Assessment of Thermal Comfort in the Intelligent Buildings in View of Providing High Quality Indoor Environment

: The paper analyses the indoor environment in two modern intelligent buildings located in Poland. Measurements of air and globe temperatures, relative humidity and carbon dioxide concentration in 117 rooms carried out in the space of 1.5 years were presented. Thermal comfort of the occupants has been investigated using a questionnaire survey. Based on 1369 questionnaires, thermal sensation, acceptability and preference votes were analysed in view of their interdependency as well as their dependency on operative temperature, which proved to be very strong. It has been found that the respondents did not completely rate thermal comfort and indoor environment quality as very high, although the overwhelming sensations were positive. Apart from the operation of heating, ventilation and air conditioning (HVAC) systems, this might have also been the cause of individual human factors, such as body mass index, as tested in the study, or the ﬁnding that people were generally in favour of a warmer environment. Moreover, thermal environment proved to be the most important element for ensuring the well-being of the occupants.


Introduction
Energy consumption throughout the world constantly rises. Much of it is related to the use in the building sector, especially for the development and daily operation of sophisticated modern buildings such as large-scale intelligent buildings for office and public use. Those types of buildings are equipped with services and installations such as heating, ventilation and air conditioning (HVAC) systems, whose energy consumption might be significant. In commercial facilities the main electrical loads are typically related to HVAC systems and lighting [1], in office buildings heating, ventilation and air conditioning systems may account for over 60% of energy consumption [2], while data from three years of final energy consumption in a modern educational building in France indicate over 80% energy use for heating and ventilation [3]. Thus, even a small reduction in indoor air temperature classrooms located in a school in Slovakia. The following parameters were measured: temperature, relative humidity, solid particles, CO 2 concentration, sound level as well as lighting conditions. The number of people tested was 34 students of 6-15 years old and five teachers. Thermal sensations were overwhelmingly acceptable and perceived as good. A concern was the relatively high CO 2 level (in the range from 577 to 1787 ppm) despite the fact that windows were open. The concentration of carbon dioxide fluctuated during the school hours. Fang et al. [22] analysed thermal comfort in air-conditioned classrooms located in Hong Kong. The research programme consisted of measurements of environmental parameters as well as thermal responses from 982 students. The authors found out that there was an insignificant difference between the temperature preferred by the respondents and the neutral temperature. Besides, there was a strong linear relation between the mean thermal sensation vote and the operative temperature. Buratti and Ricciardi [23] used direct measurements of the indoor microclimate parameters and the questionnaires during autumn, winter and spring in classrooms at the University of Perugia, Terni and Pavia in Italy. The internal air temperatures ranged from 20.9 to 26.4 • C, mean radiant temperatures from 20.1 to 25.1 • C, while relative humidity from 25% to 63.7%. Air movement was low, with maximal air velocity of 0.085 m/s. Thermal sensations experienced by the respondents in the considered classrooms proved to be very satisfactory (mostly falling within the acceptable range of −0.5-0.5, except for two surveys that produced the results of thermal sensation vote of 0.6 and 0.78). A later work by these authors [24] provided more diversified results. It also focused on other parameters affecting the human well-being, namely: acoustic and lightning conditions. The tests were conducted in classrooms at the University of Pavia in Italy. The tests covered measurements of physical parameters (indoor and external air temperature and relative humidity, mean radiant temperature and air velocity) and questionnaires for respondents' responses (whose total number was 331). It was observed that the average values of PMV and PPD for women and men can differ from each other (maximally by 0.45% and 11.57%, respectively). Generally, thermal comfort could be considered as very good for three classrooms (mean thermal sensation vote ranged from 0.08 to 0.36) and unsatisfactory for two (where mean sensation vote reached 1.15 and −1.10). Aghniaey et al. [25] provided data on thermal comfort at the University of Georgia'a campus in US. The results were obtained in 11 classrooms where the number of students ranged from 18 to 54 persons. The operative temperature was between 21 and 27 • C. The study showed that the thermal environment in the analysed classrooms was overwhelmingly acceptable. The average thermal preference vote was "no change" if the indoor operative temperature was ca. 23.5 • C (thus, this temperature value can be considered optimal at the considered location). For this temperature the actual mean vote was almost neutral. Women typically preferred warmer thermal environments and on average female thermal sensation votes were lower than those for men.
It needs to be noted that the optimal human thermal conditions are subjective and depend on the climate. Experimental results on thermal comfort tests conducted in the summer season in India [26] reveal that the mean comfort temperature (determined by Griffiths' method) was 29.8 • C. In this paper thermal comfort of 900 students (mostly males) in naturally ventilated classrooms during the summer in India was analysed. The study covered thermal sensations, preferences and acceptability as well as measurements of environmental parameters. The mean indoor air temperature was 30.4 • C (from the range of ca. 26.6 to ca. 36 • C), while mean relative humidity was 39.4% and clothing thermal resistance ranged from ca. 0.41% to ca. 59% of votes which indicated the neutral thermal sensation and 69% chose "no change" as their thermal preference. About 81% of the responses were in the comfort band. Thus, the research shows that the overwhelming majority was satisfied with the conditions that might be considered unsatisfactory for the European respondents.
One of the relatively few works on thermal comfort in intelligent educational buildings has been presented by Merabtine et al. [3]. The authors investigated indoor air quality and thermal comfort in a low energy consumption building in France. The authors tested 41 students between the ages of 17 and 22 years using questionnaires in the foyer of the building. The indoor air parameters were measured. The obtained results indicate a dissatisfaction with the thermal conditions in the considered Energies 2020, 13,1973 4 of 20 space (beyond the 10% acceptance level of PPD). Thermal sensation votes were also outside of the acceptable range and fell below −1. When the occupancy in the building was high the CO 2 levels exceeded the limit of 820 ppm, but it was rare (1-5% of occupancy hours). In the tested three teacher rooms, the indoor air temperature ranged from ca. 20.3 to 24.7 • C, while CO 2 concentration from ca. over 300 up to over 1300 ppm. Based on these data, it can be concluded that even such modern buildings might not offer comfortable conditions to their users. Carbon dioxide concentration proved to exceed the upper limit at times, while thermal sensation votes of the respondents indicated the feeling of dissatisfaction.
Apart from schools and university campuses, office buildings are also locations where people spend a great deal of time, either as employees or clients. Thus, the energy performance and thermal comfort of the occupants are a crucial issue.
Moujalled et al. [2] conducted thermal comfort measurement in five naturally ventilated office buildings in the south of France. The indoor air temperatures ranged from 21.1 to 32.9 • C. In total 120 people took part in the survey, generating 374 data sets. It was concluded that during the warm season over half of the respondents were dissatisfied with the indoor microclimate. During the cold season over 90% were comfortable. The thermal sensation votes proved to be well correlated with the operative temperature. The room users turned out to be less sensitive to an increase in temperature during the warm season.
Hens [27] performed questionnaire and direct measurement surveys in two air-conditioned office buildings in Belgium. It was reported that the number of the dissatisfied at the mean vote of 0 was greater than 5% (as given in the standard based on the Fanger model). A relatively high number of health complaints was reported by the occupants, who suffered from headache (ca. 44% of respondents), dry throat or blocked nose (over 30%). This might influence the subjective thermal sensation votes expressed by the people.
Kuchen and Fisch [28] conducted tests in 148 work spaces in 25 office buildings at different locations in Germany. The total number of measurements was 345 and all took place during winter (not older than ten years). The most preferred operative temperature value was within the range of 21-22 • C (here, the average thermal sensation vote was 0.08 and 0.12, respectively). The authors observed a relatively good linear relation between the operative temperature and neutral temperature.
Ricciardi and Buratti [29] experimentally analysed thermal comfort in nine open space offices in Italy. Indoor environmental parameters were measured and 588 questionnaires were statistically considered. Indoor air temperature ranged from 22.1 to 26.2 • C. Thermal sensation proved to be generally fine with PMV values ranging from −1.38 to +2.00 and a high mean thermal dissatisfaction of 60% was observed. The correlation between operative temperature vs. PMV was considered good and between neutral and operative temperatures relatively good.
Indraganti et al. [30] conducted tests in four office buildings in Japan during the summer. Four environmental as well as two personal variables were measured together with CO 2 concentration, while 435 occupants were surveyed (which produced 2402 questionnaires). The mean indoor air temperature was 28.2 • C, while mean CO 2 concentration 1055 ppm. The comfort temperature turned out to be 27.1 • C. The majority of people voted in the comfort band of −1 to +1, thus thermal acceptability from the questionnaires proved to be high. The authors observed that the mean sensation vote in buildings with natural ventilation was always higher than in air conditioned buildings. This finding was partly confirmed in another paper by the same authors [31], who performed tests in 25 office buildings in India. However, in this case-having analysed 2612 questionnaires from 1658 volunteers-they found that thermal acceptability was generally low (62.5%), especially in buildings with natural ventilation.
The results of the experimental work of Jazizadeh et al. [32] on thermal comfort in office buildings reveal that ambient temperature is the most important parameter in terms of the thermal sensation of users. However, other factors (not often investigated) such as carbon dioxide concentration and light intensity also play a role-in some rooms their impact in smaller and in some larger in comparison to humidity. Szabo and Kajtar [33] investigated the influence on the type HVAC system on thermal Energies 2020, 13, 1973 5 of 20 comfort in three office buildings. The best results were obtained for the ducted fan-coil with suspended ceiling installation. The indoor air quality measured with the CO 2 concentration proved to be high in all the buildings. Fedorczak-Cisak et al. [34] considered the impact of external shading equipment in office rooms with large glazed areas on indoor thermal comfort. It was observed that the application of external Venetian blinds reduced the ambient air temperatures and the number of discomfort hours by 92%. However, the tests did not cover the actual thermal sensation measurements based on human responses-only calculated results of PMV and PPD were provided according to the standard.
Due to the fact that heating, ventilation and air conditioning systems in buildings consume much thermal and electrical energy, any reduction in heating during the cold season (linked with decreased indoor temperatures) and in cooling requirements in summer (leading to elevated indoor temperatures) may provide significant economic and environmental savings. However, such adjustments should not have an unfavourable impact on the thermal comfort of the occupants. Thus, more information is needed as to the acceptable levels of indoor microclimate parameters. Moreover, the indoor environment might have an impact on work productivity [35] and learning performance [36,37]. Thus, the issue of ensuring thermal comfort conditions needs to be considered already at an early design stage of public utility buildings.
The paper analyses thermal comfort and general sensation experienced by people in two intelligent buildings located in Poland, seventy kilometers apart from each other. Based on the literature review, it needs to be noted that such a comprehensive study focused on the eastern European region, as presented in this paper, has not been found in literature.

