Planning of the Multi-Energy Circular System Coupled with Waste Processing Base: A Case from China

: With the accelerated development of urbanization, waste disposal has become a tough problem. If waste cannot be disposed properly, it will lead to environment pollution and waste of resources. Since the energy utilization of the Waste Processing Base (WPB) has not been considered thoroughly, optimal planning of the Multi-Energy Circular System (MECS) coupled with the WPB is studied in this paper. Based on a typical WPB, this paper adds Power to Gas (P2G) and energy storage equipment, and applies a bi-level optimization model to optimize energy utilization. The minimum of total annual cost is the objective of the upper model, whose decision variables are the capacity of each equipment. The minimum annual operating cost is the lower model’s objective whose decision variables are the control parameters of certain energy equipment. Finally, a practical WPB is used for the demonstration and simulation of the proposed planning scheme. The analysis of the simulation results indicates that the collaborative optimization of the MECS coupled with WPB is e ﬀ ective, and improves the beneﬁts of energy, economy, and environment enormously.


Introduction
Nowadays, energy, economy, and environment issues are becoming increasingly complicated, which attracts the general attention of governments around the world [1][2][3][4][5][6]. The traditional waste disposal methods applied most are landfill and incineration, which have been conducted in waste incineration power plants in Denmark and landfill in China. The existing energy utilization methods in a waste processing base (WPB) are relatively simple and not comprehensive, leading to the waste of energy and secondary pollution [7,8]. Therefore, collaborative planning of a multi-energy circular system (MECS) and WPB is essential to achieve coordinated energy utilization and find effective solutions to environmental issues.
The integration and collaboration of different energies in an integrated energy system can effectively improve the utilization of energy [9][10][11][12][13][14][15]. A generalized multi-energy system refers to a large-scale system composed of the development, conversion, transportation, scheduling, and other manipulations of a variety of energies, including coal [16], natural gas [17], water [18], wind [19], solar energy [20], and other forms of energy [21]. It is called a multi-energy system [22] for different kinds sources included in the system. The specific construction process of the physical planning architecture is shown in Figure 1. The physical planning architecture is divided into the supply side, the conversion side, the transport side, the energy storage side, and the load side. Based on the analysis of the environment, energy, and load factors of the multi-energy system, the impact of factor analysis on the planning architecture is figured out. Environmental factors are mainly related to the generation and conversion of energy, so the components on the supply side and the conversion side are affected. The energy factor involves the entire process of energy generation, conversion, transportation, and storage, so it affects all but the load side. The load factor is the last loop in the entire architecture, which can be traced back to every part of the architecture, so the load factor affects the entire physical planning architecture. Physical planning topology can be designed based on the factor analysis.
Energies 2018, 11, x FOR PEER REVIEW 3 of 17 the conversion side, the transport side, the energy storage side, and the load side. Based on the analysis of the environment, energy, and load factors of the multi-energy system, the impact of factor analysis on the planning architecture is figured out. Environmental factors are mainly related to the generation and conversion of energy, so the components on the supply side and the conversion side are affected. The energy factor involves the entire process of energy generation, conversion, transportation, and storage, so it affects all but the load side. The load factor is the last loop in the entire architecture, which can be traced back to every part of the architecture, so the load factor affects the entire physical planning architecture. Physical planning topology can be designed based on the factor analysis.  Figure 2 shows the physical planning architecture of a multi-energy system. It reveals the connection mode of the energy flow in the system. The energy equipment on the supply side and conversion side is divided into typical energy components and unique energy components. The operating status of multi-energy systems can be divided into two types: Islands and grid-connected. In China's current energy network, only the electricity and natural gas networks form a large-scale coverage. Therefore, in the physical planning framework, the external network of multi-energy systems only shows the interaction of electricity and gas network. It should be noted that only the supply side, conversion side, load side, energy storage side, and the transport side are collectively represented in the energy flow relationship, and it is not indicated that these elements are geographically aggregated inside the system.   Figure 2 shows the physical planning architecture of a multi-energy system. It reveals the connection mode of the energy flow in the system. The energy equipment on the supply side and conversion side is divided into typical energy components and unique energy components. The operating status of multi-energy systems can be divided into two types: Islands and grid-connected. In China's current energy network, only the electricity and natural gas networks form a large-scale coverage. Therefore, in the physical planning framework, the external network of multi-energy systems only shows the interaction of electricity and gas network. It should be noted that only the supply side, conversion side, load side, energy storage side, and the transport side are collectively represented in the energy flow relationship, and it is not indicated that these elements are geographically aggregated inside the system. the conversion side, the transport side, the energy storage side, and the load side. Based on the analysis of the environment, energy, and load factors of the multi-energy system, the impact of factor analysis on the planning architecture is figured out. Environmental factors are mainly related to the generation and conversion of energy, so the components on the supply side and the conversion side are affected. The energy factor involves the entire process of energy generation, conversion, transportation, and storage, so it affects all but the load side. The load factor is the last loop in the entire architecture, which can be traced back to every part of the architecture, so the load factor affects the entire physical planning architecture. Physical planning topology can be designed based on the factor analysis.  Figure 2 shows the physical planning architecture of a multi-energy system. It reveals the connection mode of the energy flow in the system. The energy equipment on the supply side and conversion side is divided into typical energy components and unique energy components. The operating status of multi-energy systems can be divided into two types: Islands and grid-connected. In China's current energy network, only the electricity and natural gas networks form a large-scale coverage. Therefore, in the physical planning framework, the external network of multi-energy systems only shows the interaction of electricity and gas network. It should be noted that only the supply side, conversion side, load side, energy storage side, and the transport side are collectively represented in the energy flow relationship, and it is not indicated that these elements are geographically aggregated inside the system.  Figure 2. Physical planning topology of park-level energy regional network.

