Experimental Investigation of the Heat Transfer Characteristics of Plate Heat Exchangers Using LiBr/Water as Working Fluid

: In this study, the heat exchange characteristics of water–LiBr solutions used as working ﬂuid in a plate heat exchanger (PHE) were experimentally investigated at various concentrations. To analyze the heat transfer characteristics under LiBr/water conditions, a brazing type plate heat exchanger was installed, and the LiBr concentration on the high-temperature side was controlled at 56%, 58%, 60% and 60%. The results showed that the average heat transfer rate under water/water conditions was higher than that under LiBr/water conditions and the average heat transfer rate decreased as the LiBr concentration on the hot side increased. In addition, under both water/water and LiBr/water conditions, the average heat transfer rate and overall heat transfer coefﬁcient increased as the mass ﬂow rate of the working ﬂuid on the hot side increased. When LiBr was used, the Reynolds number (Re) of LiBr on the hot side was more than nine times lower than that of water at the same mass ﬂow rate owing to the inﬂuence of the increased viscosity. Based on the data obtained from the water/water and LiBr/water experiments, a correlation for predicting the Nusselt number (Nu) on the hot side in a wide range was developed.


Introduction
With the rapid global industrial and economic growth in recent years, energy consumption has been increasing worldwide, leading to intensified global warming and environmental damage. Regulations on greenhouse gas emissions have accordingly been reinforced to mitigate global warming. Various problems with respect to refrigeration and cooling systems have been identified in light of their potential environmental impact. Research on refrigeration and cooling systems is therefore essential because they directly affect the ability to maintain a pleasant living environment as well as industrial manufacturing in modern society [1]. R-12 and R-22, which are freon-based refrigerants, have traditionally been used in refrigeration systems, while nowadays the use of natural refrigerants, such as R717 and R744, as well as low-global warming potential (GWP) alternative refrigerants such as R1234yf and R1234ze, is encouraged. However, the fourth generation refrigerants, such as R1234yf and R1234ze, are more expensive than second and third generation refrigerants. In addition, natural refrigerants also have critical limitations, such as their toxicity, combustibility, and operating pressure. Therefore, continuous research on various types of refrigeration systems with low GWP is required.
Among the various refrigeration systems, absorption refrigerators are efficient in terms of their energy saving capabilities. This is because they require a relatively small amount of additional power to provide refrigeration using the latent heat of vaporization of the conditions. Kim et al. [18] analyzed the heat transfer and pressure drop according to the chevron angles of 30 • , 45 • , and 63 • , and found that the heat transfer performance increased alongside the increase in chevron angle. Kwon et al. [19] investigated the influence of various chevron angles (60 • , 120 • , and mixed type) of a solution heat exchanger on the heat transfer and pressure drop. Based on the experiment results obtained, they proposed a Nu and friction coefficient correlation according to the chevron angle. Song et al. [20] experimentally investigated the PHE performance under the operating conditions of the recovery solution heat exchanger of an absorption refrigerator. They demonstrated that the Nu correlation of the existing water-based PHEs is inappropriate for predicting Nu under the operating conditions of a triple effect absorption chiller and proposed a Nu correlation for such operating conditions. In addition, Song et al. [21] derived a Nu and friction coefficient correlation according to the high chevron angle (θ = 78.5 • ) and low chevron angle (θ = 55.7 • ) in PHEs and determined inconsistencies by applying the experimental conditions reported in previous studies.
