Study of Floating Wind Turbine with Modified Tension Leg Platform Placed in Regular Waves

In this study, the typical ocean environment was simulated with the aim to investigate the dynamic response under various environmental conditions of a Tension Leg Platform (TLP) type floating offshore wind turbine system. By applying Froude scaling, a scale model with a scale of 1:200 was designed and model experiments were carried out in a lab-scale wave flume that generated regular periodic waves by means of a piston-type wave generator while a wave absorber dissipated wave energy on the other side of the channel. The model was designed and manufactured based on the standard prototype of the National Renewable Energy Laboratory (NREL) 5 MW offshore wind turbine. In the first half of the study, the motion and structural responses for operational wave conditions of the North Sea near Scotland were considered to investigate the performance of a traditional TLP floating wind turbine compared with that of a newly designed TLP with added mooring lines. The new mooring lines were attached with the objective of increasing the horizontal stiffness of the system and thereby reducing the dominant motion of the TLP platform (i.e., the surge motion). The results of surge translational motions were obtained both in the frequency domain, using the response amplitude operator (RAO), and in the time domain, using the omega arithmetic method for the relative velocity. The results obtained show that our suggested concept improves the stability of the platform and reduces the overall motion of the system in all degrees-of-freedom. Moreover, the modified design was verified to enable operation in extreme wave conditions based on real data for a 100-year return period of the Northern Sea of California. The loads applied by the waves on the structure were also measured experimentally using modified Morison equation—the formula most frequently used to estimate wave-induced forces on offshore floating structures. The corresponding results obtained show that the wave loads applied on the new design TLP had less amplitude than the initial model and confirmed the significant contribution of the mooring lines in improving the performance of the system.


Introduction
Offshore wind turbines generate more electricity than their onshore counterparts owing to higher wind speeds occasioned by the low surface roughness of the ocean.Due to increased interest in the design of offshore wind farms, the foundation of traditional fixed-bottom offshore wind turbines has been changing to the prolific floating type, which may be more feasible and less expensive for deep water.The diversity in the specifications of each floating platform type and the fact that wind turbines encounter a variety of wind, current, and wave loading at sea have resulted in active research into the dynamic response of offshore floating wind turbine support systems under various conditions with a view to ensuring security and reliability.
In this study, the design of the traditional TLP floating platform derived from the NREL prototype and a conceptual TLP design with additional mooring lines were experimentally investigated.The additional mooring lines reinforce the horizontal stiffness of the system and thereby diminish the dominant motion, which is obviously the surge motion, to enable safe performance in deep water.In the study, a series of experiments were conducted using a 1:200 scale model to determine the impact of waves on the performance of the model.The range of operational and extreme waves used in the experiments was based on real data for a 100-year return period of the Northern Sea of California to ensure the feasibility of installing the new system in the chosen site.Another objective of this study was determination of the wave loads on the platform; this was achieved experimentally using the Morison equation.
Previous studies predominantly focused on measurement of the wave loads acting on a fixed-bottom offshore wind turbine.Peeringa [22] showed that an acceptable prediction of the wave loads for non-breaking waves is achievable by using the Morison equation and the stream function wave model.However, the hydrodynamic forces are underestimated by the applied methods in the case of breaking and post-breaking waves.Journee and Massie [23] and Sarpkay and Isaacson [24] proposed various methods to define the drag and inertia coefficients for better estimation of the solution to the Morison equation.Burrows et al. [25] also defined several techniques, such as least square, cross-spectral, and the methods of moments, to identify these coefficients, and subsequently measured the wave loads using the Morison equation to prove the accuracy of predicting random forces using the equation.The measured data were later shown to sufficiently match the predicted values, which confirmed the suitability of the equation for measuring wave loads.Henderson [26] subsequently enumerated several methods to determine wave load models and structural dynamics models depending not only on the turbine selected but also the support structure.The studies conducted revealed that the selection of a relevant approach for defining the resulting loads plays a fundamental role in the cost of the structure and its ability to resist environmental loads.Dean and Dalrymple [27] presented several methods to define appropriate wave kinematics theoretically or experimentally.
Considering the results of the above studies, in this study, the Morison equation was applied to measure the wave loading on the offshore wind turbine's TLP platform to verify its accuracy in predicting the wave loading on an offshore floating structure.The remainder of this paper is organized as follows: Section 2 describes the experimental setup used to perform the experiments on the scale model.An enumeration of the main properties of the model along with the laws that permit scaling it down and a sketch of the new design are also given, and the difficulties and errors dealt with while performing the experiments outlined.Section 3 provides a theoretical outline of all the governing equations used in our study in order to facilitate a thorough understanding of the physics underlying the phenomena under investigation.Section 4 analyzes, discusses, and interprets the data collected in the experiments.The data are associated with both the dynamic performance of the two concepts in response to regular and extreme waves and also the wave loading on the structure.Finally, Section 5 concludes by summarizing all the results obtained and outlines plans for further work.