Models of Equipment in MES
Energy equipment in a multi-energy system can be divided into typical energy equipment and unique equipment. Typical energy equipment can be divided into energy supply, energy conversion, energy storage, and energy transmission equipment. As supplement and promotion, the actual multi-energy system has its own unique energy equipment.

Typical Energy Equipment
(1) Energy supply equipment The energy supply equipment refers to the device that the input is a primary energy source, such as wind, photovoltaics, natural gas, etc., while the output is energy that can be directly used, such as electricity and heat. In the case of natural gas as a user load, it is generally converted to heat for use, so natural gas is not considered as a terminal energy source. The typical models in this section mainly cover wind power, photovoltaic power generation, gas boilers, gas turbines, and fuel cells. Due to space limitations, these models are not described here.
(2) Energy conversion equipment Through the energy conversion equipment, secondary energy sources such as electricity, heat, and cold can be flexibly converted between each other. There are heat pumps for electric-thermal conversion, electric refrigerators for electric cooling, heat exchangers for heat-to-heat conversion, and absorption refrigeration for heat-cooling conversion. These models are not described here. In addition, the development of power-to-gas (P2G) technology has enabled energy to achieve electric-gas transition [38]. Therefore, this section considers it as a special energy conversion element.
Electricity can be converted into CH 4 through P2G [39] V out P2G = η P2G P in

P2G
(1) where P in P2G is the input power in kWh, η P2G is the conversion efficiency of P2G, and V out P2G is the output volume of CH 4 in m 3 .
P2G is mainly subject to its rated power [39].
where P rated P2G stands for the rated power of P2G.

