Introduction to the Dynamics of Heat Transfer in Buildings

: Changing climatic conditions cause the variability of the parameters of the building’s surroundings, which in turn causes both the gains and losses of heat to change over time. There is variability in both daily and annual cycles. Meeting the requirements of thermal comfort in rooms requires maintaining the required parameters, including constant temperature. Heat gains and losses must be balanced, and this balance is ensured through appropriate heating systems. At the same time, the above means that the demand for heating buildings is not constant but depends on external weather conditions and the energy efficiency of the building. This, in turn, affects the thermal inertia, causing changes in the partition temperature to occur slower than the changes in air temperature. Therefore, the amplitude of the heating power changes is not proportional to the amplitude of the outside air temperature change. The paper presents an example of the analysis of thermal dynamics in buildings. Various aspects of heat transfer in the building were investigated taking into account the transient conditions. The variability of temperature over time at different depths of the partition was analysed, showing the results graphically. The periodic variability of the outside air temperature and the intensity of solar radiation were described by the Fourier series. Moreover, the article shows the influence of the thermal insulation thickness of the external wall on the annual amplitude of temperature changes and on the duration of the heating season, which is important from the point of view of optimization.


Introduction
The issue of heat transfer dynamics is closely related to the subject of the energy efficiency of buildings, which is important at the design and construction stages, as well as during the operation of buildings or their parts. This is visible in many legal regulations and policies aimed at improving the energy efficiency of buildings. This is due to the fulfillment of the provisions of Art.  [4] and Art. 40 of the Act of 29 August 2014 on the energy performance of buildings [5]. According to Directive (EU) 2018/844 of the European Parliament and of the Council of object-oriented Modelica in the paper [32]. Methods based on the coupling of three different types of simulation models, namely spectral optical model, computational fluid dynamics model, and building energy simulation, are presented in [33]. Physical phenomena, notably optical, thermodynamic, and fluid dynamic processes, have been analyzed for commercial buildings with double-skin façades. The modelling of heat transfer taking advantage of heat energy accumulation in building walls is the goal of the work [34]. The paper is focused on the future optimization of a control strategy. The issue of simulating heat transfer through point thermal bridges is the subject of the paper [35].
On the basis of the literature analysis of the subject of this work, it can be stated that there is a lack of ordering and development of methods for analyzing heat transfer dynamics using changeable external conditions. Existing works in this field mainly deal with the issues of energy control and control of the HVAC system's parameters, while there are no studies taking into account the changeability of atmospheric conditions and their impact on the dynamics of heat transfer. We realize that this is important in a changing climate, where the heating season and the summer season stand out. The issue presented in the article may be helpful in the analysis of the thermal inertia of a building in order to optimize the operation of HVAC systems.
The literature review presented in the article confirms that the approach to dynamics of heat transfer in buildings, proposed in the manuscript, is innovative with regard to the analysis of the impact of the variability of external conditions on energy efficiency and it was not previously applied in this way. This issue was the subject of this work.

