Biosorption of Cadmium by Non-Toxic Extracellular Polymeric Substances (EPS) Synthesized by Bacteria from Marine Intertidal Biofilms

Cadmium is a major heavy metal found in polluted aquatic environments, mainly derived from industrial production processes. We evaluated the biosorption of solubilized Cd2+ using the extracellular polymeric substances (EPS) produced by Bacillus sp. MC3B-22 and Microbacterium sp. MC3B-10 (Microbactan); these bacteria were originally isolated from intertidal biofilms off the coast of Campeche, Mexico. EPS were incubated with different concentrations of cadmium in ultrapure water. Residual Cd2+ concentrations were determined by Inductive Coupled Plasma-Optic Emission Spectrometry and the maximum sorption capacity (Qmax) was calculated according to the Langmuir model. EPS were characterized by X-ray photoelectron spectroscopy (XPS) before and after sorption. The Qmax of Cd2+ was 97 mg g−1 for Microbactan and 141 mg g−1 for MC3B-22 EPS, these adsorption levels being significantly higher than previously reported for other microbial EPS. In addition, XPS analysis revealed changes in structure of EPS after biosorption and showed that amino functional groups contributed to the binding of Cd2+, unlike other studies that show the carbohydrate fraction is responsible for this activity. This work expands the current view of bacterial species capable of synthesizing EPS with biosorbent potential for cadmium and provides evidence that different chemical moieties, other than carbohydrates, participate in this process.


Introduction
Cadmium (Cd 2+ ) is a transition metal present in the aquatic environment through geochemical processes and, increasingly, through anthropogenic industrial activity; it can accumulate in aquatic life

Bacillus sp. MC3B-22 Identification
Bacillus sp. MC3B-22 was identified by partial sequencing of 16S rRNA gene fragments amplified using the polymerase chain reaction (PCR). Total DNA was obtained with a commercial kit (UltraClean ® Microbial DNA Isolation Kit MO BIO, (QIAGEN INC, Illinois, IL, USA) according to the manufacturer's instructions modified according to [24,25]. In brief, the pure strain was placed in eppendorf tubes with 500 µL of TE buffer pH 8.0, 30 µL of 10% sodium dodecyl sulfate (SDS) and 5 mL of proteinase K (20 mg mL −1 ). They were vortexed and incubated for one hour at 37 • C. After this time, 100 µL of 5 M NaCl and 80 µL of a solution of cetyltrimethyl ammonium bromide in sodium chloride (CTAB/NaCl) added, mixed by inversion and incubated for 10 min at 65 • C. Subsequently phenol: chloroform: isoamyl alcohol (25:24:1) was added, vortexed and centrifuged at 14,000 rpm for 10 min at 24 • C; the supernatant was recovered and transferred to 1.5 mL sterile tubes. A second extraction with an equal volume of chloroform: isoamyl alcohol (24:1) was made by inversion mixing. The tubes were centrifuged at 14,000 rpm for 5 min at 4 • C. The aqueous phase was recovered and DNA precipitation was carried out by adding 0.6 volumes of precooled isopropanol at −20 • C. The tubes were incubated at −20 • C overnight. After incubation, the tubes were centrifuged at 14,000 rpm for 20 min at 4 • C. The resulting DNA was washed with 70% ethanol precooled at −20 • C and centrifuged again; this process was repeated. DNA was allowed to air dry and resuspended in 100 µL of TE pH 8.0 plus 1 µL of RNAse (1 µg µL −1 ). The tubes were incubated in a water bath at 37 • C for 1 h. A second extraction with phenol: chloroform: isoamyl alcohol (25:24:1) was performed to remove RNase following the above-mentioned procedure.
Oligonucleotide primers (forward primer 27f 5 -GAGTTTGATCCTGGCTCA-3 and reverse primer 1385R 5 -CGGTGTGTRCAAGGCCC-3 ) were used to amplify the 16S rRNA gene. The amplification reaction contained 100 ng of DNA, 0.25 µM of each oligonucleotide, 5 µL of 10X PCR buffer, 2 µL of MgSO 4 , 10 mM dNTPs, 1.5 U of Taq polymerase and sterile distilled water to a final volume of 50 µL. The reactions were amplified in a BIO-RAD MJMini ® thermocycler (version 1.1 Ci, Bio-Rad Laboratories, Inc., Hercules, CA, USA). A single PCR cycle consisted of initial denaturation at 95 • C for 2 min and 30 cycles of 95 • C for 60 s, annealing at 55 • C for 60 s, 72 • C for 70 s, and extension at 72 • C for 10 min. The PCR amplicons were purified and DNA was sequenced by MACROGEN, Korea. The sequence was analyzed and edited using the CodonCode Aligner program. The Genbank database was searched using the BLAST program (version 2.2.25, NIH National Institute of Health, Bethesda, MD, USA) at the National Center for Biotechnology Information website (http://www.ncbi.nlm.nih.gov) and sequencing data was analyzed comparing the sequence of nearest relatives found by BLAST searching.

