Autoignition Behavior of an Ethanol-Methylcellulose Gel Droplet in a Hot Environment

Autoignition of an ethanol-based gel droplet was experimentally investigated by adding 10 wt % of methylcellulose as gellant to liquid ethanol. Experimental studies of the ignition behavior of the gel droplet were found to be quite rare. The initial droplet diameter was 1.17 ± 0.23 mm. The gel droplet was suspended on a K-type thermocouple and its evaporation, ignition and combustion characteristics were evaluated and compared with pure ethanol at an ambient temperature of 600, 700, and 800 ◦C under atmospheric pressure conditions. The gel droplet exhibited swelling and vapor jetting phenomena. Before ignition, a linear decrease in droplet diameter followed by a sudden increase was repeatedly observed, which was caused by evaporation and swelling processes, respectively. Major droplet swelling was detected just before the onset of ignition at all temperatures. But no further swelling was detected after ignition. For the gel droplet, the ignition delay accounted for 93% of the droplet lifetime at 600 ◦C, and 88% at 700 ◦C, but only 31% at 800 ◦C. Its average burning rate was also evaluated for all temperatures. At 800 ◦C, the gellant layer no longer exerts any influence on the combustion of the gel droplet.


Introduction
Gel propellants can be prepared by agitating liquid fuels with various gellants, depending on the properties required.Similar to liquid propellants, the gel propellants are subject to re-ignition, allowing thrust control when necessary.Such gel propellants exhibit an excellent stability, while allowing for easy handling and storage like solid propellants [1].The gel propellants have been intensely studied since the 1940s, commencing by research on slurry fuels.Until the 1970s, gel propellants were studied as missile and rocket fuels, principally in the USA, but their combustion characteristics were less than theoretically expected [2].However, after two successful flight tests by TRW in 1999 [3], further research recommenced in 2000.
Useful gel propellants must exhibit a shear thinning characteristic, which can be characterized rheologically [4][5][6][7].Spray and atomization studies with a preparation of simulants were previously performed at the injector exit to determine if its performance was good enough compared with conventional liquid fuels [8][9][10][11][12][13].Numerical studies have also been conducted to better understand the gel flow and droplet collisions [14,15].Additional performance must be also evaluated in terms of ignition delay, the heat of combustion, and the burning rate; these can be explored both theoretically and experimentally.Kunin et al. [16] developed a theoretical model of a gel droplet combustion with organic gellant and numerically solved the model.Mishra et al. [17] reported that the burning rate constant decreased as the gellant concentration increased.Using an UDMH-RFNA gel containing metal particles, Gupta and Varma [18] found that the heat of combustion was lower than its theoretical value.Liu et al. [19] studied the combustion and microexplosion of UDMH gel experimentally, and found that the intensity of microexplosion decreased with pressure.Bar-or and Natan [20] studied the effects of pressure and ambient oxygen mass fraction on the burning rate of a kerosene gel.Arnold and Anderson [21] explored the rheological and combustion characteristics of a JP-8/silica gel, and reported that the d 2 -law used to analyze an evaporation of liquid fuel droplets could also be applied to a gel droplet behavior.Solomon et al. [22] confirmed that a gellant layer formation during droplet combustion was caused by a difference in the boiling points and viscosities of the gel propellant constituents.Negri and Ciezki [23] showed that aggregation occurred when a gel propellant containing aluminum particles based on jet A-1 was burned.It explained low combustion efficiency than expected.Recently, a research with optical access on gel combustion chamber was also carried out, which made detailed analysis possible [24].
The combustion of a single gel droplet lacking metal particles can be divided into four stages, of which the first is heat-up, similar to the combustion of a typical liquid fuel droplet.In the second stage, a film or layer of gellant is formed, followed by swelling or a micro-explosion as the fuel bubble inside the droplet expands.Thereafter, the gellant layer thickens and bursts in the third stage, triggering fuel vapor jetting and rupture of the flame structure.At the stage four, the gellant begins to burn, either exhibiting a uniform regression of the droplet or other very complicated behavior depending on the type of gelling agent used [17,22].
Previously, most of researchers used to observe combustion behavior characteristics after an external ignition of the gel droplet.However, an autoignition characteristic of the gel droplet was rarely investigated.Therefore, in this study the autoignition characteristic of the gel droplet is to be observed and investigated.Autoignition occurs if fuel vapor is mixed with an appropriate concentration of oxidizer, and the temperature around the droplet is higher than the autoignition temperature.Regarding the autoignition in this study, the gel droplet is to be observed throughout the time interval from evaporation to combustion, which allows the autoignition behavior of the gel droplet to be better understood.