Methodology
The room can be treated as a closed object, limited by building partitions, located in the space, treated as the surroundings. Due to the lack of a thermodynamic equilibrium between them, there are energy interactions between the room and the surroundings. To explain it simply, there is a heat transfer, considered as heat losses or gains. The thermal balance includes heat fluxes presented schematically in Figure 1. Heat gains from people Ql, from devices Qu, and from lighting Qe can be taken together as internal heat gains Qw.
(1) Due to variable environmental parameters, both heat gains and losses change over time. For a room to be kept at a constant temperature, the heat gains and heat losses must be balanced, and this balance is ensured through appropriate heating systems. At the same time, the above means that the demand for heat for heating facilities is not constant but depends on external weather conditions. The weather conditions that determine heat exchange are the temperature of the outside air and solar radiation.
Due to the thermal inertia, changes in partition temperature are slower than changes in air temperature. Therefore, the amplitude of changes in heating power Qg is not proportional to the amplitude of outside air temperature change Te.
The equation for the heat balance of the room is as follows: (2) The individual components of Equation (1) have been explained below. Heat transferred from indoor air to the wall: Heat transferred from indoor air to interior walls: The heat of solar radiation penetrating the window [8]: Heat from internal sources: • Heat to prepare the ventilation air: Heat loss through the window: The temperature of the internal surface of an outer wall is a result of the influence of the inner environment and the heat conduction in this wall.
The heat conduction in the wall is caused by the temperature distribution, which is unsteady due to changing external climatic conditions.
The temperature of the outer surface of the outer wall is influenced by the transfer of heat to the outside air, the absorption of solar radiation, and the emission of radiation to the sky.
Heat transferred from the outer wall surface to the outside air: Radiant heat losses from the outer wall to the skyfall: Solar radiation of heat absorbed by the outer surface of the outer wall [8]: Signs: αi-coefficient of heat transfer from the wall surface to the internal air, αe-heat transfer coefficient from the external wall surface to the outside air, Asi-the surface of the outer wall inside the room, Asw-the surface of the internal walls of the room, Ase-the outer surface of the outer wall, Af-reference surface (floors), Ao-window area, V-ventilation air stream, qA-indicator of internal heat sources, VVe-ventilation rate, z-shading coefficient, ws-radiation transmittance coefficient, σs = 5.67 × 10 −8 [W/m 2 K 4 ]-radiation constant, εsn-radiation absorption coefficient of the outer surface of the outer wall, εs-radiation emission coefficient of the outer surface of the outer wall, I-solar radiation intensity, Ti-internal air temperature, Te-outside air temperature, Twi-temperature of the inner surface of the outer wall, Tsw-surface temperature of internal walls, Twe-external wall surface temperature, Tn-skyfall temperature.
Equation (2) shows the required heat output to heat the room during the heating season.
The use of a heating device with the required thermal power and automatic temperature control results in maintaining the room temperature in accordance with the regulations [7] In most cases, this temperature is taken as a constant value (Ti = const). Outside the heating season, the heating devices are turned off (Qg = 0), and the internal air temperature is determined based on the thermal balance.
After using the thermal balance equations and transformations, the internal air temperature is described by the equation: Due to the variable temperature of the external air, outside the heating season also the temperature of the inside air is variable. The temperature of the inner surface of the walls is also variable.
This temperature is the result of heat transfer through the external wall between the room and the outside air.
With the simplifying assumption that the outside air temperature changes periodically according to the cosine function, the solution to the problem of heat conduction in a semi-infinite medium is described by the equations, according to [36,37]: It was assumed that the air temperature changes according to the equation: in which where: Tfo-amplitude of air temperature changes, t-time, ω-period of temperature changes, to-change period time, ν-frequency of changes, The temperature T at depth x, below the surface, is described by the following dependencies: where: λ-thermal conductivity, a-thermal diffusivity of the area, α-coefficient of heat transfer from air to the surface.
The constant C1 determines the degree of air temperature reduction resulting from the transfer of heat, while the constant C2 means the delay in wave propagation due to the transfer of heat to the surface.

Dynamics of Heat Transfer through an External Wall-Case Study
The external wall of the room is subjected to variable outside air temperature. Moreover, the external surface is influenced by the variable intensity of solar radiation. Climatic conditions cause periodic temperature variability in daily and annual cycles. Climate changes also cause changes in the temperature of external surfaces such as external building envelopes. Surface temperature changes are transferred deep into the material according to the principles of heat transfer. With a sufficient wall thickness, it can be treated as a semi-infinite medium for which the heat conduction problem has been analytically solved.
The tendencies of temperature changes in the semi-infinite medium is shown in Figure 2. A negative coordinate x indicates temperature changes in the adjacent fluid. The graphically presented temperature changes in the medium and equations [36,37] allow for the following conclusions:

•
There are temperature oscillations in the material with the same period in each plane, but with a phase shift in relation to the surface.