(3) Energy storage equipment
The energy storage component can realize the energy transfer on the time scale by storing the energy, and can improve the stability and flexibility of the energy supply in the system. In addition to suppressing the volatility of renewable energy, electricity storage can also achieve the goal of peak load shifting. Heat/cold storage can be used to cope with the complex and variable load. Gas storage can be used as an indirect solution for electricity storage, thereby reducing its storage cost.
Assuming that the energy storage and discharge power are constant during the time period ∆t, The energy relationship before and after discharge is as follows [40]: where W(t − ∆t) and W(t) are energy stored in power/heat/gas storage equipment before and after energy storage or discharge. Q c and Q d are capacities of energy stored or released. η c and η d are energy storage and dissipation efficiency. The following constraints must be met to ensure the stable operation of the equipment [40]: where W max and W min stand for the maximum and minimum value of stored energy. Q c,max and Q d,max are the maximum value of energy storage and discharge.
In order to reserve a certain amount of adjustment margin, the energy charged of the storage equipment after one cycle is restored to the original values of storage [40], that is where W 0 and W T are the power/heat/gas storage volume at the beginning and end.
(4) Energy transmission equipment Ignoring the transmission speed of the energy itself, the transmission characteristics of the electricity cables, heat/cold, and gas pipelines are basically similar, and the expressions are as follows [41]:

Unique Energy Equipment
WPB is taken as an example for explanation. The unique energy components of a WPB include waste incineration power plants, landfills, leachate treatment plants, biogas power plants, and biogas compression and purification stations.
(1) Waste incineration (WI) power plant The waste incineration power generation refers to power generation by burning urban waste. In the process of waste incineration, a large amount of heat is generated. At the same time, the waste incineration plant will also produce leachate. The model of the WI is shown as follows [42,43]: where P WI and Q WI respectively stand for the amount of power and waste heat generation in kWh, while M WI leachate and M WI waste are the amount of leachate produced and waste incineration in t. k P and k Q are the generation productiveness of power and heat in kWh/t, while k leachate is the leachate production rate of unit waste incineration.
(2) Waste landfill (WL) Landfill is a centralized dumping site of waste. The landfill product has two parts; one is landfill gas [44] that can be used as fuel, and the other is leachate [45], which is recycled to the leachate plant for reproduction. The more common model is as (10) and (11) shows.
In (10), V WL tgas , m, k, and T stand for the biogas production rate in year t, the amount of annual waste landfill, the attenuation coefficient, and total operating years of the landfill. W is the amount of wet garbage in landfill. ω is the moisture content of wet garbage, and V 0 is the production of biogas in unit dry garbage, theoretically.
where k WL lea is the leachate production rate of unit waste incineration, and V WL tlea is the volume of leachate produced.

(3) Leachate treatment (LT) plant
Biogas is obtained in LT. Leachate consumes electrical and thermal energy during processing and produces biogas. The model of LT [46] is as follows: where M LT leachate is the amount of the leachate treated in t, V LT gas is the biogas obtained in m 3 , P LT and Q LT stand for electricity and heat consumption, and γ gas is the biogas production rate, while γ P and γ Q are the power and heat consumption rate.
Part of the biogas generated by WL and LT is used for biogas power generation, and the other part for compression and purification.

(4) Biogas power plant (BP)
Biogas power generation technology is a new energy-comprehensive utilization technology that integrates environmental protection and energy conservation. The biogas generated by the anaerobic fermentation process enables the biogas generator to generate electricity [47].
where E is the total biogas generated by WL and LT, P BP is the electricity generated in kWh, k BP is the amount of power generated by unit volume of biogas in kWh/m 3 , and β 1 stands for the rate of biogas used for generation.

(5) Biogas compression and purification (BCP) plant
Purification of biogas refers to the removal of gases other than CH 4 in biogas [48].
where V BCP CH 4 is the amount of CH 4 after compression and purification in m 3 , and k BCP is the amount of CH 4 generated by unit volume of biogas via compression and purification.

