Wideband SiGe-HBT Low-Noise Amplifier with Resistive Feedback and Shunt Peaking

In this work, the design of a wideband low-noise amplifier (LNA) using a resistive feedback network is proposed for potential multi-band sensing, communication, and radar applications. For achieving wide operational bandwidth and flat in-band characteristics simultaneously, the proposed LNA employs a variety of circuit design techniques, including a voltage–current (shunt–shunt) negative feedback configuration, inductive emitter degeneration, a main branch with an added cascode stage, and the shunt-peaking technique. The use of a feedback network and emitter degeneration provides broadened transfer characteristics for multi-octave coverage and a real impedance for input matching, respectively. In addition, the cascode stage pushes the band-limiting low-frequency pole, due to the Miller capacitance, to a higher frequency. Lastly, the shunt-peaking approach is optimized for the compensation of a gain reduction at higher frequency bands. The wideband LNA proposed in this study is fabricated using a commercial 0.13 μm silicon-germanium (SiGe) BiCMOS process, employing SiGe heterojunction bipolar transistors (HBTs) as the circuit’s core active elements in the main branch. The measurement results show an operational bandwidth of 2.0–29.2 GHz, a noise figure of 4.16 dB (below 26.5 GHz, which was the measurement limit), and a total power consumption of 23.1 mW under a supply voltage of 3.3 V. Regarding the nonlinearity associated with large-signal behavior, the proposed LNA exhibits an input 1-dB compression (IP1dB) point of −5.42 dBm at 12 GHz. These performance numbers confirm the strong viability of the proposed approach in comparison with other state-of-the-art designs.


Introduction
Recent advances in cell phones, WLAN, 5G/6G, and Internet of things (IoT) technologies place ever-increasing demands on the performance of wireless transceivers [1,2]. In addition, as more radio-frequency (RF) communication protocols and require the support of one-chip solutions, higher levels of integration have become mandatory for simpler system configuration and cost-effective implementation [3]. Therefore, RF designers should minimize the use of off-chip components, such as RF chokes and capacitors, and optimize the system performance for wider operational bandwidth in the form of radio-frequency integrated circuits (RFICs). Ideally, component circuit blocks in RF front-ends support flat in-band characteristics, with low fluctuations (or variations) in performance numbers. In

Review of Wideband LNA Core Topology
For designing wideband LNAs, several approaches have been proposed and utilized in the literature. In general, the main topology of wideband LNAs is categorized into the common-base (CB) and the common-emitter (CE) stages [10,11]. Figure 1 shows the core structures of some of the conventional design techniques. First, Figure 1a represents a wideband LNA using a CB stage. The input signal is delivered to the emitter of Q 1 , and the output of the LNA is carried to the collector of Q 1 . At the input side, a passive component (Z E ) is inserted between the emitter and the ground, and its purpose is to block the signal leakage by presenting a large impedance (ideally an AC open). The input signal simultaneously drives the feedforward amplifier, and the amplifier output controls the AC base voltage of the transistor. When a conventional CB structure, without an additional amplifier, is selected for the wideband design, the input matching is relatively straightforward, in contrast to the case of CE [12,13]. Since the effective impedance looking into the emitter terminal of the main transistor is equivalent to 1/g m , this impedance can be optimized to the standard system impedance of 50 Ohm by adjusting the transistor size and the bias [14]. Regarding the gain of a CB LNA, however, due to the tradeoff relation between the signal gain and the noise figure, it is difficult to simultaneously obtain a low noise figure and a high gain. In addition, the fact that from a simple CB stage, the lowest boundary of the achievable noise figure is 3 dB is another weakness. For decoupling both performance parameters against each other, a feedback or feedforward amplifier is often included for optimization, as shown in Figure 1a.