Design of the Laboratory Experiment
Considering the dimensional restrictions imposed by the wave flume, the scale of the model was set at λ m /λ p = 1:200.The subscript "m" denotes the scale of the model and "p" the scale of the prototype (see Figure 1).Froude scaling was applied in order to establish scaling factors between the model and the full-scale prototype (Jonkman et al. [1]).The latter was derived from the NREL 5 MW wind turbine.In the flume experiment, the piston-type wave maker was used to generate a propagating wave more effectively because the horizontal water particle velocities of the wave and paddle are nearly constant over the water column.In the flume, a passive wave absorbers comprised a hard filling material was installed in the channel.Based on the wave theory and reflectance, two wave gauges (KENEK, Wave height Meter CH-606) were used to take proper samples for a period, approximately 30 s (see more details in the papers of Lim [28] and Zhu and Lim [29]).To make reliable result, the experiment considered the effect of evanescent waves in the wave flume, which could contaminate test areas leading unexpected data.To avoid this effect, the model was placed around three times away from the wave maker.However, due to the size limitation of the wave flume, the influence of evanescent waves was not severe, but still remained (see Lim [28] and Zhu and Lim [29]).The model was made from acrylic plastic; the design parameters for all the various dimensions, which were scaled according to Froude law, are listed in Table 1.The shape was identical to that of the prototype and the model surface was smooth in order to prevent deterioration of the surface over time and model deformations.However, scaling all the parameters precisely was difficult to achieve because of the large scale chosen for our study and the fact that we were primarily interested in the hydrodynamic motion of the platform.For these reasons, the aerodynamic properties of the wind turbine were not scaled, which means that the blades, rotor, and nacelle were not taken into consideration and only the height of the tower along with the overall mass of both the tower and the rotor nacelle assembly were matched with the real wind turbine parameters for the 5 MW wind turbine specifications (see Jonkman et al. [1]).In addition, for the TLP model, as proven previously, the larger is the length scale, the more dominant will be the scale effects, and the more complicated it will be to obtain identical ratios between the model and its prototype.Thus, the model was scaled more to the perfect weight than the perfect length in such a manner as not to impair the scaling of the moment of inertia of the system, which is a parameter that is directly proportional to both the length and the weight.
The modified concept developed in this study was actualized by connecting additional mooring catenaries to the system (see Figure 2).The catenaries were directly attached to the platform in the bottom surface in order to increase the horizontal stiffness and give more stability to the system.As shown in Figure 2, the rigid body, comprising the wind turbine and the floating support, undergoes oscillatory translational and rotational motions as a result of wind and wave loadings.Surge and sway (ξ 1 and ξ 2 ) describe horizontal motions along the x and y axes, respectively.The horizontal axes of the system were aligned with the four spokes to which the floater tethers were connected.Heave (ξ 3 ) represents the vertical motion of the floater.The oscillatory angular motions are referred to as the roll, pitch, and yaw.The surge, sway, and yaw describe the three rigid-body motions.The tether lengths were assumed to remain constant during rigid-body motion.Figure 3 illustrates the configuration of the modified TLP with the added inclined lines.Four small holes were drilled in the bottom surface of the cylinder and filled with glue.The steel wire ropes, containing a soft spring at each line, were then introduced into the holes and glue applied to make it harden.The combination of spring and steel wire resulted in a non-homogeneous model for modeling the axial stiffness and neglecting the bending stiffness (Bartrop [30]).The scale model tests were then carried out in the wave flume of our laboratory.(see Table 2) On one side, the wave tank was fitted with a piston-type wave maker that generated regular monochromatic waves with different heights and periods.On the downstream section of the flume, a wave absorber was installed to dissipate wave energy and to avoid reflected waves inside the tank.The response of the TLP model to the wave loading was then studied through a sensor via a wireless data acquisition system, which eliminated the need for cables that would otherwise affect the platform motions and hence the experimental results.The sensor used in the experiments was placed inside the cylinder of the model's platform; it facilitated the measurement of six degrees-of-freedom deviations simultaneously.The waves generated by the wave maker were recorded using the wave gauge placed upstream of the model, and the depth of water in the flume was kept constant.The order of the test wave amplitudes was varied from 0 to 40 mm with a test wave period from 0.4 to 2 s.The experimental data were recorded and controlled using National Instruments LabVIEW software.

