A General Transformer Evaluation Method for Common-Mode Noise Behavior

: In isolated power converters, the transformer is a key part of voltage transformation and isolation. Since common-mode (CM) noise is rather di ﬃ cult to suppress compared with di ﬀ erent-mode (DM) noise, more and more scholars are paying attention to the characteristics of CM noise, especially in high-frequency CM noise behaviors. CM noise can be further divided into conducted CM noise and radiated CM noise, and the main focus of this paper is on conducted CM noise. The CM coupling capacitance of the transformer is one of the main contributors of CM noise, which has been veriﬁed in many previous studies. Hence, eliminating the CM noise in a transformer coupling path can signiﬁcantly lower the whole CM noise level of the converter. Professional conducted electromagnetic interference (EMI) testing instruments are quite expensive. In this paper, a general transformer evaluation technique for CM noise behavior is proposed. Only a signal generator and oscilloscope can achieve transformer CM noise behavior evaluation. PCB planar ﬂyback transformers are designed, and a series of noise spectrums and voltage waveforms can verify the e ﬀ ectiveness of the proposed transformer evaluation method. The ﬂyback adapter porotype can pass the EMI standard limited line EN55022 class B by the proposed evaluation method.


Introduction
Switch-mode power supplies (SMPSs) have been widely used in both high power applications and low power applications. The flyback converter is one of the most commonly used topologies, especially in low power isolated converters such as mobile phone chargers, laptop power adapters, etc. Higher switching frequency and higher power density are the future development tendencies for isolated power converters, in order to achieve lower cost and smaller volume size. The efficiency, power density, and electromagnetic compatibility (EMC) are the key factors for power supplies, but they contradict each other. Since a higher switching frequency is helpful to achieve higher power density, it also brings many challenges in electromagnetic interference (EMI) issues. Figure 1 shows the propagation paths of electromagnetic interference noise in the isolated power converter. Generally, EMI noise can be categorized into conduction emission (CE), EMI noise, and radiation emission (RE) EMI noise. For radiation emission EMI noise, it will radiate electromagnetic energy into space, which will be received by the antenna. Then, the EMI receiver will display the noise spectrum of RE EMI noise. For conductive emission EMI noise, it can be further decoupled as different-mode (DM) noise and common-mode (CM) noise according to its propagation path. For DM noise, it will flow through L and N lines in the opposite direction. For CM noise, it will flow through L and N lines in the same direction to ground. The CM noise is harder to be suppressed compared to the DM noise because of its complex conduction paths influenced by stray inductive parameters and capacitive A series of CM noise eliminating techniques have been proposed in [4][5][6][7][8][9][10], and these techniques can be mainly categorized into two types: The first is to eliminate the CM noise flowing through the parasitic capacitance between the drain of the primary MOSFET and the ground. For this part of CM noise, if the heatsink is attached to the primary MOSFET, it will, via the parasitic capacitance between the heatsink and the ground to line impedance stabilization network (LISN) [11]. If the heatsink is connected to the primary ground, this part of the CM noise will not flow to LISN, it will just circulate internally between the primary side and the heatsink. The second is to optimize the design of the transformer in order to attenuate the CM noise flowing through the coupling capacitance of the transformer. Scholars have proposed many kinds of noise cancellation techniques [5][6][12][13]. Adding Y-cap can make the CM noise flowing through the interwinding capacitance of the transformer circulate internally instead of being detected by LISN. However, if the capacitance of the Y-cap is too large this technique may cause large leakage current [4], which is harmful to the human body. Besides, isolated power converters without a Y-cap are the development tendency in the future. Adding double shielding copper foil between the adjacent primary and secondary windings can totally eliminate CM noise in the transformer path, but this technique is impractical since it will increase the manufacturing cost, winding loss, and complicate the manufacturing process [5]. The basic CM noise balance principle of [6][7] is to achieve zero voltage difference between the adjacent primary and secondary winding layers, which can make sure that the induced electric charge in the secondary side is equal to zero. Then there is no CM current flowing through transformer coupling path. Hence, [5] proposed that adjusting the winding arrangement of the primary and secondary wining layers can achieve voltage potential balance between the adjacent primary and secondary winding layers. This method will limit the flexibility of the winding arrangement.
There are many studies analyzing the modeling of the parasitic capacitance of the transformer. Reference [12] proposed that the parasitic capacitance of a transformer with two windings can be modeled with six capacitances to apply the energy conservation. However, this model is too complex to achieve circuit analysis. The equivalent lumped capacitance is used to represent the CM noise A series of CM noise eliminating techniques have been proposed in [4][5][6][7][8][9][10], and these techniques can be mainly categorized into two types: The first is to eliminate the CM noise flowing through the parasitic capacitance between the drain of the primary MOSFET and the ground. For this part of CM noise, if the heatsink is attached to the primary MOSFET, it will, via the parasitic capacitance between the heatsink and the ground to line impedance stabilization network (LISN) [11]. If the heatsink is connected to the primary ground, this part of the CM noise will not flow to LISN, it will just circulate internally between the primary side and the heatsink. The second is to optimize the design of the transformer in order to attenuate the CM noise flowing through the coupling capacitance of the transformer. Scholars have proposed many kinds of noise cancellation techniques [5, 6,12,13]. Adding Y-cap can make the CM noise flowing through the interwinding capacitance of the transformer circulate internally instead of being detected by LISN. However, if the capacitance of the Y-cap is too large this technique may cause large leakage current [4], which is harmful to the human body. Besides, isolated power converters without a Y-cap are the development tendency in the future. Adding double shielding copper foil between the adjacent primary and secondary windings can totally eliminate CM noise in the transformer path, but this technique is impractical since it will increase the manufacturing cost, winding loss, and complicate the manufacturing process [5]. The basic CM noise balance principle of [6,7] is to achieve zero voltage difference between the adjacent primary and secondary winding layers, which can make sure that the induced electric charge in the secondary side is equal to zero. Then there is no CM current flowing through transformer coupling path. Hence, [5] proposed that adjusting the winding arrangement of the primary and secondary wining layers can achieve voltage potential balance between the adjacent primary and secondary winding layers. This method will limit the flexibility of the winding arrangement.
There are many studies analyzing the modeling of the parasitic capacitance of the transformer. Reference [12] proposed that the parasitic capacitance of a transformer with two windings can be Energies 2019, 12,1984 3 of 21 modeled with six capacitances to apply the energy conservation. However, this model is too complex to achieve circuit analysis. The equivalent lumped capacitance is used to represent the CM noise behavior of the transformer [7,[13][14][15], which can keep the displacement current rule. Then, the CM noise behaviors of the isolated power converters such as flyback converter, forward converter, and LLC resonant converter are analyzed in [7,8] based on displacement current rule. With the help of the previous efforts [7,8,[12][13][14][15][16], this paper will propose a general transformer evaluation method for CM noise behavior. Only a signal generator and an oscilloscope can effectively evaluate the CM noise behavior of the transformer in the low-frequency range, which is easy to be implemented without the expensive cost of the professional CE EMI testing instruments. This paper is organized as follows. In Section 2, the capacitance model of the transformer is first introduced for CM noise analysis. Based on the model, the CM noise flowing characteristic in the transformer coupling path is analyzed under different circuit configurations. In Section 3, the displacement current flowing through transformer coupling path under different winding arrangements is calculated. In Section 4, a general transformer evaluation method for CM noise behavior is proposed, and some key factors are also analyzed and discussed in detail. In Section 5, several transformers with different winding configurations are used to evaluate by the proposed method, and the measured noise spectrums can verify the effectiveness of the proposed evaluation method. Section 6 concludes this paper.

