Interference Level Detector with PCB HDI Rogowski coil for PLC Narrow-Band Applications

This article presents and discusses the structure, principle of operation, and operational properties of a newly developed interference level detector (ILD) designed to measure conducted supraharmonic disturbances (1–150 kHz) in the power grid and to assess the effectiveness of narrow-band Power Line Communication (PLC) transmission, especially in the PRIME technology. The usability assessment was made on the basis of the validation and the results of tests carried out in a low-voltage network with non-linear loads. Appropriate practical conclusions were then formulated.


Introduction
There has been increasing interest recently in using power grids for data transmission, both low-and high-voltage, of a common structure and topology. This is known as Power Line Communication technology (PLC) [1,2]. According to the recommendation of international standards, low-(2-150 kHz) and high-frequency bandwidth  can be used [3]. When it comes to low-voltage networks, a low-frequency bandwidth is most often applied in most European countries, as specified by the European Committee for Electrotechnical Standardization (CENELEC) [4]. The main task of power grids is the transmission and distribution of electrical energy. Therefore, additionally superimposed signals should not have any negative impact on the quality of the transmitted 50/60 Hz electricity. However, electrical phenomena occurring during the grid's operation may significantly interfere with the transmission capacity, particularly transient events. These are mostly due to the operation of non-linear receivers or short circuits and/or switching. It is obvious that the electrical parameters of the power grid are far from those required for effective high-frequency signal transmission. Attenuation, in particular, has the greatest impact, resulting in significant, undesirable, unexpected increasing and decreasing variations of the Signal-to-Noise Ratio (SNR) value with time [5]. Therefore, the effective use of PLC transmission over any electric power network needs online control of the quality of the transmitted signal as well as control of the noise introduced into the communication channel (both induced and conducted). High-frequency perturbations of both current and voltage within the used bandwidth (i.e., from 3 kHz to 150 kHz) are commonly introduced into the power grid, mainly due to the operation of numerous non-linear loads (e.g., modern light sources), commutator motors, and all kinds of pulse rectifiers and frequency converters. It should be noted that most digital modulations of the electrical signal result in interference [6,7]. In practice, the voltage response is usually measured to control the level of interference in transmission channels [8,9]. However, the conducted interferences can be basically rated by analysis of the current detector measurement data. They are of emissions. A 4-channel acquisition system with two Rogowski coil sensors that measure the same current was employed. Although the authors do not provide the construction parameters of the Rogowski coils, their bandwidth suggests that they are either coils with a magnetic core or/and very small geometrical dimensions, which makes it impossible to use them on power cables. In addition, the authors report that the system was validated for frequencies up to 2.5 kHz. A comparison of measurement methods for current and voltage distortions in low-voltage networks in the frequency range from 2 to 150 kHz (SH) is presented in [15]. The comparison encompasses the methods informatively described in the IEC (International Electrotechnical Commission) and CISPR (Comité International Spécial des Perturbations Radioélectriques) international standards, as well as other innovative techniques presented in the literature. All these methods are based on voltage signaling. The possibility of using new amorphous-nanocrystalline alloys with improved temperature stability in a variety of applications is presented in [16]. These alloys give some hope for their effective use as magnetic cores of current sensors for new measuring apparatus for SH emission measurement. However, this requires the development of appropriate meters and their validation under field conditions. A discussion of the main issues of harmonics at the moment and in the near future is presented in [17]. It underlines the impact of harmonics, inter-harmonics, and SH on protection and metering. It states the need for new and improved standards and points out the measurement and data analysis issues. The authors in [18] study the existing power quality disturbances and identify SH emissions as a field of interest. They also present the design and initial tests conducted on a measurement system for SH. The parameters and configurations to be performed during the measurements in the smart grid platform are also discussed. On the basis of the analysis of the current state of knowledge, it can be concluded that there is a lack of appropriate measurement equipment for higher frequencies, especially for SH. Therefore, developing tools for easy and accurate measurement of SH emissions in the power grid are essentially needed. Although the main purpose of this article is to demonstrate the usefulness of the developed ILD for assessing the effectiveness of low-frequency PLC transmission, the authors see the possibility of its wider use, e.g., to study the size of power losses and the heating rate of power transformers, especially dry ones used in mines.

