Correction: Jun, J. A Comprehensive Methodology for Optimizing Read-Out Timing and Reference DAC Offset in High Frame Rate Image Sensing Systems. Sensors 2023, 23, 7048

In the original paper [...].

In the original paper [1], an optimization example was presented in Section 3.7.However, due to the unrealizable condition in Table 1, there were some numerical errors in the results of the example.So, Table 1 has been updated to be more realistic (with 12-bit ADC, 4K, and 23 fps).Based on the updated Table 1, the numbers in Figure 8 and Table 2 have been corrected, and the numbers in the descriptions of the Figure and   A correction has been made to the Section 3.7, Paragraphs 2 and 3, and should read: For example, consider a 7680 × 4320 pixel array (4K) that needs to be digitized with a 12-bit ADC array at 23 fps.The ADC array needs to process the pixel output of 4320 rows 23 times in 1 s, and a one-row read-out time is then 10 µs.With a specific pixel structure, system architecture design, and circuit simulation results, design parameters for a highresolution image sensor can be achieved, as shown in Table 1.With the design parameters, the settling time for ramp offset and the time constant of the amplifier versus ramp offset can be calculated, as shown in Figure 8.A large ramp offset is required to ensure a sufficient ramp offset settling time, which in turn requires a small time constant, which increases power consumption.
Through the iterative calculation based on the other parameters in Table 1 and the equations in Section 3, optimized time budget results can be achieved, as shown in Table 2.With the proposed timing optimization methodology, an optimal reference offset of 360 LSB was achieved.Furthermore, an optimal amplifier time constant of 112.3 ns is also derived, which is equivalent to a bandwidth of 1.42 MHz.Without optimizing the reference offset as proposed in this paper, the power efficiency of an image sensing system becomes very poor.For example, an amplifier bandwidth of 2.12 MHz would be required to maintain the same CL error with an unoptimized reference offset of 240 LSB.
In the Abstract and Section 4, minor text edits have been made to replace some unnecessary details about the previous work, with a reference for clarification.
The corrected part in the Abstract, except for the first five sentences, is as follows: This timing optimization methodology enhances energy efficiency in high-resolution image sensors, enabling higher frame rates and improved system performance.It could be adapted for various imaging applications requiring optimized performance and reduced power consumption, making it a valuable tool for designers aiming to achieve optimal performance in power-sensitive applications.
The corrected first paragraph in Section 4 is as follows: A power-efficient digitizer array for verifying the proposed time budgeting method is implemented in a 28-nanometer process.The prototype digitizer is designed with an optimal reference ramp offset and a 10-bit column-parallel single-slope ADC array.Figure 9 shows an annotated microphotograph of the digitizer chip, which can be stacked with a pixel chip.The comparator array and counter array are operated with a supply voltage of 2.8 V and 1 V, respectively.The peripheral blocks include a DAC for reference ramp signal generation, a voltage doubler for the pixel chip, and reference current generation.
The corrected second paragraph and Table 3 in Section 4 are as follows: The digitizer array chip is connected to a 0.7 µm 108 MP pixel array chip in a 3-D stacked configuration for its performance verification, and the low-frequency noise is suppressed using the digital CDS technique [7]. Figure 10 shows the measured random noise (RN) and column FPN.The sample image captured using the 3-D stacked CIS at  3, the performance of the 108 MP imager is summarized and compared with previously published works [5,11,12,14,16].Compared to other image sensors, this work shows a remarkable FoM with a low RN.
The corrected Figure 9 and Table 3 appear below.The author apologizes for any inconvenience caused and states that the scientific conclusions are unaffected.This correction was approved by the Academic Editor.The original publication has been updated.The author apologizes for any inconvenience caused and states that the scientific conclusions are unaffected.This correction was approved by the Academic Editor.The original publication has been updated.

Figure 8 .
Figure 8.Estimated settling time for ramp offset and the time constant of the amplifier versus ramp offset.
10 fps is shown in Figure 11.An RN of 1.4 e − rms and a column FPN of 66 ppm are measured at an analog gain of 16.The 108 MP imager consumes only 551 mW and also achieves a remarkable figure-of-merit (FoM) of 0.71 e − •nJ based on the common FoM equation for image sensor applications [10].In Table

Table 1 .
Table have also been updated.The corrected Table 1, Figure 8, and Table 2 appear below.Design parameters for timing optimization examples.

Table 2 .
Time budget results of the example.

Table 3 .
Performance summary and comparison.