Review of Technical Design and Safety Requirements for Vehicle Chargers and Their Infrastructure According to National Swedish and Harmonized European Standards

: Battery electric vehicles demand a wide variety of charging networks, such as charging stations and wallboxes, to be set up in the future. The high charging power (typically in the range of a couple of kW up to a couple of hundred kW) and the possibly long duration of the charging process (up to more than 24h) put some special requirements on the electrical infrastructure of charging stations, sockets, and plugs. This paper gives an overview of the technical design requirements and considerations for vehicle charging stations, sockets, and plugs, including their infrastructure, according to the Swedish Standard 4364000, “Low-voltage electrical installations— Rules for design and erection of electrical installations”, and the corresponding harmonized European standards. In detail, the four internationally categorized charging modes are explained and the preferable charging plugs, including their two-bus communication, according to European Directives are shown. The dimensioning of the supply lines and the proper selection of the overcurrent protection device, the insulation monitor, and the residual current device are described. Furthermore, a comprehensive overview of the required safety measures, such as the application of an isolation transformer or the implementation of an overvoltage protection mechanism, and the limits for conducted electromagnetic emissions, such as low-frequency harmonics or high-frequency (150 kHz to 108 MHz) emissions, are given.


Introduction
The number of deployed electric vehicles has significantly increased throughout the past few years [1,2], and vehicles' battery capacities are becoming larger, as well [3]. In the future, this trend is presumably going to continue [3,4]. Thus, the energy demand and the power requirements on the electrical grid, due to the charging of electric vehicles, are steadily rising, as well. Especially, the high charging power (typically in the range of a couple of kW up to a couple of hundred kW) and the long charging duration of the charging process (up to more than 24 h) put some special requirements on charging stations' infrastructure, including charging plugs and charging sockets. Furthermore, to implement smart charging strategies, such as sharing of the available power among several vehicles [5], electricity-price triggered charging [6], primary and secondary frequency control [7,8] capability, or utilization as a domestic energy storage system (ESS) [9], a communication between the vehicle and the charging station/socket is required. The currently available national and international regulations, as well as directives, shall help to

