Quantification of the Influence of Citrate/Fe(II) Molar Ratio on Hydroxyl Radical Production and Pollutant Degradation during Fe(II)-Catalyzed O2 and H2O2 Oxidation Processes

Ligand-enhanced hydroxyl radical (•OH) production is an important strategy for Fe(II)-catalyzed O2 and H2O2 oxidation processes. However, the influence of the molar ratio of ligands to Fe(II) on •OH production remains elusive. This study employed citrate and inorganic dissolved Fe(II) (Fe(II)dis) as the representative ligand and Fe(II) species, respectively, to quantify this relationship. Results showed that •OH production was highly dependent on the citrate/Fe(II) molar ratio. For instance, for the oxygenation of Fe(II)dis, the •OH accumulations were 2.0–8.5, 3.4–28.5 and 8.1–42.3 μM at low (0.25–0.5), moderate (0.5–1), and high (1–2) citrate/Fe(II) molar ratios, respectively. At low citrate/Fe(II) molar ratio (<0.5), inorganic Fe(II)dis mainly contributed to •OH production, with the increase in the citrate/Fe(II) molar ratio to a high level (1–2), Fe(II)-citrate complex turned to the electron source for •OH production. The change in Fe(II) speciation with the increase of citrate/Fe(II) molar ratio elevated •OH production. For pollutant degradation, 1 mg/L phenol was degraded by 53.6% within 40 min during oxygenation of Fe(II)-citrate system (1:1) at pH 7. Our results suggest that a moderate molar ratio of ligand/Fe(II) (0.5–1) may be optimal for Fe(II)-catalyzed O2 and H2O2 oxidation processes.


Introduction
Hydroxyl radical-based advanced oxidation process (HR-AOP) is considered to be an effective technology for the remediation of contaminated soil and groundwater [1]. The hydroxyl radical (•OH) is the most powerful oxidant in the natural system [2][3][4], capable of oxidizing most environmental pollutants, such as chlorinated hydrocarbons [5,6], antibiotic [7] and aromatic compounds [8][9][10]. Hydrogen peroxide (H 2 O 2 ) is the traditional source of •OH in HR-AOP, and recent studies showed that oxygen (O 2 ) can also act as a source of •OH in some specific conditions, for example, when the reduced soil or sediment was exposed to oxic conditions [1,6,7]. However, H 2 O 2 and O 2 cannot be spontaneously transformed to •OH in natural environments, requiring activation by chemical agents or physical treatments. Ferrous iron (Fe(II)) is the most commonly used and effective activator for H 2 O 2 and O 2 [1,11,12]. The Fe(II)-catalyzed H 2 O 2 oxidation process (i.e., Fenton reaction) has been widely used in contaminant remediation, such as in situ chemical oxidation projects and wastewater treatment [1,11]. In comparison, the Fe(II)-catalyzed O 2 oxidation process has been demonstrated to degrade pollutants only at the laboratory scale [5][6][7][8][9]13]. However, O 2 is cheaper and easier to obtain than H 2 O 2 , so the Fe(II)catalyzed O 2 oxidation process is also proposed as a promising method for pollutant degradation [1].

Oxic Experiments
A series of oxic experiments were used to explore the influence of citrate/Fe(II) molar ratio on •OH production and phenol degradation during the Fe(II)-catalyzed O 2 oxidation process. All oxic experiments were conducted at 25 ± 1 • C in 150-mL conical flasks that were wrapped with aluminum foil to avoid light. Teflon-coated magnetic stirring bars were used to keep the stirring speed at approximately 300 rpm. To initiate experiments, citrate concentrations of 62.5, 125, 250, and 500 µM were added to the solution containing 250 µM Fe(II) dis , 10 mM buffer (MES for pH 6 and PIPES for pH 7 and 7.5), 20 mM benzoate and 5 mM Na 2 SO 4 . Control experiments were carried out with the addition of inorganic Fe(II) dis alone under otherwise identical conditions.
During all of the above experiments, the change of solution pH was less than 0.1 and the dissolved O 2 (DO) concentration was maintained at near 0.25 mM. At predetermined times of reaction, approximately 1-mL sample was taken out for p-HBA, Fe(II) dis , Fe(III) dis and total Fe analysis. All experiments were performed in duplicate.