Review of Wideband LNA Core Topology
For designing wideband LNAs, several approaches have been proposed and utilized in the literature. In general, the main topology of wideband LNAs is categorized into the common-base (CB) and the common-emitter (CE) stages [10,11]. Figure 1 shows the core structures of some of the conventional design techniques. First, Figure 1a represents a wideband LNA using a CB stage. The input signal is delivered to the emitter of Q1, and the output of the LNA is carried to the collector of Q1. At the input side, a passive component (ZE) is inserted between the emitter and the ground, and its purpose is to block the signal leakage by presenting a large impedance (ideally an AC open). The input signal simultaneously drives the feedforward amplifier, and the amplifier output controls the AC base voltage of the transistor. When a conventional CB structure, without an additional amplifier, is selected for the wideband design, the input matching is relatively straightforward, in contrast to the case of CE [12,13]. Since the effective impedance looking into the emitter terminal of the main transistor is equivalent to 1/gm, this impedance can be optimized to the standard system impedance of 50 Ohm by adjusting the transistor size and the bias [14]. Regarding the gain of a CB LNA, however, due to the tradeoff relation between the signal gain and the noise figure, it is difficult to simultaneously obtain a low noise figure and a high gain. In addition, the fact that from a simple CB stage, the lowest boundary of the achievable noise figure is 3 dB is another weakness. For decoupling both performance parameters against each other, a feedback or feedforward amplifier is often included for optimization, as shown in Figure 1a. To mitigate the drawbacks of CB-based LNAs and achieve wide operating bandwidth, a CE stage can be utilized for wideband LNA design [15]. Figure 1b,c show examples of CE-based LNAs; the former illustrates an emitter degeneration with a series impedance at the base, and the latter presents a feedback topology between the base and the collector. The primary advantages of this approach include a generally lower noise figure than the CB counterpart, but the impedance matching requires additional circuitry. When the base (or the gate, in a MOSFET) being used is an input terminal, the impedance seen is mostly capacitive in the form of cbe or cgs, respectively [16]. In order to provide a relatively low real impedance to the input side, a degeneration inductor between the emitter and the ground is inserted, as illustrated in Figure 1b. To obtain wideband characteristics, a complex impedance network at the base of the input transistor is often implemented for shaping the target filter response. It is often composed of multiple lumped components To mitigate the drawbacks of CB-based LNAs and achieve wide operating bandwidth, a CE stage can be utilized for wideband LNA design [15]. Figure 1b,c show examples of CE-based LNAs; the former illustrates an emitter degeneration with a series impedance at the base, and the latter presents a feedback topology between the base and the collector. The primary advantages of this approach include a generally lower noise figure than the CB counterpart, but the impedance matching requires additional circuitry. When the base (or the gate, in a MOSFET) being used is an input terminal, the impedance seen is mostly capacitive in the form of c be or c gs , respectively [16]. In order to provide a relatively low real impedance to the input side, a degeneration inductor between the emitter and the ground is inserted, as illustrated in Figure 1b. To obtain wideband characteristics, a complex impedance network at the base of the input transistor is often implemented for shaping the target filter response. It is often composed of multiple lumped components (such as a π network) for low RF ranges [17] or distributed elements for millimeter wave applications. The disadvantage of this approach is large on-chip area due to the passive components. Because the base/emitter impedances are implemented with multiple inductors or capacitors, the overall chip tends to exhibit a higher loss as the operation frequency increases, and the required chip area of inductors or transmission lines can be excessively large [18].
As an alternative, a negative feedback loop is adopted between the input and the output of an LNA [8,17,19,20] (see Figure 1c). Similar to the previous case, the input signal drives the base terminal of Q 1 , whereas the output is at the collector terminal. The main feature of this schematic is that it utilizes a feedback loop where Z F connects two terminals, as shown in Figure 1c. Depending on the type of impedance (real or imaginary) on the feedback path, it is divided into either resistive or reactive feedback, respectively. By analyzing the open-loop and the feedback factor of the circuit, the input impedance can be matched to the source. With the help of the feedback properties, the overall frequency response becomes smoother and wider, and the circuit exhibits improved linearity due to a lower closed-loop gain. In spite of these benefits, the feedback network does not operate well at higher frequencies because of the reduced open-loop gain itself and the effect of parasitics associated with active/passive devices.
