Patents Analysis of Thermal Bridges in Slab Fronts and Their Effect on Energy Demand

Nowadays, the building sector is one of the main sources emitting pollutant gases to the atmosphere due to its deficient energy behaviour. Among the elements of the envelope, the thermal bridges are where the heat losses and gains mainly occur, depending on the season of the year. To reduce the effect of the thermal bridges, there are different patented technologies which give provide solutions. In this paper, the thermal behaviour of five patented slab front (slab-façade) thermal bridges are analysed in a case study located in the south of Spain. Moreover, the influence of the thermal bridge on the energy demand from the building analysed was evaluated, both in the current scenario and future ones (2020, 2050 and 2080). The results reveal that the use of the patents in slab fronts can mean reductions by up to 95.74% in the linear thermal transmittance. Likewise, due to the improvement of the thermal bridge of slab fronts by using the patented designs which offered the best features, a savings in the global energy demand for heating higher than 18% as well as a savings in the global energy demand for cooling higher than 2.80% could be achieved in all the time scenarios considered.


Introduction
The energy consumption of buildings is causing serious consequences for the environment. In 2014, the building sector was responsible for 24.79% of the energy consumption in the European Union [1]. Furthermore, this sector tends to produce a higher energy consumption per year (it has been causing an annual increase of 1% since 1990) [2]. In order to reduce the energy consumption from the existing building stock, the European Union has developed the roadmap for a low-carbon economy [3]. The objective pursued by this research is to reduce the pollutant gas emissions by 80% by 2050. For this purpose, the building sector should reduce the pollutant gas emissions by 90% by cutting down its energy consumption. Thus, one of the main challenges of today´s society is the energy modernization of the existing building stock as well as the design of new efficient buildings, mainly to guarantee an adequate behaviour of the buildings in future climate scenarios [4,5].
Among the different elements which compose the building, the envelope is among those which has a more significant effect on energy behaviour [6][7][8]. Highly efficient thermophysical properties for the envelope allow one to significantly reduce the energy demand of buildings [9]. This envelope is normally constituted by a series of layers of different thicknesses and thermal conductivities which determine its thermal transmittance. However, there are areas of the envelope where the junction of different elements causes a thermal bridge. Thermal bridge is understood as the part of the envelope which shows variations in the thermal resistance due to factors such as the presence of materials with a Recent studies [37][38][39] have analysed thermal bridges generated by lightweight steel-framed (LSF) walls due to the high thermal conductivity of the steel studs. Santos et al. [37] studied the importance of the flaking heat loss in LSF walls, determining that the thermal transmittance can vary from −22% for the external surface to +50% for the internal surface, and the metal fixation elements are one of the most important elements. The use of mitigation techniques, such as thermal break strips and slotted steel profiles, could lead to reduce the thermal transmittance by 8.3% [38]. In a later study [39], the authors evaluated the effectiveness of the position of thermal insulation in LSF walls by analysing three different types of construction (cold, warm, and hybrid construction). The results determined that the warm construction (insulation from the exterior) is the typology of LSF walls less affected by the thermal bridge.
Levinskyte, Banionis and Geleziunas [40] analysed the importance of thermal bridges in highly efficient buildings in Lithuania, and the heat losses between the walls and the slab were among the most important joints. The junction between the slabs and the façades are one of the most complicated junctions in order to decrease the thermal bridge, since these junctions are consolidated building elements that should be studied during the design phase to be able to cause efficient constructive solutions. To do this, there are nowadays different patents proposing construction solutions to reduce the heat losses of thermal bridges in slab fronts. However, there are no studies where the efficiency of such patents is analysed.
The previous review reveals the importance of decreasing scientifically the heat losses through thermal bridges due to their influence on the energy behaviour of the building. However, there are no studies where the existing patents to reduce heat losses or gains through thermal bridges have been profoundy analysed. Thus, the objective of this work was to analyse the thermal behaviour of some existing patents describing construction solutions for slab fronts, focusing on these junctions due to their significant influence on heat losses through the façade [40]. For this purpose, five different solutions were chosen and applied on a real case study. The heat transfer for the five patented designs was analysed by two-dimensional calculation using the THERM software, and both the value of linear thermal transmittance and the temperature factor for the interior surface were obtained, thus identifying the patent with the best behaviour. Likewise, the effect that the best patent had on the energy behaviour of a building was studied, both in current and future scenarios with the effect of the climate change (2020,2050,2080). To do this, energy simulations were carried out using the Design Builder software (which includes the Energy Plus calculation engine) by introducing the value of linear thermal transmittance obtained by the patent with the best thermal behaviour.

