity and activity of the electrolyte, increasing the KOH concentration up to 6 M resulted in a linear rise in ionic conductivity. The application of discharge current, as well as the concentration of KOH, may have an impact on the roughness of the Si surface [80]. Cathode: Corrosion: Si + 2OH + 2H O → SiO (OH) +2H (14) Figure 8. A refill type of Si-air cell, with permission to reproduce from [80].

Neutral:
The neutral solution has a pH value of 7, and it has been demonstrated to increase both the cycle stability and the lifespan of secondary ZABs; however, at this time, no modeling studies have evaluated the performance of neutral ZABs in a laboratory setting. The pH stability of neutral ZABs is a key element in cell function. Additionally, an aluminum alloy-air battery can discharge with higher activity and lower corrosion rate in Figure 8. A refill type of Si-air cell, with permission to reproduce from [80]. Anode: Cathode: Corrosion: Neutral: The neutral solution has a pH value of 7, and it has been demonstrated to increase both the cycle stability and the lifespan of secondary ZABs; however, at this time, no modeling studies have evaluated the performance of neutral ZABs in a laboratory setting. The pH stability of neutral ZABs is a key element in cell function. Additionally, an aluminum alloy-air battery can discharge with higher activity and lower corrosion rate in a neutral salt solution than in an alkaline electrolyte [16].
Acidic: The acidic solution has a pH between 2 and less than 7. It is rarely applied in aqueous-based MABs due to the decreased battery efficiency via a large amount of H + in the solution that reacts directly with metal. Different types of acids at the same pH, operation temperature, and concentration change an Al-Zn alloy anode's performance [16]. Acidic solution suppressed the formation of byproducts on the cathode and the formation of dendrite on the anode. However, it can result in corrosion problems for some types of MABs [91].

Electrolyte Additives
In an aqueous electrolyte, the metal electrode suffers from critical issues, including electrode corrosion, passivation, hydrogen evolution, and dendrite formation. The electrolyte material design can mitigate some of these issues by different electrolyte additives and enhance the metal electrode's performance. For alkaline conditions, the additives used can be ZnO and polyethylene or ZnO and carboxymethyl cellulose (CMC), as shown in Figure 9. Meanwhile, the additives for neutral salt water solution are Zn 2+ , In 3+ and Sn 3+ . Additionally, some aromatic carboxylic acids are useful in alkaline solutions and have similar effects under acidic conditions. The imidazole group N atoms can be used in acidic solutions [75,91].

Non-Aqueous Electrolyte
Solid-state electrolytes have the potential to minimize electrolyte leakage while maintaining thermal stability and robustness. They also have the potential to eliminate the problems of electrolyte evaporation and gas crossover. Another advantage is that it allows the increase in the energy density of MABs and the creation of reusable and bendable gadgets. Nevertheless, it has the potential to raise the battery's resistance and decrease its capacity. For MABs, the solid-based electrolyte has higher OH interfacial transporting resistance than aqueous system due to the poor wetting property that restricts the threephase interface reaction, but using alkaline gel electrolyte (AGE) could mitigate these issues [16,75,91]. The ionic liquid electrolyte has two types of cations: (1) ions of alkali metal in an organic solvent and (2) large organic cations with inorganic/organic anions. This type of electrolyte has challenges due to carbonate formation that blocks the electrode pores and consumes the electrolyte [16]. Ionic liquids have low volatility, no flammability, and high ionic conductivity. Additionally, they can resist moisture in LABs. Ionic liquids that can

Non-Aqueous Electrolyte
Solid-state electrolytes have the potential to minimize electrolyte leakage while maintaining thermal stability and robustness. They also have the potential to eliminate the problems of electrolyte evaporation and gas crossover. Another advantage is that it allows the increase in the energy density of MABs and the creation of reusable and bendable gadgets. Nevertheless, it has the potential to raise the battery's resistance and decrease its capacity. For MABs, the solid-based electrolyte has higher OH − interfacial transporting resistance than aqueous system due to the poor wetting property that restricts the three-phase interface reaction, but using alkaline gel electrolyte (AGE) could mitigate these issues [16,75,91].
The ionic liquid electrolyte has two types of cations: (1) ions of alkali metal in an organic solvent and (2) large organic cations with inorganic/organic anions. This type of electrolyte has challenges due to carbonate formation that blocks the electrode pores and consumes the electrolyte [16]. Ionic liquids have low volatility, no flammability, and high ionic conductivity. Additionally, they can resist moisture in LABs. Ionic liquids that can be stored at room temperature (RTILs) are a kind of salt that has a melting point of less than 100 • C and is composed of large organic cations and organic/inorganic anions other things. Since MAB electrolytes may be very conductive, exceedingly nonvolatile, and can support the electrochemistry of certain metals, researchers have turned their attention to RTILs as MAB electrolytes as a result of the drying out problem [75,92]. RTILs are also expensive. The aprotic organic electrolyte is broadly used in MABs with metal electrodes that are unstable in water, such as Na and Li [75]. This contributes to the formation of a solid electrolyte interphase (SEI) at the surface of the anode. However, it has concerns for flammability, environmental, toxicity, and economic impacts. Additionally, an organic electrolyte results in a discharge product with nonconductive and insoluble properties that deposit and block the air cathode pores. A mixed electrolyte system has been proposed to solve the issues of cost, undecomposed discharge products, and poor efficiency of the round trip with organic electrolytes, all of which have been addressed [93].

Hybrid Electrolyte
A mixed electrolyte is also referred to as a hybrid electrolyte in certain circles. The name implies that it is composed of two distinct electrolytes separated by a solid electrolyte barrier that prevents water and gas diffusion while transferring cations. NASICON is one example of a solid electrolyte membrane, where it refers to sodium super ionic conductor [93]. The anode electrolyte in a hybrid battery system is called an anolyte, while the cathode electrolyte is called a catholyte. Using an alkali metallic ion (Na + or Li + ) solid-state electrolyte (SSE) separator, a novel aqueous iron-air battery was developed, including alkaline anolyte and acidic catholyte. When the anode and cathode are exposed to oxidation-reduction processes (redox reactions), the alkali metallic ion acts as a mediator of ionic transport [16,94]. Another example of a hybrid electrolyte battery system is the hybrid Na-air cell, which uses both organic and aqueous electrolytes, with a membrane separating them. Figure 10 shows the schematic diagrams for each cell compared to non-aqueous Na-O 2 batteries, with the comparative findings given in Table 8 [93]. state electrolyte (SSE) separator, a novel aqueous iron-air battery was developed, including alkaline anolyte and acidic catholyte. When the anode and cathode are exposed to oxidation-reduction processes (redox reactions), the alkali metallic ion acts as a mediator of ionic transport [16,94]. Another example of a hybrid electrolyte battery system is the hybrid Na-air cell, which uses both organic and aqueous electrolytes, with a membrane separating them. Figure 10 shows the schematic diagrams for each cell compared to nonaqueous Na-O2 batteries, with the comparative findings given in Table 8 [93]. Figure 10. A diagrammatic representation of (a) non-aqueous Na-O battery (b) hybrid Na-air battery, adapted from [93]. In most cases, electrolytes are selected via a trial-and-error procedure based on rules of thumb connecting various characteristics of the electrolyte; as a result, time is spent in testing with different electrolytes to obtain the desired performance. In non-aqueous Li- Figure 10. A diagrammatic representation of (a) non-aqueous Na-O 2 battery (b) hybrid Na-air battery, adapted from [93].