Based on the wideband-design techniques above, we have investigated the pros and cons of each approach and combined them, maximizing the benefits of each method. For instance, in order to simultaneously optimize gain and noise performance, a CE-based topology exhibits advantages over a CB stage. In addition, because a well-defined real input impedance is required for matching without degrading other metrics, an emitter degeneration must be included. Next, the goal of wideband transfer characteristics can be achieved with a negative feedback. When the target bandwidth is in multi-octave ranges, the use of a feedback loop only does not provide enough coverage, especially at a higher corner frequency. In this case, design approaches such as shunt-peaking or a cascade stage may be merged into the design. Details of the proposed wideband LNA will be discussed in more detail in the next section.

Design of the Proposed SiGe-HBT LNA
As mentioned in the previous section, a variety of wideband approaches have been utilized. The schematic of the proposed wideband SiGe-HBT LNA is shown in Figure 2. Its core includes a CE stage (Q 1 ) and a CB stage (Q 2 ), in a typical cascode configuration. The CB transistor suppresses the Miller effect by lowering the voltage gain from the base of Q 1 to the emitter of Q 2 . This also enhances the wideband operation of the LNA by pushing the corresponding input pole to a higher frequency [16,20]. Another advantage of a cascode configuration includes the increased output impedance. When a test signal is looking into the collector of Q 2 , the output impedance of an LNA is boosted by a factor of the product of the transconductance and the output resistance of Q 2 . With the increased output impedance, the overall voltage gain increases [17]. As long as the operation frequencies are lower than the unity-gain frequency, the noise contribution from the CB stage is much less dominant in the CE stage.
For generating a resistive impedance at the input interface of the LNA, a degeneration inductor (L E ) is inserted between the emitter of Q 1 and the ground. Along with the series inductor (L B ) at the base of Q 1 , it can present a reasonable input impedance, noise matching, and moderate linearity [16]. With its high quality factor (Q-factor) of L E , this technique has been widely adopted in narrowband LNAs, but it becomes useful in a wideband LNA if a negative feedback is employed around the LNA. Since a negative feedback network broadens the overall Q-factor (de-Qing), the input obtains a real impedance for a wide range of frequencies. As a result, it is possible to achieve impedance matching and optimized NF over those of the target operation bands. In the aspect of implementation, a degeneration inductor is often realized by a custom-designed spiral metal structure or a simple transmission line, due to its small required inductance. After the L E inductance and the feedback impedance have been fixed, the base inductor (L B ) needs to be optimized to support and maintain wideband characteristics. For generating a resistive impedance at the input interface of the LNA, a degeneration inductor (LE) is inserted between the emitter of Q1 and the ground. Along with the series inductor (LB) at the base of Q1, it can present a reasonable input impedance, noise matching, and moderate linearity [16]. With its high quality factor (Q-factor) of LE, this technique has been widely adopted in narrowband LNAs, but it becomes useful in a wideband LNA if a negative feedback is employed around the LNA. Since a negative feedback network broadens the overall Q-factor (de-Qing), the input obtains a real impedance for a wide range of frequencies. As a result, it is possible to achieve impedance matching and optimized NF over those of the target operation bands. In the aspect of implementation, a degeneration inductor is often realized by a custom-designed spiral metal structure or a simple transmission line, due to its small required inductance. After the LE inductance and the feedback impedance have been fixed, the base inductor (LB) needs to be optimized to support and maintain wideband characteristics.