•
The amplitude of temperature changes on the surface is smaller than the amplitude of changes in air temperature (C1 < 1).

•
There is a phase shift in temperature changes (C2 < 0).

•
The amplitude of temperature changes in the material quickly decreases with depth.

•
The lower the frequency of temperature changes, the greater the amplitudes at the same depth.
The variability of temperature over time at different depths is shown in Figure 3. The presented considerations apply to a semi-infinite medium. However, they may be the basis for the analysis of temperature distribution in media with a finite, sufficiently large thickness. An example of such a medium are the external walls of a building, which is influenced by external air of variable temperature. There is a daily and annual periodicity of changes. Daily changes do not significantly affect the temperature distribution inside the wall under the surface, especially on the inner wall surface (from the room side). Annual changes, on the other hand, affect heat losses and, consequently, seasonal heat demand for heating.  In relation to the semi-infinite medium model, the following differences should be taken into account: • Changes in outside air temperature are periodic, but a description of the changes with a simple cosine function would be a simplification. • In addition to the transfer of heat between the outer surface and the air, there is a heat exchange by radiation (solar radiation). • The outer wall is usually multi-layered and therefore heterogeneous.
The periodic variability of outdoor air temperature and solar radiation intensity can be described by the Fourier series of the form [39]: The coefficients of the Fourier series should be determined on the basis of real data obtained, e.g., from measurements.
The temperature of the outside air and the intensity of solar radiation are climatic parameters and they are measured at meteorological stations. The results of long-term measurements are available on the website of the Ministry of Infrastructure [40].
For the selected weather station, we can read the average monthly and hourly average outside temperature values determined from multi-year measurements. Using these values, data can be approximated by a Fourier series. For the Rzeszow-Jasionka meteorological station, the annual changes in the values of average daily outside air temperatures are shown in Figure 4, where the line resulting from the approximation of the data by the Fourier series (Te (apr)) is also plotted.  The parameters of the Fourier series for approximation calculations of the outside air temperature are presented in Table 1.  As can be seen from the diagram, there is a high agreement of the measurement data with the results obtained from the approximation equation. Significant differences occur in the summer, outside the heating season.
A similar procedure can be applied to record the variability of solar radiation, but due to the consideration of the external wall, only the radiation to the vertical plane will be important.
The Fourier series parameters for the approximation calculations of the radiation intensity per vertical surface (Wh/m 2 d) are summarized in Table 2. Exemplary results for the Rzeszow-Jasionka actinometrical station are shown in Figure 5. The comparison of the measurement results and those calculated from the Fourier series equation for the direction of the southern and northern radiation is presented in Figure 5.
Marking N in Figure 5 depicts the radiation changes from the North. Labeling S denotes imaging of changes in radiation from the southern side. Marking N-a represents the results of approximation of radiation changes from the North using the Fourier series. Then, by analogy, S-a refers to the results of the approximation of radiation changes from the south side.
Remarks on the compliance of the approximation with the data are the same as in the case of the approximation of the outside air temperature.
Increasing the accuracy of the approximation is possible by increasing the amount of Fourier series components. For the assumed purpose of the analysis of the temperature distribution in the external wall, the assumed accuracy is sufficient.