Transformer CM Noise Model
Many previous references have proposed the CM noise model of the transformer. As shown in Figure 2a, for four terminals of a transformer there are six equivalent lumped capacitances [12]. C AB and C CD represent the intrawinding capacitance, which has nothing to do with the CM displacement current conduction between primary and secondary and can be neglected in the CM noise model. The voltage potential of terminals A, B, C, and D are defined as V A , V B , V C , and V D , respectively. The displacement current flowing through the interwinding capacitance C AC , C BD , C BC , and C AD can be calculated by There are three lumped capacitances-CBC, CBD, and CAC-to determine the displacement current flowing through transformer coupling path. To further simplify the expression (2), CBC + CBD and CBC + CAC are defined as Cps and Csp, respectively. For flyback topology with three-wires (L, N, and GND wires), the voltage difference between the primary ground (PG) and the secondary ground (SG) can be omitted due to the small voltage drop on LISN. For flyback topology with two-wires (L and N wires), the voltage difference can also be neglected if the parasitic capacitance Csg between the secondary ground and the ground is far larger than CQ (CQ is the equivalent lumped capacitance of the transformer and it will be introduced in Section 4). The CM current flowing through the transformer can be expressed as  In a flyback topology, the winding connection is shown in Figure 2a. Points B and C are voltage hot points, which are connected to the primary MOSFET and the secondary diode, respectively. Points A and D are voltage static points, which are connected to the primary ground and the secondary ground, respectively. Because points A and D will not generate dv/dt, the expression (1) can be further simplified as (2): There are three lumped capacitances-C BC , C BD , and C AC -to determine the displacement current flowing through transformer coupling path. To further simplify the expression (2), C BC + C BD and C BC + C AC are defined as C ps and C sp , respectively. For flyback topology with three-wires (L, N, and GND wires), the voltage difference between the primary ground (PG) and the secondary ground (SG) can be omitted due to the small voltage drop on LISN. For flyback topology with two-wires (L and N wires), the voltage difference can also be neglected if the parasitic capacitance C sg between the secondary ground and the ground is far larger than C Q (C Q is the equivalent lumped capacitance of the transformer and it will be introduced in Section 4). The CM current flowing through the transformer can be expressed as where C ps is an equivalent lumped capacitance, which represents that the primary CM noise source generates CM current flowing through C ps to the secondary side. It is connected between the primary voltage hot point and the secondary static point. Similarly, C sp represents that the secondary CM noise source generates CM current flowing through C sp to the primary side. Figure 2b depicts the transformer winding two-capacitance model. Here, i ps is defined as V p *C ps and i sp is defined as V s *C sp . If i ps is equal to i sp , the CM current flowing through transformer will have the opportunity to be totally canceled due to their same amplitudes and opposite phases. Figure 3a is the CM noise circuit model of the flyback converter when the diode is used in the secondary side. It can clearly find that the CM current i sp is antiphase with i ps and i pg . It is possible to make a balance among i sp , i ps , and i pg . i pg is the displacement current flowing through parasitic capacitance between the drain of the primary MOSFET and the ground. Figure 3b show the CM noise circuit model of the flyback converter when the MOSFET is used in the secondary side. The phase of the secondary CM noise source has inversed if the secondary MOSFET is located in the secondary ground to simplify its gate driving. It is impossible to make a balance among i sp , i ps , and i pg . In order to improve this situation, an antiphase winding is added between the adjacent primary and secondary windings to generate an antiphase CM displacement current to cancel i sp and i ps . Z1-Z6 represent the parasitic parameters of the CM noise conduction paths. n and n1 are the turn ratio between the primary winding and the secondary winding and between the primary winding and the antiphase winding, respectively.

Calculation of the CM Displacement Current Flowing through Transformer Coupling Path
Figure 4a-c shows the transformer winding structure with the different winding arrangements. Various kinds of winding arrangements are proposed in previous references for some particular considerations. For instance, the transformer with interleaved winding structure can afford the minimal winding loss at the cost of large interwinding capacitance, which will worsen EMI characteristic. The transformer with PS ( primary secondary) winding structure can lower the EMI characteristic but this action will sacrifice the efficiency of the converter. For calculating the CM displacement current flowing through the inerwinding capacitance of the transformer, it should be noticed that only the displacement current flowing through the adjacent primary and secondary winding can be called CM noise current. Hence, the following will introduce the basic method of calculating the displacement current flowing through transformer coupling path under different winding arrangements.
It is assumed that the turn number of windings Wp1, Wp2, Wp3, Wp4, Ws1, and Ws2 are Np1, Np2, Np3, Np4, Ns1, and Ns2, respectively. Hence, the voltage potential distribution along each turn can be expressed as follows. The voltage differences between two terminals of the primary winding, and between two terminals of the secondary winding are defined as vp and vs, respectively. They should satisfy where vA, vB, vC, and vD are the voltage potentials of the primary and secondary winding terminals. It is assumed that the voltage potential distribution along each winding is evenly and linearly distributed. The reason why the voltage potential varies linearly along the winding is that the effect of leakage inductance, the skin effect, and the proximity effect are ignored. The expressions of the voltage potential distribution of each layer are as follows.