Selecting the Electrolyte
In most cases, electrolytes are selected via a trial-and-error procedure based on rules of thumb connecting various characteristics of the electrolyte; as a result, time is spent in testing with different electrolytes to obtain the desired performance. In non-aqueous Li-O 2 , Na-O 2 , and K-O 2 cells, a connection was found between the solvent reorganization energy and the ORR rate constant k and the oxygen diffusion coefficient D (O 2 ), as shown in Figure 11. The research demonstrates the basic correlations that exist in the membrane between the solvent and the salt and the impact that these interactions have on the overall performance of the battery. With increasing cation size, it has been discovered that the rate of ORR in the presence of alkali metal ions is strongly dependent on the selection of salt anion as the size of the cation grows. For non-aqueous alkali metal-air batteries [95,96], the choosing of the electrolyte is made more accessible by using the graph shown below. O2, Na-O2, and K-O2 cells, a connection was found between the solvent reorganization energy and the ORR rate constant k and the oxygen diffusion coefficient D (O2), as shown in Figure 11. The research demonstrates the basic correlations that exist in the membrane between the solvent and the salt and the impact that these interactions have on the overall performance of the battery. With increasing cation size, it has been discovered that the rate of ORR in the presence of alkali metal ions is strongly dependent on the selection of salt anion as the size of the cation grows. For non-aqueous alkali metal-air batteries [95,96], the choosing of the electrolyte is made more accessible by using the graph shown below. Due to the fact that different kinds of MABs function differently, each type of electrolyte has benefits and drawbacks to consider. On the other hand, Table 9 highlights the benefits and drawbacks associated with each kind of MAB electrolyte.

Cathode of Metal-Air Batteries MABs
The cathode is the third part of MABs, and the active material for the cathode is oxygen from the surrounding environment, which is both free as well as plentiful. Further- Figure 11. Correlation graph between solvent reorganization energy λ, the diffusion coefficient of oxygen D O2, and the ORR rate constant k, adapted from [95,96]. Due to the fact that different kinds of MABs function differently, each type of electrolyte has benefits and drawbacks to consider. On the other hand, Table 9 highlights the benefits and drawbacks associated with each kind of MAB electrolyte. Higher ionic conduction. ZAB has excellent performance at low temperatures. The solubility of zinc salts is very high. CO 2 sensitivity is a concern.
Alkaline solutions are harmful to the environment.
Dissolution of Zn, precipitation of insoluble CO 3 2− hydrogen evolution, and electrolyte evaporation. [ Increased resistance of the battery will result in a reduction in battery capacity. The wetting property is poor. [16,75,91] Hybrid Alkaline anolyte and acidic catholyte. Higher performance. Cycling stability is excellent.

Cathode of Metal-Air Batteries MABs
The cathode is the third part of MABs, and the active material for the cathode is oxygen from the surrounding environment, which is both free as well as plentiful. Furthermore, it does not require a hefty shell to keep it contained, which increases the device's energy density [97,98]. The oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) are the cathode reactions, with ORR occurring during the discharge cycle and OER occurring during the charge cycle [16,99].

Air Cathode Components
The air cathode is made up of a gas diffusion layer (GDL), a catalyst, and a current collector, as displayed in Figure 12. It can affect the properties of MABs greatly, so it must The gas diffusion layer (GDL) performs a variety of tasks. It acts as a conduit between the air atmosphere and the catalyst layer, allowing oxygen to diffuse into the atmosphere, or in other words, it absorbs air from the surrounding environment. Additionally, it inhibits electrolyte leaking out of the battery, stops water from entering into the battery, and it supports the catalyst layer of the battery. GDL should have the following characteristics: hydrophobicity, lightness, thinness, and high porosity. This necessitates meticulous planning ahead of time. Gas diffusion layers are often composed of carbon or catalytic materials and hydrophobic binders such as polytetrafluoroethylene PTFE (Teflon), while the catalytic materials are frequently combined with the binders before being put or imprinted onto current collectors [91].
The catalyst layer is the third component that has a significant effect on the characteristics of MABs. The bifunctional catalyst is required to increase the OER and ORR reactions, because the natural kinetics of the oxygen reactions is typically sluggish and increasing the kinetics of these reactions improves the electrochemical performance of MABs while simultaneously reducing overpotentials. The electrocatalysts may be divided into four categories, which are as follows: noble metals and their alloys, such as platinum Pt, iridium Ir oxides, and ruthenium Ru oxides, showing excellent performance in both OER and ORR tests; (2) metal oxides that are single, binary, or ternary in nature (e.g., MnO, NiO, and CoO); (3) carbonaceous materials, such as doped carbons and nanostructured carbons (e.g., nitrogen doping carbon); and (4) transition metals and metal macrocyclic complexes [28,37,49,50,91,99,100], respectively.

Oxygen Electrochemical Reactions in MABs
Since oxygen acts uniquely in aqueous as well as nonaqueous electrolytes (reaction pathways are shown in Table 10), it was necessary to develop a variety of catalysts that corresponded to distinct reaction processes. Both processes may occur on an air cathode electrode without the use of catalysts; however, since the natural kinetics of oxygen are sluggish, the use of electrocatalysts can speed up the reactions. The oxygen reduction reaction ORR and the oxygen evolution reaction OER are the two processes that occur when oxygen is present. This happens during the discharge process in MABs and consists of The current collector's primary tasks are connecting to external electrical circuits to create a closed circuit and transmit electrons between them. It may be made of non-metal or metal, with the metal current collector being made of porous foam-like metals such as Ni mesh, Cu, and stainless steel. Non-metal current collectors, such as carbon cloth, conductive carbon paper, and graphitic fiber, on the other hand, are made of carbon-based materials [16,91].
The gas diffusion layer (GDL) performs a variety of tasks. It acts as a conduit between the air atmosphere and the catalyst layer, allowing oxygen to diffuse into the atmosphere, or in other words, it absorbs air from the surrounding environment. Additionally, it inhibits electrolyte leaking out of the battery, stops water from entering into the battery, and it supports the catalyst layer of the battery. GDL should have the following characteristics: hydrophobicity, lightness, thinness, and high porosity. This necessitates meticulous planning ahead of time. Gas diffusion layers are often composed of carbon or catalytic materials and hydrophobic binders such as polytetrafluoroethylene PTFE (Teflon), while the catalytic materials are frequently combined with the binders before being put or imprinted onto current collectors [91].
The catalyst layer is the third component that has a significant effect on the characteristics of MABs. The bifunctional catalyst is required to increase the OER and ORR reactions, because the natural kinetics of the oxygen reactions is typically sluggish and increasing the kinetics of these reactions improves the electrochemical performance of MABs while simultaneously reducing overpotentials. The electrocatalysts may be divided into four categories, which are as follows: noble metals and their alloys, such as platinum Pt, iridium Ir oxides, and ruthenium Ru oxides, showing excellent performance in both OER and ORR tests; (2) metal oxides that are single, binary, or ternary in nature (e.g., MnO, NiO, and CoO); (3) carbonaceous materials, such as doped carbons and nanostructured carbons (e.g., nitrogen doping carbon); and (4) transition metals and metal macrocyclic complexes [28,37,49,50,91,99,100], respectively.

