Solid Fuel Production from Semi-Natural Grassland Biomass—Results from a Commercial-Scale IFBB Plant

: Biomass-based energy accounts for a notable share of renewable heat and electricity generation in Germany. Due to limited alternative uses, biomass obtained from management of semi-natural grasslands is a potential feedstock. Technical and environmental limitations exist in using this biomass for combustion, due to the presence of harmful elements. Converting biomass using integrated generation of solid fuel and biogas from biomass system (IFBB) produces a solid fuel with lower concentrations of harmful elements and a press liquid usable for biogas generation. In this study, solid fuel generation with a commercial scale IFBB unit was investigated. The concentration of harmful elements such as N, S, Cl, and K in the solid fuel was signiﬁcantly reduced compared to the original biomass silage. Emissions during combustion of the solid fuel briquettes were below German legal thresholds. Elemental concentration of solid fuel obtained from commercial scale process had a signiﬁcant improvement in removal rate of harmful elements than the prototype. Hence, the limitations of using semi-natural grassland biomass as an energy source were overcome. The commercial scale IFBB plant could be used in practice to handle large volumes of green residual biomass by converting it into a solid fuel with favorable fuel properties.


Introduction
The energy transition "Energiewende" in Germany aims to mitigate climate change by replacing fossil fuels and to realize a stable energy supply that is both economically feasible and environmentally friendly [1]. Bioenergy involves mainly biogenic solid fuel (e.g., firewood), biogenic liquid fuel (e.g., ethanol) and biogas, which account for 27% and 86% of renewable based electricity and heat generation, respectively [2]. While politics focused on only electricity in the recent years, generation of renewable heat is now increasingly supported. Mitigation of climate change is less effective when land-intensive bioenergy feedstocks are used, leading to detrimental climate effects and negative impacts on the ecosystem and biodiversity [3]. Further, the increasing demand for land for non-food purposes in the present scenario where food and feed demand are expected to increase, could be a threat to food security [4]. Enlarging the biomass base with residual biomass and strictly cascading the use of biomass can help in reducing the competition with land for food [5]. Therefore, potential biomass sources for bioenergy in the future should minimize conflict with food and feed production and have low negative impacts on the environment, i.e., water bodies, atmosphere, and biodiversity [6].
In the early half of the 20th century, low-intensity land use had led to species rich and biodiverse grassland areas in Europe, but in the latter half of the century, biodiverse but unproductive habitats and (iii) the ash melting behavior of the silage and the fuels produced.
To gain insight into upscaling effects related to the IFBB procedure, fuel data from the commercial scale were compared with those from the prototype scale.

Commercial Scale Plant
The commercial-scale IFBB unit used for this study is capable of handling 12,000 tons of fresh biomass per year which consists, among others, mainly of green cut, wood, brushwood, grass, and tree leaves. This unit is part of the municipal sewage plant of the Baden-Baden city Environment Technique in south-west Germany, the plant has a capacity of 200,000 population equivalents. The presence of green areas and forests, in and around the city leads to the high availability of biomass feedstock. In addition to this, the biomass from various nature conservation areas is also handled at this facility. In the past, biomass that arrived at the facility was composted but this was no longer feasible as the costs of producing a high-quality compost were rising, whereas the demand for compost did not. Hence, the IFBB process was implemented on a large scale to convert the biomass into a solid fuel that is either combusted on-site or compacted into briquettes for storage and transport before combustion. The press fluid obtained is fed into the hydrolysis stage of a biogas plant to produce biogas for heat and electricity generation. The solid fuel and briquettes produced had a density of 600 kg·m −3 and 1000 kg·m −3 , respectively. In Baden-Baden, the loose solid fuel is combusted in a biomass boiler (ALA-TALKKARI-Veto 500) with a capacity of 2 × 420 kW. The heat produced is used for internal needs of the plant, such as heating of digesters and buildings and drying of press cake and wood chips.
Test material from the different regions was delivered to the Baden-Baden facility in silage bales weighing approximately 500 kg. The operational flow of the process to produce solid fuel from biomass at the Baden-Baden unit is depicted in (Figure 1). Upon reception, the silage bales were inserted into a bale dissolving unit (Arjes-VZ 750D, Germany) to loosen the compacted silage. The silage was then passed through a 90-kW cross flow shredder (MEBA-UNI-CUT ® Bio-QZ 1200, Germany) that crushed the silage using rotating metal chains to obtain a homogeneous short fiber length, which was required to process the silage in forthcoming steps. Then, the crushed silage was compacted by a bale press and enwrapped with foil. With the help of a band conveyor, the silage was transported into a 25 m 3 mashing tank for hydrothermal conditioning. The hydrothermal conditioning process involved the mixing of silage with cleaned water from the sewage plant for 40 min. Even though higher mashing temperature aids in better removal of unwanted elements from the press cake [26], the mashing was done using tap water at 10 • C. Heating was not possible due to the high energy demand to warm the large quantity of water used for the commercial scale process. The quantity of water used was proportional to the dry matter (DM) content of the silage, to achieve a fluidic mash with a DM content of approximately 3-5% that could be easily pumped. The mash was then passed through a 60-kW screw press (FAN SEPARATOR, Germany), the resulting press fluid was directed to a 2000 m 3 anaerobic digester and the solid fuel obtained was transferred into a band dryer (NEW eco-tec). The dried solid fuel which contained around 90% DM was compacted into briquettes using a 50-kW briquette press (Mütek-MAP 750, Germany).