Contributions
The contributions of this article can be summarized as follows.

•
Based on the Rogowski coil, appropriately designed and constructed with PCB HDI technology, the concept of the measuring system intended for e-management of detection and measurement of current harmonics with a frequency range from 2 kHz to 150 kHz was developed. Since the interference level detector is intended for use both in low-power and high-power grids, the geometric dimensions of the Rogowski coil have been carefully chosen so that it is possible to perform measurements in wires (cables) with a diameter of up to 0.05 m, which are the most common in such grids. The construction of the coil, made with PCB technology, was a compromise with respect to the value of the transformation ratio, equal to 1 mV/A (at 50 Hz), and the effective measurement frequency bandwidth, which was extended up to 150 kHz.

•
Validation was performed for a harmonics current of 5 mA within the range of 1 kHz-150 kHz, respectively. The study of the PLC communication in a low-voltage power grid (in PRIME technology) and signal detection efficiency was carried out for randomly distorted currents as well as voltage waveforms due to linear and/or non-linear electrical energy receivers being fed from the grid.
The paper is organized as follows. Section 2 presents the structure and assumed operational parameters of the interference level detector. Section 3 discusses the method and scope of validation together with the results of laboratory tests. Section 4 is devoted to testing the efficiency of the detector system under simulated real working conditions of PLC transmission in the low-voltage network. It presents research results and discussions. Finally, Section 5 concludes the paper.

Construction of the Detector and the Principle of Operation
The key element of the detector is a Rogowski coil. Therefore, its frequency characteristic should be selected and matched properly to ensure the highest possible sensitivity of the measurements for the required dimensions of the so-called transformer internal window [13]. The window should enable the detector to be located properly onto the 1-phase low-voltage conductor/cable of the size used in practice. It should be noted that it is difficult to meet high sensitivity requirements without the use of a special magnetically formed core material. However, as the authors found, this difficulty can be overcome in practical applications by the use of the Rogowski coil made with PCB HDI technology [19]. Moreover, the Rogowski coil made with this technology with evenly distributed secondary winding (printed circuit boards) over the coil periphery displays relatively high immunity to external interfering electromagnetic fields. Additionally, its sensitivity depends very little on the location of the primary conductor inside the internal coil window [20,21]. Therefore, the use of the Rogowski coil (particularly made with PCB HDI technology) as a detector of conducted current perturbations is fully justified. A simplified block diagram and layout view of the developed interference detector is shown in Figures 1 and 2. It consists of three basic blocs, 1-the Rogowski coil (RC) (superimposed on a conductor with a controlled current), 2-the measuring system (MV), and 3-the computer (PC) (with the "PLC acquisition" application installed). USB1 is a port for uploading a binary file with appropriate settings, whereas USB2 is used as a battery charging port.
scope of validation together with the results of laboratory tests. Section 4 is devoted to testing the efficiency of the detector system under simulated real working conditions of PLC transmission in the low-voltage network. It presents research results and discussions. Finally, Section 5 concludes the paper.