Charging Modes
As described in [15], there are four different charging modes for BEVs and PHEVs, which are illustrated in Figure 1. In general, charging mode 1, 2 and 3 utilize an on-board charger (OBC), which is supplied by the AC mains or an AC charging station. Charging mode 4 instead employs a DC charging station, and it is often referred to as fast charging. Furthermore, charging mode 3 and charging mode 4 require a special and permanently installed electrical infrastructure, including a communication between the charging station and the vehicle. In contrast, charging mode 1 can be realized by a direct connection between a domestic power socket and the OBC without requiring any additional communication infrastructure between the mains and the vehicle. Similar to charging mode 1, charging mode 2 can utilize a domestic power socket, but some additional equipment is needed. During the charging process, independent of the charging mode, the required battery management system (BMS) shall ensure that each of the individual battery cells are evenly charged (typically, using passive balancing [16,17]) and that the maximum battery voltage limit is not exceeded. Moreover, the BMS can also request to reduce the reference current, which is controlled by the OBC or the DC charging station, to ensure not to exceed the maximum allowable battery temperature. In the following, the individual charging modes are explained in detail.  Figure 1. Illustration of the four charging modes as described in [12]. As already mentioned, charging mode 1 consists of a direct connection between the electric vehicle and the AC mains, 230 V/400 V with a maximum allowable current rating not exceeding 16 A. Typically, a common domestic (single-phase) AC socket, without any additional safety systems, can be used to supply the vehicle. The OBC rectifies the AC voltage to charge the battery. Unless unplugged, the lead is always live when using charging mode 1. Normally, charging mode 1 is only used for light vehicles, such as electric bikes or scooters with a low-voltage (≤60 V) battery system and a maximum charging power of a couple of hundred watts. In some European countries, charging mode 1 is subject to restrictions in public areas, and it is not allowed in Israel, the United Kingdom, and the United States [18]. According to [12], charging mode 1 is usually not supported for electric passenger cars.
Unlike charging mode 1, charging mode 2 requires some additional electrical control/safety equipment, referred to as electric vehicle supply equipment (EVSE). The EVSE is placed between the OBC and the AC power socket, typically integrated in the charging cable. Via a two-wire communication bus and a control unit, the EVSE can set the reference charging current for the OBC. Additionally, the EVSE monitors the charging process. When the battery is fully charged, the EVSE disconnects the OBC from the AC mains, referred to as safety lock-out. Furthermore, the EVSE can detect hardware faults, such as a faulty cable plug connection or an external short-circuit fault. For charging mode 2, both domestic (single-phase) and industrial (three-phase) AC sockets with a current rating up to 32 A can be used. Consequently, the maximum three-phase charging power, assuming unity power factor (cos (ϕ) ≈ 1) [19], according to becomes Nonetheless, only AC sockets designated for charging should be used, since the charging process can occupy the available power capability of the grid's connection point for several hours, as listed in Table 1. Furthermore, domestic (single-phase) AC sockets can rapidly wear out when loaded over a long period with rated current [20]. Thus, charging a vehicle from a domestic AC socket, which is not designated for charging, should be considered only as "emergency charging". Charging mode 3 requires that the BEV or PHEV is charged via an AC charging station, which is permanently connected to the grid. The EVSE, including the control and safety functions, is directly integrated into the charging station. Normally, wallboxes, charging columns, commercial charging points and all automatic AC charging systems (with an integrated EVSE) are considered as AC charging stations in accordance with charging mode 3. The current rating of the charging station can be up to 63 A [12]. Consequently, the maximum three-phase charging power, assuming unity power factor (cos (ϕ) ≈ 1) [19] , according to becomes Since the charging power for charging mode 3 can be significantly increased in comparison to charging mode 1 and charging mode 2, specially designated AC sockets and charging plugs should be used, as further explained in Section 3. Charging mode 3 should be preferably used for home charging stations and, according to the EU directive 2014/94 [21], it should be employed at public charging stations.
Charging mode 4 is the only mode that utilizes DC current. As illustrated in Figure 1d, no OBC is required, since there is a direct connection between the charging station and the vehicle's battery. The power electronics circuitry, which is integrated in the DC charging station, can adjust the output voltage to control the DC charging current. Typically, the output voltage can be adjusted up to 1000 V and the charging current can be up to 400 A. Thus, a charging station according to charging mode 4 can theoretically achieve a charging power of a couple of hundred kW [22]. However, the battery's charging efficiency is significantly decreased when using such a high charging power [23]; thus, the BMS has to constrain the maximum charging power to comply with the temperature limit of the battery system. Therefore, DC charging stations for passenger vehicles are often operated with a continuous power from 40 kW to 130 kW.