Grassland Biomass
Botanical determination was conducted on three random study areas of 5 m × 5 m which were established at each of the 11 grassland sites. Vegetation was mostly dominated by grasses and sedges but with distinct differences in the botanical composition (Table 1, for botanical details see Table A1). The test material included grassland silages from Belgium, roadside maintenance cuttings from France, and wetland vegetation from Wales. Further silages originated from typical floodplain areas across Central Europe (Table 1). Green cut and grassland biomass that was deposited at the Baden-Baden municipal plant was also included for the comparison between prototype and commercialscale plant. As this sample was a mix of various residual biomass from the Baden-Baden region, data on the composition of vegetation was not available.

Grassland Biomass
Botanical determination was conducted on three random study areas of 5 m × 5 m which were established at each of the 11 grassland sites. Vegetation was mostly dominated by grasses and sedges but with distinct differences in the botanical composition (Table 1, for botanical details see Table A1). The test material included grassland silages from Belgium, roadside maintenance cuttings from France, and wetland vegetation from Wales. Further silages originated from typical floodplain areas across Central Europe (Table 1). Green cut and grassland biomass that was deposited at the Baden-Baden municipal plant was also included for the comparison between prototype and commercial-scale plant. As this sample was a mix of various residual biomass from the Baden-Baden region, data on the composition of vegetation was not available.

Chemical Analysis and Heating Value
Silage samples for the chemical analysis were taken after opening and chopping the silage bales, the press cake samples were taken after mashing, pressing, and drying. Eight silage and 8 press cake samples from the DANUBENERGY project, 3 silage and 3 press cake samples from the COMBINE project, and 1 silage and 1 press cake sample from Baden-Baden were taken to be tested, with 3 replicates of each sample amounting to a total of 36 silage and 36 press cake samples which were used for this study. The analysis of mineral content in the silage and solid fuel was carried out using X-ray fluorescence spectroscopy by an accredited external laboratory. Carbon (C), Hydrogen (H), and N content in samples were measured using 150 mg of dried material in an elemental analyzer (Vario MAX CHN Elementar Analysensysteme GmbH, Hanau, Germany). Using data from the above analysis, the higher heating value (HHV) was calculated using the following equation [34]. (1) The lower heating value (LHV) was calculated from HHV by deducting the latent heat of vaporization, where 8.937 is the mass share of hydrogen in a water molecule and 2.2 is the enthalpy of water vaporization, C, H, and N are carbon, hydrogen, and nitrogen in the press cake expressed in %DM.
Corrosion index (2S/Cl) was used to identify the risk of corrosion and was calculated according to reference [22]

