Gel Pills for Downhole Pressure Control during Oil and Gas Well Drilling

: During drilling of petroleum or geothermal wells, unforeseen circumstances occasionally happen that require suspension of the operation. When the drilling ﬂuid is left in a static condition, solid material like barite may settle out of the ﬂuid. Consequently, the induced hydrostatic pressure that the ﬂuid exerts onto the formation will be reduced, possibly leading to collapse of the borehole or inﬂux of liquid or gas. A possible mitigation action is placement of a gel pill. This gel pill should preferably be able to let settled barite rest on top of it and still transmit the hydrostatic pressure to the well bottom. A bentonite-based gel pill is developed, preventing ﬂow of higher density drilling ﬂuid placed above it to bypass the gel pill. Its rheological behavior was characterized prior to functional testing. The designed gel pill develops su ﬃ cient gel structure to accommodate the settled barite. The performance of the gel was tested at vertical and 40 ◦ inclination from vertical. Both conventional settling and the Boycott e ﬀ ect were observed. The gel pill provided its intended functionality while barite was settling out of the drilling ﬂuid on top of this gel pill. The barite was then resting on top of the gel pill. It is demonstrated that a purely viscous pill should not be used for separating a high density ﬂuid from a lighter ﬂuid underneath. However, a bentonite or laponite gel pill can be placed into a well for temporary prevention of such intermixing.


