Thermo-Hydraulic Performance Characteristics and Optimization of Protrusion Rib Roughness in Solar Air Heater

: To enhance the thermal performance of solar air heaters (SAHs), protrusion ribs on the absorber are considered to be an attractive solution due to their several advantages. These ribs do not cause a signiﬁcant pressure drop in the SAH duct and help to enhance the heat transfer to ﬂowing air. On the other hand, a degree of roughness of the protrusion rib on the absorber can be produced by pressing the indenting device without adding additional mass. In this paper, the thermo-hydraulic performances of different roughnesses of the conical protrusion rib on the absorber plate have been evaluated by the mutual consideration of thermal as well as hydraulic performance in term of net effective efﬁciency. Therefore, an analytical technique has been exploited to predict the characteristics of the net effective efﬁciency under various operating conditions, such as the ﬂow Reynolds number, temperature increase parameter and insolation. The effects of the conical protrusion rib roughness—namely the relative rib pitch (p/e) and relative rib height e/D) in the ranges of 6–12 and 0.200–0.044, respectively—have been evaluated. The highest value of net effective efﬁciency of 70.92% was achieved at a p/e of 10 and e/D of 0.0289. The optimization of the rib parameters has been carried out in different ranges of temperature increase parameters for the highest values of net effective efﬁciency. A unique combination of rib parameters—a p/e of 10 and e/D of 0.044—are observed to lead to the best performance when operating a solar air heater with a temperature increase parameter of more than 0.00789 K · m 2 /W.


Introduction
Energy demand is growing rapidly due to industrialization and urbanization, with social and cultural development leading to a large amount of energy consumption per capita. Mostly, energy is produced from conventional energy sources such as crude oil, natural gas, coal and nuclear power, and the contributions of these fuel sources globally are large, at 34%, 24%, 27% and 10%, respectively [1]. These sources are reserved in the Earth and will be exhausted in a few years. Therefore, researchers are exploring alternatives to these fuels to replace them. Solar energy is most appropriate source of energy and has a great deal of potential as it is omnipresent and provides a pollution-free environment during operation [2]. Solar energy may be exploited in different forms depending on the application, such as electricity generation, water distillation, heating/cooling and cooking, etc. [3]. Solar air heaters (SAHs) are known as the most suitable solar thermal system to exploit solar energy in the easiest and most convenient way. The absorber is the principal component of an SAH, which exploits solar energy and converts it into thermal energy in the form of air. However, it has been observed that the heat transfer capabilities of smooth absorbers are low due to the low convective heat transfer coefficient, which is meet the following objectives: firstly, to evaluate the net effective efficiency of conical protrusion rib roughnesses using correlations of the friction factor and Nusselt number at various kinds of insolation, as published in a previous study [28]; secondly, to optimize the conical protrusion rib roughness to obtain the best effective efficiency in different ranges of temperature increase parameters.