Combustion and Ash Melting Test
Combustion tests were carried out with the solid fuels AC, AE, AM, CD, DC, and PA2 in the form of compacted briquettes. The tests were conducted on a test bench with an ÖKOTHERM-compact plant C1L (ÖKOTHERM, Germany) with a nominal output of 120 kW in accordance with the DIN EN304 [35] criteria. The boiler output was adjusted continuously between 30-100% of the nominal load. For each fuel type, the tests were carried out in three phases; heat-up phase, partial load (50% nominal output), and full load (100% nominal output). The heating system is stoker-fired and has a cooled combustion cavity; automated lambda control was also included. The experimental procedure was carried out in accordance with DIN EN 303-5 [36]. The gas and particulate matter (PM) emissions were tested using a standardized emission test section installed in the exhaust line. The levels of O 2 , CO 2 , CO, NO x , and SO 2 in the exhaust were detected using an ecom-J2KNpro (Ecom, Germany) compact analyzer. The amount of fuel used was determined by weighing hourly over the test period, the power and efficiency were calculated in accordance with DIN EN 0304 + A.7 A.8 [35]. The removal of ash was carried out by an ash pusher into a collection tray.
For the ash melting test, 30 g of biomass was ground with a cutting mill and incinerated in a muffle furnace at 550 • C. The material was annealed for 1 h at 700 • C for full incineration; the ashes produced were compacted into a cylindrical form of 3 mm diameter and 3 mm height. The ash melting behavior was tested using a hot stage microscope (Hesse Instruments, Germany) connected to a CCD camera. Automatic contour recognition and evaluation of the silhouettes were used to identify characteristic temperatures at softening, spherical, hemispherical, and flowing point of the ashes according to DIN 51730 [37], ISO 540 [38], CEN/TS 15404 [39], and CEN/TS 15370-1 [40]. The temperature inside the microscope was increased at a rate of 10 K·min −1 and images were captured every minute. When the software had difficulties in identifying the form, manual identification was used. In some cases, the form could not be determined neither automatically nor manually; this difficulty mainly occurred for the spherical and hemispherical stage.

Prototype Plant
For the comparison of commercial ( Figure 1) and prototype ( Figure 2) plants, data on elemental reduction originates from reference [28] and data on ash melting behavior was provided by reference [30]. Data for the above studies involved grassland biomass samples from a total of 18 sites in Estonia, Germany, and the United Kingdom. The conversion of biomass samples to solid fuel was done in a prototype scale IFBB unit which could handle 300 kg per day (for details see [28]). Unlike the commercial scale unit, the silage to water ratio during the mashing stage was held constant at 1:8 and the mashing time was 30 min with a water temperature of 25 • C. The process parameters are summarized in (Table 2), the parameters given below show the variation in operating conditions for the prototype and commercial scale. melting behavior was tested using a hot stage microscope (Hesse Instruments, Germany) connected to a CCD camera. Automatic contour recognition and evaluation of the silhouettes were used to identify characteristic temperatures at softening, spherical, hemispherical, and flowing point of the ashes according to DIN 51730 [37], ISO 540 [38], CEN/TS 15404 [39], and CEN/TS 15370-1 [40]. The temperature inside the microscope was increased at a rate of 10 K·min −1 and images were captured every minute. When the software had difficulties in identifying the form, manual identification was used. In some cases, the form could not be determined neither automatically nor manually; this difficulty mainly occurred for the spherical and hemispherical stage.

Prototype Plant
For the comparison of commercial ( Figure 1) and prototype ( Figure 2) plants, data on elemental reduction originates from reference [28] and data on ash melting behavior was provided by reference [30]. Data for the above studies involved grassland biomass samples from a total of 18 sites in Estonia, Germany, and the United Kingdom. The conversion of biomass samples to solid fuel was done in a prototype scale IFBB unit which could handle 300 kg per day (for details see [28]). Unlike the commercial scale unit, the silage to water ratio during the mashing stage was held constant at 1:8 and the mashing time was 30 min with a water temperature of 25 °C. The process parameters are summarized in (Table 2), the parameters given below show the variation in operating conditions for the prototype and commercial scale.

Statistical Analysis
Statistical analysis was carried out using R software package [41]. The datasets were checked for normal distribution using the Shapiro-Wilk normality test and were verified visually. Since most of the datasets were not normally distributed, differences between the silage and solid fuel in terms of elemental concentration and ash melting temperatures were tested using Wilcoxon rank sum test,

Statistical Analysis
Statistical analysis was carried out using R software package [41]. The datasets were checked for normal distribution using the Shapiro-Wilk normality test and were verified visually. Since most of the datasets were not normally distributed, differences between the silage and solid fuel in terms of elemental concentration and ash melting temperatures were tested using Wilcoxon rank sum test, which was also used for comparisons between prototype and commercial scale units. Effects of silage and press cake chemistry on the ash softening and flowing temperature were tested using multiple linear regression modelling with interactions, considering the principles of hierarchy and marginality in the development of models [42].

