Remote Microgrids for Energy Access in Indonesia—Part II: PV Microgrids and a Technology Outlook

: This paper is the companion paper of Remote Microgrids for Energy Access in Indonesia “ Part I: scaling and sustainability challenges and a technology outlook ”. This part II investigates the issues of photovoltaic (PV) systems with respect to the planning, design, and operation, and maintenance phases in microgrids in Indonesia. The technology outlooks are also included as PV has an important role in providing electricity in the underdeveloped, isolated, and border areas. The data in this paper are from PV microgrids located in Maluku and North Maluku, which are two provinces where there is barely any grid connection available and thus very dependent on remote microgrids. The data are obtained from interviews with Perusahaan Listrik Negara (PLN) and NZMATES, which are an Indonesian utility company and a program for supporting role for the PV systems in Maluku funded by New Zealand respectively. Common issues with respect to reliability and sustainability are identiﬁed based on the provided data. Advanced technologies to increase reliability and sustainability are also presented in this paper as a technology outlook. Among these solutions are online monitoring systems, PV and battery lifetime estimation, load forecasting strategies, and PV inverters technology.


Introduction
Indonesia is predicted to reach the peak of demographic dividend (when the population in working ages will be at the highest) between 2020-2030 [1] which theoretically has the potential to increase investments and output per capita. Consequently, Indonesia will face a significant challenge to provide (clean) energy everywhere. Since Indonesia is an island country, the development of a fully interconnected grid is a challenge. Many isolated islands or rural areas are not covered by the grid due to the lack of development and investment. The energy access disparity between the western part and eastern part in Indonesia is clearly prominent [2,3]. Western islands like Sumatra, Java, and Bali are oversupplied while the eastern islands like Maluku and North Maluku (MMU) have been struggling for a long time. This can be seen in Figure 1, where the electrification ratio per region is shown. The situation gets even worse when assessing the energy access attribute based on a multi-tier framework as was shown in part I of this publication.
Indonesia has committed to increasing the penetration of renewable energy to 23% and 29% in 2025 and 2030, respectively, as per Paris Agreement on Climate Change (UNFCCC). However, the total power generation is still mainly driven by coal power plants. Coal power plants contribute 49.85%, followed by gas power plants 28.06%, and diesel generators by However, the long-term reliability of PV microgrids has been an issue in Indonesia. Due to the shortcomings in the planning [7,8], design [7,9], and operation and maintenance (O&M) [10,11] phases, several problems emerge. There are a number of PV microgrids funded by MEMR that have a shorter lifetime (approx. 4 years) compared to the typical PV system lifetime (approx. 7 years), which was discovered via interviews with NZMATES [12]. The perceived reason for this was, that the MEMR funds seem to cover only initial investment costs. They include the costs made for design, procurement of materials, construction, and final commissioning, without provisions for the O&M costs. Consequently, the local government is expected to deal with the O&M costs, which in most cases were not taken into account. The lack of O&M can lead to problems with the PV microgrids' sustainability. This is a clear example of a technological issue that was identified as a potential challenge in Part I of this publication, "Te3: lack of O&M standard". Even though there are training activities for the operators in the villages, the training is not sufficient for the local government to be able to operate PV microgrids. As a result, Even though there are already more than a hundred outlying islands in Indonesia [6] that have been using PV off-grid, their impact on total energy generation is still too little. Therefore, the government has started actively supporting the usage of PV off-grid by providing funding to remote communities through the Ministry of Energy and Mineral Resources (MEMR). Tutukembung, Adaut, Wamana, and Ilwaki in the Maluku Province are examples of communities that already gained electricity access through that funding. PV microgrids are seen as a solution to increase the renewable energy penetration rate and accelerate the access to electricity in rural or remote areas, therefore increasing the electrification ratio and simultaneously contributing to the Paris Agreement.
However, the long-term reliability of PV microgrids has been an issue in Indonesia. Due to the shortcomings in the planning [7,8], design [7,9], and operation and maintenance (O&M) [10,11] phases, several problems emerge. There are a number of PV microgrids funded by MEMR that have a shorter lifetime (approx. 4 years) compared to the typical PV system lifetime (approx. 7 years), which was discovered via interviews with NZ-MATES [12]. The perceived reason for this was, that the MEMR funds seem to cover only initial investment costs. They include the costs made for design, procurement of materials, construction, and final commissioning, without provisions for the O&M costs. Consequently, the local government is expected to deal with the O&M costs, which in most cases were not taken into account. The lack of O&M can lead to problems with the PV microgrids' sustainability. This is a clear example of a technological issue that was identified as a potential challenge in Part I of this publication, "Te3: lack of O&M standard". Even though there are training activities for the operators in the villages, the training is not sufficient for the local government to be able to operate PV microgrids. As a result, the local operators will need to find technicians or engineers who commonly live or work far away from the microgrid location, resulting in longer downtimes and increased costs.
Many papers discuss the sustainability and reliability of PVs or microgrids. In [13,14], the scholars reported the techno-economic feasibility and sustainability analysis of hybrid microgrids. In [15,16], the authors improve the sustainability of a hybrid energy system Energies 2021, 14, 6901 3 of 18 by using a decentralized multiagent system (MAS) for power management in a hybrid microgrid, which increased efficiency and decreased operational costs altogether. A survey conducted by Energizing Development (Endev) [17] showed that the failure of PV microgrids in Indonesia were dominated by inverter failures and battery failures with an undetermined origin. However, it also showed that lightning strikes are a reoccurring source of failures. To increase sustainability and reliability, in [18][19][20] the authors proposed a novel modular microgrid architecture and management technique. It enables the optimization of multilayer control, reliability during the dynamic condition, and sustainability under normal and abnormal conditions. Unfortunately, these reports provided limited information about issues in the planning, design, and O&M phases.
This paper is the continuation of part I in which a multi-tier framework (MTF) has been developed. Part II continues by investigating in more detail the technological challenges during the planning, design, and O&M phases. Part II does this by focusing on the actual microgrid site conditions including the analysis from the relevant stakeholders. It also includes potential technologies that can improve the sustainability and reliability of PV microgrids.
The main contributions of part II of this paper are as follows: 1.
To investigate the actual problems in planning, design, and O&M phases of PV microgrids in Indonesia including the examples of PV hybrid systems in MMU. The PV hybrid in this paper is the combination between the PV system and diesel generator.

2.
To recommend several advanced microgrid technologies as technology outlook for PV microgrids in Indonesia such as microgrid online monitoring system, load forecasting estimation, PV panels degradation, battery state-of-health (SoH) estimation, and maximum energy yield strategies by deploying micro inverters and direct current (DC) optimizers.
The paper is structured as follows: Section 2 discusses microgrids in an Indonesian context based on a literature review, data, and interviews that were performed from PLN, NZMATES, and EnDev. More specifically why PV microgrids are so important for Indonesia, and the problems they are facing. Section 3 describes the technological outlook that can be adopted in PV microgrids in Indonesia to address those issues. Finally, some concluding remarks are made in Section 4.

Research Approach
The data in this paper were obtained through direct interviews and available data from PLN and NZMATES. PLN is an Indonesian state-owned corporation while NZMATES is a program funded by New Zealand to support the usage of renewable energy in Maluku. The data of the studied PV microgrids have been anonymized, as some details are confidential. Some of the PV microgrids are owned and operated by PLN, while others are funded by MEMR and operated by local communities with the technical assistance provided by NZMATES. The results were compared with a survey from EnDev to get a more complete picture of the microgrid conditions in Indonesia.

