A Modified Grid-Connected Inverter Topology for Power Oscillation Suppression under Unbalanced Grid Voltage Faults

Under unbalanced grid voltage faults, the output power oscillation of a grid-connected inverter is an urgent problem to be solved. In the traditional topology of inverters, it is impossible to eliminate power oscillation and simultaneously maintain balanced output current waveform. In this paper, considering the solvability of reference current matrix equation, the inherent mechanism of inverter output power oscillation is analyzed, and a modified topology with auxiliary modules inserted in series between the inverter output filter and the point of common coupling (PCC) is proposed. Due to the extra controllable freedoms provided by auxiliary modules, the inverter could generate extra voltage to correct PCC voltage while keeping balance of output current, so as to eliminate the oscillation of output power. Simulation and experimental results verify the effectiveness of the proposed topology.


Introduction
The grid-connected inverter is the vital interface module for distributed generation (DG) systems, including wind power generation, photovoltaic power generation, to be connected to the grid. It can directly determine the value and direction of current and power and is crucial for the safe operation of the grid [1,2]. Small and medium-sized DG systems are often connected to the grid through the power distribution network. However, due to the abnormal weather conditions, large load switching on-off, insulation failure, human error and so on, voltage faults often occur in the power distribution network. Most of voltage faults can be attributed to the asymmetric faults of grid voltage, for example, the unbalanced voltage fault caused by single-phase grounding is a representative type [3]. In the case of asymmetric faults, the grid-connected inverter is required to have the low voltage ride through (LVRT) capability so as to avoid the chain reaction of DGs disconnection with the grid [4,5]. When the voltage at the point of common coupling (PCC) drops, grid code requires the inverter to keep connecting with the grid for a certain period of time [3]. At the same time, the grid-connected inverter should have the power transmission capacity under abnormal voltage at PCC [1,6]. Under unbalanced PCC voltage, the traditional current closed-loop control strategy which only controls positive-sequence current in essence will cause output power oscillation so as to enlarge the voltage ripple of DC side bus and damage the output current quality [6][7][8][9]. To enhance the performance of inverters, it is necessary to eliminate the output power oscillation of grid-connected inverters under unbalanced PCC voltage.
At present, the main methods to eliminate the output power oscillation of gridconnected inverter under unbalanced grid voltage can be divided into two categories: the first type is to improve the control strategy; the second one is to change the topology of the inverter. In [6,10,11], different proportions of negative-sequence current is added to the current reference to decrease power oscillation. The main problem is that the output current has difficulty meeting the requirements of grid codes, and there may be risk of current overrun. In [12,13], the power reference is modified by considering the upper current limit value of switch tube to guarantee that the output current will not exceed the maximum allowable value. However, the waveform of the output current is seriously distorted. A positive and negative-sequence conductance and susceptance control scheme is proposed in [14]. By optimizing the value of negative-sequence conductance, the peak value of the output current can be controlled, but the power oscillation is not effectively reduced. The second type of strategy is to eliminate the power oscillation by changing the topology of the inverter. In [15], a three-phase four-wire system with zero-sequence current channel is proposed. The introduction of zero-sequence current increases the controllable quantity of the system, which is conducive to eliminating power oscillation and improving current quality. Nevertheless, the power oscillation still exists when adopting the current closedloop control strategy. In one word, the reference current matrix equation of grid-connected inverter in the topologies mentioned above cannot meet the solvability condition, which is the essential reason that the power oscillation could not be eliminated while the current waveform is balanced.
In this paper, a modified grid-connected inverter topology with auxiliary modules inserted in series between PCC and the output filter of each phase is proposed, which could increase the controllable freedoms of reference current equation of inverter so as to make the reference current equation of the inverter meet the solvability condition. Then, the oscillation of the output power is eliminated, and the negative-sequence current is avoided to be injected into power grid simultaneously. The simulation and experimental results are presented to verify the effectiveness of the modified topology.

Relationship between Power Oscillation and Grid Voltage in Traditional Topology
Typical grid voltage faults can be divided into seven categories [16], most of them are asymmetric faults. Unbalanced voltage fault caused by single-phase grounding is a representative one [3]. The unbalanced voltage at PCC will cause the oscillation of output power and the distortion of output current, which will affect the safe operation of the grid-connected inverters [11].