Equation of Motion
An offshore wind turbine mounted on a TLP undergoes six degrees-of-freedom motion forming three rigid body translational motions and three rotational motions.When it is excited by waves, the assumption based on the linear hydrodynamic analysis and a linear damping allows the motion equations for surge, heave, pitch, and yaw to be solved in the frequency domain.Sway and roll are identical to surge and pitch, thus are not treated here.It was also assumed that no waves are generated by the floater, since the wavelengths of the ambient waves were assumed to be much greater than the floater diameter.The wave-floater interaction problem can therefore be solved in a simplified manner.The governing equation describing the balancing of the exciting forces for the surge behavior is derived from Newton's second law (see Withee [6]), and is stated as follows: and the uncoupled heave and yaw equations of motion are: where M jk are the components of the mass matrix of the system; B jk and A jk are the frequency-dependent damping and added mass coefficients, respectively; F j are the external exciting forces due to waves; and C jk are the hydrostatic restoring coefficients.The term ξ represents the dimensional acceleration of the system in each mode of motion at each frequency, ξ is the system's velocity in each mode, and ξ is the system's displacement.The solution to these coefficients is fundamental for solving the equation of motion; a solution procedure was described in detail by Withee [6], with the assumption that the restoring is achieved by a stiff mooring tether that limits any significant motion in pitch and drives the restoring in pitch toward infinity (Wayman and Sclavonous [2]).The eigenvalues of this equation give the natural frequencies for the modes of motion in this study.
In order for the system to be analyzed using linear frequency domain analysis, all of the linear quantities must be analyzed relative to the wave elevation: where A is the wave amplitude.The linear wave excitation forces f i acting on the platform are defined relative to the local coordinate system (x, y, z) and by virtue of linearity adopt the complex representation: where X i is the complex amplitude of the exciting force or moment in the i-direction.The platform motions ξ i in the six degrees of freedom also adopt the complex representation: where Ξ i is the complex response amplitude for the platform in the j-direction (i.e., RAO).The water particle components are essential in defining the wave-induced forces on floating structures.Therefore, the Airy wave theory, often called the linear wave theory, was used to predict the horizontal water velocity and acceleration where the cylinder is located (Dean and Dalrymple [27]).

Modified Morison Equation
In deep water, the waves are assumed to have a low steepness (small wave height compared to wavelength).This enabled us to use the Airy linear wave theory.This latter assumption and the assumption that the waves are unidirectional are considered basic assumptions for the use of the Morison equation for calculating the wave loading on offshore structures.
A simple equation was developed by Morison for calculating the wave loads on floating submerged structures in water.The equation is stated as follows: where dF is total wave force; U and U are fluid velocity and acceleration, respectively; V and V are the relative velocity and acceleration of the floating structure; C a and C D are the added-mass and drag coefficient; ρ is density; and D is the cylinder diameter.The first two terms on the right side of the equation represent the inertia forces, while the last term determines the drag forces on the platform.The inertia forces comprise the Froude-Krylov force and the hydrodynamic mass force.