In the proposed wideband LNA, the core stage is configured with a negative feedback loop via a resistor and a capacitor ( Figure 2). The use of feedback resolves the tradeoff relationship between NF and input matching [8]. The selection of a feedback resistance (RF) and a feedback capacitance (CF) should be performed carefully, since it affects the LNA performance when the close-loop is formed. In this design, the feedback operation is mostly determined by RF, whereas the CF provides 1) DC-blocking between the collector of Q2 and the base of Q1 and 2) slight reactance turning for bandwidth optimization. The RF needs to be within a reasonable range such that it maximizes the gain and the bandwidth, but does not overload the open-loop impedances. In addition to the general properties of feedback, it also exhibits the supplementary advantages of improved linearity and the desensitization of parameter variations within the circuit [19,20].
The shunt-peaking technique is adopted to broaden the bandwidth of the gain of the LNA. Conventionally, this approach is employed in analog amplifiers, but it can also be a useful approach in the design of a wideband LNA. By connecting an inductor in series with the resistor in the place of a load, one additional pole and one new zero are introduced into the impedance network [17]. These points collectively create a peak in the magnitude of the transfer function, which allows it to maintain an increased gain over a wider range of frequencies. By optimizing the shunt-peaking network, the gain reduction at the In the proposed wideband LNA, the core stage is configured with a negative feedback loop via a resistor and a capacitor ( Figure 2). The use of feedback resolves the tradeoff relationship between NF and input matching [8]. The selection of a feedback resistance (R F ) and a feedback capacitance (C F ) should be performed carefully, since it affects the LNA performance when the close-loop is formed. In this design, the feedback operation is mostly determined by R F , whereas the C F provides 1) DC-blocking between the collector of Q 2 and the base of Q 1 and 2) slight reactance turning for bandwidth optimization. The R F needs to be within a reasonable range such that it maximizes the gain and the bandwidth, but does not overload the open-loop impedances. In addition to the general properties of feedback, it also exhibits the supplementary advantages of improved linearity and the desensitization of parameter variations within the circuit [19,20].
The shunt-peaking technique is adopted to broaden the bandwidth of the gain of the LNA. Conventionally, this approach is employed in analog amplifiers, but it can also be a useful approach in the design of a wideband LNA. By connecting an inductor in series with the resistor in the place of a load, one additional pole and one new zero are introduced into the impedance network [17]. These points collectively create a peak in the magnitude of the transfer function, which allows it to maintain an increased gain over a wider range of frequencies. By optimizing the shunt-peaking network, the gain reduction at the high-frequency range is compensated, and more flat in-band transfer characteristics can be obtained.

Performance Analysis of the Proposed Wideband LNA
The proposed circuit can be analyzed by deriving the input impedance, the gain, and the noise figure. The simplified small-signal equivalent circuit is shown in Figure 3a. For a SiGe HBT, the Early effect is neglected, and the small-signal model includes only the base-to-emitter capacitor (C BE ) and the transconductance (g m ). The base-to-emitter resistance (r π ) is ignored because its impedance is sufficiently larger than the capacitor impedance 1/sC BE at the operating frequency. In addition, since the cascode device could be regarded as a current buffer, it is omitted in the analysis. the noise figure. The simplified small-signal equivalent circuit is shown in Figure 3a. For a SiGe HBT, the Early effect is neglected, and the small-signal model includes only the base-to-emitter capacitor (CBE) and the transconductance (gm). The base-to-emitter resistance (rπ) is ignored because its impedance is sufficiently larger than the capacitor impedance 1/sCBE at the operating frequency. In addition, since the cascode device could be regarded as a current buffer, it is omitted in the analysis.  