Charging Plugs and Socket-Outlets
The high charging power, the possibly long duration of the charging process (see Table 1) put some special requirements on the electrical infrastructure, including the charging plugs and the charging sockets. Furthermore, with respect to the project IEEE 2030 [24], "Guide for Smart Grid Interoperability of Energy Technology and Information Technology Operation with the Electric Power System (EPS), End-Use Applications, and Loads", the charging plugs and sockets should preferably comprise a communication interface and the charging infrastructure should allow for bidirectional power flow capability.
For example, domestic (single-phase) wall-mounted AC sockets or plugs according to the SS-428-08-34 [25] or the internationally harmonized IEC standard SS-IEC-60884-1 [26] can rapidly wear out when loaded over a long time with rated current [20]. In contrast, industrial (three-phase) socket-outlets according to the SS-EN-60309-1 [27] and the SS-EN-60309-2 [28] can be fully utilized, but the current rating shall not exceed 32 A according to charging mode 2 [12]. Nonetheless, the charging process can easily occupy the full current capability of the grid's connection point for a long duration (see Table 1), while no other loads can be used. Thus, it is often reasonable to adjust/reduce the charging current accordingly or to balance the available power among all loads. However, both domestic and industrial AC sockets do not provide any communication between the vehicle's OBC and the AC socket to adjust the reference current for the charging process. Therefore, to adjust/reduce the charging current, at least some additional EVSE would be required when charging a vehicle from a domestic or industrial socket-outlet (charging mode 2). For example, Figure 2 shows a single-phase charging cable from Deltaco [29] with a SchuKo and a Type 2 connector including an in-line integrated EVSE, which includes a communication interface to adjust the charging current's reference between 10 A and 16 A. To achieve higher charging power levels (>>20 kW), as desired for public charging stations, the charging plugs and sockets according to the standard series SS-EN-62196 [30][31][32] (harmonized European standard) shall be used, which is in accordance with the international standard series IEC-62196, "Plugs, socket-outlets, vehicle connectors and vehicle inlets-Conductive charging of electric vehicles". The plugs and socket-outlets according to the standard series SS-EN 62196 are not only rated for high current levels, these also comprise an interface for a two-wire bus communication, referred to as vehicle to grid (V2G) communication interface in accordance with the SS-EN-ISO 15118-1 [33]. With the help of the communication interface, smart charging strategies can be easily realized. For example, the available power of a public charging station could be evenly distributed among all vehicles [5] or a vehicle is only charged if the electricity price is below a certain threshold [6]. Moreover, considering the IEEE Std 1547 [34], "IEEE Standard for Interconnection and Interoperability of Distributed Energy Resources with Associated Electric Power Systems Interfaces", vehicles' charging infrastructure can provide also ancillary service functions for distribution or transmission system operators, such as intentional local islanding possibility [9,35] or primary and secondary frequency control capability [7,8]. The Type 2 charging plug according to the standard SS-EN-62196-2 [31] can be seen in Figure 3a. It should be used for three-phase AC charging according to charging mode 3, but it is not limited to it. The Combo 2 charging plug according to standard SS-EN-62196-3 [32] can be seen in Figure 3b. It should be used for DC charging according to charging mode 4. With respect to the harmonized European standard series EN 62196, the EU directive 2014/94 [21] states that any public charging station should comprise at least one charging plug of Type 2 and one of type Combo 2. The combined charging socket of Type 2 and Combo 2 (CCS 2), manufactured by Khons Technology, can be seen in Figure 3c. This combined charging system (CCS) is commonly abbreviated as CCS 2 and it should be preferably used for EVs in Sweden and the European Union. As can be seen from Figure 3c, the CCS 2 socket comprises a two wire communication bus (PP and CP), a normal three-phase connection interface (L1, L2, L3, N, and PE), and a DC connection interface (DC+ and DC-). Both, the Type 2 and the Combo 2, as well as the CCS 2, charging plugs and sockets are recognized in North America under the recommended practice of the SAE J3068 [36], "Electric Vehicle Power Transfer System Using a Three-Phase Capable Coupler". Another (globally) popular charging system is the CHAdeMO system [39,40] (for DC charging), which stands for "CHArge de MOve". However, especially due the EU directive 2014/94 [21], the CCS 2 is becoming dominant in Europe in comparison to the CHAdeMO system. Furthermore, while using charging mode 3 or charging mode 4, an electrical or mechanical mechanism, sometimes referred to as latch-locking, should be used to lock the charging plug [12]. This measure should ensure a low electrical contact resistance.

Overcurrent Protection and Cable Dimensioning
The approximated time durations to fully charge a BEV with a nominal battery capacity of about 60 kWh with respect to different charging types are given in Table 1. For example, when using single-phase charging with a maximum current rating of about 10 A or 16 A, the required charging time can be up to 26.1 h or 16.2 h, respectively. Thus, when loading the electrical mains for such a long time with the rated current, it is important to properly dimension the electrical infrastructure, such as plugs and socket-outlets, including the cables and the overcurrent protection. Therefore, this section gives a short description on how to dimension the cables' conductor size and how to select the corresponding overcurrent protection device for a charging application.
In general, according to [12], any power-socket designated for charging should be placed as close as possible to the vehicle's parking spot. Thereby, the voltage drop (losses) along the cable should be kept as small as possible and the proper functioning of any overcurrent protection device should be ensured.