Results and Analysis
The scale floating wind turbine model was experimentally tested against a series of regular waves generated by the wave maker to obtain the dynamic response of the system in the six degrees of freedom.Regular wave parameters were chosen based on historical wave data for the North Sea near Scotland, where it was assumed that the offshore TLP wind turbine will operate.

Surge Dynamic Analysis of the TLP in Response to Regular Wave
All the physical structures including the floaters displayed natural frequencies in their motion.It is well known that a structure tends to oscillate at this frequency when stimulated by external forces.Under resonance conditions, a small force applied at this frequency produces a large oscillatory response.Thus, a dynamic force applied to a physical object causes it to vibrate.It is therefore important to know, on the one hand, the natural frequencies within a system and, on the other hand, the frequencies at which excitation is likely to occur to ensure that they do not coincide.It is generally not possible to control excitation frequencies of excitation, but the natural frequency of a system-which depends on physical characteristics such as mass and stiffness-can be altered.
When the TLP model is subjected to regular waves, the mooring lines may help to reduce the rotational motion around the three axes, even though they were mainly designed to reduce the surge acceleration and displacement.Incoming regular waves were assumed to be uniform and incident on the platform in the surge direction and a wave with an amplitude of approximately 12 mm and a wave period of T = 0.8 s was chosen for this experiment.Figure 4 shows the temporal variation of surge acceleration for the initial TLP and modified TLP concepts, while the corresponding surge amplitude spectrum comparison of the initial and modified concepts after applying Fast Fourier Transform (FFT) to the signal's temporal variation is given in Figure 5.As shown in Figures 4 and 5, the amplitude of the surge acceleration decreased as a result of addition of the mooring lines.This indicates that the new configuration contributes significantly to enable effective damping of the surge motion compared to the vertical tendons only, and hence improves the performance of the platform under wave attack.In addition, the spectra display well-defined peaks because of the periodic harmonic motion displayed in the time domain, even though the spectrum of the initial model appears to be noisier than that of the modified TLP for the same wave frequency.There are a couple of reasons to explain the improvement.One would be larger amplitude motion in the initial model, and the other an additional mooring line in modified TLP configuration; nevertheless, the peaks remain well defined in both cases.These findings confirm that the modified concept helps to stabilize the system's motion, which is essential to improving the performance of the wind turbine, because reducing the motion positively affects power production and turbine structural loading.In other words, platform motion causes larger inertial loads on the entire structure, which potentially leads to reduced efficiency and increased fatigue loading.Furthermore, the tether pretension also plays a fundamental role in the stability of the system.This also explains why the modified TLP with its higher initial pretension is more stable than the initial four-legged TLP.The new tethers were inclined, instead of being straight, in order that they not exceed the operational range of the tether's pretension.

RAO Analysis for Regular Wave Tests
In this study, the water depth was kept constant at 35 cm in the wave flume, and a series of regular wave tests was carried out on both the initial model and the new design.This was done to validate previous results and to study the natural period and natural frequency of the new model compared to the initial one using the RAO method.The RAO is defined as the non-dimensional ratio of the surge to the surface elevation, which is used to analyze the dynamic motion of floating structures.
Figure 6 shows the RAOs for the NREL TLP, the modified TLP, and a numerical simulation of the same prototype (i.e., modified TLP) developed by Nematbakhsh [31].For the translational accelerations (surge, sway, and heave), the RAO is determined by where S R ( f ) represents the dimensional response of the structure in each mode of motion in the frequency domain and S I ( f ) is the wave power spectral density.As shown in the figure, both the initial TLP and the new design have the same trend with a slight decrease in the surge RAO response.However, the natural frequency, defined graphically as the frequency at which the peak occurs, was slightly shifted to a higher frequency for the new design but remained smaller than 0.4 rad/s.In addition, it was considered as the operational natural wave condition for FOWT, which is defined by ITTC spectrum for different sea states and provides a significant wave height of 5.0 m and a modal period of 12.4 s (see Kim and Hong [32]).On top of this condition, the water flume was only operated by a wave generator so that it was purely affected by the wave loading because wind tunnel was not turned on.On the other hand, the reference data of numerical simulation were also based on the nonlinear hydrodynamic forces on the platform, while wind speed was assumed constant.Therefore, the natural frequency can be inferred from the surge RAO response of the test model itself exerted by the wave loading.Consequently, both concepts can operate safely in the chosen site.Furthermore, to validate the results, the experimental surge RAO data were compared to the numerical representation.This latter was performed for a range of wave periods, from 0.6 to 1.2 s.
The results obtained show that, for the same range of wave frequencies, a good similarity was found between the numerical and experimental data as the RAO motion increases while moving close to the natural frequency.It was expected that the peak in the numerical model would occur within the same range of wave frequency since the natural frequency in surge was defined to be 15 s.