Relationship among Output Current, Power Oscillation and Unbalanced Voltage
The traditional control strategy of grid-connected inverters under unbalanced grid voltage can be summarized as a unified control strategy [10,11,17], which uses different values of adjustment coefficient (−1 ≤ k ≤ 1) to reflect different control strategies, as shown in Table 1. No matter what control strategy is used, it is always difficult to achieve the optimal output current and power at the same time. A quantitative numerical analysis is given as follows.  (1). Numerical analysis of output current Since there is no zero-sequence current component channel in the three-phase threewire power distribution network, the voltage at PCC and output current can be expressed in Equation (1): where U + , U − and U 0 are the amplitudes of positive, negative and zero-sequence components of the voltage, I + and I − are the amplitudes of positive and negative-sequence components of output current, θ vp , θ vn and θ 0 are the initial phase angles of positive, negative and zero-seqence components of the voltage, θ ip and θ in are the initial phase angles of positive, negative-sequence component of output current and ω is the angular frequency of the voltage, respectively. When the three-phase inverter is connected to the grid, the current reference value is shown in Equations (3) and (4) [12].
where P* and Q* are the reference values of active power and reactive power, respectively.
After transformation to abc coordinate system, Equations (5)-(7) are obtained, where, When three-phase inverter is in grid-connected operation state, the current closed-loop control strategy is often used [8], so the output current could accurately track the reference value. The maximum value of output current is given as Equation (8): It can be seen from Equations (5)-(7) that the amplitudes and phase angles of threephase currents are related to the amplitudes of positive and negative-sequence voltages, initial phase angles of positive and negative-sequence voltages, power reference value and adjustment coefficient k. To ensure that the output current of grid-connected inverters meets the grid codes [18,19], the only way is to set the adjustment coefficient k as 0, which means to use the balanced positive sequence control (BPSC) strategy [20].
According to Equation (8), when the parameters of Table 2 are adopted, the relationship between the maximum value of output current amplitude and the adjustment coefficient k is shown in Figure 1. When k changes from −1 to 1, the maximum value of output current amplitude decreases firstly and then increases, and the BPSC control method, which means k as 0, can ensure that the current stress of the inverter is minimum under the same power.
(2). Analysis of power oscillation According to the instantaneous power theory, the active power and reactive power can be expressed as Equations (9) and (10): where u α and u β are the αβ axis components of the PCC voltage, respectively. When expanding Equations (9) and (10), the quadratic term is the fluctuating power, as shown in Equations (11) and (12): When the parameters shown in Table 2 are adopted, the relationship between the power oscillation value and the adjustment coefficient k is shown in Figure 2. When k changes from −1 to 1, the oscillation value of output power can reach 0.4 p.u. at most. The change trend of active power oscillation value is just opposite to that of reactive power oscillation value. It is impossible to make active power oscillation value and reactive power oscillation value minimal at the same time by changing k. When BPSC is used, the oscillation value of active power and reactive power can reach 0.2 p.u., which means that the oscillation of output power is not eliminated.  changes from to 1, the oscillation value of output power can reach 0.4 p.u. at most. The change trend of active power oscillation value is just opposite to that of reactive power oscillation value. It is impossible to make active power oscillation value and reactive power oscillation value minimal at the same time by changing k. When BPSC is used, the oscillation value of active power and reactive power can reach 0.2 p.u., which means that the oscillation of output power is not eliminated.   The variation of k represents different control strategies. The power oscillation cannot be eliminated by just changing the control strategy when the topology is not optimized. The next section will give a strict theoretical proof. changes from to 1, the oscillation value of output power can reach 0.4 p.u. at most. The change trend of active power oscillation value is just opposite to that of reactive power oscillation value. It is impossible to make active power oscillation value and reactive power oscillation value minimal at the same time by changing k. When BPSC is used, the oscillation value of active power and reactive power can reach 0.2 p.u., which means that the oscillation of output power is not eliminated.   The variation of k represents different control strategies. The power oscillation cannot be eliminated by just changing the control strategy when the topology is not optimized. The next section will give a strict theoretical proof. The variation of k represents different control strategies. The power oscillation cannot be eliminated by just changing the control strategy when the topology is not optimized. The next section will give a strict theoretical proof.