Anoxic Experiments
The anoxic experiments were used to explore the influence of citrate/Fe(II) molar ratio on •OH production during the Fe(II)-catalyzed H 2 O 2 oxidation process. A solution containing 250 µM inorganic Fe(II) dis , 20 mM benzoate and 10 mM buffer was first purged with N 2 (99.999%) for at least 1 h and then mixed with different concentrations of citrate (0, 62.5, 125, 250 and 500 µM) for 2 h in an anaerobic glovebox (95% N 2 and 5% H 2 , COY, USA). Finally, H 2 O 2 concentrations of 20, 40, 60, 80 and 100 µM were added to the above Fe(II)-citrate system. After a reaction of 30 min, a sample of approximately 1 mL was removed for p-HBA. Note that the residual concentration of H 2 O 2 in all experiments was less than 0.1 µM. These experiments were conducted at pH 6, 7 and 7.5.

Analysis
For the analysis of the p-HBA concentration, a sample of approximately 0.8 mL was rapidly mixed with 0.8 mL of methanol (HPLC grade) to quench further oxidation of benzoate by •OH and then the suspension was filtered through a membrane of 0.22 µM. The concentration of p-HBA was determined by HPLC according to the previous method [28]. The conversion coefficient between p-HBA and cumulative •OH was 5.87 [25,26]. The detection limit of p-HBA was 0.1 µM. For the analysis of Fe(II) dis and Fe(III) dis , another sample of 0.8 mL was filtered through a membrane of 0.22 µM and the filtrate was collected in a pre-acidified vial. Fe(II) dis concentration was measured by the ferrozine method at wavelength 562 nm [29]. To minimize Fe(III)-citrate interference, Fe(II) analysis was performed within 15 min after the chromogenic reaction. Dissolved total iron (Fe total ) was determined by reducing Fe(III) to Fe(II) with hydroxylamine-HCl. The Fe(III) dis was calculated using the difference between dissolved Fe total and Fe(II) dis concentrations. For the analysis of solid Fe(II) and Fe(III), the sample was directly mixed with 1 M HCl to dissolve solid phase components and then analyzed. For the analysis of Fe(III) in colloids (1-220 nm) and true solution (<1 nm), the sample was fractioned by filters of 0.22 µM and ultrafiltration membranes of 20 nm (30 kDa, Millipore) and 1 nm (3 kDa, Pall), respectively. The concentration of phenol was measured by HPLC [10].

Kinetic Modeling and Speciation Calculation
A kinetic model was developed to fit the concentration time series data of Fe(II) dis , Fe(III) dis and •OH under different experimental conditions. Kintecus 6.51 software (James C. Ianni, Lansdowne, PA, USA) was used for calculation [30]. The reaction networks are shown in Table 1 and consist of two subsections: (1) inorganic Fe(II) dis oxidation and (2) extended reactions in the presence of citrate. In the inorganic Fe(II) dis system, both the oxidation of inorganic Fe(II) dis and adsorbed Fe(II) (Fe(II) ad ) were considered (reactions A1-A13). In Fe(II)-citrate system, the complexation of Fe(II) dis and Fe(III) dis by citrate (reactions B1-B4) and the oxidation of citrate complexed Fe(II) (reactions B5-B8) were considered. For the sake of simplification, the interactions among •O 2 − , H 2 O 2 and •OH were not included in the kinetic model. More details are given in Section S1 in the supporting information. Because the solution pH varied less than 0.1 unit during experiments, constant pH was used in the calculations. DO concentration was set at 0.25 mM.  [27] a LEP and LEP i represent the reactive and nonreactive lepidocrocite, respectively. Because the presence of citrate inhibited the hydrolysis and precipitate of inorganic Fe(III) dis , the formation and oxidation of Fe(II) ad (reactions A8-A13) were not included in the Fe(II)-citrate system and the rate constants of Fe(III) hydrolysis and precipitate (reactions A6-A7) were adjusted to <1 × 10 3 , <1 × 10 3 and <1 × 10 4 M −1 s −1 for pH 6, 7 and 7.5, respectively.
To evaluate the influence of citrate/Fe(II) molar ratio on the fraction of complexed Fe(II)/Fe(III), a speciation calculation for Fe(II) and Fe(III) under different experimental conditions was performed with Visual MINTEQ 3.1 [39].

