Limitations and Constraints of Eddy-Current Loss Models for IPM Motors with Fractional-Slot Concentrated Windings

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.


Introduction
In interior permanent-magnet motors (IPMs), the permanent magnets (PMs) are embedded into the rotor.Compared to rotors with surface-mounted PMs, the resulting flux concentration effect in IPMs significantly reduces the induced PM eddy-current losses caused by the changing air-gap permeance due to the slot openings.Further, a not insignificant magnetic saliency can be realized, which contributes with a reluctance torque component and thereby increases the torque density.These are two main reasons why the IPM is a common machine topology when targeting automotive applications, with recent examples including [1][2][3][4][5][6][7].
A fractional-slot concentrated winding (FSCW) enables very short end-winding lengths and, thereby, potential improvements in terms of torque density.However, depending on the combination of the number of stator slots Q s and poles p, the resulting harmonic content in the air-gap magnetomotive force (MMF) caused by the stator currents can be substantial.During the last decade, efforts were put into identifying suitable combinations of Q s and p where the impact of the stator MMF harmonics is as small as possible [8][9][10].Particularly, for rotors with surface-mounted PMs, a number of models to quantify the induced eddy-current losses in the PMs based on the harmonic content in the stator MMF were developed [11][12][13][14].Today, the combinations of Q s and p with the lowest harmonic content have been identified, and FSCWs are adopted in automotive applications (see, e.g., [15] and the references in [16]).
However, while the above loss models indeed are useful, they are most suitable for comparing the relative change in eddy-current losses for different combinations of Q s and p rather than accurately predicting the losses for given PM dimensions.Particularly, the effect of segmentation of the magnets and the impact of the skin effect is challenging.Additionally, these models target surface-mounted PMs rather than IPMs.Having a good approximation of the resulting PM losses is important for the 2 of 20 machine designer since relatively small losses in the PMs can result in excessive temperatures due to the difficulty of transferring the resulting heat across the air gap.
However, while the above loss models indeed are useful, they are most suitable for comparing the relative change in eddy-current losses for different combinations of Q s and p rather than accurately predicting the losses for given PM dimensions.Particularly, the effect of segmentation of the magnets and the impact of the skin effect is challenging.Additionally, these models target surface-mounted PMs rather than IPMs.Having a good approximation of the resulting PM losses is important for the machine designer since relatively small losses in the PMs can result in excessive temperatures due to the difficulty of transferring the resulting heat across the air gap.Essentially, predicting the losses in the PMs can be done accurately using three-dimensional (3D) finite-element (FEM) based simulations (as demonstrated in [17]).However, the approach must still be considered relatively time consuming although efforts have been made to reduce the computation times [18].Recently, the relatively simple analytical loss model in [19] was proposed considering FSCWs with surface-mounted PMs and including the effect of both axial and tangential segmentation of the PMs.This model uses the stator MMF harmonic content as input but neglects the impact of the skin effect.A more advanced model, incorporating the effect of axial and tangential segmentation as well as the skin effect, is adopted in [20] where analytical solutions of Helmholtz equation with an imposed source term are adopted.A different model (also accounting for segmentation and the skin effect) is adopted in [21] where solutions to Helmholtz equation with a prescribed boundary surface current are used.

Contributions and Outline of Paper
An overall aim of this work is to provide a link between models describing the harmonic content in FSCWs due to the stator MMF with corresponding, sufficiently accurate PM eddy-current loss models for IPMs.Particularly, the loss models in [20] (here designated Model B) and [21] (here designated Model C), adopting solutions to different formulations of Helmholtz equation to solve for the eddy currents, are compared to the considerably less complex loss model in [19] (here adapted to IPMs and designated Model A).It is demonstrated that Model B and Model C, though considerably different in terms of implementation complexity, predict very similar results (in good agreement with corresponding 3D-FEM simulations) for PM dimension and rotor speed intervals typically found in automotive applications.Further, limits (in terms of frequency and PM dimensions) where Model A (the least complex loss model) is applicable are identified numerically and using an approximate analytical expression.This limit is not straight forward since the rectangular shape of the PM segments results in complex eddy-current reaction fields.Key concepts regarding FSCWs are included as an appendix representing a complete description on how the uniform variation of the flux density in the PMs can be analytically predicted.The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets.An extensive numerical evaluation using 3D-FEM based simulations is carried Essentially, predicting the losses in the PMs can be done accurately using three-dimensional (3D) finite-element (FEM)-based simulations (as demonstrated in [17]).However, the approach must still be considered relatively time consuming, although efforts have been made to reduce the computation times [18].Recently, the relatively simple analytical loss model in [19] was proposed considering FSCWs with surface-mounted PMs and including the effect of both axial and tangential segmentation of the PMs.This model uses the stator MMF harmonic content as input, but neglects the impact of the skin effect.A more advanced model, incorporating the effect of axial and tangential segmentation, as well as the skin effect, is adopted in [20] where analytical solutions of the Helmholtz equation with an imposed source term are adopted.A different model (also accounting for segmentation and the skin effect) is adopted in [21], where solutions to the Helmholtz equation with a prescribed boundary surface current are used.