Selection of Overcurrent Protection Device
When designing the electrical installation for a charging station/socket, it is reasonable to start with the selection of the overcurrent protection device. As described in [12], any over-current protection device should satisfy the following relation with I B being the rated current of the load circuitry and I n being the nominal current of the selected circuit breaker or fuse. The conductors' nominal current capability I z can be described according to with I z,0 being the conductors' current capability for a certain cross-sectional area under consideration of the method of installation. The coefficients k T (temperature) and k M (grouping) should be used to correct the conductors' current rating relative to the ambient temperature and the number of touching multi-core cables or groups of single-core cables, respectively. Moreover, as further described in [12], the overcurrent protection device should also satisfy the relation with I 2 being the current value that ensures a proper functioning of the overcurrent protection device. For example, a typical tripping characteristic of a type C miniature circuit breaker, according to the SS-EN 60898-1 [41], with a nominal current rating of I n can be seen in  Typically, a miniature circuit breaker comprises two tripping mechanisms. A thermal and an electromagnetic mechanism are used for the protection against overcurrents or short-circuit faults, respectively. At the left-hand side of the thermal release zone in Figure 4 no overcurrent fault would be detected as long as the relative overcurrent I/I n is less than 1.13. Nonetheless, if the relative overcurrent I/I n exceeds 1.45, an overcurrent fault is certainly detected by the thermal tripping mechanism; thus, the condition in (7) would always be satisfied as long the current capability I z was chosen in accordance with (5). In comparison to the thermal release zone, the electromagnetic release zone describes the protection against short-circuit faults. As can be seen, a short circuit fault can be detected, if the relative overcurrent I/I n is higher than 5 and lower than 10 (EM release zone of type C circuit breaker). Moreover, for high short circuit currents (I/I n ≥ 10), the time till tripping is almost instantaneously. The boundaries of the EM release zone are dependent on the circuit breaker's characteristic (e.g., A, B, C, etc.) and should be chosen in accordance with the load. For instance, the high starting current of a electric line-start machine [42] shall not be misinterpreted as a short-circuit fault; thus, the lower boundary of the EM release should be accordingly chosen (typically, type C). For a charging application, the inrush currents can be easily limited by pre-charging resistors or soft starters. Thus, for charging applications, it is often sufficient to select a type B circuit breaker (EM release zone: 3 ≤ I/I n ≤ 5).

Placement of Overcurrent Protection Device
Normally, parallel loads can be operated at the same power socket as long as these are only consuming electrical energy. However, if power-consuming and power-generating devices are connected in parallel at the same connection point, the proper functioning of its closest over-current protection device might not be ensured anymore. Despite vehicle charging stations/sockets are mainly considered as power-consumers, these can also be utilized as energy-storages. In this way, a fleet of electric vehicles can possibly inject active power into the power-system to assist the primary or secondary frequency control functionality [7,8], and, thereby, the power-system's frequency can be maintained. Furthermore, a vehicle's battery could also be used as a domestic energy storage [9]. Therefore, as described in [12], the grouping factor k M in (5) shall be equal to one for any supply line feeding an individual charging point. This means that each designated charging point/socket must be individually protected against overcurrent and short circuit faults. In contrast, the grouping factor k M for the main line, supplying the distribution network of a charging station, can be reduced if a proper load control management system is used [12].

Permissible Voltage Drop along the Supply Line
According to [12], the maximum permissible voltage drop along the power supply line, from the mains distribution to the load, corresponds to 5%. As described in [12], the relative voltage drop V Drop,% [%] along the supply line can be calculated according to with V Drop being the absolute voltage drop at rated load operation, and V Phase,rat being the nominal phase voltage of the mains, corresponding to 230 V in Sweden [43]. Further, the absolute voltage at rated load, as described in [12], can be calculated according to as further explained in the following. As before mentioned, the rated load operation of the supply line should be considered when conducting the line's rated load current with the corresponding power factor angle ϕ [rad s −1 ]. For vehicle charging applications, it can be assumed that modern power electronic converters can achieve a power factor close to unity [44,45]. The dimensionless coefficient b corresponds to 2 or 1 for a single or three-phase system, respectively. The variables L [m] and A [mm 2 ] describe the conductors' length and their cross-sectional area, respectively. The relative resistivity ρ T [Ω mm 2 m −1 ] of the supply line's conductors is dependent on the operating temperature T [°C] and its material, such as copper or aluminum, which can be described as For example, the relative resistivity of copper corresponds to ρ 0 = 0.0168 Ω mm 2 m −1 at T 0 = 20°C with its correction factor α = 0.004 04 K −1 . If the relative reactance λ[Ω m −1 ] is not known, it can be assumed to be about 0.08 mΩ m −1 according to [12]. For example, Table 2 lists the maximum permissible cable lengths relative to the conductors' crosssectional area and the current rating (singe-phase or three-phase) under consideration of a maximum voltage drop V Drop,% of 5%. a An operating temperature of T = 55°C is assumed. b A power factor of cos(ϕ) ≈ 1 is assumed.