EPS Production
Both EPS were produced by overnight batch shake flask fermentation as previously reported Ortega-Morales et al. [21]. EPS were extracted from the fermented broths as described by Camacho-Chab et al. [22]. The EPS were lyophilized and kept in the dark before experiments. Both EPS have been analyzed and polysaccharides predominate in their composition, with glucose as main neutral sugar; uronic acids (galacturonic acid and glucuronic acid) and hexosamines (N-acetyl glucosamine) are also present and protein content is 38% for Microbactan and 9% for MC3B-22 EPS [21].

Cadmium Biosorption Experiments
50 mg dry EPS were placed in a flask with 50 mL Cd 2+ solution at initial concentrations in the range of 10-100 (10-unit increments) mg L −1 . A stock solution of cadmium (100 mg L −1 ) was prepared by dissolving Cd(COOCH 3 ) 2 (Sigma-Aldrich, St. Louis, MO, USA) in ultrapure water. Flasks were prepared in triplicate and gently shaken (50 rpm) for 24 h at 28 • C and pH 7 [26,27]. After 24 h, solutions were ultrafiltered using Pellicon ® Tangential Flow filtration cassettes (Merk Millipore, Darmstadt, German) [26]. Permeates (residual cadmium concentrations) were acidified with HNO 3 (0.5 N) and cadmium concentration was determined by Inductive Coupled Plasma-Optic Emission Spectrometry (ICP-OES, Perkin Elmer Optima 8300 DV, Wellesley, MA, USA) at a wavelength of 226.502 nm. Retentates were lyophilized prior to further analysis by XPS. Suitable controls were included during biosorption experiments to rule out cadmium adsorption to glass flasks; these were triplicate flasks containing EPS (at varying levels) plus cadmium and flask containing only cadmium.
The amount of cadmium adsorbed, q per unit mass of EPS (mg g −1 ) was determined using the following equation [28]: where Ci is the initial metal concentration and Ceq the equilibrium metal concentration in solution (mg L −1 ) of volume V (mL) and m is the mass of EPS (mg).

Equilibrium Biosorption Isotherm
The Langmuir adsorption isotherm model was employed to describe the Cd 2+ uptake by Microbactan and MC3B-22 EPS [29]. This adsorption isotherm is given by the following equation: where Qmax (mg g −1 ) represents the maximum sorption capacity, K is the Langmuir equilibrium constant (L mg −1 ), and [Me]eq (mg L −1 ) is the equilibrium concentration of the metal in the solution.

X-ray Photoelectron Spectroscopy (XPS)
The composition and oxidation state of surface elements of both EPS were determined by XPS before and after sorption. Analyses were carried with an X-ray photoelectron spectrometer K-Alpha (Thermo Scientific, Waltham, MA, USA) with a hemispheric analyser at 5 × 10 −9 mbar; the sample was excited with monochromatic radiation of Al Kα (1486.68 eV) at 12 kV and 40 W. The general XPS spectra was taken with a pass energy of 100 eV and step size of 1 eV and the individual XPS spectra were taken with a pass energy of 50 eV and step size of 0.1 eV.