Contributions and Outline of the Paper
An overall aim of this work is to provide a link between models describing the harmonic content in FSCWs due to the stator MMF with corresponding, sufficiently accurate PM eddy-current loss models for IPMs.Particularly, the loss models in [20] (here designated Model B) and [21] (here designated Model C), adopting solutions to different formulations of the Helmholtz equation to solve for the eddy currents, are compared to the considerably less complex loss model in [19] (here adapted to IPMs and designated Model A).It is demonstrated that Model B and Model C, though considerably different in terms of implementation complexity, predict very similar results (in good agreement with corresponding 3D-FEM simulations) for the PM dimension and rotor speed intervals typically found in automotive applications.Further, limits (in terms of frequency and PM dimensions) where Model A (the least complex loss model) is applicable are identified numerically and using an approximate analytical expression.This limit is not straight forward since the rectangular shape of the PM segments results in complex eddy-current reaction fields.Key concepts regarding FSCWs are included as an Appendix representing a complete description of how the uniform variation of the flux density in the PMs can be analytically predicted.The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets.An extensive numerical evaluation using 3D-FEM-based simulations is carried out to verify model assumptions and and the conclusions made regarding whether each loss model is applicable or not.The comparison with 3D-FEM results represents a solid evaluation metric since 3D-FEM-based models of PM eddy-current losses previously have been demonstrated to yield good agreement 3 of 20 with corresponding experimental results (see, e.g., [17,21]).Further, the extent of a corresponding experimental evaluation would be extremely expensive in order for a realization where a sufficiently large number of parameters (including PM, stator and rotor dimensions) would be varied.
The paper is outlined as follows.In Section 2, the loss models considered are briefly reviewed where the loss model in [19] (here designated Model A), but adapted to IPMs, is presented.In Section 3 (being the major part of this paper), model constraints when applied to IPM rotor geometries and the model limitations for Model A due to eddy-current reaction fields are identified.These constraints and limitations are also verified with presented 3D-FEM-based models.Finally, predicted magnet losses and temperature risk indicators are tabulated for combinations of Q s and p that are commonly considered in automotive applications in Section 4, and concluding remarks are given in Section 5.

Review of Eddy-Current Loss Models
For axially short PMs and assuming a sinusoidal flux-density variation, the predicted volumetric loss density p m (W/m 3 ) (presented in textbooks, e.g., [22,23]) can be expressed as: where σ m is the conductivity of the PMs, l m the axial length of the PM and ω ν m and B ν m are the angular frequency and magnitude of the imposed flux density, respectively.However, the assumption of axially short PMs is not valid for practical axial segmentation lengths, and (1) cannot be directly applied.Generally, assuming constant µ r and neglecting displacement currents (i.e., ∂D/d∂t ≈ 0), the magnetic field in the PMs follows the Helmholtz equation, which can be expressed as: Once a solution to (2) is determined, the current density (and associated losses) can be found from: In both (2) and (3), bold symbols denote vector fields, and the bar above denotes a phasor (complex) quantity.Solutions to (2) are used for loss Model B and Model C reviewed below.