Indonesia Microgrids
In Figure 2 a classification scheme is given based on the size of microgrids and their connection to the grid or lack of. In Indonesia, only the larger microgrids seem to have an impact on the energy mix target 2025. Examples of large installations are PV Bontang and Oelpuah (more than 2 MW), Ulumbu and Matalako geothermal (more than 5 MW), Lubuk Sao, and Cibareno hydro powers (more than 2.5 MW), and Petapahan dan Damit Hulu biogas plants (more than 1 MW).
While smaller microgrids have less capacity, thus contributing relatively a small amount to the total renewable energy mix, they however are more suitable to reach isolated areas thus their potentials lie in the increased number of implementations. To increase numbers the Indonesian government has issued a policy to accelerate the electrification of underdeveloped, border, and outlying areas (often referred to as 3T areas). Data from Energies 2021, 14, 6901 4 of 18 the geoportal Ministry of Energy and Mineral Resources (MEMR) Indonesia shows that 714 isolated microgrids have been installed in the 3T areas. Even though the total power generated increased to 30 MW, covering around 100,000 households, it is shown that remote microgrids only contribute 0.3% of the total power generated in isolated microgrids owned by the MEMR.
Energies 2021, 14, x FOR PEER REVIEW 4 of 18 Sao, and Cibareno hydro powers (more than 2.5 MW), and Petapahan dan Damit Hulu biogas plants (more than 1 MW). While smaller microgrids have less capacity, thus contributing relatively a small amount to the total renewable energy mix, they however are more suitable to reach isolated areas thus their potentials lie in the increased number of implementations. To increase numbers the Indonesian government has issued a policy to accelerate the electrification of underdeveloped, border, and outlying areas (often referred to as 3T areas). Data from the geoportal Ministry of Energy and Mineral Resources (MEMR) Indonesia shows that 714 isolated microgrids have been installed in the 3T areas. Even though the total power generated increased to 30 MW, covering around 100,000 households, it is shown that remote microgrids only contribute 0.3% of the total power generated in isolated microgrids owned by the MEMR.

The Importance of PV Off-Grid Microgrids
The extension of the grid faces huge financial and technical barriers when providing or improving energy access to rural areas [21]. These barriers exist due to Indonesia's islanded structure, which makes supplying electricity to the 3T areas difficult. Next to this, the structures should take earthquakes into account, since Indonesia lies on the ring-offire which is at the meeting point of the Pacific, the Eurasian, and the Indo-Australia continental plates. These conditions make the development of a super-grid not feasible.
Since the Indonesian government issued some policies on renewable energy, the development of the microgrid has been increasing. However, power quality issues arise. The power quality of solar light in Maluku and North Maluku is low as the solar can only generate energy to light in the afternoon when the irradiation is high enough. Table 1 shows that the power quality disparity occurs in some underdeveloped areas in Indonesia. There are 68 villages and 50 villages in Maluku and North Maluku has access to solar light only which makes them depend on solar irradiation. Another thing is the isolated microgrids funded by MEMR contribute to around 30% in Maluku, while in North Maluku it is only 18%.

The Importance of PV Off-Grid Microgrids
The extension of the grid faces huge financial and technical barriers when providing or improving energy access to rural areas [21]. These barriers exist due to Indonesia's islanded structure, which makes supplying electricity to the 3T areas difficult. Next to this, the structures should take earthquakes into account, since Indonesia lies on the ring-of-fire which is at the meeting point of the Pacific, the Eurasian, and the Indo-Australia continental plates. These conditions make the development of a super-grid not feasible.
Since the Indonesian government issued some policies on renewable energy, the development of the microgrid has been increasing. However, power quality issues arise. The power quality of solar light in Maluku and North Maluku is low as the solar can only generate energy to light in the afternoon when the irradiation is high enough. Table 1 shows that the power quality disparity occurs in some underdeveloped areas in Indonesia. There are 68 villages and 50 villages in Maluku and North Maluku has access to solar light only which makes them depend on solar irradiation. Another thing is the isolated microgrids funded by MEMR contribute to around 30% in Maluku, while in North Maluku it is only 18%.
To achieve both mixed renewable energy mix and power quality targets, the PV microgrids can be a solution to increase the power quality and meet the mixed renewable energy target in 2030 as per Figure 3. The PV off-grids can help to improve attributes of energy access (capacity, availability, reliability, quality, and affordability), increase the electrification ratio, reduce the economic gap between rural and urban areas, and simultaneously the PV can increase the renewable energy mix target set by the Indonesian government. Besides that, the PV microgrids are more feasible than the super-grid in the medium term. The Indonesian government has initiated the 'Bright Indonesia Program' to provide energy access by utilizing more solar light as an energy source for the lighting in 2500 villages. To achieve both mixed renewable energy mix and power quality targets, the PV microgrids can be a solution to increase the power quality and meet the mixed renewable energy target in 2030 as per Figure 3. The PV off-grids can help to improve attributes of energy access (capacity, availability, reliability, quality, and affordability), increase the electrification ratio, reduce the economic gap between rural and urban areas, and simultaneously the PV can increase the renewable energy mix target set by the Indonesian government. Besides that, the PV microgrids are more feasible than the super-grid in the medium term. The Indonesian government has initiated the 'Bright Indonesia Program' to provide energy access by utilizing more solar light as an energy source for the lighting in 2500 villages.

Challenge of PV Microgrids in Indonesia
In part I: scaling sustainability challenge and a technology outlook, the framework has been developed and to link the challenge to the respective phases like planning, design, and operation and maintenance (O&M) phases. This sub-section explains the actual condition of PV sites in Indonesia. The cases in each phase are investigated and explored