Patents Studied
To analyse the thermal bridges, five patents of constructive solutions of thermal bridges different in design, materials and work execution were chosen. The patents considered are listed below and ordered by year of publication (see Figure 1): Patent 1 consists of the creation of a formwork lost for the slab by creating a box made by metal panels where an insulating material is placed. Unlike other patents described below, the external masonry leaf does not present discontinuities along the surface, so the thickness of the insulating material is limited by this design condition. Patent 2 proposes a constructive solution similar to that from Patent 1, but metal panels are not used in this case. This patent consists of a thermal insulation panel joined to the slab by a metal bar frame. Patent 3 consists of introducing an insulating material membrane of multiple reflector type in both all the slab front and inferior and superior overlapping, as well as a plaster panel.
Patent 4 is similar to Patent 3. The design consists of putting a covering membrane in both slab front and some part of its inferior and superior sides. This covering membrane is constituted by two layers of polyethylene and an aluminium membrane.
Finally, the last patent studied (Patent 5) is an evolution of Patent 2. This construction solution consists of a metal structure of bars with thermal insulation fixed to the perimeter beams before concreting, using an insulating material: extruded polystyrene (XPS) or polyurethane (PUR), with a thickness between 20 and 60 mm. Finally, the last patent studied (Patent 5) is an evolution of Patent 2. This construction solution consists of a metal structure of bars with thermal insulation fixed to the perimeter beams before concreting, using an insulating material: extruded polystyrene (XPS) or polyurethane (PUR), with a thickness between 20 and 60 mm.

Analysed Building
The building chosen is a typical building from the south of Spain, built in 2008. The building has a height of three floors over the building line and the bulkhead. There are six dwellings: two on the ground floor, two on the first floor, and two on the second floor (see Figure 2). The northern and southern side walls have no windows and are the dividing walls with respect to the adjacent buildings. The main façade faces West. There are also two courtyards: an interior courtyard allowing the opening of windows in the most internal areas, and an exterior courtyard in the eastern façade, which is only available for the dwellings on the ground floor.
The building was chosen because it was a typical building of the area and had thermal bridge problems (see Figure 3). Moreover, technical documentation was available to characterize it correctly. Thus, the composition of the façade was determined following the methodology established by Ficco

Analysed Building
The building chosen is a typical building from the south of Spain, built in 2008. The building has a height of three floors over the building line and the bulkhead. There are six dwellings: two on the ground floor, two on the first floor, and two on the second floor (see Figure 2). The northern and southern side walls have no windows and are the dividing walls with respect to the adjacent buildings. The main façade faces West. There are also two courtyards: an interior courtyard allowing the opening of windows in the most internal areas, and an exterior courtyard in the eastern façade, which is only available for the dwellings on the ground floor.
Energies 2018, 11, 2222 5 of 18 et al. [46] of using reliable technical documentation. Table 1 indicates the relationship of layers that constitute the façade as well as their thermophysical properties. . Figure 3. Thermographies of the analysed building carried out according to the ISO standard 6781 [47].

Climate Zone
The building is situated in Seville, in the south of Spain. The city is located in the Csa climate zone [49], characterized by dry and hot summers as well as mild winters, where the maximum temperature during the heating season can reach 36 °C, and the average temperature in winter is 10 °C (see Table 2). The building was chosen because it was a typical building of the area and had thermal bridge problems (see Figure 3). Moreover, technical documentation was available to characterize it correctly. Thus, the composition of the façade was determined following the methodology established by Ficco et al. [46] of using reliable technical documentation. Table 1 indicates the relationship of layers that constitute the façade as well as their thermophysical properties. et al. [46] of using reliable technical documentation. Table 1 indicates the relationship of layers that constitute the façade as well as their thermophysical properties. . Figure 3. Thermographies of the analysed building carried out according to the ISO standard 6781 [47].