Protection against Electric Shock
This section gives a brief overview about the required safety measures according to [12] against an electric shock due to an indirect contact.

Residual Current Device
In a common TN (terre-neutre) earthing-system, the electrical infrastructure to supply any kind of charging system/station should be realized as a TN-S earthing-system [12]. To reduce the risk of any harm for the user of the charging station in case of an electrical insulation fault (protection against indirect contact), a residual current device (RCD) with a maximum residual current rating of 30 mA should be implemented according to [12]. In general, there are different types of RCDs, type AC, type A, type F, type B (type B+). So, the question arises, which RCD type to choose for the electrical infrastructure of a charging station/socket?
To answer this question, the different RCD detection features must be understood first. The illustrated pictograms in Figure 5 can be usually found on different RCD types, representing different features, which can be summarized as follows: The simplest of all RCD types is type AC, which can be used to detect only residual sinusoidal AC currents (Figure 5a). This type can only be used for electrical loads, and it is rarely used anymore, since it is not suitable for any kind of electronic loads, such as diode rectifiers and active rectifiers. Thus, type AC cannot be used for any kind of charging stations. In comparison to type AC, a type A RCD can additionally handle residual pulsating DC currents (Figure 5b), and it is the most used RCD type, commonly used for domestic installations. However, the proper function of a type A RCD is ensured as long the pure DC component of the fault current does not exceed 6 mA, because the magnetic core of the RCD could saturate otherwise. Similar to type AC, a type F RCD can detect residual sinusoidal and pulsating DC currents, but in addition it can cope with residual currents that are composed of multiple frequencies up to 1 kHz (Figure 5d Consequently, it can be concluded that a type A or a type F RCD can theoretically be used for charging stations, but it must be ensured that the DC component of the residual current does not exceed the saturation threshold current of the corresponding RCD type (6 mA for type A and 10 mA for type F). Since the RCD type B/B+ is the only one that can also cope with smooth residual DC currents, it should be preferably used for any kind of charging station. As already mentioned, a type AC RCD cannot be used, since it can only detect sinusoidal residual AC currents.

Insulation Monitor
In an IT (isolé-terre) network, the electrical distribution system shall have no connection to earth at all, or it shall have only a high-impedance connection. Usually, an RCD in an IT network does not trip after the first earth-fault. Thus, in addition to an RCD, an insulation monitor is required for an IT network. According to the recommendations in [12], the insulation monitor shall have the following characteristics for a charging station/socket:

•
Warning: If the insulation resistance has dropped below 300 Ω V −1 , an optical and/or acoustical warning signal shall be activated. An ongoing charging process can be completed, but no new charging process shall be started. • Alarm: If the insulation resistance has dropped below 100 Ω V −1 , an optical and/or acoustical warning signal shall be activated and within 10 s any ongoing charging process shall be stopped.
Furthermore, an insulation fault locator in compliance with the SS-EN 61557-9 [46] shall be used to identify the faulty electric circuit as fast as possible.

Further Safety Requirements
As described in [12], the electrical and electronic circuitry of a charging station/socket shall be protected by the housing/enclosure against climate conditions and intrusion of objects, which can be summarized as follows: • Protection against intrusion, dust, accidental contact and water: The enclosure of an outside located charging station/socket shall fulfill at least the requirements of IP code 43 according to the SS-EN 60529 [47]. IP code 43 means that the housing protects the electrical and electronic circuitry against intrusion of objects with a larger diameter of 1 mm and spraying water. • Protection against external mechanical impacts: The enclosure of a charging station/socket shall protect the electrical and electronic circuitry against external mechanical impacts. Therefore, the enclosure shall fulfill at least the requirements of IK code 07 according to the SS-EN 62262 [48]. IK code 07 means that the housing protects the electrical and electronic circuitry against external mechanical impacts with an impact energy of up to 2 Nm.
Furthermore, according to [12], any kind of charging station/socket or system shall fulfill the following electrical safety precautions: • Galvanic isolation: To avoid unwanted common mode currents, a galvanic isolation between the mains and the vehicle is required. Therefore, the vehicle's battery shall be supplied via a permanently installed transformer in accordance with the SS-EN 61558-2-4 [49]. • Protection against lightning strikes and transient overvoltages: To protect the electrical and electronic circuitry from any kind of unwanted overvoltages, a surge protection device type 2 according to the SS-EN 61643-11 [50] shall be implemented. • Emergency stop: When an emergency stop is required, the entire load current shall be interrupted and all live conductors, including the neutral conductor, shall be disconnected via an emergency stop button.