Optimization Model of MECS Coupled with WPB
Annual operating costs are included in the planning objectives of the whole system [49,50]. The annual operating cost is mainly calculated by the optimal output of each equipment on a typical day as well as considering environmental benefits. However, the multi-energy (electricity/heat/gas) collaborative optimization of the system must be based on the installation capacity of each device. The two abovementioned mutually constrained and repeated iterations are needed to acquire the optimal planning scheme. Therefore, a bi-level planning model is applied to the system. The upper model deals with the investment decision problem, with the minimum annual cost as the target. The optimization variables are the installation capacity of each device. The lower model solves the operation optimization problem, with the goal of minimum annual operating costs (such as maintenance costs and carbon tax). The optimization variables are the dispatch value of each device in the system in time t. The investment results in the upper model affect the objective function and constraints in the lower. In return, the lower model takes the optimal value as feedback to the upper model, achieving the interaction between the upper and lower model. Energy balance, operational constraints, and optimization variable constraints are included in the optimization model. The minimum total annual cost is the objective of the upper model. The annual cost covers the investment in equipment C inv , annual operating costs C ope (calculated by Equation (20) in the lower model), waste disposal subsidies, and the environmental maintenance costs C ep for ecological construction after the closure of WL. The objective function [49] is shown below.
where α i is the discount rate for the investment expense of ith equipment, E i cap is the investment cost of the unit capacity in the ith equipment, and W i is the capacity of the ith equipment.
where β is the discount rate for environmental maintenance costs, and W WL stands for the landfill capacity. E ep 0 is the annual environmental maintenance cost of unit capacity, and T e is the environmental maintenance period of landfill.
where m t is the amount of waste treatment in time t, and A waste o is subsidy of per unit waste treatment.
(2) Constraints Considering the physical meaning of the optimization variables and the actual situation, the optimization variables need to be kept within a certain range [50].
where M waste is the amount of waste disposal per day, and V veh CH 4 is the volume of CH 4 vehicles used.

The Lower Model
(1) Objective function The lower-level planning model targets the minimum annual operating cost of the system. The annual operating cost of the system is made up of equipment operation and maintenance cost C man , energy benefit C ene , and environmental cost C CO 2 (mainly considering carbon tax).
where Q t,i is the output electricity/heat/gas energy of ith equipment in time t, and E man i is the operation and maintenance costs incurred by per unit energy of the ith equipment.
where P t , V t , and H t respectively stand for the sold electricity/heat/gas in time t. ω elec t , ω gas t , and ω heat t respectively stand for the electricity/heat/gas price in time t.
where ω tax is the carbon price, and λ V2G , λ GasP , and λ WI respectively stand for the carbon dioxide emissions of per unit fuel of car and boat, BP and WI. V Equipment operating constraints are mainly equipment rated power or rated capacity limit, just as Equations (4)- (7) show. Energy balance constraints include system power, thermal energy, and gas network. Moreover, the constraints of decision variables are also given in Equations (28)- (30).
where P sale , V sale , and Q sale refer to the capacity of power/heat/gas for sale. λ 1 , λ 2 , and β 1 are the dispatch ratio of WL, WI, and BP.

Solution Algorithm
In this paper, the bi-level programming model is solved by the genetic algorithm (upper model) and linear programming (lower model). The process of the algorithm solution is shown in Figure 3. The genetic algorithm is used for the upper model to search for the optimum solution through iteration. In each iteration process, it updates the capacities of components, and thus, the minimum operation cost can be calculated by the lower model. Then, the annual cost can be figured out. After selection, crossover, and mutation, new capacities are obtained. When the iteration is finished, this algorithm will find the optimum capacities as well as the operation mode of the components.  Figure 4 shows the overview of the original WPB. It is located at the seaside and has abundant wind energy resources. The WPB is a self-sufficient energy park. The external resources required in the base are only waste, and it can produce biogas, natural gas, and other energy sources from landfilling, leachate, and incineration. However, the original equipment does not fully reflect the complementary energy characteristics, resulting in low energy utilization. For example, the thermal energy of the power plant is not used, and the biogas of the leachate plant is directly burned and discharged. In addition, the serious wind abandonment phenomenon in the WPB is also an important reason for low energy utilization.