Conical Protrusion-Roughened SAH
An SAH is a well-known solar thermal system which is utilized to heat the air by absorbing the available insolation. The performance of an SAH depends on the intensity of insolation, the concentration ratio of the collector, the heat transfer capability of the absorber plate to air, the absorptivity and emissivity of the absorber plate and measures taken to keep the heat losses at a minimum, especially from the top glass cover. An SAH consists of a flat absorber plate parallel to the air flow passage where air is to be heated. In order to eliminate the heat loss from the absorber, a glass cover is employed to minimize the top heat losses, and insulation is employed to eliminate the back and side heat losses. The absorber absorbs solar insolation when it is struck through the glass cover and heats the flowing air in the passage, as shown in Figure 1. When aiming to design the optimum collector, temperature variation, convective heat transfer coefficient and friction factor for an absorber, the heat removal factor and useful heat gain play a dominant role in understanding the heat extraction rate from the absorber to air. Previously, a surface with conical protrusion rib roughness (Figure 2a) has been analyzed to predict the heat transfer coefficient, friction factor and thermal efficiency. Higher heat transfer due to the sharp apex corner of the conical protrusion ribs has been attributed to high turbulence with a strong re-attachment point in the vicinity of the rib, which helps to disturb the sub-laminar layer, as presented in Figure 2b [28]. When aiming to design the optimum collector, temperature variation, convective heat transfer coefficient and friction factor for an absorber, the heat removal factor and useful heat gain play a dominant role in understanding the heat extraction rate from the absorber to air. Previously, a surface with conical protrusion rib roughness (Figure 2a) has been analyzed to predict the heat transfer coefficient, friction factor and thermal efficiency. Higher heat transfer due to the sharp apex corner of the conical protrusion ribs has been attributed to high turbulence with a strong re-attachment point in the vicinity of the rib, which helps to disturb the sub-laminar layer, as presented in Figure 2b [28].
The energy conservation for various principal components of an SAH-i.e., the glass cover, absorber plate and air-have been discussed and attributed to the evaluation of the net effective efficiency. The following assumptions have been made during the analysis; (i) the thermo-physical properties of the glass cover, absorber plate and air remain equal; (ii) there is no effect of climatic parameters such as humidity and climatic variation; and (iii) there is no effect caused by the sun's location and the location of interest (latitude and longitude). A simplified thermal network of an SAH (presented in Figure 1) is shown in Figure 3, in which the thermal resistance is evaluated on the basis of convective and radiative heat transfer coefficients between the absorber plate and air, the absorber plate and the glass cover and the glass cover and the sky. The absorber plate absorbs solar insolation and distributes this into useful heat gain to the air; however, top heat loss, bottom heat loss and side-edge heat loss are also present.  The energy conservation for various principal components of an SAH-i.e., the glass cover, absorber plate and air-have been discussed and attributed to the evaluation of the net effective efficiency. The following assumptions have been made during the analysis; (i) the thermo-physical properties of the glass cover, absorber plate and air remain equal; (ii) there is no effect of climatic parameters such as humidity and climatic variation; and (iii) there is no effect caused by the sun's location and the location of interest (latitude and longitude). A simplified thermal network of an SAH (presented in Figure 1) is shown in Figure 3, in which the thermal resistance is evaluated on the basis of convective and radiative heat transfer coefficients between the absorber plate and air, the absorber plate and the glass cover and the glass cover and the sky. The absorber plate absorbs solar insolation and distributes this into useful heat gain to the air; however, top heat loss, bottom heat loss and side-edge heat loss are also present. Heat exchange between the absorber and glass cover:  Heat exchange between the absorber and glass cover: The convective heat transfer between the absorber and cover is calculated as given below: where ν · α The radiation resistance from the top cover is calculated to account for the radiation exchange with the sky at temperature, T s , the radiation heat transfer coefficient is given below: The resistance to the surroundings and the top loss coefficient from the collector to ambient air is calculated as The edge loss coefficient and back heat loss coefficient are calculated as The useful heat gain to fluid is as follows: where the overall heat loss coefficient is where (τα) is the transmittance-absorptance product of the absorber. The thermal efficiency of the collector is Furthermore, the thermo-hydraulic efficiency in terms of the net effective efficiency [30] is calculated as given below: The net effective efficiency of the collector is where C (=0.18) is the conversion factor of the thermal energy converted from mechanical power. P m is the mechanical power needed to drive the fan/blower to cause the air to flow at a predetermined level, given as The pressure drop (∆P) d can be evaluated by determine the friction factor value, which is given below:

Steps to Calculate the Thermo-Hydraulic Performance
Characteristics of the thermo-hydraulic performance (net effective efficiency) of the conical protrusion rib roughened surface of an SAH have been evaluated under similar operating conditions to those available in the literature [25]. The rib parameters were selected from the authors' previous study [28]. All systems, ribs and operating parameters are listed in Table 1. In order to evaluate the net effective efficiency of the conical protrusion rib roughened surface in an SAH, it was compared with a smooth-duct SAH. However, the convective heat transfer coefficient and friction factor of the conical protrusion rib roughened surface were exploited and evaluated with regard to their respective correlations. The rib parameters of the conical protrusion rib roughened surface were exploited to predict the thermo-hydraulic performance. The steps taken in the procedures are given below: 1.
The rib parameters-i.e., the relative rib pitch and relative rib height-were identified in the entire study for which the characteristic of the net effective efficiency needed to be evaluated. System parameters of the SAH and operating parameters such as the solar insolation, inlet air temperature, ambient temperature, sky temperature, mass flow rate and wind speed needed to be kept fixed; 2.
The outlet temperature of air was determined using insolation and temperature increase parameters, while the inlet air temperature was considered as ambient temperature: Then, the thermo-physical properties of air were considered as a function of temperature and evaluated based on the mean temperature of air;