Introduction
Drilling fluids are concentrated fluid-solid mixture whereas high density minerals such as barite with a density of 4.2 s.g. (specific gravity) are used to increase and adjust the density of drilling fluid. As density of the heavy minerals is much higher than the fluid density, gravitational force acts on these particles making them segregate and finally settle out of the fluid. A review of the phenomenon, better known as weighting material sag, and possible measurement methods is found by consulting Ofei et al. [1]. The sagging effect occurs both in water-based and oil-based drilling fluids. However, it appears to happen faster in oil-based drilling fluids [2,3]. Saasen et al. [4] showed that barite sag can be more intense in fluids that develop fragile gel structures when left static. They defined a fragile gel structure fluid as a fluid with high gel strength, but when the initial gel structure is ruptured, the remaining gel structures will easily break. Thus, a drilling fluid may have high gel strength, but when exposed to small shear rates, its solid particles can start to settle fast. Barite settling is known to cause problems during drilling operations with the most severe consequence leading to well control issues. This is due to the reduction of hydrostatic pressure exerted by the drilling fluid.
The sag phenomenon in a vertical, static drilling fluid column is controlled by viscosity and gel formation. As the barite particles move downwards because of gravity, a fluid motion is set up in the opposite direction to preserve the fluid mass balance. This counterflow may contain solid particles smaller than the sagging particles. Hence, the sag velocity is reduced. This is illustrated in Figure 1a. If the static fluid column is inside a tilted pipe, the sag will be accelerated by the so-called Boycott effect [5]. If the barite particles travel vertically downwards, a less dense fluid layer will be placed above a denser layer in a tilted tube. This will trigger a flow of light fluid upwards and a dense fluid downwards in the well, as illustrated in Figure 1b, accelerating the settling process. This process continues until most weight material particles have reached the well bottom. As barite starts to settle out from drilling fluid, the uniform distribution of barite decays resulting in a higher density fluid at the lower part and a lower density fluid at the higher part of the fluid column. This results in a static fluid system that no longer provides a constant hydrostatic pressure gradient throughout the fluid column. When the barite particles rest on a bed, the hydrostatic pressure of fluid column will be lost. This phenomenon can lead to the well bore pressure being in underbalance with respect to formation pressure, potentially causing influx of liquid or gas into the well.
The intensity of barite sedimentation is function of drilling fluid characteristics, such as particle size, concentration of particles, surface charge of particles, and operational circumstances such as flowrate or induced stresses caused by drilling activities, and distance between the particle and bedding distance [4][5][6][7]. Nguyen et al. [8] showed that if the fluid is left in static conditions, the barite sag will not occur if the yield stress of the fluid is higher than approximately 6 Pa (12 lbf/100 ft 2 ). This statement, however, shows the difficulty in determination of the yield stress. By a force balance, it is easily shown that the barite particle should not move if it is exposed to a fluid with a real yield stress exceeding half a Pascal.
Previous studies on barite sedimentation mechanisms showed that in inclined pipes, from vertical to 20 • and 40 • , the contribution of gravity and Boycott effect on barite settling was observed. It was also observed that the hindered mechanism affected the settling time on the suspended barite particles in water-based drilling fluids as inclination was changed from 40 • to vertical [5,9]. In drilling operations, there are circumstances where maintaining the hydrostatic pressure profile at the bottom of well or at a desired depth is necessary when the drilling operation is temporarily suspended.
A viscous pill has been tried as a liquid packer placed above the formation with influx potential, to collect the sagging weight material and thus provide proper pressure at this formation. However, a viscous fluid alone will be prone to Rayleigh-Taylor instability [10] where the dense fluid will flow downward, and the lighter fluid will flow upward. The interface will be even more unstable if it is placed in a deviated section as longer disturbance lengths are less stable than the shorter; this also occurs in the case of polymeric liquids [11,12]. This was the reason for the use of the umbrella-like tool placed in the well for plug cementing purposes [13].
A proper gel pill could be placed just above the formation with the potential of fluid influx, and would hold the settled barite while ideally still transmitting the pressure exerted by the fluid and barite above the pill to the formation below the pill. This pill needs to be properly gelled to prevent formation of Rayleigh-Taylor instability. Gel is defined as a soft colloid that is elastic, deformable, and solid. It is made of colloidal particles together with polymers, which together construct a nonliquid network. When considering the microstructure of gel at microscale, it is "liquid," and when considering it at macroscale, it is "solid" [14]. A viscous fluid is liquid with a relatively high viscosity. A viscous pill is usually used for special tasks such as cuttings transportation, lost circulation treatment, or removing filter cakes.
Fosso et al. [15] emphasized that for a Bingham plastic with a proper yield stress of τ y in a pipe with diameter of D, if the pressure gradient does not exceed 4τ y D , the fluid above the gel pill will remain in stable condition and no flow will occur. A yield stress is the minimum gel strength of a material. Harestad et al. [13] showed that the maximum pressure difference the gel ideally needs to hold is a density difference across the well cross-section if the fluid above the gel is carefully positioned. Hence, the necessary length of a gel pill is as short as possible to ensure proper placement over the entire pill length.
Inside a pipe, a proper gel pill will always hold back a pressure difference equal to the value shown in Equation (1): where τ g is the gel strength, D is the pipe diameter, and ∆L is the pill length. This equation is found by conducting a simple force balance. Settled barite may prevent the force transmission. For a layer of completely settled barite particles, any force transmission will be conducted through direct particle-particle contacts. Since these particles have different shapes and sizes, it is not possible to exactly predict the angle of attack between the particles. However, it is anticipated that this would be around 45 • . Therefore, pressure transmission may be hindered when the height of the settled barite exceeds the pipe diameter. Any pressure increase after this condition has occurred will only apply more normal forces on the pipe wall.
The primary objective of this study was to evaluate a pressure transmitting gel pill that can act as a resting bed for settled barite particles. In addition, the gel pill should prevent any tendency for Rayleigh-Taylor instability or breakthrough of sagged barite staying on top of the gel pill. The gel pill should establish full pressure transmission of the overlying fluid column to maintain constant hydrostatic pressure underneath the pill. Subobjectives were to evaluate a gel pill with low viscosity during placement and high viscosity and gel strength after placement.

Benchtop Viscous Pill Test Overview
In practical operations, it has been common to apply viscous pills to prevent segregation of other fluids with higher density from above. In this section, it will be shown that use of viscous pills is insufficient to prevent a high density fluid to swap position with a lighter fluid underneath. This is Energies 2020, 13, 6318 4 of 16 demonstrated by placing a viscous pill in a benchtop tube. Thereafter, a 1.48 s.g. fluid is placed on top of the pill and measure if it will stay in place. A short wavelength disturbance is more stable than a long wavelength disturbance [11,12]. The wavelength of the disturbance will depend on the length of the interface between the fluids; the larger the diameter, the larger the wavelength. If the interface is unstable in the benchtop experiments, it will also be unstable in the larger scale tests. Therefore, only the successful cases from the benchtop tests were repeated in larger scale equipment tests.