Elemental Concentrations
A significant reduction in the elemental concentration caused by dewatering of silage was observed for almost all elements, except for Na ( Table 3). The rate of reduction varied from 24.73% for Ca to 89.42% for Cl. The mean reduction of Cl was in the range of removal rate of Cl from biomass after washing and mechanical separation confirmed by similar studies [43]. K and S was Energies 2018, 11, 3011 7 of 17 reduced by 88% and 62%, respectively, in this study, which were above the reduction rates of 84% and 55% observed by reference [43]. According to reference [44], there would be a corrosion risk by Cl only if the concentration is above 0.1 %DM. Most of the solid fuel samples had a Cl concentration below this threshold. During combustion, S present in the biomass fuel forms alkali sulphates and gaseous SO x . Due to cooling of flue gas in the boiler, these sulphates condense at the heat exchanger. The concentration of S in the solid fuel was lower than 0.09% DM, which was slightly below the guiding value for unproblematic combustion of 0.1% DM [20]. A perception of the actual high temperature corrosion risk can be obtained by using the molar 2S/Cl ratio [22].
A ratio above 4 would indicate a minor risk and above 8 would indicate negligible risk. The 2S/Cl ratio for the solid fuel samples had an average of 3.27 ± 1.18 compared to silage values of 0.92 ± 0.40. So, the corrosion risk was comparatively lower for the press cake, but the data still indicate a minor corrosion risk. A much higher 2S/Cl ratio of 11.9 was reported for mechanically leached solid fuel from grass by reference [43], which can be explained by the lower removal rate of Cl and the higher removal rate of S in the Baden-Baden plant.
Considering the factors influencing the removal rate, previous studies showed that the removal of Cl from silage was better at lower hydrothermal conditioning temperatures [26,27]. This contrasted with the influence of temperature on the removal of other soluble elements. The improved removal of Cl at lower temperatures may be explained by the dissolution of a majority of Cl in the form of Cl − at lower temperatures and by the competition among other ions for entry into water [45]. Moreover, studies have suggested that hydrothermal conditioning temperature has a negligible effect on removal rates of soluble elements from grass silage [46] and that the effect of temperature varies with the type of biomass [45]. The silage samples had DM contents between 26.55% and 83.56%, higher DM content resulted in more water being used during the mashing process. Dry matter content and the initial concentration of elements in silage could have an influence on the reduction rate of the respective elements, this influence was reported for Cl by reference [47].
In contrast to other elements, the concentration of Na during dewatering of silage increased in some of the samples. A similar increase in Na during treatment of biomass by washing was reported by reference [48]. Externally introduced Na from the water used for hydrothermal conditioning may be a reason for this. The mean ash content in the solid fuel was 3.97 ± 0.43% DM with a reduction of 51% from the silage. Despite the ash content being relatively lower than in other herbaceous fuels, the reduction rate was in the range reported by reference [43]. Table 3. Ultimate analysis, heating values, elemental concentration and corrosion index for silage (SI) and solid fuel (SF), along with the reduction rate (RR) from silage to solid fuel for test materials processed in the commercial-scale pilot plant (see Table 1). The values in parentheses denote an increase in concentration from silage to press cake.

Ash Melting
As the elements affecting ash melting temperatures in biomass fuels are water-soluble [49], hydrothermal conditioning and mechanical separation were expected to increase the ash melting temperature from silage to solid fuel. Ash softening temperature (AST) in the solid fuel varied from 1050 • C to 1370 • C (Table 4) and the mean values were in the range of lignite and higher than for most of the herbaceous biomass fuels [49]. It was found that AST was mainly influenced by K and Ca, the former had a negative influence [30], which was also observed (R 2 = 0.23) in this study. Ca had a positive influence (R 2 = 0.33) on AST for silage, whereas in the case of solid fuel the influence was not Energies 2018, 11, 3011 9 of 17 significant. The increase in AST from silage to solid fuel was not significant even though there was a mean increase of 63 • C. This is in line with observations by reference [50] who found an increase of 12 • C, which was also not a significant increase. A similar trend was observed for ash flowing temperature (AFT). A correlation between the AST and AFT was observed for solid fuel (R 2 = 0.40), which, according to reference [49], implies that the major processes responsible for the ash melting behavior are similar. The silage ash showed a much weaker correlation (R 2 = 0.11) between AST and AFT.