Oxygen Electrochemical Reactions in MABs
Since oxygen acts uniquely in aqueous as well as nonaqueous electrolytes (reaction pathways are shown in Table 10), it was necessary to develop a variety of catalysts that corresponded to distinct reaction processes. Both processes may occur on an air cathode electrode without the use of catalysts; however, since the natural kinetics of oxygen are sluggish, the use of electrocatalysts can speed up the reactions. The oxygen reduction reaction ORR and the oxygen evolution reaction OER are the two processes that occur when oxygen is present. This happens during the discharge process in MABs and consists of many stages, the most important of which are as follows: (1) oxygen diffuses into the surface of the catalyst from the surrounding environment. (2) Secondly, the surface of the catalyst absorbs oxygen. (3) The electrons from the anode are transferred to the oxygen molecules through an external circuit. (4) The oxygen connection is broken, and the oxygen bond becomes weaker. (5) The hydroxyl ion product is removed from the catalyst's surface and transferred to the electrolyte. All of these processes are reversible in OER, which happens during the charging process. Because of the relative stability of the intermediates generated following oxygen adsorption on the catalyst, either a four-step or a two-step route may be used in the ORR and OER processes, respectively. The superoxide intermediate produced by the two-electron mechanism is a reactive oxygen species.
Nonaqueous MABs e.g., LAB in nonaqueous electrolyte * is the active site on the surface, (l) is a liquid phase and (g) is a gas phase, O * , OH * and OOH * are adsorbed intermediates.
The hydroxide OH − produced in the four-electron process in an alkaline medium is presented in Equation (16). The process of four electrons is highly required for high power and energy densities. Feeding purified air or employing an O 2 -permeable membrane is necessary for alkaline media to avoid accumulating carbonate ions in the liquid electrolyte with time [100-102].

Progress Done in the Cathode of MAB
Although they have excellent performance, the electrocatalytic activity of noble metalbased electrocatalysts is limited by their poor durability and high cost [5,103,104]. In order to overcome these limitations, a study developed a graphene quantum dot/graphene hydrogel GH-GQD that has good durability and excellent electrocatalytic activity in alkaline solution in primary ZABs. Compared to GO and GH, the GQD exhibits a greater number of active sites, resulting in greater ORR electrocatalytic activity. Then, different concentrations of GQD (45 mg, 90 mg, and 180 mg GQD) were compared, and it was discovered that the GH-GQD-90 exhibited high ORR activity and excellent durability in alkaline primary MABs, high performance as an ORR catalyst in primary ZAB, and its discharge property performance at higher current densities can be compared with Pt/C. When used in MABs and fuel cells, the GH-GQD demonstrates tremendous promise for ORR as an alternative to noble materials [105].
An investigation into rechargeable MABs produced a one-dimensional manganesecobalt oxide (spinel-type), Mn Co 2 O 4 (MCO), and CoMn 2 O 4 (CMO) nanofiber, as shown in Figure 13, that served as bi-functional cathode catalysts for the devices. As shown in Figure 14, these both have a high catalytic activity for both ORR and OER in an alkaline solution. Then, they were tested in ZABs as catalysts and were shown to decrease the gaps between the discharge and charge voltages significantly. As a result, the round-trip efficiency was improved as compared to a cathode without a catalyst. Despite repeated discharge-charge cycling, the CMO-NF, and MCO-NF catalysts maintain their stability; however, carbon corrosion in the catalyst/carbon composite cathode caused the battery's cycling performance to degrade significantly. A comparison of the electrochemical performance of ZABs utilizing the nanofiber catalysts that were manufactured with the performance of Pt/C and catalyst-free carbon cathodes is shown in Figure 15 [106]. It is possible that the structure of MCO-NF and OMC-NF, which facilitate mass movement via the porous one-dimensional structure and provide a high number of active reaction sites, is responsible for the enhancement of the electrochemical properties.      To obtain Pt-based alternative electrocatalysts, a study mixed Ni, Co, and S to obtain a better electrochemical performance. Mixing sulfides and metal oxides containing transition metals frequently showed useful electrochemical efficiency due to transition metal elements' synergy with single sulfide or metal oxide. NiCo 2 S 4 hollow microspheres resemble a hydrangea and have a highly porous structure. The porous structure of NiCo 2 S 4 may aid in the diffusion of oxygen and hydroxyl reactants, and it often has a high surface area for oxygen reactions due to its porous nature. When NiCo 2 S 4 microspheres are tested in an alkaline medium, they exhibit good electrocatalytic activity for OER and ORR and high stability, making them a suitable catalyst for aqueous AABs and rechargeable ZABs. Moreover, the hydrangea-like structure exhibits numerously desorbed and adsorbed sites for oxygen. Therefore, NiCo 2 S 4 microspheres can be evaluated for aqueous MABs as an advanced electrocatalyst [107].
In another study, a PdCo/C bimetallic nanocatalyst was prepared as a potential air cathode catalyst. The prepared catalysts went through a heat treatment process at 200 • C in H 2 /Ar atmosphere from 4 to 24 h and the image for each period is presented in Figure 16. A clear correlation was found between the heat treatment and the total catalyst performance. The optimum heat treatment duration was 8 h, resulting in the greatest activity for ORR and OER. As a consequence, the HT-8 h PdCo/C catalyst was tested in rechargeable Zn-air and Mg-air batteries. The resulting performance of each battery is shown in Figures 17 and 18, respectively, to demonstrate its effectiveness. When the HT-8 h PdCo/C catalyst is used, the stability and activity of the Zn-air and Mg-air batteries are improved, and the activity is increased, indicating that it has the potential to be used on a broad scale [108].   and internal electrical resistance of the system are both reduced, allowing for an increase in water transportation to reaction sites as well as an increase in air permeability. As demonstrated in Figure 21, the performance of the magnesium-air single cell utilizing manufactured air cathodes is comparable to that of a commercial air cathode [109]. The newly designed air cathode, on the other hand, is both cost-effective in terms of production and materials and appropriate as a cathode for an MAB in a neutral or alkaline electrolyte.   A novel technique for manufacturing air cathodes is described in Figure 19, which employs cost-effective ways to reduce the cathode structure while maintaining high quality. The effect of temperature on the manufactured in-house air cathode can be seen in the polarization curves shown in Figure 20A and Table 11, respectively. The research team utilized various characterization methods to further understand the performance and characteristics of the newly created air cathode, which was then compared to commercial air cathodes for comparison. Since the developed air cathode does not require the heat seal coating materials that are used in the commercial air cathode, the gas flow restriction and internal electrical resistance of the system are both reduced, allowing for an increase in water transportation to reaction sites as well as an increase in air permeability. As demonstrated in Figure 21, the performance of the magnesium-air single cell utilizing manufactured air cathodes is comparable to that of a commercial air cathode [109]. The newly designed air cathode, on the other hand, is both cost-effective in terms of production and materials and appropriate as a cathode for an MAB in a neutral or alkaline electrolyte.     Table 11), adapted from [109].  Table 11), adapted from [109].   The non-aqueous LAB was used to investigate the effect of the operating temperature on the morphology of the discharge product produced. The solid discharge product Li2O2 clogs the cathode pores, thus stopping the discharge process. The product must be oxidized before it can be used in the charging process. Following the application of various operating temperatures at varying discharge current densities, the morphology of the Li2O2 discharge product and the performance are shown in Figures 22 and 23, respectively, after the application of different operating temperatures.
This is in addition to Figure 24, which depicts the voltage-capacitance graphs at various temperatures. It is concluded that altering the operating temperature at a certain discharge current density does not affect the form of Li2O2, while raising the operating temperature causes a reduction in the size of the discharge product. Additionally, the form of the discharge product at a given temperature change in relation to the discharge current density. Finally, the operating temperature impacts the charge voltage, cyclability, and capacity of a particular non-aqueous LAB [110]. The non-aqueous LAB was used to investigate the effect of the operating temperature on the morphology of the discharge product produced. The solid discharge product Li 2 O 2 clogs the cathode pores, thus stopping the discharge process. The product must be oxidized before it can be used in the charging process. Following the application of various operating temperatures at varying discharge current densities, the morphology of the Li 2 O 2 discharge product and the performance are shown in Figures 22 and 23, respectively, after the application of different operating temperatures.    This is in addition to Figure 24, which depicts the voltage-capacitance graphs at various temperatures. It is concluded that altering the operating temperature at a certain discharge current density does not affect the form of Li 2 O 2 , while raising the operating temperature causes a reduction in the size of the discharge product. Additionally, the form of the discharge product at a given temperature change in relation to the discharge current density. Finally, the operating temperature impacts the charge voltage, cyclability, and capacity of a particular non-aqueous LAB [110].