Toxicity Test
Artemia sp. (brine shrimp) is an important food for aquaculture, since it can be produced in gnotobiotic conditions and can serve as a vector, transferring probiotics to larvae, thus being a suitable model in the study of how probiotics and pathogenic microorganisms affect [30,31] one of the most important live feeds for commercial production of fish and shellfish [30]. Artemia nauplii have also been used to evaluate the toxicity of contaminants in aquatic environments [31]. The toxicity of the EPS was evaluated by the brine shrimp assay. Brine shrimp eggs (Equinetos Productos ® , TAM, Ciudad de México, Mexico) were hatched in artificial seawater, prepared with 38 g/L of sea salt (Coralife ® , Franklin, WI, USA) added with 6 mg/L of dry yeast, under light and continuous aeration at 27 • C. MC3B-22 EPS and Microbactan, together with standard commercial polymers alginate and xanthan gum (for comparison), were all dissolved separately with seawater at different concentrations (1000, 500, 100, 50 and 10 µg/mL). Copper sulfate pentahydrate was used as a positive control. After incubation of the test for 24 h, dead and live nauplii were counted with the aid of a stereoscope and data were analyzed by the Probit program to determine the lethal concentration of 50% (LC50) of each compound [22].

Molecular Identification of Bacillus sp. MC3B-22
The phylogenetic analysis based on the 16S rDNA sequences indicated strain MC3B-22 to be of the genus Bacillus ( Figure 1). The strain was closely related to Bacillus firmus, with a similarity value of 99% (GeneBank Accesion number HQ116811.1). The EPS produced by B. firmus has previously been reported to remove copper, lead, and zinc from aqueous solutions [32], but this is the first time, to our knowledge, that it has been shown to be effective for Cd sorption.
distances were used to infer the phylogenetic tree and were calculated using the Maximum Composite Likelihood Method [35]. Evolutionary analyses were performed on MEGA7 [36], using Mycobacterium bacteremicum as the outside group.

Cadmium Biosorption Isotherms of Microbactan and B. firmus EPS
The sorption isotherms of cadmium for both EPS are shown in Figure 2. The evolutionary history of the current isolate was inferred using the Neighbor-Joining method [33]. Figure 1 shows the sum of the length of the branch that was 5.236499, as well as the percentage of trees replicated with associated taxa grouped in the test (1000 replicates) [34]. Evolutionary distances were used to infer the phylogenetic tree and were calculated using the Maximum Composite Likelihood Method [35]. Evolutionary analyses were performed on MEGA7 [36], using Mycobacterium bacteremicum as the outside group.

Cadmium Biosorption Isotherms of Microbactan and B. firmus EPS
The sorption isotherms of cadmium for both EPS are shown in Figure 2. distances were used to infer the phylogenetic tree and were calculated using the Maximum Composite Likelihood Method [35]. Evolutionary analyses were performed on MEGA7 [36], using Mycobacterium bacteremicum as the outside group.

Cadmium Biosorption Isotherms of Microbactan and B. firmus EPS
The sorption isotherms of cadmium for both EPS are shown in Figure 2. The simulation of the Langmuir isotherm model showed that both EPS have the ability to sorb to cadmium and that this metal accumulation is a saturated physicochemical process. Table 1 gives the biosorption characteristics of the two types of EPS. The maximum amount of cadmium biosorption on B. firmus EPS (Qmax = 141.1 mg g −1 ) was greater than on Microbactan (Qmax = 97.1 mg g −1 ). Both these figures are considerably greater than most of those reported in the literature for live or dead microbial biomass [12,37]. Ahmed et al. [37] compared the Qmax values for various bacteria, fungi and algae. All were lower than our EPS values, apart from those for the immobilized Bacillus subtilis used by Ahmed et al. [37], which was calculated from a model to be 251.91 mg g −1 , and that for the dead biomass of the endophytic fungus Microsphaeropsis (247.5 mg g −1 ) [38].