Ethanol Gel Preparation
Ethanol (CAS number 64-17-5; Sigma-Aldrich, St. Louis, MO, USA) was selected as a parent fuel because it is minimally toxic and easy to handle.Its autoignition temperature is 363 • C according to the manufacturer.Methylcellulose (CAS number: 9004-67-5; Sigma-Aldrich) served as the organic gellant since it is an eco-friendly material.The solvent was distilled water because the gelation mechanism of methylcellulose is cross link of hydrophobic units of methylcellulose.Gellant levels of 9-11 wt % were used to make gels with excellent rheological properties in preliminary tests.Ethanol gel with 10 wt % of methylcellulose was selected for further study as shown in Figure 1, since it exhibits a shear thinning behavior.Its compositions are listed in Table 1.The calorific value measured in an oxygen bomb calorimeter (1341 Plain Jacket Bomb Calorimeter and 6772 Calorimetric Thermometer, Parr Instrument Company, Moline, IL, USA) was 27.57MJ/kg which is about 93% of the calorific value of pure liquid ethanol.

Combustion Chamber
A combustion chamber was used to study an autoignition phenomenon of the ethanol gel and its schematic is shown in Figure 2. The electric furnace can be moved vertically to rapidly expose a gel droplet to high temperature environment, which was controlled within 5 °C using a proportional-integral-derivative (PID) device.

Combustion Chamber
A combustion chamber was used to study an autoignition phenomenon of the ethanol gel and its schematic is shown in Figure 2. The electric furnace can be moved vertically to rapidly expose a gel droplet to high temperature environment, which was controlled within 5 • C using a proportional-integral-derivative (PID) device.

Combustion Chamber
A combustion chamber was used to study an autoignition phenomenon of the ethanol gel and its schematic is shown in Figure 2. The electric furnace can be moved vertically to rapidly expose a gel droplet to high temperature environment, which was controlled within 5 °C using a proportional-integral-derivative (PID) device.The gel droplet was suspended on a K-type thermocouple using a 23-gauge syringe.It allowed a measurement of droplet internal temperature.In most of the droplet researches, droplets were suspended on quartz fibers just as the previous researchers who used this experimental apparatus.Meanwhile, Harada et al. [25] studied the effect of thermocouple diameter when droplet suspended both numerically and experimentally.According to his research, in case of 50 µm wire, which is same as this study, maximum temperature error was less than 10% with good agreement of experiment and numerical simulation.Also Khan et al. [26] reported that the temperature reaches to the 98% of the set value in less than 50 ms for the tests below 1.0 MPa.Such a chamber has been used by previous researches and more details are available therein [27][28][29].

High-Speed Camera
A high-speed camera (X-stream 3, Integrated Design Tools, Pasadena, CA, USA) was used to observe a transient behavior of the gel droplet.Two hundred high-resolution color images per second were acquired for each experiment, from which a variation of the droplet diameter was estimated using an in-house visual basic software.This process has been used by many researchers [27][28][29].Gel configuration is not completely spherical, therefore the droplet image boundary was converted to the effective spherical diameter of the same surface area [30].