Progress in the Design of the MABs
The two kinds of MABs are primary and secondary, as highlighted in Figure 25a-c. Primary MABs are non-rechargeable, while secondary MABs are rechargeable. The main MABs have two electrodes, each with an ORR catalyst, while the rechargeable MABs have two or three electrodes, each with an ORR and OER catalyst, depending on the model. In the three-electrode arrangement, the metal electrode is located between the air cathode electrode and the charging electrode for the OER, which is a convenient position. The air cathode is electrically separated during the charging process, which extends its lifespan by preventing it from being exposed to the high oxygen evolution reaction potential during the charging phase. In contrast, the two-electrode design of rechargeable MABs, shown in Figure 25c, consists of a metal electrode and a bifunctional air electrode that contains catalysts for ORR and OER, as well as other functions. This arrangement is straightforward and does not need the separation of the two electrolyte flows, since the air cathode may serve as both an anode for OER and a cathode for ORR [99]. Furthermore, it has less mass (resulting in higher specific energy) and fewer interfaces, which reduces the possibility of kinetic rate losses. Additionally, recent research has focused on improving the stability and efficiency of bifunctional catalysts [111].

Progress in the Design of the MABs
The two kinds of MABs are primary and secondary, as highlighted in Figure 2 Primary MABs are non-rechargeable, while secondary MABs are rechargeable. The MABs have two electrodes, each with an ORR catalyst, while the rechargeable MABs two or three electrodes, each with an ORR and OER catalyst, depending on the mod the three-electrode arrangement, the metal electrode is located between the air cat electrode and the charging electrode for the OER, which is a convenient position. Th cathode is electrically separated during the charging process, which extends its life by preventing it from being exposed to the high oxygen evolution reaction potential ing the charging phase. In contrast, the two-electrode design of rechargeable M shown in Figure 25c, consists of a metal electrode and a bifunctional air electrode contains catalysts for ORR and OER, as well as other functions. This arrangeme straightforward and does not need the separation of the two electrolyte flows, sinc air cathode may serve as both an anode for OER and a cathode for ORR [99]. Furtherm it has less mass (resulting in higher specific energy) and fewer interfaces, which red the possibility of kinetic rate losses. Additionally, recent research has focused on imp ing the stability and efficiency of bifunctional catalysts [111].  Figure 26 illustrates the classification of MABs into three configurations: the con tional static battery, the flow battery, and the flexible battery. The first configuration i traditional static air battery, which consists of the three primary components (anode, ode, and electrolyte) and a separator. In this configuration, the kinetics of the anode tion are fast compared with the cathode reaction, and it requires highly efficient cata to facilitate the reactions, in addition to the challenge of the by-products that depos solubly on the surface of the electrodes during charge-discharge cycles, resulting in crease in the battery's performance due to the blocking of the pores of the electrode  Figure 26 illustrates the classification of MABs into three configurations: the conventional static battery, the flow battery, and the flexible battery. The first configuration is the traditional static air battery, which consists of the three primary components (anode, cathode, and electrolyte) and a separator. In this configuration, the kinetics of the anode reaction are fast compared with the cathode reaction, and it requires highly efficient catalysts to facilitate the reactions, in addition to the challenge of the by-products that deposit insolubly on the surface of the electrodes during charge-discharge cycles, resulting in a decrease in the battery's performance due to the blocking of the pores of the electrode, limiting the air diffusion step. The second configuration is the flow battery, which consists of an anode, cathode, electrolyte, separator, and electrolyte bank, and to drive the electrolyte flow, it is usually installed with a pump. The configuration of the electrolyte flow decreased the volume density and energy efficiency; also, additional tubes and pumps increased complications during the discharge process. The third configuration is the flexible battery, which is of huge interest due to the increasing demand for flexible, portable electronics in recent years which require a flexible energy storage device. This type of battery consists of a thin metallic plate anode to reduce battery weight, a cathode such as carbon fiber, a highly conductive electrolyte, and a separator. Currently, the ideal flexible batteries are ZABs and aluminum-air batteries, due to their safe operation, high energy density, and low cost [16].

Static MABs
In addition to tiny and portable electronic gadgets, the static system may also be used for large-scale electronics. Metal-air batteries with a static structure have been extensively researched; however, their performance is restricted regarding practical power/energy density and energy efficiency, respectively. The integration of static cell structure with other energy technologies, on the other hand, is complicated and difficult [112].

Parallel-Plate Electrode Configuration
The arrangement of the parallel-plate electrode configuration shown in Figure 27 allows high heat dissipation and mass transport rates. For laboratories, small cells are favored due to the low requirements of power and volume. However, the heat generated in large cells during the charge and discharge cycles has to be considered. The cross-section of a unit cell and the stack connecting several cells together to form a battery are displayed in Figure 28 [51]. Several materials are investigated in air cathodes such as Pt/C combined with Ir/C, and urchin-like NiO S microspheres covered by a sulfur-doped graphene nanosheet, S-GNS (S-GNS/ NiO S ) [113].

Static MABs
In addition to tiny and portable electronic gadgets, the static system may also be used for large-scale electronics. Metal-air batteries with a static structure have been extensively researched; however, their performance is restricted regarding practical power/energy density and energy efficiency, respectively. The integration of static cell structure with other energy technologies, on the other hand, is complicated and difficult [112].

Parallel-Plate Electrode Configuration
The arrangement of the parallel-plate electrode configuration shown in Figure 27 allows high heat dissipation and mass transport rates. For laboratories, small cells are favored due to the low requirements of power and volume. However, the heat generated in large cells during the charge and discharge cycles has to be considered. The cross-section of a unit cell and the stack connecting several cells together to form a battery are displayed in Figure 28 [51]. Several materials are investigated in air cathodes such as Pt/C combined with Ir/C, and urchin-like NiO 2 S 4 microspheres covered by a sulfur-doped graphene nanosheet, S-GNS (S-GNS/NiO 2 S 4 ) [113].

