Energy and Exergy Analysis of a Flat-Plate Solar Air Heater Artiﬁcially Roughened and Coated with a Novel Solar Selective Coating

: Enhancements in heat transfer, and consequently the thermohydraulic performance of solar air heaters (SAHs), are necessary to widen and optimize their use in many applications such as solar drying or heating buildings. In this investigation, two techniques were used. A novel solar selective coating combined with broken arc ribs roughness was employed with a SAH and the evaluation of the energetic and exergetic performance was applied under four airflow working conditions compared to a smooth absorber SAH coated with the same coating. The results revealed that the Nusselt number of roughened SAH with the new coating exhibited a notable improvement compared to a smooth absorber SAH and a roughened SAH without a coating. Furthermore, the thermal efficiency increased with the increase in the air flow rate and the maximum rise was 18.8% compared to a smooth SAH. The highest increase in exergy was 51.6% with minimum values of exergy destruction and improvement potentials. In brief, the roughened SAH with 4% CNTs / CuO-black paint under the airflow rate of 0.0244 m 3 / s (condition C) exhibited the best energetic and exergetic performance.


Introduction
Solar air collectors (SAHs) are the main component of solar energy utilization systems that absorb incoming solar radiation, transforming it into thermal energy and conveying the energy to the collector's fluid [1]. Despite the huge range of applications of SAHs such as building heating, solar dryers, and water desalination as a consequence of their simple construction, low cost, and ease to build and maintain [2], their thermal efficiency is low especially of flat-plate SAHs because of the low convective heat transfer coefficient between the air and the absorber sheet [3]; in addition, the heat losses to the surrounding environment massively rise with an increase in the absorber plate temperature, specifically under lower airflow rates that cause a lower thermal efficiency [4].
As a result of the intrinsic drawback of SAHs, which is weak thermal efficiency, the use of expanded heat transfer elements like porous and corrugated surfaces as well as finned absorbers, is a necessary solution [5]. Furthermore, other techniques have been proposed to improve the heat transfer coefficient such as different shaped baffles [6], chemical surface treatments [7], reorganizing the flow directions [8], and impinging air jets [9]. Solar selective coatings are recommended to be deposited on the surface of the SAH's absorber for their ability to enhance the SAH's performance [10]. Absorber spectral selectivity is identified  (2) Then, the spectral selectivity was calculated by the following: As suggested by International Energy Agency (IEA) Task 27 report on solar heating and cooling [24]. The optical and morphological characterization of the new coatings have been discussed in detail in our previous study [11]. Briefly, the results showed that 4% CNTs/CuO-black paint was the best composite with solar absorptance and thermal emittance reaching 0.964 and 0.124, respectively, with the highest solar selectivity as illustrated in Figure 1.
Then, the spectral selectivity was calculated by the following: spectral selectivity 0.5?
As suggested by International Energy Agency (IEA) Task 27 report on solar heating and cooling [24]. The optical and morphological characterization of the new coatings have been discussed in detail in our previous study [11]. Briefly, the results showed that 4% CNTs/CuO-black paint was the best composite with solar absorptance and thermal emittance reaching 0.964 and 0.124, respectively, with the highest solar selectivity as illustrated in Figure 1.

The Solar Air Heaters (SAHs) Installation
At the factory at the engineering college (Huazhong Agricultural Uni., Wuhan, China), two units of SAHs were built with a duct volume 0.2 m 3 (2 × 1 × 0.1 m length, width, height, respectively). Double glass covers (thickness of 4 mm and a 20 mm gap in between) were used. Furthermore, the SAHs' bottom (0.08 m thickness) and sides (0.06 m thickness) were insulated with polyurethane slabs (heat conductivity ≤0.025 W/m K).
Aluminum plates (2 mm thick) were used as absorbers, then Al ribs were used to make artificial roughness for one SAH and the other one was left with a smooth absorber. Table 1 shows the roughness geometry parameters employed in the experiment following the recommendation of Hans et al. [15] by employing broken arc ribs of Al on the surface of one absorber. The roughened and smooth absorber sheets were painted with CCu-BP using a spray method for both. A centrifugal fan from the lower side of the collector pushed the ambient air. Fully south-oriented solar air heaters were inclined 30° to the horizontal plane to maximize the incident solar radiation in the daytime, as shown in Figure 2.