Heat Losses through the External Wall-Case Study
The external wall separates the outside environment and the interior of the room. Such a wall is subjected to an externally variable air temperature as well as solar radiation. Climatic conditions cause periodic temperature variability as well as the variability of radiation intensity, and these changes occur in daily and annual periods. The resulting wall temperature distribution makes it difficult to provide a strict analytical solution, especially in the case of a multi-layer partition, Simplified methods can be used to solve special cases, e.g., the finite difference method (MRS). The analysis of heat loss through the external partition is made below, with the following assumptions. On the side of the inner wall (in the room), the air temperature remains constant. This is the case during the heating season with automatic temperature control (thermostatic valves).
The heat transfer from the inside air to the surface takes place by transfer, with a transfer factor taking into account the radiation.
On the outer side of the outer wall, heat is transferred to the outside air by taking over.
On the outer side of the outer wall, heat transfer also takes place through radiation to the outer space (the sky).
The outside air temperature changes throughout the year according to the climatic conditions. Solar radiation falls on the outer surface of the wall with periodic, annual variability. The values of external temperature and radiation intensity were taken as daily averages.
The image of the partition in question, with significant values marked, is shown in Figure 6. The variable temperature distribution in the wall was determined by the finite difference method based on heat transfer equations, taking into account the thermal balance of the room.
Due to the variable temperature of the outside air, the temperature of the inside surface of the outside walls is also variable.
This temperature is the result of heat transfer through the external wall between the room and the outside.
When applying the finite difference method (FDM) to solve the transient heat conduction in the outer wall, formulas based on the calculation scheme are obtained (Figure 7). The formulas resulting from the discretization of areas were used for the calculations. Inner surface temperature of outer wall: Surface temperature at the boundary of the layers: The temperature of the outer surface of the outer wall was determined from the balance sheet ( Figure 8): Taking into account the Equations (10)- (12) and the heat conduction equation under the surface of the partition (24), it can be concluded that: After substitution and transformations, the temperature of the outer surface of the outer wall is described by the relationship: Due to the presence of Twe, the equation is solved by the iteration method. Signs: Tn-skyfall temperature σs = 5.67 × 10 −8 [W/m 2 K 4 ]-radiation constant εs-surface radiation absorption coefficient εsn-surface radiation emission coefficient αe-heat transfer coefficient from the external wall surface to the outside air λ2-thermal conductivity coefficient of the insulating layer Δx2-step of discretization of the insulating layer The above equations are completed with boundary conditions. • The heating season was assumed to occur during the period when the outside air temperature is lower than 12 °C (Te < 12 °C).

•
If, during the heating season, the heat losses are greater than the heat gains, the heating control system maintains a constant internal temperature (Ti = Tio). • If in the heating season the heat losses are lower than the heat gains, the control system switches the heating off and the internal temperature results from the thermal balance. • Outside the heating season, the internal temperature results from the thermal balance.

Assumptions and Output Parameters
Using the previously given equations, calculations of the parameters of the room and the external partition were made for variable external conditions [41].
The calculations were made for several variants of rooms with general assumptions: The heat transfer coefficient on the inside and outside is constant in accordance with the standard [42]. • Natural ventilation with the intensity resulting from meeting the requirements of the standard [43]. • The thermal conductivity coefficient of the wall construction material and insulation is constant. • Internal heat gains are constant.
Relationship between VVe coefficient and the number of exchanges n: h-room height.
Thermal conductivity: Meteorological data: Sample calculations were made using the meteorological data for the Rzeszów-Jasionka measuring station.
The table of hourly changes in outside temperature and changes in the intensity of solar radiation was used, provided by the website of the Ministry of Infrastructure [40].
The example assumes the location of the outer wall towards the north. It is assumed that the final result of the calculations will be the determination of the variability of the heat demand for space heating over the year, taking into account the variability of climatic conditions and the inertia of building partitions.
The basis for determining the heat demand is Equation (2). The components of the equation were determined by Equations (3)-(10) using the assumptions made above.
The calculations were made for a living room with an external wall made of brick, 50-cm thick, for the cases: without insulation and with insulation with a layer of polystyrene 5-, 10-, 15-, 20-, and 25-cm thick. The results of the calculations are presented in the following charts.

Calculation of Indoor Air Temperature
In the heating season, the heat losses exceed the heat gains in the room, which are supplemented by the heating system. The regulation of this system allows for the maintenance of the constant temperature Ti = 20 °C, assumed in the example. In summer, the temperature of the indoor air is the result of the heat balance of gains and losses. Temperature fluctuations increase as the thickness of the insulation increases.
The calculation results of the average daily temperature of indoor air obtained using the Equation (14) are presented graphically in Figure 9. During the heating season, the regulation ensures a constant temperature. In summer, there is a temperature change, and these fluctuations increase with increasing insulation thickness. The labels in Figures 9 and 10 were signed by adding units of insulation thickness as "Ti-0 cm" and analogously "Twi-0 cm". From the graph in Figure 9 you can read the time during which heating is required, i.e., the duration of the heating season. This time depends on the insulation of the outer wall (insulation thickness).