Limits for Current Harmonics and Conducted Electromagnetic Emissions
To generate the desired output voltage waveforms, the power electronic converters of charging stations or OBCs typically utilize various pulse width modulation (PWM) techniques. However, a PWM waveform contains an infinite series of voltage harmonics, which can cause current harmonics or electromagnetic interference (EMI) problems.
This section gives a brief overview about the recommended limits for current harmonics and conducted electromagnetic emissions (EME), applicable for charging stations and OBCs.

Harmonic Current Emissions
In general, there are no strict regulations about the limits for harmonic current emissions (current harmonics or current THD) of grid-tied power electronic devices, such as on-board chargers or charging stations. Nonetheless, as described in [51,52], harmonic currents can cause a local fluctuation and distortion of the power system's voltage level. For example, increased voltage levels (>230 V) could lead to damages of electrical loads and equipment, whereas lower voltage levels (<230 V) typically lead to increased ohmic losses (when considering constant power loads). Furthermore, harmonic currents can cause flicker of lighting. Hence, as described in the SS-EN-50160 [43], "Voltage characteristics of electricity supplied by public distribution systems", the power system's supply voltage should be maintained at about 230 V (50 Hz), and only small voltage deviations can be tolerated. Therefore, any kind of harmonic currents shall be kept as small as possible. The IEEE Standard 519 [53], "Standard for Harmonic Control in Electric Power Systems", gives recommendations about the permissible magnitude of harmonic current components (up to the 50th component) and the total demand distortion (TDD) relative to the maximum demand current I L and the short circuit capacity I SC . For example, Table 3 shows the current distortion limits for systems rated 120 V through 69 kV, relevant for charging stations and OBCs.
To understand the ratio of the short circuit capacity I SC and the maximum load demand current I L better, Figure 6 gives a schematic illustration about the charging of a vehicle via an OBC. At the point of common coupling (PCC), an OBC is connected to the power system, charging the vehicle's battery with a maximum (demand) load current I L . At the PCC, the grid can be characterized by the loop impedance Z Grid , which is often referred to as Thévenin impedance. The size of the loop impedance Z Grid characterizes the PCC's current harmonic susceptibility. For example, a strong grid has a low loop impedance; thus, the current harmonics have a reduced impact on the PCC's voltage deviation/distortion.  In practice, the loop impedance is often expressed in terms of the short circuit capacity I SC , which corresponds to the theoretical current at the PCC in case of a short circuit fault, which can be estimated according to As given in [53], the value of the TDD is defined as "The ratio of the root mean square of the harmonic content, considering harmonic components up to the 50th order and specifically excluding interharmonics, expressed as a percent of the maximum demand current", which can be mathematically written as follows In contrast, according to [53], the value of the the THD is defined as "The ratio of the root mean square of the harmonic content, considering harmonic components up to the 50th order and specifically excluding interharmonics, expressed as a percent of the fundamental current", which should not be misinterpreted as the TDD. It should be noted that the THD is always lower than the (THD < TDD), except at the maximum demanded load current (THD = TDD).
As can be seen in Table 3, depending on the ratio I SC /I L , the maximum allowable TDD can vary between 5% and 20%. This is also valid for any kind of vehicle charging application. However, as described in footnote c of Table 3, the TDD must be limited to 5%, and the harmonic magnitudes must be limited to the values given in the first row (I SC /I L < 20), if the charging station or OBC is also intended to be used for bidirectional power flow.