The Solar Air Heaters (SAHs) Installation
At the factory at the engineering college (Huazhong Agricultural Uni., Wuhan, China), two units of SAHs were built with a duct volume 0.2 m 3 (2 × 1 × 0.1 m length, width, height, respectively). Double glass covers (thickness of 4 mm and a 20 mm gap in between) were used. Furthermore, the SAHs' bottom (0.08 m thickness) and sides (0.06 m thickness) were insulated with polyurethane slabs (heat conductivity ≤0.025 W/m K).
Aluminum plates (2 mm thick) were used as absorbers, then Al ribs were used to make artificial roughness for one SAH and the other one was left with a smooth absorber. Table 1 shows the roughness geometry parameters employed in the experiment following the recommendation of Hans et al. [15] by employing broken arc ribs of Al on the surface of one absorber. The roughened and smooth absorber sheets were painted with CCu-BP using a spray method for both. A centrifugal fan from the lower side of the collector pushed the ambient air. Fully south-oriented solar air heaters were inclined 30 • to the horizontal plane to maximize the incident solar radiation in the daytime, as shown in Figure 2.

Performance Analysis of the Flat Plate Solar Air Heaters
For the evaluation of RSAH and SSAH energetic and exegetic performances, many variables have been measured. Since the SAHs were fixed and oriented to face the south and inclined with 30° to the horizon. Next, k-type thermocouples connected to a datalogger recorded the absorber, fluid, and glass cover temperatures every three minutes. In addition, the ambient temperature and wind velocity were recorded by a weather station. At the top of the SAH, a pyranometer was fixed to measure the global solar radiation. To circulate the air across the SAHs, a centrifugal fan (TB125, 380 V, 60 Hz, 33-39 m 3 /min) was used and a digital anemometer (AS8556) was used to measure its discharges.

Energetic and Exergetic Performance
Energy analysis is an essential tool to understand the basic design and performance of any thermal system. The first thermodynamic energy balance law was determined by applying the measured measurements from the experiment, the thermal energy balance:

Performance Analysis of the Flat Plate Solar Air Heaters
For the evaluation of RSAH and SSAH energetic and exegetic performances, many variables have been measured. Since the SAHs were fixed and oriented to face the south and inclined with 30 • to the horizon. Next, k-type thermocouples connected to a datalogger recorded the absorber, fluid, and glass cover temperatures every three minutes. In addition, the ambient temperature and wind velocity were recorded by a weather station. At the top of the SAH, a pyranometer was fixed to measure the global solar radiation. To circulate the air across the SAHs, a centrifugal fan (TB125, 380 V, 60 Hz, 33-39 m 3 /min) was used and a digital anemometer (AS8556) was used to measure its discharges.

Energetic and Exergetic Performance
Energy analysis is an essential tool to understand the basic design and performance of any thermal system. The first thermodynamic energy balance law was determined by applying the measured measurements from the experiment, the thermal energy balance: where Q A , Q u , and Q los are the absorbed, useful, and lost energy, respectively. Based on Duffie and Beckman [25], the useful heat gain from the collector is: The radiation absorbed by the absorber surface is described as: The F R that implies the quantity that relates a collector's actual useful energy gain to the useful gain if the entire collector's surface was at the temperature of the fluid inlet.
The collector's overall loss coefficient U los is the sum of the top, lower, and edges loss coefficients: Top losses for the numerous covers: Klein [26] produced an empirical equation for U t that is beneficial for assessing both hand and computer calculations: Loss of energy through the collector's bottom is where k is the thermal conductivity and L is the insulation thickness.
The losses within the edge should be referenced to the collector area. If the edge loss coefficient-area product is the (U/A) edge, then the edge loss coefficient, with regard to the collector area A c , is The thermal efficiency of the SAH according to ASHRAE is: The heat transfer coefficient (h) for the absorber is [15]: where the heat transfer coefficient was used to determine the Nusselt number (Nu) by using the following equation [27]: The exergy efficiency can be written based on the Second Law of Thermodynamics as the ratio of the absorbed exergy of air divided by the exergy of solar radiation on the collector [28,29]:

Ex in
. Ex in (14) The parameters of this equation are represented as [30,31]: .
The E xu,p actual exergy delivered, considering pressure drop of collector fluid, is calculated by [30]: where η f an is the fan motor efficiency taken equal to 0.9 [30]. The input exergy (the exergy of sun radiation) is defined as: where T a and T sun represent the temperatures of ambient and solar intensity. For the solar intensity temperature, 5600 K was assumed. Van Gool [32] indicated that the optimum exergy efficiency gains for a system or process were naturally achieved by reducing exergy destruction . Ex dest. . When evaluating different economic processes or industries, it is useful to use the idea of an "improvement opportunity" [5,29]. The improvement potential (IP) of a system or process is given by