Calculation of the Surface Temperature of the Inner Outer Wall
The temperature of the inner surface of the outer wall is the result of heat conduction through the wall and taking heat from the inner air. It clearly depends on the wall insulation. It was calculated according to the Equation (22) and the results are presented in Figure 10. This temperature and its fluctuations throughout the year clearly depend on the wall insulation.
The annual amplitude of changes in this temperature decreases with increasing insulation thickness. In the absence of insulation, the lowest temperatures appear around the beginning of March, and for an insulated wallm around mid-April.
Fluctuations in the average daily temperature ΔTi (Figure 11) with efficient regulation in the heating season are very small during the year (<0.51 °C) and depend to a small extent on the wall insulation. On the other hand, the temperature fluctuations of the inner surface of the outer wall Twi depend on the insulation. For a wall without insulation, the maximum difference in a year is 3.14 °C. The difference in temperature values when changing the insulation thickness from 5 to 25 cm, equal to 0.49-0.86, is small and it has little effect on thermal comfort.

Analysis of Thermal Power Variability for Heating Purposes
Using the proposed methodology, calculations of thermal power for heating were performed for the conditions assumed in Section 2. The diagram given in Figure 12 shows the dependence of this power on the insulation thickness.

Insulation thickness x [cm]
DTi DTwi The chart of changes in heat demand for heating ( Figure 11) clearly shows the division into the heating season and the summer season. The demand in the heating season depends (which is obvious) on the insulation of the outer wall. The length of the heating season tg also depends on the insulation performance.
The maximum heat output, which is the basis for the selection of heating devices, is also different for each case. The comparison of these powers is shown in Figure 13. The diagram also includes heating powers Qmaxn calculated on the basis of the applicable standards. Qmax denotes the maximum thermal power for a given case of the partition structure, calculated according to the considered methodology. Qmaxn means the maximum thermal power for a given case of the partition structure, calculated on the basis of the applicable standard PN EN 12831 titled "Heating installations in buildings. Design heat load calculation method". Among the calculated thermal powers presented in Figure 12, the maximum powers Qgmax necessary to ensure thermal comfort were selected. Such powers Qgmaxn were also calculated for the considered cases in accordance with the standard. The values are presented in the Table 3 and in the diagram in Figure 13. The following conclusions can be drawn from the presented values: • Taking into account the thermal inertia of the partitions makes it possible to perform a significant reduction in the demand for thermal power, and thus the use of smaller devices. • For the considered partition, the calculated thermal power determined by the adopted method is only about 40% of the value calculated according to the standard. • The reduction in thermal power depends on the thermal inertia of the partitions. • Due to the low thermal capacity, the insulation thickness has a little effect on the maximum heat output.

The Dependence of the Time of the Heating Season on the Thickness of the Insulation
The dependence of the length of the heating season on the insulation thickness is shown in Figure 14.

Insulation thickness x [cm]
Qgmax Qgmaxn The diagram in Figure 14 clearly shows the dependence of the heating season on the "insulation" of external walls. Increasing the thickness of the insulation shortens the heating season, which contributes to reducing the annual heat consumption for heating purposes. For comparison, the graph also shows (red) the time determined on the basis of the annual variability of the outside air temperature. This time is approximately in line with the calculation method adopted for the wall without external insulation (x = 0). This confirms the correctness of the adopted calculation methodology and the correctness of the performed calculations.