Ignition Delay and Average Burning Rate
Once the gel droplet is exposed to a high temperature environment, it begins to evaporate while being heated up and the fuel vapor generated around the droplet starts to diffuse radially.When the vapor mixes with air and it reaches the ignition temperature, the mixture is ignited [26].The time elapsed from an exposure of the gel droplet to high temperature to the onset of ignition is termed as the ignition delay [31], which usually consists of both physical and chemical delays.The physical delay accounts for the period from droplet heating to evaporation and a formation of a combustible mixture.The chemical delay takes account of the time required for the mixture to overcome the activation energy, finally reaching an onset of ignition [32].In this study, a diffusion controlled flame would be expected so that the physical delay is to be predominant.In the following, the time from flame ignition to its extinction is termed as the flame lifetime, while the time from initial droplet exposure to high temperature to flame extinction is referred to as the droplet lifetime which includes the ignition delay and flame lifetime.
As an ethanol gel is a multi-component fuel, very active and unexpected changes are to be expected during combustion, unlike the case with single liquid fuel droplets.Thus, the concept of an average burning rate is introduced to study the droplet behavior exhibiting an active micro-explosion as for the emulsion droplet combustion [33]: where D ig is the droplet diameter at the onset of ignition, and D ext that at the time of flame extinction; t 1 is the time elapsed between ignition and extinction.

Experimental Condition
Experiments were performed under an atmospheric pressure condition at the ambient temperature of 600, 700, and 800 • C. In previous studies, it was not known how the surrounding temperature affected the ignition and combustion of the gel droplet because of the use of external ignition source.Therefore, we will focus on the change of ignition delay and average burning rate to study the effect of temperature quantitatively.In addition, pure ethanol droplet was compared with gel droplet under the same conditions.This will clearly show the autoignition characteristic of gel droplet.

Ignition and Combustion Behavior of Ethanol Gel
The gel droplet diameter was 1.17 ± 0.23 mm and the standard deviation 0.11 mm.The experiment was repeated seven times for each case.Figures 3-5 show the autoignition and combustion process of the ethanol gel droplet with 10 wt % of methylcellulose.As shown in the figures, the gel droplet was ignited at all the temperatures of 600, 700, and 800 • C, while leaving no residues.Before ignition, the droplet volumes generally decreased, but sometimes, a sudden expansion (swelling) was observed as in Figures 3b and 4b which is caused by gas expansion trapped in the gellant layer [22].At 600 • C, when the gel droplet was exposed to high temperature, the ethanol and water contents are evaporated and the gellant layer begins to form.After the onset of ignition as in Figure 3d, the droplet size rapidly decreased while burning without leaving any residue.A similar behavior was observed for the gel droplet at 700 • C, but both ignition as shown in Figure 4e and combustion proceeded faster than at 600 • C.

Ignition and Combustion Behavior of Ethanol Gel
The gel droplet diameter was 1.17 ± 0.23 mm and the standard deviation 0.11 mm.The experiment was repeated seven times for each case.Figures 3-5 show the autoignition and combustion process of the ethanol gel droplet with 10 wt % of methylcellulose.As shown in the figures, the gel droplet was ignited at all the temperatures of 600, 700, and 800 °C, while leaving no residues.Before ignition, the droplet volumes generally decreased, but sometimes, a sudden expansion (swelling) was observed as in Figures 3b and 4b which is caused by gas expansion trapped in the gellant layer [22].At 600 °C, when the gel droplet was exposed to high temperature, the ethanol and water contents are evaporated and the gellant layer begins to form.After the onset of ignition as in Figure 3d, the droplet size rapidly decreased while burning without leaving any residue.A similar behavior was observed for the gel droplet at 700 °C, but both ignition as shown in Figure 4e and combustion proceeded faster than at 600 °C.At 800 °C, the ignition occurred much faster as in Figure 5c which was then followed by a sharp decrease in size and complete gellant combustion.At this time, the droplet surface became reddish as in Figure 5g while no flame was apparent, but combustion was nonetheless completed, which is attributable to the combustion of the gellant residue.The similar combustion behavior of remaining

Ignition and Combustion Behavior of Ethanol Gel
The gel droplet diameter was 1.17 ± 0.23 mm and the standard deviation 0.11 mm.The experiment was repeated seven times for each case.Figures 3-5 show the autoignition and combustion process of the ethanol gel droplet with 10 wt % of methylcellulose.As shown in the figures, the gel droplet was ignited at all the temperatures of 600, 700, and 800 °C, while leaving no residues.Before ignition, the droplet volumes generally decreased, but sometimes, a sudden expansion (swelling) was observed as in Figures 3b and 4b which is caused by gas expansion trapped in the gellant layer [22].At 600 °C, when the gel droplet was exposed to high temperature, the ethanol and water contents are evaporated and the gellant layer begins to form.After the onset of ignition as in Figure 3d, the droplet size rapidly decreased while burning without leaving any residue.A similar behavior was observed for the gel droplet at 700 °C, but both ignition as shown in Figure 4e and combustion proceeded faster than at 600 °C.At 800 °C, the ignition occurred much faster as in Figure 5c which was then followed by a sharp decrease in size and complete gellant combustion.At this time, the droplet surface became reddish as in Figure 5g while no flame was apparent, but combustion was nonetheless completed, which is attributable to the combustion of the gellant residue.The similar combustion behavior of remaining