Model A: Assumed Eddy-Current Paths [19]
The loss model presented in [19] is developed for surface-mounted rotors where the air-gap flux-density harmonics passes over each permanent magnet segment depending on the rotor speed and wavelength of each harmonic.For IPMs, however, the flux concentration assumed in (A11) results only in a time-dependent variation of the flux density in the PMs.In [19], this corresponds to the case of an infinite wavelength where the assumed eddy-current paths are illustrated in Figure 2.
From Figure 2, the flux in the assumed eddy-current path φ can be expressed as: The losses in the specific eddy-current path dP m can then be expressed as: where R EC is the resistance of the eddy-current path found as: Figure 2. Assumed eddy-current paths adopted in Model A [19].
The average magnet losses for an elementary current path dP m,ave (which is a function of x and y ) is now found by integrating (5) as: Finally, an expression for the total average magnet losses for a magnet segment is now found as: where y = l m x /w m is used when evaluating the integral.
Remark 1.Note that for axially short PMs (l m w m ), the volumetric loss density p m using (8) is found as: which is not in agreement with (1).From (9), it can, hence, be expected that Model A will underestimate the eddy current losses if the PMs are axially short.
Remark 2. Similar loss models also adopting prescribed eddy-current paths are presented in [24].
2.2.Model B: Solving the Helmholtz Equation with the Imposed Source Term [25] In [25], the Helmholtz equation is solved where the source field due to the armature reaction is added explicitly rather than as an imposed boundary condition.With this source term added, (2) becomes: Similar solutions are reported in [20,26] where in [20], the solution is applied on two IPMs with distributed windings.The resulting average eddy-current losses for a magnet segment become [20]: where h m δ was assumed in the approximation used in (13).
Remark 3.For axially short PMs; using (11), the volumetric loss density p m is found as: Now, the double sum in ( 14) equals π 6 /768 (obtained using Mathematica (Mathematica is a registered trademark of Wolfram Research, Inc., Champaign, IL, USA)), which yields an expression for p m identical to (1).

Model C: Solving the Helmholtz Equation Prescribing Boundary Surface Currents [21,27]
As is well known, the magnetization of a PM can be represented using a surface-current density with a magnitude corresponding to the remanent flux density divided by the permeability (see, e.g., [23]).Therefore, each flux density harmonic caused by the armature reaction can, approximately, be modeled assuming the surface current: on the outer boundaries of the magnet segment whose normals are in the xy-plane (the xy-coordinate system is depicted in Figure A1).Equation (2) simplifies to: with the boundary condition H z = B ν m /(µ 0 µ r ) on the prescribed outer boundaries.
A general solution to (16) with the given boundary condition is presented in [21,27] where in [27], also the displacement currents are accounted for.From the solution H z (x, y), the current density is then found as: The resulting expression for the average eddy-current losses for a magnet segment becomes: where m = 2p − 1, n = 2q − 1, and: Remark 4. It is further shown in [27] that using (18), the resulting volumetric loss density p m for axially short PMs is identical to the classical expression (1).

Loss-Model Constraints When Applied to IPMs
An analytical approach for approximating the flux-density variation B m (θ r ) in the PMs as a function of rotor position θ r is outlined in Section A.4 in the Appendix.From B m (θ r ), the corresponding harmonics (of order ν m and with a magnitude B ν m ) can then be identified (in this paper, this identification has been done using the fft function in MATLAB (MATLAB is a registered trademark of The Mathworks Inc., Natick, MA, USA)).However, if required, more accurate predictions of B ν m can rapidly be obtained using two-dimensional static FEM simulations.
The three eddy-current loss models reviewed in Section 2 all assume that the flux density variation in the PMs is uniform.For surface-mounted PMs, it is pointed out in [19] that such an assumption holds provided that the PM width w m is significantly lower than half of the wavelength λ ν of the harmonic order of most interest ν.
With the pole-cap coefficient α p as defined in Figure A1, for IPMs, the corresponding condition can be expressed as α p /(Cp) ≤ 1/ν where C = 1 and C = 1/2 for V-shaped and straight interior PMs, respectively.For many combinations of Q s and p, the harmonic order ν that dominates the PM losses is less than or equal to p (i.e., ν ≤ p).Further, α p ≈ 3/4 is not uncommon in order to realize a certain reluctance-torque component.Thereby, we obtain: and it can be concluded that for V-shaped PMs, a uniform flux-density variation in the PMs can often be assumed, whereas for straight interior PMs, this assumption is valid only if the harmonic order ν that dominates the PM losses fulfills ν p.

Limits for Model A Due to Eddy-Current Reaction Fields
As seen, the expressions for the volumetric loss density p m given by Model A, Model B and Model C are of increasing complexity.An interesting issue is therefore to determine the boundaries when the simplest model (Model A) is applicable.Since Model A does not incorporate the effect of eddy-current reaction fields, it may risk overestimating the eddy-current losses at higher frequencies.However, as pointed out in (9), Model A will underestimate the eddy-current losses if either l m w m or w m l m (where both Model B and Model C simplify to (1), as shown by (14) and in [27], respectively).
To compare Model B and Model C to Model A for typical PM dimensions l m and w m , the relative errors ε A|B and ε A|C are therefore introduced as: In Figure 3, contours when ε A|B = 0.2 (representing a modest deviation) have been plotted for ω ν m /(2π) = 300 Hz to ω ν m /(2π) = 3000 Hz in steps of 300 Hz assuming µ r = 1.04 and σ m = 694 kS/m (typical values for PMs of the NdFeB-type).The regions representing l m w m or w m l m are patched as black in Figure 3.It is further found that the contours for ε A|C = 0.2 are essentially identical.Hence, Model B should predict very similar results to (the somewhat more complex) Model C. How Figure 3 (or its approximation Figure 4 (see below)) can be used by the machine designer to determine the validity of the different loss models is exemplified in Section 3.3.