Coin-Type
A coin cell type and its components are shown in Figure 29, and Figure 30 displays the performance of this configuration using different electrolytes at 6 M concentration: potassium hydroxide (KOH), poly vinyl alcohol (PVA), poly acrylic acid (PAA), and PAM [114].

Coin-Type
A coin cell type and its components are shown in Figure 29, and Figure 30 displays the performance of this configuration using different electrolytes at 6 M concentration: potassium hydroxide (KOH), poly vinyl alcohol (PVA), poly acrylic acid (PAA), and PAM [114].

Coin-Type
A coin cell type and its components are shown in Figure 29, and Figure 30 displays the performance of this configuration using different electrolytes at 6 M concentration: potassium hydroxide (KOH), poly vinyl alcohol (PVA), poly acrylic acid (PAA), and PAM [114].

In Situ Cell
Numbered components of an in situ cell are shown in Figure 31. The alloy clamp rings and PEEK screws, used to close the cell after assembly, are numbered 1 and 2, respectively. The thin sheets of Ni metal (used as negative and positive electrodes) are numbered 3 and 4, respectively. The tubing connections for pumping the electrolyte or gas fuel are numbered 5. The thyristor is numbered 6.

In Situ Cell
Numbered components of an in situ cell are shown in Figure 31. The alloy clamp rings and PEEK screws, used to close the cell after assembly, are numbered 1 and 2, respectively. The thin sheets of Ni metal (used as negative and positive electrodes) are numbered 3 and 4, respectively. The tubing connections for pumping the electrolyte or gas fuel are numbered 5. The thyristor is numbered 6. Figure 29. Schematic diagram of a coin cell, with permission to reproduce from [114].

In Situ Cell
Numbered components of an in situ cell are shown in Figure 31. The alloy clamp rings and PEEK screws, used to close the cell after assembly, are numbered 1 and 2, respectively. The thin sheets of Ni metal (used as negative and positive electrodes) are numbered 3 and 4, respectively. The tubing connections for pumping the electrolyte or gas fuel are numbered 5. The thyristor is numbered 6.

Flexible MABs
The stability of the flexible MABs should be ensured when subjected to frequent mechanical strain over an extended time period, and the security of the battery should be ensured when subjected to a variety of deformation circumstances. The electrodes in flexible MABs must have the ability to adapt to changing conditions. Metal ribbons, metal rods, metal foil, or a flexible metal substrate covered with a metallic powder may be used

Flexible MABs
The stability of the flexible MABs should be ensured when subjected to frequent mechanical strain over an extended time period, and the security of the battery should be ensured when subjected to a variety of deformation circumstances. The electrodes in flexible MABs must have the ability to adapt to changing conditions. Metal ribbons, metal rods, metal foil, or a flexible metal substrate covered with a metallic powder may be used as anodes, as can metal rods coated with a metallic powder. Additional characteristics of a cathode current collector include great flexibility, high conductivity, and air permeability. These characteristics should be combined with an active material coating to produce a flexible air cathode. The carbon materials with the greatest potential as active materials are graphene and nanotubes, which are distinguished by their high tensile strength and high Young's modulus. As a bonus, putting metallic or metal oxide/nitride on a carbon substrate enhances the cathode's catalytic activity [16]. The remarkable performance of the flexible MABs is attributed to the close contact that exists between the cell components [116].

Fiber-Type
The configuration of this type of flexible MAB and the progress made in its development are shown in Figure 32. The cell structure of this type of MAB is usually a polymer electrolyte (e.g., gelatin gel polymer electrolyte GGPE) around the central metal anode and flexible air cathode coated with the electrolyte. It can operate efficiently under external strain. Additionally, other studies demonstrated the excellent mechanical stability and electrochemical performance of this configuration type [116].

Sandwich-Type
The components in sandwich-type MAN are produced in plan form, then assembled as in Figure 33. This configuration exhibited high volumetric and gravimetric energy density and excellent electrochemical and cycling performance under bending conditions even at a high current density [116,118].

Sandwich-Type
The components in sandwich-type MAN are produced in plan form, then assembled as in Figure 33. This configuration exhibited high volumetric and gravimetric energy density and excellent electrochemical and cycling performance under bending conditions even at a high current density [116,118]. Array A planner multilayer MAB array configuration is presented in Figure 34. It possesses flexible and stretchable properties, a thickness of nearly 3 mm, and exhibits excellent stable and rechargeable battery performance. This array can be connected in series and parallel, or in a combination between them. It can be used in wearable devices [69].

Sandwich-Type
The components in sandwich-type MAN are produced in plan form, then assembled as in Figure 33. This configuration exhibited high volumetric and gravimetric energy density and excellent electrochemical and cycling performance under bending conditions even at a high current density [116,118]. Array A planner multilayer MAB array configuration is presented in Figure 34. It possesses flexible and stretchable properties, a thickness of nearly 3 mm, and exhibits excellent stable and rechargeable battery performance. This array can be connected in series and parallel, or in a combination between them. It can be used in wearable devices [69].

Flow MABs (MAFBs)
The flow system is adaptable and can be readily combined with different energy technologies when it comes to cell construction. It is safe and has a long operational life because of the flow of the anolyte/electrolyte, minimizing side reactions. It has the potential to be used for large-scale energy storage as well as stationary power plants. The anolyte circulation is, however, depicted in Figure 35 [120].

Flow MABs (MAFBs)
The flow system is adaptable and can be readily combined with different energy technologies when it comes to cell construction. It is safe and has a long operational life because of the flow of the anolyte/electrolyte, minimizing side reactions. It has the potential to be used for large-scale energy storage as well as stationary power plants. The anolyte circulation is, however, depicted in Figure 35 [120].

Flow MABs (MAFBs)
The flow system is adaptable and can be readily combined with different energy technologies when it comes to cell construction. It is safe and has a long operational life because of the flow of the anolyte/electrolyte, minimizing side reactions. It has the potential to be used for large-scale energy storage as well as stationary power plants. The anolyte circulation is, however, depicted in Figure 35 [120].

Anolyte Circulation
The system consists of an anode electrode, an ion transport membrane, catalysts, a casting air electrode, and two current collectors. The cell in Figure 35 uses a flow of a redox couple at the negative electrode, while it uses air or oxygen at the positive electrode. The flow rate of the anolyte must be controlled to avoid any possible concentration polarization. Replacing the positive electrolyte tank that used conventional redox flow batteries REBs with an oxygen GDE reduces the volume and total weight, thus improving the

Anolyte Circulation
The system consists of an anode electrode, an ion transport membrane, catalysts, a casting air electrode, and two current collectors. The cell in Figure 35 uses a flow of a redox couple at the negative electrode, while it uses air or oxygen at the positive electrode. The flow rate of the anolyte must be controlled to avoid any possible concentration polarization. Replacing the positive electrolyte tank that used conventional redox flow batteries REBs with an oxygen GDE reduces the volume and total weight, thus improving the power and energy densities. Vanadium-air and zinc-air flow batteries (VAFB, ZAFB) are an example of this approach towards metal-air flow batteries [112,120].