Model Drilling Fluid and Viscous Pills
All of the fluids consist of tap water and Xanthan biopolymer. The model drilling fluid contains added barite to a density equal to 1.48 s.g. The full composition of the model drilling fluid is shown in Table 1. The viscous properties initially after mixing and after 24 h storage are illustrated by the flow curves shown in Figure 2. By comparing these flow curves with the huge number of flow curves of practical drilling fluids shown by Saasen and Ytrehus [16], it is shown that this model drilling fluid has a very low viscosity. This is beneficial for the experiments as the low viscosity promotes instability. Hence, the ability of the viscous or gel pill to hinder swapping of the fluids becomes more clearly visible.  The laboratory viscous pill formulations are shown in Table 2. Their flow curves are shown in Figure 3. Pill 1 has a viscosity behavior typically for a polymer-rich water-based drilling fluid, Energies 2020, 13, 6318 5 of 16 while pill 2 is far more viscous, the latter being too viscous to have the shear stress measured at the highest shear rate on an oilfield viscometer. Table 2. Mix design and mixing procedure for the viscous pills.

Ingredients
Pill 1 (g) Pill 2 (g) Tap water 350 350 Xanthan biopolymer 3.0 4.0 Xanthan concentration (g/L) 8.6 11.4 To prepare the fluids, a Heidolf Torque 100 mixer was used to mix small volumes and provide enough mixing energy to create the desired rheological behavior. For the larger scale testing, a Hobart mixer model N50-60 was used with a low stirring rate. The mixers have a type of blade which minimizes the physical damage to bentonite and laponite. The viscosity was measured using an Ofite 900 viscometer. The measurements were done at ambient conditions.

Performance of the Viscous Pills in the Benchtop Tests
The effect of the viscous pills was tested in a 0.5 m long benchtop tube with 50 mm inner diameter, as illustrated in Figure 4. The viscous pill was positioned at the bottom of the tube. Thereafter a volume of the model drilling fluid was placed above the viscous pill. Both for Pill 1 and the very viscous Pill 2, the fluid volumes immediately swapped positions. Figure 2 shows a picture of the final test result for Pill 2, photographed just after the swapping had occurred. As explained earlier, if the diameter had increased or if the hole angle deviated from vertical, the fluid case would be more unstable as the case becomes more unstable if longer wavelength disturbances are possible [11,12]. Hence, there was no use testing the viscous pills in larger holes or deviated holes.

Design and Development of Bentonite-Based Gel Pill
As described earlier, the scope was to construct a gel pill that can act as a resting bed for settled barite particles from the drilling fluid volume placed above the gel pill. To evaluate the desired properties of this gel pill, it was necessary to perform laboratory tests. Bentonite gels were found to be good candidates for such pills. Conventional bentonite pills will not be transparent and thus any sag effects of barite within the pill will be difficult to observe. Therefore, experiments were also performed using a transparent bentonite system. This was performed using the synthetic clay laponite [17] to make similar gel pills for laboratory investigations. The laponite gel pills should ideally have nearly the same rheological properties as the conventional bentonite pill. This pill was tested in a laboratory model representing a well bore at various inclinations. A viscosified brine volume was placed beneath the gel pill. The brine is used to increase the density contrast to the model drilling fluid placed above the gel pill and to simulate the presence of a low density drilling fluid volume left in the lower section of the hole. As explained earlier, the model drilling fluid placed above the gel pill is also a simple fluid using barite to increase the density. This fluid will not produce any significant gel strengths and will therefore increase the possibility of triggering Rayleigh-Taylor instability, and hence, provide a good test for the performance of the gel pill.
The gel pill designed for practical use was based on a conventional bentonite (Table 3). Bentonite consists of clay minerals, predominantly montmorillonite with minor amounts of other smectite group minerals, often used in drilling fluids to control the filter loss and viscosity of the fluid [18]. An API bentonite was used in this study. Different concentrations of bentonite were added to a base fluid. Their rheological behavior was characterized by use of a rotational viscometer both for viscosity determination and gel strength development, as measured in accordance with API specifications [19]. The main design criterion was rapid gel strength development. Furthermore, the gel pill design was optimized to provide sufficient viscosity at low shear rates, but still with a sufficiently low viscosity range at high shear rates so that the pill was pumpable. A strong thixotropy was initially observed for the bentonite pill. Therefore, the pill was left static for 48 h prior to viscosity measurements and the fluid pill tests. The performance of the bentonite system was compared with that of the laponite pill measurements. Laponite is a clay mineral without metal content [20]. It has basically the same properties as the bentonite. Being transparent in a water solution, any motion of barite particles can be captured. A commercial laponite (RD) delivered by BYK-Chemie GmbH was used in this study. The composition is shown in Table 4. The rheological behavior of the laponite gel differed only slightly from that of the conventional bentonite. A strong thixotropy was also observed for the laponite gel, however, not as strong as for the bentonite. For this fluid, the viscosity measurements became repeatable first after 24 h storage. The one day storage primarily led to an increase in the yield stress. Both the surplus stress, being the difference between the measured shear stress and the yield stress, at 102 1/s and the flow index, n, were nearly unaffected. The gel strength properties of the laponite gel seem to be nearly constant after 24 h storage. As a result of having a lower yield stress and a lower overall viscosity, the interface between the drilling fluid and the laponite gel would be prone to be more unstable than the interface towards the bentonite pill. Hence, use of the laponite pill represents a conservative test. The relevant rheological parameters for the experiments for the bentonite and laponite gel pills are shown in Figure 5 and Table 5. For both fluids, the 10 s gel strength is lower than the approximated yield stress. This indicates a strong thixotropy that starts developing at lower shear rates long before the fluids have reached a static condition. Similarly, the 10 min gel strength for the laponite system shows a much higher value than that of the conventional bentonite. Hence, for application in the test it may be expected that the laponite gel pill can withstand stronger forces than the bentonite pill. Per hole diameter length, following Equation (1), the gel can resist a pressure difference of four times the gel strength. Table 5. The yield stress measured in accordance with Zamora and Power [21,22], and gel strength measured in accordance with oilfield standards [19,23,24] for the bentonite and laponite system.