Limits for Model A Due to Eddy-Current Reaction Fields
As seen, the expressions for the volumetric loss density p m given by Model A, Model B, and Model C, are of increasing complexity.An interesting issue is therefore to determine the boundaries when the simplest model (Model A) is applicable.Since Model A does not incorporate the effect of eddy-current reaction fields, it may risk to overestimate the eddy-current losses at higher frequencies.However, as pointed out in (9), Model A will underestimate the eddy-current losses if either l m ≪ w m or w m ≪ l m (where both Model B and Model C simplify to (1) as shown by (14) and in [27], respectively).
To compare Model B and Model C to Model A for typical PM dimensions l m and w m , the relative errors ε A|B and ε A|C are therefore introduced as In Figure 3, contours when ε A|B = 0.2 (representing a modest deviation) have been plotted for

Approximation of ε A|B
Figure 3 can be useful for a machine designer since it provides boundaries in terms of magnet dimensions l m and w m and excitation frequencies ω ν m when the simplest loss model (Model A) predicts the resulting eddy-current losses with sufficient accuracy.In [27], a number of approximations to (18) (Model C) are presented.However, when applying these approximation using typical PM dimensions (l m and w m ) and a conductivity σ m valid for NdFeB-type PMs, it is found that none of the resulting approximations to ε A|C reproduce the contours in Figure 3 sufficiently accurately.
In order to investigate whether ε A|B can be approximated, the dimensional ratios ξ and κ are introduced as: κ = min(l m , w m ) δ skin (25) where δ skin = 2/(σ m µ 0 µ r ω ν m ) is the classical expression for skin depth.Now, by considering only n = m = 1 in (11), ε A|B can be approximated as: The contours for ε A|B = 0.2 using the approximation (26) are plotted in Figure 4. Comparing Figures 3 and 4, it can be seen that ( 26) represents the model prediction error reasonably well.
In order to investigate whether ε A|B can be approximated, the dimensional ratios ξ and κ are introduced as κ = min(l m , w m ) δ skin (25) where δ skin = 2/(σ m µ 0 µ r ω ν m ) is the classical expression for skin depth.Now, by considering only n ′ = m ′ = 1 in (11), ε A|B can be approximated as The contours for ε A|B = 0.2 using the approximation (26) are plotted in Figure 4. Comparing Figure 3 and Figure 4, it can be seen that ( 26) represents the model prediction error reasonably well.

3DFEM-Evaluation
In order to verify the boundary constraints identified in Sections 3.1 and Section 3.2, comparisons with corresponding 3D-FEM based models, implemented using JMAG 3 , are now presented.In the 3D-FEM based model, the eddy-current losses have been obtained by computing the average value of the Ohmic losses in a PM segment (caused by the resulting current density distribution).
A three-phase IPM with Q s = 12 slots and p = 8 poles with additional key parameters reported in Table B.1 in Appendix B is used initially for evaluation.The machine geometry is depicted in Figure 5 (a) and the PM width is w m = 15 mm and the axial length of the PM is varied so that l m = 10, 30, and 100 mm, respectively.The rotor speed is varied up to 9000 rpm.
A brief review of the fundamentals of the resulting harmonic content is provided in Appendix A.
From (29), the winding periodicity is found as t per = 4. Therefore, from (32), the harmonic orders that 3 JMAG is a registered trademark of the JSOL Corporation, Tokyo, Japan.

