Improving Fuel Economy of Spark Ignition Engines Applying the Combined Method of Power Regulation

One of the disadvantages of spark ignition engines, whose power is regulated by throttling, is the increased fuel consumption at low loads and when the engine is idle. The combined method of engine power regulation by switching off the cylinder group and throttling working cylinders is one of the effective ways to improve fuel economy in the above-mentioned modes. This article presents the research results of the combined method of engine power regulation which can be realized by minor structural changes in operating conditions. The method implies the following: at low loads and at idle speed of the engine. Fuel supply to the group of cylinders is switched off with the simultaneous increase of the cyclic fuel supply in the working cylinders. The adequacy of the calculated results has been checked by the indication of operating processes in switched off and working cylinders. The research results of a six-cylinder spark ignition engine with the distributed gasoline injection using the combined power regulation system have been shown. The angles of opening the throttle which provides a non-shock transition from the operation with all cylinders to the operation with the cylinder group switched off have been determined.


Introduction
Many factors influence fuel economy (FE) and the amount of pollution (HS) in the exhaust gas (EG) of cars with internal combustion engines (ICE). Research carried out on automobile engines shows that the modes of car motion have great influence on these indicators.
The movement of a car, in large cities in particular, is accompanied by complicated operating modes of the engine: acceleration, deceleration, constant and unstable modes, and modes of independent and One of the most effective methods to improve fuel efficiency in the above-mentioned modes is switching off the group of cylinders with the change of the gas exchange system. This method is widely used in modern engines. In fact, it is the combined method of power regulation as it includes switching off the cylinder group and throttling the working cylinders. The homogeneity of the flammable mixture influences the efficiency of disconnecting the cylinders [33]. This is noticeable especially with direct injection spark engines [34]. This also allows for an ecological effect [35] and the fuel economy effect [36], and the issue of tribological performance of piston compression ring and connecting rod bearing is also addressed [37]. According to Ihlemann at al. this is the technology of the future [38].
The use of this method requires significant changes in the design of the engine and is realized in the production process.
The aim of this work is improving fuel economy of spark ignition engines applying the combined method of power regulation.
The combined method, in which the system of gas exchange does not change, has been studied. The power of the engine at small external loads is obtained by switching off the cylinder group when the second group of cylinders works with a large opening of the throttle and higher efficiency. The group of cylinders is switched off by disabling the fuel supply to these cylinders. The position of the throttle valve and the cyclic supply of fuel in the working cylinders is simultaneously increased. It ensures equal power for the operation with all cylinders and with the cylinder group switched off.

Theoretical Substantiation of Possible Improvement of Fuel Economy
One of the main reasons for the significant deterioration of fuel economy of spark ignition engines in low load and idling modes is a decrease of the indicated efficiency of the engine and an increase of mechanical losses. Under the combined power regulation method, if the indicated efficiency increases and the mechanical losses decrease, as compared to throttle all cylinders, fuel economy of spark ignition engines is improved.
The comparison has been made for a six-cylinder engine with a distributed gasoline injection system and feedback [35,39]. The dependency of the indicated efficiency on the average effective pressure, which is proportional to the external load, has been determined taking into account the nature of the combustion, the duration of the combustion phases, and the effect of residual gas [10,34,40].
The dependencies of the indicated efficiency "η i " on the average effective pressure "p e " from zero to an average effective pressure of 0.35 MPa are shown in Figure 1. It implies throttling and switching off three cylinders at loads where the operation of three and six cylinders is possible [39].
As it can be seen from the shown dependencies, the value of the indicated efficiency when three cylinders are switched off, η i varies from 0.306 (in idling mode) to 0.345 (before the enrichment of the mixture). When throttling, the indicated efficiency η i th at this load varies within the range of 0.26, ..., 0.32. Thus, the transition from throttling fuel-air mixture to the combined method at idling modes and low loads by switching off the cylinder group and throttling working cylinders can increase the indicated efficiency of a gasoline engine with an electronic control and a feedback injection system by 13.7-7.8%. With an average effective pressure of more than 0.325 MPa, it is advisable to throttle all cylinders.