Climate Zone
The building is situated in Seville, in the south of Spain. The city is located in the Csa climate zone [49], characterized by dry and hot summers as well as mild winters, where the maximum temperature during the heating season can reach 36 °C, and the average temperature in winter is 10 °C (see Table 2).  et al. [46] of using reliable technical documentation. Table 1 indicates the relationship of layers that constitute the façade as well as their thermophysical properties. . Figure 3. Thermographies of the analysed building carried out according to the ISO standard 6781 [47].

Climate Zone
The building is situated in Seville, in the south of Spain. The city is located in the Csa climate zone [49], characterized by dry and hot summers as well as mild winters, where the maximum temperature during the heating season can reach 36 °C, and the average temperature in winter is 10 °C (see Table 2).

Climate Zone
The building is situated in Seville, in the south of Spain. The city is located in the Csa climate zone [49], characterized by dry and hot summers as well as mild winters, where the maximum temperature during the heating season can reach 36 • C, and the average temperature in winter is 10 • C (see Table 2).

Virtual Modelling
As mentioned previously, the modelling of the thermal bridges was carried out by using the THERM software. Six configurations were modelled as follows: (i) construction section that the building currently has; (ii) construction section with Patent 1; (iii) construction section with Patent 2; (iv) construction section with Patent 3; (v) construction section with Patent 4; and (vi) construction section with Patent 5. The thermophysical properties indicated in the project were used as thermophysical properties of the materials of the constructive solution. Internal and external conditions were defined from the long-term monitoring of the building (see Figure 4). Measurements were performed in the living room on the first floor. Based on the monitoring, it was determined that the maximum temperature differences obtained were of 10 • C. For this reason, an indoor temperature of 20 • C and an outdoor temperature of 10 • C were defined in the simulations made by THERM.