Construction of the Detector and the Principle of Operation
The key element of the detector is a Rogowski coil. Therefore, its frequency characteristic should be selected and matched properly to ensure the highest possible sensitivity of the measurements for the required dimensions of the so-called transformer internal window [13]. The window should enable the detector to be located properly onto the 1phase low-voltage conductor/cable of the size used in practice. It should be noted that it is difficult to meet high sensitivity requirements without the use of a special magnetically formed core material. However, as the authors found, this difficulty can be overcome in practical applications by the use of the Rogowski coil made with PCB HDI technology [19]. Moreover, the Rogowski coil made with this technology with evenly distributed secondary winding (printed circuit boards) over the coil periphery displays relatively high immunity to external interfering electromagnetic fields. Additionally, its sensitivity depends very little on the location of the primary conductor inside the internal coil window [20,21]. Therefore, the use of the Rogowski coil (particularly made with PCB HDI technology) as a detector of conducted current perturbations is fully justified. A simplified block diagram and layout view of the developed interference detector is shown in Figures 1 and  2. It consists of three basic blocs, 1-the Rogowski coil (RC) (superimposed on a conductor with a controlled current), 2-the measuring system (MV), and 3-the computer (PC) (with the "PLC acquisition" application installed). USB1 is a port for uploading a binary file with appropriate settings, whereas USB2 is used as a battery charging port.  The measured input signal from the Rogowski coil is fed (in the measuring system) to a high-pass filter (HPF) with a cut-off frequency of 1 kHz. The signal is then sent via a differential amplifier (PGA) with adjustable gain to a 16-bit SAR analog-to-digital converter and further to the W7500 module (containing an ARM microcontroller) via the Ethernet link (ETH) to the computer (PC). The sampling frequency of the SAR converter is equal to 483 kHz, which, in principle, enables measuring signals with frequency content up to 241.5 kHz, but the measurement bandwidth of the developed detector was intentionally limited to 150 kHz, as this was the frequency range of interest. The measuring system (MV) can be powered externally through one of the two ports. However, during measurements, it should be powered only from the internal battery, and no cables should be connected to the USB1 and USB2 ports (neither to the computer nor to an external power source). In this mode of operation, the level of measurement data interference is the lowest. The measured input signal from the Rogowski coil is fed (in the m to a high-pass filter (HPF) with a cut-off frequency of 1 kHz. The signal differential amplifier (PGA) with adjustable gain to a 16-bit SAR anal verter and further to the W7500 module (containing an ARM microc Ethernet link (ETH) to the computer (PC). The sampling frequency of t is equal to 483 kHz, which, in principle, enables measuring signals with f up to 241.5 kHz, but the measurement bandwidth of the developed de tionally limited to 150 kHz, as this was the frequency range of interes system (MV) can be powered externally through one of the two ports. measurements, it should be powered only from the internal battery, and be connected to the USB1 and USB2 ports (neither to the computer n power source). In this mode of operation, the level of measurement da the lowest.

Advantages over Other Solutions
The developed ILD is easy to deploy in real-life operations due to se Rogowski coil sensor is a splittable type (Figure 2), which makes it possi an electric cable without making any disconnections. This feature mak ILD stand out against other devices made for the same purpose. The IL ered by an internal battery during operation, which makes it independe power sources. The connection of the ILD device to the PC computer i cable, which is quite resilient to external interferences.

Method and Scope of Validation
In order to validate the performance of the developed detector, were carried out using the arranged electric system, the sketch of which i 3.

Advantages over Other Solutions
The developed ILD is easy to deploy in real-life operations due to several factors. The Rogowski coil sensor is a splittable type (Figure 2), which makes it possible to install it on an electric cable without making any disconnections. This feature makes the developed ILD stand out against other devices made for the same purpose. The ILD device is powered by an internal battery during operation, which makes it independent of any external power sources. The connection of the ILD device to the PC computer is via an Ethernet cable, which is quite resilient to external interferences.