Conducted Electromagnetic Emissions
To ensure the proper functioning of the charging infrastructure and the vehicles' onboard devices, unwanted EMI problems should be avoided. Therefore, potential sources of EMEs should be identified and mitigated during an early stage of the system's design process before the application of filters, shielding, and the like.
The Comité International Spécial des Perturbations Radioélectriques (CISPR; English: International Special Committee on Radio Interference) has issued several standards about measurement procedures of EME and the classification of various kind of electrical products relative to their EME levels. During the design process of a charging station or an OBC, it is often reasonable to focus on the conducted emissions on power cables [54,55], since these are related to the radiated emissions [56]. Depending on the charging modes described in Section 2, different CISPR standards are applicable [57]. For example, according to the CISPR 14-1 [58],"Electromagnetic compatibility-Requirements for household appliances, electric tools and similar apparatus-Part 1: Emission", the conducted emissions on the AC supply lines of the OBC should be considered when using charging mode 1 to charging mode 3. In contrast, for DC charging stations (charging mode 4), CISPR 25 [59], "Vehicles, boats and internal combustion engines-Radio disturbance characteristics-Limits and methods of measurement for the protection of on-board receivers", applies; thus, the conducted emissions on the battery's DC link rails should be limited. Both, the CISPR 14-1 and the CISPR 25, are applied in Sweden under its translated versions SS-EN 55014-1 [60] and SS-EN 55025 [61], respectively.
Since the power rating of a DC charging station is typically larger than the power rating of an OBC, charging mode 4 represents the greatest challenge regarding the limitations of EME levels [62]. To measure the conducted emissions on the DC link rails according to the SS-EN 55025 [61], two line impedance stabilization networks (LISNs) are required. A LISN mainly consist of an LC-filter, which shall couple the high-frequency noise (DM and CM components) into the measurement equipment (typically a spectrum analyzer). The low-frequency components shall not be affected by the LISNs. As depicted in Figure 7, the two LISNs must be inserted into the positive and the negative DC link rail between the battery and the power electronics converter of the charging station. According to the SS-EN 55025 [61], the test-bench used for the measurements shall be in compliance with the CISPR series 16 [63],"Specification for radio disturbance and immunity measuring apparatus and methods". For example, as shown in [64], the surface of the test-bench shall be covered by a copper sheet (ground plate), spacers shall be used to have a separation of 5 cm to the ground plate and, further, a certain distance must be kept between the LISNs and the power electronics circuitry. The measurement of conducted emissions according to the SS-EN 55025 [61] is a typical pre-compliance test used for individual components, such as the power electronics converter of a charging station. The conducted emission levels are typically quantified in dBµV within the frequency range from 150 kHz to 108 MHz. The limits for broadband conducted disturbances on power input terminals according to the SS-EN 55025 [61] are given in Table 4.

Conclusions
This paper has given a comprehensive but concise overview about the technical design and safety requirements of conductive charging stations and systems, including their infrastructure, for BEVs and PHEVs according to the governing Swedish and the corresponding harmonized international and European standards. Conclusively, the main topics of the paper and the most important regulations can be shortly summarized as follows.
The four internationally categorized charging modes and the most common charging plugs and sockets have been described. To implement smart charging strategies, it is necessary that the charging infrastructure comprises a communication bus between the vehicle and the charging station. According to current European directives, any public charging station shall provide at least the charging possibility via a Type 2 and a Combo 2 plug, utilizing charging mode 3 and charging mode 4, respectively. Charging via other plugs, such as the CHAdeMO charging plug, can be publicly offered, as well, although it is not required.
Furthermore, the required overcurrent protection for charging sockets under consideration of the maximum permissible voltage drop of 5% has been described. Vehicles shall only be charged at designated charging sockets, which shall be placed as close as possible to the vehicle. Each charging socket must be individually fused, which guarantees the proper function of the fuse even when feeding energy back to the mains.
With respect to the user's safety, different required features have been described. Each charging point shall be protected by an RCD. Preferably, an RCD of type B or B+ shall be used, whereas type AC shall not be used at all. Additionally, to achieve galvanic isolation, the vehicle shall be supplied over a permanently installed transformer.
Last but not least, the maximum permissible content of harmonic and electromagnetic emissions have been described. Depending on the short circuit capacity of the charging station or socket, the maximum permissible current TDD can be up to 20%. Nonetheless, when feeding energy back from the vehicle's battery to the mains, the maximum permissible current TDD shall not exceed 5%. This aspect is quite important when designing and sizing the power electronics circuitry, including its passive components, for a charging station or an OBC. Funding: The authors would like to thank the Swedish Energy Agency (Energimyndigheten) for the provided financial support.

Conflicts of Interest:
The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript, or in the decision to publish the results.