Uncertainty Analysis
The associated independent variables quantified the relative uncertainty of thermal efficiency, and the uncertainty of thermal efficiency was obtained through the strategy of error propagation. The uncertainty in the estimation of different parameters was evaluated based on the uncertainty of all the associated independent variables in the measurement. If result R is a function of independent variables x 1 , x 2 , x 3 , . . . , x n such that [33,34]: Then, the relative uncertainty [28,31] is The uncertainties of mass flow rate . m was measured by a digital anemometer (AS8556) (air velocity from 0-45 m/s and accuracy ±2.5% ± 0.1), the inlet and outlet temperatures T f ,in and T f ,out were measured by the K-type (measuring ranges −50 to 300 • C and accuracy ±0.1 • C, and solar radiation intensity G T were measured by a pyranometer (measuring range 0 to 2500 W/m 2 and accuracy ≤±5%). A c , C p , and ρ can be considered as the exact value in Equation (23). Thus, the maximum relative uncertainty for thermal efficiency is 5.59%. ( w η η ) is calculated as:

Results and Discussion
In this study, the performance of a solar air heater with broken arc ribs coated with a new solar selective coating compared to a smooth SAH was evaluated. The SAHs were tested under clear sky conditions for several days in October and November (2018) since each airflow rate was conducted for three different days, and one sunny day was selected to represent each airflow rate. Under the climatic conditions of Wuhan, China (latitude: N30.58, longitude: E114.26), a number of experiments were performed in different modes as shown in Table 2.  Figure 3 illustrates the solar radiation (W/m 2 ) and ambient temperature ( • C) through experiments since each experiment started from 9:00 am to 15:36 pm and the data were recorded every three minutes. For solar radiation, which was considered as the most important parameter in the experiment, for all days, the solar radiation curves followed a parabolic shape where the peak occurred at noontime. Despite the changeable and cloudy climate of Wuhan city, almost all clear days were selected to represent the experiment. The maximum value that was reached was 922 W/m 2 on 29 October, but the averages of the solar radiation for all days were 767.8, 754.8, 729.2, and 762.1 W/m 2 on 28 October, 29 October, 31 October, and 9 November, respectively. The performance of the SAHs was highly influenced by the environment, which involves many parameters like wind velocity and ambient temperature, etc. As plotted in Figure 3, the ambient temperatures on the 28, 29, and 31 October were congruent, except that the ambient temperature on 9 November was lower than that of the other days. The ambient temperatures ranged from 26.7 to 32.9 with an average of 28. Similar to the solar radiation curve pattern, the air outlet and the inlet temperature difference T f ,out − T f ,in ( • C) follow a parabolic shape since Figure 4 obviously shows (outlet-inlet) temperatures ( • C) of roughened and smooth SAHs with CCu-BP versus daytime. The difference between the SAH outlet and inlet temperatures for either the roughened or smooth SAH reached a peak in the period from 12:00 to 13:00 because the solar radiation was also at its peak during this period. It is clear that the relationship between the temperature differences and airflow rates is inversely related where the highest differences occurred in case A and ranged from 23.9 to 56.3 with an average value of 47 • C and from 22.3 to 57.3 with an average of 47.6 • C for smooth and roughened SAHs, respectively. The lowest differences were obtained in case D and ranged from 6.   (°C) of roughened and smooth SAHs with CCu-BP versus daytime. The difference between the SAH outlet and inlet temperatures for either the roughened or smooth SAH reached a peak in the period from 12:00 to 13:00 because the solar radiation was also at its peak during this period. It is clear that the relationship between the temperature differences and airflow rates is inversely related where the highest differences occurred in case A and ranged from 23.9 to 56.3 with an average value of 47 °C and from 22.3 to 57.3 with an average of 47.6 °C for smooth and roughened SAHs, respectively. The lowest differences were obtained in case D and ranged from 6. It can be inferred that under stable solar radiation, the new coating with a broken arc roughness could raise the difference between the outlet and inlet temperatures of the air across the SAH compared to the smooth duct due to the increase in the heat transfer coefficient due to the turbulence effect of the employed roughness. Furthermore, the RHAS's    Similar to the solar radiation curve pattern, the air outlet and the inlet temperature difference , , f out f in T T − (°C) follow a parabolic shape since Figure 4 obviously shows (outlet-inlet) temperatures (°C) of roughened and smooth SAHs with CCu-BP versus daytime. The difference between the SAH outlet and inlet temperatures for either the roughened or smooth SAH reached a peak in the period from 12:00 to 13:00 because the solar radiation was also at its peak during this period. It is clear that the relationship between the temperature differences and airflow rates is inversely related where the highest differences occurred in case A and ranged from 23.9 to 56.3 with an average value of 47 °C and from 22.3 to 57.3 with an average of 47.6 °C for smooth and roughened SAHs, respectively. The lowest differences were obtained in case D and ranged from 6. It can be inferred that under stable solar radiation, the new coating with a broken arc roughness could raise the difference between the outlet and inlet temperatures of the air across the SAH compared to the smooth duct due to the increase in the heat transfer coefficient due to the turbulence effect of the employed roughness. Furthermore, the RHAS's   It can be inferred that under stable solar radiation, the new coating with a broken arc roughness could raise the difference between the outlet and inlet temperatures of the air across the SAH compared to the smooth duct due to the increase in the heat transfer coefficient due to the turbulence effect of the employed roughness. Furthermore, the RHAS's T f ,out − T f ,in was higher than that of the SSAH by 1.3, 8, 19.8, and 3.3% for the A, B, C, and D airflow conditions, respectively.