Challenge of PV Microgrids in Indonesia
In part I: scaling sustainability challenge and a technology outlook, the framework has been developed and to link the challenge to the respective phases like planning, design, and operation and maintenance (O&M) phases. This sub-section explains the actual condition of PV sites in Indonesia. The cases in each phase are investigated and explored to understand the real condition and how to mitigate those issues. The suggestions are provided to extend the PVs site lifetime. Table 2 shows all 15 PV microgrids sites in MMU. The problems are identified with respect to the planning, design, and O&M phases and will be elaborated on in this paper. The first set of challenges (as per in framework in part I) that was identified via an interview with PLN and NZMATES is related to the planning phase. The load characterization, load forecast, and PV diesel generator sizing are investigated in the following sub-section. The second set of challenges is the design phase in which the PV system should be designed with a long lifetime and low losses. This includes the design architecture, automatic switch to simplify the operator works, and battery system design. The PV hybrid architecture and PV synchronization with the diesel generators are taken into account in this design phase. The third and last phase that is discussed in this paper is the O&M phase. The O&M activities are important to keep PV microgrids reliable and sustainable. Daily and monthly monitoring to detect the degradation and failure are needed to keep PV microgrids continuously generating power and delivering it to the community. Spare part availability and battery string condition are also discussed in the O&M phase. PV hybrid microgrid site 1 is given an example of poor load forecasting. The peak load was 3.5 kW in 2016, but since the energy access boosted the local economy, the peak load increased to 6.5 kW in 2019 as seen in Figure 4. The significantly increased load was a burden to the battery. Due to the high discharging rate, 16 out of 120 batteries were damaged resulting in an inadequate battery voltage for charging. Another consequence was that the diesel generator needed to operate longer than design anticipated which gave an impact on the operational costs (the cost of diesel fuel). This problem clearly shows that economic growth impact needs to be accounted for in proper load forecasting (capacity and availability MTF), which is already recommended in [8,14]. The battery bank should be upgraded, and the damaged batteries need to be replaced promptly to accommodate the load demand, otherwise, the remaining batteries can also degrade fast. As the PV power cannot cover the load for a full day, it can be used for a certain time like in the afternoon only. In the late evening or early morning, an additional diesel generator is needed. Another solution is by installing an additional PV system that can accommodate the load demand.
Energies 2021, 14, x FOR PEER REVIEW 7 of 18 The PV system could operate in the peak shaving only, where one or two generators can be turned off, thus keeping them operating above the 40% threshold. Another option is to cover 20-30% of the load demand by the PV installation, the remaining produced power can be used to charge a battery.
(a) (b) (c)   Figure 5 shows the condition of PV hybrid microgrid site 12. The microgrid has not been operating since 2019 even though the PV system was in a good condition. As the Energies 2021, 14, 6901 7 of 18 PV system was connected to the diesel generator as a hybrid, it made the specific fuel consumption (SFC) of the diesel generator not efficient. The PV inverter power was 100 kW while the nominal daily load was around 200 kW. It is known that the SFC diesel generator is typically optimum at 75-80% of the nominal rated capacity but degrades very rapidly when the diesel generator is operated below 40% of its rated capacity (affordability MTF).
The PV system could operate in the peak shaving only, where one or two generators can be turned off, thus keeping them operating above the 40% threshold. Another option is to cover 20-30% of the load demand by the PV installation, the remaining produced power can be used to charge a battery. cover 20-30% of the load demand by the PV installation, the remaining produced power can be used to charge a battery.

Design Phase
The case of PV hybrid site 14 is an example of a typical design phase problem as seen in Figure 6. The 100 kWp PV-diesel site 14 was designed for the isolated load condition, of which in the afternoon, the PV will cover the load, and in the evening, the load will be covered by the diesel generator. The operator needed to manually switch between the PV system and diesel generators. Due to this inefficient way of operation, the PV system were not used anymore (availability and reliability MTF). As a consequence, the inverter, combiner boxes, and powerhouse slowly decayed over time. An automated switch between operating conditions would circumvent this type of design flaw. The design phase needs to consider the existing diesel generator and how to interconnect the PV system with a minimum amount of manual labor, i.e., in the case of a hybrid microgrid, the operator should not need to go to the PV site, except for maintenance.

Design Phase
The case of PV hybrid site 14 is an example of a typical design phase problem as seen in Figure 6. The 100 kWp PV-diesel site 14 was designed for the isolated load condition, of which in the afternoon, the PV will cover the load, and in the evening, the load will be covered by the diesel generator. The operator needed to manually switch between the PV system and diesel generators. Due to this inefficient way of operation, the PV system were not used anymore (availability and reliability MTF). As a consequence, the inverter, combiner boxes, and powerhouse slowly decayed over time. An automated switch between operating conditions would circumvent this type of design flaw. The design phase needs to consider the existing diesel generator and how to interconnect the PV system with a minimum amount of manual labor, i.e., in the case of a hybrid microgrid, the operator should not need to go to the PV site, except for maintenance.
The system architectures of sites 1 and 8 are different with respect to the battery charger as shown in Figure 7. In the case of site 8, each battery system has its own battery charger, which is a bi-directional inverter, while PV site 1 uses the PV inverters as a battery charger. In [25] it was shown that if the demand load is more than 80% of the power generated by the PV, the layout of site 8 has the highest efficiency. If the load is less than 80% of the power generated and the excess energy charges the battery, site 3 will have the highest efficiency. Unfortunately, there is no site-specific data available to verify these expectations. The system architectures of sites 1 and 8 are different with respect to the battery charger as shown in Figure 7. In the case of site 8, each battery system has its own battery charger, which is a bi-directional inverter, while PV site 1 uses the PV inverters as a battery charger. In [25] it was shown that if the demand load is more than 80% of the power generated by the PV, the layout of site 8 has the highest efficiency. If the load is less than 80% of the power generated and the excess energy charges the battery, site 3 will have the highest efficiency. Unfortunately, there is no site-specific data available to verify these expectations. The battery was identified as the second highest failing component [12,[23][24] after the PV's inverter and thus requires to be well designed and maintained. The two parallel strings in Figure 7a will be suitable to accommodate the partial operation (reliability MTF) of the battery during the offline inspection and replacement activities (see examples in O&M). Air conditioning is mandatory for designing a battery room (if the ambient temperature is higher than manufacturer's recommendation) as per IEEE Std. 937-2019 as the battery life has a strong relationship to temperature and humidity. As seen in Figure  8, there is no temperature control in PV site 1 and only an exhaust fan in the battery room of PV site 14. As per IEEE std. 1561-2019, the lifetime of battery vented lead-acid (VLA) batteries will decrease about 50% for every 10 °C increments and 8.3 °C for the valve-  The system architectures of sites 1 and 8 are different with respect to the battery charger as shown in Figure 7. In the case of site 8, each battery system has its own battery charger, which is a bi-directional inverter, while PV site 1 uses the PV inverters as a battery charger. In [25] it was shown that if the demand load is more than 80% of the power generated by the PV, the layout of site 8 has the highest efficiency. If the load is less than 80% of the power generated and the excess energy charges the battery, site 3 will have the highest efficiency. Unfortunately, there is no site-specific data available to verify these expectations. The battery was identified as the second highest failing component [12,[23][24] after the PV's inverter and thus requires to be well designed and maintained. The two parallel strings in Figure 7a will be suitable to accommodate the partial operation (reliability MTF) of the battery during the offline inspection and replacement activities (see examples in O&M). Air conditioning is mandatory for designing a battery room (if the ambient temperature is higher than manufacturer's recommendation) as per IEEE Std. 937-2019 as the battery life has a strong relationship to temperature and humidity. As seen in Figure  8, there is no temperature control in PV site 1 and only an exhaust fan in the battery room of PV site 14. As per IEEE std. 1561-2019, the lifetime of battery vented lead-acid (VLA) batteries will decrease about 50% for every 10 °C increments and 8.3 °C for the valve- The battery was identified as the second highest failing component [12,23,24] after the PV's inverter and thus requires to be well designed and maintained. The two parallel strings in Figure 7a will be suitable to accommodate the partial operation (reliability MTF) of the battery during the offline inspection and replacement activities (see examples in O&M). Air conditioning is mandatory for designing a battery room (if the ambient temperature is higher than manufacturer's recommendation) as per IEEE Std. 937-2019 as the battery life has a strong relationship to temperature and humidity. As seen in Figure 8, there is no temperature control in PV site 1 and only an exhaust fan in the battery room of PV site 14. As per IEEE std. 1561-2019, the lifetime of battery vented lead-acid (VLA) batteries will decrease about 50% for every 10 • C increments and 8.3 • C for the valve-regulated lead acid (VRLA) batteries in permanent temperature operation over 25 • C (availability and reliability MTF).