Water Depth Effect
Considering that offshore wind turbines are suited to operate in rated power case as well as in deep water, the effect of water depth was investigated and experiments conducted to ensure the capability of the modified concept TLP to operate in deep water.Figure 7 compares the surge RAO's response in two different water depths for the TLP with the additional cables.
As shown in Figure 7, the RAO shows that the motion of the platform decreases with increasing water depth, which confirms that the TLP is a suitable structure for deep water.On the other hand, the natural frequency of the system was shifted to lower frequency in the case of the TLP with additional mooring cables in greater water depth.This was achieved as a result of the increase in the length of the tendons and the added mooring lines when operating in deeper water.The increase in the length of the tethers and the added mooring lines influenced the amplitude motion as well as the natural frequency, and they enabled an acceptable restoration in the surge of the system reducing the natural frequency.The same results were obtained by Wayman and Sclavonous [2], who investigated the water depth effect for an NREL TLP.Those results and the results of this actual study are in good agreement as both studies indicate that the water depth not only contributes to reduce the motion but also lowers the natural frequency.Thus, it is possible to tune the tether stiffness of a system to match a certain experimental natural frequency by means of restoring.

Wave Loading Using Morison Equation for Regular Waves
The wave loads were calculated using the Morison equation.The experimental values obtained for the initial TLP were then compared to those for the TLP with the additional cables.The experimental conditions were similar for both cases and the same wave height and wave period were applied in the case of a regular wave test.

Omega Arithmetic Method for Relative Velocity
One of the requirements of the Morison equation for predicting wave loading in floating structures is the definition of the relative velocity of the system while being subjected to the action of the incoming waves.The relative velocity was integrated from the acceleration data using the omega arithmetic method, which is considered to be the best method for the integration to convert acceleration into velocity (see Appendix A for omega arithmetic code).
As shown in Figure 8, the relative velocity is represented after being integrated from the acceleration data using the omega arithmetic method outlined above.The method determines the corresponding velocity from an acceleration dataset without going through the formal integration in time.Meanwhile, this method is obviously influenced by the frequency behavior of the signal, as the conversion process was carried out in the frequency domain rather the time domain signal.In other words, the time series were converted to the frequency domain using FFT, integrated by dividing by ω, and then converted back to the time domain using the inverse FFT.Thus, this procedure is the most accurate for the conversion process because neither the time domain integration nor the application of a high pass filter before performing the integration was a good solution for integrating the relative velocity in this case.
Because the acceleration motion response is a harmonic function, the velocity has a sinusoidal variation, but it is not in phase.The phase relationship between acceleration and velocity is such that the velocity is 90 • out of phase with acceleration.This is noticeable from the figures; when the structure passed through the equilibrium position, the velocity was at its maximum and the acceleration was zero. Figure 9 compares the relative velocity of the TLP with tendons only and the modified concept with additional mooring lines attached.It shows that the magnitude of the velocity was smaller in the new model than in the prototype.The results confirm the findings that the mooring lines helped to reduce not only the surge acceleration but also the velocity of the structure when it was subjected to monochromatic regular waves.