Ignition and Combustion Behavior of Ethanol Gel
The gel droplet diameter was 1.17 ± 0.23 mm and the standard deviation 0.11 mm.The experiment was repeated seven times for each case.Figures 3-5 show the autoignition and combustion process of the ethanol gel droplet with 10 wt % of methylcellulose.As shown in the figures, the gel droplet was ignited at all the temperatures of 600, 700, and 800 °C, while leaving no residues.Before ignition, the droplet volumes generally decreased, but sometimes, a sudden expansion (swelling) was observed as in Figures 3b and 4b which is caused by gas expansion trapped in the gellant layer [22].At 600 °C, when the gel droplet was exposed to high temperature, the ethanol and water contents are evaporated and the gellant layer begins to form.After the onset of ignition as in Figure 3d, the droplet size rapidly decreased while burning without leaving any residue.A similar behavior was observed for the gel droplet at 700 °C, but both ignition as shown in Figure 4e and combustion proceeded faster than at 600 °C.At 800 °C, the ignition occurred much faster as in Figure 5c which was then followed by a sharp decrease in size and complete gellant combustion.At this time, the droplet surface became reddish as in Figure 5g while no flame was apparent, but combustion was nonetheless completed, which is attributable to the combustion of the gellant residue.The similar combustion behavior of remaining At 800 • C, the ignition occurred much faster as in Figure 5c which was then followed by a sharp decrease in size and complete gellant combustion.At this time, the droplet surface became reddish as in Figure 5g while no flame was apparent, but combustion was nonetheless completed, which is attributable to the combustion of the gellant residue.The similar combustion behavior of remaining gellant is also observed for the case with 600 and 700 • C as in Figures 3g and 4g.Generally vapor jetting can be observed at all temperatures and is particularly noticeable just after swelling.When swelling occurs due to the expansion of the gas inside of droplet, the thickness of gellant layer becomes thinner as the volume becomes larger.If tiny holes are created on the gellant layer, the vapor escapes to the outside.Figure 6 shows an instantaneous flame through the jetted vapor, which was observed once in a while.In the left-hand side image, the arrow points to a rupture in the gellant layer.Instantly, hot ethanol vapor jetted out of the gellant layer through dashed arrow and ignited quickly in contact with oxygen, forming an immediate flame as shown in the right-hand side image.
Energies 2018, 11, x FOR PEER REVIEW 6 of 11 gellant is also observed for the case with 600 and 700 °C as in Figures 3g and 4g.Generally vapor jetting can be observed at all temperatures and is particularly noticeable just after swelling.When swelling occurs due to the expansion of the gas inside of droplet, the thickness of gellant layer becomes thinner as the volume becomes larger.If tiny holes are created on the gellant layer, the vapor escapes to the outside.Figure 6 shows an instantaneous flame through the jetted vapor, which was observed once in a while.In the left-hand side image, the arrow points to a rupture in the gellant layer.Instantly, hot ethanol vapor jetted out of the gellant layer through dashed arrow and ignited quickly in contact with oxygen, forming an immediate flame as shown in the right-hand side image.According to the four-stage combustion of the gel droplet from previous study, which was introduced in chapter 1, there was flame from the beginning of heating up process (stage I) since it used an external ignition source.However, in this experiment, those occurred during heating up and evaporation process without flame.These differences make direct comparison difficult, but still combustion process of ethanol gel droplet can also be divided to four stages.Heating up process for stage I is (a)-(b) in the Figures 3-5, where ethanol and water begin to evaporate.Stage II can be (b)-(c) in the Figures 3-5, which includes formation of gellant layer followed by swelling and decrease of size.Gellant layer thickens and bursts in stage III, it leads to vapor jetting and ignition of the droplet that are shown at (d)-(f) in the Figures 3-5.Finally, at (g)-(h) in the Figures 3-5, the rest gellant burns exhibiting a uniform regression, which is stage IV.