Operation and Maintenance
Site 7 is a PV hybrid system, combining a 200 kWp PV capacity with a diesel generator of 880 kW. According to the load demand in that area, in the morning the load required approximately 650 kW and in the evening at the most 850 kW. Based on Figure 9 provided by PLN, in 2014, the energy generated from the PV system was around 550 kWh/day, but in 2015, this decreased to a maximum of 325 kWh/day. In Indonesia, the dry season is from April to October while the rainy season is then from November to March. Overall, the weather in either April or May will not differ that much. In this case, comparing the maximum of energy generated those were occurring one year apart can indicate the PV performance. By considering the peak values instead of averages, the data is not influenced by temporary fluctuations that are for instance caused by inverter restart issues or string voltage problems. During a year of operation, PV site 7 was degraded by more than 40%. This case shows that the O&M can be a crucial point to keep the reliability and availability of PV site 7. The battery (384 kWh/OPzS Shoto GFX-800 Ah (240 pcs)) system voltage was around 366 V, which is lower than the rated battery system voltage which is in the range of 420-480 V (in any state-of-charge level) as per in Figure 10. Further battery inspection needs to be conducted to decide which battery needs to be replaced or not. Through inspection, it was found that the PV modules were damaged, and the combiner boxes were rusty and corroded. Proper maintenance as per IEEE Std. 458-2020 could have avoided such a degradation.

Operation and Maintenance
Site 7 is a PV hybrid system, combining a 200 kWp PV capacity with a diesel generator of 880 kW. According to the load demand in that area, in the morning the load required approximately 650 kW and in the evening at the most 850 kW. Based on Figure 9 provided by PLN, in 2014, the energy generated from the PV system was around 550 kWh/day, but in 2015, this decreased to a maximum of 325 kWh/day. In Indonesia, the dry season is from April to October while the rainy season is then from November to March. Overall, the weather in either April or May will not differ that much. In this case, comparing the maximum of energy generated those were occurring one year apart can indicate the PV performance. By considering the peak values instead of averages, the data is not influenced by temporary fluctuations that are for instance caused by inverter restart issues or string voltage problems. During a year of operation, PV site 7 was degraded by more than 40%. This case shows that the O&M can be a crucial point to keep the reliability and availability of PV site 7. The battery (384 kWh/OPzS Shoto GFX-800 Ah (240 pcs)) system voltage was around 366 V, which is lower than the rated battery system voltage which is in the range of 420-480 V (in any state-of-charge level) as per in Figure 10. Further battery inspection needs to be conducted to decide which battery needs to be replaced or not. Through inspection, it was found that the PV modules were damaged, and the combiner boxes were rusty and corroded. Proper maintenance as per IEEE Std. 458-2020 could have avoided such a degradation.

Operation and Maintenance
Site 7 is a PV hybrid system, combining a 200 kWp PV capacity with a diesel generator of 880 kW. According to the load demand in that area, in the morning the load required approximately 650 kW and in the evening at the most 850 kW. Based on Figure 9 provided by PLN, in 2014, the energy generated from the PV system was around 550 kWh/day, but in 2015, this decreased to a maximum of 325 kWh/day. In Indonesia, the dry season is from April to October while the rainy season is then from November to March. Overall, the weather in either April or May will not differ that much. In this case, comparing the maximum of energy generated those were occurring one year apart can indicate the PV performance. By considering the peak values instead of averages, the data is not influenced by temporary fluctuations that are for instance caused by inverter restart issues or string voltage problems. During a year of operation, PV site 7 was degraded by more than 40%. This case shows that the O&M can be a crucial point to keep the reliability and availability of PV site 7. The battery (384 kWh/OPzS Shoto GFX-800 Ah (240 pcs)) system voltage was around 366 V, which is lower than the rated battery system voltage which is in the range of 420-480 V (in any state-of-charge level) as per in Figure 10. Further battery inspection needs to be conducted to decide which battery needs to be replaced or not. Through inspection, it was found that the PV modules were damaged, and the combiner boxes were rusty and corroded. Proper maintenance as per IEEE Std. 458-2020 could have avoided such a degradation.   Site 13 has a 600 kWp PV installation which is connected to a private diesel generator of 2 MW and a PLN owned diesel generator of 2.3 MW (standby mode). PV site 13 has operated for 6 years, but due to a battery charger problem, it stopped working. A component failure occurred in the battery charger; thus, the battery system was out of order. The manufacturer of the battery charger was permanently closed; therefore, a replacement was not an option. When the PV was operating in conjunction with the diesel generator without any energy buffering, the fluctuated power created a problem for the diesel generator. Therefore, the operator turned off the PV installation (quality MTF).
The best maintenance of the PV inverters and battery charger would be based on the manufacturer's standards (Table 3), but how corrosive the location, ambient temperature, and humidity should be taken into consideration as discussed in site 13. Availability of spare parts are the crucial point to ensure the operation of the PV system, especially for sensitive equipment like IGBT inverter and battery modules. For example, PV site 2 was not in operation due to IGBT failure, and PV site 3 was not operational because of battery   Site 13 has a 600 kWp PV installation which is connected to a private diesel generator of 2 MW and a PLN owned diesel generator of 2.3 MW (standby mode). PV site 13 has operated for 6 years, but due to a battery charger problem, it stopped working. A component failure occurred in the battery charger; thus, the battery system was out of order. The manufacturer of the battery charger was permanently closed; therefore, a replacement was not an option. When the PV was operating in conjunction with the diesel generator without any energy buffering, the fluctuated power created a problem for the diesel generator. Therefore, the operator turned off the PV installation (quality MTF).
The best maintenance of the PV inverters and battery charger would be based on the manufacturer's standards (Table 3), but how corrosive the location, ambient temperature, and humidity should be taken into consideration as discussed in site 13. Availability of spare parts are the crucial point to ensure the operation of the PV system, especially for sensitive equipment like IGBT inverter and battery modules. For example, PV site 2 was not in operation due to IGBT failure, and PV site 3 was not operational because of battery Site 13 has a 600 kWp PV installation which is connected to a private diesel generator of 2 MW and a PLN owned diesel generator of 2.3 MW (standby mode). PV site 13 has operated for 6 years, but due to a battery charger problem, it stopped working. A component failure occurred in the battery charger; thus, the battery system was out of order. The manufacturer of the battery charger was permanently closed; therefore, a replacement was not an option. When the PV was operating in conjunction with the diesel generator without any energy buffering, the fluctuated power created a problem for the diesel generator. Therefore, the operator turned off the PV installation (quality MTF).
The best maintenance of the PV inverters and battery charger would be based on the manufacturer's standards (Table 3), but how corrosive the location, ambient temperature, and humidity should be taken into consideration as discussed in site 13. Availability of spare parts are the crucial point to ensure the operation of the PV system, especially for sensitive equipment like IGBT inverter and battery modules. For example, PV site 2 was not in operation due to IGBT failure, and PV site 3 was not operational because of battery failure (480 kWh/OPzS FIAMM LM 1000 ah (120 pcs)) with the actual voltage is 112 V only, which is lower than the rated battery system voltage in the range of 192-240 V (reliability MTF) as per Figure 12.