Electrolyte Cycling
This approach is presented in Figure 36A, where the fresh electrolyte continuously supplies the flow through the electrochemical cell. It increases the metal anode charge and discharges efficiency, and at the same time, it eliminates the by-products and the side reactions. Therefore, the cathode becomes less blocked, which is favorable for oxygen access. Sodium-air, zinc-air as well as lithium-air flow batteries can be fabricated using this approach, and Figure 36B shows the efficiency of zinc-air flow batteries using a NiS x -FeO y /sulfur-doped carbon fiber paper SCFP catalyst [112].  [112,120].

Electrolyte Cycling
This approach is presented in Figure 36A, where the fresh electrolyte continuously supplies the flow through the electrochemical cell. It increases the metal anode charge and discharges efficiency, and at the same time, it eliminates the by-products and the side reactions. Therefore, the cathode becomes less blocked, which is favorable for oxygen access. Sodium-air, zinc-air as well as lithium-air flow batteries can be fabricated using this approach, and Figure 36B shows the efficiency of zinc-air flow batteries using a NiS -FeO /sulfur-doped carbon fiber paper SCFP catalyst [112].

Hybrid Electrolyte Flow Battery
Since some metals, such as Na and Li, are water-sensitive, and thus their use is questionable in aqueous media. Inorganic/organic hybrid electrolytes separated by a plate that is a superionic conductor are suggested in their flow configurations. Additionally, this

Hybrid Electrolyte Flow Battery
Since some metals, such as Na and Li, are water-sensitive, and thus their use is questionable in aqueous media. Inorganic/organic hybrid electrolytes separated by a plate that is a superionic conductor are suggested in their flow configurations. Additionally, this concept has been widely improved in static sodium and lithium-air batteries to protect the aprotic electrolyte and protect the highly reactive the Na/Li metal anode from oxygen crossover or water and carbon dioxide impurities in ambient air [112].

Bidirectional Flow Battery with a Two-Layered Cathode
The bidirectional flow battery components of vanadium-air flow battery (VAFB) are shown in Figure 37, where it used an exchangeable gas diffusion electrode with a different catalyst for both charging and discharging processes. Involving this developed cathode in VAFB resulted in 44.5% voltaic efficiency and 87.6% coulombic at 40 mA cm −2 (used catalyst Pt/C and IrO 2 ), but highly active electrocatalysts and crossover-minimizing membranes need to be collectively improved [112]. For example, in a vanadium redox flow battery, the crossover of vanadium species through the ion-exchange membrane (IEM) is a serious problem that leads to continuous capacity decay. To decrease this problem, tungsten oxide nanofiller with different mass loadings (0-20 wt.%) was introduced in the Nafion matrix [122]. The lowest vanadium species crossover was achieved using 20% wt. of WO 3 . The coulombic efficiency, energy efficiency, and capacity retention were enhanced by 93%, 75% and 62%, respectively, as compared to 88%, 65%, and 42%, respectively, in the case of using pristine Nafion 212. Additionally, the electrode materials and their cost have a great effect on the development and commercialization of flow batteries. For instance, in addition to the selection of mechanically and thermally stable electrodes, the cathode structure should be porous to facilitate the ORR reaction [123]. Additionally, the polarization effect is important, and the pretreatment of electrodes is essential to improve the electrodes' surface area and/or hydrophilicity. The treatment of graphite felt with polyacrylonitrile (PAN-GF) or rayon (R-GF) was performed to study the effect of a precursor on the polarization effect [124]. The PAN-GF has higher conductivity due to the higher degree of graphitization, and thus more negligible ohmic polarization. Meanwhile, R-GF achieved better mass transfer and diffusion of the electrolyte on the electrode surface due to its more significant surface roughness. the polarization effect is important, and the pretreatment of electrodes is essential to improve the electrodes' surface area and/or hydrophilicity. The treatment of graphite felt with polyacrylonitrile (PAN-GF) or rayon (R-GF) was performed to study the effect of a precursor on the polarization effect [124]. The PAN-GF has higher conductivity due to the higher degree of graphitization, and thus more negligible ohmic polarization. Meanwhile, R-GF achieved better mass transfer and diffusion of the electrolyte on the electrode surface due to its more significant surface roughness.

Large-Scale Metal-Air Batteries
Nowadays, much concern has been given to global warming resulting from fossil fuels [126,127]. Several methods have been carried out to minimize the reliance on fossil fuels, such as using efficient energy conversion devices such as fuel cells [128][129][130] that are efficient and environmentally friendly [131], improving the efficiency of the current

Large-Scale Metal-Air Batteries
Nowadays, much concern has been given to global warming resulting from fossil fuels [126,127]. Several methods have been carried out to minimize the reliance on fossil fuels, such as using efficient energy conversion devices such as fuel cells [128][129][130] that are efficient and environmentally friendly [131], improving the efficiency of the current energy conversion devices and/or using renewable energy sources [132][133][134][135]. Among these different methods, renewable energy sources are the most promising option, as they are sustainable and have no or low environmental impacts [136][137][138][139]. However, the significant increase in renewable energy requires a proper energy storage system to accommodate such requirements [140,141]. With the increasing prevalence of renewable energy production sources such as wind [142][143][144][145] and solar energy [146][147][148][149], the electricity grid will need the assistance of a large-scale electrical energy storage system. The energy produced from renewable sources is intermittent, aperiodic, and changeable in nature, requiring constant attention. Consequently, storing energy during unexpected energy production periods is essential to maintain the quality of the electricity generated and satisfy the increasing electricity demand. When compared to other systems, electrochemical energy storage systems may meet the primary requirements for large-scale energy storage systems, which include a short life cycle, rapid response time, scalability, and high efficiency [84,112,150]. Electrochemical energy storage systems may also be more cost-effective than other systems. Typically, electrochemical energy storage refers to electrochemical capacitors and rechargeable batteries, which may be used in conjunction with other systems in a hybrid configuration [151,152]. For large-scale energy storage, it is necessary to have a battery with a life of 5000 charge-discharge cycles at energy efficiency of about 80% for the round trip [84].
The airflow sustains the reaction of the air electrode in the MABs, which eliminates the need for tanks to store the reactant. In addition, for the use of large-scale energy storage, the air electrode must be bifunctional for both ORR and OER during discharge and charge, respectively, in order to be effective. Because MABs are cost-effective, ultralightweight, and have a high energy density that is theoretically equal to that of gasoline, they are an excellent alternative to gasoline. In contrast, its energy efficiency is poor, and its charge/discharge life cycle is short. Figure 38 shows that MABs have a good energy density; however, the technology is still in the development stage in terms of efficiency and availability. Still, it has a possible future in the investment deferral application of distributed storage [153], as shown in the figure. It has evolved into an excellent energy storage technology for ecologically friendly and high-performance electric cars, among other applications [107]. Despite this, MABs' large-scale use is limited by their poor energy efficiency and power density, caused by a higher overpotential and slow oxygen reactions at the air cathode.
charge/discharge life cycle is short. Figure 38 shows that MABs have a good energy density; however, the technology is still in the development stage in terms of efficiency and availability. Still, it has a possible future in the investment deferral application of distributed storage [153], as shown in the figure. It has evolved into an excellent energy storage technology for ecologically friendly and high-performance electric cars, among other applications [107]. Despite this, MABs' large-scale use is limited by their poor energy efficiency and power density, caused by a higher overpotential and slow oxygen reactions at the air cathode.  Iron-air batteries are a potential option for large-scale energy storage because of their cheap cost, environmental friendliness, ease of scaling up, long-term viability, and abundance of raw materials, among other characteristics. However, their cycle life and efficiency need to be improved; only then will they be a viable option [150]. Furthermore, aluminum-air batteries (AABs) have the lowest cost and the second greatest specific capacity theoretically, making them a strong prospect for large-scale energy applications in the future among MABs, particularly in renewable energy. As a result, AABs are very appealing as a sustainable and efficient technology for energy storage and conversion, with the capability of providing power for automobiles and large electronic equipment [154]. The high energy density of MABs and redox flow batteries (RFBs), as well as the unique design of their structural components, have both shown significant promise for large-scale electrical energy storage as efficient electrochemical systems. Using a combination of MABs and the idea of flow batteries to overcome side reactions results in a potential candidate for the development of a metal-air flow battery for electrical energy storage in large-scale applications. Metal-air flow technologies, because of their inherent benefits and the high degree of design freedom they provide, have tremendous potential for large-scale energy storage and transmutation in the future power grid. It is also important to note that before contemplating the use of MAB technologies in the commercial sector, efforts should be made to ensure their safety and dependability in the industrial and academic sectors [112]. It is necessary to improve the efficiency and energy density of vanadium-air flow batteries (VAFBs) while also lowering the stack cost to be used on a large scale in commercial applications [112].