Combustion and Emission
Mean lower heating value increased by 0.43 MJ kg −1 (2.5%) due to dewatering of silage, which is less than the increase found by reference [43] (10%) and [51] (5%). Ash content in the fuel has a negative correlation to the heating value [52] and the strength of this relation depends on the type of biomass used, varying from R 2 = 0.45 in rice straw to R 2 = 0.88 in wheat straw [53]. A negative relation between heating value and ash content was also found in the present study, but it was not strong (R 2 = 0.53). In the combustion tests, all briquetted fuels ignited easily with the hot air automatic ignition and a full flame in the combustion chamber could be observed within 15 min. Due to destabilization of pressed fibers in the briquettes during transportation, some flying sparks could be observed. However, the sparks had no influence on the dust content in the flue gas, as they burned in the upper part of the boiler. Flying sparks were relatively lower in the partial load operation than in the full load, because of the lower air velocity from the blower.
Due to the presence of higher N content in grassland biomass fuels (0.4 to 3.6% DM) [21], compared to solid fuels from other biomass sources, such as wood chips (0.1 to 0.9% DM) or bark (0.1 to 0.5% DM) [21], the NO x emissions tend to be higher [54]. A positive linear relationship between the fuel N content and the NO x emission was observed (R 2 = 0.89) (Figure 3), implying that the reduction in N content in the solid fuel with the IFBB process (42 ± 10%) reduced the potential for NO x emissions. In all cases, NO x emissions at full load were below the threshold of 500 mg m −3 flue gas [55].
The higher values of emissions during partial load combustion can be attributed to the incomplete burn-off in the combustion zone. The quality of combustion could be indicated by the amount of CO emitted, with a lower emission indicating a higher conversion of C into CO 2 , resulting in complete combustion [21]. CO emissions at full load were highest at λ between 1.5 and 1.6 and decreasing gradually with increasing values of λ, similar to the findings of reference [56] for Miscanthus. CD was an exception, as it had highest CO emission at λ between 2.5 and 3. This information is particularly relevant for combustion chambers without automated λ control systems. Although SO 2 emission was influenced by fuel S content, fuel S is not completely converted into SO 2 . A fraction of S remains in the ash and some is emitted as salts at lower temperatures [21]. Lower SO 2 emission was observed with partial load due to a lower operating temperature. Even though the IFBB process reduced the ash content in the press cake, PM was higher in some cases (Table 5). PM in the flue gas is a result of incomplete combustion and, hence, is in most cases higher with partial load than with full load combustion. The use of electrostatic precipitators [43] and dust filters, which is common nowadays, can further reduce PM [57]. Hence, the IFBB solid fuel can be considered an appropriate fuel for industrial application. Table 5. Mean values of CO, NO x , SO 2 , PM, and excess air fuel ratio (λ) emissions during combustion of solid fuel briquettes at partial load (60 kW) and full load (120 kW). Analysis of greenhouse gas (GHG) emissions generated during the production and use of semi-natural grassland fuels with IFBB technology was not covered in this study. However, it has been found that there is GHG savings of almost 3 t CO2-eq ha −1 for the prototype scale and a saving of almost 44 GJ ha −1 through the substitution of fossil fuel-based energy [31]. The GHG emissions can be attributed mainly to the heat, electricity, and fuel input during both the field operations and the IFBB process steps. Analysis of greenhouse gas (GHG) emissions generated during the production and use of seminatural grassland fuels with IFBB technology was not covered in this study. However, it has been found that there is GHG savings of almost 3 t CO2-eq ha −1 for the prototype scale and a saving of almost 44 GJ ha −1 through the substitution of fossil fuel-based energy [31]. The GHG emissions can be attributed mainly to the heat, electricity, and fuel input during both the field operations and the IFBB process steps.