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues = in Good Condition; ation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues -

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability a sustainability of the PV microgrids in Indonesia. The considered technology outlook a remote monitoring systems, battery and PV lifetime estimation, load forecasting, and t different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to depl online control and monitoring system for the grid in the Maluku area. However, t roadmap does not show an online monitoring focus on PV systems. The roadmap SCAD PLN MMU is focused on switching equipment (load break switches, reclosers, and circ breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects th can be monitored such as PV panel conditions, battery performance, and power generat from PV systems which can extend the PV's lifetime and increase power quality. In ad tion, the online monitoring system provides real-time information and can reduce t O&M cost such as reducing the operator's cost and increasing the power quality by es mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, vo age, power, and energy are the main data to be monitored, but due to the technolo development, the batteries and the PV panels lifetime can also be monitored as per issu has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

Technology Recommendations
This section focuses on the technology recommendati sustainability of the PV microgrids in Indonesia. The cons remote monitoring systems, battery and PV lifetime estima different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN online control and monitoring system for the grid in th roadmap does not show an online monitoring focus on PV s PLN MMU is focused on switching equipment (load break breakers) for controlling, and cubicles only for monitoring can be monitored such as PV panel conditions, battery perfo from PV systems which can extend the PV's lifetime and in tion, the online monitoring system provides real-time in O&M cost such as reducing the operator's cost and increa mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of age, power, and energy are the main data to be monitor development, the batteries and the PV panels lifetime can a n/a Site 2 IGBT Inverter -n/a n/a attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.
attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.
attached underneath the PV panels to operate the panel individually. Th micro-inverter is to operate MPPT separately in each PV panel. Therefore, w has partial shading, only this particular panel operates below maximum po other PV panels operate in the maximum tracking point. Additionally, the has a unique serial number which makes it easy to monitor each PV panel' ation and identify the degradation of the individual PV panel. The DC opti vides the same benefit as the micro-inverter for the battery monitoring, bu mizer does not increase the single point of the failure condition. Table 5 s parison of the string inverters, micro-inverters, and DC optimizers with di nies.

Conclusions
The second part of the paper series has analyzed the potential techn that were identified in the first part of the series. During the developmen work, four distinct challenges were identified. First, the lack of practica knowledge and inadequate preliminary survey were observed. Second, th of local skilled personnel. Third, the lack of O&M standards and lastly iss tified regarding Power Quality. Which are high-level descriptions, that ha rated on in this paper's part II. The PV microgrid conditions in Indonesi gated by data provided by the relevant stakeholders such as PLN, NZMAT Site 3 Battery l shading impact to the string inverters [42]. A micro-inverter is a small inverter underneath the PV panels to operate the panel individually. The benefit of the erter is to operate MPPT separately in each PV panel. Therefore, when one panel l shading, only this particular panel operates below maximum power, while the panels operate in the maximum tracking point. Additionally, the micro-inverter que serial number which makes it easy to monitor each PV panel's power generidentify the degradation of the individual PV panel. The DC optimizer [43] prosame benefit as the micro-inverter for the battery monitoring, but the DC opties not increase the single point of the failure condition. Table 5 shows the comf the string inverters, micro-inverters, and DC optimizers with different compan of selected string inverters, micro-inverters, and DC optimizers. sions second part of the paper series has analyzed the potential technical challenges identified in the first part of the series. During the development of the framer distinct challenges were identified. First, the lack of practical and technical e and inadequate preliminary survey were observed. Second, there was a lack killed personnel. Third, the lack of O&M standards and lastly issues were idenarding Power Quality. Which are high-level descriptions, that have been elaboin this paper's part II. The PV microgrid conditions in Indonesia were investidata provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

Model
the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues -?
to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.
to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

Technology Recommendations
This section focuses on the technology sustainability of the PV microgrids in Indon remote monitoring systems, battery and PV different type of PV inverters are presented

Online Monitoring Solution
In the roadmap SCADA PLN MMU 20 online control and monitoring system for roadmap does not show an online monitorin PLN MMU is focused on switching equipme breakers) for controlling, and cubicles only can be monitored such as PV panel condition from PV systems which can extend the PV's tion, the online monitoring system provid O&M cost such as reducing the operator's c mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring a age, power, and energy are the main data development, the batteries and the PV pane

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability a sustainability of the PV microgrids in Indonesia. The considered technology outlook a remote monitoring systems, battery and PV lifetime estimation, load forecasting, and t different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to depl online control and monitoring system for the grid in the Maluku area. However, t roadmap does not show an online monitoring focus on PV systems. The roadmap SCAD PLN MMU is focused on switching equipment (load break switches, reclosers, and circ breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects th can be monitored such as PV panel conditions, battery performance, and power generat from PV systems which can extend the PV's lifetime and increase power quality. In ad tion, the online monitoring system provides real-time information and can reduce t O&M cost such as reducing the operator's cost and increasing the power quality by es mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, vo age, power, and energy are the main data to be monitored, but due to the technolo development, the batteries and the PV panels lifetime can also be monitored as per issu micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. the string inverters architecture. To improve the lifetime of the PV syste inverter single point of failure, it can be converted to multiple points of f micro-inverter technology. Moreover, the micro-inverter increases the en to the individual maximum power point tracking (MPPT) in each panel wh the partial shading impact to the string inverters [42]. A micro-inverter is a attached underneath the PV panels to operate the panel individually. Th micro-inverter is to operate MPPT separately in each PV panel. Therefore, w has partial shading, only this particular panel operates below maximum po other PV panels operate in the maximum tracking point. Additionally, the has a unique serial number which makes it easy to monitor each PV panel' ation and identify the degradation of the individual PV panel. The DC opti vides the same benefit as the micro-inverter for the battery monitoring, bu mizer does not increase the single point of the failure condition. Table 5 s parison of the string inverters, micro-inverters, and DC optimizers with di nies.

Conclusions
The second part of the paper series has analyzed the potential techn that were identified in the first part of the series. During the developmen work, four distinct challenges were identified. First, the lack of practica knowledge and inadequate preliminary survey were observed. Second, th of local skilled personnel. Third, the lack of O&M standards and lastly iss tified regarding Power Quality. Which are high-level descriptions, that ha rated on in this paper's part II. The PV microgrid conditions in Indonesi gated by data provided by the relevant stakeholders such as PLN, NZMAT

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability a sustainability of the PV microgrids in Indonesia. The considered technology outlook a remote monitoring systems, battery and PV lifetime estimation, load forecasting, and t different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to depl online control and monitoring system for the grid in the Maluku area. However, t roadmap does not show an online monitoring focus on PV systems. The roadmap SCAD PLN MMU is focused on switching equipment (load break switches, reclosers, and circ breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects th can be monitored such as PV panel conditions, battery performance, and power generat from PV systems which can extend the PV's lifetime and increase power quality. In ad tion, the online monitoring system provides real-time information and can reduce t O&M cost such as reducing the operator's cost and increasing the power quality by es mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, vo age, power, and energy are the main data to be monitored, but due to the technolo development, the batteries and the PV panels lifetime can also be monitored as per issu

Technology Recommendations
This section focuses on the technology recommendation to ensure th sustainability of the PV microgrids in Indonesia. The considered techno remote monitoring systems, battery and PV lifetime estimation, load fore different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is pla online control and monitoring system for the grid in the Maluku are roadmap does not show an online monitoring focus on PV systems. The r PLN MMU is focused on switching equipment (load break switches, reclo breakers) for controlling, and cubicles only for monitoring. There are a lo can be monitored such as PV panel conditions, battery performance, and p from PV systems which can extend the PV's lifetime and increase power tion, the online monitoring system provides real-time information and O&M cost such as reducing the operator's cost and increasing the powe mating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. T age, power, and energy are the main data to be monitored, but due to development, the batteries and the PV panels lifetime can also be monito

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inve the string inverters architecture. To improve the lifetime of the PV syste inverter single point of failure, it can be converted to multiple points of f micro-inverter technology. Moreover, the micro-inverter increases the en to the individual maximum power point tracking (MPPT) in each panel wh the partial shading impact to the string inverters [42]. A micro-inverter is a attached underneath the PV panels to operate the panel individually. Th micro-inverter is to operate MPPT separately in each PV panel. Therefore, w has partial shading, only this particular panel operates below maximum po other PV panels operate in the maximum tracking point. Additionally, the has a unique serial number which makes it easy to monitor each PV panel' ation and identify the degradation of the individual PV panel. The DC opti vides the same benefit as the micro-inverter for the battery monitoring, bu mizer does not increase the single point of the failure condition. Table 5 s parison of the string inverters, micro-inverters, and DC optimizers with di nies.