Shear Stress (Pa)
Bentonite Laponite Viscosified calcium brine and a simple model water-based drilling fluid were used, having the compositions shown in Table 6. The brine had a density of 1.3 s.g. and was placed in the base underneath the gel pills. The idea is that the brine shall model a drilling fluid left in the well prior to placing the gel pill. As can be observed from the measurements shown in Figure 6, the viscosity of the brine was close to constant and relatively low. Using the graph shown in Figure 6, it is reasonable to Energies 2020, 13, 6318 8 of 16 state that this viscosity is approximately 4 mPa·s. This low viscosity will challenge the gel pill as the low viscosity makes it very mobile.

Equipment and Test Setup
The gel pill has a density of 1.03 s.g. A 1.30 s.g. viscosified brine was placed beneath this pill. Finally, a water-based drilling fluid with a density of 1.48 s.g. was placed on top of the gel pill. Figure 7 shows a picture of the test column and a sketch of the interfaces placed between the fluids, and their Energies 2020, 13, 6318 9 of 16 measurement points. The drilling fluid was designed so that its barite particles would settle out of the fluid during a period of approximately one hour after placement. Table 4 shows the mix designs and mixing order of the fluids. A laboratory scale test setup made of transparent acrylic pipe is shown in Figure 7. The length of the pipe was 3.8 m and the pipe inner diameter was 49.7 mm. The setup was connected to a digital pressure gauge that read the pressure at the base of pipe. There were four penetrations with differential pressure probes to measure the changes in differential pressure, as indicated on the drawing in Figure 7. The four points in the center of tube indicate the differential pressure measurement points. At the bottom, there was a fifth penetration where the bottom hole pressure was measured. The setup was designed with the possibility of changing the inclination from vertical to 40 degree from vertical. The setup was equipped with two cameras to record the drilling fluid-gel pill and gel pill-brine interfaces.
In performing the test, the following procedure was used: first, the viscosified brine volume was placed in the test equipment. Normally, air bubbles must be removed. This was done by vibrating the experimental setup. Thereafter, the gel pill was placed on top of the brine. To place the gel pill, a custom-made hand pump with a volume of 1.5 L was used. Due to volumes of the workstring and the length of gel pill, refilling of the pump was necessary. When the gel pill was placed, a sponge pig was run to clean the pipe, which compressed the gel pill gently. The gel was left to rest for at least 30 min prior to placing the model drilling fluid on top of the gel pill. The gel placement was a pump and pull operation. Subsequently, the prepared amount of water base drilling fluid (WBDF) was placed on top of the gel pill and the remaining upper section of the setup filled with tap water. After some time, barite particles started to settle out. The pressure transducers and the cameras recorded the settling phenomenon and the performance of the gel pill. An example of the recorded pressure during placement of the different fluid and pill volumes is shown in Figure 8. Note that the zero values of the differential pressure transducers are arbitrary. Initially, for each test, the tubes to the measurement probes were air filled. Later in the tests, these tubes became partly liquid filled. Therefore, the absolute Energies 2020, 13, 6318 10 of 16 values of the differential pressure measurements are uncertain. However, all changes after placement of all the fluid volumes were measured accurately. Therefore, only the relative value changes were used from this time onward. min prior to placing the model drilling fluid on top of the gel pill. The gel placement was a pump and pull operation. Subsequently, the prepared amount of water base drilling fluid (WBDF) was placed on top of the gel pill and the remaining upper section of the setup filled with tap water. After some time, barite particles started to settle out. The pressure transducers and the cameras recorded the settling phenomenon and the performance of the gel pill. An example of the recorded pressure during placement of the different fluid and pill volumes is shown in Figure 8. Note that the zero values of the differential pressure transducers are arbitrary. Initially, for each test, the tubes to the measurement probes were air filled. Later in the tests, these tubes became partly liquid filled. Therefore, the absolute values of the differential pressure measurements are uncertain. However, all changes after placement of all the fluid volumes were measured accurately. Therefore, only the relative value changes were used from this time onward.