Effect of Citrate/Fe(II) Molar Ratio on •OH Production during Fe(II)-Catalyzed O 2 Oxidation Process
For oxygenation of 250 µM inorganic Fe(II) dis in the absence of citrate, the concentrations of cumulative •OH were always below the detection limit at pH 6 and gradually increased to 1.3 and 0.7 µM at pH 7 and 7.5, respectively (Figure 1a-c). When citrate was added to the above inorganic Fe(II) dis system, •OH accumulation rapidly elevated (Figure 1a-c). For instance, for oxygenation of 250 µM inorganic Fe(II) dis in the presence of 250 µM citrate, •OH accumulation reached 28.5 (>47.5-fold), 13.3 (~10.2-fold) and 8.1 (~11.6-fold) µM for pH 6, 7 and 7.5, respectively (Figure 1), which were much higher than those in the inorganic Fe(II) dis system. The enhancement of citrate on •OH production was in agreement with previous observations [16,18,19,21], which further supported the conclusion that the addition of ligands can effectively reinforce •OH production from Fe(II) oxidation by O 2 . As shown in Figure 1d, the enhancement of citrate on •OH production was highly dependent on citrate/Fe(II) molar ratio and solution pH. At pH 6, the cumulative •OH increased from 2.8 to 8.5 μM (~3.0-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 8.5 to 28.5 μM (~3.3-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 42.3 μM (~1.5-fold) (Figure 1d). At pH 7, the cumulative •OH increased from 2.0 to 4.9 μM (~2.5-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 4.9 to 13.3 μM (~2.7-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 24.2 μM (~1.8-fold) ( Figure  1d). At pH 7.5, the cumulative •OH increased from 2.2 to 3.4 μM (~1.5-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 3.4 to 8.1 μM (~2.4-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 18.0 μM (~2.2-fold) (Figure 1d). The increased folds on •OH accumulation suggests that a moderate citrate/Fe(II) molar ratio can result in a more significant increase in •OH production. As shown in Figure 1d, the enhancement of citrate on •OH production was highly dependent on citrate/Fe(II) molar ratio and solution pH. At pH 6, the cumulative •OH increased from 2.8 to 8.5 µM (~3.0-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 8.5 to 28.5 µM (~3.3-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 42.3 µM (~1.5-fold) (Figure 1d). At pH 7, the cumulative •OH increased from 2.0 to 4.9 µM (~2.5-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 4.9 to 13.3 µM (~2.7-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 24.2 µM (~1.8-fold) (Figure 1d). At pH 7.5, the cumulative •OH increased from 2.2 to 3.4 µM (~1.5-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 ( Figure 1d) and increased from 3.4 to 8.1 µM (~2.4-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 (Figure 1d). When the citrate/Fe(II) molar ratio further increased to 2, the cumulative •OH increased to 18.0 µM (~2.2-fold) (Figure 1d). The increased folds on •OH accumulation suggests that a moderate citrate/Fe(II) molar ratio can result in a more significant increase in •OH production.

Effect of Citrate/Fe(II) Molar Ratio on •OH Yield during Fe(II)-Catalyzed H 2 O 2 Oxidation Process
Similar to the Fe(II)-catalyzed O 2 oxidation process, the presence of citrate also facilitated •OH production during the Fe(II)-catalyzed H 2 O 2 oxidation process (Figure 2a-c). For instance, for the oxidation of 250 µM Fe(II) by 100 µM H 2 O 2 at pH 7, the •OH accumulation increased from 1.5 to 28.7 µM (~19.1-fold) when the citrate concentration increased from 0 to 500 µM (Figure 2b). Because •OH accumulation increased linearly with increasing H 2 O 2 concentration at a given solution pH and an initial Fe(II) dis dosage, the yield of •OH relative to H 2 O 2 decomposition can be derived from the slope of the linear fitting. Figure 2d shows that the •OH yield depended on citrate/Fe(II) molar ratio and solution pH and this dependence can also be divided into three subsections. At pH 6, the •OH yield increased from 6.3% to 7.6% (~1.2-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 7.6% to 26.0% (~3.4-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When the citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 52.2% (~2-fold) ( Table 2). At pH 7, the •OH yield increased from 2.9% to 4.5% (~1.6-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 4.5% to 12.8% (~2.8-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When the citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 31.5% (~2.5-fold) ( Table 2). At pH 7.5, the •OH yield increased from 2.9% to 3.7% (~1.3-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 3.7% to 9.1% (~2.5-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 17.6% (~1.9-fold) (