The effect of the combined method of power regulation on mechanical losses has been estimated at the same values of the average effective pressure p e . The average effective pressure pe required for vehicle motion when throttling and switching off "k" cylinders of the engine with "i" cylinders has been determined by the dependencies: where pi th and pid are the average indicated pressure when throttling and switching off the cylinders; pm th and pmd are the average pressure of mechanical losses using the combined method of power regulation. It is known that, during throttling, the average mechanical loss pressure pm th includes the average pressure pt th used for friction, pressure pg th for the gas exchange process, and pressure pd th for the camshaft drive, auxiliary equipment and ventilation losses. That is: When "k" cylinders of an "i"-cylinder engine are switched off, the average mechanical loss pressure pm d includes the average pressure p / t d used for friction in the working "i-k" cylinders and pressure p // t d in "k" switched off cylinders, the loss pressure pg d for gas exchange process in the "i-k" working cylinders and p // g d in "k" switched off cylinders, the pressure pd d for the camshaft drive, auxiliary equipment, and ventilation losses, as well as the average pressure pq d for heat losses in the switched off "k" cylinders is: Components of mechanical losses have been calculated using theoretical and empirical dependencies. Some of them have been partially identified experimentally.
Using these data, the dependence of the engine performance on the average effective pressure has been shown when throttling ( Figure 2) and switching off the three cylinders of the engine ( Figure  3) for n = 1800 rpm. The average effective pressure p e required for vehicle motion when throttling and switching off "k" cylinders of the engine with "i" cylinders has been determined by the dependencies: where p i th and p id are the average indicated pressure when throttling and switching off the cylinders; p m th and p md are the average pressure of mechanical losses using the combined method of power regulation. It is known that, during throttling, the average mechanical loss pressure p m th includes the average pressure p t th used for friction, pressure p g th for the gas exchange process, and pressure p d th for the camshaft drive, auxiliary equipment and ventilation losses. That is: When "k" cylinders of an "i"-cylinder engine are switched off, the average mechanical loss pressure p m d includes the average pressure p / t d used for friction in the working "i-k" cylinders and pressure p // t d in "k" switched off cylinders, the loss pressure p g d for gas exchange process in the "i-k" working cylinders and p // g d in "k" switched off cylinders, the pressure p d d for the camshaft drive, auxiliary equipment, and ventilation losses, as well as the average pressure p q d for heat losses in the switched off "k" cylinders is: Components of mechanical losses have been calculated using theoretical and empirical dependencies. Some of them have been partially identified experimentally.
Using these data, the dependence of the engine performance on the average effective pressure has been shown when throttling ( Figure 2) and switching off the three cylinders of the engine (Figure 3) for n = 1800 rpm.       of power regulation of gasoline engine, fuel economy improvements can be expected as a result of reducing the internal losses.
Using the method of the volume balance, a mathematical model of the engine operating process with cylinders switched off has been developed [23,41,42]. The adequacy of the calculated results has been checked by the indication of operating processes in switched-off and working cylinders.
The mathematical model to evaluate vehicle fuel consumption and pollution emission in a driving cycle using the combined method of power regulation has been developed in scientific papers. Fuel economy modeling is closely linked to vehicle weight, which is increasing by 4.7% annually on cars sold in the Chinese market since 2015 [43], therefore, modeling of exhaust emissions and energy sustainability is performed [44], which is heavily dependent on the interests of energy distribution companies [45]. The assessment of pollutions emissions is related to the promotion of green vehicle use [46], both with an efficient quantified risk assessment [47] resulting from the use of floating vehicle data [48] and on the optimization of control strategy to reduce fuel consumption [49], fuel consumption software (P∆P) [50], interactions between vehicles and pedestrians [51], and vehicle routing problems [52]. Ehsani et al. provides a clear model for the dependence of fuel consumption on carbon dioxide emissions [53]. Applying such a model would reduce freight transport exhaust and improve fuel economy [54]. However, such links are very much dependent on traffic jams if we look at the urban situation [55].
The theoretical analysis shows that the use of the combined power regulation method will improve fuel economy of spark ignition engines compared with throttling in partial load modes and idling modes.

Working out the Fuel Supply System
The experimental model of a fuel supply system to implement the combined power regulation method is based on a Bosch "Motronik ML 4.1" ("Robert Bosch GmbH", Gerlingen, Germany) fuel supply system in the mechanical drive throttle. The scheme of the experimental system is shown in Figure 4 [20]. The main algorithm of its operation implies the termination of the fuel supply to the switched-off cylinders without changing the gas exchange in small loads and idling modes. The engine is equipped with the new system without structural changes in the electronic control unit of the injection system and engine ignition. It can, therefore, be installed on vehicles in operation. This system of power regulation has five patents in the Ukraine for utility models [35].