Calculation of the CM Displacement Current Flowing through Transformer Coupling Path
Figure 4a-c shows the transformer winding structure with the different winding arrangements. Various kinds of winding arrangements are proposed in previous references for some particular considerations. For instance, the transformer with interleaved winding structure can afford the minimal winding loss at the cost of large interwinding capacitance, which will worsen EMI characteristic. The transformer with PS ( primary secondary) winding structure can lower the EMI characteristic but this action will sacrifice the efficiency of the converter. For calculating the CM displacement current flowing through the inerwinding capacitance of the transformer, it should be noticed that only the displacement current flowing through the adjacent primary and secondary winding can be called CM noise current. Hence, the following will introduce the basic method of calculating the displacement current flowing through transformer coupling path under different winding arrangements. The structure capacitance, Cstr, can be approximated as a plate capacitor to calculate its capacitance. Reference [15] deduced the accurate formula:  It is assumed that the turn number of windings W p1 , W p2 , W p3 , W p4 , W s1 , and W s2 are N p1 , N p2 , N p3 , N p4 , N s1 , and N s2 , respectively. Hence, the voltage potential distribution along each turn can be expressed as follows. The voltage differences between two terminals of the primary winding, and between two terminals of the secondary winding are defined as v p and v s , respectively.
where v A , v B , v C , and v D are the voltage potentials of the primary and secondary winding terminals. It is assumed that the voltage potential distribution along each winding is evenly and linearly distributed. The reason why the voltage potential varies linearly along the winding is that the effect of leakage inductance, the skin effect, and the proximity effect are ignored. The expressions of the voltage potential distribution of each layer are as follows.
Energies 2019, 12, 1984 The structure capacitance, C str , can be approximated as a plate capacitor to calculate its capacitance. Reference [15] deduced the accurate formula: where ε 0 is the permittivity of the vacuum and ε r is the relative permittivity of the dialect between the two adjacent winding layers. d 1 and d 2 are the distance between the primary (secondary) and the center column of the magnetic core. Figure 4a shows a transformer winding structure under PS arrangement. For calculating the CM displacement current i CM_dis under a PS winding arrangement, calculating the displacement current between the layers W p1 and W s1 is enough. Then, the CM displacement current i CM_dis is

PS Winding Arrangement
where C p4-s1 is the structure capacitance between the adjacent layers P4 and S1 that can be calculated according to (12). Figure 4b shows a transformer winding structure under the sandwich structure. The CM displacement current between adjacent primary and secondary winding is represented by i p2s1 and i p3s2 . Then, the total CM displacement current is

Sandwich Winding Arrangement
where C p2-s1 and C p3-s2 are the structure capacitance between adjacent layers P2 and S1 and between layers P3 and S2 that can be calculated according to (12).  Figure 4c shows a transformer winding structure under interleaved structure. The CM displacement current between the adjacent primary and secondary winding are i p2s1 , i p3s1 , i p3s2 and i p4s2 . Then, the total CM displacement current is

Interleaved Winding Arrangement
where C p2-s1 , C p3-s1 , C p3-s2 and C p4-s2 are the structure capacitance between adjacent layers P2 and S1, layers P3 and S1, layers P3 and S2, and layers P4 and S2, respectively. They can be calculated according to (12). According to (13)- (15), it can find that the CM displacement current is generated due to the existence of the voltage potential distribution along with the adjacent primary and secondary winding. Only the displacement current flowing through the adjacent primary and secondary winding can contribute to forming the CM current. The essence of the CM displacement current is the electric charge induced in the secondary side. Hence, if the average voltage potential distributions along the primary and secondary winding are equal, there is no CM charge induced in the secondary side.

Previous Evaluation Method
Many previous references also have discussed the issue on how to evaluate the CM noise behavior of the transformer [17][18][19][20]. Figure 5a,b depicts the traditional transformer CM characteristic evaluation method. Using impedance analyzer to measure the CM capacitance of the transformer is impractical. Because this method will not make the primary and the secondary winding build the voltage potential distribution along each winding, and this method can only measure the structure capacitance of the transformer. According to (13)- (15), it can find that the CM displacement current is both related to the structure capacitance between adjacent primary and secondary winding layers and the voltage potential distribution of the winding; merely measuring the structure capacitance cannot effectively reflect the CM displacement current characteristic of the transformer. As have discussed above, the CM noise in transformer coupling path is formed by the voltage potential distribution. Therefore this method cannot totally represent the conductive CM noise behavior of the transformer. In order to take the voltage potential distribution along with the winding into consideration, reference [19], proposed using an EMI receiver (spectrum analyzer, network analyzer) with a TG option to measure the insertion loss (IL) in order to evaluate the transformer as shown in Figure 6. The positive terminal of the TG is connected to voltage hot point of the primary side and the ground terminal of TG is connected to the primary voltage static point. TG will output sinusoidal signal assigned on the primary winding, and its amplitude is 1 V. Then, the secondary winding will form the voltage potential distribution along with each turn. In this method, the transformer is regarded as a pure capacitance to conduct CM noise. The CM displacement current will flow through this equivalent CM noise capacitance and generate voltage drop in resistor R2, as shown in Figure 6b. Resistor R2 is located in the RF input terminal. Based on the definition of the insertion loss, a lumped equivalent capacitance CQ can be calculated to evaluate the CM noise characteristic of the transformer, according to (16). This method is very effective to evaluate the CM noise behavior of the transformer in lowfrequency range since the capacitive coupling contributes more in low-frequency range, and for In order to take the voltage potential distribution along with the winding into consideration, reference [19], proposed using an EMI receiver (spectrum analyzer, network analyzer) with a TG option to measure the insertion loss (IL) in order to evaluate the transformer as shown in Figure 6. The positive terminal of the TG is connected to voltage hot point of the primary side and the ground terminal of TG is connected to the primary voltage static point. TG will output sinusoidal signal assigned on the primary winding, and its amplitude is 1 V. Then, the secondary winding will form the voltage potential distribution along with each turn. In this method, the transformer is regarded as a pure capacitance to conduct CM noise. The CM displacement current will flow through this equivalent CM noise capacitance and generate voltage drop in resistor R 2 , as shown in Figure 6b. Resistor R 2 is located in the RF input terminal. Based on the definition of the insertion loss, a lumped equivalent capacitance C Q can be calculated to evaluate the CM noise characteristic of the transformer, according to (16). In order to take the voltage potential distribution along with the winding into consideration, reference [19], proposed using an EMI receiver (spectrum analyzer, network analyzer) with a TG option to measure the insertion loss (IL) in order to evaluate the transformer as shown in Figure 6. The positive terminal of the TG is connected to voltage hot point of the primary side and the ground terminal of TG is connected to the primary voltage static point. TG will output sinusoidal signal assigned on the primary winding, and its amplitude is 1 V. Then, the secondary winding will form the voltage potential distribution along with each turn. In this method, the transformer is regarded as a pure capacitance to conduct CM noise. The CM displacement current will flow through this equivalent CM noise capacitance and generate voltage drop in resistor R2, as shown in Figure 6b. Resistor R2 is located in the RF input terminal. Based on the definition of the insertion loss, a lumped equivalent capacitance CQ can be calculated to evaluate the CM noise characteristic of the transformer, according to (16). This method is very effective to evaluate the CM noise behavior of the transformer in lowfrequency range since the capacitive coupling contributes more in low-frequency range, and for higher frequency range inductive coupling is a major factor for conductive CM noise. However, the main drawback of this method is that needs expensive test instruments (EMI receiver with TG option  This method is very effective to evaluate the CM noise behavior of the transformer in low-frequency range since the capacitive coupling contributes more in low-frequency range, and for higher frequency range inductive coupling is a major factor for conductive CM noise. However, the main drawback of this method is that needs expensive test instruments (EMI receiver with TG option or spectrum analyzer with TG option). Many transformer manufacturers do not have enough money to afford these professional instruments. Besides, precise calibration of these professional instruments is also needed, which complicates the measurement process. Reference [21] proposed using numerical algorithms to achieve parameter extraction and parameter identification of the transformer. Besides, some numerical methods for transformer evaluation in [9,22] have been proposed to design wire-wound transformers. However, these evaluation methods are based on the finite element method (FEM) commercial simulation software, i.e., Ansys Maxwell which is too expensive to be purchased by some transformer manufactures.