The aforedescribed studies [10][11][12][13][14][15] were experimental studies on water/water in PHEs, and previous studies on LiBr/LiBr [17][18][19][20][21] mostly analyzed heat transfer characteristics and developed Nu correlations according to the experimental conditions. However, the water/LiBr condition of heat transfer characteristics analysis in the falling file type generator [22][23][24], which is a component of the absorption system, has been variously conducted, but studies related to water/LiBr in the simple plate heat exchanger (brazed type and gasket type plate heat exchanger) are insufficient. Because water has a higher heat transfer performance than LiBr, it can create a lower absorbent temperature through additional heat exchange with liquid LiBr present at the front end of the absorber in an absorption system, thereby improving the absorption performance in the absorber. Heat recovery for separate heating is also possible using such a device. To this end, in this study, the heat transfer characteristics and performance of a brazed plate heat exchanger were experimentally investigated under the LiBr/water condition for additional cooling inside an absorption system. In addition, the water/water experiment was performed to compare the performance, and a new Nu correlation that is related to LiBr/water heat transfer according to the mass flow rate was derived. The derived Nu correlation based on the LiBr/water experiment was compared with the Nu correlations presented in previous studies (LiBr/LiBr and water/water), and a correlation for predicting Nu under conditions with a wide range of concentration values, including both the water/water and LiBr/water experiment results, was newly derived. Figure 1a,b show the schematic diagram of the experimental setup used in this study and an actual image. The experimental setup consists of: (1) a solution tank for storing and heating LiBr and water, (2) a condenser for maintaining the concentration of the solution, (3) test PHE, (4) recovery PHE, (5) cooling PHE, and (6) a constant-temperature bath for cooling loads. In the solution tank, two 7.5-kW heaters for the preheating and concentration control of the LiBr solution and a pressure gauge (UNIK 5000, DE Druck, Boston, MA, USA) for pressure measurement were installed. (7) Solution pump was installed at a distance of 1.5 m from the front of the test PHE (DIC285-19F, Dong Il Brazing, Bucheon, South korea) to transport fluids on the hot and cold sides, and bypass lines were constructed to reduce the pump load and control the flow rate. The flow rates of the working fluids on the hot and cold sides were adjusted by employing RPM control using inverters. Resistance temperature detectors (RTDs) and differential pressure gauges (Model 230, Setra Systems, Boston, MA, USA) were installed at the inlets and outlets on the hot and cold sides to measure the heat transfer rate and differential pressure of the test PHE. In addition, (8) a mass flow meter (ALT mass type U, OVAL Corporation, Tokyo, Japan) was installed at the inlets of the test PHE on the hot and cold sides to measure the mass flow rates of the working fluids that flow in the system. The fluid on the hot side cooled in the recovery PHE is transported to the storage tank on the hot side for heating, and the fluid on the cold side heated in the recovery PHE is transported to the low-temperature storage tank after exchanging heat with the coolant supplied from the 3RT constant-temperature bath in the cooling PHE. To minimize heat loss to the outside during experiments, the heat exchangers, valves, solution tank, and piping were insulated with glass wool that has high insulation performance.

Experimental Apparatus
Energies 2021, 14, x FOR PEER REVIEW 4 of 15 was installed at the inlets of the test PHE on the hot and cold sides to measure the mass flow rates of the working fluids that flow in the system. The fluid on the hot side cooled in the recovery PHE is transported to the storage tank on the hot side for heating, and the fluid on the cold side heated in the recovery PHE is transported to the low-temperature storage tank after exchanging heat with the coolant supplied from the 3RT constant-temperature bath in the cooling PHE. To minimize heat loss to the outside during experiments, the heat exchangers, valves, solution tank, and piping were insulated with glass wool that has high insulation performance.    Table 1 show the geometry and detailed geometrical information of the test PHE used in this study.
Energies 2021, 14, x FOR PEER REVIEW 5 of 15 Figure 2 and Table 1 show the geometry and detailed geometrical information of the test PHE used in this study.  The performance of the test PHE was measured under the steady-flow condition for 15 min, and the properties of LiBr for measuring the performance of the test PHE were calculated using Engineering Equation Solver (EES) based on the measured temperature and pressure. Table 2 lists the experimental conditions used in the heat exchange experiment with water and LiBr. The inlet fluid temperatures on the cold and hot sides were fixed at 40 °C and 80 °C, respectively.   The performance of the test PHE was measured under the steady-flow condition for 15 min, and the properties of LiBr for measuring the performance of the test PHE were calculated using Engineering Equation Solver (EES) based on the measured temperature and pressure. Table 2 lists the experimental conditions used in the heat exchange experiment with water and LiBr. The inlet fluid temperatures on the cold and hot sides were fixed at 40 • C and 80 • C, respectively.