Virtual Modelling
As mentioned previously, the modelling of the thermal bridges was carried out by using the THERM software. Six configurations were modelled as follows: (i) construction section that the building currently has; (ii) construction section with Patent 1; (iii) construction section with Patent 2; (iv) construction section with Patent 3; (v) construction section with Patent 4; and (vi) construction section with Patent 5. The thermophysical properties indicated in the project were used as thermophysical properties of the materials of the constructive solution. Internal and external conditions were defined from the long-term monitoring of the building (see Figure 4). Measurements were performed in the living room on the first floor. Based on the monitoring, it was determined that the maximum temperature differences obtained were of 10 °C. For this reason, an indoor temperature of 20 °C and an outdoor temperature of 10 °C were defined in the simulations made by THERM. As the THERM software has been validated according to the standard EN ISO 10211 in several studies [39,50,51], the aim of verifying the models developed using THERM was the determination of the possible differences in the inputs from the model as well as the thermophysical properties of the materials. To do this, two-dimensional simulations of the same thermal bridges were carried out by the HTFlux software, using the same boundary conditions and material properties (see Figure 5), and the average values of thermal transmittance obtained were compared. As the THERM software has been validated according to the standard EN ISO 10211 in several studies [39,50,51], the aim of verifying the models developed using THERM was the determination of the possible differences in the inputs from the model as well as the thermophysical properties of The modelling of the building was performed by using the EPW file from the Design Builder software for the city of Seville. To obtain the climate scenarios for the years 2020, 2050 and 2080, a morphing process was carried out [52][53][54]. The CCWorldWeatherGen software was used to perform the morphing process [54]. This morphing process [52][53][54] uses the meteorological data of the EPW files with United Kingdom Met Office Hadley Centre general circulation model (GCM) predictions for the A2 scenario (intermediate-high) of greenhouse gas emissions effects [55], generating time series for 2020, 2050, and 2080. For this, the morphing process uses three different algorithms depending on the variable to be modified. These algorithms are widely described by Belcher et al. [52].
There are studies where the importance of using the morphing process to obtain future scenarios is shown [4,5,52,54], since these scenarios are generated by using a current meteorological dataset, although extraordinary natural phenomena associated with the climate change (hurricanes or storms) are not considered [4].
Thus, when the morphing process was finished, three EPW files from the city of Seville were generated with the modified climate variables under A2 emissions scenario for the years 2020, 2050, and 2080.
By using these four climate scenarios (current, 2020, 2050, and 2080), eight different cases of energy simulation (see Table 3) could be established on the model of the building carried out using Design Builder (see Figure 6).  The modelling of the building was performed by using the EPW file from the Design Builder software for the city of Seville. To obtain the climate scenarios for the years 2020, 2050 and 2080, a morphing process was carried out [52][53][54]. The CCWorldWeatherGen software was used to perform the morphing process [54]. This morphing process [52][53][54] uses the meteorological data of the EPW files with United Kingdom Met Office Hadley Centre general circulation model (GCM) predictions for the A2 scenario (intermediate-high) of greenhouse gas emissions effects [55], generating time series for 2020, 2050, and 2080. For this, the morphing process uses three different algorithms depending on the variable to be modified. These algorithms are widely described by Belcher et al. [52].
There are studies where the importance of using the morphing process to obtain future scenarios is shown [4,5,52,54], since these scenarios are generated by using a current meteorological dataset, although extraordinary natural phenomena associated with the climate change (hurricanes or storms) are not considered [4].
Thus, when the morphing process was finished, three EPW files from the city of Seville were generated with the modified climate variables under A2 emissions scenario for the years 2020, 2050, and 2080.
By using these four climate scenarios (current, 2020, 2050, and 2080), eight different cases of energy simulation (see Table 3) could be established on the model of the building carried out using Design Builder (see Figure 6).  In all simulated cases, the rest of the building model parameters, such as use profiles or HVAC systems, were not modified. In this sense, it is important to highlight the configured parameters regarding the use profiles, the efficiency of cooling and heating systems, air turnovers, and internal heat gains.
The use profile was defined with a percentage between 50% and 100%, except during working hours (from 7:00 a.m. to 3:00 p.m.) in which a use of 10% was established. Due to the climate conditions of the area, heating and cooling systems were considered to be used in atypical months (e.g. using cooling in cold months if the set point temperatures are exceeded). For the cooling, the set point temperature was of 25 °C and the setback temperature of 27 °C, whereas for the heating, the set point temperature was of 20 °C and the setback temperature of 17 °C. The heating system had a Coefficient of Performance (CoP) of 0.85, and the cooling system had a CoP of 1.80.
With respect to the ventilation rate, the use profiles used where those established by the technical standard in Spain [56]. The number of air changes per hour for all the year was 0.63 ac/h by means of mechanical ventilation. The only exception corresponded to summer, between 1:00 and 8:00 a.m., since the technical standard established that ventilation should be natural (due to the opening of the windows) and the rate to be used should be of 4.00 ac/h in that period.
For the internal heat gains, the use profile of lightning systems was established, as well as the equipment in the house established by the technical standard in Spain, with a density of maximum power of 4.4 W/m 2 . The metabolic rate of the occupants was defined according to what it is indicated in Table 5 of chapter 8 in the ASHRAE Handbook of Fundamentals [57].

Patent Analysis of Thermal Bridges of Slab Fronts
The simulation of the patents using THERM allowed us to prove the improvements produced by the different constructive solutions. Firstly, the representation of the models generated by THERM was determined. To do this, the existing differences between the thermal transmittance values obtained by both software for each construction solution were analysed. As can be appreciated in Table 4, the thermal transmittance results obtained for each construction solution presented deviations of less than 4.5%, and these differences were due to the possibility of configuration of the materials that both software allowed. Thus, as big differences between both simulations were not obtained, the models of the construction solutions carried out using THERM were representative.  In all simulated cases, the rest of the building model parameters, such as use profiles or HVAC systems, were not modified. In this sense, it is important to highlight the configured parameters regarding the use profiles, the efficiency of cooling and heating systems, air turnovers, and internal heat gains.
The use profile was defined with a percentage between 50% and 100%, except during working hours (from 7:00 a.m. to 3:00 p.m.) in which a use of 10% was established. Due to the climate conditions of the area, heating and cooling systems were considered to be used in atypical months (e.g., using cooling in cold months if the set point temperatures are exceeded). For the cooling, the set point temperature was of 25 • C and the setback temperature of 27 • C, whereas for the heating, the set point temperature was of 20 • C and the setback temperature of 17 • C. The heating system had a Coefficient of Performance (CoP) of 0.85, and the cooling system had a CoP of 1.80.
With respect to the ventilation rate, the use profiles used where those established by the technical standard in Spain [56]. The number of air changes per hour for all the year was 0.63 ac/h by means of mechanical ventilation. The only exception corresponded to summer, between 1:00 and 8:00 a.m., since the technical standard established that ventilation should be natural (due to the opening of the windows) and the rate to be used should be of 4.00 ac/h in that period.
For the internal heat gains, the use profile of lightning systems was established, as well as the equipment in the house established by the technical standard in Spain, with a density of maximum power of 4.4 W/m 2 . The metabolic rate of the occupants was defined according to what it is indicated in Table 5 of chapter 8 in the ASHRAE Handbook of Fundamentals [57].