The system works as follows: an electromagnet (31), whose operation is controlled by the electronic control unit of the nozzles (11), is added to the fuel supply system of the engine with a mechanical cable throttle actuator. The core of the electromagnet is connected to the tension roller (27) through which the control cable passes to the throttle (28).
With partial loads and idling mode running, the electric current of the electromagnet (30) is activated by the command of the electronic control unit (11) to the coil relay switching the electromagnet. When the electromagnet (31) switches on, its core moves the tension roller (27) to a predetermined value ∆l. As a result of it the opening angle of the throttle (17) is changed to a predetermined value according to the engine operation with the cylinders switched off.
At the same time, the electronic control unit of the nozzles (11) receives the signals from the rotational speed sensors (24) and the position of the throttle (16) disables the nozzle assembly (10) by re-directing the electric current to the ballast resistance (9). As a result, the engine does not enter the emergency operating mode.
With an increase in the engine load to a mode where the operation with a subset of cylinders becomes less economical with respect to fuel consumption than with all cylinders, at the same crankshaft rotation frequency, the electronic control unit of the nozzles (11), according to the signal of the position sensor of the throttle valve (16), connects the block of the inactive nozzles (10) to the fuel supply system. At the same time, electromagnet (31) controls the tension roller (27). The angle of opening the throttle (17) changes to the value corresponding to the engine operation with all cylinders.
When reducing the load of the engine or during transition to the idling mode, when the engine is more efficient at switching off the cylinder group, there is a reverse process of disconnecting the block of injectors and the inclusion in the chain of the ballast resistance. The angle of opening the throttle changes simultaneously to the value corresponding to the engine operation for part of cylinders.
The cold start of the engine and its heating occurs due to the engine operation with all cylinders. This is provided by the air temperature sensor (19) and the temperature sensor of the engine (22), the signal of which comes to the electronic control unit of the nozzles (11). The group of switching off cylinders can also be changed.
Energies 2020, 13, x FOR PEER REVIEW 7 of 20 opening the throttle (17) changes to the value corresponding to the engine operation with all cylinders.
When reducing the load of the engine or during transition to the idling mode, when the engine is more efficient at switching off the cylinder group, there is a reverse process of disconnecting the block of injectors and the inclusion in the chain of the ballast resistance. The angle of opening the throttle changes simultaneously to the value corresponding to the engine operation for part of cylinders.

Working out the Experimental Installation
For experimental research, an experimental installation has been developed consisting of a six-cylinder inline Opel C30 LE engine. The technical characteristic, given in Table 1. The engine has been installed on a universal brake stand SGEU-100 with an electric brake AKB-92-4, the power of 100 kW and a maximum rotation 3000 rpm. The installation enables testing the engine in wide limits of external loads. The schematic diagram of the experimental installation with measuring devices is shown in Figure 5.
The experimental prototype of the fuel supply system to implement the combined power regulation method is installed on the engine ( Figure 6).
Separate exhaust pipes for a group of three cylinders that constantly work and a group of switched-off cylinders have been installed on the engine. In the outlet pipeline of a continuously working cylinder group, a three-component catalytic converter manufactured by the Arvin Tefh company (Madison, IN, USA) has been installed on the 1.5 L engine. This is only the working cylinder group.

Working out the Experimental Installation
For experimental research, an experimental installation has been developed consisting of a sixcylinder inline Opel C30 LE engine. The technical characteristic, given in Table 1.
The engine has been installed on a universal brake stand SGEU-100 with an electric brake AKB-92-4, the power of 100 kW and a maximum rotation 3000 rpm. The installation enables testing the engine in wide limits of external loads. The schematic diagram of the experimental installation with measuring devices is shown in Figure 5.
The experimental prototype of the fuel supply system to implement the combined power regulation method is installed on the engine (Figure 6).
Separate exhaust pipes for a group of three cylinders that constantly work and a group of switched-off cylinders have been installed on the engine. In the outlet pipeline of a continuously working cylinder group, a three-component catalytic converter manufactured by the Arvin Tefh company (Madison, Indiana, USA) has been installed on the 1.5 L engine. This is only the working cylinder group.    Measurement equipment accuracy is presented in Table 2.  Measurement equipment accuracy is presented in Table 2.