3.
The overall heat loss coefficient was the sum of the back cover heat loss coefficient, side-edge heat loss coefficient and top heat loss coefficient, which were evaluated in the following manner: The top heat loss coefficient was determined by the proposed correlation of Akhtar and Mullick [31]: The mean plate temperature was approximated as 10 • C above the mean air temperature. The back cover heat loss coefficient and side edge heat loss coefficient were evaluated in the following manner: and Useful heat gain was estimated by determining the overall heat loss coefficient. Then, the Reynolds number of air was evaluated in the following manner: 5.
The Nusselt number was estimated by the correlation of the conical protrusion rib roughness in the air passage [28]; then, the convective heat transfer of the absorber plate was estimated as follows: 6. Again, the heat gain by air was determined by estimating the heat removal factor and collector fin efficiency as follows [32]: where Q u1 and Q u2 were compared; if these values deviated from each other, the new value of T pm was determined using the value of heat gain, Q u2 , from Equation (17). Iterations continued until the values of Q u1 and Q u2 became nearly equal i.e., < 1% : 8.
The friction factor was estimated by the correlation of the conical protrusion rib roughness [28]. Then, the pressure drop and mechanical power needed to propel the air through SAH were calculated: Finally, the net effective efficiency was estimated for the conical protrusion rib roughened SAH by Equation (9). The process was performed for different sets of rib and operating parameters. The flow chart of this methodology is presented in Figure 4.

Result and Discussion
The net effective efficiency of the conical protrusion rib roughened surface of an SAH was evaluated according to methodology discussed in the previous section. The

Result and Discussion
The net effective efficiency of the conical protrusion rib roughened surface of an SAH was evaluated according to methodology discussed in the previous section. The distribution of the net effective efficiency showed that an indirect comparison of useful heat gain to air and the pumping power of air could be made for various conical protrusion rib parameters as a function of the Reynolds number and temperature increase parameter. Prior to starting the discussion on net effective efficiency, the behavior of the useful heat gain, absorber temperature and pumping power need to be understood; therefore, the respective plots of useful heat gain, pumping power requirements and mean collector temperature are presented as a function of the Reynolds number for an e/D of 0.0289, p/e of 10 and I of 1000 W/m 2 , as shown in Figure 5.
Energies 2021, 14, x FOR PEER REVIEW 11 distribution of the net effective efficiency showed that an indirect comparison of u heat gain to air and the pumping power of air could be made for various co protrusion rib parameters as a function of the Reynolds number and temperature inc parameter. Prior to starting the discussion on net effective efficiency, the behavior o useful heat gain, absorber temperature and pumping power need to be unders therefore, the respective plots of useful heat gain, pumping power requirements and collector temperature are presented as a function of the Reynolds number for an e 0.0289, p/e of 10 and I of 1000 W/m 2 , as shown in Figure 5. It can be seen from the plots that the mean temperature of the absorber decreased with the Reynolds number and became nearly constant. Contrary to thi heat gain increased with the Reynolds number and became nearly flat for a high Rey number, implying that a lower plate temperature exhibited low heat loss through the cover and resulted in a high heat extraction rate by air from the absorber. On the hand, the pumping power increased slightly with the Reynolds number, bu increment rate was not significant.

Effect of Relative Height
The net effective efficiency of the conical protrusion rib roughened absorber SAH was evaluated for all possible combinations of relative rib heights and re pitches with 600 W/m 2 , 800 W/m 2 and 1000 W/m 2 of insolation. The net effective effic of a smooth SAH was also evaluated for comparison purposes. In Figure 6, th effective efficiencies are plotted for fixed conical rib parameters (e/D = 0.0289, P/e = 800 W/m 2 of insolation. It is observed from the plots that the net effective efficie increased with increases in the temperature increase parameter and then decre continuously for all relative rib heights. However, the peaks of net effective effic were observed at different temperature increase parameters depending on the relativ height. The range of temperature parameters at which a higher net-effective efficiency observed is listed in Table 2. It is observed that a smooth SAH offered the best net effe efficiency when the temperature increase parameter was less than 0.00369 K·m 2 /W relative rib height parameter was dominant as the temperature rise parameter incre Different relative rib heights of 0.020, 0.0289 and 0.036 exhibited the best net effe efficiency in the following ranges of temperature rise parameters: 0.00369 < ΔT/I < 0. It can be seen from the plots that the mean temperature of the absorber plate decreased with the Reynolds number and became nearly constant. Contrary to this, the heat gain increased with the Reynolds number and became nearly flat for a high Reynolds number, implying that a lower plate temperature exhibited low heat loss through the glass cover and resulted in a high heat extraction rate by air from the absorber. On the other hand, the pumping power increased slightly with the Reynolds number, but the increment rate was not significant.