Effect of Citrate/Fe(II) Molar Ratio on •OH Yield during Fe(II)-Catalyzed H2O2 Oxidation Process
Similar to the Fe(II)-catalyzed O2 oxidation process, the presence of citrate also facilitated •OH production during the Fe(II)-catalyzed H2O2 oxidation process (Figure 2ac). For instance, for the oxidation of 250 μM Fe(II) by 100 μM H2O2 at pH 7, the •OH accumulation increased from 1.5 to 28.7 μM (~19.1-fold) when the citrate concentration increased from 0 to 500 μM (Figure 2b). Because •OH accumulation increased linearly with increasing H2O2 concentration at a given solution pH and an initial Fe(II)dis dosage, the yield of •OH relative to H2O2 decomposition can be derived from the slope of the linear fitting. Figure 2d shows that the •OH yield depended on citrate/Fe(II) molar ratio and solution pH and this dependence can also be divided into three subsections. At pH 6, the •OH yield increased from 6.3% to 7.6% (~1.2-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 7.6% to 26.0% (~3.4-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When the citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 52.2% (~2-fold) ( Table 2). At pH 7, the •OH yield increased from 2.9% to 4.5% (~1.6-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 4.5% to 12.8% (~2.8-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When the citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 31.5% (~2.5-fold) ( Table 2). At pH 7.5, the •OH yield increased from 2.9% to 3.7% (~1.3-fold) with increasing citrate/Fe(II) molar ratio from 0.25 to 0.5 and increased from 3.7% to 9.1% (~2.5-fold) with increasing citrate/Fe(II) molar ratio from 0.5 to 1 ( Table 2). When citrate/Fe(II) molar ratio further increased to 2, the •OH yield increased to 17.6% (~1.9-fold) ( Table 2). These results indicate that a moderate citrate/Fe(II) molar ratio was more beneficial to the increase in •OH yield from H2O2 decomposition.  Previous studies have reported that •OH yield from H 2 O 2 decomposition by inorganic Fe(II) dis at pH 7 was 1.5%-1.6% [18,40], close to our measured value of 1.8% (Table 2). In the presence of citrate, a previous study reported that the •OH yield from H 2 O 2 decomposition by Fe(II) dis at pH 7 was 10% when the molar ratio of citrate/Fe(II) was 1 [18], which was also roughly consistent with the result of this study (12.8%, Table 2). At fixed Fe(II) and citrate concentrations, •OH yield decreased with increasing the solution pH from 6 to 7.5 ( Table 2), which was in line with the previous observation that acidic pH conditions favored •OH production but alkaline pH was unfavorable [12]. Therefore, under similar conditions, our measurements are comparable with previous studies.