Results and Discussion
The efficiency of the combined method as for fuel economy improvement has been assessed on the load characteristics in the load area, where the engine can operate with throttling six cylinders or with throttling three cylinders and three cylinders are switched off. Figure 7 shows the load characteristics of the engine for its operation with three and six cylinders at n = 2600 rpm. Hence, it is evident that throughout all loads from idling modes and before the operation of the enrichment device, the stoichiometric composition of the fuel and air mixture is maintained, regardless of the number of working cylinders (λ = 1.0). When three cylinders are switched off in this high-speed mode, the maximum torque of the engine M t decreases from 191 Nm to 84 Nm. For loads up to 65 Nm for three-cylinder engine performance there is an improvement in fuel economy compared to the operation with all cylinders, hourly G f and brake specific fuel consumption (BSFC) is reduced by an average of 13%. At the same time, load reduction fuel economy improves. In idling modes for fuelling a three-cylinder engine, the fuel economy is about 19%. When the load M t = 65 Nm, fuel consumption for the engine running on six and three cylinders is the same. At a larger load the engine operation with a group of switched off cylinders becomes less economical and therefore inappropriate. The operation of the engine with three cylinders compared to the operation with six cylinders is characterized by a larger opening of the throttle φ dr , the lower thinning of ∆p k , and larger volumetric efficiency of engine η v , with practically the same air flow G air . When determining the load characteristics, the concentration of pollutions in exhaust gases of the engine has been measured before and after the converter. The obtained characteristics are shown in Figure 8.
An analysis of the environmental performance of the engine indicates a significant increase in nitrogen oxide NOx concentration when the engine runs on three cylinders compared with the engine running on six cylinders. When applying a three-component catalytic converter, the NOx concentration in both cases is significantly reduced to practically the same level. Similar results were  When determining the load characteristics, the concentration of pollutions in exhaust gases of the engine has been measured before and after the converter. The obtained characteristics are shown in Figure 8.
An analysis of the environmental performance of the engine indicates a significant increase in nitrogen oxide NO x concentration when the engine runs on three cylinders compared with the engine running on six cylinders. When applying a three-component catalytic converter, the NO x concentration in both cases is significantly reduced to practically the same level. Similar results were obtained by Ozhan et al. after years of research using multilevel flow modeling [56]. Concentrations of carbon oxide CO, carbon dioxide CO 2 , and hydrocarbons HC in the operation of the engine with catalytic converters with different numbers of working cylinders are also practically the same. The improvement in fuel economy for the operation with three cylinders has been obtained in other high-speed modes ( Figure 9); the engine load was low (Mt = 40 Nm).
One of the main issues when adjusting the power of a gasoline engine by the combined method is to determine the rules of changing the position of the throttle valve when switching off and switching on the cylinder group. It provides a non-shock process of changing the number of working The improvement in fuel economy for the operation with three cylinders has been obtained in other high-speed modes ( Figure 9); the engine load was low (M t = 40 Nm).
One of the main issues when adjusting the power of a gasoline engine by the combined method is to determine the rules of changing the position of the throttle valve when switching off and switching on the cylinder group. It provides a non-shock process of changing the number of working cylinders. To establish such a pattern, an experimentally determined series of load characteristics with the measurement of the engine torque, fuel consumption, and the position of the throttle valve for each speed mode, a load mode has been established. The results obtained are similar to those of Fleischman et al. bus tests, where the test was conducted under roadworthiness test conditions [57]. When it is exceeded, the operation of the engine with the switched-off cylinders is inappropriate in terms of fuel economy.  The dependencies show that when the group of cylinders is switched off and on, the position of the throttle valve does not change, and the torque will vary several times.
As can be seen from the characteristics shown, the same torque when switching off and on a group of cylinders can be obtained at different ratios of the opening angle of the throttle valve.
The analysis of experimentally determined characteristics ( Figure 11) shows that for the engine in all high-speed modes to obtain a practically unbreakable transition from the operation with three cylinders to the operation with six cylinders, and vice versa, it is advisable to do the transition at a torque moment Mt close to 50 Nm and a ratio of the opening angle of the throttle valve of 1.75.  Figure 10 shows the experimental dependencies of the hourly flow of petrol G p and the opening angle of the throttle valve φ dr on the torque M t of a six-cylinder Opel C30 LE petrol engine with a distributed injection system with a feedback with six and three cylinders at different speeds.
The dependencies show that when the group of cylinders is switched off and on, the position of the throttle valve does not change, and the torque will vary several times.