Useful Energy (W), Thermal Efficiency (%,) and Nusselt Number Variation Under Different Working Conditions
The thermal efficiency of the RSAH and SSAH with CCu-BP was investigated under four airflow rates for several days, then one sunny day was selected to represent each airflow rate due to the unstable weather of Wuhan city. Figures 5 and 6 demonstrate the useful energy (W), which is calculated by Equation (5) and thermal efficiency (%), which is computed by Equation (11), respectively, under the same working conditions for both the RSAH and SSAH coated with CCu-BP. As seen in Figure 5, RSAH showed a remarkable rise in useful energy compared to the SSAH for all airflow conditions due to the high-temperature differences T f ,out − T f ,in across the RSAH duct with respect to those across the SSAH duct. The useful energy averages were 405. 18    Consequently, the instantaneous thermal efficiency of RSAH and SSAH had the same tendency of useful energy gained by the used fluid. RSAH clearly showed a higher instantaneous thermal efficiency (%) compared to the SSAHs as seen in Figure 6. The instantaneous thermal efficiency for each airflow condition ranged as follows: • It was noticeable that either the useful energy or thermal efficiency was lower for the RSAH than for the SSAH at the beginning of the experiments, and this decline was increased by the decrease in the ambient temperature as in condition D, which is because the cooled material of the Al ribs has a high heat capacity (921 J/Kg.k), so needs more energy to heat up compared to absorber without Al ribs then some of the absorbed solar radiation is lost for that purpose, which decreases the useful energy and consequently the thermal efficiency. The inverse effect occurred at the end of the experiment since the stored energy in the material of the ribs recovered to the working air and led to a higher useful energy and then a higher thermal efficiency. For more illustration, Figure 7 shows the variation in the temperature parameters ∆T/G T with thermal efficiencies of SSAH and RSAH at the mass flow rates of A, B, C, and D. Furthermore, the empirical relations and regression coefficients between them are tubulated in Table 3. The comparison of the averaged thermal efficiencies of RSAH under airflow condition C for several days is tabulated in Table 4. As illustrated in Equations (5)-(11), thermal efficiency is a function of many parameters such as solar radiation, working fluid temperature differences, heat removal factor, and overall losses coefficient. Consequently, thermal efficiency is massively affected by any variation of those variables. As seen in Table 4, despite operating the RSAH under the same  It can be concluded that the new coating with broken arc roughness enhanced the heat transfer coefficient between the absorber plate and working fluid (air), leading to a noteworthy improvement in useful energy (W). In addition, for both useful energy and thermal efficiency, there was a positive correlation with the increase in airflow rates. Besides, the thermal efficiency of RSAH under working conditions A, B, C, and D increased by 0.8, 7.4, 18.4, and 1.9%, respectively.
The comparison of the averaged thermal efficiencies of RSAH under airflow condition C for several days is tabulated in Table 4. As illustrated in Equations (5)- (11), thermal efficiency is a function of many parameters such as solar radiation, working fluid temperature differences, heat removal factor, and overall losses coefficient. Consequently, thermal efficiency is massively affected by any variation of those variables. As seen in Table 4, despite operating the RSAH under the same airflow, the averaged thermal efficiency varied because of the different amount of incident averaged solar radiation for each day and this clearly appeared on the 24 November, which showed the lowest averaged solar radiation and the lowest thermal efficiency. To calculate the lost energy, estimating the overall heat transfer coefficient(W/m 2 . • C) is necessary and many parameters could affect the overall heat transfer coefficient (W/m 2 . • C) since there is a direct relationship between U los. and (T p -T a ). The more (T p -T a ) occurred, the more lost energy there was. The same manner was used for wind velocity, consequently the wind-heat transfer coefficient. (W/m 2 . • C) as mentioned in [35,36]. Despite 11 October being the day with the highest incident solar radiation, the thermal efficiency was lower than on 31 October since on 11 October, the (T p -T a ) was the highest; also, the wind heat transfer coefficient that dramatically increased the amount of lost energy by radiation and convection consequently decreased the thermal efficiency. The influence of operating and the new coating with roughness parameters on the Nusselt number and heat transfer coefficient for broken arc rib roughened duct and smooth duct are discussed in the following part.
The variation of the heat transfer coefficient (W/m 2 . • C) and Nusselt number with the four working conditions are plotted in Figure 8 for the roughened and smooth SAHs. As predicted with the increase in the air flow rate (Reynolds number), heat transfer coefficient (W/m 2 . • C), and Nusselt number increases for the RSAH since an improvement in turbulent strength takes place. This might be due to the role of artificial roughness, in addition to the more volumetric airflow rates, and the greater rise in the turbulent dissipation rate aside from the turbulent kinetic energy in the flow that brings an important development in wall heat transfer rates.
To conclude, the RSAH with CCu-BP showed a higher heat transfer coefficient (W/m 2 • C), consequently, the Nusselt number was compared to the SSAH with CCu-BP for each working volumetric airflow rate.
Energies 2020, 13, 997 13 of 17 number increases for the RSAH since an improvement in turbulent strength takes place. This might be due to the role of artificial roughness, in addition to the more volumetric airflow rates, and the greater rise in the turbulent dissipation rate aside from the turbulent kinetic energy in the flow that brings an important development in wall heat transfer rates.
To conclude, the RSAH with CCu-BP showed a higher heat transfer coefficient (W/m 2 °C), consequently, the Nusselt number was compared to the SSAH with CCu-BP for each working volumetric airflow rate.