Materials and Methods
The analysis covered two modern intelligent buildings in Poland. The first one is an educational facility "Energis" housing the Faculty of Environmental, Geomatic and Energy Engineering of Kielce University of Technology (Figure 1), while the second is the courthouse in Radom (Figure 2). impact of external shading equipment in office rooms with large glazed areas on indoor thermal comfort. It was observed that the application of external Venetian blinds reduced the ambient air temperatures and the number of discomfort hours by 92%. However, the tests did not cover the actual thermal sensation measurements based on human responses-only calculated results of PMV and PPD were provided according to the standard. Due to the fact that heating, ventilation and air conditioning systems in buildings consume much thermal and electrical energy, any reduction in heating during the cold season (linked with decreased indoor temperatures) and in cooling requirements in summer (leading to elevated indoor temperatures) may provide significant economic and environmental savings. However, such adjustments should not have an unfavourable impact on the thermal comfort of the occupants. Thus, more information is needed as to the acceptable levels of indoor microclimate parameters. Moreover, the indoor environment might have an impact on work productivity [35] and learning performance [36,37]. Thus, the issue of ensuring thermal comfort conditions needs to be considered already at an early design stage of public utility buildings.
The paper analyses thermal comfort and general sensation experienced by people in two intelligent buildings located in Poland, seventy kilometers apart from each other. Based on the literature review, it needs to be noted that such a comprehensive study focused on the eastern European region, as presented in this paper, has not been found in literature.

Materials and Methods
The analysis covered two modern intelligent buildings in Poland. The first one is an educational facility "Energis" housing the Faculty of Environmental, Geomatic and Energy Engineering of Kielce University of Technology (Figure 1), while the second is the courthouse in Radom ( Figure 2).    impact of external shading equipment in office rooms with large glazed areas on indoor thermal comfort. It was observed that the application of external Venetian blinds reduced the ambient air temperatures and the number of discomfort hours by 92%. However, the tests did not cover the actual thermal sensation measurements based on human responses-only calculated results of PMV and PPD were provided according to the standard. Due to the fact that heating, ventilation and air conditioning systems in buildings consume much thermal and electrical energy, any reduction in heating during the cold season (linked with decreased indoor temperatures) and in cooling requirements in summer (leading to elevated indoor temperatures) may provide significant economic and environmental savings. However, such adjustments should not have an unfavourable impact on the thermal comfort of the occupants. Thus, more information is needed as to the acceptable levels of indoor microclimate parameters. Moreover, the indoor environment might have an impact on work productivity [35] and learning performance [36,37]. Thus, the issue of ensuring thermal comfort conditions needs to be considered already at an early design stage of public utility buildings.
The paper analyses thermal comfort and general sensation experienced by people in two intelligent buildings located in Poland, seventy kilometers apart from each other. Based on the literature review, it needs to be noted that such a comprehensive study focused on the eastern European region, as presented in this paper, has not been found in literature.