As can be seen from the characteristics shown, the same torque when switching off and on a group of cylinders can be obtained at different ratios of the opening angle of the throttle valve. The analysis of experimentally determined characteristics ( Figure 11) shows that for the engine in all high-speed modes to obtain a practically unbreakable transition from the operation with three cylinders to the operation with six cylinders, and vice versa, it is advisable to do the transition at a torque moment M t close to 50 Nm and a ratio of the opening angle of the throttle valve of 1.75. n=1200 rpm 6c n=1200 rpm 3c n=1800 rpm 6c n=1800 rpm 3c n=2400 rpm 6c n=2400 rpm 3c n=3000 rpm 6c n=3000 rpm 3c n=3600 rpm 6c n=3600 rpm 3c One of the main factors influencing the efficiency of the combined method for power regulation of a multi-cylinder petrol engine is the duration of switching off and on the cylinder group.
The exact duration values of the transition process when switching off and on the cylinder group have been determined by indicating the operating process in the cylinder. Figure 11 shows a fragment of oscillograms of the operating process in cylinder A, when fuel is supplied to the cylinder; B, when fuel is not supplied to the cylinder. Oscillograms have been recorded at a load of Mt = 50 Nm, (n = 2000 rpm).
From these fragments it can be seen that both switching on and switching off the cylinder have a transition process in 1-2 operating cycles and almost without gradual increase or decrease of the indicated pressure. When the cylinders are switched on ( Figure 11A), the full operating cycle has been restored for approximately 0.15 s. At the same time, the maximum combustion pressure, starting from the second cycle, remains unchanged during all subsequent cycles within the uneven values of cylinder operation.
A similar process occurs with switching off the cylinders ( Figure 11B). After the fuel injector stops working, the first operating cycle is without breaking the parameters of the operating process. The next one is without the combustion process. The duration of the transition process when switching off the cylinders lasts for about 0.1 s.
To prove a short-term nature of the transition process, when cylinders are turned on and off, the oscillograms of the operating process during acceleration and deceleration of the engine (Figure 12) at loads have been recorded in unstable modes. The brake stand has created loads according to its speed characteristics ( Figure 13).
Additionally, Figure 12 shows the oscillograms of the throttle position change φdr, the dilution in the inlet line Δpk, the operation of the fuel nozzle, the moment of the TDP, and the moment of a spark jump. One of the main factors influencing the efficiency of the combined method for power regulation of a multi-cylinder petrol engine is the duration of switching off and on the cylinder group.
The exact duration values of the transition process when switching off and on the cylinder group have been determined by indicating the operating process in the cylinder. Figure 11 shows a fragment of oscillograms of the operating process in cylinder A, when fuel is supplied to the cylinder; B, when fuel is not supplied to the cylinder. Oscillograms have been recorded at a load of M t = 50 Nm, (n = 2000 rpm).
From these fragments it can be seen that both switching on and switching off the cylinder have a transition process in 1-2 operating cycles and almost without gradual increase or decrease of the indicated pressure. When the cylinders are switched on ( Figure 11A), the full operating cycle has been restored for approximately 0.15 s. At the same time, the maximum combustion pressure, starting from the second cycle, remains unchanged during all subsequent cycles within the uneven values of cylinder operation.
A similar process occurs with switching off the cylinders ( Figure 11B). After the fuel injector stops working, the first operating cycle is without breaking the parameters of the operating process. The next one is without the combustion process. The duration of the transition process when switching off the cylinders lasts for about 0.1 s.
To prove a short-term nature of the transition process, when cylinders are turned on and off, the oscillograms of the operating process during acceleration and deceleration of the engine (Figure 12) at loads have been recorded in unstable modes. The brake stand has created loads according to its speed characteristics ( Figure 13).
Additionally, Figure 12 shows the oscillograms of the throttle position change φ dr , the dilution in the inlet line ∆p k , the operation of the fuel nozzle, the moment of the TDP, and the moment of a spark jump.