Gel Pill Performance in Vertical Hole
The experiment was conducted using the bentonite gel pill. Barite sag would occur in a static, vertical fluid column, the so-called static sag. Such a process is slow when the low shear viscosity is high, like in the present case. During the experiment, the concentration of barite particles should increase at the lower part of the tube filled with the model drilling fluid and decrease in the higher parts. By studying the pressure curves shown in Figure 9, the likely sag scenario is as follows. During the first two hours after placement of the drilling fluid volume, barite from the drilling fluid above the upper pressure sensor port sagged into the central parts of the drilling fluid column. Hence, the density increased and so did the pressure difference between the two upper measurement points. Thereafter, the density was reduced slowly. Twenty hours after placement of the drilling fluid volume, the pressure difference was back to the original. This required that some of the barite at that moment had been able to sag out of the column above the second pressure port of the pressure cell dP1. The pressure was anticipated to slowly decrease further until all barite was settled out.
The pressure readings from the dP2 differential pressure probe were constant during the first 20 h after placement of the drilling fluid. Any barite settled on the gel pill was not determined until the amount of settled barite was sufficient to either deform or move the gel pill. Most likely, the effect of sag in this part of the column was balanced by barite settling into the column and equal to the barite settling onto the gel.
In broad scale, the performance using the laponite pill ( Figure 10) was similar to that of the bentonite pill (Figure 9). Some sagging from the upper drilling fluid volume part was observed in the first two hours after placement of the drilling fluid as the dP1 values increased slightly. Then in the following period, more barite was sagging out of the measurement zone than into this zone.
No explanation can be verified for the increased drilling fluid density for the volume between the dP1 ports during the last 7 h. The pressure from the dP2 sensor showed reasonably constant values throughout the whole experiment. This indicates that the laponite pill retained its position throughout the total experimental time. The lack of movement of the gel pill was verified by the photographs showing the same position both before and after the 20 h static period, as shown in Figure 11.
respectively. The zero pressure is valid for the bottom hole pressure only (blue curve). For the dPsensors, the zero level is arbitrary.

Gel Pill Performance in Vertical Hole
The experiment was conducted using the bentonite gel pill. Barite sag would occur in a static, vertical fluid column, the so-called static sag. Such a process is slow when the low shear viscosity is high, like in the present case. During the experiment, the concentration of barite particles should increase at the lower part of the tube filled with the model drilling fluid and decrease in the higher parts. By studying the pressure curves shown in Figure 9, the likely sag scenario is as follows. During the first two hours after placement of the drilling fluid volume, barite from the drilling fluid above the upper pressure sensor port sagged into the central parts of the drilling fluid column. Hence, the density increased and so did the pressure difference between the two upper measurement points. Thereafter, the density was reduced slowly. Twenty hours after placement of the drilling fluid volume, the pressure difference was back to the original. This required that some of the barite at that moment had been able to sag out of the column above the second pressure port of the pressure cell dP1. The pressure was anticipated to slowly decrease further until all barite was settled out. The pressure readings from the dP2 differential pressure probe were constant during the first 20 h after placement of the drilling fluid. Any barite settled on the gel pill was not determined until the amount of settled barite was sufficient to either deform or move the gel pill. Most likely, the effect of sag in this part of the column was balanced by barite settling into the column and equal to the barite settling onto the gel. In broad scale, the performance using the laponite pill ( Figure 10) was similar to that of the bentonite pill ( Figure 9). Some sagging from the upper drilling fluid volume part was observed in the first two hours after placement of the drilling fluid as the dP1 values increased slightly. Then in the following period, more barite was sagging out of the measurement zone than into this zone. No explanation can be verified for the increased drilling fluid density for the volume between the dP1 ports during the last 7 h. The pressure from the dP2 sensor showed reasonably constant values throughout the whole experiment. This indicates that the laponite pill retained its position throughout the total experimental time. The lack of movement of the gel pill was verified by the photographs showing the same position both before and after the 20 h static period, as shown in Figure 11.