Deficiency of Traditional Inverter Topology
After Clark transformation, Equation (1) can be written as Equation (13): where Three-phase output currents can be written as Equation (14): where The instantaneous output power is given as Equation (15): where P 0 is the DC component value of active power, P c2 and P s2 are the coefficients of cosine and sinusoidal terms for the second oscillation value of active power, Q 0 is the DC component value of reactive power, Q c2 and Q s2 are the coefficients of cosine and sinusoidal terms for the second oscillation value of reactive power. P 0 , P c2 , P s2 , Q 0 , Q c2 and Q s2 can be expressed by matrix as Equation (16): where When the output current meets the grid codes [18,19], the negative-sequence current should be set as zero, then Equation (16) will be changed into Equation (17): In Equation (16), the rank of the coefficient matrix is 4, the rank of the augmented matrix is 5. The rank of the coefficient matrix is not equal to the rank of the augmented matrix, so Equation (16) has no solution. This is the reason why the control strategy in [10][11][12][13][14] has difficulty eliminating the power oscillation.
In Equation (17), the rank of the coefficient matrix is 2, the rank of the augmented matrix is 3. The rank of the coefficient matrix is not equal to the rank of the augmented matrix, so Equation (17) has no solution. This is the reason why the BPSC control strategy has difficulty eliminating power oscillation for the traditional topology.
In the same way, it can be found that after adding a zero-sequence component in [15], Equation (17) where v 0 Re , v 0 Im are the real and imaginary components of zero-sequence voltage at PCC, i 0 Re , i 0 Im are the real and imaginary components of zero-sequence output current, the detailed definition refers to [15].
In (18), the rank of the coefficient matrix is 4, the rank of the augmented matrix is 5. The rank of the coefficient matrix is not equal to the rank of the augmented matrix, so Equation (18) has no solution. This is the reason why the BPSC control strategy has difficulty eliminating power oscillation for three-phase four-wire inverter in [15].

Principle and Advantages of Modified Topology for Grid-Connected Inverter
According to the discussion in Section 2, the reason why the traditional topology is incapable of eliminating the power oscillation is that the number of controllable free variables is small, which leads to the mismatch between the order of the current reference coefficient matrix and the order of the augmented matrix. From the point of view on hardware, the number of controllable variables in the current reference equation can be increased by changing the topology structure, so that the equation can meet the solvability conditions.

Modified Topology of Grid-Connected Inverters
The proposed topology of grid-connected inverter is shown in Figure 3. The auxiliary modules are inserted in series between the output filter of inverter (the points a 1 , b 1 and c 1 in Figure 3a) and PCC (the points a 2 , b 2 and c 2 in Figure 3a). The three-phase auxiliary modules are independent of each other and can be separately controlled. Figure 3b shows the detailed internal block diagram of the auxiliary module which is essentially a single-phase inverter. Ladd and Cadd constitute the output filter circuit of the auxiliary module to filter the switching subharmonics in the circuit. Radd is the damping resistance of the output filter circuit to prevent the possible oscillation of the LC filter circuit. For the voltages at PCC1, Equation (19) could be obtained as:  are the output voltages of auxiliary modules in phases A, B and C, respectively.
Accordingly, Equation (17) can be changed into Equation (20): The three-phase auxiliary modules are independent of each other and can be separately controlled. Figure 3b shows the detailed internal block diagram of the auxiliary module which is essentially a single-phase inverter. L add and C add constitute the output filter circuit of the auxiliary module to filter the switching subharmonics in the circuit. R add is the damping resistance of the output filter circuit to prevent the possible oscillation of the LC filter circuit. For the voltages at PCC 1 , Equation (19) could be obtained as: where ∆v a , ∆v b and ∆v c are the output voltages of auxiliary modules in phases A, B and C, respectively. Accordingly, Equation (17) can be changed into Equation (20): where ∆v + d , ∆v + q are the positive-sequence dq axis components of ∆v a , ∆v b and ∆v c ; ∆v − d , ∆v − q are the negative sequence dq axis components of ∆v a , ∆v b and ∆v c after positive and negative-sequence separation and Park transformation.
When the output of the auxiliary module is set to satisfy Equation (21): a new equation, Equation (22) can be obtained from Equation (20): It can be further simplified as Equation (23): The coefficient matrix rank of Equation (23) is 2, the rank of the augmented matrix is 2. The number of equations is equal to the number of variables, so that Equation (23) has a unique solution. The corresponding current reference value can be solved as Equation (24): When it is needed to limit the current, the upper limit of the reference current can be adjusted by changing the value of ∆v + d and ∆v + q in Equation (21). The overall control structure of the system is shown in  The Decoupled Double Synchronous Reference Frame Phase-Locked Loop (DDSRF-PLL), which has better performance under unbalanced voltage, is adopted to achieve phase detection [21]. The structure of DDSRF-PLL is shown in Figure 5. After positive and negative sequence abc/dq transformation,  The Decoupled Double Synchronous Reference Frame Phase-Locked Loop (DDSRF-PLL), which has better performance under unbalanced voltage, is adopted to achieve phase detection [21]. The structure of DDSRF-PLL is shown in Figure 5. After positive and negative sequence abc q after a decoupling network. Similar to the phase detection principle of the Synchronous Reference Frame Phase-Locked Loop (SRF-PLL) [21], the phase of the systemθ could be obtained by making v + * q approach zero through the PI controller. The detailed structure of decoupling network is expressed as in [21]. * q v + approach zero through the PI controller. The detailed structure of decoupling network is expressed as in [21].