Water was used as a working fluid on the cold side. In this instance, the mass flow rate was fixed at 300 kg/h. Water and LiBr were used as a working fluid on the hot side, and the mass flow rate varied from 200 to 700 kg/h. When the working fluid on the hot side was LiBr, the concentration of LiBr was varied from 56% to 62%. of the heat transfer rates on the cold and hot sides. The heat transfer rates on the hot and cold sides can be expressed using Equations (1) and (2) as follows: In addition, the overall heat transfer coefficient (U) in PHEs can be expressed by Equation (3). In this instance, the logarithmic mean temperature difference (∆T LMTD ) that was used is given by Equation (4) [25]: where A t is the effective heat exchange area of PHE (A t = ∅L w LN ch ), which is calculated using the heat transfer plate width (L w ), port-to-port distance (L), number of channels (N ch ), and expansion coefficient (φ). The expansion coefficient (φ) can be calculated using Equation (5) [26]: In general, Nu is defined by Equation (6) in single-phase flow. It is generally expressed as Equation (7) by empirical similarity: where D h is hydraulic diameter [21]. In this study, the Nu correlation was calculated using the Wilson plot method [27], and the constant C used in Equation (7) was fixed at 1/3 [28]. Table 3 shows the detailed specifications of the measuring devices used in this study. Based on the measuring devices, the uncertainties of the thermal conductivity, convective heat transfer coefficient, and Nu be consistent using italics or not for this symbol obtained in the experiment were calculated. The experiment was performed at least three times under the same experimental conditions, and the average values were used to confirm the data. The general formula for the uncertainties of these values can be expressed as in Equation (8), and the uncertainties of the heat transfer rate, convective heat transfer coefficient, and Nu obtained in this study are shown in Table 4 [29]. In addition, the energy balance was investigated by calculating the heat gain and heat loss of the fluids on the hot and cold sides, which exchanged heat in the test PHE. When the energy balance on the hot and cold sides was examined under all conditions, the maximum error was found to be ±2.5%, indicating a relatively accurate energy transfer rate.  Table 4. Uncertainties of measurements.

Measurements Uncertainty
Heat transfer rate ±2.4% Heat transfer coefficient ±1.76% Nusselt number ±3.37% Figure 3 shows the heat transfer rate and heat transfer rate decrement ratio of LiBr/water compared to water/water according to the mass flow rate on the hot side. When the fluid on the hot side was water, the heat transfer rate increased from 7.56 to 12.13 kW as the mass flow rate increased from 200 to 700 kg/h. However, when the fluid on the hot side was a LiBr solution, the heat transfer rate decreased. In addition, the heat transfer rate decreased as the LiBr concentration increased, and the heat transfer rate was lowest when the concentration was 62%. At a mass flow rate of 200 kg/h, as the LiBr concentration increased from 56% to 62%, the heat transfer rate decreased from 4.19 to 3.8 kW, which is 44.5-49.6% lower compared with that of water. In contrast, at a mass flow rate of 700 kg/h, as the LiBr concentration increased from 56% to 62%, the heat transfer rate decreased from 9.49 to 8.88 kW, which were 21.7-26.8% lower compared with that of water. An increase in the mass flow rate of the working fluid increases the dependence on the heat transfer by the kinetic momentum of the fluid compared to the heat transfer that results from thermal diffusion during heat exchange by increasing the velocity of the fluid and the intensity of turbulence inside the PHE; thus, there is a decrease in the difference in heat transfer rate between water and LiBr.    Figure 5 shows the Nu value of LiBr/water and water/water according to the mass flow rate on the hot side. In the water/water experiment, Nu increased from 13.91 to 33.39 as the mass flow rate increased from 200 to 700 kg/h. However, at 62% LiBr, which was  Figure 4 shows the overall heat transfer coefficient and overall heat transfer coefficient decrement ratio of LiBr/water heat transfer compared to water/water according to the mass flow rate on the hot side in the water/water and LiBr/water experiments. When the working fluid on the hot side was water, the overall heat transfer coefficient increased from 1.38 to 2.03 kW/m 2 · • C as the mass flow rate increased from 200 to 700 kg/h. When 56% LiBr was used as the working fluid on the hot side, the overall heat transfer coefficient increased from 0.76 to 1.43 kW/m 2 · • C as the mass flow rate increased from 200 to 700 kg/h, which is 29.7% to 44.6% lower compared to water/water. When the highest concentration of 62% LiBr was used, the overall heat transfer coefficient increased from 0.637 to 1.177 kW/m 2 · • C as the mass flow rate increased from 200 to 700 kg/h, which is 42.1-53.7% lower compared to water/water. The experiment results showed that the overall heat transfer coefficient decreased as the LiBr concentration increased. An increase in the LiBr concentration in PHEs results in a lower Re owing to the increase in the viscosity of the working fluid, and the reduced Re decreases convective heat transfer and makes thermal diffusion difficult, thereby reducing the overall heat transfer coefficient of LiBr compared to water. Figure 5 shows the Nu value of LiBr/water and water/water according to the mass flow rate on the hot side. In the water/water experiment, Nu increased from 13.91 to 33.39 as the mass flow rate increased from 200 to 700 kg/h. However, at 62% LiBr, which was the highest concentration in the LiBr/water heat exchange, Nu increased from 6.51 to 15.1 as the mass flow rate increased from 200 to 700 kg/h. In the LiBr/water heat exchange, an increase in LiBr concentration caused a decrease in Nu, resulting in values that were 46 to 60% lower compared to the Nu value of water/water at the same flow rate. In addition, when the lowest concentration of 56% LiBr was compared with the highest concentration of 62% LiBr, the difference in Nu between the two concentrations tended to slowly increase as the mass flow rate increased. This is because variations in thermal properties with concentration led to changes in the convective heat transfer performance by turbulence or diffusion even though it had the same heat transfer plate geometry.   