Applications of MABs
Metal-air batteries are used in a variety of applications. Metal-air batteries can be used as small power sources for electric cars as well as portable electronic devices. Furthermore, they may be used as energy storage devices or as effective stations of energy transfer, particularly when it comes to renewable energy producers, as they can control the flow of energy from sources such as photovoltaic (PV) panels, wind turbines, and electric grids, among other things.

Wastewater Treatment Using MABs
Besides the main function of MABs in storing energy, they can be used in the treatment of water used in the production of electricity. The studies on MABs in this area are limited or very uncommon. The study on water treatment conducted by MABs may be classified into three categories: the collection of compounds in water, the removal of heavy metals from water, and the treatment of household sewage and wastewater [87].
As a small-scale device, a MAB is simple to set up and run, and it may be used for household sewage as a pretreatment device, where it can decrease COD, total phosphorus, as well as ammonia nitrogen in domestic water to acceptable levels. When employed as a preliminary treatment unit, the high salinity of most industrial wastewater is advantageous as an electrolyte for the MAB's discharge, allowing the device to produce more products of the metal anode and, as a result, the concentration of pollutant may be reduced. At this time, only wastewater from aquaculture has been investigated [87].
Al-air and iron-air batteries from the literature have been utilized to investigate the overall efficiency of electricity production and the treatment effect of wastewater. It was discovered that higher conductivity (higher NaCl concentration) and varying pH values have little effect on the battery discharge. Higher conductivity (higher NaCl concentration) and different pH values have little impact on the battery discharge. Furthermore, it was highlighted that an aluminum-iron double anode exhibited the best battery efficiency [87][88][89].
As shown in Figure 39, an aluminum-air battery (AAB) was coupled with a microbial electrolysis cell MEC to produce hydrogen, clean wastewater, and generate coagulants, all without the need for external energy. Both contribute to energy recovery as a result of this combination. It has been shown that the Al-air battery-MEC system is self-sufficient in terms of energy supply, with an AAB of 28 mL providing 0.58 to 0.8 volts of electricity for an MEC of 28 Ml [89]. all without the need for external energy. Both contribute to energy recovery as a result of this combination. It has been shown that the Al-air battery-MEC system is self-sufficient in terms of energy supply, with an AAB of 28 mL providing 0.58 to 0.8 volts of electricity for an MEC of 28 Ml [89].

Water Desalination Using MABs
Because the process of generating fresh water consumes energy, water desalination necessitates the development of high-performance as well as low-energy technologies. In addition to their capacity to store energy, electrochemical methods hold tremendous prospects for the desalination of water [155][156][157][158]. A metal-air desalination battery (MADB) is a device that can desalinate water while also generating energy. It is self-powered and has

Water Desalination Using MABs
Because the process of generating fresh water consumes energy, water desalination necessitates the development of high-performance as well as low-energy technologies. In addition to their capacity to store energy, electrochemical methods hold tremendous prospects for the desalination of water [155][156][157][158]. A metal-air desalination battery (MADB) is a device that can desalinate water while also generating energy. It is self-powered and has the capability of generating electricity. As shown in Figure 40, the MADB included an AAB that used seawater as both a desalination solution and an electrolyte. The effectiveness of the MADB idea is demonstrated by the desalination performance, stability, and power output that have been achieved. However, the amount of energy produced and the pace of desalination were both restricted by the quantity of dissolved oxygen in the cathode. The highest power density achieved was 2.83 W m −2 at a current density of 6.58 A m −2 and an output voltage of 0.43 V, with the current density being 6.58 A m −2 and the output voltage being 0.43 V. Additionally, it reduces salinity by 37.8 percent while generating 10 mW h of energy for 14 h of operation. Further development of the MADB may make it possible to use this idea in the future in actual applications on a large or small scale [159].

Water Desalination Using MABs
Because the process of generating fresh water consumes energy, water desalination necessitates the development of high-performance as well as low-energy technologies. In addition to their capacity to store energy, electrochemical methods hold tremendous prospects for the desalination of water [155][156][157][158]. A metal-air desalination battery (MADB) is a device that can desalinate water while also generating energy. It is self-powered and has the capability of generating electricity. As shown in Figure 40, the MADB included an AAB that used seawater as both a desalination solution and an electrolyte. The effectiveness of the MADB idea is demonstrated by the desalination performance, stability, and power output that have been achieved. However, the amount of energy produced and the pace of desalination were both restricted by the quantity of dissolved oxygen in the cathode. The highest power density achieved was 2.83 W m −2 at a current density of 6.58 A m −2 and an output voltage of 0.43 V, with the current density being 6.58 A m −2 and the output voltage being 0.43 V. Additionally, it reduces salinity by 37.8 percent while generating 10 mW h of energy for 14 h of operation. Further development of the MADB may make it possible to use this idea in the future in actual applications on a large or small scale [159].  Zinc-air desalination (ZAD) in Figure 41 has been utilized from the literature for electrochemical desalination using MAB technology. The ZAD cell using MoS 2 bifunctional catalyst showed a 0.9 to 1.0 mg NaCl/cm 2 desalination capacity and 70% charge efficiency at a current density of 1 mA/cm 2 . The metal-air desalination MAD is a new technology that provides a highly promising performance for electrochemical desalination based on non-noble metal catalysts [156].
An aluminum-air battery (AAB) was combined with an electrodialysis system. The membrane of the AAB was replaced with the electrodialysis cell to decrease the amount of energy needed for water desalination. The desalination occurs in the middle chamber in a three-chamber system, which is separated by cation and anion exchange membranes (CEM and AEM, respectively) from the side chambers. The anode and cathode electrochemical reactions provide a sufficient driving force: an electro-osmotic drag force for ion diffusion from sea salt water into anode and cathode chambers. The integrated system using an electrolyte of NaOH 5 mM produced an open-circuit voltage of 1.6 V at a current density of 3 mA/cm 2 during one hour of cell operation, the saltwater conductivity decreased from 5 to 4 ms, indicating the decrease in the number of ions in the water. The cell produced 4.8 mW/cm 2 of power. This combined system can work without requiring any power source [160]. A Zn-air battery with N-doped porous carbon (NPC) as an electrocatalyst for ORR was also utilized as a power source for capacitive deionization CDI, which demonstrated excellent desalination performance when NPC was functionalized with sulfuric acid as the CDI cathode material [23,161].
Zinc-air desalination (ZAD) in Figure 41 has been utilized from the literature for electrochemical desalination using MAB technology. The ZAD cell using MoS bifunctional catalyst showed a 0.9 to 1.0 mg NaCl/cm desalination capacity and 70% charge efficiency at a current density of 1 mA/cm . The metal-air desalination MAD is a new technology that provides a highly promising performance for electrochemical desalination based on non-noble metal catalysts [156]. An aluminum-air battery (AAB) was combined with an electrodialysis system. The membrane of the AAB was replaced with the electrodialysis cell to decrease the amount of energy needed for water desalination. The desalination occurs in the middle chamber in a three-chamber system, which is separated by cation and anion exchange membranes (CEM and AEM, respectively) from the side chambers. The anode and cathode electrochemical reactions provide a sufficient driving force: an electro-osmotic drag force for ion diffusion from sea salt water into anode and cathode chambers. The integrated system using an electrolyte of NaOH 5 mM produced an open-circuit voltage of 1.6 V at a current density of 3 mA/cm during one hour of cell operation, the saltwater conductivity decreased from 5 to 4 ms, indicating the decrease in the number of ions in the water. The cell produced 4.8 mW/cm 2 of power. This combined system can work without requiring any power source [160]. A Zn-air battery with N-doped porous carbon (NPC) as an electrocatalyst for ORR was also utilized as a power source for capacitive deionization CDI, which demonstrated excellent desalination performance when NPC was functionalized with sulfuric acid as the CDI cathode material [23,161].