Materials and Methods
The analysis covered two modern intelligent buildings in Poland. The first one is an educational facility "Energis" housing the Faculty of Environmental, Geomatic and Energy Engineering of Kielce University of Technology (Figure 1), while the second is the courthouse in Radom ( Figure 2).    Definitions of "intelligent buildings" have changed and evolved over time as pointed out in the review paper [38], however according to the classic definition proposed by Leifer [39] the fundamental constituents of such buildings are, among others: automation, building management systems, information communication networks.
Both the considered buildings are equipped with heating, ventilation and air conditioning as well as building management systems. The air processing units filter the outside air and preheat it (if necessary) before it is supplied via the ductwork to individual rooms. In those units, moisture and heat are recovered with the rotary heat exchangers. However, radiators and floor heating (only in the Energis building) are the main sources of heat. Cooling is provided with fan-coil devices in the courthouse and with 4-way ceiling-mounted indoor units in Energis. The cooling liquid (solution of ethylene glycol) is cooled with chillers located on the rooftops and circulated to indoor units if there is such a need. Each room is equipped with temperature control panel that enables occupants to set the required temperature value. However, this parameter can also be set by the building operator using the building management system (BMS) interface. This system also enables full monitoring of the buildings' parameters, including energy consumption and generation (only in Energis, where electricity is produced from photovoltaic panels, while heat is provided using heat pumps and solar collectors), lighting, access to rooms as well as weather data. Apart from that, it integrates visual anti-theft monitoring, fire protection systems and other functions. BMS can be accessed via internet and the operators can maintain constant remote control over the buildings. Thus, such a complete integration of the HVAC and monitoring systems with BMS as well as the use of automation and control in order to provide the occupants with the adequate indoor conditions can be considered as building "intelligence". Individual occupants of rooms can also consider the building as intelligent, because it can maintain the pre-set indoor conditions despite changes occurring outdoors or indoors.
Both these buildings are fairly new and are located about seventy kilometers from one another. The Energis building was completed in the year 2012, while the courthouse in 2017. Table 1 summarises their main technical data. The buildings have been properly insulated to ensure low heat losses to the environment, which is particularly important in Poland, where winters can be severe with outside air temperatures falling to ca. −25 • C. The thermographic analysis conduced in both buildings revealed no major problems or defects. Figures 3 and 4 present the investigation results of thermal fields observed from the outside and in selected rooms.
Energies 2020, 13, x FOR PEER REVIEW 6 of 20 Definitions of "intelligent buildings" have changed and evolved over time as pointed out in the review paper [38], however according to the classic definition proposed by Leifer [39] the fundamental constituents of such buildings are, among others: automation, building management systems, information communication networks.
Both the considered buildings are equipped with heating, ventilation and air conditioning as well as building management systems. The air processing units filter the outside air and preheat it (if necessary) before it is supplied via the ductwork to individual rooms. In those units, moisture and heat are recovered with the rotary heat exchangers. However, radiators and floor heating (only in the Energis building) are the main sources of heat. Cooling is provided with fan-coil devices in the courthouse and with 4-way ceiling-mounted indoor units in Energis. The cooling liquid (solution of ethylene glycol) is cooled with chillers located on the rooftops and circulated to indoor units if there is such a need. Each room is equipped with temperature control panel that enables occupants to set the required temperature value. However, this parameter can also be set by the building operator using the building management system (BMS) interface. This system also enables full monitoring of the buildings' parameters, including energy consumption and generation (only in Energis, where electricity is produced from photovoltaic panels, while heat is provided using heat pumps and solar collectors), lighting, access to rooms as well as weather data. Apart from that, it integrates visual anti-theft monitoring, fire protection systems and other functions. BMS can be accessed via internet and the operators can maintain constant remote control over the buildings. Thus, such a complete integration of the HVAC and monitoring systems with BMS as well as the use of automation and control in order to provide the occupants with the adequate indoor conditions can be considered as building "intelligence". Individual occupants of rooms can also consider the building as intelligent, because it can maintain the pre-set indoor conditions despite changes occurring outdoors or indoors.
Both these buildings are fairly new and are located about seventy kilometers from one another. The Energis building was completed in the year 2012, while the courthouse in 2017. Table 1 summarises their main technical data. The buildings have been properly insulated to ensure low heat losses to the environment, which is particularly important in Poland, where winters can be severe with outside air temperatures falling to ca.   It needs to be noted that Energis is close to the passive building standard. It utilises a number of renewable energy sources such as ground and air source heat pumps, solar panels as well as photovoltaic systems.
The tests were conducted in the space of 1.5 years, between February 2017 and July 2018, which enabled us to cover all the seasons. They consisted of simultaneous measurement of environmental physical parameters in rooms, namely: air temperature, globe temperature, air velocity, relative humidity and carbon dioxide concentration. The tests have been performed with two devices, first of all with BABUC-A data logger (by the Italian company Lsi-Lastem) as well as a microclimate meter Sensotron PS32 (by the Polish company Sensotron). Additionally, the infrared images were obtained with FLIR E5 thermovision camera in order to determine possible presence of thermal bridges. Table  2 presents the details of the testing equipment.   It needs to be noted that Energis is close to the passive building standard. It utilises a number of renewable energy sources such as ground and air source heat pumps, solar panels as well as photovoltaic systems.
The tests were conducted in the space of 1.5 years, between February 2017 and July 2018, which enabled us to cover all the seasons. They consisted of simultaneous measurement of environmental physical parameters in rooms, namely: air temperature, globe temperature, air velocity, relative humidity and carbon dioxide concentration. The tests have been performed with two devices, first of all with BABUC-A data logger (by the Italian company Lsi-Lastem) as well as a microclimate meter Sensotron PS32 (by the Polish company Sensotron). Additionally, the infrared images were obtained with FLIR E5 thermovision camera in order to determine possible presence of thermal bridges. Table 2 presents the details of the testing equipment. The measuring device was located on the tripod in the central part of the analysed rooms. Figure 5a and b present the experimental set-up in a lecture room in the Energis building and in an office in the courthouse, respectively. The measuring device was located on the tripod in the central part of the analysed rooms. Figure 5a and b present the experimental set-up in a lecture room in the Energis building and in an office in the courthouse, respectively. The tests were carried out in 47 different rooms in both buildings. The largest number of people in one room (a lecture theater in the Energis building) was 65. The data obtained in the course of the experiment were recorded and stored for further processing. At the same time as the measurements were taken, the occupants of a given room were provided with questionnaires. These volunteers were asked to answer 36 questions regarding their thermal sensation, preference and acceptability as well as humidity, air quality, activity level before coming to the room, and clothing etc. In total, 118 measurements were taken in different rooms (some were used more than once)-77 comprised of rooms with at least 5 people while 41 in rooms of fewer than 5 users. The total number of questionnaires was 1501, while 1369 of these related to rooms containing at least 5 people. The database consisted of votes from healthy people only (questionnaires, in which the respondent expressed that he/she was ill were not considered). It results from the fact that thermal sensation of people who are unwell might not be objective. The measurements and the questionnaire survey were performed after at least 30 min of the occupants entering the room. This time is enough to adopt to the new environment, as pointed out by Mishra et al. [40].
The monitoring activities in each room lasted up to 1-1.2 h. Upon switching on, the measuring system required a certain amount of time to stabilise and the respondents needed to accommodate to the environment and its conditions (up to 30-40 min). After that time the volunteers were asked to fill in the questionnaires. The sampling rate was set at 1 min. The measurement results of the physical parameters taken during and shortly before the respondents filled in the questionnaires indicate that the levels of all the parameters, except for the carbon dioxide concentration, were quite stable (with standard deviation values not exceeding the measurement error, as given in Table 2). In terms of the CO2 concentration, it is significantly dependent on the number of people in each room. Generally, room occupancy was high for the office rooms in the courthouse and varied considerably during lectures in the Energis building (Table S1 in the Supplementary material provides details on  room occupancy, while Table S2 shows carbon dioxide concentration). Generally, almost all the lecture rooms and classrooms in the building were occupied at the time of measurements. However, sometimes the attendance was low and/or a relatively small group occupied a large room.
The largest number of respondents were full-time students in the Energis building. Their age typically ranged from 19 to 24 years old, while the age of office workers employed at the courthouse varied significantly and was up to 63 years old. Generally, the average age of all the respondents was 25.1 (standard deviation 8.5), while the median age was 22. The body mass index (BMI) ranged from The tests were carried out in 47 different rooms in both buildings. The largest number of people in one room (a lecture theater in the Energis building) was 65. The data obtained in the course of the experiment were recorded and stored for further processing. At the same time as the measurements were taken, the occupants of a given room were provided with questionnaires. These volunteers were asked to answer 36 questions regarding their thermal sensation, preference and acceptability as well as humidity, air quality, activity level before coming to the room, and clothing etc. In total, 118 measurements were taken in different rooms (some were used more than once)-77 comprised of rooms with at least 5 people while 41 in rooms of fewer than 5 users. The total number of questionnaires was 1501, while 1369 of these related to rooms containing at least 5 people. The database consisted of votes from healthy people only (questionnaires, in which the respondent expressed that he/she was ill were not considered). It results from the fact that thermal sensation of people who are unwell might not be objective. The measurements and the questionnaire survey were performed after at least 30 min of the occupants entering the room. This time is enough to adopt to the new environment, as pointed out by Mishra et al. [40].
The monitoring activities in each room lasted up to 1-1.2 h. Upon switching on, the measuring system required a certain amount of time to stabilise and the respondents needed to accommodate to the environment and its conditions (up to 30-40 min). After that time the volunteers were asked to fill in the questionnaires. The sampling rate was set at 1 min. The measurement results of the physical parameters taken during and shortly before the respondents filled in the questionnaires indicate that the levels of all the parameters, except for the carbon dioxide concentration, were quite stable (with standard deviation values not exceeding the measurement error, as given in Table 2). In terms of the CO 2 concentration, it is significantly dependent on the number of people in each room. Generally, room occupancy was high for the office rooms in the courthouse and varied considerably during lectures in the Energis building (Table S1 in the Supplementary material provides details on room  occupancy, while Table S2 shows carbon dioxide concentration). Generally, almost all the lecture rooms and classrooms in the building were occupied at the time of measurements. However, sometimes the attendance was low and/or a relatively small group occupied a large room.
The largest number of respondents were full-time students in the Energis building. Their age typically ranged from 19 to 24 years old, while the age of office workers employed at the courthouse varied significantly and was up to 63 years old. Generally, the average age of all the respondents was 25.1 (standard deviation 8.5), while the median age was 22. The body mass index (BMI) ranged from