Case Analysis
In this section, a practical WPB in Shanghai is selected as the case scenario. This paper focuses on a practical WPB and expands the intrinsic equipment, constructing a multi-energy complementary device on the basis of it. A MECS in which the WPB acts as the core is formed. Figure 4 shows the overview of the original WPB. It is located at the seaside and has abundant wind energy resources. The WPB is a self-sufficient energy park. The external resources required in the base are only waste, and it can produce biogas, natural gas, and other energy sources from landfilling, leachate, and incineration. However, the original equipment does not fully reflect the complementary energy characteristics, resulting in low energy utilization. For example, the thermal energy of the power plant is not used, and the biogas of the leachate plant is directly burned and discharged. In addition, the serious wind abandonment phenomenon in the WPB is also an important reason for low energy utilization.   Figure 4 shows the overview of the original WPB. It is located at the seaside and has abundant wind energy resources. The WPB is a self-sufficient energy park. The external resources required in the base are only waste, and it can produce biogas, natural gas, and other energy sources from landfilling, leachate, and incineration. However, the original equipment does not fully reflect the complementary energy characteristics, resulting in low energy utilization. For example, the thermal energy of the power plant is not used, and the biogas of the leachate plant is directly burned and discharged. In addition, the serious wind abandonment phenomenon in the WPB is also an important reason for low energy utilization.

Environment Factor Analysis
In terms of environmental factors, although a single device has advantages in carbon emissions, it ignores the environmental benefits brought about by overall optimization. In addition, the application of biogas is still lacking, resulting in an increase in carbon emission costs.

Load Factor Analysis
The transportation vehicles inside the WPB need to consume natural gas. At the same time, there are no residential users near the WPB, the internal electrical and thermal load is concentrated, and the total amount is lower than the current heat generation of the base. There are some gas loads in metallurgy, glass, electronics, and other industries that are distributed through the urban pipe network near the WPB.

MECS Coupled with WPB
Based on the typical WPB and energy conversion device in MECS, we proposed a physical planning topology, illustrated in Figure 5. The WPB includes landfills, waste incineration power plants, leachate treatment plants, and biogas power plants. The biogas compression and purification plant, P2G, and some energy storage devices are planned in the system for taking full advantage of the various energies and reducing environmentally harmful emissions.

Environment Factor Analysis
In terms of environmental factors, although a single device has advantages in carbon emissions, it ignores the environmental benefits brought about by overall optimization. In addition, the application of biogas is still lacking, resulting in an increase in carbon emission costs.

Load Factor Analysis
The transportation vehicles inside the WPB need to consume natural gas. At the same time, there are no residential users near the WPB, the internal electrical and thermal load is concentrated, and the total amount is lower than the current heat generation of the base. There are some gas loads in metallurgy, glass, electronics, and other industries that are distributed through the urban pipe network near the WPB.

MECS Coupled with WPB
Based on the typical WPB and energy conversion device in MECS, we proposed a physical planning topology, illustrated in Figure 5. The WPB includes landfills, waste incineration power plants, leachate treatment plants, and biogas power plants. The biogas compression and purification plant, P2G, and some energy storage devices are planned in the system for taking full advantage of the various energies and reducing environmentally harmful emissions.

Basic Data
The information of the intrinsic equipment in WPB is shown in Table 1, and the multi-energy complementary equipment is shown in Table 2. The data in Tables 1 and 2 are collected from a solid waste treatment base in Shanghai. Some of the equipment has not been installed, so its data are estimated based on the equipment currently available.