3DFEM-Evaluation
In order to verify the boundary constraints identified in Sections 3.1 and 3.2, comparisons with corresponding 3D-FEM-based models, implemented using JMAG (JMAG is a registered trademark of the JSOL Corporation, Tokyo, Japan), are now presented.In the 3D-FEM-based model, the eddy-current losses have been obtained by computing the average value of the Ohmic losses in a PM segment (caused by the resulting current density distribution).
A three-phase IPM with Q s = 12 slots and p = 8 poles with additional key parameters reported in Table A1 in Appendix B is used initially for evaluation.The machine geometry is depicted in Figure 5a; the PM width is w m = 15 mm, and the axial length of the PM is varied so that l m = 10, 30 and 100 mm, respectively.The rotor speed is varied up to 9000 rpm.
A brief review of the fundamentals of the resulting harmonic content is provided in Appendix A. From (A1), the winding periodicity is found as t per = 4. Therefore, from (A4), the harmonic orders that could be present in the air gap due to the armature reaction (assuming sinusoidal phase currents) are ν = 4, 8, 12, 16, 20, . ... However, from (A6), k ν = 0 for harmonics that are multiples of 12.The magnitude of the corresponding harmonics can be obtained using (A3)-(A9).Hence, in the air gap, the three first harmonic orders are ν = 4, 8 and 16.For the considered rotor structures, α p ≈ 0.77 and using (A5) and (A12), the first harmonic order present in a PM is ν m = 12 (higher order harmonics exist, but could be present in the air gap due to the armature reaction (assuming sinusoidal phase currents) are ν = 4, 8, 12, 16, 20, . ... However, from (34), k ν = 0 for harmonics that are multiples of 12.The magnitude of the corresponding harmonics can be obtained using ( 31)-(37).Hence, in the air gap, the three first harmonic orders are ν = 4, 8, and 16.For the considered rotor structures, α p ≈ 0.77 and using (33) and (40), the first harmonic order present in a PM is ν m = 12 (higher order harmonics exist but are of significantly lower magnitude and contribute only minor to the total eddy-current losses).
Remark: Since the PMs are mounted in the interior of the rotor, the resulting eddy-current losses due to the slot-opening effect is negligible compared to the eddy-current losses due to the armature reaction.

Negligible Eddy-Current Reaction Fields
The considered three PM dimensions are indicated in Figure 3 as black diamonds (⋄).As seen, for 1800 Hz, all three PM dimensions fall within the set of l m and w m for which Model A should provide an accurate prediction (i.e., a deviation of at most 20 %).This is verified in Figure 6 where it can be seen that Model A predicts similar results as Model B (red lines) and Model C (green lines) in V-shaped interior PMs (w m = 15 mm) with different magnet lengths l m , and also agrees with the corresponding 3D-FEM results.

Non-Negligible Eddy-Current Reaction Fields
With a wider magnet width w m = 30 mm (see Figure 5 (b)), it can be seen from Figure 3 (depicted as a blue circle (•)) that Model A will overestimate the eddy-current losses for frequencies above around 1700 Hz (corresponding to rotor speeds around 8500 rpm).This is verified in Figure 7 where the losses are substantially overestimated at speeds above (around) 8500 rpm.Compensating Model A as P m / ε A|B + 1 using the approximation of ε A|B given by ( 26) yields a significantly better agreement with the corresponding 3D-FEM results.Model B and Model C predict similar results, both agreeing well the corresponding 3D-FEM results at all rotor speeds considered.Remark 5. Since the PMs are mounted in the interior of the rotor, the resulting eddy-current losses due to the slot-opening effect are negligible compared to the eddy-current losses due to the armature reaction.

Negligible Eddy-Current Reaction Fields
The considered three PM dimensions are indicated in Figure 3 as black diamonds ( ).As seen, for 1800 Hz, all three PM dimensions fall within the set of l m and w m for which Model A should provide an accurate prediction (i.e., a deviation of at most 20%).This is verified in Figure 6, where it can be seen that Model A predicts similar results as Model B (red lines) and Model C (green lines) in V-shaped interior PMs (w m = 15 mm) with different magnet lengths l m and also agrees with the corresponding 3D-FEM results.3) is wider than half of the 178 dominant harmonic's wavelength λ ν .Therefore, the flux-density variation is not uniform and the 179 loss prediction accuracy for all three models worsens.This is verified in Figure 8 where neither of the 180 models are in agreement with the corresponding 3D-FEM results.