Conclusions
The second part of the paper series has analyzed the potential techn that were identified in the first part of the series. During the developmen work, four distinct challenges were identified. First, the lack of practica knowledge and inadequate preliminary survey were observed. Second, th of local skilled personnel. Third, the lack of O&M standards and lastly iss tified regarding Power Quality. Which are high-level descriptions, that ha rated on in this paper's part II. The PV microgrid conditions in Indonesi gated by data provided by the relevant stakeholders such as PLN, NZMAT

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit

Technology Recommendations
This section focuses on the technology recommendation to ensure the reliability and sustainability of the PV microgrids in Indonesia. The considered technology outlook are remote monitoring systems, battery and PV lifetime estimation, load forecasting, and the different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku is planning to deploy online control and monitoring system for the grid in the Maluku area. However, the roadmap does not show an online monitoring focus on PV systems. The roadmap SCADA PLN MMU is focused on switching equipment (load break switches, reclosers, and circuit breakers) for controlling, and cubicles only for monitoring. There are a lot of aspects that can be monitored such as PV panel conditions, battery performance, and power generated from PV systems which can extend the PV's lifetime and increase power quality. In addition, the online monitoring system provides real-time information and can reduce the O&M cost such as reducing the operator's cost and increasing the power quality by estimating the PV's and battery's lifetime. Figure 13 shows a typical monitoring architecture of PV systems. The current, voltage, power, and energy are the main data to be monitored, but due to the technology development, the batteries and the PV panels lifetime can also be monitored as per issues in sites 3, 7, and 13. The PV and battery's maintenances can be scheduled based on the online monitoring systems and the O&M costs can be reduced. The data from PV, battery management systems (BMS), inverters, energy meters, and relays are collected in the data Energies 2021, 14, 6901 12 of 18 acquisition unit. Then the data can be delivered to the local monitoring system by cable or Wi-Fi communication. To increase data accessibility, the data can be uploaded to the internet cloud system and monitored via a mobile phone, tablet, or personal computer (PC) through the internet. Few online monitoring companies provide these services like 60 hertz, canopy power, and ferntech. Furthermore, in the high microgrid penetration, ref [27] proposed the cloud-based and hybrid wireless mesh communication framework for bilevel, nested, distributed optimization of networked clusters of microgrids. This method introduced the optimization framework communication in the high microgrid systems as per IEC 61,850 to achieve a certain delay performance and guaranteed optimization convergence. To reduce the cost, ref [28] proposed the decentralized smart grid using the 'edge of the network' to reduce the monitoring systems' cost. The nanogenerators as self-powered sensors can be added to monitor the PV systems with low losses [29,30]. This cloud-based system and 'edge of the network' can be adopted in sites 5 and 14. The distributed optimization can be used in site 5, therefore, there is optimum communication between PV, battery, and diesel generator to reduce the diesel generator's SFC. In site 14, the layer communication can link the operation of PV and diesel generator, thus, the switch breaker can be operated automatically. in sites 3, 7, and 13. The PV and battery's maintenances can be scheduled based on the online monitoring systems and the O&M costs can be reduced. The data from PV, battery management systems (BMS), inverters, energy meters, and relays are collected in the data acquisition unit. Then the data can be delivered to the local monitoring system by cable or Wi-Fi communication. To increase data accessibility, the data can be uploaded to the internet cloud system and monitored via a mobile phone, tablet, or personal computer (PC) through the internet. Few online monitoring companies provide these services like 60 hertz, canopy power, and ferntech. Furthermore, in the high microgrid penetration, ref [27] proposed the cloud-based and hybrid wireless mesh communication framework for bilevel, nested, distributed optimization of networked clusters of microgrids. This method introduced the optimization framework communication in the high microgrid systems as per IEC 61,850 to achieve a certain delay performance and guaranteed optimization convergence. To reduce the cost, ref [28] proposed the decentralized smart grid using the 'edge of the network' to reduce the monitoring systems' cost. The nanogenerators as selfpowered sensors can be added to monitor the PV systems with low losses [29,30]. This cloud-based system and 'edge of the network' can be adopted in sites 5 and 14. The distributed optimization can be used in site 5, therefore, there is optimum communication between PV, battery, and diesel generator to reduce the diesel generator's SFC. In site 14, the layer communication can link the operation of PV and diesel generator, thus, the switch breaker can be operated automatically.

Routers Local Monitoring System
Irradiance & Temperature Remote Monitoring System Figure 13. The typical online monitoring system of PV microgrids. Figure 13. The typical online monitoring system of PV microgrids.

PV and Battery Lifetime Estimation
The simple way to estimate the PV panel condition is to measure the voltage and current output and visual check of the PV panels, but this conventional method has a wide range of error since the irradiance and temperature affect the current and voltage, while a visual check requires more time to look into the cracks and black spots in PV panels. To reduce the visual checking time and to predict the PV panel degradation, machine learning (ML) algorithms could be implemented [31,32]. In [32], the authors proposed unmanned aerial vehicles (UAVs) with infrared (IR) and visible images in the red-green-blue (RGB) channel techniques to estimate the RUL of the PV modules as per Figure 14. The drone will irradiate the PV panels and evaluate the thermographic behavior of the PV modules. The images will be processed by a decision support system to estimate the degradation of the PV panels. This PV panel's lifetime estimation can solve the site 7 issue and help the operator to decide what treatment or maintenance can be performed to solve that issue. The operator can then decide on a replacement schedule of PV panels. This technology can reduce the O&M costs and keep the PV system continuously generating energy.