Indoor Air Parameters in the Intelligent Buildings
Both Energis and Courthouse intelligent buildings have been designed and built to ensure proper indoor air conditions for people, who are currently there. However, despite much investment cost, the indoor air parameters determined in the course of the experimental programme sometimes proved to be less then satisfactory. Figure 6 presents the test results of relative humidity and operative temperature for 118 rooms (some tested more than once). The operative temperature has been calculated as the arithmetic mean of indoor air and mean radiant temperatures (as in [25]) due to the low values of air velocity.

Indoor Air Parameters in the Intelligent Buildings
Both Energis and Courthouse intelligent buildings have been designed and built to ensure proper indoor air conditions for people, who are currently there. However, despite much investment cost, the indoor air parameters determined in the course of the experimental programme sometimes proved to be less then satisfactory. Figure 6 presents the test results of relative humidity and operative temperature for 118 rooms (some tested more than once). The operative temperature has been calculated as the arithmetic mean of indoor air and mean radiant temperatures (as in [25]) due to the low values of air velocity. For some rooms the test results indicate that the indoor microclimate can be considered unsatisfactory. Operative temperature exceeds the maximal value of 26 °C as given in the standard [8] for eleven measurement sets (ca. 9% of cases). Although, it needs to be noted that this might have happened due to the preference of the room occupants, who might have liked such warm environments and were unwilling to switch on air cooling. In terms of relative humidity, its optimal value depends on a number of parameters, however some data points in Figure 6 fall below the 25% level (almost 7% of cases). Consequently, a sensation of discomfort might be generated, if solid particles or other air contaminants are present in the air.
During the surveys carbon dioxide concentration was also determined. Its required value, like in the case of operative temperature, depends on the building category. For the buildings within category II (to which both analysed buildings belong) the upper limit is 800 ppm plus the outside air CO2 level [8]. Figure 7 presents the data of indoor air temperature and carbon dioxide concentration from 118 measurement sets. The analysis of the figure indicate that some measurements are characterised by elevated levels of carbon dioxide concentration. For some rooms the test results indicate that the indoor microclimate can be considered unsatisfactory. Operative temperature exceeds the maximal value of 26 • C as given in the standard [8] for eleven measurement sets (ca. 9% of cases). Although, it needs to be noted that this might have happened due to the preference of the room occupants, who might have liked such warm environments and were unwilling to switch on air cooling. In terms of relative humidity, its optimal value depends on a number of parameters, however some data points in Figure 6 fall below the 25% level (almost 7% of cases). Consequently, a sensation of discomfort might be generated, if solid particles or other air contaminants are present in the air.
During the surveys carbon dioxide concentration was also determined. Its required value, like in the case of operative temperature, depends on the building category. For the buildings within category II (to which both analysed buildings belong) the upper limit is 800 ppm plus the outside air CO 2 level [8]. Figure 7 presents the data of indoor air temperature and carbon dioxide concentration from 118 measurement sets. The analysis of the figure indicate that some measurements are characterised by elevated levels of carbon dioxide concentration.
Undoubtedly, the indoor air parameters can be improved in order to provide more comfort to the occupants. Another issue is the subjective assessment and responses of room users to such indoor conditions. It was reflected in the questionnaires filled in at the same time as the measurements of the physical parameters were taken. The following sections discuss this problem in detail. Energies 2020, 13, x FOR PEER REVIEW 10 of 20 Undoubtedly, the indoor air parameters can be improved in order to provide more comfort to the occupants. Another issue is the subjective assessment and responses of room users to such indoor conditions. It was reflected in the questionnaires filled in at the same time as the measurements of the physical parameters were taken. The following sections discuss this problem in detail.

Thermal Sensation, Acceptability and Preference of the Occupants
The individuals expressed their responses to the thermal environment in the questionnaire survey. The average value for each room was calculated based on the answers. Thus, only rooms with at least five people were considered to generate the average (arithmetic mean) value of a given parameter. The first question in the questionnaire was: "How do you assess your current thermal sensation". The possible responses to choose from were: "too hot" (+3), "too warm" (+2), "pleasantly warm" (+1), "neutral" (0), "pleasantly cool" (-1), "too cool" (-2), "too cold" (-3). The comfort area ranged from -1 to +1. Other responses indicate unsatisfactory thermal comfort of the respondents. Figure 8 presents the combined results of 1369 responses as measured in 77 rooms (some were used more than once). Male and female votes were calculated separately, but placed in the same graph for comparison.

Thermal Sensation, Acceptability and Preference of the Occupants
The individuals expressed their responses to the thermal environment in the questionnaire survey. The average value for each room was calculated based on the answers. Thus, only rooms with at least five people were considered to generate the average (arithmetic mean) value of a given parameter. The first question in the questionnaire was: "How do you assess your current thermal sensation". The possible responses to choose from were: "too hot" (+3), "too warm" (+2), "pleasantly warm" (+1), "neutral" (0), "pleasantly cool" (−1), "too cool" (−2), "too cold" (−3). The comfort area ranged from −1 to +1. Other responses indicate unsatisfactory thermal comfort of the respondents. Figure 8 presents the combined results of 1369 responses as measured in 77 rooms (some were used more than once). Male and female votes were calculated separately, but placed in the same graph for comparison. Undoubtedly, the indoor air parameters can be improved in order to provide more comfort to the occupants. Another issue is the subjective assessment and responses of room users to such indoor conditions. It was reflected in the questionnaires filled in at the same time as the measurements of the physical parameters were taken. The following sections discuss this problem in detail.