Validation of the Model by Using Fragmented Temperature Measurements
In order to assess the compliance of the adopted calculation methodology with the actual conditions, fragmentary temperature measurements were performed. Measurements were made in a real facility in a single-family residential building, on an external brick wall with the following parameters: • Wall thickness: 50 cm, • Thickness of the outer polystyrene insulation: 10 cm • Thermal conductivity of the wall: λ = 0.82 W/(m·K) • Thermal conductivity of the insulation: λ= 0.032 W/(m·K) Following temperatures measurements were taken: • Ti-internal air temperature • Twi-temperature of the inner surface of the outer wall • Te-outside air temperature The purpose of the measurements is to show the effect of thermal inertia of the partitions on the changes in internal temperature. The measure of the influence of inertia is the amplitude of changes in the internal temperature and the temperature of the internal surface of the external partition as a function of the amplitude of changes in the external air temperature.
Measurements were taken continuously and the values were averaged over an hourly period for analysis.

Insulation thickness x [cm] t g [Days]
This impact was initially analyzed on the basis of measurements conducted from 20th to 29th February 2020 and from 18th to 20th July 2020. The results presented in the table below were obtained for these cases. Results of calculations and measurements have been presented in Table 4. Exemplary results for several hours in the heating season (February) are shown in Figure 15 as a function of successive hours throughout the year. The graph also shows the corresponding temperatures for these hours obtained from calculations (Tio, Twio, Teo). On the horizontal axes of the graphs (Figure 15 and following), the time is defined as successive hours of the year. Such a system was adopted for the purpose of comparing the results of measurements and calculations, because the calculations used climatic data for the following hours of the year. The hours for calculations and measurements were kept consistent.
Supplementary markings: • Ti-measured internal air temperature • Te-measured outside air temperature • Twi-measured temperature of the inner surface of the outer wall • Tio-internal air temperature adopted for calculations • Teo-outside air temperature taken for calculations • Twio-calculated temperature of the inner surface of the outer wall During the heating season with variable outside air temperature, there are small changes in the temperature of the inner surface of the outer wall. The temperature value is comparable with the value calculated according to the adopted method.
In the summer, we can observe a similar tendency. A detailed comparison will be the purpose of further research. We initially present sample measurement results for summer season. We presented obtained results of researches in the Figure 16. In order to verify the correctness of the adopted methodology, the amplitudes of differences in temperature between the internal air and the internal surface of the external wall were determined and presented in the Table 5. During the measurement period, there were significant fluctuations in the outside temperature and due to this there were also changes in the internal temperature, despite the regulation of the heating with a thermostatic valve. For this reason, there was a change in the temperature difference between the inside air and the wall surface. The course of amplitude changes during the period from 20 to 29 February 2020 is shown in Figure 17. Analogically, the course of amplitude changes during the time from 18 to 20 July 2020 is presented in Figure 18.

Tio-Twio
In order to verify the correctness of the adopted methodology, additional, more precise temperature measurements were made for the period from 9 to 17 November 2020. The measurement results are shown in Figures 19 and 20.  The measurement results were compared with the values used in the calculations in the adopted model and are presented in Table 6. The influence of the thermal inertia of partitions on changes in internal temperature was analyzed. The results of measurements and calculations are shown in Figure 20.
Changes in the temperature of the outside air cause slight changes in the temperature of the inside surface of the outside wall. The value of the wall surface temperature is comparable with the value calculated in accordance with the adopted method, which is shown in Figure 20.
In order to better visualize the compliance of the measurement results with the calculations, relative deviations calculated on the basis of the differences in the measurement and calculation results were determined. The deviations were applied to the temperature of the inner surface of the outer wall, because this temperature determines the transfer of heat for all three analyzed measurement series. when: δ-relative deviation of the measured and calculated internal surface temperature.
The changes of the relative deviations of the values measured for the period from 9 to 17 November 2020 is shown in Figure 21. The relative deviations for all three measurement series are presented in Table 7.  A small value of the average deviation of the measurement and calculation results during the heating season indicates the correctness of the adopted analysis method. The big difference in July is caused by very large changes in outside air temperatures, deviating from typical meteorological years. It should be emphasized that such a result is obtained from measurements of a real object (not in a laboratory) under very variable climatic conditions. Moreover, the temperature of the indoor air in the summer with no air conditioning is directly related to the temperature of the outdoor air and is not regulated.
Furthermore, complete measurements are planned to fully assess the compliance of the calculation model.
The presented data show the following conclusions: • In the winter period (February), the measured amplitude of changes in the outside temperature of 11.50 °C corresponds to the amplitude of changes in the internal temperature of 1.30 °C and the amplitude of changes in the temperature of the inside surface of the external wall, which equals 1.00 °C. • Similar relations exist for the period from 18 to 20 July 2020. • In any case, the average amplitude of changes in the temperature of the internal surface of the external wall is smaller than the amplitude of changes in the temperature of internal air. • The same conclusion follows from the calculation results. Quantitative differences are caused by the random selection of the measurement period and the uniqueness of the climate parameters. • Reducing the amplitude has a positive effect on maintaining thermal comfort.