The equations derived in this section are obtained from an approximate method based on the shunt-shunt feedback configurations [21]. Only dominant circuit parameters are included in the small-signal circuit, whereas many other parasitics of transistors and inductors were ignored for manageable derivations. Another aspect of the approximate method is that the circuit in Figure 3a is assumed to operate as the standard feedbacksystem model: (1) the input signal flows from vX to vout only through the feedforward path (i.e., from the base to the collector of the input transistor), and (2) the output signal is returned back to vX via the feedback resistor RF only. These assumptions are not always valid when an LNA operates at high frequencies. The neglected parasitics will affect the The equations derived in this section are obtained from an approximate method based on the shunt-shunt feedback configurations [21]. Only dominant circuit parameters are included in the small-signal circuit, whereas many other parasitics of transistors and inductors were ignored for manageable derivations. Another aspect of the approximate method is that the circuit in Figure 3a is assumed to operate as the standard feedbacksystem model: (1) the input signal flows from v X to v out only through the feedforward path (i.e., from the base to the collector of the input transistor), and (2) the output signal is returned back to v X via the feedback resistor R F only. These assumptions are not always valid when an LNA operates at high frequencies. The neglected parasitics will affect the overall response of the LNA, and the reduced open-loop gain limits the bandwidth extension. At low frequencies or center frequency, however, the feedback mechanism operates as it is intended, with the open-loop (transimpedance) gain of equal to or greater than 20-30 dB. Thus, it is possible to apply the feedback theory for analysis. The frequency response obtained from the approximate method may be different from that of the exact analysis due to the use of a feedback system model. On the other hand, if we consider the complexity of the calculation from the exact analysis, the feedback equations provide additional insight into the LNA design and the optimization process, since they present the definitions of important terms in the equations, such as the open-/closed-loop impedances and gain.
After breaking the loop by separating R F into two resistors (Figure 3b), the open-loop parameters can be derived. The open-loop input impedance looking into the base of Q 1 is At v E , by applying KCL, we have the following results; The open-loop impedance with the shunt R F (Z X,open ) is a parallel connection of R F and Z B, as shown below.
Then, the transimpedance gain (R o,open ) can be derived, using the voltage gain from v X to v out . First, we see that the output impedance (Z O ) is a parallel combination of R F and Z L .
By applying KCL at v E , Equation (7) is obtained.
Now, the result of Equation (3) is used in the KCL equation at the node of v out .
By rearranging Equation (8), the voltage gain from v X to v out is, The open-loop transimpedance gain (R o,open ) from the input current (i in,open ) to v out is derived as follows, using Equations (5)  For obtaining the closed-loop input impedance at v in , it is necessary to determine the feedback factor (K f ). The voltage-to-current gain from v out to the node X (K f ) is equivalent to 1/R F , and the corresponding loop gain is, The closed-loop input impedance z X,closed and the overall input impedance z in,closed are shown in Equations (12) and (13), respectively. The input impedance (Z in,closed ) of the LNA is the sum of sL B and Z X,closed , and the parameters must be optimized to deliver 50 ohm to the driving stage.
The voltage gain (A v = V out /V in ) of the proposed LNA can be derived by using the closed-loop equations above. Under the voltage-driven condition, the input current is converted from the input impedance (Z in,closed ), and the closed-loop transimpedance gain is then multiplied to generate the output voltage.
For the optimization of the bandwidth in-band characteristics, the load impedance (Z O ) should be properly designed. To maximize the effect of the shunt-peaking technique, the location of the associated zero is set around the upper corner frequency, whereas the introduced pole appears at a higher frequency than that of the bandwidth.
The simplified small-signal equivalent circuit with noise sources is shown in Figure 4. Among the many noise sources in the LNA, the dominant sources are included in the analysis. The input transistor Q 1 exhibits its shot noise at the emitter-base junction and at the collector-base junction, whereas the feedback resistor and the base inductor present thermal noise. Using the Z in and A v equations above, the NF of an LNA is calculated as shown below.
R , = sL ( sL + sc + g ) Based on the design Equations (1)- (8), the performance of the proposed LNA can be optimized for matching, feedback operation, gain, and noise figure. Due to simplification in the analysis procedure, however, the accurate models and simulations are required for the fine-tuning of the LNA. In addition, parasitics associated with interconnection structures or other distributed elements should be extracted from electromagnetic tools and included in the design, since they may significantly affect the overall circuit behavior, especially at high frequencies.