PV and Battery Lifetime Estimation
The simple way to estimate the PV panel condition is to measure the voltage and current output and visual check of the PV panels, but this conventional method has a wide range of error since the irradiance and temperature affect the current and voltage, while a visual check requires more time to look into the cracks and black spots in PV panels. To reduce the visual checking time and to predict the PV panel degradation, machine learning (ML) algorithms could be implemented [31,32]. In [32], the authors proposed unmanned aerial vehicles (UAVs) with infrared (IR) and visible images in the red-green-blue (RGB) channel techniques to estimate the RUL of the PV modules as per Figure 14. The drone will irradiate the PV panels and evaluate the thermographic behavior of the PV modules. The images will be processed by a decision support system to estimate the degradation of the PV panels. This PV panel's lifetime estimation can solve the site 7 issue and help the operator to decide what treatment or maintenance can be performed to solve that issue. The operator can then decide on a replacement schedule of PV panels. This technology can reduce the O&M costs and keep the PV system continuously generating energy. For the energy storage system (ESS), the authors in [33] showed that lithium-ion battery has a higher cycle, lower maintenance, and is more efficient compared to the leadacid battery, although it is more expensive. BMS is the technology to keep the batteries are in a good condition by using cell balancing, under and over-voltage protection and temperature management. Another battery storage technology is the battery RUL estimation. There are two types of battery RUL estimation. The first is the offline measurement The battery must be unplugged from the system before the parameter related to the battery RUL are measured. The second is the battery RUL online measurement where the battery is still plugged into the system. The advanced technology for the battery RUL measurement is the electrochemical impedance measurement (EIS). The EIS injects a ripple current to the battery, and since the battery has a unique characteristic impedance, the battery output terminal voltage will respond to the current and the battery internal impedance can be obtained [34,35]. The impedance of the battery has a strong relationship to the battery RUL which is typically the battery's internal impedance will increase due to the cycle time as seen in Figure 15. Sites 1, 7, and 14 can use the EIS method to estimate the battery lifetime and decide further action to mitigate the damage to the battery. For the energy storage system (ESS), the authors in [33] showed that lithium-ion battery has a higher cycle, lower maintenance, and is more efficient compared to the lead-acid battery, although it is more expensive. BMS is the technology to keep the batteries are in a good condition by using cell balancing, under and over-voltage protection and temperature management. Another battery storage technology is the battery RUL estimation. There are two types of battery RUL estimation. The first is the offline measurement The battery must be unplugged from the system before the parameter related to the battery RUL are measured. The second is the battery RUL online measurement where the battery is still plugged into the system. The advanced technology for the battery RUL measurement is the electrochemical impedance measurement (EIS). The EIS injects a ripple current to the battery, and since the battery has a unique characteristic impedance, the battery output terminal voltage will respond to the current and the battery internal impedance can be obtained [34,35]. The impedance of the battery has a strong relationship to the battery RUL which is typically the battery's internal impedance will increase due to the cycle time as seen in Figure 15. Sites 1, 7, and 14 can use the EIS method to estimate the battery lifetime and decide further action to mitigate the damage to the battery.

Load Forecasting
Load forecasting strategies are part of the planning issues which need to be well estimated as a basis of PV, diesel generator, and battery sizing. The medium-term load forecast (MTLF) and long-time load forecast (LTLF) need to be accurately estimated at the beginning of the design phase since this estimation will affect the expansion area, spare, and space in the substation cubicles, inverter-diesel generator synchronization, and automatic switch. While the short-time load forecast (STLF) needs to be calculated for the source load balancing and the energy fluctuation in the battery system. Different methods can be applied to estimate the load depending on the model identification and load characterization. Normally MTLF and LTLF use the trend analysis, end-use analysis, econometric analysis, neural network technique, and multiple linear regression, while STLF is calculated by fitting data, extrapolation, and linear regression. The neural network (NN) method is the famous strategy to provide high accuracy for the long-term estimation, but the training data are needed and updated to increase the accuracy. While support vector machine (SVM) uses only a subset of a dataset as training data and makes a faster estimation, but in general, the accuracy of SVM is lower than NN. These LTLF methods estimate the load forecast from few years up to 20 years and can be applied to site 1 in the planning phase to mitigate the poor load forecast. When the load growth is higher than the energy generated from the existing PV microgrid, additional PV panels can be installed depending on the rating of the batteries, inverters, panels, and other supporting equipment. While, when the load is lower than the energy generated from PV, the PV can help another village to supply electricity if the distance is considered taken into account. Table 4 shows the references for the load forecasting strategies.

Load Forecasting
Load forecasting strategies are part of the planning issues which need to be well estimated as a basis of PV, diesel generator, and battery sizing. The medium-term load forecast (MTLF) and long-time load forecast (LTLF) need to be accurately estimated at the beginning of the design phase since this estimation will affect the expansion area, spare, and space in the substation cubicles, inverter-diesel generator synchronization, and automatic switch. While the short-time load forecast (STLF) needs to be calculated for the source load balancing and the energy fluctuation in the battery system. Different methods can be applied to estimate the load depending on the model identification and load characterization. Normally MTLF and LTLF use the trend analysis, end-use analysis, econometric analysis, neural network technique, and multiple linear regression, while STLF is calculated by fitting data, extrapolation, and linear regression. The neural network (NN) method is the famous strategy to provide high accuracy for the long-term estimation, but the training data are needed and updated to increase the accuracy. While support vector machine (SVM) uses only a subset of a dataset as training data and makes a faster estimation, but in general, the accuracy of SVM is lower than NN. These LTLF methods estimate the load forecast from few years up to 20 years and can be applied to site 1 in the planning phase to mitigate the poor load forecast. When the load growth is higher than the energy generated from the existing PV microgrid, additional PV panels can be installed depending on the rating of the batteries, inverters, panels, and other supporting equipment. While, when the load is lower than the energy generated from PV, the PV can help another village to supply electricity if the distance is considered taken into account. Table 4 shows the references for the load forecasting strategies. For example, in site 1, the LTLF based on the bottom-up feature such as feeder load composition, large customer net load change, distributed energy resources adop-Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies. growth, and the previous-year peak demand can be calculated. The feeder load consumption and the residential and commercial peak load percentage can be estimated by Equations (1) and (3). While the distributed energy resources can be estimated by Equation (2) [41].

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.
Energies 2021, 14, x FOR PEER REVIEW growth, and the previous-year peak demand can be calculated. The feeder loa tion and the residential and commercial peak load percentage can be estimat tions (1) and (3). While the distributed energy resources can be estimated by [41].

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverte the string inverters architecture. To improve the lifetime of the PV system inverter single point of failure, it can be converted to multiple points of failu micro-inverter technology. Moreover, the micro-inverter increases the energ to the individual maximum power point tracking (MPPT) in each panel which the partial shading impact to the string inverters [42]. A micro-inverter is a sm attached underneath the PV panels to operate the panel individually. The b micro-inverter is to operate MPPT separately in each PV panel. Therefore, wh has partial shading, only this particular panel operates below maximum pow other PV panels operate in the maximum tracking point. Additionally, the m has a unique serial number which makes it easy to monitor each PV panel's p ation and identify the degradation of the individual PV panel. The DC optimi vides the same benefit as the micro-inverter for the battery monitoring, but mizer does not increase the single point of the failure condition. Table 5 sho parison of the string inverters, micro-inverters, and DC optimizers with diffe nies.

Conclusions
The second part of the paper series has analyzed the potential technica that were identified in the first part of the series. During the development o work, four distinct challenges were identified. First, the lack of practical a knowledge and inadequate preliminary survey were observed. Second, ther of local skilled personnel. Third, the lack of O&M standards and lastly issue tified regarding Power Quality. Which are high-level descriptions, that have rated on in this paper's part II. The PV microgrid conditions in Indonesia w gated by data provided by the relevant stakeholders such as PLN, NZMATES,

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev.
Energies 2021, 14, x FOR PEER REVIEW growth, and the previous-year peak demand can be calculated. The feeder loa tion and the residential and commercial peak load percentage can be estimat tions (1) and (3). While the distributed energy resources can be estimated by [41].