Summary and Conclusions
The current regulations define the rules for calculating the heat demand for heating based on the difference between the maximum and minimum outside air temperature for the climate zone. The calculations do not take into account the thermal inertia of building partitions.
The main aim of the article is to determine the influence of the thermal inertia of building partitions on the building's heating system, taking into account changing climatic conditions.
The process of heat transfer through the partitions is described in the literature, and the novelty in this respect is the use of boundary conditions appropriate for the nature of the partition, i.e., variable outside air temperature and solar radiation intensity. These conditions are taken into account in the literature-also in standards-, but in a simplified way through indicators covering longer periods (usually monthly). This variability is not considered when constructing an ordered diagram of heat loads, which affects the determination of the heating season time.
The thermal power of heating devices is assumed on the basis of calculations made for the steady state with extreme parameters, without taking into account the thermal inertia. In the presented study, the influence of the thermal inertia of the external building partition on the heat exchange between the building's interior and its surroundings was analyzed. Different thicknesses of the insulation of the outer partition were considered. The ongoing dynamic processes were analyzed computationally using the finite difference method (FDM).
Based on the obtained calculation and measurement results, the following conclusions can be drawn: • Maximum power for heating, determining the selection of heating devices, is lower than the values determined according to the applicable calculation rules. The difference between the thermal power calculated on the basis of the applicable PN EN 12831 standard and the maximum power for a given case of the partition structure, calculated in accordance with the considered methodology presented in the article, decreases with increasing insulation thickness and equals from 41% to 24%. • The reduction in heat output depends on the thickness of the insulation, but to a much lesser extent than the increase in thickness. The economic correlation between these values requires further analysis. • The duration of the heating season is also dependent on the insulation of external partitions and it is definitely shorter than that determined on the basis of changes in external temperature. • With the efficient regulation of the internal temperature in the heating season, the insulation of the external partition allows for very small temperature fluctuations of the internal surface of the partitions, which has a positive effect on the thermal comfort of the rooms.

•
The results of the research on temperature variability over time presented in the article confirm the fact that the temperature fluctuations of the surface of the partitions, which reflect the heat transfer from the internal air to the partition surface, and the heat conduction inside the partition and heat transfer from the partition to the outside air are much less variable than the fluctuations of outdoor and indoor temperatures. With the amplitude of changes in the outside air temperature in summer amounting to 11.5 °C, the amplitude of changes in the internal temperature of the surface of the analyzed external wall is 1.00 °C, while the amplitude of changes in the internal temperature is 1.30 °C. In winter, these fluctuations demonstrate similar relationships with greater differences.

•
The performed research confirms the compliance of the adopted model of heat transfer dynamics testing. Average temperature deviations measured and calculated in the winter season range from −0.85% to +0.45%. A significant deviation in the summer season is due to the lack of temperature regulation.
The development of issues related to the dynamics of heat transfer, taking into account the variability of weather conditions and thermal inertia in buildings, will be the subject of future research conducted by the authors of this article.