Patent Analysis of Thermal Bridges of Slab Fronts
The simulation of the patents using THERM allowed us to prove the improvements produced by the different constructive solutions. Firstly, the representation of the models generated by THERM was determined. To do this, the existing differences between the thermal transmittance values obtained by both software for each construction solution were analysed. As can be appreciated in Table 4, the thermal transmittance results obtained for each construction solution presented deviations of less than 4.5%, and these differences were due to the possibility of configuration of the materials that both software allowed. Thus, as big differences between both simulations were not obtained, the models of the construction solutions carried out using THERM were representative. After validating the representation of the models generated by THERM, linear thermal transmittance results of the different patents were obtained. To obtain the linear thermal transmittance (Equation (1)), the software provides the factor of thermal coupling (Equation (2)), which is fundamental to calculate the linear thermal transmittance: where ψ is the linear thermal transmittance (W/(m·K)); L 2D is the factor of two-dimensional coupling (W/(m·K)); l j is the length of the two-dimensional geometric model (m); U j is the thermal transmittance of the one-dimensional component j (W/(m 2 ·K)); T in is the indoor air temperature (K); and T out is the outdoor air temperature (K). In Figure 7, the values of linear thermal transmittance obtained for each simulated building configuration are represented. As can be proved, the results showed how the linear thermal transmittance decreased using almost all the patents considered. In this sense, Patent 5 was the one which obtained the lowest linear thermal transmittance, a decrease by 95.74% with respect to the construction solution without slab front. The other solutions obtained lower improvements than Patent 5: Patent 1 achieved a decrease by 20.06% with respect to the case study without patent; Patent 2 achieved a decrease by 80.40%, being the patent with the second best results; Patent 3 obtained a decrease by 36.32%. Only Patent 4 obtained a higher linear thermal transmittance than the case study without patent, with an increase by 3.50%. This is because this patent did not use an insulating material, since it only included polyethylene (with a thermal conductivity of 0.33 W/(m·K)) and aluminium (with a thermal conductivity of 230 W/(m·K)). Thus, the combination of both materials made the linear thermal transmittance obtainedhigher than that from the study assumption without modification. After validating the representation of the models generated by THERM, linear thermal transmittance results of the different patents were obtained. To obtain the linear thermal transmittance (Equation (1)), the software provides the factor of thermal coupling (Equation (2)), which is fundamental to calculate the linear thermal transmittance: where is the linear thermal transmittance (W/(m·K)); 2 is the factor of two-dimensional coupling (W/(m·K)); is the length of the two-dimensional geometric model (m); is the thermal transmittance of the one-dimensional component j (W/(m 2 ·K)); is the indoor air temperature (K); and is the outdoor air temperature (K). In Figure 7, the values of linear thermal transmittance obtained for each simulated building configuration are represented. As can be proved, the results showed how the linear thermal transmittance decreased using almost all the patents considered. In this sense, Patent 5 was the one which obtained the lowest linear thermal transmittance, a decrease by 95.74% with respect to the construction solution without slab front. The other solutions obtained lower improvements than Patent 5: Patent 1 achieved a decrease by 20.06% with respect to the case study without patent; Patent 2 achieved a decrease by 80.40%, being the patent with the second best results; Patent 3 obtained a decrease by 36.32%. Only Patent 4 obtained a higher linear thermal transmittance than the case study without patent, with an increase by 3.50%. This is because this patent did not use an insulating material, since it only included polyethylene (with a thermal conductivity of 0.33 W/(m·K)) and aluminium (with a thermal conductivity of 230 W/(m·K)). Thus, the combination of both materials made the linear thermal transmittance obtainedhigher than that from the study assumption without modification. Furthermore, the surface temperature factor ( , ) (Equation (3)) was determined by the simulation carried out by THERM to analyse the possibility of condensation generated inside the building. For this purpose, the internal surface temperature ( , ) of each construction solution was measured in the point with the lowest temperature thanks to the isotherm profiles generated in each simulation (see Figure 8). Furthermore, the surface temperature factor ( f R,si ) (Equation (3)) was determined by the simulation carried out by THERM to analyse the possibility of condensation generated inside the building. For this purpose, the internal surface temperature (T s,in ) of each construction solution was measured in the point with the lowest temperature thanks to the isotherm profiles generated in each simulation (see Figure 8).  Figure 8 shows that the point with the lowest temperature (the joint between the inferior side of the slab and the façade) was the same for all the building configurations considered. The results reflected slight variations in the factor , for the different construction solutions. The construction solution without patent obtained a temperature factor of 0.865, which exceeded the minimum value required by the technical standard in Spain for the climate region of Seville (0.52) [56]. The remaining patents obtained the same or higher values of factor , , so all the analysed building configurations did not cause condensations (see Figure 9). The patent with the best factor , was Patent 5 with a  Figure 8 shows that the point with the lowest temperature (the joint between the inferior side of the slab and the façade) was the same for all the building configurations considered. The results reflected slight variations in the factor f R,si for the different construction solutions. The construction solution without patent obtained a temperature factor of 0.865, which exceeded the minimum value required by the technical standard in Spain for the climate region of Seville (0.52) [56]. The remaining patents obtained the same or higher values of factor f R,si , so all the analysed building configurations did not cause condensations (see Figure 9). The patent with the best factor f R,si was Patent 5 with a value of 0.925, followed by Patents 2 and 3 with factors of 0.905 and 0.915, respectively. As similarly occurred for the linear thermal transmittance, Patent 4 obtained the same factor f R,si as for the constructive solution without patent, so its design did not influence the decrease of condensation risk. Therefore, among the different patents analysed, Patent 5 had best features in the case study analysed, since this patent achieved the lowest linear thermal transmittance as well as the best temperature factor for the interior surface: Energies 2018, 11, 2222 11 of 18 value of 0.925, followed by Patents 2 and 3 with factors of 0.905 and 0.915, respectively. As similarly occurred for the linear thermal transmittance, Patent 4 obtained the same factor , as for the constructive solution without patent, so its design did not influence the decrease of condensation risk. Therefore, among the different patents analysed, Patent 5 had best features in the case study analysed, since this patent achieved the lowest linear thermal transmittance as well as the best temperature factor for the interior surface: Figure 9. Internal surface temperature factor in all the assumptions. The minimum factor , required by the technical standard in Spain is represented by black line.