Simulation and Measurement Results
The proposed wideband LNA was designed using a commercial 0.13 µm SiGe BiC-MOS technology. The optimized final parameters for wideband operation and flat in-band transfer performance are listed in Table 1. The overall design process begins with the size and the bias of the core transistors under the given power budget. With proper transistor dimensions, other matching elements and passives can be optimized for balanced performance. The fabricated chip micrograph of the fabricated LNA circuit is shown in Figure   Figure 4. Simplified small-signal noise-equivalent circuit used for analysis.
In (6), V 2 n,LNA , k, T, R S , and α are the noise contributions of the LNA, the Boltzmann constant, the absolute temperature, the source impedance, and the impedance division between the source and the amplifier, respectively. Under an input-matched condition, the simplified V 2 n,LNA is derived as follows.
where R X,closed is the close-loop transimpedance gain from the node X to the output shown in Figure 3a.
Based on the design Equations (1)- (18), the performance of the proposed LNA can be optimized for matching, feedback operation, gain, and noise figure. Due to simplification in the analysis procedure, however, the accurate models and simulations are required for the fine-tuning of the LNA. In addition, parasitics associated with interconnection structures or other distributed elements should be extracted from electromagnetic tools and included in the design, since they may significantly affect the overall circuit behavior, especially at high frequencies.

Simulation and Measurement Results
The proposed wideband LNA was designed using a commercial 0.13 µm SiGe BiC-MOS technology. The optimized final parameters for wideband operation and flat in-band transfer performance are listed in Table 1. The overall design process begins with the size and the bias of the core transistors under the given power budget. With proper transistor dimensions, other matching elements and passives can be optimized for balanced performance. The fabricated chip micrograph of the fabricated LNA circuit is shown in Figure 5a. The chip size of the core LNA, excluding measurement pads and input/output interconnecting lines, was 0.17 mm 2 (0.36 mm × 0.48 mm). The measurement was conducted using a probe station, a vector network analyzer, a signal source, a spectrum analyzer, and a noise source in an on-chip characterization setup (Figure 5b). The fabricated chip was mounted on the chuck of the probe station, and AC/DC signals were connected via probe tips. Appropriate performance parameters, as well as proper test instruments, equipment, and software tools, were used. Regarding DC operation, the proposed wideband LNA has a current consumption of 7 mA from a 3.3 V supply voltage.
Sensors 2023, 23, x FOR PEER REVIEW 10 of 15 5a. The chip size of the core LNA, excluding measurement pads and input/output interconnecting lines, was 0.17 mm 2 (0.36 mm × 0.48 mm). The measurement was conducted using a probe station, a vector network analyzer, a signal source, a spectrum analyzer, and a noise source in an on-chip characterization setup (Figure 5b). The fabricated chip was mounted on the chuck of the probe station, and AC/DC signals were connected via probe tips. Appropriate performance parameters, as well as proper test instruments, equipment, and software tools, were used. Regarding DC operation, the proposed wideband LNA has a current consumption of 7 mA from a 3.3 V supply voltage.
The small-signal performance parameters are shown in Figure 6. The simulated S 21 scattering parameters (s-parameters) are very close to the measurement results (Figure 6a), showing minimized variations within the operation bandwidth. In Figure 6b, the input reflection coefficient, S 11 , was below −10 dB from 2 to 29 GHz, confirming the viability of the proposed approaches, whereas the output reflection coefficient, S 22 , was not as wide as that of S 11 , requiring the use of a buffer for better matching.  The small-signal performance parameters are shown in Figure 6. The simulated S21 scattering parameters (s-parameters) are very close to the measurement results ( Figure  6a), showing minimized variations within the operation bandwidth. In Figure 6b, the input reflection coefficient, S11, was below −10 dB from 2 to 29 GHz, confirming the viability of the proposed approaches, whereas the output reflection coefficient, S22, was not as wide as that of S11, requiring the use of a buffer for better matching.