Proposed Evaluation Method
Based on the above considerations, this paper proposes a practical CM noise characteristic evaluation method to achieve the same evaluation effect as discussed above. Only a signal generator and an oscilloscope can achieve the same evaluation effect in low-frequency EMI noise as shown in  higher frequency range inductive coupling is a major factor for conductive CM noise. However, the main drawback of this method is that needs expensive test instruments (EMI receiver with TG option or spectrum analyzer with TG option). Many transformer manufacturers do not have enough money to afford these professional instruments. Besides, precise calibration of these professional instruments is also needed, which complicates the measurement process. Reference [21] proposed using numerical algorithms to achieve parameter extraction and parameter identification of the transformer. Besides, some numerical methods for transformer evaluation in [9,22] have been proposed to design wire-wound transformers. However, these evaluation methods are based on the finite element method (FEM) commercial simulation software, i.e., Ansys Maxwell which is too expensive to be purchased by some transformer manufactures.

Proposed Evaluation Method
Based on the above considerations, this paper proposes a practical CM noise characteristic evaluation method to achieve the same evaluation effect as discussed above. Only a signal generator and an oscilloscope can achieve the same evaluation effect in low-frequency EMI noise as shown in

Selection of Resistor R2
It seems that the evaluation methods of the EMI receiver with TG option and the signal generator are the same. However, there is a significant difference in the selection of the resistance of R2 that will be analyzed in detail in the following.
The EMI receiver with TG option and the network analyzer are high-precision instruments for measuring small signals. Its sampling resistor R2 depicted in Figure 6a uses precision noninductive resistance, which means that the resistor component R2 can be regarded as pure resistance. Then, the  It seems that the evaluation methods of the EMI receiver with TG option and the signal generator are the same. However, there is a significant difference in the selection of the resistance of R 2 that will be analyzed in detail in the following.
The EMI receiver with TG option and the network analyzer are high-precision instruments for measuring small signals. Its sampling resistor R 2 depicted in Figure 6a uses precision noninductive resistance, which means that the resistor component R 2 can be regarded as pure resistance. Then, the impedance will remain unchanged equaling to 50 Ω as the frequency increases. The EMI receiver and network analyzer are both used in conductive EMI noise frequency ranges (150 KHz-30 MHz) due to the EMI test standard of the switch-mode power supplies (SMPSs). The insertion loss (IL) and S parameters can be measured by these instruments. Hence, the tiny voltage drop in resistor R 2 can be precisely measured due to its high precision. However, if the same resistance is used for resistor R 2 in the proposed evaluation method to sample the CM noise voltage, it will be impractical. That is because the size of the CM noise displacement current is extremely tiny, which is at the level of microampere. Then, the voltage drop in R 2 is tiny, which cannot be precisely measured by the voltage probe. Hence, choosing a proper resistance is critical in the proposed evaluation method.
The distributed CM coupling capacitance of the transformer is represented as a lumped capacitance C Q for simplifying the analysis. Figure 8 shows the equivalent circuit of the proposed evaluation method. The CM displacement current i cm flowing through the lumped equivalent capacitance C Q can be expressed as impedance will remain unchanged equaling to 50 Ω as the frequency increases. The EMI receiver and network analyzer are both used in conductive EMI noise frequency ranges (150 KHz-30 MHz) due to the EMI test standard of the switch-mode power supplies (SMPSs). The insertion loss (IL) and S parameters can be measured by these instruments. Hence, the tiny voltage drop in resistor R2 can be precisely measured due to its high precision. However, if the same resistance is used for resistor R2 in the proposed evaluation method to sample the CM noise voltage, it will be impractical. That is because the size of the CM noise displacement current is extremely tiny, which is at the level of microampere. Then, the voltage drop in R2 is tiny, which cannot be precisely measured by the voltage probe. Hence, choosing a proper resistance is critical in the proposed evaluation method. The distributed CM coupling capacitance of the transformer is represented as a lumped capacitance CQ for simplifying the analysis. Figure 8 shows the equivalent circuit of the proposed evaluation method. The CM displacement current icm flowing through the lumped equivalent capacitance CQ can be expressed as ac cm The voltage drop U2 in sampling resistor R2 is In order to represent the variation tendency of the CM displacement current icm and the voltage drop U2 in resistor R2 versus the resistance of R2, the capacitance of CQ will be assumed to be a certain value. For different value of CQ, the basic variation tendencies of icm and U2 are almost the same. In the analysis, it is assumed as 10 pF. The root mean square (RMS) of Vac is 4 V. Then, the size of the CM displacement current icm and the voltage drop U2 can be calculated under different frequencies.
For general isolated SMPS, its switch frequency is from 10 kHz to 1 MHz, and a switching frequency will be chosen as signal excitation frequency to evaluate the transformer. Figure 9a,b shows the frequency-dependent curve of icm and U2. Figure 9a shows that the larger resistance of R2 will cause less displacement current icm for the same transformer. Figure 9b shows that larger resistance of R2 will cause a larger voltage drop in itself. If the resistance of R2 is equal to 50 Ω, the voltage drop in R2 will be too tiny to be precisely measured. Therefore, the resistor with 50 Ω is impractical for use in this evaluation method due to the limitation of probe accuracy. In order to acquire a larger voltage drop in R2, the effective implementation is to increase the resistance of R2 to sample the larger voltage. The voltage drop in R2 will increase if the resistance of R2 is increased. However, if the resistance of R2 is too large, it will also be unreasonable The voltage drop U 2 in sampling resistor R 2 is In order to represent the variation tendency of the CM displacement current i cm and the voltage drop U 2 in resistor R 2 versus the resistance of R 2 , the capacitance of C Q will be assumed to be a certain value. For different value of C Q , the basic variation tendencies of i cm and U 2 are almost the same. In the analysis, it is assumed as 10 pF. The root mean square (RMS) of V ac is 4 V. Then, the size of the CM displacement current i cm and the voltage drop U 2 can be calculated under different frequencies.
For general isolated SMPS, its switch frequency is from 10 kHz to 1 MHz, and a switching frequency will be chosen as signal excitation frequency to evaluate the transformer. Figure 9a,b shows the frequency-dependent curve of i cm and U 2 . Figure 9a shows that the larger resistance of R 2 will cause less displacement current i cm for the same transformer. Figure 9b shows that larger resistance of R 2 will cause a larger voltage drop in itself. If the resistance of R 2 is equal to 50 Ω, the voltage drop in R 2 will be too tiny to be precisely measured. Therefore, the resistor with 50 Ω is impractical for use in this evaluation method due to the limitation of probe accuracy. In order to acquire a larger voltage drop in R 2 , the effective implementation is to increase the resistance of R 2 to sample the larger voltage. The voltage drop in R 2 will increase if the resistance of R 2 is increased. However, if the resistance of R 2 is too large, it will also be unreasonable For larger resistance of R2, the voltage difference between the primary ground and the secondary ground will change. The voltage potential distribution of the secondary winding will change versus R2 resistance, and the value of the lumped CM capacitance of the transformer can change. The following will analyze the influence of R2 resistance on the lumped equivalent capacitance CQ in detail.
A transformer with a single layer of the primary and the secondary winding is used to illustrate this phenomenon, as shown in Figure 10a. Figure 10b shows the voltage potential distribution of the primary and secondary winding and their expression can be given as follows where Np and Ns are the turns of the primary and secondary winding, respectively. Vd is the voltage difference between the primary ground and the secondary ground. h is the height of the core window. According to (19) and (20) From (21), it can be found that the dynamic CM capacitance CQ is not only determined by the structure capacitance C0 and the terminal connection of winding, but also determined by the voltage potential difference Vd between the primary ground and the secondary ground.
The essential reason for this phenomenon is that Vd changes the voltage potential distribution of the secondary winding and the resultant electric charges induced in the secondary side can also be changed. Hence, the resistance of R2 should be chosen appropriately. For larger resistance of R 2 , the voltage difference between the primary ground and the secondary ground will change. The voltage potential distribution of the secondary winding will change versus R 2 resistance, and the value of the lumped CM capacitance of the transformer can change. The following will analyze the influence of R 2 resistance on the lumped equivalent capacitance C Q in detail.
A transformer with a single layer of the primary and the secondary winding is used to illustrate this phenomenon, as shown in Figure 10a. Figure 10b shows the voltage potential distribution of the primary and secondary winding and their expression can be given as follows where N p and N s are the turns of the primary and secondary winding, respectively. V d is the voltage difference between the primary ground and the secondary ground. h is the height of the core window.