Exergy Efficiency (%) and Improvement Potentials (W) for RSAH and SSAH with the New Coating
For both the RSAH and SSAH coated with CCu-BP, the second law efficiency (exergy efficiency) under different volumetric airflow rates was computed. The results are plotted in Figure 9, and the averages are tabulated in Table 5. Furthermore, the averages of exergy input (W), exergy destruction (W), and improvement potentials (W) in Equations (14)- (20) were used. It is obvious, as plotted in Figure 9, that the exergy efficiency followed the change of instantaneous output or absorbed exergy (W) within the first hour of the experiment for all working conditions; the exergy efficiency and absorbed exergy showed approximate values, and reached its peak during the period of 12:30-13:30 with a big variation between RSAH and SSAH for the benefit of RSAH because at this time, the solar radiation was in peak and RSAH could maintain a higher difference between the air outlet and inlet than the SSAH. The RSAH with CCu-BP increased the exergy efficiency by 5.9, 20, 51.6, and 29.8% for conditions A, B, C, and D, respectively, compared to SSAH with the same coating.

Exergy Efficiency (%) and Improvement Potentials (W) for RSAH and SSAH with the New Coating
For both the RSAH and SSAH coated with CCu-BP, the second law efficiency (exergy efficiency) under different volumetric airflow rates was computed. The results are plotted in Figure 9, and the averages are tabulated in Table 5. Furthermore, the averages of exergy input (W), exergy destruction (W), and improvement potentials (W) in Equations (14)- (20) were used. It is obvious, as plotted in Figure 9, that the exergy efficiency followed the change of instantaneous output or absorbed exergy (W) within the first hour of the experiment for all working conditions; the exergy efficiency and absorbed exergy showed approximate values, and reached its peak during the period of 12:30-13:30 with a big variation between RSAH and SSAH for the benefit of RSAH because at this time, the solar radiation was in peak and RSAH could maintain a higher difference between the air outlet and inlet than the SSAH. The RSAH with CCu-BP increased the exergy efficiency by 5.9, 20, 51.6, and 29.8% for conditions A, B, C, and D, respectively, compared to SSAH with the same coating.
The irreversibility of both RSAH and SSAH and their "improvement potentials" were estimated and the results revealed in Table 5, where there is a reciprocal relationship between exergy destruction and exergy efficiency as well as a temperature difference since the exergy loss is minimal when the thermal efficiency is optimum. The RSAH showed lower energy destruction and improvement potentials compared to SSAH. Furthermore, for the RSAH, the airflow rate in case D was the highest in energy destruction and improvement potentials compared to cases A, B, and C because of the high-pressure drop across the duct. In contrast, the RSAH in case C showed the lowest values of the exergy destruction and improvement potentials.
In brief, the RSAH with CCu-BP exhibited the highest increment of exergy efficiency (51.6%) under an airflow rate of 0.0244 m 3 /s (condition C) compared to the SSAH with the same coating. Since, in the case of condition C (Re = 2850), which lay in the transition region, from the laminar to turbulent flow showed a decline in exergy performance in this region (this behavior was noted in [11,30]). In the current study, the decline was much more for the SSAH, but for RSAH, the declination was lower because of the increase in turbulent intensity with the steady effect of the lost energy due to the increased flow rate of air. Therefore, in airflow condition C, the ratio between the RSAH and SSAH was higher and had the lowest values of exergy destruction and improvement potentials.  