Method and Scope of Validation
In order to validate the performance of the developed detector, appropriate tests were carried out using the arranged electric system, the sketch of which is shown in Figure 3. The value of the current (0.1-50 mA) in the circuit with adjustable frequency (1-150 kHz provided by the signal generator GWINSTEK AFG 2225) was controlled by monitoring the voltage drop U1 across the 100 Ω class 0.01 resistive shunt. In the first step, the amplitude-frequency response of the Rogowski coil (U2 = f(f)), Figure 4, was measured for  The value of the current (0.1-50 mA) in the circuit with adjustable frequency (1-150 kHz provided by the signal generator GWINSTEK AFG 2225) was controlled by monitoring the voltage drop U 1 across the 100 Ω class 0.01 resistive shunt. In the first step, the amplitudefrequency response of the Rogowski coil (U 2 = f(f )), Figure 4, was measured for the coil disconnected from the MV system. It can be seen that the largest gain is for a frequency slightly higher than 100 kHz. The value of the current (0.1-50 mA) in the circuit with adjustable frequency (1-15 kHz provided by the signal generator GWINSTEK AFG 2225) was controlled by monitor ing the voltage drop U1 across the 100 Ω class 0.01 resistive shunt. In the first step, th amplitude-frequency response of the Rogowski coil (U2 = f(f)), Figure 4, was measured fo the coil disconnected from the MV system. It can be seen that the largest gain is for frequency slightly higher than 100 kHz. The coil's amplitude-frequency characteristic, stored in a text file, is then recalculated after being entered into the detector microprocessor control circuit upon the activation o the "PLC acquisition" application. The recalculation consists in approximating it by spliced polynomials of 3 degrees in the range from 0 Hz to 241.5 kHz. After connecting the Rogowski coil to the MV measurement system, the response of the interference leve detector to the measured input current signals in the range from 0.1mA to 50mA and fre quencies from 1 kHz to 100 kHz was controlled and recorded. The accuracy of the meas uring instruments was around ±0.05%.
The frequency spectrum Y(f) of the Rogowski coil's primary current was determined with the use of Discrete Fourier Transform from the samples of the coil's output voltag according to the equation: The coil's amplitude-frequency characteristic, stored in a text file, is then recalculated after being entered into the detector microprocessor control circuit upon the activation of the "PLC acquisition" application. The recalculation consists in approximating it by spliced polynomials of 3 degrees in the range from 0 Hz to 241.5 kHz. After connecting the Rogowski coil to the MV measurement system, the response of the interference level detector to the measured input current signals in the range from 0.1mA to 50mA and frequencies from 1 kHz to 100 kHz was controlled and recorded. The accuracy of the measuring instruments was around ±0.05%.
The frequency spectrum Y(f ) of the Rogowski coil's primary current was determined with the use of Discrete Fourier Transform from the samples of the coil's output voltage according to the equation: where y(j) is the jth spectral line, x(k) is the k-sample of the coil output voltage, I is the unit imaginary number, and n is the number of samples acquired. The sample acquisition interval was equal to 0.1 s, so the frequency resolution was equal to 10 Hz. The spectrum displayed on the computer screen was the Y(f ) spectrum corrected each time by the inverse amplitude frequency characteristic of the coil, A(f ). The correction consisted in multiplying each spectral line y(j) computed from (1) by the correction coefficient cc(j), The ILD also has the option of turning off the above-described correction of the Y(f ) spectrum. In this mode of operation, it can be used to measure the amplitude-frequency characteristic of the coil.
Additional spectral correction, removing to some extent the spectrum leakage, can be carried out (optionally) by the mean-square operation of summing closely spaced spectral lines. In the corrected spectrum, each such closely spaced group of spectral lines with For the highest gain of the MV system, the measured range is limited to around 30 mV at the output of the Rogowski coil. An output spectral line image for the input current value of 45 mA, at a single frequency equal to 25 kHz is shown as an example in Figure 5 (another spectral line of lower amplitude and frequency around 75 kHz visible in the figure is due to waveform deformation of the supply voltage during the test) (1). characteristic of the coil.
Additional spectral correction, removing to some extent the spectrum leakage, can be carried out (optionally) by the mean-square operation of summing closely spaced spectral lines. In the corrected spectrum, each such closely spaced group of spectral lines with indexes from p to q is substituted by a group of spectral lines of the same cardinality where only one spectral line y(fc), with frequency fc, is different from zero. The frequency fc and the amplitude of y(fc) are computed according to the following equations: For the highest gain of the MV system, the measured range is limited to around 30 mV at the output of the Rogowski coil. An output spectral line image for the input current value of 45 mA, at a single frequency equal to 25 kHz is shown as an example in Figure 5   The output voltage measurement results obtained by the detector show a practically linear correlation between the value of the Rogowski coil output voltage spectral line amplitude and the current amplitude at a given frequency ( Figure 6). The output voltage measurement results obtained by the detector show a practically linear correlation between the value of the Rogowski coil output voltage spectral line amplitude and the current amplitude at a given frequency ( Figure 6). However, the slope of the voltage-current relationship depends on the frequency and is determined by the amplitude-frequency characteristic of the Rogowski coil. The electrical equivalent circuit of the coil is a series resonance circuit made of the coil self-induct- However, the slope of the voltage-current relationship depends on the frequency and is determined by the amplitude-frequency characteristic of the Rogowski coil. The electrical equivalent circuit of the coil is a series resonance circuit made of the coil selfinductance and inter-winding capacitance [19]. Below the resonance frequency of this series resonance circuit, at frequencies up to 50 kHz, the coil's output voltage increases linearly with frequency (at constant current amplitude), which is a demonstration of the Faraday law. At frequencies above 50 kHz, the series resonance circuit starts to modify the coil's output voltage amplitude. The calculated transformation ratio S (Figure 7) shows that a 2-fold increase in the frequency below 50 kHz (e.g., from 20 kHz to 40 kHz) increases the value of the S 2 times, whereas, above 50 kHz (e.g., from 50 kHz to 100 kHz), the S increases 3 times. However, the slope of the voltage-current relationship depends on the frequency and is determined by the amplitude-frequency characteristic of the Rogowski coil. The electrical equivalent circuit of the coil is a series resonance circuit made of the coil self-inductance and inter-winding capacitance [19]. Below the resonance frequency of this series resonance circuit, at frequencies up to 50 kHz, the coil's output voltage increases linearly with frequency (at constant current amplitude), which is a demonstration of the Faraday law. At frequencies above 50 kHz, the series resonance circuit starts to modify the coil's output voltage amplitude. The calculated transformation ratio S (Figure 7) shows that a 2-fold increase in the frequency below 50 kHz (e.g., from 20 kHz to 40 kHz) increases the value of the S 2 times, whereas, above 50 kHz (e.g., from 50 kHz to 100 kHz), the S increases 3 times.  Therefore, the sensitivity (over 0.1 mA) of the measurement increases with the interfering frequency, which is convenient for the effective detection of supraharmonics, particularly at higher frequencies. It should be noted that the spectrum can be displayed in both voltage and current values resulting from the transformation ratio of the Rogowski coil.