Droplet Diameter Variation for Various Ambient Temperatures
Figure 7 shows the pure ethanol droplet size change at each temperature.At 600 °C, the pure ethanol droplet size deceased very steadily, but it was not ignited, presumably because all the heat feedback to the pure ethanol droplet might be used for its evaporation.According to the four-stage combustion of the gel droplet from previous study, which was introduced in chapter 1, there was flame from the beginning of heating up process (stage I) since it used an external ignition source.However, in this experiment, those occurred during heating up and evaporation process without flame.These differences make direct comparison difficult, but still combustion process of ethanol gel droplet can also be divided to four stages.Heating up process for stage I is (a)-(b) in the Figures 3-5, where ethanol and water begin to evaporate.Stage II can be (b)-(c) in the Figures 3-5, which includes formation of gellant layer followed by swelling and decrease of size.Gellant layer thickens and bursts in stage III, it leads to vapor jetting and ignition of the droplet that are shown at (d)-(f) in the Figures 3-5.Finally, at (g)-(h) in the Figures 3-5, the rest gellant burns exhibiting a uniform regression, which is stage IV.

Droplet Diameter Variation for Various Ambient Temperatures
Figure 7 shows the pure ethanol droplet size change at each temperature.At 600 • C, the pure ethanol droplet size deceased very steadily, but it was not ignited, presumably because all the heat feedback to the pure ethanol droplet might be used for its evaporation.gellant is also observed for the case with 600 and 700 °C as in Figures 3g and 4g.Generally vapor jetting can be observed at all temperatures and is particularly noticeable just after swelling.When swelling occurs due to the expansion of the gas inside of droplet, the thickness of gellant layer becomes thinner as the volume becomes larger.If tiny holes are created on the gellant layer, the vapor escapes to the outside.Figure 6 shows an instantaneous flame through the jetted vapor, which was observed once in a while.In the left-hand side image, the arrow points to a rupture in the gellant layer.Instantly, hot ethanol vapor jetted out of the gellant layer through dashed arrow and ignited quickly in contact with oxygen, forming an immediate flame as shown in the right-hand side image.According to the four-stage combustion of the gel droplet from previous study, which was introduced in chapter 1, there was flame from the beginning of heating up process (stage I) since it used an external ignition source.However, in this experiment, those occurred during heating up and evaporation process without flame.These differences make direct comparison difficult, but still combustion process of ethanol gel droplet can also be divided to four stages.Heating up process for stage I is (a)-(b) in the Figures 3-5, where ethanol and water begin to evaporate.Stage II can be (b)-(c) in the Figures 3-5, which includes formation of gellant layer followed by swelling and decrease of size.Gellant layer thickens and bursts in stage III, it leads to vapor jetting and ignition of the droplet that are shown at (d)-(f) in the Figures 3-5.Finally, at (g)-(h) in the Figures 3-5, the rest gellant burns exhibiting a uniform regression, which is stage IV.