Variation of Fe(II)/Fe(III) Species at Different Citrate/Fe(II) Ratios during Oxidation Process
Since Fe(II) is the main electron source for •OH production in Fe(II)-citrate systems [18], the variations of Fe(II) dis and Fe(III) dis during oxygenation were measured. In the absence of citrate, the inorganic Fe(II) dis concentrations within 20-60 min varied by <5%, 98% and 99% at pH 6, 7 and 7.5, respectively ( Figure S1). Inorganic Fe(III) dis was not measured, but abundant Fe(III) precipitates (>0.22 µM) were generated ( Figure S2). XRD analysis shows that lepidocrocite was the main mineral phase of Fe(III) precipitates ( Figure S3). However, the addition of citrate remarkably changed the processes of Fe(II) dis oxidation and Fe(III) dis precipitate (Figure 3). At pH 6, the presence of citrate significantly accelerated Fe(II) oxidation and the oxidation rate increased with increasing citrate/Fe(II) molar ratio (Figure 3a). At pH 7, the presence of citrate accelerated Fe(II) dis oxidation only at the initial stage, i.e., there was no lag of Fe(II) oxidation within the initial 10 min, while it inhibited Fe(II) dis oxidation at the last stage (Figure 3b). At pH 7.5, the addition of citrate inhibited Fe(II) dis oxidation (Figure 3c). At pH 7 and 7.5, the inhibition of citrate on Fe(II) oxidation decreased with an increasing citrate/Fe(II) molar ratio. The influence of citrate on Fe(II) oxidation was related to the formation and oxidation of complexed Fe(II)/Fe(III) species (for details, see Section S3). In addition to Fe(II) dis oxidation, the presence of citrate also had a great influence on the hydrolysis and precipitate of Fe(III) dis . At pH 6-7.5, no Fe(III) precipitate (<1 µM) was detected in Fe(II) dis -citrate system (Figure 3d-f), which was opposite to the observation in the inorganic Fe(II) dis system ( Figure S1). Results of Figure  S3 show that Fe(III) dis was mainly (>90%) in colloidal form (1-220 nm), while the fraction of true Fe(III) dis (<1 nm) was less than 10%. Because Fe(II) oxidation by H 2 O 2 is rapid and not easily sampled, the kinetics of Fe(II) oxidation and Fe(III) dis precipitate during the Fe(II)-catalyzed H 2 O 2 oxidation process were not experimentally measured in this study.
also had a great influence on the hydrolysis and precipitate of Fe(III)dis. At pH 6-7.5, n Fe(III) precipitate (<1 μM) was detected in Fe(II)dis-citrate system (Figure 3d-f), which wa opposite to the observation in the inorganic Fe(II)dis system ( Figure S1). Results of Figur  S3 show that Fe(III)dis was mainly (>90%) in colloidal form (1-220 nm), while the fractio of true Fe(III)dis (<1 nm) was less than 10%. Because Fe(II) oxidation by H2O2 is rapid an not easily sampled, the kinetics of Fe(II) oxidation and Fe(III)dis precipitate during th Fe(II)-catalyzed H2O2 oxidation process were not experimentally measured in this study