Basic Data
The information of the intrinsic equipment in WPB is shown in Table 1, and the multi-energy complementary equipment is shown in Table 2. The data in Tables 1 and 2 are collected from a solid waste treatment base in Shanghai. Some of the equipment has not been installed, so its data are estimated based on the equipment currently available. The energy price and the amount of waste transportation of a day in a MECS are shown in Figure 6. Figure 7 shows the output power and utilization rate of the wind turbine in a typical day. The WPB belongs to the source park, and the load in the park is very low. Because of the rigid requirements of waste disposal capacity, the generation capacity of waste incineration power plants has the lowest limit, and wind turbines are also in the state of generation. Therefore, there is basically no situation in which the energy production of WPB cannot meet the load. In the lower-level planning model, the impact of the load in the optimal scheduling is small, and the optimization result is determined by the fluctuation of the energy price and abandoned wind rate. Based on the abovementioned actual situation, the load of WPB is set to a fixed value in order to simplify the processing. The energy price and the amount of waste transportation of a day in a MECS are shown in Figure  6. Figure 7 shows the output power and utilization rate of the wind turbine in a typical day. The WPB belongs to the source park, and the load in the park is very low. Because of the rigid requirements of waste disposal capacity, the generation capacity of waste incineration power plants has the lowest limit, and wind turbines are also in the state of generation. Therefore, there is basically no situation in which the energy production of WPB cannot meet the load. In the lower-level planning model, the impact of the load in the optimal scheduling is small, and the optimization result is determined by the fluctuation of the energy price and abandoned wind rate. Based on the abovementioned actual situation, the load of WPB is set to a fixed value in order to simplify the processing.    The energy price and the amount of waste transportation of a day in a MECS are shown in Figure  6. Figure 7 shows the output power and utilization rate of the wind turbine in a typical day. The WPB belongs to the source park, and the load in the park is very low. Because of the rigid requirements of waste disposal capacity, the generation capacity of waste incineration power plants has the lowest limit, and wind turbines are also in the state of generation. Therefore, there is basically no situation in which the energy production of WPB cannot meet the load. In the lower-level planning model, the impact of the load in the optimal scheduling is small, and the optimization result is determined by the fluctuation of the energy price and abandoned wind rate. Based on the abovementioned actual situation, the load of WPB is set to a fixed value in order to simplify the processing.    Table 3 shows the capacity planning result of the intrinsic equipment and multi-energy complementary equipment of the WPB. Table 4 gives a comparison of energy, economic, and environmental benefits before and after planning.  The planned MECS coupled with WPB can improve the benefits from the three aspects of energy, economy, and environment. Firstly, the adopted planning method increases the utilization of heat and biogas. From Figure 5, the extra heat in the power plant can be supplied to the leachate plant or for external use. The biogas burns directly or is used inefficiently for generation. It is now applied to the waste transportation vehicle or for sale after compression and purification. Secondly, the maximum economic benefit shall be realized through the coordination of electricity/heat/gas according to the price of energy. In terms of the environment, the conversion of the vehicle's motive power from traditional energy to biogas is about to reduce carbon emissions significantly. Planning of the MECS coupled with WPB brings about the following benefits:

Improvement of Energy Efficiency
The original WPB has low efficiency of energy owing to the single form of energy utilization. Select two typical energy sources in MECS as an example. The form of biogas utilization is abundant and the efficiency of biogas generation is greatly improved. As for heat, the original utilization was zero, which means the heat was not used. The form and efficiency of heat are both improved effectively.
Moreover, the utilization of biogas and CH 4 forms the energy flow, cycling in the MECS, shown as Figure 5. The waste is treated to produce biogas and natural gas in WL and WI after transportation by vehicles. The formed gas can be used as fuel for vehicles after compression and purification. Vehicles continue to transport waste to the WPB. The recycling of the energy reduces the emission of biogas and final treatment, lightening the environmental pressure of economic growth.

Growth of Economic Benefits
From Table 4, it is obvious that the economic benefits of MECS coupled with WPB are higher than those of the original WPB, which can also be observed in Figure 8. The dispatch waste disposal ratio of WI and WL is about 88% and 12%, respectively, because WI achieves more profit with less cost. Therefore, the proportion of waste disposed by WI is higher to obtain more economic benefits.
From the perspective of the multi-energy complementary equipment, one main reason for higher profit after planning is the energy benefit of energy storage equipment for external sale, which cannot be obtained in the original WPB. It can be found in Table 4 that the energy benefit is a considerable part of the income of the WPB.