Thermal Sensation, Acceptability and Preference of the Occupants
The individuals expressed their responses to the thermal environment in the questionnaire survey. The average value for each room was calculated based on the answers. Thus, only rooms with at least five people were considered to generate the average (arithmetic mean) value of a given parameter. The first question in the questionnaire was: "How do you assess your current thermal sensation". The possible responses to choose from were: "too hot" (+3), "too warm" (+2), "pleasantly warm" (+1), "neutral" (0), "pleasantly cool" (-1), "too cool" (-2), "too cold" (-3). The comfort area ranged from -1 to +1. Other responses indicate unsatisfactory thermal comfort of the respondents. Figure 8 presents the combined results of 1369 responses as measured in 77 rooms (some were used more than once). Male and female votes were calculated separately, but placed in the same graph for comparison.   The research has shown that 66.3% of women and 76.4% of men felt comfortable (votes in the range of −1 to +1), while the rest felt uncomfortable (those defined as the total number of votes: +3, +2, −2, −3). The standards [6,8] stipulate that the percentage of people dissatisfied (PPD) with the microclimate should not exceed 10% for the buildings registered as category II. Thus, it can be concluded that generally the analysed modern intelligent buildings did not offer the proposed level of microclimate comfort conditions at the considered time span, during which the tests were performed. This phenomenon will be further considered in Figures 9 and 10, which present the thermal acceptability and thermal preference votes.
Energies 2020, 13,1973 11 of 20 -2, -3). The standards [6,8] stipulate that the percentage of people dissatisfied (PPD) with the microclimate should not exceed 10% for the buildings registered as category II. Thus, it can be concluded that generally the analysed modern intelligent buildings did not offer the proposed level of microclimate comfort conditions at the considered time span, during which the tests were performed. This phenomenon will be further considered in Figures 9 and 10, which present the thermal acceptability and thermal preference votes.  The acceptability of room users was determined by them in the questionnaires as the answer to the question: "How do you rate your thermal environment?" The possible answers were: "absolutely acceptable" (+2), "still acceptable" (+1), "already unacceptable" (-1), "absolutely unacceptable" (-2). Figure 9 presents the combined results of 1369 responses.
Although Figure 8 suggested a large number of people dissatisfied, the acceptability vote ( Figure 9) does not reflect that assumption completely. It has been determined that ca. 17% of women rated the environment as unacceptable (votes: -2 and -1) and only almost 12% of men. It has microclimate should not exceed 10% for the buildings registered as category II. Thus, it can be concluded that generally the analysed modern intelligent buildings did not offer the proposed level of microclimate comfort conditions at the considered time span, during which the tests were performed. This phenomenon will be further considered in Figures 9 and 10, which present the thermal acceptability and thermal preference votes.  The acceptability of room users was determined by them in the questionnaires as the answer to the question: "How do you rate your thermal environment?" The possible answers were: "absolutely acceptable" (+2), "still acceptable" (+1), "already unacceptable" (-1), "absolutely unacceptable" (-2). Figure 9 presents the combined results of 1369 responses.
Although Figure 8 suggested a large number of people dissatisfied, the acceptability vote ( Figure 9) does not reflect that assumption completely. It has been determined that ca. 17% of women rated the environment as unacceptable (votes: -2 and -1) and only almost 12% of men. It has The acceptability of room users was determined by them in the questionnaires as the answer to the question: "How do you rate your thermal environment?" The possible answers were: "absolutely acceptable" (+2), "still acceptable" (+1), "already unacceptable" (−1), "absolutely unacceptable" (−2). Figure 9 presents the combined results of 1369 responses.
Although Figure 8 suggested a large number of people dissatisfied, the acceptability vote ( Figure 9) does not reflect that assumption completely. It has been determined that ca. 17% of women rated the environment as unacceptable (votes: −2 and −1) and only almost 12% of men. It has also been revealed that almost 28% of women and over 32% of men were absolutely pleased with the indoor environment conditions. The questionnaire also contained the question about thermal preference. The occupants were asked to express their opinion on the following issue: "I would like in this room to be: "much warmer" (+2), "warmer" (+1), "no change" (0), "cooler" (−1), "much cooler" (−2). Figure 10 presents the combined results of 1369 responses as in the previous figures. The greatest number of respondents (ca. 46% of women and 57% of men) opted for "no change" answer. The others wanted a smaller or larger change. Many room users would like the environment to be cooler (ca. 24% for both men and women) or warmer (20.5% for women and 11.5% for men). The other votes, namely those of "much warmer" and "much cooler" did not exceed 5.5%.
The analysis of the data on thermal sensation, acceptability and preference indicate that the buildings, despite their sophistication and energy input, did not offer the highest level of thermal comfort. Since this parameter is considered to be mostly influenced by indoor thermal parameters, the following figures present the relationships between the operative temperature and thermal sensation (Figure 11), acceptability ( Figure 12) and preference ( Figure 13) in order to investigate the impact of operative temperature in detail. Here, average votes of thermal sensation, acceptability and preference have been considered for 77 groups of respondents in the considered rooms. Each group consisted of between 5 and 65 people.
indoor environment conditions. The questionnaire also contained the question about thermal preference. The occupants were asked to express their opinion on the following issue: "I would like in this room to be: "much warmer" (+2), "warmer" (+1), "no change" (0), "cooler" (-1), "much cooler" (-2). Figure 10 presents the combined results of 1369 responses as in the previous figures. The greatest number of respondents (ca. 46% of women and 57% of men) opted for "no change" answer. The others wanted a smaller or larger change. Many room users would like the environment to be cooler (ca. 24% for both men and women) or warmer (20.5% for women and 11.5% for men). The other votes, namely those of "much warmer" and "much cooler" did not exceed 5.5%.