Challenges of MABs
Although the MAB technology has been researched over the last decade, several technical difficulties must be solved before the concept can be commercially implemented.

Metallic Anode Challenges
One of the critical problems facing MABs is the corrosion, passivation, and dendritic formation of the metallic anode. Corrosion is one of the most crucial side reactions between a metal and an electrolyte, as shown by the following process.

Challenges of MABs
Although the MAB technology has been researched over the last decade, several technical difficulties must be solved before the concept can be commercially implemented.

Metallic Anode Challenges
One of the critical problems facing MABs is the corrosion, passivation, and dendritic formation of the metallic anode. Corrosion is one of the most crucial side reactions between a metal and an electrolyte, as shown by the following process.
Hydrogen evolution is naturally favored in nearly all MABs because the standard voltage of M/MO is below the level of hydrogen evolution. The rate of corrosion caused by the hydrogen evolution reaction (HER) may be calculated using the equations above. The HER can decrease the columbic efficiency of a metal anode, which may result in a battery explosion. Corrosion may occur in FABs, AABs, ZABs, and LABs, among other types of batteries. Table 12 illustrates several methods for lowering the HER rate while simultaneously increasing charging efficiency. Table 12. Reducing corrosion strategies [16].

Metal Reducing Corrosion or HER Rate by
ZnO surface Increasing ZnO reduces the self-discharge rate. Al Changing purity, properties, and temperature of the alkaline electrolyte.

Fe
Utilization of ionic membrane. Using an alloy as an anode instead of pure metal and additives such as sulfur or bismuth is a good way to save money.
Passivation is the development of an insulating layer on the electrode surface, which prevents the discharge product from moving around. Electrode discharge is prevented by the layer that develops. This may be found in AABs, ZABs, and LABs batteries, among other things. Depending on the system, the passivation layers in MABs are LiOH, ZnO, and Al 2 O 3, respectively. In the presence of an air cathode, the generated soluble species turned to a non-conductive layer on the surface of the metal. They raise the cell's internal electric resistance, which prevents the dissolving of metal. Using porous electrodes to avoid the development of a passivation layer is an effective approach [16].
Dendritic formation and deformation cause the shape of the metal electrode to gradually change, meaning that the surface roughness becomes uneven as dendrites form. This occurs due to the accumulation of metal ions during metal electrode cycling in alkaline electrolytes. This can result in an unstable battery system, or it may cause a shortcut. Dendritic structures form in Li-air, Fe-air, and Zn-air batteries [16].

Electrolyte Challenges
Dissolving CO 2 from the air in the aqueous KOH electrolyte represents a challenge for some types of MABs, such as ZABs, because CO 2 reacts with OH − and forms CO 2− 3 , thus reducing the electrolyte conductivity and slowing the cell reaction down. Appling a CO 2 filter could solve this problem, but it will increase the complexity and the cost of the system [23].
The evolution of hydrogen gas could be a challenge for electrolytes with a metal electrode with a lower potential than hydrogen evolution because the electrolyte becomes thermodynamically unstable [23]. When using an active electrolyte, the insoluble byproducts' deposition on both electrodes' surfaces during the charge-discharge cycles is a challenge that must be taken into consideration. These by-products reduce the battery's performance due to blocking the electrode pores, limiting air diffusion [16,162].
The absorption of moisture from the environment and the evaporation of electrolytes both contribute to the shortening of the life of aqueous MABs. As a result of the accumulation of water, air electrode flooding may occur, which may impair oxygen delivery to the active areas of the catalyst. However, water loss raises the electrolyte concentration in the body, which has a detrimental impact on the discharge response. Additionally, if the electrolyte is diluted, the ionic conductivity will be decreased, resulting in higher internal resistances in the system. When designing the battery, it is possible to optimize the internal water balance by considering the quantity of metal used, the composition and volume of the electrolyte, and the degree of gas diffusion. The polymerization of the electrolyte may help to decrease the amount of moisture that is lost. Furthermore, the use of a siloxane membrane protects against flooding and drying out [87].

Cathode Challenges
It is challenging to develop a bi-functional air catalyst that is stable, active, and inexpensive and is appropriate for both OER and ORR [23]. The precipitation of solid products such as Li 2 O 2 in the cathode results in a thick layer that inhibits electron transport and may even result in the blocking of cathode pores, reducing the overall capacity of the cell. The transfer of oxygen is a problem for certain types of MAB when operating at high current densities [23].

Conclusions
Metal-air batteries are promising electrochemical devices with a high energy density that are safe, environmentally friendly, and lightweight. MABs have a wide range of applications, including portable electric devices, wearable devices, and large-scale applications, such as electric cars, among many others. This work thoroughly discusses the mechanism of MABs, types, electrode materials, electrolytes, new designs, and new applications. The challenges and recommendations are given.
The following conclusions are driven: • Various metals can be used as an anode of MABs. Each metal has its own advantages and disadvantages. Al is one of the promising electrodes due to its high energy density, low weight, good recyclability, environmental friendliness, and low cost. • Despite the high ionic conductivity of the aqueous electrolytes, the leakage, stability, and thermodynamic limitations are challenges facing their application. Electrolyte additives or non-aqueous electrolytes can minimize or solve these problems and thus increase the durability and energy density of MABs. • A thermally and mechanically porous cathode electrode that can perform ORR and OER effectively is essential for commercial MABs.