Advantages of Modified Topology
The voltage and current vector trajectories of the traditional topology and the modified topology are shown in Figure 6 [9], respectively. When single-phase voltage fault occurs, the trajectory of voltage vector will be distorted. When the voltage vector trajectory shows a spindle-shaped variation, as the trajectory of Utra in Figure 6, in order to keep the output power constant, the trajectory of the current amplitude becomes an ellipse, as the trajectory of Itra in Figure 6. Where, Imax is the maximum value of the allowable current amplitude of the system. It can be seen that the amplitude of Itra has exceeded the value of Imax near the long axis of the actual current track, as shown in the shaded area, which may give rise to over-current fault. When the auxiliary modules are inserted into the system, the unbalanced voltage is corrected to a standard circle, as the trajectory of Umod in Figure 6, and the corresponding current amplitude trajectory is also a standard circle, as the trajectory of Imod in Figure 6. Since the amplitude of Umod can be adjusted by changing the value of d v +  and q v +  , so that the radius of the trajectory of Umod can be ensured not to be too small, then the corresponding trajectory of Imod can be guaranteed to be included

Advantages of Modified Topology
The voltage and current vector trajectories of the traditional topology and the modified topology are shown in Figure 6 [9], respectively. When single-phase voltage fault occurs, the trajectory of voltage vector will be distorted. When the voltage vector trajectory shows a spindle-shaped variation, as the trajectory of U tra in Figure 6, in order to keep the output power constant, the trajectory of the current amplitude becomes an ellipse, as the trajectory of I tra in Figure 6. Where, I max is the maximum value of the allowable current amplitude of the system. It can be seen that the amplitude of I tra has exceeded the value of I max near the long axis of the actual current track, as shown in the shaded area, which may give rise to over-current fault. When the auxiliary modules are inserted into the system, the unbalanced voltage is corrected to a standard circle, as the trajectory of U mod in Figure 6, and the corresponding current amplitude trajectory is also a standard circle, as the trajectory of I mod in Figure 6. Since the amplitude of U mod can be adjusted by changing the value of ∆v + d and ∆v + q , so that the radius of the trajectory of U mod can be ensured not to be too small, then the corresponding trajectory of I mod can be guaranteed to be included in the circular trajectory of I max , so as to avoid the risk of overcurrent fault.
fied topology are shown in Figure 6 [9], respectively. When single-phase voltage fault occurs, the trajectory of voltage vector will be distorted. When the voltage vector trajectory shows a spindle-shaped variation, as the trajectory of Utra in Figure 6, in order to keep the output power constant, the trajectory of the current amplitude becomes an ellipse, as the trajectory of Itra in Figure 6. Where, Imax is the maximum value of the allowable current amplitude of the system. It can be seen that the amplitude of Itra has exceeded the value of Imax near the long axis of the actual current track, as shown in the shaded area, which may give rise to over-current fault. When the auxiliary modules are inserted into the system, the unbalanced voltage is corrected to a standard circle, as the trajectory of Umod in Figure 6, and the corresponding current amplitude trajectory is also a standard circle, as the trajectory of Imod in Figure 6. Since the amplitude of Umod can be adjusted by changing the value of d v +  and q v +  , so that the radius of the trajectory of Umod can be ensured not to be too small, then the corresponding trajectory of Imod can be guaranteed to be included in the circular trajectory of Imax, so as to avoid the risk of overcurrent fault.