Influence of Thermal Bridge of the Slab Front on Energy Demand
After determining the patent with best results in the building analysed, its influence on the energy demand was studied. For this purpose, and as mentioned in Section 3.3, eight different simulations were carried out: four corresponding to the building without patent, and four to the building with the best patent, aiming at assessing the effects of climate change on the energy demand of the building. In Figure 10, the values of heating and cooling demand obtained for each simulation (building with and without patent) are represented. Regarding the analysis generated by using the EPW files for the different time scenarios (current, 2020, 2015, and 2018), the increase of external temperatures in the different time scenarios caused the decrease of the heating energy demand, reaching decreases higher than 1000 kWh, and even removing the heating demand in future scenarios (June and September of 2050 and 2080) with respect to the current scenario. On the other hand, the increase of external temperatures led to increasing the cooling energy demand in the different simulations, with an increase by 82.03% in July, and by 74.54% in August of 2080 with respect to the values obtained in the current scenario.
The use of the building patent allowed to reduce the energy demand of the building in all the scenarios considered (see Figure 10). In Tables 5-8, the values obtained of energy demand for the different periods considered as well as the percentage deviations are indicated. As can be appreciated, the effect generated by the building patent on the monthly energy demand depends on the type of demand: the heating energy demand was more influenced by the effect of the thermal bridge than the cooling energy demand. In this sense, the energy demand for heating in the current scenario could be reduced up to 15.44% during the months characterized by lower temperatures in the region (January, February and December), with a maximum decrease of 325.25 kWh for January, whereas the energy demand for cooling had a maximum difference of 227.14 kWh. Moreover, the percentage deviation on the heating demand could be quite significant in the less cold months, since the deviation obtained was higher because the energy demand was lower, even achieving the full removal of the heating demand. Likewise, the energy demand for cooling presented a percentage deviation which oscillated around 3% in each of the months.