Wave Loading Results
The water particle kinematics in the case of a regular wave can be defined on the basis of the extrapolated Airy wave theory.The Airy theory was used because of its suitability for a wide range of waves at any site, including extreme and fatigue cases.However, it has a drawback in that it does not consider the peaks and troughs of waves.Conversely, the extrapolated Airy theory, known as the wheeler stretching method, makes the original theory more flexible by calculating the kinematics both at the mean water level and at the water elevation surface, which results in a kinematics prediction that is closer to reality.
Numerous methods also exist for defining the inertia and drag coefficients.The results published by the DNV (Det Norske Veritas) are widely accepted (Journee and Massie [23]).The DNV has calculated coefficients for different types of cylinders based on their roughness with respect to the KC (Keulegan-Carpenter) number because of the primary dependence of the coefficients on the number.The KC number is expressed by the following equation (which is valid for the deep-water studies): where U is the water particle velocity, T is the wave period, D is the cylinder diameter, and H is the wave height.Based on the DNV report, the inertia coefficient of a smooth floating cylindrical platform is related to the added mass coefficient by the following relation: where C a = 1 in the case of a circular cylinder.This leads to an inertia coefficient with an approximate value of two and a drag coefficient close to one for low KC numbers, as is the case in this study where the inertia forces are dominant and the drag forces are not important.In this study, to get both coefficients, the Morison's method was applied (see Journee and Massie [23]).This method is based on the measured force (N), velocity (m/s) and acceleration (m/s 2 ) from the flume experiment.Given that the fundamental data were provided, the Morison equation can be decomposed into two parts: inertia and drag terms.Therefore, based on the Morison's method, the drag coefficient can be obtained while making the relative acceleration becomes zero, whereas the inertia coefficients can also be calculated while having relative velocity zero.More details are also well described in the paper (see Wolfram and Naghipour [33]).
From the results for operational range, it is clear that the forces caused by the interaction between the cylinder and the waves on the new design are less than those on the initial model (see Figure 10).This confirms that the new mooring lines not only contribute to a stable system but also results in lower load on the platform.Moreover, the horizontal component of the total force per unit length has a harmonic shape because of the accelerating and decelerating movements in the body motion, which imply a change in the kinetic energy of the fluid within the control volume.Furthermore, the unstable drag and inertia coefficients also have an effect on the forces as they depend primarily on the KC number, which in turn depends on the velocity of the fluid.As a result, the better estimation of the water kinematics enabled the Morison equation to be more accurate in predicting the wave loading on the TLP's cylinder.It is also notable that the loads have a nonzero mean value.This offset may be explained by the excess buoyancy and the pretension on the tether, which requires that the cylinder support some of the load in order to keep the system sufficiently balanced.This is because the pretension of the tethers is related to the buoyancy force and the overall mass of the system times the gravitational acceleration.

Extreme Design Sea Condition Analysis
The ability of the new system with added mooring lines to withstand extreme sea conditions in Northern sea of California was verified.This verification was performed with the objective of ensuring that the new design can operate in a severe sea state, which makes it suitable for both regular and extreme sea states.The extreme sea conditions were issued by the Center for Offshore Safety, USA, and the parameters of the waves were chosen based on their report (Berg [34]).The chosen wave amplitude was 5 cm with a wave period of 1.2 s based on the scale ratio of 1:200 used in this study.
As shown in Figures 11 and 12, the surge acceleration remained the most obvious of the three translational motions with a larger amplitude than regular waves because of the severe sea state.However, the extreme design case caused the platform to have significant motion in the sway direction, which cannot be neglected as in the case of the regular wave, because of the substantial contribution of the mooring lines in effectively damping all the other rigid body and rotational motions.In addition, the ability of the system to respond was demonstrated and it was also shown that severe wave conditions tend to increase the motion amplitude of the modified TLP above the regular and operational range.However, this amplitude remained in the acceptable range where a structure can ensure its operability without affecting the performance of the installed wind turbine.As shown in Figure 13, the surge amplitude spectra derived from the time domain using the FFT, which defines a comparison between the surge acceleration in the extreme conditions of the two concepts, confirmed the mooring lines contribution in damping the surge motion even in extreme conditions.However, because the exhibited motion had a larger amplitude, the spectra appeared noisier than in the regular case, but the peaks were still well defined.Another aspect of concern is the loads applied to the structure in the extreme wave event.It was expected that the wave would have a significant impact on the structure in terms of loading, as it was proven that the added mass generated in the case of an extreme wave is higher owing to the high kinetic energy of the fluid around the structure, which causes an increase in both the body's motion and the water kinematics.Therefore, the loading on the system exerted a high tension on the tethers and the new mooring lines; however, this tension should remain within the safe range because an excess on the design value would result in the consequent destruction of the system.This means that the new model withstood the extreme design wave condition for a 100-year return period for the chosen site.The new findings in the behavior of the modified TLP under the onslaught of waves may play a fundamental role in providing better stability and thereby improve the overall performance of the system, especially in critical environmental loads.This is because the mooring lines tend to increase the stiffness, which contributes to the rigidity of the system, and the design life of offshore wind turbines may be enhanced as well.