Visualization of Resulting Eddy-Current Distribution 182
As is well known, the time-dependent currents densities found from the time-harmonic (complex) formulations used in Model B and Model C can be determined as Figure 9 shows the resulting eddy-current distributions in a PM segment of the IPM depicted in

Non-Negligible Eddy-Current Reaction Fields
With a wider magnet width w m = 30 mm (see Figure 5b), it can be seen from Figure 3 (depicted as a blue circle (•)) that Model A will overestimate the eddy-current losses for frequencies above around 1700 Hz (corresponding to rotor speeds around 8500 rpm).This is verified in Figure 7 where the losses are substantially overestimated at speeds above (around) 8500 rpm.Compensating Model A as P m / ε A|B + 1 using the approximation of ε A|B given by ( 26) yields a significantly better agreement with the corresponding 3D-FEM results.Model B and Model C predict similar results, both agreeing well with the corresponding 3D-FEM results at all rotor speeds considered.Peer-reviewed version available at Energies 2017, 10, 379; doi:10.3390/en10030379Remark 6.Since the PMs are buried very deep into the rotor structure, (A11) represents an overly simplistic approach for predicting the flux-density variation (while still being relatively uniform).Therefore, for this case only, the actual flux density B m (θ r ) is extracted from static 2D-FEM models.

Impact of Non-Uniform Flux-Density Variation
Following the discussion in Section 3.1, the magnet width w m for the straight IPM depicted in Figure 5c (PM dimensions marked as the red square ( ) in Figure 3) is wider than half of the dominant harmonic's wavelength λ ν .Therefore, the flux-density variation is not uniform, and the loss prediction accuracy for all three models worsens.This is verified in Figure 8 where neither of the models are in agreement with the corresponding 3D-FEM results.Predicted distributions using Model B (red contours) and Model C (green contours).First, it is noted that the resulting eddy-current distributions predicted by the two models are essentially equal.Hence, both models can be expected to predict similar eddy-current losses.Further, at 1000 rpm, the eddy current distribution is very similar to what is assumed in Model A (compare with Figure 2).However, at higher speeds, the eddy current paths during the transition between "clockwise" and "anti-clockwise" current paths becomes more complex with additional eddies close to corners.Corresponding 3D-FEM results are depicted in Figure 10 and, as seen, the eddy-current distributions predicted with Model B and Model C are in good agreement with the 3D-FEM results.
In Figure 11, the predicted current densities |J| = J 2 x + J 2 y at 15000 rpm in selected positions 'Pa' and 'Pb' (see Figure 9 (b)) using Model A, Model B, Model C, and corresponding 3D-FEM results are reported.As seen, Model B and Model C are agreeing well with the 3D-FEM based results whereas Model A overestimates the eddy-currents significantly.

Thermal Impact
While Figure 3 or its approximation (26) provide necessary input on which loss model is suitable, the associated temperature increase in the PMs (due to the eddy currents) represents a key limiting factor for the machine designer.To investigate this thermal impact, a set of 3D-FEM thermal simulations of the machine described above are carried out at 9000 rpm and rated current for different volumetric loss densities p m in the PMs.The implemented thermal model is similar to the 3D-FEM

Visualization of the Resulting Eddy-Current Distribution
As is well known, the time-dependent currents densities found from the time-harmonic (complex) formulations used in Model B and Model C can be determined as: J y (t) = J y cos (ω ν m t) − J y sin (ω ν m t) .( Figure 9 shows the resulting eddy-current distributions in a PM segment of the IPM depicted in Figure 5b for two different speeds (1000 and 15,000 rpm) with a PM segment length l m = 60 mm; predicted distributions using Model B (red contours) and Model C (green contours).First, it is noted that the resulting eddy-current distributions predicted by the two models are essentially equal.Hence, both models can be expected to predict similar eddy-current losses.Further, at 1000 rpm, the eddy current distribution is very similar to what is assumed in Model A (compare with Figure 2).However, at higher speeds, the eddy current paths during the transition between "clockwise" and "anti-clockwise" current paths becomes more complex with additional eddies close to corners.Corresponding 3D-FEM results are depicted in Figure 10, and as seen, the eddy-current distributions predicted with Model B and Model C are in good agreement with the 3D-FEM results.
In Figure 11, the predicted current densities |J| = J 2 x + J 2 y at 15, 000 rpm in selected positions 'Pa' and 'Pb' (see Figure 9b       3D-FEM thermal simulation is depicted in Figure 12 and the resulting PM temperatures are reported in Figure 13.The results in Figure 13 will be used below in order to provide approximate intervals of p m which potentially can result in excessive PM temperatures in an automotive application.