Figure 5 shows the Nu value of LiBr/water and water/water according to the mass flow rate on the hot side. In the water/water experiment, Nu increased from 13.91 to 33.39 as the mass flow rate increased from 200 to 700 kg/h. However, at 62% LiBr, which was   LiBr/water of this study Water/water of this study Roetzel et al. [27] Donowski and Kandlikar. [28] Focke et al. [29] Longo and Zilio. [30] aulated Nu +10% For PHEs, Nu varies depending on the geometry of heat transfer plates, flow conditions, and fluid characteristics. Various Nu correlations have been developed in previous studies. In this study, the suitability of the existing empirical formulas was determined by comparing the Nu correlations developed in previous LiBr/LiBr and water/water experiments with the results of the LiBr/water experiment. Figure 6 compares the Nu results obtained from the LiBr/water experiment with those derived from previous water/water experiments. In addition, the previous correlations used for the suitability of the experi-ment results in this study are shown in Table 5. When the LiBr/water experimental values of this study were substituted into the Nu correlation developed by Roetzel et al. [30], Nu ranged from 8.97 to 24.79. These values were significantly higher compared to the Nu results based on the LiBr/water experiment in this study, which ranged from 6.51 to 17.93. The PHE used in Roetzel et al. [30] with a heat transfer plate length of 176.5 mm, a width of 71 mm, a heat transfer plate thickness of 0.5 mm, and a chevron height of 2 mm had similar geometry to the heat exchanger used in this study. However, the chevron angles were significantly different; 60 • was used in this study and 20 • was used in Roetzel et al. [30]. In general, the constant A in the empirical formula for Nu (Equation (7)) is determined by the heat transfer plate geometry. Therefore, there was a large difference in constant A between Roetzel et al. [30] (0.371) and the value in this study (0.28 to 0.324). In addition, when the LiBr/water experimental values were substituted into the Nu correlations presented in previous studies [30][31][32][33], all of the correlations predicted values that were higher than the Nu results in this study. In particular, the formula presented by Donowski and Kandlikar [31] predicted the highest value, and that presented by Focke et al. [32] exhibited the smallest error. Because the constants B and C in the empirical formula for Nu reflect the flow characteristics and thermal properties of the heat exchange medium, the difference in the value of each constant is caused by the difference in each experimental condition. As a result of comparing the Nu number correlation between the water/water in previous study and LiBr/water in this study, the B values of the Equation (7) were quite different. The B values of the LiBr/water condition in this study was 0.644-0.677, whereas the B values in previous studies [30][31][32][33] was 0.703 to 0.78. It was confirmed that the maximum difference of B value was 0.136. The shape of the plate heat exchanger used in previous studies was different from that in this study, but it was confirmed that the influence of thermal properties of the working fluid on the B value was relatively larger than the influence of shape of the plate heat exchanger. Therefore, when the Nu of LiBr/water was predicted through the correlations in previous studies developed through water/water experiments, the error rate exceeded 10%, confirming that there are limitations with respect to directly applying the correlations.    LiBr/water of this study

-10%
Water/water of this study Roetzel et al. [27] Donowski and Kandlikar. [28] Focke et al. [29] Longo and Zilio. [30] Calaulated Nu Experimental Nu +10% Figure 6. Comparisons of Nu of this study based on LiBr/water with existing Nu correlations of water/water.    Tables 6 and 7 show the detailed geometrical information of PHE and experimental conditions in the previous studies. Because LiBr is generally used in absorption systems, it is difficult to make a direct comparison with the heat exchange results of LiBr/water. However, to the best of our knowledge, no extant study has investigated the difference, and it is therefore considered useful to examine the difference through this study. When the existing correlations based on LiBr/LiBr were compared with the LiBr/water results of this study, Kwon et al. [19] exhibited large errors of less than 60%, Song et al. [21] less than 30%, and Kim et al. [18] less than 50%. While Kim et al. [18] and Song et al. [21] showed tendencies similar to that of this study, despite the large errors in Nu, Kwon et al. [19] exhibited a significantly different increasing tendency for Nu compared to the results of this study. These differences occurred because experiments were performed at higher inlet temperatures in the previous studies compared to this study, and the previous studies had lower Nu results at similar Re levels as they had lower Prandtl numbers (Pr). In addition, Nu decreased because different geometrical parameters, such as the chevron angle, pitch, and height, cause a significant difference in the