Droplet Diameter Variation for Various Ambient Temperatures
Figure 7 shows the pure ethanol droplet size change at each temperature.At 600 °C, the pure ethanol droplet size deceased very steadily, but it was not ignited, presumably because all the heat feedback to the pure ethanol droplet might be used for its evaporation.For the case with the ethanol gel droplet, however, the evaporation might be hindered by the surface gellant layer, while the ethanol vapor inside it was heated.On the other hand, at 700 • C, the diameter reduced almost linearly during the evaporation process, and the slope changed after ignition.At 800 • C, there was slight perturbation during the initial heating up period, but after the ignition, the diameter decreased almost uniformly.Droplet lifetime shortened as the ambient temperature increased.
Figure 8 shows the transient ethanol gel droplet size and internal temperature variations for ambient temperatures of 600, 700, and 800 • C. The droplet size decrease due to evaporation and then its rapid increase due to swelling were repeatedly observed.This droplet behavior, however, was not observed for 800 • C. Just at an onset of ignition, a sudden major swelling occurrence was apparent for all the temperatures.At this time, it is apparent that the fuel vapor released through the ruptured gellant layer is ignited.
For the case with the ethanol gel droplet, however, the evaporation might be hindered by the surface gellant layer, while the ethanol vapor inside it was heated.On the other hand, at 700 °C, the diameter reduced almost linearly during the evaporation process, and the slope changed after ignition.At 800 °C, there was slight perturbation during the initial heating up period, but after the ignition, the diameter decreased almost uniformly.Droplet lifetime shortened as the ambient temperature increased.
Figure 8 shows the transient ethanol gel droplet size and internal temperature variations for ambient temperatures of 600, 700, and 800 °C.The droplet size decrease due to evaporation and then its rapid increase due to swelling were repeatedly observed.This droplet behavior, however, was not observed for 800 °C.Just at an onset of ignition, a sudden major swelling occurrence was apparent for all the temperatures.At this time, it is apparent that the fuel vapor released through the ruptured gellant layer is ignited.For the cases with 600 and 700 °C, when there occurs an onset of ignition as marked in Figure 8, the flame shape is observed to be spherical as shown in Figures 4d and 5e, respectively.The ignition is then followed by a rapid increase in the gel droplet core temperature as in Figure 8.Since the internal gel droplet temperature exceeded the ethanol autoignition temperature, the fuel vapor escaping through the gellant layer would be easy to ignite as soon as it formed a combustible mixture with oxygen.On the other hand, this rapid increase behavior in the gel droplet temperature was not observed for the case with 800 °C as shown in Figure 8.In this case, no active combustion was evident because the gel droplet temperature at the onset of ignition was lower than the For the cases with 600 and 700 • C, when there an onset of ignition as marked in Figure 8, the flame shape is observed to be spherical as shown in Figures 4d and 5e, respectively.The ignition is then followed by a rapid increase in the gel droplet core temperature as in Figure 8.Since the internal gel droplet temperature exceeded the ethanol autoignition temperature, the fuel vapor escaping through the gellant layer would be easy to ignite as soon as it formed a combustible mixture with oxygen.On the other hand, this rapid increase behavior in the gel droplet temperature was not observed for the case with 800 • C as shown in Figure 8.In this case, no active combustion was evident because the gel droplet temperature at the onset of ignition was lower than the autoignition temperature.Consequently, a spherical flame was developed and observed in Figure 6e, which was much later than the onset of ignition as in Figure 6c, i.e., only after the internal droplet temperature had risen sufficiently.
After ignition, the gel droplet diameter decreased rapidly without further swelling, which is different from what is seen when an external ignition source is employed.Previous studies [17,21,22,34] described the droplet swelling even during combustion.However, the droplet swelling during combustion after the ignition was not observed in this study, presumably because the combustion commenced only after a sufficient amount of ethanol evaporated.Particularly, during the major swelling that is evident just at the onset of ignition, the fuel vapor inside the droplet might be fully released, which made no further swelling.

IgnitionDdelay and Average Burning Rate
Figure 9 shows the ignition delay and flame lifetime of pure liquid ethanol and the ethanol gel with 10 wt % of methylcellulose.Their corresponding average burning rate is listed in Table 2.
Energies 2018, 11, x FOR PEER REVIEW 8 of 11 autoignition temperature.Consequently, a spherical flame was developed and observed in Figure 6e, which was much later than the onset of ignition as in Figure 6c, i.e., only after the internal droplet temperature had risen sufficiently.After ignition, the gel droplet diameter decreased rapidly without further swelling, which is different from what is seen when an external ignition source is employed.Previous studies [17,21,22,34] described the droplet swelling even during combustion.However, the droplet swelling during combustion after the ignition was not observed in this study, presumably because the combustion commenced only after a sufficient amount of ethanol evaporated.Particularly, during the major swelling that is evident just at the onset of ignition, the fuel vapor inside the droplet might be fully released, which made no further swelling.