Comparison between Commercial-Scale Plant and Prototype
In the commercial scale IFBB process (CS), most harmful elements were reduced to a greater extent than in the prototype scale process (PT) (Figure 4). For example, the overall ash reduction was 51.6% in CS compared to 30.2% in PT. Even though Cl concentrations in the press cakes were similar for both CS and PT, the reduction rate of Cl in CS was higher (89.4%) than in PT (81.1%). K was

Comparison between Commercial-Scale Plant and Prototype
In the commercial scale IFBB process (CS), most harmful elements were reduced to a greater extent than in the prototype scale process (PT) (Figure 4). For example, the overall ash reduction was 51.6% in CS compared to 30.2% in PT. Even though Cl concentrations in the press cakes were similar for both CS and PT, the reduction rate of Cl in CS was higher (89.4%) than in PT (81.1%). K was reduced by 88.5% in CS compared to 73.7% in PT and S was reduced by 62.3% in CS, which is a significantly (p < 0.001) higher reduction compared to 34.55% in PT. More than 90% of the elements Cl and K in biomass are present in the form of water-soluble free ions (Cl − , KNO 3 , and KCl, respectively) [58]. The improved reduction rate in CS may be explained by the higher quantity of water used and extended retention time in the mashing stage, and by the different mashing technique itself (mixing in water in CS compared to sprinkling with water on a conveyor belt in PT). The concentration of N in the fuel was reduced by 42.2% in CS compared to only 17.5% in PT. Substantial parts of N contained in herbaceous biomass can be presumed to be firmly bound in the cell wall proteins, which is not easily mobilizable with the IFBB procedure [26]. Due to lower N concentrations in the fuel the combustion of solid fuel from CS can be expected to generate lower NO x emissions compared to other herbaceous biomass. The difference in mean concentration of P in CS and PT solid fuel was low, but the reduction rate was higher for CS at 72.2% compared to 58.2% for PT. Concentrations of Ca in solid fuels were similar, as were the reduction rates both for CS and PT. The presence of Ca in the solid fuel during combustion has a positive influence on the ash melting temperature [21], hence, the moderately lower reduction of Ca compared to other elements is favorable for solid fuel production. In terms of element reduction, the commercial-scale is a clear improvement compared to the prototype scale, regardless of the variation in biomass being used.
Ash softening temperature of solid fuel in CS was 1163 • C compared to 1050 • C in PT, which cannot be fully attributed to scaling effects, as AST in CS silage was also higher. The improvement in AST between silage and solid fuel for both CS and PT were similar (10%) and for AFT the trend was similar, with 1335 • C for CS and 1290 • C for PT, but the rate of increase in both cases was only 3%. While element concentrations in the silages were very variable, the variation in the solid fuel was much smaller, proving the ability of a commercial-scale IFBB plant to convert a very heterogeneous biomass into a more homogeneous fuel. Nowadays, renewable energy sources such as wind and solar face the challenge of balancing energy demand with weather dependent fluctuation of energy production, therefore flexible power generation sources that are less dependent on weather can be used to cope up with the electricity demand. Biogas can be used for flexible power generation where the electricity generation can be managed to meet the electricity demand, especially if an easily digestible substrate such as the IFBB press liquid is used for biogas production [59,60].  Ash softening temperature of solid fuel in CS was 1163 °C compared to 1050 °C in PT, which cannot be fully attributed to scaling effects, as AST in CS silage was also higher. The improvement in AST between silage and solid fuel for both CS and PT were similar (10%) and for AFT the trend was similar, with 1335 °C for CS and 1290 °C for PT, but the rate of increase in both cases was only 3%.

Conclusions
Combusting green and leafy grassland biomass is not feasible due to the presence of harmful elements (mainly minerals and N) and their effect on fuel properties, combustion process, and emissions. The presented results from an up-scaled IFBB process confirmed recent research on a laboratory and prototype scale: concentration of detrimental constituents in fuels were drastically reduced compared to the parent material and ash melting behavior was improved in comparison to silage. Emissions during combustion were within the stipulated thresholds, except for PM, which is of no concern, as efficient filtering systems are common standard. The practical implementation will be facilitated, as the fuels produced are compatible with standard biomass or wood-chip boilers.
Solid fuels, being a flexible power source that can be easily stored, may be a vital component of a future renewable energy system that can help mitigate the fluctuations caused by natural restrictions while generating power using solar and wind, especially in remote locations where other energy generation options are difficult.
Therefore, using green residual biomass from grasslands and landscape management with the IFBB technology generates an energy carrier which (i) does not conflict with other biomass uses, (ii) mitigates CO 2 emissions, and (iii) helps to preserve landscape diversity.

Funding:
We would like to thank the EU for financing the COMBINE project (No. 299J) and DANUBENERGY project (No. 4CE561P3) through the Interreg IV B regional development fund. G-grasses, Sedges/Rushes-S/R, L-Legumes, H-Herbs, T-Total.