The analysis of the data on thermal sensation, acceptability and preference indicate that the buildings, despite their sophistication and energy input, did not offer the highest level of thermal comfort. Since this parameter is considered to be mostly influenced by indoor thermal parameters, the following figures present the relationships between the operative temperature and thermal sensation (Figure 11), acceptability ( Figure 12) and preference ( Figure 13) in order to investigate the impact of operative temperature in detail. Here, average votes of thermal sensation, acceptability and preference have been considered for 77 groups of respondents in the considered rooms. Each group consisted of between 5 and 65 people. Based on the test results of a large number of people, it has been found that the relationship between the operative temperature and thermal sensation vote of the respondents is linear. The correlation takes the form of: and is relatively strong for this type of research (R 2 = 0.74). It shows a significant influence of both air and radiant temperatures on thermal comfort. Other parameters, as will be discussed later, have a much lower impact. It is worth noting that Aghniaey et al. [25] has recently proposed a non-linear formula: However, the R 2 value was much lower (0.51). The analysis of the acceptability of indoor conditions reveals that occupants voted overwhelmingly in favour of the thermal environment (over 80% of cases) when the operative the research performed in [25] produced a correlation in the form of: however, only 15 measurement points were considered in [25]. The relationship between the thermal preference of the occupants and the operative however, only 15 measurement points were considered in [25]. The relationship between the thermal preference of the occupants and the operative temperature has been given in Figure 13. A strong linear correlation can be observed, indicating a crucial influence of air and radiant temperatures on this parameter. The linear fitting procedure generated the following equation: Based on the test results of a large number of people, it has been found that the relationship between the operative temperature and thermal sensation vote of the respondents is linear. The correlation takes the form of: and is relatively strong for this type of research (R 2 = 0.74). It shows a significant influence of both air and radiant temperatures on thermal comfort. Other parameters, as will be discussed later, have a much lower impact. It is worth noting that Aghniaey et al. [25] has recently proposed a non-linear formula: However, the R 2 value was much lower (0.51). The analysis of the acceptability of indoor conditions reveals that occupants voted overwhelmingly in favour of the thermal environment (over 80% of cases) when the operative temperature was in the range of 22-26.5 • C. The 90% level of acceptability was generally achieved for 22.5-25.5 • C (Figure 12), albeit with some exceptions.
The obtained fitting curve is characterised by the following formula: the research performed in [25] produced a correlation in the form of: however, only 15 measurement points were considered in [25]. The relationship between the thermal preference of the occupants and the operative temperature has been given in Figure 13. A strong linear correlation can be observed, indicating a crucial influence of air and radiant temperatures on this parameter.
The linear fitting procedure generated the following equation: Energies 2020, 13,1973 14 of 20 whose R 2 was 0.71. In [25] a much lower value of R2 was obtained (0.52) for considerably fewer measurement data points, while the formula took the form of: A study on human thermal perceptions reveal other interesting facts. A relationship between thermal acceptability and thermal sensation votes has been presented in Figure 14. A strong correlation between these two parameters exists.
A study on human thermal perceptions reveal other interesting facts. A relationship between thermal acceptability and thermal sensation votes has been presented in Figure 14. A strong correlation between these two parameters exists. Based on the figure above, it can be concluded that the range of thermal sensation vote of -0.5-0.5, as proposed in the standards [6,8] for buildings category II, might not be the most preferable range. The large experimental data gathered in the project indicate that the respondents in the investigated intelligent buildings were in favour of a warmer environment. The most optimal range of thermal sensation vote proved to be -0.5-1.0.
It is also worth noting that people's preference vote-namely, the will to increase, decrease or maintain the temperature in the room-should be absolutely correlated with their thermal sensation vote. If the occupants consider the indoor environment to be "too hot" (+3) then their thermal preference should be: "much cooler" (-2). Similarly, if they rate the environment to be "too warm" (+2), their preference response should be: "cooler" (-1). If their thermal sensation is fine, they would require "no change" (0). The same situation would occur in the "cold" range of thermal sensation votes. Such a theoretical correlation has been presented in Figure 15 as the blue line. The figure also contains experimental data obtained during the study and their linear fit. Based on the figure above, it can be concluded that the range of thermal sensation vote of −0.5-0.5, as proposed in the standards [6,8] for buildings category II, might not be the most preferable range. The large experimental data gathered in the project indicate that the respondents in the investigated intelligent buildings were in favour of a warmer environment. The most optimal range of thermal sensation vote proved to be −0.5-1.0.
It is also worth noting that people's preference vote-namely, the will to increase, decrease or maintain the temperature in the room-should be absolutely correlated with their thermal sensation vote. If the occupants consider the indoor environment to be "too hot" (+3) then their thermal preference should be: "much cooler" (−2). Similarly, if they rate the environment to be "too warm" (+2), their preference response should be: "cooler" (−1). If their thermal sensation is fine, they would require "no change" (0). The same situation would occur in the "cold" range of thermal sensation votes. Such a theoretical correlation has been presented in Figure 15 as the blue line. The figure also contains experimental data obtained during the study and their linear fit.
As can be seen in the figure both lines are in almost identical alignment, although the research was carried out in different buildings and throughout all the seasons. It proves that the testing procedure was performed correctly and that the proposed methodology of combining physical measurements and a questionnaire survey is very effective. Moreover, it can be concluded that the key element in thermal comfort analysis is the impact of air and radiant temperatures. As can be seen in the figure both lines are in almost identical alignment, although the research was carried out in different buildings and throughout all the seasons. It proves that the testing procedure was performed correctly and that the proposed methodology of combining physical measurements and a questionnaire survey is very effective. Moreover, it can be concluded that the key element in thermal comfort analysis is the impact of air and radiant temperatures.