XPS Analysis before and after Biosorption
These analyses allowed us to determine the interactions occurring in EPS on Cd sorption.

B. firmus EPS
The XPS C1s spectra for the B. firmus EPS before and after biosorption of cadmium are shown in Figure 3. Before biosorption (Figure 3a), the C1s spectra displays four environments for C atoms, which could correspond to C-H, C-C or C=C, C-O and C=O. The 286.05 eV peak, pertaining to C-O or C-N, was attributed to alcohol, amine or amide. The peak at 287.50 eV, pertaining to C=O or O-C-O, could be attributed to carboxylate or carbonyl, which confirms the presence of polysaccharides in B. firmus EPS. On the other hand, the C1s spectra after biosorption of cadmium (Figure 3b) displayed only three environments for C atoms, which correspond to C-C or C=C, C-O and C=O. A change in the binding energy of these components is observed ( Table 2). The contribution of C-O and C=O decreases after biosorption, while the C-C or C=C contribution remains almost the same. Thus, the change in the C atoms could indicate that the biosorption process is modifying the B. firmus EPS, or that the carbonyl groups are taking part in the metal ion coordination [28,39,40]. XPS analysis has previously shown that the EPS are subject to a change in their chemical structure or conformation during the biosorption process [16]. The simulation of the Langmuir isotherm model showed that both EPS have the ability to sorb to cadmium and that this metal accumulation is a saturated physicochemical process. Table 1 gives the biosorption characteristics of the two types of EPS. The maximum amount of cadmium biosorption on B. firmus EPS (Qmax = 141.1 mg g −1 ) was greater than on Microbactan (Qmax = 97.1 mg g −1 ). Both these figures are considerably greater than most of those reported in the literature for live or dead microbial biomass [12,37]. Ahmed et al. [37] compared the Qmax values for various bacteria, fungi and algae. All were lower than our EPS values, apart from those for the immobilized Bacillus subtilis used by Ahmed et al. [37], which was calculated from a model to be 251.91 mg g −1 , and that for the dead biomass of the endophytic fungus Microsphaeropsis (247.5 mg g −1 ) [38].

XPS Analysis before and after Biosorption
These analyses allowed us to determine the interactions occurring in EPS on Cd sorption.

B. firmus EPS
The XPS C1s spectra for the B. firmus EPS before and after biosorption of cadmium are shown in Figure 3. Before biosorption (Figure 3a), the C1s spectra displays four environments for C atoms, which could correspond to C-H, C-C or C=C, C-O and C=O. The 286.05 eV peak, pertaining to C-O or C-N, was attributed to alcohol, amine or amide. The peak at 287.50 eV, pertaining to C=O or O-C-O, could be attributed to carboxylate or carbonyl, which confirms the presence of polysaccharides in B. firmus EPS. On the other hand, the C1s spectra after biosorption of cadmium (Figure 3b) displayed only three environments for C atoms, which correspond to C-C or C=C, C-O and C=O. A change in the binding energy of these components is observed ( Table 2). The contribution of C-O and C=O decreases after biosorption, while the C-C or C=C contribution remains almost the same. Thus, the change in the C atoms could indicate that the biosorption process is modifying the B. firmus EPS, or that the carbonyl groups are taking part in the metal ion coordination [28,39,40]. XPS analysis has previously shown that the EPS are subject to a change in their chemical structure or conformation during the biosorption process [16].  Figure 4 shows the N1s spectra. The presence of a peak characteristic for nitrogen is seen at 399.78 eV before biosorption (Figure 4a) and this was attributed to NH2 or NH of the proteins. After   Figure 4 shows the N1s spectra. The presence of a peak characteristic for nitrogen is seen at 399.78 eV before biosorption ( Figure 4a) and this was attributed to NH 2 or NH of the proteins. After biosorption, a new peak appeared in the N1s spectrum (Figure 4b) at the higher binding energy of 400.11 eV (Table 2) and this could be assigned to the formation of an -N:-M 2+ complex, a lone pair of electrons in the N atom being donated to cadmium [41]. This complexation between metal ions and the NH 2 or NH has been reported previously in chitosan [41][42][43], but not for microbial EPS. The N1s spectra thus confirm the biosorption of cadmium by B. firmus EPS.  (Table 2) and this could be assigned to the formation of an -N:-M 2+ complex, a lone pair of electrons in the N atom being donated to cadmium [41]. This complexation between metal ions and the NH2 or NH has been reported previously in chitosan [41][42][43], but not for microbial EPS. The N1s spectra thus confirm the biosorption of cadmium by B. firmus EPS.