Influence of Thermal Bridge of the Slab Front on Energy Demand
After determining the patent with best results in the building analysed, its influence on the energy demand was studied. For this purpose, and as mentioned in Section 3.3, eight different simulations were carried out: four corresponding to the building without patent, and four to the building with the best patent, aiming at assessing the effects of climate change on the energy demand of the building. In Figure 10, the values of heating and cooling demand obtained for each simulation (building with and without patent) are represented. Regarding the analysis generated by using the EPW files for the different time scenarios (current, 2020, 2015, and 2018), the increase of external temperatures in the different time scenarios caused the decrease of the heating energy demand, reaching decreases higher than 1000 kWh, and even removing the heating demand in future scenarios (June and September of 2050 and 2080) with respect to the current scenario. On the other hand, the increase of external temperatures led to increasing the cooling energy demand in the different simulations, with an increase by 82.03% in July, and by 74.54% in August of 2080 with respect to the values obtained in the current scenario.
The use of the building patent allowed to reduce the energy demand of the building in all the scenarios considered (see Figure 10). In Tables 5-8, the values obtained of energy demand for the different periods considered as well as the percentage deviations are indicated. As can be appreciated, the effect generated by the building patent on the monthly energy demand depends on the type of demand: the heating energy demand was more influenced by the effect of the thermal bridge than the cooling energy demand. In this sense, the energy demand for heating in the current scenario could be reduced up to 15.44% during the months characterized by lower temperatures in the region (January, February and December), with a maximum decrease of 325.25 kWh for January, whereas the energy demand for cooling had a maximum difference of 227.14 kWh. Moreover, the percentage deviation on the heating demand could be quite significant in the less cold months, since the deviation obtained was higher because the energy demand was lower, even achieving the full removal of the heating demand. Likewise, the energy demand for cooling presented a percentage deviation which oscillated around 3% in each of the months.     Regarding the future scenarios, the effect generated by the patented building solution on the heating demand was decreasing, with values of monthly maximum differential of 285.87 kWh for 2020, 241.04 kWh for 2050, and 197.68 kWh for 2080. This was due to the decrease of heating demand caused by the increase of the external temperatures. However, the use of the building patent in the simulation allowed reductions up to 21.36% for the coldest months, so although its influence is lower in future scenarios, the energy demand for heating is being reduced considerably. On the other hand, the maximum decrease in cooling demand that generated the improvement of the thermal bridge allowed one to achieve monthly maximum reductions of 315.33 kWh for 2020, 414.72 kWh for 2050, and 513.77 kWh for 2080.
Therefore, the effect of the patent for improving the thermal bridge of the slab front on the global energy demand of the building was quite significant. Figure 11 represents the global energy demands for heating and cooling, as well as the total demand for each assumption studied. As it can be seen, the decrease obtained in the heating demand was very significant, even in future scenarios characterized by less heating demand. In this sense, the decrease achieved by year was of 18.83% in 2020, 19.78% in 2050, and 21.43% in 2080. On the other hand, the global decrease in cooling demand had the same rate of percentage decrease for all the scenarios considered, varying between 2.80% for the current scenario and 3.20% for the scenario in 2080. Thus, the improvement of the thermal bridge of the slab front allowed to reduce the energy demand of the building in the different scenarios considered, with a saving on the heating energy demand higher than 18%, and on the cooling energy demand higher than 2.80%. Regarding the future scenarios, the effect generated by the patented building solution on the heating demand was decreasing, with values of monthly maximum differential of 285.87 kWh for 2020, 241.04 kWh for 2050, and 197.68 kWh for 2080. This was due to the decrease of heating demand caused by the increase of the external temperatures. However, the use of the building patent in the simulation allowed reductions up to 21.36% for the coldest months, so although its influence is lower in future scenarios, the energy demand for heating is being reduced considerably. On the other hand, the maximum decrease in cooling demand that generated the improvement of the thermal bridge allowed one to achieve monthly maximum reductions of 315.33 kWh for 2020, 414.72 kWh for 2050, and 513.77 kWh for 2080.
Therefore, the effect of the patent for improving the thermal bridge of the slab front on the global energy demand of the building was quite significant. Figure 11 represents the global energy demands for heating and cooling, as well as the total demand for each assumption studied. As it can be seen, the decrease obtained in the heating demand was very significant, even in future scenarios characterized by less heating demand. In this sense, the decrease achieved by year was of 18.83% in 2020, 19.78% in 2050, and 21.43% in 2080. On the other hand, the global decrease in cooling demand had the same rate of percentage decrease for all the scenarios considered, varying between 2.80% for the current scenario and 3.20% for the scenario in 2080. Thus, the improvement of the thermal bridge of the slab front allowed to reduce the energy demand of the building in the different scenarios considered, with a saving on the heating energy demand higher than 18%, and on the cooling energy demand higher than 2.80%.