Promotion of Environmental Benefits
Environmental benefits mainly consider carbon emission reduction. We can consider the carbon emission reduction of the entire system in two parts: Intrinsic equipment and complementary equipment in a waste base. From Table 4, the current carbon emission reduction of WI is twice as much as that of the original, while the carbon emission reduction of BP is not changed. Moreover, vehicles transporting waste create 2515.8 t/day of carbon emission reduction. The comparison of carbon emission reductions of waste bases can be seen from Figure 8.
As a comparison, reference [51] applied a hierarchical optimization strategy to a distributed generation system in the center of a small town in the Northeast of Italy. The original energy cost of this region is €796,064/year before planning. After planning, it turns out that €53,359/year can be saved and 2714 t/year of CO2 emissions can be avoided. This study shows similar results to those of this paper, however, it lacks the consideration of energy storage equipment. Meanwhile, multiobjective optimization is used in [51], while this paper quantifies environmental cost and ecological construction cost so that the planning algorithm has only one objective.

Conclusions
This paper studies the planning method of the MECS coupled with the WPB from a case in China. Adding multi-energy complementary equipment based on the intrinsic equipment in the The dispatch waste disposal ratio of WI and WL is about 88% and 12%, respectively, because WI achieves more profit with less cost. Therefore, the proportion of waste disposed by WI is higher to obtain more economic benefits.
From the perspective of the multi-energy complementary equipment, one main reason for higher profit after planning is the energy benefit of energy storage equipment for external sale, which cannot be obtained in the original WPB. It can be found in Table 4 that the energy benefit is a considerable part of the income of the WPB.

Promotion of Environmental Benefits
Environmental benefits mainly consider carbon emission reduction. We can consider the carbon emission reduction of the entire system in two parts: Intrinsic equipment and complementary equipment in a waste base. From Table 4, the current carbon emission reduction of WI is twice as much as that of the original, while the carbon emission reduction of BP is not changed. Moreover, vehicles transporting waste create 2515.8 t/day of carbon emission reduction. The comparison of carbon emission reductions of waste bases can be seen from Figure 8.
As a comparison, reference [51] applied a hierarchical optimization strategy to a distributed generation system in the center of a small town in the Northeast of Italy. The original energy cost of this region is €796,064/year before planning. After planning, it turns out that €53,359/year can be saved and 2714 t/year of CO 2 emissions can be avoided. This study shows similar results to those of this paper, however, it lacks the consideration of energy storage equipment. Meanwhile, multi-objective optimization is used in [51], while this paper quantifies environmental cost and ecological construction cost so that the planning algorithm has only one objective.

Conclusions
This paper studies the planning method of the MECS coupled with the WPB from a case in China. Adding multi-energy complementary equipment based on the intrinsic equipment in the original WPB can not only improve energy utilization, but also accomplish economic and environmental benefits. The following conclusions can be obtained: (1) MECS is analyzed from three aspects: Energy, environment, and load. According to the results, the MECS is divided into supply, conversion, transmission, storage, and other blocks. According to the division of typical energy components and park-specific energy components, the physical planning architecture of MECS is built; (2) Based on the conventional location selection and capacity decision method of energy devices and the bi-level optimization model, the optimal scheduling of energy devices in MECS is transformed into the planning model; (3) The energy efficiency of biogas and heat is improved by constructing the BP and P2G. After planning, biogas and CH 4 are recycled throughout the WPB, which is significant for the MECS.
In addition, the original wasted heat energy in the WPB has also been fully utilized. Energy benefits for sale increases the total economic benefits, which is achieved by the supplement of power/heat/gas storage equipment. Energy storage devices make the way of energy supply and utilization in the WPB more flexible. The fuel of vehicles replaced by biogas helps enhance the carbon emission reduction.
However, the paper studies the coordination problem of a single regional pluripotent complementary system. In future research, the following issues will be considered: (1) Uncertainty factors in MECS, such as renewable energy and energy demand, are to be considered in the planning model in future research; (2) The energy collaborative optimization between multiple regions will be discussed in future research.

Conflicts of Interest:
The authors declare no conflict of interest.