Capacity Design of Auxiliary Modules
Supposing that the fault occurs in phase B, and the voltage amplitude of phase B is β times of its original normal value, then the vector format of three-phase voltage is described as Equation (25): The positive, negative and zero-sequence voltage components of phase A are obtained as Equation (26), [21].
The positive, negative and zero-sequence voltage components of phase B and phase C are obtained as Equations (27) and (28): In the modified topology, the average powers of the three auxiliary modules are shown in Equation (29): When β changes between [0, 1], the power curve of the auxiliary module is shown in Figure 7. Auxiliary module of the fault phase-phase B essentially injects power into the circuit. When the output power of the grid-connected inverter is used as the power base value, which is P base = (3/2)V I, the maximum value of the injected power is 0.22 p.u. (β = 0). Phases A and C are non-fault phases. Their auxiliary modules absorb power from the circuit, and the maximum absorbed power is 0.11 p.u. (β = 0). Therefore, for the single-phase voltage fault, the power capacity of the auxiliary module designed above 0.22 p.u. can meet the requirements no matter what the drop depth is and no matter which phase the fault occurs in. According to the clearing time of inverters under voltage faults shown in Figure 8, in case of voltage drop, the grid-connected inverter only needs to maintain the connection time of 2s at most. Therefore, the energy needed to be absorbed or released by the auxiliary module will not be too large, and the operation of the inverter during the LVRT period will not cause damage to the energy storage devices in the auxiliary module.

Stability Analysis of the Modified Topology
Since the parameters of the three branches of the inverter are identical, according to [7,22], the whole system can be simplified shown in Figure 9.
In Figure 9, * v is the output voltage reference of the auxiliary module, is are the reference current and output current of system, respectively, and their detailed form are expressed as [22].
When we adopt the parameters in Tables 3-5, the pole-zero maps of the current closed transfer functions for the traditional topology and the modified topology are shown in Figure 10, respectively. In Figure 10 According to the clearing time of inverters under voltage faults shown in Figure 8, in case of voltage drop, the grid-connected inverter only needs to maintain the connection time of 2 s at most. Therefore, the energy needed to be absorbed or released by the auxiliary module will not be too large, and the operation of the inverter during the LVRT period will not cause damage to the energy storage devices in the auxiliary module. According to the clearing time of inverters under voltage faults shown in Figure 8, in case of voltage drop, the grid-connected inverter only needs to maintain the connection time of 2s at most. Therefore, the energy needed to be absorbed or released by the auxiliary module will not be too large, and the operation of the inverter during the LVRT period will not cause damage to the energy storage devices in the auxiliary module.

Stability Analysis of the Modified Topology
Since the parameters of the three branches of the inverter are identical, according to [7,22], the whole system can be simplified shown in Figure 9.
In Figure 9, * v is the output voltage reference of the auxiliary module, is are the reference current and output current of system, respectively, and their detailed form are expressed as [22].
When we adopt the parameters in Tables 3-5, the pole-zero maps of the current closed transfer functions for the traditional topology and the modified topology are shown in Figure 10, respectively. In Figure 10, p1 and p2 are the dominant closed-loop poles of the current transfer function for the traditional topology and the modified topol-

Stability Analysis of the Modified Topology
Since the parameters of the three branches of the inverter are identical, according to [7,22], the whole system can be simplified shown in Figure 9.
In Figure 9, v * is the output voltage reference of the auxiliary module, G add (s) is the transfer function of the auxiliary module voltage in open mode. L add , C add and R add are inductance, capacitor and resistor of the auxiliary module, respectively. G cli,m (s) denotes the current reference to output transfer function of grid-connected inverter, Y oi,m (s) represents the equivalent output admittance of the system, i * gm (s) and i gm (s) are the reference current and output current of system, respectively, and their detailed form are expressed as [22].
When we adopt the parameters in Tables 3-5, the pole-zero maps of the current closed transfer functions for the traditional topology and the modified topology are shown in Figure 10, respectively. In Figure 10, p 1 and p 2 are the dominant closed-loop poles of the current transfer function for the traditional topology and the modified topology, respectively. Although p 2 is closer to the imaginary axis than p 1 , they are still very close to each other and far away from the imaginary axis. Therefore, compared with the traditional topology, the output stability of the modified topology is reduced, but all poles of the modified topology system are still in the left half plane and the whole system is still stable.
Energies 2021, 14, x FOR PEER REVIEW  14 of 19 traditional topology, the output stability of the modified topology is reduced, but all poles of the modified topology system are still in the left half plane and the whole system is still stable.