Ground Potential Difference
For isolated converters with three wires (L, N, and GND lines), the secondary ground is directly connected to ground. This means the voltage difference between the primary ground and the secondary ground is just the voltage drop in LISN by common-mode noise, as shown in Figure 11a, if the voltage drop of the rectifier bridge is ignored. Obviously, the voltage drop in LISN is usually very small, compared with the voltages of the primary and secondary noise sources, i.e., the voltages of primary MOSFET and secondary MOSFET. Therefore, the potential difference between the primary ground and the secondary ground can be omitted when the isolated converter has three wires. In this kind of circuit configuration, the resistance chosen for R2 should be as small as possible, According to (19) and (20), the dynamic CM capacitance C Q can be calculated as From (21), it can be found that the dynamic CM capacitance C Q is not only determined by the structure capacitance C 0 and the terminal connection of winding, but also determined by the voltage potential difference V d between the primary ground and the secondary ground. The essential reason for this phenomenon is that V d changes the voltage potential distribution of the secondary winding and the resultant electric charges induced in the secondary side can also be changed. Hence, the resistance of R 2 should be chosen appropriately.

Ground Potential Difference
For isolated converters with three wires (L, N, and GND lines), the secondary ground is directly connected to ground. This means the voltage difference between the primary ground and the secondary ground is just the voltage drop in LISN by common-mode noise, as shown in Figure 11a, if the voltage drop of the rectifier bridge is ignored. Obviously, the voltage drop in LISN is usually very small, compared with the voltages of the primary and secondary noise sources, i.e., the voltages of primary MOSFET and secondary MOSFET. Therefore, the potential difference between the primary ground and the secondary ground can be omitted when the isolated converter has three wires. In this kind of circuit configuration, the resistance chosen for R 2 should be as small as possible, and the voltage drop in R 2 should be maintained so that it can be precisely measured.