Thermal Comfort in the Lecture Theater
The largest lecture theater with 200 seats was selected for the analysis. At the time of the test 65 students were present there (39 women and 26 men). During the measurements, the indoor air temperature amounted to 26.8 °C, relative humidity 46.6% and the carbon dioxide concentration 1375 ppm. The occupants indicated their thermal sensation votes during the questionnaire survey. The mean value of TSV (thermal sensation vote) was 0.02. Thus, it can be concluded that the conditions in the room, despite quite a high air temperature, are optimal according to the standards [6,8], namely in the range of -0.5-0.5. Figure 16 presents the distribution of individual TSV values of the occupants.

Thermal Comfort in the Lecture Theater
The largest lecture theater with 200 seats was selected for the analysis. At the time of the test 65 students were present there (39 women and 26 men). During the measurements, the indoor air temperature amounted to 26.8 • C, relative humidity 46.6% and the carbon dioxide concentration 1375 ppm. The occupants indicated their thermal sensation votes during the questionnaire survey. The mean value of TSV (thermal sensation vote) was 0.02. Thus, it can be concluded that the conditions in the room, despite quite a high air temperature, are optimal according to the standards [6,8], namely in the range of −0.5-0.5. Figure 16 presents the distribution of individual TSV values of the occupants. As can be seen in the figure both lines are in almost identical alignment, although the research was carried out in different buildings and throughout all the seasons. It proves that the testing procedure was performed correctly and that the proposed methodology of combining physical measurements and a questionnaire survey is very effective. Moreover, it can be concluded that the key element in thermal comfort analysis is the impact of air and radiant temperatures.

Thermal Comfort in the Lecture Theater
The largest lecture theater with 200 seats was selected for the analysis. At the time of the test 65 students were present there (39 women and 26 men). During the measurements, the indoor air temperature amounted to 26.8 °C, relative humidity 46.6% and the carbon dioxide concentration 1375 ppm. The occupants indicated their thermal sensation votes during the questionnaire survey. The mean value of TSV (thermal sensation vote) was 0.02. Thus, it can be concluded that the conditions in the room, despite quite a high air temperature, are optimal according to the standards [6,8], namely in the range of -0.5-0.5. Figure 16 presents the distribution of individual TSV values of the occupants.  As can be seen the largest number of women (ca. 55%) and men (36%) rated the indoor conditions as very good (a neutral "0"). Generally, almost 85% of occupants expressed positive opinions (from "−1" do "+1") about their thermal sensations, which almost meets the requirements of the standards [6,8] of 90%.
Although, the mean thermal sensation was 0.02 the calculated results according to the standard [6] generated the PMV value of −0.09. The explanation of the discrepancy between the actual and predicted values might be linked with the influence of other parameters, not included in the methodology presented in the standard such as carbon dioxide concentration or BMI (body mass index) of individual respondents. Figure 17 presents the relationship between thermal sensation votes of the students in the lecture room 4.09 of the Energis building and their BMI values for the largest group of 65 people (1a) as well as two other groups, consisting of 60 (2a) and 57 people (3a).
As can be seen the largest number of women (ca. 55%) and men (36%) rated the indoor conditions as very good (a neutral "0"). Generally, almost 85% of occupants expressed positive opinions (from "-1" do "+1") about their thermal sensations, which almost meets the requirements of the standards [6,8] of 90%.
Although, the mean thermal sensation was 0.02 the calculated results according to the standard [6] generated the PMV value of -0.09. The explanation of the discrepancy between the actual and predicted values might be linked with the influence of other parameters, not included in the methodology presented in the standard such as carbon dioxide concentration or BMI (body mass index) of individual respondents. Figure 17 presents the relationship between thermal sensation votes of the students in the lecture room 4.09 of the Energis building and their BMI values for the largest group of 65 people (1a) as well as two other groups, consisting of 60 (2a) and 57 people (3a). 16 18 20  There seems to be a weak dependence of BMI on thermal sensation of the respondents. People of large body mass index would generally consider the environmental conditions as warmer than those of low BMI. However, this issue needs further studies and clarification, especially considering that this problem is hardly ever considered in the literature.