Simulation Results
With the detailed discussion of the modified topology, the MATLAB/Simulink was performed to achieve the verification. In the simulation, the fault type is that the voltage of phase B drops to 0.5 p.u. The parameters of other main circuits are shown in Table 2, and the parameters of the auxiliary modules are shown in Table 5. The results of the traditional topology and the modified topology are shown in Figures 11 and 12, respectively.
Comparing the results in Figures 11 and 12, when the modified topology is adopted, the unbalanced voltage at PCC1 can be corrected, and the inverter output current keeps being balanced. The oscillation value of the output active power is reduced from 0.49 to 0.17 p.u., and the output reactive power oscillation value is reduced from 0.46 to 0.15 p.u. The oscillation value of active power for the modified topology is 33.88% of that of the traditional topology and the reactive power oscillation value is reduced to 32.17% of the value of traditional topology. The simulation results show that the modified topology can correct the unbalanced voltage at the output of the inverter and reduce the oscillation of the output active power and reactive power.

Va
Amplitude value of A-phase voltage 50 V (1 p.u.)

P0
Output power 105 W (1 p.u.) traditional topology, the output stability of the modified topology is reduced, but all poles of the modified topology system are still in the left half plane and the whole system is still stable.

Simulation Results
With the detailed discussion of the modified topology, the MATLAB/Simulink was performed to achieve the verification. In the simulation, the fault type is that the voltage of phase B drops to 0.5 p.u. The parameters of other main circuits are shown in Table 2, and the parameters of the auxiliary modules are shown in Table 5. The results of the traditional topology and the modified topology are shown in Figures 11 and 12, respectively.
Comparing the results in Figures 11 and 12, when the modified topology is adopted, the unbalanced voltage at PCC1 can be corrected, and the inverter output current keeps being balanced. The oscillation value of the output active power is reduced from 0.49 to 0.17 p.u., and the output reactive power oscillation value is reduced from 0.46 to 0.15 p.u. The oscillation value of active power for the modified topology is 33.88% of that of the traditional topology and the reactive power oscillation value is reduced to 32.17% of the value of traditional topology. The simulation results show that the modified topology can correct the unbalanced voltage at the output of the inverter and reduce the oscillation of the output active power and reactive power.
Table3. Operating parameters of main circuit used in experiments.

Va
Amplitude value of A-phase voltage 50 V (1 p.u.)

Simulation Results
With the detailed discussion of the modified topology, the MATLAB/Simulink was performed to achieve the verification. In the simulation, the fault type is that the voltage of phase B drops to 0.5 p.u. The parameters of other main circuits are shown in Table 2, and the parameters of the auxiliary modules are shown in Table 5. The results of the traditional topology and the modified topology are shown in Figures 11 and 12, respectively.
Comparing the results in Figures 11 and 12, when the modified topology is adopted, the unbalanced voltage at PCC 1 can be corrected, and the inverter output current keeps being balanced. The oscillation value of the output active power is reduced from 0.49 to 0.17 p.u., and the output reactive power oscillation value is reduced from 0.46 to 0.15 p.u. The oscillation value of active power for the modified topology is 33.88% of that of the traditional topology and the reactive power oscillation value is reduced to 32.17% of the value of traditional topology. The simulation results show that the modified topology can correct the unbalanced voltage at the output of the inverter and reduce the oscillation of the output active power and reactive power. Output current (p.u.)