Sources of Interference of Narrow-Band PLC Transmission in the Low-Voltage Power Grid
The main threat to effective narrow-band PLC transmission in power grids is the interference generated primarily by any digital (non-linear) electronic device working in the impulse mode and/or the use of switching power supplies. Regardless of the PLC transmission, this interference also significantly deteriorates the power quality indices in the grid. Large interference is introduced by any fluorescent light source (CFL) with electronic ballast. An example of the energy quality deterioration in a low-voltage grid, especially the current, due to a group (7) of compact fluorescent lamps, is shown in Figure 8. terference generated primarily by any digital (non-linear) electronic device working in the impulse mode and/or the use of switching power supplies. Regardless of the PLC transmission, this interference also significantly deteriorates the power quality indices in the grid. Large interference is introduced by any fluorescent light source (CFL) with electronic ballast. An example of the energy quality deterioration in a low-voltage grid, especially the current, due to a group (7) of compact fluorescent lamps, is shown in Figure 8.  Switched-mode power supplies also have a similar impact on the network, shown, for example, for a 1-phase adapter powering a LED light source, Figure 9. It should be noted that in the case of the 3-phase UPS (Uninterruptible Power Supply), particularly for server room use, different distortions of current and voltage waveforms in different phases as well as in the neutral conductor can be found.
Switched-mode power supplies also have a similar impact on the network, shown, for example, for a 1-phase adapter powering a LED light source, Figure 9. It should be noted that in the case of the 3-phase UPS (Uninterruptible Power Supply), particularly for server room use, different distortions of current and voltage waveforms in different phases as well as in the neutral conductor can be found. The operation of all types of commutator electric motors (used, e.g., in home appliances) also creates a threat to the quality of the electricity supply (see Figure 10) and PLC transmission. The operation of all types of commutator electric motors (used, e.g., in home appliances) also creates a threat to the quality of the electricity supply (see Figure 10) and PLC transmission. However, power quality measurement devices are not adapted to measure supraharmonics, and therefore, they are not able to detect high-frequency disturbances. Their frequency range is, in practice, limited to the 40th harmonic.
The conducted research on the identification of 260 sources of interference at enduser loads of narrow-band PLC communication in the Open Smart Grid Protocol (OSGP) band (75 and 86 kHz), based on the voltage response, showed that the main contributions are made by CFL light sources, frequency converters, light emitting diodes (LED) light sources, switching power supplies, base transceiver stations (BTS) power supply systems, and DVB-T decoders. The share of the identified loads can be compared to the share of the so-far unidentified loads, as shown in Figure 11 [7]. However, power quality measurement devices are not adapted to measure supraharmonics, and therefore, they are not able to detect high-frequency disturbances. Their frequency range is, in practice, limited to the 40th harmonic.
The conducted research on the identification of 260 sources of interference at end-user loads of narrow-band PLC communication in the Open Smart Grid Protocol (OSGP) band (75 and 86 kHz), based on the voltage response, showed that the main contributions are made by CFL light sources, frequency converters, light emitting diodes (LED) light sources, switching power supplies, base transceiver stations (BTS) power supply systems, and DVB-T decoders. The share of the identified loads can be compared to the share of the so-far unidentified loads, as shown in Figure 11 [7]. Sensors 2023, 23, x FOR PEER REVIEW 12 of 16 Figure 11. Share of end-user loads in the identified 260 interference sources in OSGP PLC transmission.