With the gradual opening of the throttle, the rotational speed "n", the maximum pressure in the switched off cylinder "p" and, therefore, the load on the engine increase. At the throttle angle the cylinders are switched off. When the angle is larger, the engine operation with the cylinder part becomes inefficient. At the same time, the angle of opening the throttle is reduced to avoid a spin-like torque change. This causes an increase in the dilution in the inlet pipeline ∆p k , which results in a decrease of the maximum pressure "p" in the next cycle after the cylinders are switched on. In this cycle, the combustion process still does not occur. In subsequent cycles the combustion process is restored and the maximum pressure increases as a result of further opening of the throttle. With the gradual opening of the throttle, the rotational speed "n", the maximum pressure in the switched off cylinder "p" and, therefore, the load on the engine increase. At the throttle angle the cylinders are switched off. When the angle is larger, the engine operation with the cylinder part becomes inefficient. At the same time, the angle of opening the throttle is reduced to avoid a spinlike torque change. This causes an increase in the dilution in the inlet pipeline Δpk, which results in a decrease of the maximum pressure "p" in the next cycle after the cylinders are switched on. In this cycle, the combustion process still does not occur. In subsequent cycles the combustion process is restored and the maximum pressure increases as a result of further opening of the throttle.    When the throttle valve closes, a reverse process occurs. In the process of switching the opening angle of the throttle valve φdr sharply decreases. There is a decrease of the dilution in the inlet line. In the next cycle after the cylinders are switched off, the combustion characterized by low pressure in the cylinder does not occur. In the first cycle after the cylinders are switched off, the maximum pressure becomes even lower than in subsequent cycles. It is due to the fact that the pressure reduction wave from the throttle valve has not yet been able to reach the switched off cylinders.
Such a short-term transition process is facilitated by the instantaneous reduction of the dilution when the position of the throttle valve is changed. Due to this all fuel residues from the inlet valve are absorbed into the cylinder.
With further closure of the throttle valve, the dilution increase and the maximum cylinder pressure gradually decreases as a result of volumetric efficiency of engine reduction. The oscillograms recorded with different acceleration and deceleration rates show similar processes of switching the cylinders on and off.   When the throttle valve closes, a reverse process occurs. In the process of switching the opening angle of the throttle valve φdr sharply decreases. There is a decrease of the dilution in the inlet line. In the next cycle after the cylinders are switched off, the combustion characterized by low pressure in the cylinder does not occur. In the first cycle after the cylinders are switched off, the maximum pressure becomes even lower than in subsequent cycles. It is due to the fact that the pressure reduction wave from the throttle valve has not yet been able to reach the switched off cylinders.
Such a short-term transition process is facilitated by the instantaneous reduction of the dilution when the position of the throttle valve is changed. Due to this all fuel residues from the inlet valve are absorbed into the cylinder.
With further closure of the throttle valve, the dilution increase and the maximum cylinder pressure gradually decreases as a result of volumetric efficiency of engine reduction. The oscillograms recorded with different acceleration and deceleration rates show similar processes of switching the cylinders on and off. When the throttle valve closes, a reverse process occurs. In the process of switching the opening angle of the throttle valve φ dr sharply decreases. There is a decrease of the dilution in the inlet line. In the next cycle after the cylinders are switched off, the combustion characterized by low pressure in the cylinder does not occur. In the first cycle after the cylinders are switched off, the maximum pressure becomes even lower than in subsequent cycles. It is due to the fact that the pressure reduction wave from the throttle valve has not yet been able to reach the switched off cylinders.
Such a short-term transition process is facilitated by the instantaneous reduction of the dilution when the position of the throttle valve is changed. Due to this all fuel residues from the inlet valve are absorbed into the cylinder.
With further closure of the throttle valve, the dilution increase and the maximum cylinder pressure gradually decreases as a result of volumetric efficiency of engine reduction. The oscillograms recorded with different acceleration and deceleration rates show similar processes of switching the cylinders on and off. The oscillograms of transition processes recorded in various modes of the engine show that the duration of the transition processes when the cylinder is switched off and on the petrol injection is insignificant and is within 1-2 operating cycles. It enables to increase the speed of the transition process, to improve the engine power regulation. It is one of the reasons to improve fuel economy when applying the combined method of power regulation for a multi-cylinder petrol engine.

Conclusions
Experimental studies of a six-cylinder engine have shown that when using the combined method of power regulation. The engine runs steady in all load and high-speed modes. The experimentally established fuel economy at the idling mode is about 19%, and the average economy of loading modes is about 13%.
The application of the combined power regulation method almost does not affect the environmental performance of the engine with a three-component catalytic converter installed in the production system.
The shock-free process of switching off and on a group of cylinders may provide a change in the position of the throttle in these processes with a certain ratio. In this case, the cyclic supply of gasoline also varies with the corresponding value. The composition of fuel and air mixture does not change.
For the Opel C30 LE engine in all high-speed modes to obtain an almost unbreakable transition from the operation with three cylinders to the operation with six cylinders and vice versa, it is advisable to do the transition at a torque close to 50 Nm and the ratio of the throttle opening angle at 1.75.
It has been established that the duration of switching on and switching off the cylinder group does not exceed 1-2 operating cycles. It cannot significantly affect fuel economy.