Experimental Results
In order to confirm the simulation results, the three-phase converter was verified by downscaling the levels of voltage and power. The overall configuration of the experimental setup is shown in Figure 13. The core control algorithm is implemented on TMS320F28335, while the intelligent power module (IPM) is PM150RLA120. IT6516C DC source is used to generate DC voltage and Chroma 61702 AC source is implemented to generate AC voltage to simulate grid voltage. The auxiliary module consists of three identical single-phase inverters, all of which adopt the filter composed of L add , R add and C add . L f is the filter inductance of grid-connected inverter output circuit. In the experiment, the fault type is that the voltage of phase B drops to 0.5 p.u. The parameters of other main circuits are shown in Table 3, and the parameters of auxiliary modules are shown in Table 4. The experimental results of the traditional topology and the modified topology are shown in Figures 14 and 15

Experimental Results
In order to confirm the simulation results, the three-phase converter was verified by downscaling the levels of voltage and power. The overall configuration of the experimental setup is shown in Figure 13. The core control algorithm is implemented on TMS320F28335, while the intelligent power module (IPM) is PM150RLA120. IT6516C DC source is used to generate DC voltage and Chroma 61702 AC source is implemented to generate AC voltage to simulate grid voltage. The auxiliary module consists of three identical single-phase inverters, all of which adopt the filter composed of Ladd, Radd and Cadd. Lf is the filter inductance of grid-connected inverter output circuit. In the experiment, the fault type is that the voltage of phase B drops to 0.5 p.u. The parameters of other main circuits are shown in Table 3, and the parameters of auxiliary modules are shown in Table  4. The experimental results of the traditional topology and the modified topology are shown in Figures 14 and 15, respectively.   Comparing the results of the traditional topology and the modified topology in Figures 14 and 15, the unbalanced voltage at PCC1 can be corrected under the modified topology, and the inverter output current keeps balanced. The oscillation value of the output active power is reduced from 43.35 to 13 W, and the output reactive power oscillation value is reduced from 55.06 to 15.08 var. The oscillation value of active power in the modified topology is 29.99% of that in traditional topology and the reactive power oscillation value is reduced to 27.39% of the value of the traditional topology. The experimental results show that the modified topology can correct the unbalanced voltage at the output of the inverter and reduce the oscillation of the output active power and reactive power.

Conclusions
The grid-connected inverter with modified topology could compensate the negativesequence and the zero-sequence components of the output voltage, so that the reference current equation of the inverter meets the solvability condition, thus eliminating the output power oscillation while the output current waveform still meets the requirements of grid codes. The simulation and experimental results show that the modified topology can effectively correct the unbalanced voltage and reduce the output active power oscillation and reactive power oscillation.
When the grid voltage is balanced, grid voltage does not contain negative-sequence components and zero-sequence components. Therefore, the output voltage reference value of the auxiliary module is zero at this time, and the auxiliary module will not output voltage, nor will it absorb power from the circuit or inject power to circuit. The auxiliary module is always connected to the circuit regardless of the unbalanced grid voltage fault or normal grid voltage, but when the grid voltage is balanced, the auxiliary module will not play a role.
The auxiliary voltage source can be a DC voltage source, a large capacitor, a super capacitor, or other energy storage units. This article aims to illustrate the function of the auxiliary module, so in the experiment, only the DC voltage source is used. In the future, the methods of using large capacitors or other energy storage structures to replace the Comparing the results of the traditional topology and the modified topology in Figures 14 and 15, the unbalanced voltage at PCC 1 can be corrected under the modified topology, and the inverter output current keeps balanced. The oscillation value of the output active power is reduced from 43.35 to 13 W, and the output reactive power oscillation value is reduced from 55.06 to 15.08 var. The oscillation value of active power in the modified topology is 29.99% of that in traditional topology and the reactive power oscillation value is reduced to 27.39% of the value of the traditional topology. The experimental results show that the modified topology can correct the unbalanced voltage at the output of the inverter and reduce the oscillation of the output active power and reactive power.

Conclusions
The grid-connected inverter with modified topology could compensate the negativesequence and the zero-sequence components of the output voltage, so that the reference current equation of the inverter meets the solvability condition, thus eliminating the output power oscillation while the output current waveform still meets the requirements of grid codes. The simulation and experimental results show that the modified topology can effectively correct the unbalanced voltage and reduce the output active power oscillation and reactive power oscillation.
When the grid voltage is balanced, grid voltage does not contain negative-sequence components and zero-sequence components. Therefore, the output voltage reference value of the auxiliary module is zero at this time, and the auxiliary module will not output voltage, nor will it absorb power from the circuit or inject power to circuit. The auxiliary module is always connected to the circuit regardless of the unbalanced grid voltage fault or normal grid voltage, but when the grid voltage is balanced, the auxiliary module will not play a role.