turbulence intensity of the secondary flow at the heat transfer plate contact point. As a result of comparing with Song et al. [21], there was no significant difference in the B values in Equation (7). The working fluid used in Song et al. [21] was LiBr/LiBr solution with a B value of 0.676. Also, the high-side working fluid under the LiBr/water condition in this study was a LiBr solution with B values of 0.644-0.677. In comparing B values, they were almost similar with a maximum difference of 0.03. On the other hand, since the shape of the plate heat exchanger used in this experiment and previous study [21] are different, the A values in Equation (7) were quite different. The A values in this study were ranged from 0.28 to 0.32, and that in the  Tables 6 and 7 show the detailed geometrical information of PHE and experimental conditions in the previous studies. Because LiBr is generally used in absorption systems, it is difficult to make a direct comparison with the heat exchange results of LiBr/water. However, to the best of our knowledge, no extant study has investigated the difference, and it is therefore considered useful to examine the difference through this study. When the existing correlations based on LiBr/LiBr were compared with the LiBr/water results of this study, Kwon et al. [19] exhibited large errors of less than 60%, Song et al. [21] less than 30%, and Kim et al. [18] less than 50%. While Kim et al. [18] and Song et al. [21] showed tendencies similar to that of this study, despite the large errors in Nu, Kwon et al. [19] exhibited a significantly different increasing tendency for Nu compared to the results of this study. These differences occurred because experiments were performed at higher inlet temperatures in the previous studies compared to this study, and the previous studies had lower Nu results at similar Re levels as they had lower Prandtl numbers (Pr). In addition, Nu decreased because different geometrical parameters, such as the chevron angle, pitch, and height, cause a significant difference in the turbulence intensity of the secondary flow at the heat transfer plate contact point. As a result of comparing with Song et al. [21], there was no significant difference in the B values in Equation (7). The working fluid used in Song et al. [21] was LiBr/LiBr solution with a B value of 0.676. Also, the high-side working fluid under the LiBr/water condition in this study was a LiBr solution with B values of 0.644-0.677. In comparing B values, they were almost similar with a maximum difference of 0.03. On the other hand, since the shape of the plate heat exchanger used in this experiment and previous study [21] are different, the A values in Equation (7) were quite different.
The A values in this study were ranged from 0.28 to 0.32, and that in the Song et al. [21] were 0.244, which indicating a relatively large difference with a maximum difference of 0.08. The B value was similar because the working fluid was the same as LiBr as hot-side working fluid, but the A value was differ due to the difference in the shape of the plate heat exchanger. A comprehensive analysis confirmed that it is somewhat difficult to predict the Nu of LiBr/water using the empirical formulas based on water/water [31][32][33] and LiBr/LiBr [18,19,21] presented in the previous studies. Therefore, it is necessary to develop a separate Nu correlation to identify Nu in the LiBr/water heat exchange process. In particular, the influence of geometry and working fluid must be accurately determined to predict the Nu of LiBr/water with high accuracy through the relatively easy water/water experiment. To this end, in this study, parameters A and B in the empirical formula for Nu were analyzed and functionalized according to variations in concentration by performing experiments. A and B are the empirical constants of Nu = ARe B Pr C presented in Equation (7).  Table 8 shows the results of A and B, which are the main parameters of the Nu correlation developed according to the LiBr concentration in LiBr/water heat exchange. As the LiBr concentration on the hot side increased from 56% to 62%, parameter A increased from 0.28 to 0.324, but parameter B decreased from 0.677 to 0.644. In general, the mass flow rate of the working fluid and the concentration of LiBr are closely correlated to Re and Pr, which determine Nu. Because LiBr has a lower thermal diffusivity than water, the influence of the momentum of the fluid on convective heat transfer in PHE increases. Owing to the increasing influence of the PHE geometry, there is an increase in parameter A, which is directly related to the PHE geometry. In addition, when the concentration of LiBr increases, the degree of increase in Re due to the increase in mass flow rate decreases. This is because the viscosity increases owing to the increase in LiBr concentration; therefore, parameter B decreases. In this study, parameters A and B are closely associated with the determination of Nu according to the LiBr concentration. Equation (9) shows the correlation for predicting Nu in LiBr/water heat exchange according to the LiBr concentration, which was developed in this study based on the water/water data. The developed correlation is applicable in the 221.1 < Re < 872.2 and 2.46 < Pr < 2.79 ranges under water/water condition: Figure 8 depicts the error of the developed correlation compared to the experiment results obtained for LiBr/water. When the predicted Nu was compared with the experimental Nu, the error of 60% LiBr/water was 0.36% at a mass flow rate of 700 kg/h on the hot side, indicating high accuracy. At a flow rate of 200 kg/h, 58% LiBr/water exhibited the largest error of 2.15%. In addition, 58% LiBr/water showed the smallest error for Nu in the entire flow rate range, and 62% LiBr/water exhibited relatively large errors.