IgnitionDdelay and Average Burning Rate
Figure 9 shows the ignition delay and flame lifetime of pure liquid ethanol and the ethanol gel with 10 wt % of methylcellulose.Their corresponding average burning rate is listed in Table 2.The ignition delay of the ethanol gel was found to be longer than that of pure ethanol at 700 °C as observed in Figure 9, because the gellant layer might inhibit its efficient evaporation.At 800 °C, the ignition delay of the pure ethanol and the ethanol gel was very similar and it was much shorter than that at 600 and 700 °C.
The average burning rate increased as the temperature increased, as seen at 700 and 800 °C for pure ethanol and at 600 and 700 °C for the ethanol gel.Also the burning rate of pure ethanol were lower than that of gel.At 700 °C, the ignition delay was shorter than the gel case, thus larger droplet was burned and lower value was evaluated.At 800 °C, the ignition delay was similar with the gel case.However, unlike ethanol, which maintained almost constant internal temperature, the internal  The ignition delay of the ethanol gel was found to be longer than that of pure ethanol at 700 • C as observed in Figure 9, because the gellant layer might inhibit its efficient evaporation.At 800 • C, the ignition delay of the pure ethanol and the ethanol gel was very similar and it was much shorter than that at 600 and 700 • C.
The average burning rate increased as the temperature increased, as seen at 700 and 800 • C for pure ethanol and at 600 and 700 • C for the ethanol gel.Also the burning rate of pure ethanol were lower than that of gel.At 700 • C, the ignition delay was shorter than the gel case, thus larger droplet was burned and lower value was evaluated.At 800 • C, the ignition delay was similar with the gel case.However, unlike ethanol, which maintained almost constant internal temperature, the internal

Figure 3 .
Figure 3. Ignition and combustion behavior of ethanol gel at 600 °C.

Figure 4 .
Figure 4. Ignition and combustion behavior of ethanol gel at 700 °C.

Figure 5 .
Figure 5. Ignition and combustion behavior of ethanol gel at 800 °C.

Figure 3 .
Figure 3. Ignition and combustion behavior of ethanol gel at 600 • C.

Figure 3 .
Figure 3. Ignition and combustion behavior of ethanol gel at 600 °C.

Figure 4 .
Figure 4. Ignition and combustion behavior of ethanol gel at 700 °C.

Figure 5 .
Figure 5. Ignition and combustion behavior of ethanol gel at 800 °C.

Figure 4 .
Figure 4. Ignition and combustion behavior of ethanol gel at 700 • C.

Figure 3 .
Figure 3. Ignition and combustion behavior of ethanol gel at 600 °C.

Figure 4 .
Figure 4. Ignition and combustion behavior of ethanol gel at 700 °C.

Figure 5 .
Figure 5. Ignition and combustion behavior of ethanol gel at 800 °C.

Figure 5 .
Figure 5. Ignition and combustion behavior of ethanol gel at 800 • C.

Figure 6 .
Figure 6.Flame on vapor jetting of ethanol gel droplet.

Figure 7 .
Figure 7. Pure ethanol droplet size variation for various ambient temperatures.

Figure 6 .
Figure 6.Flame on vapor jetting of ethanol gel droplet.

Figure 6 .
Figure 6.Flame on vapor jetting of ethanol gel droplet.

Figure 7 .
Figure 7. Pure ethanol droplet size variation for various ambient temperatures.

Figure 7 .
Figure 7. Pure ethanol droplet size variation for various ambient temperatures.

Figure 8 .
Figure 8. Ethanol gel droplet size and temperature variations for various ambient temperatures.

Figure 8 .
Figure 8. Ethanol gel droplet size and temperature variations for various ambient temperatures.

Figure 9 .
Figure 9. Ignition delay and flame lifetime of ethanol gel.

Figure 9 .
Figure 9. Ignition delay and flame lifetime of ethanol gel.

Table 1 .
Composition of ethanol gel with 10 wt % of methylcellulose.

Table 1 .
Composition of ethanol gel with 10 wt % of methylcellulose.

Table 1 .
Composition of ethanol gel with 10 wt % of methylcellulose.

Table 2 .
Average burning rate of ethanol gel for various conditions.

Table 2 .
Average burning rate of ethanol gel for various conditions.