Controlling Mechanisms of Citrate/Fe(II) Molar Ratio on •OH Production
Based on the above mentioned, a kinetic model was developed to describe •OH production and Fe(II)/Fe(III) transformation during Fe(II)-catalyzed O 2 and H 2 O 2 oxidation processes ( Table 1). As shown in Figure 1, Figure 3 and Figure S1, the model-predicted time trajectories of Fe(II) dis , Fe(III) dis and •OH were in general agreement with the observed trends. Hence, the reactions in Table 1 can be used to describe the most important reactions in inorganic Fe(II) dis and Fe(II)-citrate systems. Besides, the assumptions made in this study are reasonable and their influence on modeling results could be ignored.
To assess the relative importance of each reaction on •OH production during Fe(II)catalyzed O 2 and H 2 O 2 oxidation processes, the matrices of normalized sensitivity coefficients (NSCs) at different reaction times in inorganic Fe(II) dis and Fe(II)-citrate systems were calculated (Figure 4). The positive NSC values mean that reactions produce •OH, whereas the negative NSC values mean that reactions consume •OH. For the oxygenation of Fe(II) dis by O 2 , in the absence of citrate, reactions A1 and A10 yielded the largest positive NSC values (Figure 4a), which confirmed the contribution of the oxidation of inorganic Fe(II) dis and Fe(II) ad to •OH production. However, in the presence of citrate, the decomposition of H 2 O 2 by citrate complexed Fe(II) (reaction C7) changed, becoming the most important reaction on •OH production given the largest positive NSC value (Figure 4b). In comparison, the reaction of H 2 O 2 with an inorganic Fe(II) dis (reaction A3) generated the negative NSC value (Figure 4b). In other words, reaction A3 was a consumer of •OH. This may be unexpected given that reaction A3 can generate •OH. The explanation is that when H 2 O 2 is decomposed by inorganic Fe(II) dis , less H 2 O 2 can react with citrate complexed Fe(II), while the latter can produce more •OH (Table 1). In addition, the oxidation of Fe(II)-citrate complex (reaction C5) yielded a negative NSC value (Figure 4b), which may be explained by the fact that when the Fe(II)-citrate complex was oxidized by O 2 , less Fe(II)-citrate complex can react with H 2 O 2 to generate •OH. Hence, Fe(II)-citrate complex is the main electron contributor for •OH production in the presence of citrate. For the oxidation of Fe(II) dis by H 2 O 2 , the reactions C1 and C7 also generated the largest positive NSC values (Figure 4d), indicating that the oxidation of Fe(II)-citrate complex by H 2 O 2 mainly contributed to •OH production in the presence of citrate.  To obtain further insight into the influence of citrate/Fe(II) molar ratio on Fe(II) species, the speciation calculation and kinetic models were executed at pH 6-7.5. Before oxidation, the fractions of Fe(II)-citratein total Fe(II) were 24.2%-49.6%, 48.3%-94.2% and 88.8%-99.6% at low (0.25-0.5), moderate (0.5-1) and high (1-2) citrate/Fe(II) molar ratios, To obtain further insight into the influence of citrate/Fe(II) molar ratio on Fe(II) species, the speciation calculation and kinetic models were executed at pH 6-7.5. Before oxidation, the fractions of Fe(II)-citrate − in total Fe(II) were 24.2-49.6%, 48.3-94.2% and 88.8-99.6% at low (0.25-0.5), moderate (0.5-1) and high (1-2) citrate/Fe(II) molar ratios, respectively ( Figure S4). During the oxidation process, the citrate complexed Fe(II) accounted for 18.7-44.5%, 37.0-77.2% and 63.6-93.1% of total Fe of oxygenation at low (0.25-0.5), moderate (0.5-1) and high (1-2) citrate/Fe(II) molar ratios (Figure 5g-i), respectively. Accordingly, the fractions of inorganic Fe 2+ and adsorbed Fe(II) to total Fe of oxygenation decreased in the presence of citrate (Figure 5a-f). The increase of the fractions of Fe(II)-citrate complex with increasing citrate/Fe(II) molar ratio is in line with the observation that the high citrate/Fe(II) molar ratio was beneficial to •OH production (Figures 1 and 2). In summary, the influence of citrate/Fe(II) molar ratio on •OH production during Fe(II)-catalyzed O2 and H2O2 oxidation processes can be ascribed to the change of Fe(II)/Fe(III) speciation. In the absence of citrate, inorganic Fe(II)dis and adsorbed Fe(II) contributed to •OH production. In the presence of citrate, the adsorbed Fe(II) became negligible because Fe(III) precipitates were hindered. Therefore, inorganic Fe(II)dis and Fe(II)-citrate complex contributed collectively to •OH production. At a low citrate/Fe(II) molar ratio (<0.5), inorganic Fe(II)dis mainly contributed to •OH production, followed by Fe(II)-citrate complex. At a high citrate/Fe(II) molar ratio (1-2), Fe(II)-citrate complex mainly contributed to •OH production. As the •OH yield from H2O2 decomposition by Fe(II)-citrate complex is much higher than that by inorganic Fe(II)dis (Table 2), the net •OH production increased with increasing citrate/Fe(II) molar ratio during Fe(II)-catalyzed O2 and H2O2 oxidation processes. In summary, the influence of citrate/Fe(II) molar ratio on •OH production during Fe(II)-catalyzed O 2 and H 2 O 2 oxidation processes can be ascribed to the change of Fe(II)/Fe(III) speciation. In the absence of citrate, inorganic Fe(II) dis and adsorbed Fe(II) contributed to •OH production. In the presence of citrate, the adsorbed Fe(II) became negligible because Fe(III) precipitates were hindered. Therefore, inorganic Fe(II) dis and Fe(II)-citrate complex contributed collectively to •OH production. At a low citrate/Fe(II) molar ratio (<0.5), inorganic Fe(II) dis mainly contributed to •OH production, followed by Fe(II)-citrate complex. At a high citrate/Fe(II) molar ratio (1-2), Fe(II)-citrate complex mainly contributed to •OH production. As the •OH yield from H 2 O 2 decomposition by Fe(II)-citrate complex is much higher than that by inorganic Fe(II) dis (Table 2), the net •OH production increased with increasing citrate/Fe(II) molar ratio during Fe(II)-catalyzed O 2 and H 2 O 2 oxidation processes.