Energies 2021, 14, x FOR PEER REVIEW 13 of 15 Figure 8 depicts the error of the developed correlation compared to the experiment results obtained for LiBr/water. When the predicted Nu was compared with the experimental Nu, the error of 60% LiBr/water was 0.36% at a mass flow rate of 700 kg/h on the hot side, indicating high accuracy. At a flow rate of 200 kg/h, 58% LiBr/water exhibited the largest error of 2.15%. In addition, 58% LiBr/water showed the smallest error for Nu in the entire flow rate range, and 62% LiBr/water exhibited relatively large errors.

Conclusions
In this study, the LiBr/water heat exchange characteristics in a plate heat exchanger (PHE) were experimentally analyzed, and a correlation for predicting the Nusselt number (Nu) during LiBr/water heat exchange was derived based on the water/water experiment results. The experimental results showed that the heat transfer rate and overall heat transfer coefficient decreased in LiBr/water heat exchange compared to water/water heat exchange, and they further decreased as the LiBr concentration increased. As the mass flow rate on the hot side increased from 200 to 700 kg/h, the heat transfer rate of water increased from 7.56 to 12.13 kW, but that of 62% LiBr increased from 3.8 to 8.88 kW, which were up to 26.8% lower compared to the case of using water. In addition, when the mass flow rate on the hot side increased from 200 to 700 kg/h, the overall heat transfer coefficient of water increased from 1.38 to 2.03 kW/m 2 •°C, but that of 62% LiBr increased from 0.637 to 1.177 kW/m 2 •°C, which were 42.1 to 53.7% lower compared to water.
When variations in Nu with LiBr concentration were examined and the average Nu decrement ratio was found to have increased to 7.19%, 12.12% and 17.32% as the LiBr concentration increased from 56% to 58%, 60%, and 62%, respectively. This is because changes in the properties of LiBr caused by the change in the LiBr concentration affected the heat transfer by heat transfer plate geometry, momentum, and thermal diffusion. In

Conclusions
In this study, the LiBr/water heat exchange characteristics in a plate heat exchanger (PHE) were experimentally analyzed, and a correlation for predicting the Nusselt number (Nu) during LiBr/water heat exchange was derived based on the water/water experiment results. The experimental results showed that the heat transfer rate and overall heat transfer coefficient decreased in LiBr/water heat exchange compared to water/water heat exchange, and they further decreased as the LiBr concentration increased. As the mass flow rate on the hot side increased from 200 to 700 kg/h, the heat transfer rate of water increased from 7.56 to 12.13 kW, but that of 62% LiBr increased from 3.8 to 8.88 kW, which were up to 26.8% lower compared to the case of using water. In addition, when the mass flow rate on the hot side increased from 200 to 700 kg/h, the overall heat transfer coefficient of water increased from 1.38 to 2.03 kW/m 2 · • C, but that of 62% LiBr increased from 0.637 to 1.177 kW/m 2 · • C, which were 42.1 to 53.7% lower compared to water.
When variations in Nu with LiBr concentration were examined and the average Nu decrement ratio was found to have increased to 7.19%, 12.12% and 17.32% as the LiBr concentration increased from 56% to 58%, 60%, and 62%, respectively. This is because changes in the properties of LiBr caused by the change in the LiBr concentration affected the heat transfer by heat transfer plate geometry, momentum, and thermal diffusion. In addition, a correlation for predicting Nu in LiBr/water heat exchange was developed (Equation (9)) based on the water/water heat transfer data. When the developed correlation was compared with the Nu results obtained through experiments, the error was found to be less than ±2.5% under all conditions.