Gel Pill Performance in a 40 • Deviated Hole
The tendency of sag is stronger in deviated holes than in vertical holes because of the Boycott effect [5]. The barite sag direction is now also in the cross-sectional direction, creating density differences in the cross section. Hence, there is a density difference in the cross section that sets up a fluid circulation accelerating the sag. This is clearly seen in the gel pill experiments at a 40 • angle from vertical. The pressure measurements from the bentonite test are shown in Figure 12 and from the laponite test in Figure 13. In both tests, the dP1 sensor registered a significant reduction in pressure, indicating that barite was sagging out of the fluid column between the sensor ports. At the same time, the dP2 sensor measured less reduction in pressure than was measured using the dP1 sensor. This means that the weight of the sagged material falling onto the gel was unable to produce a force large enough to be transmitted to the bottom of the gel. This was also indicated by the lack of change in bottom hole pressure. A small reduction was measured. However, this was less than any of the pressure reductions measured by the dP1 or dP2 sensors. Hence, the gel was strong enough to withstand the change in pressure from the top.  Photos of the interfaces between the laponite gel and the drilling fluid or viscosified brine are shown in Figure 14. The photos were recorded just after placement and 24 h later. The positions of the interfaces remain unchanged, verifying the analysis of the results from the data shown in Figure 13.  Photos of the interfaces between the laponite gel and the drilling fluid or viscosified brine are shown in Figure 14. The photos were recorded just after placement and 24 h later. The positions of the interfaces remain unchanged, verifying the analysis of the results from the data shown in Figure 13.

Discussion and Remarks
So-called viscous pills have been used extensively in the petroleum industry to prevent intermixing of a dense well fluid placed above a lighter fluid. The success rate has varied. The industry has not had a proper definition of the term viscous pill. Hence, viscous pill has been used for a large variety of limited well fluid volumes pumped into a well. In this work, the term viscous pill has been defined as a high viscosity material without any significant gel formation. If gel formation has been significant, then the term gel pill has been used. Based on the measurement and analysis in the previous section, use of a purely viscous pill cannot hinder intermixing of a high density fluid placed above a lighter fluid. This should therefore not be applied in practical operations.
Two bentonite-type-based gel pill systems were found to be efficient in hindering intermixing of a denser fluid placed above a lighter fluid. These fluids create a good gel structure with bonding to the surface. The analysis did not focus on finding the limit of the yield stress or gel formation required to maintain the desired function. An analysis can be performed based on Equation (1), presenting the necessary gel strength. However, the gel strength measurements that can be obtained following industrial standards recommend methods incapable of measuring the strength of a gelled particle network.
Both the successful gel systems presented in this work are particle gels. Earlier, a crosslinked polymer gel system provided similar effect, as shown by Ronaes et al. [25]. In this case, the gel did not bond to hole walls. Hence, they transmitted pressure from the overlaying fluid column independent of the magnitude of the added pressure. For the current gel pill system, this transmission is not expected until a pressure difference given by Equation (1) is obtained. As can be seen from the measurements shown in Figure 12, there is a significant pressure reduction in the region measured using differential pressure transducer number two, which includes the pressure drop over the gel pill. This pressure reduction was not observed by using the bottom hole pressure sensor. Hence, the gel pill was anticipated to trap the down hole pressure until the pressure difference over the gel pill exceeded the maximum pressure it could hold. Then, the gel would move slightly and re-establish pressure control.
During the time of the experiments, the pressure measurements dP1 and dP2 both demonstrated reduction in the differential pressure, resulting from settling of barite. Barite settled onto the gel pill surface without creating any changes in the down hole pressure. In addition to trapping the pressure because of the gel forces, the weight of the settled barite must also be lifted before the gelled pill moves in any direction. It is not yet known how the pressure will change if the barite occupies the whole pipe volume. In this case, it may be possible that the settled barite transfers parts of its weight to the tubing.