(a) (b) Figure 6. Simulated and measured (a) scattering parameters (s-parameters); (b) S11, S22, and S12 (reverse isolation) versus frequency. In Figure 7, the simulated and measured noise characteristics are plotted versus the frequency. The simulation predicted accurate results for low frequencies below 4 GHz, but due to the imperfect noise modeling of the design kits, errors grew as the frequency increases. Because the input matching characteristics were slightly down shifted, it is suspected that the optimum noise is different between the simulation and the hardware. The actual noise measurement was conducted up to 26.5 GHz, due to the limitations of the noise source used in the test. The average NF of the proposed LNA was around 3.7 dB across the operation bandwidth. In Figure 7, the simulated and measured noise characteristics are plotted versus the frequency. The simulation predicted accurate results for low frequencies below 4 GHz, but due to the imperfect noise modeling of the design kits, errors grew as the frequency increases. Because the input matching characteristics were slightly down shifted, it is suspected that the optimum noise is different between the simulation and the hardware. The actual noise measurement was conducted up to 26.5 GHz, due to the limitations of the noise source used in the test. The average NF of the proposed LNA was around 3.7 dB across the operation bandwidth. The large-signal performance of the proposed LNA is presented in Figure 8. The measured 1-dB compression point (IP1dB) was referred to the input side at different operation frequencies. The results showed IP1dB numbers of −8.26, −5.42, and −5.60 dBm at 2, 12, and 24 GHz, respectively. In addition, from the circuit simulation, the input thirdorder point (IIP3) was estimated to be 1.32 dBm at 12 GHz. The large-signal performance of the proposed LNA is presented in Figure 8. The measured 1-dB compression point (IP1dB) was referred to the input side at different operation frequencies. The results showed IP1dB numbers of −8.26, −5.42, and −5.60 dBm at 2, 12, and 24 GHz, respectively. In addition, from the circuit simulation, the input third-order point (IIP3) was estimated to be 1.32 dBm at 12 GHz.  Table 2 summarizes the performance of the proposed wideband SiGe-HBT LNA and compares it with other state-of-the-art LNAs presented in the literature. The proposed LNA achieves a wide operation bandwidth with a low NF, low power consumption, and good linearity among the state-of-the-art designs. Specifically, the proposed LNA exhibits  Table 2 summarizes the performance of the proposed wideband SiGe-HBT LNA and compares it with other state-of-the-art LNAs presented in the literature. The proposed LNA achieves a wide operation bandwidth with a low NF, low power consumption, and good linearity among the state-of-the-art designs. Specifically, the proposed LNA exhibits strength regarding the fractional bandwidth and the noise figure, whereas the power dissipation and linearity are similar to the average performance of other designs. In the last column of Table 2, a sample narrowband LNA is included. In contrast to wideband LNAs, a narrowband LNA has advantages in regards to noise figure and power consumption, as well as linearity. For a better evaluation of the relative performance, figure-of-merit (FoM) equations are used. FoM is a combined function of fractional bandwidth, center frequency, gain, NF, power consumption, etc., and FoM I is defined as follows [22].  The second FoM equation (FoM II ) includes a large-signal parameter (IP1dB) to also address the linearity performance of LNAs [16].
As inferred from the comparison, the proposed LNA exhibits the highest numbers among all the other designs, demonstrating that the concept suggested in this work is effective in designing a high-performance wideband LNA.

Conclusions
The design and the optimization of a wideband SiGe-HBT LNA are presented. The proposed LNA uses multiple approaches for extending the bandwidth of the circuit, such as a resistive feedback network, an emitter-degeneration inductor, a cascode stage, and the shunt-peaking technique. In addition, a detailed analysis of matching, gain, and noise figure is provided, using small-signal models and equivalent circuits. The proposed LNA is implemented in a 0.13 µm SiGe-BiCMOS process, and the measurement shows a wide bandwidth of 2.0-29.2 GHz, simultaneously covering many frequency bands for communi-cation and sensor applications. The overall performance confirms that the proposed LNA is a viable solution for the realization of wideband RF systems.