The irreversibility of both RSAH and SSAH and their "improvement potentials" were estimated and the results revealed in Table 5, where there is a reciprocal relationship between exergy destruction and exergy efficiency as well as a temperature difference since the exergy loss is minimal when the thermal efficiency is optimum. The RSAH showed lower energy destruction and improvement potentials compared to SSAH. Furthermore, for the RSAH, the airflow rate in case D was the highest in energy destruction and improvement potentials compared to cases A, B, and C because of the high-pressure drop across the duct. In contrast, the RSAH in case C showed the lowest values of the exergy destruction and improvement potentials. In brief, the RSAH with CCu-BP exhibited the highest increment of exergy efficiency (51.6%) under an airflow rate of 0.0244 m 3 /s (condition C) compared to the SSAH with the same coating. Since, in the case of condition C (Re = 2850), which lay in the transition region, from the laminar to turbulent flow showed a decline in exergy performance in this region (this behavior was noted in [11,30]). In the current study, the decline was much more for the SSAH, but for RSAH, the declination was lower because of the increase in turbulent intensity with the steady effect of the lost energy due to the increased flow rate of air. Therefore, in airflow condition C, the ratio between the RSAH and SSAH was higher and had the lowest values of exergy destruction and improvement potentials.

Conclusions
Artificial roughness in the form of repeated ribs is an effective way to improve the quality of SAHs. Ribs split the viscous sub-layer and created local wall turbulence due to fluid separation and reattachment without disrupting the central turbulent stream, resulting in an increase in the convective heat transfer coefficient between the air and heated surface. Therefore, in this study, a novel solar selective coating consisting of 4% CNTs/CuO-black paint was used to coat a SAH roughened with aluminum broken arc ribs. Under four airflow rates, the RSAH was evaluated in light of the First and Second Laws of Thermodynamics and compared to the SSAH coated with the same coating. The results can be concluded as follows: (1) The maximum value of incident solar radiation was 922 W/m 2 on 29 October, and the averaged ambient temperature ranged from 20.8 • C to 30.3 • C during the experiment days. (2) The difference between the outlet and inlet of RHAS increased by 1.3, 8, 19.8, and 3.3 % for A, B, C, and D airflow conditions, respectively, over that of the SSAH.
RSAH with CCu-BP showed a higher heat transfer coefficient (W/m 2 . • C) and Nusselt number compared to the SSAH for each working volumetric airflow rate. (4) Employing broken arc ribs on the surface of the SAH's absorber coated with 4% CNTs/CuO-black paint increased the thermal efficiency by 0.8, 7.4, 18.4, and 1.9 % for cases A, B, C, and D, respectively, compared to the SSAH. The RSAH with CCu-BP exhibited the highest increment of exergy efficiency (51.6%) under an airflow rate of 0.0244 m 3 /s (condition C) compared to the SSAH with the same coating and had in addition, the lowest values of exergy destruction and improvement potentials. (7) Overall, the RSAH with CCu-BP under the airflow rate of 0.0244 m 3 /s (condition C) exhibited the best energetic and exergetic performance.

Conflicts of Interest:
The authors declare no conflict of interest.