Effect of Relative Height
The net effective efficiency of the conical protrusion rib roughened absorber of an SAH was evaluated for all possible combinations of relative rib heights and relative pitches with 600 W/m 2 , 800 W/m 2 and 1000 W/m 2 of insolation. The net effective efficiency of a smooth SAH was also evaluated for comparison purposes. In Figure 6, the net effective efficiencies are plotted for fixed conical rib parameters (e/D = 0.0289, P/e = 10) at 800 W/m 2 of insolation. It is observed from the plots that the net effective efficiencies increased with increases in the temperature increase parameter and then decreased continuously for all relative rib heights. However, the peaks of net effective efficiency were observed at different temperature increase parameters depending on the relative rib height. The range of temperature parameters at which a higher net-effective efficiency was observed is listed in Table 2. It is observed that a smooth SAH offered the best net effective efficiency when the temperature increase parameter was less than 0.00369 K·m 2 /W. The relative rib height parameter was dominant as the temperature rise parameter increased. Different relative rib heights of 0.020, 0.0289 and 0.036 exhibited the best net effective efficiency in the following ranges of temperature rise parameters: 0.00369 < ∆T/I < 0.00463 K·m 2 /W, 0.00463 < ∆T/I < 0.00608 K·m 2 /W and 0.00608 < ∆T/I < 0.00691 K·m 2 /W. A relative rib height of 0.044 exhibited the best net effective efficiency at a temperature increase parameter of more than 0.0069 K·m 2 /W. Figure 7 shows the variation of the net effective efficiencies with Reynolds number for fixed conical rib parameters (P/e = 10) at 800 W/m 2 of insolation. It can be seen from the plots that net effective efficiencies increased with increases in the Reynolds number, reached a peak and then decreased continuously with increases in the Reynolds number. The peak of the net-effective efficiency was observed at different Reynolds number values depending on the relative rib height. Similarly, for maximum net effective efficiency, the ranges of the Reynolds number for different relative rib heights are listed in Table 2. The SAH without roughness (smooth duct) exhibited the best net effective efficiency with a value of the Reynolds number of more than 21,640. At a Reynolds number below 21,640, the conical protrusion rib roughness exhibited the best efficiency. Relative rib heights of 0.020, 0.0289 and 0.036 exhibited the best net effective efficiency in the following ranges of Reynolds numbers: 16,812 < Re < 21,640, 12,253 < ∆T/I < 16,812 and 11,095 < ∆T/I < 12,253. At a Reynolds number below 11,095, a relative height of 0.044 offered the best net-effective efficiency. The enhancement factors of net effective efficiency due to the conical protrusion rib roughness surface are listed in Table 3 for different relative rib heights.  Table 3 for different relative rib heights.

Effect of Relative Pitch
Similarly, the net effective efficiency of conical protrusion rib roughnesses for different relative pitches are plotted with temperature increase parameters at 800 W/m 2 of insolation, as shown in Figure 8. It is observed from the plots that the net effective efficiencies at different relative pitches increased with increases in the temperature increase parameter, reached a peak and then decreased with further increases in the temperature increase parameter. The peak of the net effective efficiency was observed at different temperature increase parameters depending on the relative rib pitch. The range of temperature parameters in which a higher net-effective efficiency was observed for a particular relative rib pitch are listed in Table 4. It can be seen that a smooth SAH offered the best net effective efficiency when the temperature increase parameters were less than 0.00365 K·m 2 /W. The relative rib height parameter was dominant when the temperature increase parameter increased beyond 0.00365 K·m 2 /W. A relative rib pitch of 12 exhibited the best net effective efficiency in the range of temperature increase parameters of 0.00365 < ∆T/I < 0.00562 K·m 2 /W. A relative rib pitch of 10 exhibited the best net. effective efficiency when the temperature increase parameter was more than 0.00562 K·m 2 /W. Figure 9 shows the variation of net effective efficiencies with Reynolds numbers for a fixed relative rib height (e/D = 0.00289) at 800 W/m 2 of insolation. It is observed that the net-effective efficiencies increased with an increase in the Reynolds number, reached a peak and then decreased continuously with increase in Reynolds number. The peak of net-effective efficiency has been observed at different Reynolds number values depending on the relative rib height. Similarly, for maximum net effective efficiency, the ranges of Reynolds numbers for different relative rib heights are listed in Table 4. A relative rib pitch of 10 of the conical protrusion rib exhibited the best net effective efficiency with a Reynolds number less than 13,520. A relative rib pitch of 10 exhibited the best net effective efficiency when the SAH operated at the range of Reynolds numbers of 13,520 < Re < 21,780. Beyond a Reynolds number of 21,780, the SAH duct without roughness (smooth duct) offered the best net effective efficiency in comparison to protrusion rib roughness in the SAH. Additionally, it can be seen from the plots that pitches of 6 and 8 did not contribute to a significant performance change. Enhancement factors for the net effective efficiency due to the conical protrusion rib roughness surface are also listed in Table 5 at different relative pitches.
Energies 2021, 14, x FOR PEER REVIEW 14 of 21 efficiency due to the conical protrusion rib roughness surface are also listed in Table 5 at different relative pitches.     efficiency due to the conical protrusion rib roughness surface are also listed in Table 5 at different relative pitches.    Figure 9. Effect of Reynolds number on effective efficiency.