Ground Potential Difference
For isolated converters with three wires (L, N, and GND lines), the secondary ground is directly connected to ground. This means the voltage difference between the primary ground and the secondary ground is just the voltage drop in LISN by common-mode noise, as shown in Figure 11a, if the voltage drop of the rectifier bridge is ignored. Obviously, the voltage drop in LISN is usually very small, compared with the voltages of the primary and secondary noise sources, i.e., the voltages of primary MOSFET and secondary MOSFET. Therefore, the potential difference between the primary ground and the secondary ground can be omitted when the isolated converter has three wires. In this kind of circuit configuration, the resistance chosen for R2 should be as small as possible, and the voltage drop in R2 should be maintained so that it can be precisely measured.
For isolated converters with two-wires (L and N wires), the secondary ground is floating. So the voltage drop between the primary ground and the secondary ground is determined by both the value of CM current and the parasitic capacitance Csg between the secondary ground and ground as shown in Figure 11b. In this case, whether the voltage difference between the primary ground and the secondary ground can be ignored or not depends on the value comparison of Csg and CQ. If CQ is much smaller than Csg, the voltage difference between the primary ground and the secondary ground can be regarded as 0. If the condition mentioned above cannot be met, the accuracy of the proposed method will be affected. However, the transformer CM coupling path is one of the major CM noise conduction paths. Eliminating the CM noise flowing through transformer coupling path can significantly lower the CM noise of the whole converter. When the designed transformer can achieve zero CM noise in transformer coupling path, the voltage difference between the primary ground and the secondary ground can be omitted. Hence, when the isolated converter is with two wires, the proposed method still can precisely evaluate the transformer with the minimum value of the CM noise. Therefore, the resistance of R2 should be chosen as small as possible. For isolated converters with two-wires (L and N wires), the secondary ground is floating. So the voltage drop between the primary ground and the secondary ground is determined by both the value of CM current and the parasitic capacitance C sg between the secondary ground and ground as shown in Figure 11b. In this case, whether the voltage difference between the primary ground and the secondary ground can be ignored or not depends on the value comparison of C sg and C Q . If C Q is much smaller than C sg , the voltage difference between the primary ground and the secondary ground can be regarded as 0. If the condition mentioned above cannot be met, the accuracy of the proposed method will be affected. However, the transformer CM coupling path is one of the major CM noise conduction paths. Eliminating the CM noise flowing through transformer coupling path can significantly lower the CM noise of the whole converter. When the designed transformer can achieve zero CM noise in transformer coupling path, the voltage difference between the primary ground and the secondary ground can be omitted. Hence, when the isolated converter is with two wires, the proposed method still can precisely evaluate the transformer with the minimum value of the CM noise. Therefore, the resistance of R 2 should be chosen as small as possible.
Based on the above discussion, the resistance of sampling resistor R 2 should be chosen appropriately. If the resistance of sampling resistor R 2 is too small it can lead to a small voltage drop in R 2 , which cannot be precisely measured by the voltage probe. If the resistance is too large it can lead to a large voltage drop in R 2 , which will change the voltage potential distribution of the secondary winding and the lumped equivalent capacitance of the transformer will be changed at the same time. It should be pointed out that the main drawbacks and limitations of the proposed evaluation method are that it can only effectively evaluate low-frequency CM noise behaviors of the transformer. Because the transformer is regarded as a pure capacitance to conduct CM noise in the proposed evaluation method the capacitive coupling plays a major role in low-frequency CM noise conduction. In the high-frequency range, both capacitive and inductive coupling will make a difference in high-frequency CM noise and the transformer cannot be regarded as a pure capacitance to conduct CM noise. Besides, the proposed evaluation method may not be applicable to do further analysis in high-frequency CM noise compared with the previous methods with EMI receiver and network analyzer. That is due to the accuracy of the test instrument. Higher frequency CM noise suppression can be solved by the design of the CM EMI filter.

Experimental Results
In order to verify the effectiveness of the proposed evaluation method, a flyback converter prototype with the different winding arrangement of the PCB planar transformer is used to verify. The secondary side of the designed transformer is connected to MOSFET to achieve synchronous rectification and its detailed circuit specification is shown in Table 1. The designed flyback adapter has three wires. There are three planar transformers with different turns of the compensation winding. They are labeled as 1#, 2#, and 3#, respectively. For 1#, 2#, and 3# transformers, the turns of the compensation winding are 8, 10, and 12 turns, respectively. The compensation winding is inserted in between the adjacent primary and secondary windings.
The measurement platform is shown in Figure 12, where the signal generator is Agilent 33522 A and the oscilloscope is Agilent DSO-X3024 A. The differential probe is Agilent N2790 A. As for the selection of the sampling resistor, the basic principles have been discussed in Section 4. Hence, this section will verify the significance of selecting a proper resistance of the sampling resistor. Besides, it is also important to select a suitable signal source applied in the primary winding. adjacent primary and secondary windings.
The measurement platform is shown in Figure 12, where the signal generator is Agilent 33522 A and the oscilloscope is Agilent DSO-X3024 A. The differential probe is Agilent N2790 A. As for the selection of the sampling resistor, the basic principles have been discussed in Section 4. Hence, this section will verify the significance of selecting a proper resistance of the sampling resistor. Besides, it is also important to select a suitable signal source applied in the primary winding.

Measurement Voltage Waveform
The signal generator can output sinusoidal signal, square signal, and triangular signal. As shown in Figures 13-15, different kinds of excitation sources are used to evaluate the transformer, respectively. The resistor R 2 with 10k Ω is used and the frequency of the signal source is 85 kHz determined by the switching frequency of the converter. The peak-to-peak value of the signal source is 4 V.

Measurement Voltage Waveform
The signal generator can output sinusoidal signal, square signal, and triangular signal. As shown in Figures 13-15, different kinds of excitation sources are used to evaluate the transformer, respectively. The resistor R2 with 10k Ω is used and the frequency of the signal source is 85 kHz determined by the switching frequency of the converter. The peak-to-peak value of the signal source is 4 V. Figure 13a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the signal generator outputs triangular signal assigned on two terminals of the primary winding. It can find that the triangular signal excitation has been distorted. This phenomenon is due to the power limitation of the signal generator. It is clear that the peak-to-peak value of the voltage in 1# transformer is the minimum and the peak-to-peak value of the voltage in 3# transformer is the maximum. As has been analyzed in section 4, 1# transformer has the minimum value of CQ, which will lead to the lowest level of CM noise spectrum. However, there is a problem in waveform distortion of the signal source applied in primary winding, which may affect the precision of the evaluation method. Similarly, Figure 14a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the sinusoidal signal is assigned on two terminals of the primary winding. The sinusoidal degree of the signal source is very well compared with that shown in Figure 13. The measurement results are the same as that of using the triangular signal and the sinusoidal signal source does not distort much.