Losses for p and Q s Common in Automotive Applications
Now, resulting PM eddy-current losses for combinations of p and Q s often considered in automotive applications are considered.The harmonic content from double-layer FSCWs are considered in this paper.For single-layer FSCWs, the harmonic content is described in [8,12,14].The rotor radius r r and air-gap length δ are selected identical to what reported in Table B.1 and the main harmonic stator MMF (the ampere-turns and winding factor k ν=p/2 product) is also kept the same meaning that each resulting machine design results in a similar output torque (the harmonic content will be different, however, for each combination of p and Q s ).The pole-cap coefficient is selected to α p = 3/4 to yield a rotor saliency and the PM height is selected to h m = 5 mm.Further, the PM width w m is selected so that the no-load flux density in the air gap is 0.75 T. For p = 8, 10, 12, and 14, this results in w m = 14.2, 11.3, 9.5, and 8.1 mm.Resulting rotor geometries for p = 8 and p = 14 (with magnetic bridges and air pockets inserted) are depicted in Figure 14.
The resulting PM loss densities for l m = 10 mm and l m = 30 mm are reported in Table 1 and Table 2, respectively.As seen, only a few combinations of p and Q s result in sufficiently low eddy-current losses so that excessive PM temperatures are avoided.Also, the increase of PM length from l m = 10 mm to l m = 30 mm rules out all but two combinations of p and Q s .Further, the loss densities reported in Table 1 and Table 2 are predictions using Model C.However, using Figure 3 or its approximation (26), it can be determined that Model A provides sufficient accuracy (i.e., within a 20% deviation from Model B and Model C) for all cases considered in Table 1 and Table 2.

Thermal Impact
While Figure 3 or its approximation (26) provide necessary input on which loss model is suitable, the associated temperature increase in the PMs (due to the eddy currents) represents a key limiting factor for the machine designer.To investigate this thermal impact, a set of 3D-FEM thermal simulations of the machine described above is carried out at 9000 rpm and rated current for different volumetric loss densities p m in the PMs.The implemented thermal model is similar to the 3D-FEM thermal model described in [28], and the intention is to determine approximately how different values of p m correspond to resulting magnet temperatures.The iron losses in the stator and rotor laminations are computed using the in-built loss model in JMAG.The winding, including the end-winding part, is impregnated in epoxy with an assumed effective thermal conductivity of 0.68 W/(m•K).The outer surface of the stator lamination is fixed to 60 • C representing a water cooling jacket with a coolant temperature typical of what is found in automotive applications.A sample result from the 3D-FEM thermal simulation is depicted in Figure 12, and the resulting PM temperatures are reported in Figure 13.The results in Figure 13 will be used below in order to provide approximate intervals of p m , which potentially can result in excessive PM temperatures in an automotive application.

Losses for p and Q s Common in Automotive Applications
Now, resulting PM eddy-current losses for combinations of p and Q s often considered in automotive applications are considered.The harmonic content from double-layer FSCWs is considered in this paper.For single-layer FSCWs, the harmonic content is described in [8,12,14].The rotor radius r r and air-gap length δ are selected identical to what is reported in Table A1, and the main harmonic stator MMF (the ampere-turns and winding factor k ν=p/2 product) is also kept the same, meaning that each resulting machine design results in a similar output torque (the harmonic content will be different, however, for each combination of p and Q s ).The pole-cap coefficient is selected as α p = 3/4 to yield a rotor saliency, and the PM height is selected as h m = 5 mm.Further, the PM width w m is selected so that the no-load flux density in the air gap is 0.75 T. For p = 8, 10, 12 and 14, this results in w m = 14.2, 11.3, 9.5 and 8.1 mm.Resulting rotor geometries for p = 8 and p = 14 (with magnetic bridges and air pockets inserted) are depicted in Figure 14.
The resulting PM loss densities for l m = 10 mm and l m = 30 mm are reported in Tables 1 and 2, respectively.As seen, only a few combinations of p and Q s result in sufficiently low eddy-current losses so that excessive PM temperatures are avoided.Furthermore, the increase of PM length from l m = 10 mm to l m = 30 mm rules out all but two combinations of p and Q s .Further, the loss densities reported in Tables 1 and 2 are predictions using Model C.However, using Figure 3 or its approximation (26), it can be determined that Model A provides sufficient accuracy (i.e., within a 20% deviation from Model B and Model C) for all cases considered in Tables 1 and 2.