Effect of Citrate/Fe(II) Molar Ratio on Phenol Degradation during Fe(II)-Catalyzed O 2 Oxidation Process
The oxidative impact of •OH produced in a Fe(II)-citrate system toward environmental pollutants was evaluated using phenol as a model pollutant. In a Fe(II)-citrate (1:1) system, phenol concentration decreased 53.6% within 40 min (Figure 6a). When 100 mM 2propanol (k 2-propanol, •OH = 2 × 10 9 M −1 s −1 [27]) was added into the above system, phenol degradation was almost completely inhibited ( Figure 6a). As 2-propanol was the scavenger for •OH, the inhibition confirmed that •OH was the main oxidant for phenol degradation. To verify the applicability of the kinetic model for predicting pollutant degradation, phenol instead of benzoate (reaction B1) was added. Results showed that the model-predicted time trajectories of phenol were in accordance with the experimental observations (Figure 6a), which confirmed the applicability of the kinetic model. Based on the kinetic model, we further assessed the influence of the citrate/Fe(II) molar ratio on phenol degradation in a Fe(II)-citrate system at pH 7. Figure 6b shows that the phenol degradation efficiency rapidly increased from 1.1% to 80.1% when the citrate/Fe(II) molar ratio increased from 0 to 1.8, while it decreased gradually to 46.2% when the citrate/Fe(II) molar ratio reached 8. The dependence between phenol degradation efficiency and citrate/Fe(II) molar ratio may be explained by the fact that citrate can effectively facilitate •OH production from inorganic Fe(II)dis oxidation (Figure 1) but also competed with Based on the kinetic model, we further assessed the influence of the citrate/Fe(II) molar ratio on phenol degradation in a Fe(II)-citrate system at pH 7. Figure 6b shows that the phenol degradation efficiency rapidly increased from 1.1% to 80.1% when the citrate/Fe(II) molar ratio increased from 0 to 1.8, while it decreased gradually to 46.2% when the citrate/Fe(II) molar ratio reached 8. The dependence between phenol degradation efficiency and citrate/Fe(II) molar ratio may be explained by the fact that citrate can effectively facilitate •OH production from inorganic Fe(II) dis oxidation ( Figure 1) but also competed with phenol to consume •OH. A moderate molar ratio of citrate to Fe(II) was more favorable for phenol degradation during the Fe(II)-catalyzed O 2 oxidation process.

Conclusions
This study investigated the influence of citrate/Fe(II) molar ratio on •OH production and the related environmental impacts during Fe(II)-catalyzed O 2 and H 2 O 2 oxidation processes. Results highlighted that the citrate/Fe(II) molar ratio controlled •OH production. In the absence of citrate, •OH is mainly produced from the oxidation of inorganic Fe(II) dis and Fe(II) ad by O 2 and H 2 O 2 . Because the •OH yield from H 2 O 2 decomposition by inorganic Fe(II) dis and Fe(II) ad was relatively low, •OH production was negligible. In the presence of citrate, the complexation of citrate resulted in the formation of Fe(II)citrate complex, which can effectively decompose H 2 O 2 to produce •OH. Hence, the addition of citrate significantly enhanced •OH production during Fe(II)-catalyzed O 2 and H 2 O 2 oxidation processes at pH 6-7.5. The variation of citrate/Fe(II) molar ratio changed Fe(II)/Fe(III) speciation and the fraction of Fe(II)-citrate complex, thereby affecting •OH production. With the increase of citrate/Fe(II) molar ratio, the fraction of Fe(II)-citrate complex increased, so •OH accumulation increased. However, for pollutant removal, a high concentration of citrate can also compete with the pollutant to consume •OH, thus weakening pollutant removal efficiency. Therefore, an appropriate ligand/Fe(II) molar ratio is crucial to achieve ligand-enhanced pollutant removal in the remediation of contaminated soil and groundwater.
Supplementary Materials: The following supporting information can be downloaded at: https:// www.mdpi.com/article/10.3390/ijerph191912977/s1, Section S1: Descriptions of reactions and associated rate constants for kinetic modeling; Section S2 Influence of citrate/Fe(II) molar ratio on •OH production from H 2 O 2 decomposition; Section S3 Influence of citrate on Fe(II) oxidation and Fe(III) dis precipitate; Figure S1. Effects of solution pH on (a) inorganic Fe(II) dis , (b) inorganic Fe(III) dis and (c) solid Fe(III) production during oxidation; Figure S2. XRD patterns of Fe(III) precipitates; Figure S3. Percentage of Fe(III) concentration in different size fractions as a function of solution pH and citrate dosage; Figure S4. (a-c) Fe(II) and (d-f) Fe(III) species speciation distribution as a function of the molar ratio of citrate to Fe(II)/Fe(III). References [41][42][43][44][45]