General Sensation Vote
Apart from the thermal environment in the intelligent buildings, other factors such as noise, smell, and light intensity etc. might have an impact on the well-being of the occupants. It should also be considered as part of the study, since the analysed buildings ought to provide the overall positive sensations. Thus, a final question in the survey dealt with a general sensation of a respondent. Here, the volunteers were asked to provide the answer to the question on how they felt at the moment of filling in the questionnaire. The possible answers to choose from were: "very good" (+2), "good" (+1), "neutral" (0), "bad" (-1), "very bad" (-2). Figure 18 presents the distribution of the votes as taken from 1369 questionnaires. There seems to be a weak dependence of BMI on thermal sensation of the respondents. People of large body mass index would generally consider the environmental conditions as warmer than those of low BMI. However, this issue needs further studies and clarification, especially considering that this problem is hardly ever considered in the literature.

General Sensation Vote
Apart from the thermal environment in the intelligent buildings, other factors such as noise, smell, and light intensity etc. might have an impact on the well-being of the occupants. It should also be considered as part of the study, since the analysed buildings ought to provide the overall positive sensations. Thus, a final question in the survey dealt with a general sensation of a respondent. Here, the volunteers were asked to provide the answer to the question on how they felt at the moment of filling in the questionnaire. The possible answers to choose from were: "very good" (+2), "good" (+1), "neutral" (0), "bad" (−1), "very bad" (−2). Figure 18 presents the distribution of the votes as taken from 1369 questionnaires.
The majority of both women and men were either satisfied with the environment ("+1") or had a natural feeling towards it ("0"). Some men and few women felt very good ("+2"). The rest, however, did not share those positive or neutral sensations. The negative feelings were expressed by ca. 18.5% of women and ca. 12% of men. Naturally, it might be related to various factors, other than thermal environment. In order to clarify the relationship between the general sensation and thermal sensation votes, a graph has been constructed ( Figure 19) based on average data from 77 rooms to investigate the interdependence of these two parameters. Energies 2020, 13, x FOR PEER REVIEW 17 of 20 The majority of both women and men were either satisfied with the environment ("+1") or had a natural feeling towards it ("0"). Some men and few women felt very good ("+2"). The rest, however, did not share those positive or neutral sensations. The negative feelings were expressed by ca. 18.5% of women and ca. 12% of men. Naturally, it might be related to various factors, other than thermal environment. In order to clarify the relationship between the general sensation and thermal sensation votes, a graph has been constructed ( Figure 19) based on average data from 77 rooms to investigate the interdependence of these two parameters.  General sensation vote above 0 indicates the positive assessment of the environmental conditions. It occurs mostly in the range of thermal sensation votes from -0.75 to +1.25. It further proves the idea already mentioned in section 3.2. that people tend to like warmer environments. At the same time, the respondents tend to assess the environment as negative (general sensation vote below 0), if the thermal conditions are perceived to be too hot or too cold, albeit with some exceptions. A deviation from this trend might be attributed to the influence of other factors, such as air humidity, carbon dioxide concentration as well as other individual factors such as BMI.  The majority of both women and men were either satisfied with the environment ("+1") or had a natural feeling towards it ("0"). Some men and few women felt very good ("+2"). The rest, however, did not share those positive or neutral sensations. The negative feelings were expressed by ca. 18.5% of women and ca. 12% of men. Naturally, it might be related to various factors, other than thermal environment. In order to clarify the relationship between the general sensation and thermal sensation votes, a graph has been constructed ( Figure 19) based on average data from 77 rooms to investigate the interdependence of these two parameters. General sensation vote above 0 indicates the positive assessment of the environmental conditions. It occurs mostly in the range of thermal sensation votes from -0.75 to +1.25. It further proves the idea already mentioned in section 3.2. that people tend to like warmer environments. At the same time, the respondents tend to assess the environment as negative (general sensation vote below 0), if the thermal conditions are perceived to be too hot or too cold, albeit with some exceptions. A deviation from this trend might be attributed to the influence of other factors, such as air humidity, carbon dioxide concentration as well as other individual factors such as BMI. General sensation vote above 0 indicates the positive assessment of the environmental conditions. It occurs mostly in the range of thermal sensation votes from −0.75 to +1.25. It further proves the idea already mentioned in Section 3.2. that people tend to like warmer environments. At the same time, the respondents tend to assess the environment as negative (general sensation vote below 0), if the thermal conditions are perceived to be too hot or too cold, albeit with some exceptions. A deviation from this trend might be attributed to the influence of other factors, such as air humidity, carbon dioxide concentration as well as other individual factors such as BMI.

Conclusions
The tests performed in two modern intelligent buildings in the space of 1.5 years have generally shown that despite their sophistication and energy input, they did not offer the highest level of thermal comfort as evidenced by the data on thermal sensation, acceptability and preference of the respondents. General sensation vote, which is directly related to the quality of the indoor environment experienced by the occupants, has also proved to reveal that a number of people were unsatisfied.
The measurements of indoor air parameters showed that operative temperature sometimes exceeded the required value, although this might be caused by the occupants themselves and their thermal preferences. A similar situation occurred with relative humidity, whose value fell below 25% during some measurements. Based on the thermal sensation vote it turned out that only 66.3% of women and 76.4% of men felt comfortable throughout the whole study. This is especially important, since thermal environment proved to be the most important element for ensuring the well-being of the occupants, as expressed by the general sensation vote of the occupants.
The obtained data have shown that people are generally in favour of a warmer environment. It might, to some extent, explain the number of people dissatisfied. Thus, the building operators might consider this fact for the settings of the HVAC systems. Actually, the role of the HVAC systems combined with BMS (building management system) is very important in ensuring high quality conditions. Their operation should be monitored constantly, so that comfort conditions are provided to the occupants at all times.
Broadening the experimental database will enable the development of control algorithms for the building management system that will be optimised to provide maximal thermal comfort conditions for building occupants while minimizing the energy consumption of modern and intelligent buildings. Such papers are rare and are usually based on computer simulations only [41], without backing the findings with real life research results. Thus, the future experimental work of the authors might have a scientific, but also a significant practical value.
Supplementary Materials: The following are available online at http://www.mdpi.com/1996-1073/13/8/1973/s1. Table S1: Data on room occupancy during the study in 77 rooms, Table S2: Data on carbon dioxide concentration measurements in 77 rooms, Table S3: Data on thermal sensation, thermal acceptability, thermal preference and general sensation votes in 77 rooms according to 1369 questionnaires.