Measurement Voltage Waveform
The signal generator can output sinusoidal signal, square signal, and triangular signal. As shown in Figures 13-15, different kinds of excitation sources are used to evaluate the transformer, respectively. The resistor R2 with 10k Ω is used and the frequency of the signal source is 85 kHz determined by the switching frequency of the converter. The peak-to-peak value of the signal source is 4 V. Figure 13a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the signal generator outputs triangular signal assigned on two terminals of the primary winding. It can find that the triangular signal excitation has been distorted. This phenomenon is due to the power limitation of the signal generator. It is clear that the peak-to-peak value of the voltage in 1# transformer is the minimum and the peak-to-peak value of the voltage in 3# transformer is the maximum. As has been analyzed in section 4, 1# transformer has the minimum value of CQ, which will lead to the lowest level of CM noise spectrum. However, there is a problem in waveform distortion of the signal source applied in primary winding, which may affect the precision of the evaluation method. Similarly, Figure 14a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the sinusoidal signal is assigned on two terminals of the primary winding. The sinusoidal degree of the signal source is very well compared with that shown in Figure 13. The measurement results are the same as that of using the triangular signal and the sinusoidal signal source does not distort much.  Figure 15a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the square signal is assigned on two terminals of the primary winding. It can clearly find that the square signal has distorted severely, which cause the voltage waveform on the sampling resistor to be no longer a standard rectangular wave. There are two peaks in the rising and falling edges of the voltage in R2.
Compared with the experiment results from Figures 13-15, the sinusoidal signal source has a minimum distortion degree. Hence, the sinusoidal signal source is recommended as an excitation source to be applied on the primary winding. Figure 16a-c shows the measurement results of the voltage waveform in sample resistor when the signal generator outputs sinusoidal signal assigned on two terminals of the primary winding. The resistor R2 with 50 Ω is used. It is clear that the peak-to-peak values of the sample voltages in 1#, 2#, and 3# transformers are almost the same. As have been analyzed in Section 4, this phenomenon is duo the tiny CM displacement current flowing through R2, which is out of the minimum measurement scope of the voltage probe. Therefore, the resistor with 50 Ω is impractical to be used in the proposed evaluation method. From Figure 14, it can be deduced that the 1# transformer has the best ability to suppress CM noise among the three kinds of the transformers.

CQ Verification
In Section 5.1, three kinds of transformers have been evaluated based on the proposed evaluation method. In this section, the following will use the previous method proposed in [18] to compare the difference between these two methods. Figure 17 shows the measurement results of the insertion loss of 1#, 2#, and 3# transformers. During the capacitive coupling frequency ranges, the transformer can be regarded as a pure capacitance to conduct CM displacement current and the slope of the insertion loss is 20 dB/Dec. For higher frequency range, the capacitive coupling and inductive coupling will make a difference to the insertion loss trace, simultaneously. For 1# transformer, its insertion loss is too small to be precisely measured in the capacitive coupling frequency range, so there is an oscillation in the low-frequency range. In order to calculate its effective capacitance, CQ, it is  Figure 13a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the signal generator outputs triangular signal assigned on two terminals of the primary winding. It can find that the triangular signal excitation has been distorted. This phenomenon is due to the power limitation of the signal generator. It is clear that the peak-to-peak value of the voltage in 1# transformer is the minimum and the peak-to-peak value of the voltage in 3# transformer is the maximum. As has been analyzed in Section 4, 1# transformer has the minimum value of C Q , which will lead to the lowest level of CM noise spectrum. However, there is a problem in waveform distortion of the signal source applied in primary winding, which may affect the precision of the evaluation method.
Similarly, Figure 14a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the sinusoidal signal is assigned on two terminals of the primary winding. The sinusoidal degree of the signal source is very well compared with that shown in Figure 13. The measurement results are the same as that of using the triangular signal and the sinusoidal signal source does not distort much. Figure 15a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the square signal is assigned on two terminals of the primary winding. It can clearly find that the square signal has distorted severely, which cause the voltage waveform on the sampling resistor to be no longer a standard rectangular wave. There are two peaks in the rising and falling edges of the voltage in R 2 .
Compared with the experiment results from Figures 13-15, the sinusoidal signal source has a minimum distortion degree. Hence, the sinusoidal signal source is recommended as an excitation source to be applied on the primary winding. Figure 16a-c shows the measurement results of the voltage waveform in sample resistor when the signal generator outputs sinusoidal signal assigned on two terminals of the primary winding. The resistor R 2 with 50 Ω is used. It is clear that the peak-to-peak values of the sample voltages in 1#, 2#, and 3# transformers are almost the same. As have been analyzed in Section 4, this phenomenon is duo the tiny CM displacement current flowing through R 2 , which is out of the minimum measurement scope of the voltage probe. Therefore, the resistor with 50 Ω is impractical to be used in the proposed evaluation method. Figure 15a-c shows the measurement voltage waveforms of the primary winding and the sampling resistor when the square signal is assigned on two terminals of the primary winding. It can clearly find that the square signal has distorted severely, which cause the voltage waveform on the sampling resistor to be no longer a standard rectangular wave. There are two peaks in the rising and falling edges of the voltage in R2.
Compared with the experiment results from Figures 13-15, the sinusoidal signal source has a minimum distortion degree. Hence, the sinusoidal signal source is recommended as an excitation source to be applied on the primary winding. Figure 16a-c shows the measurement results of the voltage waveform in sample resistor when the signal generator outputs sinusoidal signal assigned on two terminals of the primary winding. The resistor R2 with 50 Ω is used. It is clear that the peak-to-peak values of the sample voltages in 1#, 2#, and 3# transformers are almost the same. As have been analyzed in Section 4, this phenomenon is duo the tiny CM displacement current flowing through R2, which is out of the minimum measurement scope of the voltage probe. Therefore, the resistor with 50 Ω is impractical to be used in the proposed evaluation method. From Figure 14, it can be deduced that the 1# transformer has the best ability to suppress CM noise among the three kinds of the transformers. From Figure 14, it can be deduced that the 1# transformer has the best ability to suppress CM noise among the three kinds of the transformers.

C Q Verification
In Section 5.1, three kinds of transformers have been evaluated based on the proposed evaluation method. In this section, the following will use the previous method proposed in [18] to compare the difference between these two methods. Figure 17 shows the measurement results of the insertion loss of 1#, 2#, and 3# transformers. During the capacitive coupling frequency ranges, the transformer can be regarded as a pure capacitance to conduct CM displacement current and the slope of the insertion loss is 20 dB/Dec. For higher frequency range, the capacitive coupling and inductive coupling will make a difference to the insertion loss trace, simultaneously. For 1# transformer, its insertion loss is too small to be precisely measured in the capacitive coupling frequency range, so there is an oscillation in the low-frequency range. In order to calculate its effective capacitance, C Q , it is reasonable to regard it as a straight line in the low-frequency range. Then, using formula (11), the C Q of 1#, 2#, and 3# transformers are calculated as 0.2 pF, 1.8 pF, and 4 pF, respectively. The trend of calculation results conforms well with the evaluation results shown in Section 5.1. In order to further verify the effectiveness of the proposed transformer evaluation method, the following will measure the CM noise spectrums of three kinds of the transformers. reasonable to regard it as a straight line in the low-frequency range. Then, using formula (11), the CQ of 1#, 2#, and 3# transformers are calculated as 0.2 pF, 1.8 pF, and 4 pF, respectively. The trend of calculation results conforms well with the evaluation results shown in Section 5.1. In order to further verify the effectiveness of the proposed transformer evaluation method, the following will measure the CM noise spectrums of three kinds of the transformers.