Conclusions
A new tension leg platform conceptual design for offshore wind turbines was proposed with the objective of reducing the dominant surge motion of this kind of platform.The feasibility of the new model to operate under different wave conditions was also investigated.The design was proposed based on the NREL prototype and the wave conditions were chosen according to a report in the USA regarding the Northern Sea of California, where it is assumed that the new system will operate.
For the operational range of regular waves, the following can be stated: • The modified concept model tends to decrease the velocity and acceleration of the overall system.A new method, known as the omega arithmetic method, which provides accurate and exact conversions, was introduced to integrate the displacement from the acceleration data.

•
The RAO surge response proved that the two concepts avoid the natural wave frequency.This means that resonance is avoided, which is one of the main requirements for FOWT in order to operate in a safe environment.Furthermore, the water depth also has the same effect as the mooring lines, as it was proven that the motion amplitudes decrease with increasing water depth, which confirms that the new model is suitable for deep water.

•
As regards extreme sea conditions for a return period of 100 years, the experimental results indicate that the motion amplitude will increase without exceeding the range of accelerations where the floating system is known to be able to operate safely.Further, the modified concept was verified to have smaller motion amplitude than the initial concept even in harsh environmental conditions.

•
The loads applied on the structure by the waves were also measured using the Morison equation after matching all the conditions required for the use of the equation.

•
The results obtained for the new model show that the addition of the mooring lines plays a positive role in reducing the wave loads compared to the initial model in the case of both regular and extreme waves.
These findings on the performance of the model under wave effect should be taken into account when constructing this kind of platform in the future.However, additional studies need to be conducted in order to investigate the coupled dynamic motion under all combined environmental loads combined with the tension on the tethers to enable optimization of the modified TLP system with additional lines.This would further improve the modified concept TLP system and help to effectively minimize the drawbacks to withstanding all environmental loads and increase the performance of offshore wind turbines.On top of these findings, the scaling issue would be one of the important considerations when the test data of scaled model match the full scale model.In particular, most measurements in the flume ertr made only on a small-scale model, which needs further investigation in the future.

Figure 4 .
Figure 4. Time domain surge acceleration comparison for new and initial TLP concept.

Figure 5 .
Figure 5. Surge spectrum for initial and modified TLP concept.

Figure 6 .
Figure 6.The surge RAO comparison for the two concepts.

Figure 7 .
Figure 7.The water depth effect on the motion of the modified TLP with cables.

Figure 8 .
Figure 8.The time domain for surge acceleration and velocity of the initial TLP.

Figure 9 .
Figure 9.Time domain surge velocity comparison for new and initial TLP concept.

Figure 10 .
Figure 10.Experimental wave loads comparison in a regular wave.

Figure 11 .
Figure 11.Translational accelerations in extreme design condition for modified TLP.

Figure 12 .
Figure 12.Surge acceleration comparison for both concepts in extreme design case.

Figure 13 .
Figure 13.Initial and modified TLP's surge spectrum in extreme case.

Table 1 .
Main design parameters of the Tension-Leg Platform (TLP) model.

Table 2 .
Spoke and mooring lines design parameters.