Effect of Solar Insolation
In order to show the effect of solar insolation, the net effective efficiency of the conical protrusion rib roughness in the SAH was also evaluated for various kinds of solar insolation. Figure 10 shows the plots of net effective efficiency for a fixed roughness parameter (p/e = 10, e/D = 0.0289) at different insolations of 600 W/m 2 , 800 W/m 2 and 1000 W/m 2 . Similar plots are observed to those discussed in the previous sub-section. The peaks of the plots of net effective efficiency were found for different temperature increase parameters. The net effective efficiency rose with increases in the temperature increase parameter; thereafter, it decreased with further increases in the temperature increase parameter. Suddenly, the net effective efficiency began to decrease, indicating that there is large pumping power requirement. The rate of the decrement in net effective efficiency at 1000 W/m 2 was higher compared to the net effective efficiencies at 600 W/m 2 and 800 W/m 2 . This is due to the fact that a higher plate temperature is achieved due to higher insolation, leading to high top heat loss and consequently lower net effective efficiency.

Effect of Solar Insolation
In order to show the effect of solar insolation, the net effective efficiency of the conical protrusion rib roughness in the SAH was also evaluated for various kinds of solar insolation. Figure 10 shows the plots of net effective efficiency for a fixed roughness parameter (p/e = 10, e/D = 0.0289) at different insolations of 600 W/m 2 , 800 W/m 2 and 1000 W/m 2 . Similar plots are observed to those discussed in the previous sub-section. The peaks of the plots of net effective efficiency were found for different temperature increase parameters. The net effective efficiency rose with increases in the temperature increase parameter; thereafter, it decreased with further increases in the temperature increase parameter. Suddenly, the net effective efficiency began to decrease, indicating that there is large pumping power requirement. The rate of the decrement in net effective efficiency at 1000 W/m 2 was higher compared to the net effective efficiencies at 600 W/m 2 and 800 W/m 2 . This is due to the fact that a higher plate temperature is achieved due to higher insolation, leading to high top heat loss and consequently lower net effective efficiency. The results of the net effective efficiency due to conical protrusion rib roughness have been compared with the results for a semi-spherical dimpled rib roughness [23] and semispherical protrusion rib roughness [27] available in the literature. In Figure 11, the maximum net effective efficiencies of semi-spherical dimpled rib and semi-spherical protrusion rib roughness are plotted corresponding to their rib parameters (parameters of semi-spherical dimple rib p/e = 10, e/D 0.036 and α = 60° and parameter of semi-spherical protrusion rib p/e = 12, e/D 0.030 and α = 60°). The trend of the net effective efficiency of the conical protrusion rib roughness is similar to that of the trend of the semi-spherical protrusion rib roughness and semi-spherical dimpled rib roughness. The net effective The results of the net effective efficiency due to conical protrusion rib roughness have been compared with the results for a semi-spherical dimpled rib roughness [23] and semi-spherical protrusion rib roughness [27] available in the literature. In Figure 11, the maximum net effective efficiencies of semi-spherical dimpled rib and semi-spherical protrusion rib roughness are plotted corresponding to their rib parameters (parameters of semi-spherical dimple rib p/e = 10, e/D 0.036 and α = 60 • and parameter of semispherical protrusion rib p/e = 12, e/D 0.030 and α = 60 • ). The trend of the net effective efficiency of the conical protrusion rib roughness is similar to that of the trend of the semi-spherical protrusion rib roughness and semi-spherical dimpled rib roughness. The net effective efficiency with a conical protrusion rib roughness was greater than the net effective efficiency with a semi-spherical protrusion rib roughness at a low Reynolds number. Thereafter, the net effective efficiency with a semi-spherical protrusion rib was dominant and surpassed the net effective efficiency of the conical protrusion rib roughness. This occurs due to the dominance of the higher friction factor of the conical protrusion rib roughness, which leads to a large pumping power requirement. The sharp corners of conical ribs contribute to higher turbulence in comparison to the semi-spherical protrusion rib. As an effect of the large pumping power requirement, the net effective efficiency of the conical protrusion rib roughness decreases sharply below the net effective efficiency of the semi-spherical protrusion rib roughness at higher Reynolds numbers. efficiency with a conical protrusion rib roughness was greater than the net effective efficiency with a semi-spherical protrusion rib roughness at a low Reynolds number. Thereafter, the net effective efficiency with a semi-spherical protrusion rib was dominant and surpassed the net effective efficiency of the conical protrusion rib roughness. This occurs due to the dominance of the higher friction factor of the conical protrusion rib roughness, which leads to a large pumping power requirement. The sharp corners of conical ribs contribute to higher turbulence in comparison to the semi-spherical protrusion rib. As an effect of the large pumping power requirement, the net effective efficiency of the conical protrusion rib roughness decreases sharply below the net effective efficiency of the semi-spherical protrusion rib roughness at higher Reynolds numbers. Figure 11. Comparison of net effective efficiency with similar roughnesses.