Noise Spectrum Verification
In order to decouple EMI noise into CM noise and DM noise, the traditional measurement method is to use a noise separator, which is a voltage measurement method. However, the current measurement method is also feasible. For a better and clear understanding, the following will introduce how to use radio frequency (RF) current probe to separate the CM noise from the total EMI noise. Figure 18 shows the CM current measurement method. The CM current flowing through L and N lines are in the same direction. Therefore, using R & S EZ-17 radio frequency current probe can precisely measure the CM current and the measured signal can be transmitted into EMI receiver to be transformed into CM noise spectrum. The test environment is electromagnetic shielding chamber. EMI receiver is R & S ESCI and LISN is R & S ESH2-Z5.

Noise Spectrum Verification
In order to decouple EMI noise into CM noise and DM noise, the traditional measurement method is to use a noise separator, which is a voltage measurement method. However, the current measurement method is also feasible. For a better and clear understanding, the following will introduce how to use radio frequency (RF) current probe to separate the CM noise from the total EMI noise. Figure 18 shows the CM current measurement method. The CM current flowing through L and N lines are in the same direction. Therefore, using R & S EZ-17 radio frequency current probe can precisely measure the CM current and the measured signal can be transmitted into EMI receiver to be transformed into CM noise spectrum. The test environment is electromagnetic shielding chamber. EMI receiver is R & S ESCI and LISN is R & S ESH2-Z5.
introduce how to use radio frequency (RF) current probe to separate the CM noise from the total EMI noise. Figure 18 shows the CM current measurement method. The CM current flowing through L and N lines are in the same direction. Therefore, using R & S EZ-17 radio frequency current probe can precisely measure the CM current and the measured signal can be transmitted into EMI receiver to be transformed into CM noise spectrum. The test environment is electromagnetic shielding chamber. EMI receiver is R & S ESCI and LISN is R & S ESH2-Z5.  Figure 19a-b shows the EMI noise spectrums of the CM noise spectrum and the total EMI noise spectrum, respectively. In Figure 19a, the flyback converter with 1# transformer can achieve the lowest level of CM noise compared to the 2# transformer and 3# transformer. For higher frequency range (above 17 MHz), the CM noise attenuation effect is not so effective as in low-frequency range  Figure 19a-b shows the EMI noise spectrums of the CM noise spectrum and the total EMI noise spectrum, respectively. In Figure 19a, the flyback converter with 1# transformer can achieve the lowest level of CM noise compared to the 2# transformer and 3# transformer. For higher frequency range (above 17 MHz), the CM noise attenuation effect is not so effective as in low-frequency range due to the complex effects of the parasitic parameter. As shown in Figure 17, the transformer in capacitive and inductive coupling frequency range cannot be regarded as a pure capacitance to conduct CM noise. This is an essential reason for high-frequency CM noise that not easy to be suppressed. In Figure 19b, the reason why the attenuation effect of the EMI noise in the lower frequency range (below 500 kHz) is not so evident is that the EMI noise can be decoupled as CM noise and DM noise. Usually, CM noise contributes more in the higher frequency range, and DM noise also plays a major role in lower frequency range. Transformer winding design can only attenuate the CM noise flowing through transformer coupling path, which has nothing to do with the DM noise attenuation. The proposed method can effectively evaluate the CM noise behavior of the transformer, which is helpful to pass the EMI standard limited line EN55022 Class B. Figure 20a,b shows the CM noise flowing direction in transformer coupling path when the static points of the primary and secondary winding are shorted together. It can find the CM noise in transformer coupling path will not flow to the ground and be detected by LISN. Hence, this method can verify whether the CM noise has been totally eliminated. This method is impractical to be used in an actual product as this method will make the transformer lose isolation function. Figure 21 shows the CM noise spectrums when the static points of 1# transformer are shorted. For this situation, the CM current flowing through transformer coupling path will circulate internally instead of being detected by LISN and the measured CM noise spectrums can verify whether the transformer is well designed. It can find that the CM noise spectrum with 1# transformer is almost the same as that with shorting the static points. For this experiment result, it can prove that 1# transformer evaluated by the proposed method has a minimal peak to peak value of the voltage shown in Figure 14. Besides, it also can achieve near zero CM noise flowing through transformer coupling path. frequency range (below 500 kHz) is not so evident is that the EMI noise can be decoupled as CM noise and DM noise. Usually, CM noise contributes more in the higher frequency range, and DM noise also plays a major role in lower frequency range. Transformer winding design can only attenuate the CM noise flowing through transformer coupling path, which has nothing to do with the DM noise attenuation. The proposed method can effectively evaluate the CM noise behavior of the transformer, which is helpful to pass the EMI standard limited line EN55022 Class B.  Figure 20a,b shows the CM noise flowing direction in transformer coupling path when the static points of the primary and secondary winding are shorted together. It can find the CM noise in transformer coupling path will not flow to the ground and be detected by LISN. Hence, this method can verify whether the CM noise has been totally eliminated. This method is impractical to be used in an actual product as this method will make the transformer lose isolation function. Figure 21 shows the CM noise spectrums when the static points of 1# transformer are shorted. For this situation, the CM current flowing through transformer coupling path will circulate internally instead of being detected by LISN and the measured CM noise spectrums can verify whether the transformer is well designed. It can find that the CM noise spectrum with 1# transformer is almost the same as that with shorting the static points. For this experiment result, it can prove that 1# transformer evaluated by the proposed method has a minimal peak to peak value of the voltage shown in Figure 14. Besides, it also can achieve near zero CM noise flowing through transformer coupling path. The resistor R2 with 10k Ω is recommended to sample the CM voltage in the proposed method.

Conclusions
This paper proposes a general transformer CM noise behavior evaluation method. Only a signal generator and an oscilloscope can come close to achieving the same evaluation effects as in previous references.
This evaluation method has multiple benefits: 1. The measurement instruments are cheaper compared with professional EMI measurement instruments, and many transformer manufactures can easily use this evaluation method. 2. The evaluation method can put the voltage potential distribution of the primary and secondary winding into consideration, which can reflect the CM noise behavior of the transformer.
There are some key parts that should be pointed out: 3. The resistance of R2 should be chosen appropriately. 4. The voltage potential difference between the primary ground and the secondary ground can make a difference to the lumped equivalent CM noise capacitance of the transformer. 5. Sinusoidal signal source is recommended as an excitation to be applied on the primary winding. 6. The proposed evaluation method can effectively evaluate the CM noise behaviors of transformer only in capacitive coupling frequency range.