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverte the string inverters architecture. To improve the lifetime of the PV system inverter single point of failure, it can be converted to multiple points of failu micro-inverter technology. Moreover, the micro-inverter increases the energ to the individual maximum power point tracking (MPPT) in each panel which the partial shading impact to the string inverters [42]. A micro-inverter is a sm attached underneath the PV panels to operate the panel individually. The b micro-inverter is to operate MPPT separately in each PV panel. Therefore, wh has partial shading, only this particular panel operates below maximum pow other PV panels operate in the maximum tracking point. Additionally, the m has a unique serial number which makes it easy to monitor each PV panel's p ation and identify the degradation of the individual PV panel. The DC optimi vides the same benefit as the micro-inverter for the battery monitoring, but mizer does not increase the single point of the failure condition. Table 5 sho parison of the string inverters, micro-inverters, and DC optimizers with diffe nies.

Conclusions
The second part of the paper series has analyzed the potential technica that were identified in the first part of the series. During the development o work, four distinct challenges were identified. First, the lack of practical a knowledge and inadequate preliminary survey were observed. Second, ther of local skilled personnel. Third, the lack of O&M standards and lastly issue tified regarding Power Quality. Which are high-level descriptions, that have rated on in this paper's part II. The PV microgrid conditions in Indonesia w gated by data provided by the relevant stakeholders such as PLN, NZMATES, failure (480 kWh/OPzS FIAMM LM 1000 ah (120 pcs)) with the a only, which is lower than the rated battery system voltage in the ra ability MTF) as per Figure 12.

Technology Recommendations
This section focuses on the technology recommendation to en sustainability of the PV microgrids in Indonesia. The considered t remote monitoring systems, battery and PV lifetime estimation, loa different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku online control and monitoring system for the grid in the Maluk roadmap does not show an online monitoring focus on PV systems. PLN MMU is focused on switching equipment (load break switche breakers) for controlling, and cubicles only for monitoring. There a can be monitored such as PV panel conditions, battery performance from PV systems which can extend the PV's lifetime and increase p tion, the online monitoring system provides real-time informatio O&M cost such as reducing the operator's cost and increasing the

Technology Recommendations
This section focuses on the technology rec sustainability of the PV microgrids in Indones remote monitoring systems, battery and PV lif different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020 online control and monitoring system for th roadmap does not show an online monitoring f PLN MMU is focused on switching equipment breakers) for controlling, and cubicles only for can be monitored such as PV panel conditions, from PV systems which can extend the PV's lif tion, the online monitoring system provides O&M cost such as reducing the operator's cos failure (480 kWh/OPzS FIAMM LM 1000 ah (120 pcs)) with the a only, which is lower than the rated battery system voltage in the ra ability MTF) as per Figure 12.

Technology Recommendations
This section focuses on the technology recommendation to en sustainability of the PV microgrids in Indonesia. The considered t remote monitoring systems, battery and PV lifetime estimation, loa different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020-2024, PLN Maluku online control and monitoring system for the grid in the Maluk roadmap does not show an online monitoring focus on PV systems. PLN MMU is focused on switching equipment (load break switche breakers) for controlling, and cubicles only for monitoring. There a can be monitored such as PV panel conditions, battery performance from PV systems which can extend the PV's lifetime and increase p tion, the online monitoring system provides real-time informatio

Technology Recommendations
This section focuses on the technology rec sustainability of the PV microgrids in Indones remote monitoring systems, battery and PV lif different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020 online control and monitoring system for th roadmap does not show an online monitoring f PLN MMU is focused on switching equipment breakers) for controlling, and cubicles only for can be monitored such as PV panel conditions, from PV systems which can extend the PV's lif tion, the online monitoring system provides growth, and the previous-year peak demand can be calculated. The feeder load consumption and the residential and commercial peak load percentage can be estimated by Equations (1)

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elabo-

Technology Recommendations
This section focuses on the technology rec sustainability of the PV microgrids in Indones remote monitoring systems, battery and PV lif different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020 online control and monitoring system for th roadmap does not show an online monitoring f PLN MMU is focused on switching equipment breakers) for controlling, and cubicles only for can be monitored such as PV panel conditions, growth, and the previous-year peak demand can be calculated. The feeder load consumption and the residential and commercial peak load percentage can be estimated by Equations (1)

PV Inverters Technology
Based on the data from PLN Maluku, the architecture of the PV inverters is always the string inverters architecture. To improve the lifetime of the PV systems due to the inverter single point of failure, it can be converted to multiple points of failure by using micro-inverter technology. Moreover, the micro-inverter increases the energy yield due to the individual maximum power point tracking (MPPT) in each panel which can prevent the partial shading impact to the string inverters [42]. A micro-inverter is a small inverter attached underneath the PV panels to operate the panel individually. The benefit of the micro-inverter is to operate MPPT separately in each PV panel. Therefore, when one panel has partial shading, only this particular panel operates below maximum power, while the other PV panels operate in the maximum tracking point. Additionally, the micro-inverter has a unique serial number which makes it easy to monitor each PV panel's power generation and identify the degradation of the individual PV panel. The DC optimizer [43] provides the same benefit as the micro-inverter for the battery monitoring, but the DC optimizer does not increase the single point of the failure condition. Table 5 shows the comparison of the string inverters, micro-inverters, and DC optimizers with different companies.

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were iden-

Technology Recommendations
This section focuses on the technology rec sustainability of the PV microgrids in Indones remote monitoring systems, battery and PV lif different type of PV inverters are presented.

Online Monitoring Solution
In the roadmap SCADA PLN MMU 2020 online control and monitoring system for th roadmap does not show an online monitoring f PLN MMU is focused on switching equipment breakers) for controlling, and cubicles only for

Conclusions
The second part of the paper series has analyzed the potential technical challenges that were identified in the first part of the series. During the development of the framework, four distinct challenges were identified. First, the lack of practical and technical knowledge and inadequate preliminary survey were observed. Second, there was a lack of local skilled personnel. Third, the lack of O&M standards and lastly issues were identified regarding Power Quality. Which are high-level descriptions, that have been elaborated on in this paper's part II. The PV microgrid conditions in Indonesia were investigated by data provided by the relevant stakeholders such as PLN, NZMATES, and EnDev. Not all data was quantifiable, as some of it was provided via interviews. Although it sometimes leads to qualitative analysis, the actual problems related to the PV planning, design, and O&M phases were investigated.
It can be concluded that during the planning phase, load characterization didn't anticipate (heavy) growth patterns thus PV and battery were undersized. Estimation strategies have to be implemented to ensure the correct sizing.
During the design phase, it was observed that local climate was often not taken into account. Batteries should be in a steady low-temperature environment but were found in warm rooms, thus reducing the lifetime considerably. Which attributes to the overall short lifetime of the microgrid systems under investigation.
Using a proper O&M standard or protocol, the degradation of the batteries could be taken into account, thus ensuring high energy generation. Which gives in turn rise to a faster return on investment. It was also seen that the use of "near" end-of-life products, increased the difficulty to perform repairs. Therefore, the use of long-term service products is recommended to ensure sustainability for a longer time.
In addition, several technical solutions were shown to increase the PV system's reliability and sustainability. Lastly, the technology recommendations are added in this paper to reduce the O&M costs and to keep the PV microgrid lifetime as long as possible such as online monitoring solution, PV and battery lifetime estimation, load forecasting, and PV inverters technologies. Further research is still needed to find the optimal planning, design, operation, and maintenance while constraining costs, and how to deploy the technology to reduce the operation and maintenance costs.