Conclusions
This article studies the effect of the thermal bridge of slab front on the energy demand of a building. Firstly, five patented construction solutions for thermal bridges in slab fronts in a certain case study were analysed by means of two-dimensional simulation, determining the best patent solution for the building. Then, energy simulations of the case study in different time scenarios

Conclusions
This article studies the effect of the thermal bridge of slab front on the energy demand of a building. Firstly, five patented construction solutions for thermal bridges in slab fronts in a certain case study were analysed by means of two-dimensional simulation, determining the best patent solution for the building. Then, energy simulations of the case study in different time scenarios (current, 2020, 2050 and 2080) were carried out by analysing the effect of improving the thermal bridge in the slab front on the energy demand of the building. Based on the results obtained, the following conclusions can be drawn:

•
From the five patents analysed, the one which obtained the lowest linear thermal transmittance (ψ) was Patent 5, with a reduction of 95.74% with respect to the linear thermal transmittance that the slab front of the analysed building presents. The rest of the patents obtained lower decreases, and even a higher linear thermal transmittance was obtained by Patent 4.

•
The temperature factor for the interior surface ( f R,si ) for both constructive solution of the case study and the different patents analysed exceeded the value required by the estate rules which guaranteed that condensations were not generated. Thus, the climate conditions typical of the analysis region (Csa classification according to Köppen-Geiger) allowed to guarantee a low condensation risk due to the thermal bridges of the slab fronts.

•
The improvement of the thermal bridge in the slab front allowed to achieve important decreases on the heating demand in the current scenario, with differences up to 325.25 kWh during the month of the highest demand. Regarding the cooling energy demand, the change generated by the improvement of the thermal bridge was lower, although reductions by 227.14 kWh were obtained in the summer months. • For future scenarios, the effect generated by the increase of the outdoor temperatures with a lower heating demand and a higher cooling demand affected the incidence of the improvement of the thermal bridge on the energy behaviour of the building. In this sense, the monthly reduction of the heating energy demand generated by the improvement of the thermal bridge presented a decreasing behaviour, with the following values of maximum decrease: 285.87 kWh (2020) On the other hand, the cooling demand presented a growing tendency in the monthly maximum decreases in the different scenarios analysed, with maximum decreases of 315.33 kWh in 2020, 414.72 kWh in 2050, and 513.77 kWh in 2080.
Therefore, the improvement of the thermal bridge of the slab front by using the best patent analysed led to global reductions on the energy demand for heating higher than 18%, whereas on the energy demand for cooling were higher than 2.80% in all the time scenarios considered.
To conclude, it is important to highlight that there are no studies where the thermal behaviour of different patented designs for thermal bridges in slab fronts is studied, as well as the effect that these solutions havee on the energy demand of the building, both in current and future scenarios. In this sense, despite the progressive reduction of heating demand and the increase of cooling demand, the improvement of the thermal bridge of the slab front allows one to reduce significantly the energy demand of the building. Thus, this is an aspect that should be considered in both design phase and energy audits of the existing buildings, with the aim of guaranteeing an adequate energy behaviour of the building.
Author Contributions: All authors took part in the choice of the case studies, performed the measurement, managed and analysed data, and wrote the document.
Funding: This research received no external funding.