Conclusions
In this paper, three models for predicting average magnet losses in IPMs with FSCWs due to induced eddy currents caused by the armature reaction (assuming sinusoidal phase currents) were analyzed and compared.Provided that the harmonic order ν that dominates the PM losses is less or equal to the number of poles p, it was found that that for V-shaped PMs, a uniform flux density variation in the PMs can typically be assumed.Boundaries in terms of PM dimensions and angular frequency were identified to aid the machine designer to decide whether the simplest loss model (Model A) is applicable or not.An approximate analytical expression to these boundaries was also identified.It was found that Model B and Model C, while relying on different formulations and solutions of the Helmholtz equation, provide very similar loss predictions in very good agreement with corresponding 3D-FEM-based simulations.Further, tables were provided with resulting volumetric loss densities p m for combinations of Q s and p commonly used in automotive applications.Finally, by compiling results from previous publications, a complete description on how to analytically predict the magnitudes B ν m and corresponding harmonic orders ν m for FSCW-IPMs was provided in the Appendix.
ω ν m /(2π) = 300 Hz to ω ν m /(2π) = 3000 Hz in steps of 300 Hz assuming µ r = 1.04 and σ m = 694 kS/m (typical values for PMs of NdFeB-type).The regions representing l m ≪ w m or w m ≪ l m are patched as black in Figure3.It is further found that the contours for ε A|C = 0.2 and essentially identical.Hence, Model B should predict very similar results to (the somewhat more complex) Model C. How Figure3(or its approximation Figure4(see below)) can be used by the machine designer to determine validity of the different loss models are exemplified in Section 3.3.

PreprintsFigure 6 .
Figure 6.Predicted losses per magnet segment P m as function of rotor speed and for different magnet lengths l m in V-shaped interior PMs (w m = 15 mm) for Model A (blue line), Model B (red line), Model C (green line), and corresponding 3D-FEM results (diamonds "⋄"): (a) l m = 10 mm; (b) l m = 30 mm; (c) l m = 100 mm.

Figure 5 (Figure 6 .
Figure 5 (b) for two different speeds (1000 and 15000 rpm) with a PM segment length l m = 60 mm.184

Figure 7 .Figure 7 .
Figure 7. Predicted losses per magnet segment P m as function of rotor speed and for magnet lengths l m = 60 mm in V-shaped interior PMs (w m = 30 mm) for Model A (blue lines), Model A but compensated as P m /(ε A|B + 1) (dashed blue line), Model B (red line), Model C (green line), and corresponding 3D-FEM results (circles "•").

Figure 7 .Figure 8 .
Figure 7. Predicted losses per magnet segment P m as function of rotor speed and for magnet lengths l m = 60 mm in V-shaped interior PMs (w m = 30 mm) for Model A (blue lines), Model A but compensated as P m /(ε A|B + 1) (dashed blue line), Model B (red line), Model C (green line), and corresponding 3D-FEM results (circles "•").

Figure 8 .
Figure 8. Predicted losses per magnet segment P m as a function of rotor speed for l m = 60 mm for the straight IPM depicted in Figure 5 (c)s (w m = 40 mm) for Model A (blue line), Model B (red line), Model C (green line) and corresponding 3D-FEM results (squares " ").

Figure 9 .
Figure 9. Resulting eddy current distribution using Model B (red contours) and Model C (green contours) evaluated at ω ν m t = π/4 with a magnet length l m = 60 mm at two different speeds: (a) 1000 rpm; (b) 15000 rpm.Note that the green contours are almost completely covered by the red contours which indicates that the two models predict essentially the same eddy current distribution.

Figure 9 .Figure 9 .
Figure 9. Resulting eddy current distribution using Model B (red contours) and Model C (green contours) evaluated at ω ν m t = π/4 with a magnet length l m = 60 mm at two different speeds: (a) 1000 rpm; (b) 15,000 rpm.Note that the green contours are almost completely covered by the red contours, which indicates that the two models predict essentially the same eddy current distribution.

Figure 10 .
Figure 10.Resulting eddy current distribution from the 3D-FEM model evaluated at ω ν m t = π/4 with a magnet length l m = 60 mm at two different speeds: (a) 1000 rpm; (b) 15000 rpm.

245Figure 13 .
Figure 13.Resulting PM average temperature as a function of PM volumetric loss density p m at rated current and 9000 rpm.The considered low, medium and high temperature ranges have been indicated using green, orange and red colors, respectively.

Table 1 .
p m [W/cm 3 ] for l m = 10 mm at 9000 rpm

5. Conclusions 231
Provided that the harmonic order ν that dominates the PM losses is less 234 or equal to to the number of poles p, it was found that that for V-shaped PMs, a uniform flux 235 density variation in the PMs can typically be assumed.Boundaries in terms of PM dimensions In this paper, three models for predicting average magnet losses in IPMs with FSCWs due to 232 induced eddy currents caused by the armature reaction (assuming sinusoidal phase currents) were 233 analyzed and compared.

Table 2 .
p m [W/cm 3 ] for l m = 30 mm at 9000 rpm