Optimization of Conical Protrusion Roughness Parameters
Ranges of temperature increase parameters for various optimum rib parameters corresponding to the maximum net-effective efficiency have also been computed for insolations in the range of 600 W/m 2 to 1000 W/m 2 . Optimum values of the relative rib height of the conical protrusion rib roughness for various insolations (600, 800 and 1000 W/m 2 ) are presented in Figure 12. It was observed that a relative rib height of 0.044 was found to be optimum when the temperature increase parameter was more than 0.00789 K·m 2 /W for all insolations, while a smooth duct yielded the best effective efficiency when the temperature increase parameter was less than 0.00362 W/m 2 .K for all insolations. Furthermore, the optimum relative rib height of conical protrusion ribs was a function of insolation when the temperature increase parameter was in the following range: 0.00362 K·m 2 /W < ΔT/I < 0.00789 K·m 2 /W.

Optimization of Conical Protrusion Roughness Parameters
Ranges of temperature increase parameters for various optimum rib parameters corresponding to the maximum net-effective efficiency have also been computed for insolations in the range of 600 W/m 2 to 1000 W/m 2 . Optimum values of the relative rib height of the conical protrusion rib roughness for various insolations (600, 800 and 1000 W/m 2 ) are presented in Figure 12. It was observed that a relative rib height of 0.044 was found to be optimum when the temperature increase parameter was more than 0.00789 K·m 2 /W for all insolations, while a smooth duct yielded the best effective efficiency when the temperature increase parameter was less than 0.00362 W/m 2 .K for all insolations. Furthermore, the optimum relative rib height of conical protrusion ribs was a function of insolation when the temperature increase parameter was in the following range: 0.00362 K·m 2 /W < ∆T/I < 0.00789 K·m 2 /W.
Similarly, values of the optimum relative rib pitch for various temperature increase parameters are presented in Figure 13 for all insolations. It can be seen clearly that the smooth duct offered the highest effective efficiency over the conical protrusion rib roughness with all possible combination of rib parameters for all insolations when the temperature rise parameter was less than 0.00355 K·m 2 /W. However, a relative rib height of 10 offered the best effective efficiency when the temperature increase parameter was more than 0.00602 K·m 2 /W. Similarly, values of the optimum relative rib pitch for various temperature incr parameters are presented in Figure 13 for all insolations. It can be seen clearly tha smooth duct offered the highest effective efficiency over the conical protrusion roughness with all possible combination of rib parameters for all insolations when temperature rise parameter was less than 0.00355 K·m 2 /W. However, a relative rib he of 10 offered the best effective efficiency when the temperature increase parameter more than 0.00602 K·m 2 /W.
The optimum rib parameters can be determined from Figures 12 and 13 for g insolation and temperature rise parameters. Furthermore, the unique optim combination of rib parameters was found when ∆T/I > 0.00789 K·m 2 /W, and this optim combination comprised a relative pitch ratio of 10 and relative rib height of 0.044 fo values of insolation. Figure 13. Optimum value of relative rib pitch.