Microbactan
The C1s XPS spectra for Microbactan before and after biosorption of cadmium are shown in Figure 5. Both C1s XPS spectra (Figure 5a,b) show three C atom environments which were assigned to C-C or C=C, C-O and C=O. However, for three C atoms a change of peak intensity ratios is seen. A possible explanation for this is that Cd 2+ in NH 2 -metal complexes may have a weak interaction with adjacent hydroxyl groups (286.22 eV) (Table 3) because of its relatively larger radius [39]. Alternatively, the decrease in intensity of peak ratio 287.55 eV (Table 3) after the biosorption process could be caused by an ion exchange [42]. The N1s XPS spectrum before biosorption (Figure 6a) shows the characteristic peak for nitrogen at 399.93 eV, attributed to NH 2 or NH (protein fraction). After biosorption, a new peak appears, indicating that metal complexation has occurred with NH 2 or NH. The N1s spectra after cadmium biosorption (Figure 6b), displays a shift in the binding energy; since a higher band corresponds to a more oxidized state, the peak at 399.95 was assigned to the -NH 2 metal complex ( Table 3). The results show that nitrogen-containing groups in both types of EPS play an important role in cadmium biosorption.

Toxicity of Microbactan and B. firmus EPS
The toxicity bioassay showed that neither biopolymer was toxic to A. salina nauplii at concentrations of 1000 μg mL −1 (Table 4). There are no suggestions in the literature that bacterial EPS can be toxic, although this property is rarely measured specifically. These results confirm what is generally assumed by microbiologists and the many uses of EPS in water treatment [20] suggest that this is, indeed, the case. Alginate and xanthan gum were used for comparison, as commercial biopolymers that have been reported to have biosorption abilities. The results show that the new EPS extracts are equally suitable for use in the environment.

Toxicity of Microbactan and B. firmus EPS
The toxicity bioassay showed that neither biopolymer was toxic to A. salina nauplii at concentrations of 1000 µg mL −1 (Table 4). There are no suggestions in the literature that bacterial EPS can be toxic, although this property is rarely measured specifically. These results confirm what is generally assumed by microbiologists and the many uses of EPS in water treatment [20] suggest that this is, indeed, the case. Alginate and xanthan gum were used for comparison, as commercial biopolymers that have been reported to have biosorption abilities. The results show that the new EPS extracts are equally suitable for use in the environment.

Conclusions
This study determined the biosorption capacity of cadmium by the biopolymers Microbactan and MC3B-22, both synthetized by marine bacteria Microbacterium sp. MC3B-10 and Bacillus sp. MC3B-22 (identified by DNA sequencing with 99% similarity to B. firmus). The maximum sorption capacity of Cd 2+ was 97 mg g −1 for Microbactan and 141 mg g −1 for B. firmus EPS, both at pH 7 and 28 • C. XPS analysis revealed changes in structure or conformation of both EPS after biosorption and indicated that NH2 or NH functional groups contributed to binding cadmium. In addition, Microbactan and B. firmus EPS were non-toxic to A. salina nauplii, which is an aquatic model organism widely used in aquaculture activities. Our results showed that B. firmus EPS and Microbactan are very promising for remediation of cadmium in aqueous solutions, with B. firmus perhaps being preferred because of its higher maximum sorption capacity. EPS does not depend for its metal-absorbing activity on microbial metabolic processes and is thus preferable to living biomass. Further studies of these EPS in remediation of heavy metals in water for aqueous systems, including optimization of their production, will be performed in the future.