Conclusions
An analytical study has been conducted to predict the characteristics of the  Similarly, values of the optimum relative rib pitch for various temperature increase parameters are presented in Figure 13 for all insolations. It can be seen clearly that the smooth duct offered the highest effective efficiency over the conical protrusion rib roughness with all possible combination of rib parameters for all insolations when the temperature rise parameter was less than 0.00355 K·m 2 /W. However, a relative rib heigh of 10 offered the best effective efficiency when the temperature increase parameter was more than 0.00602 K·m 2 /W.
The optimum rib parameters can be determined from Figures 12 and 13 for given insolation and temperature rise parameters. Furthermore, the unique optimum combination of rib parameters was found when ∆T/I > 0.00789 K·m 2 /W, and this optimum combination comprised a relative pitch ratio of 10 and relative rib height of 0.044 for al values of insolation.

Conclusions
An analytical study has been conducted to predict the characteristics of the ne effective efficiency of a conical protrusion rib-roughened absorber surface in an SAH. In order to evaluate the enhancement factor, the net effective efficiency of a roughened absorber has also been compared to the net effective efficiency of a smooth absorber operating under similar conditions. On the basis of the results obtained, the conica The optimum rib parameters can be determined from Figures 12 and 13 for given insolation and temperature rise parameters. Furthermore, the unique optimum combination of rib parameters was found when ∆T/I > 0.00789 K·m 2 /W, and this optimum combination comprised a relative pitch ratio of 10 and relative rib height of 0.044 for all values of insolation.

Conclusions
An analytical study has been conducted to predict the characteristics of the net effective efficiency of a conical protrusion rib-roughened absorber surface in an SAH. In order to evaluate the enhancement factor, the net effective efficiency of a roughened absorber has also been compared to the net effective efficiency of a smooth absorber operating under similar conditions. On the basis of the results obtained, the conical protrusion rib parameters have been optimized for maximum net effective efficiency. Key findings of this study are given below.

1.
A conical protrusion rib roughness significantly affects the net effective efficiency of an SAH duct. An effective efficiency increase of up to 70.92% was obtained at an e/D of 0.0289 and p/e of 10; 2.
Net effective efficiency is observed to depend strongly on the Reynolds number: a higher Reynolds number always results in a relatively low value of effective efficiency irrespective of roughness parameters because of the very high frictional power requirements. Furthermore, in the lower Reynolds number range, the actual value of rib parameter determines the value of the effective efficiency; 3.
Net effective efficiency is also observed to be a function of insolation. The maximum effective efficiency increased from 69.82% to 70.92% when the insolation increased from 600 W/m 2 to 1000 W/m 2 ; 4.
A set optimum values of conical protrusion rib parameters exists that corresponds to specified operating conditions, resulting in maximum effective efficiency. The optimum relative rib heights have been found to be 0.020, 0.0289, 0.036 and 0.044 for temperature increase parameter ranges of 0.00369 < ∆T/I <0.00463 K·m 2 /W, 0.00463 < ∆T/I 0.00608 K·m 2 /W, 0.00608 < ∆T/I 0.00691 K·m 2 /W and 0.00691 < ∆T/I K·m 2 /W, respectively. Similarly, ranges of temperature increase parameters of 0.00365 < ∆T/I < 0.00562 K·m 2 /W and 0.00365 < ∆T/I K·m 2 /W have been found in which relative rib pitches of 12 and 10, respectively, exhibit the best net effective efficiency; 5.
Optimum values of the relative rib pitch and relative rib height vary with the temperature increase parameter, and ranges of the temperature increase parameter for optimum roughness parameters change slightly with insolation; 6.
A unique combination of an optimum relative rib height of 0.44 and relative rib pitch of 10 are observed regardless of the insolation value when ∆T/I > 0.00789 K·m 2 /W.
Thermo-hydraulic performance analysis has been carried out to arrive at the optimum values of conical rib protrusion rib parameters that result in maximum net useful gain for the given operating conditions. The characteristics of net effective efficiency will help designers to determine conical protrusion rib parameters under different operating conditions.