Purpose and Scope of Research
The aim of this research was to test the usefulness of the developed interference level detector (ILD) for the quality control of narrow-band PLC transmission in the 3-95 kHz band. The interference introduced by selected (non-linear) low-voltage receivers, which primarily deteriorate the quality of electricity supply, was taken into account. The tests were carried out in the measurement system, the diagram of which is shown in Figure 12. It was performed for different levels of waveform deformation, especially current waveforms, and thus for different levels of conducted disturbances. The impact of interferences on PLC transmission in powerline intelligent metering evolution (PRIME) technology (42-89 kHz) was evaluated as an example.

Purpose and Scope of Research
The aim of this research was to test the usefulness of the developed interference level detector (ILD) for the quality control of narrow-band PLC transmission in the 3-95 kHz band. The interference introduced by selected (non-linear) low-voltage receivers, which primarily deteriorate the quality of electricity supply, was taken into account. The tests were carried out in the measurement system, the diagram of which is shown in Figure 12. It was performed for different levels of waveform deformation, especially current waveforms, and thus for different levels of conducted disturbances. The impact of interferences on PLC transmission in powerline intelligent metering evolution (PRIME) technology (42-89 kHz) was evaluated as an example.

Purpose and Scope of Research
The aim of this research was to test the usefulness of the developed interference level detector (ILD) for the quality control of narrow-band PLC transmission in the 3-95 kHz band. The interference introduced by selected (non-linear) low-voltage receivers, which primarily deteriorate the quality of electricity supply, was taken into account. The tests were carried out in the measurement system, the diagram of which is shown in Figure 12. It was performed for different levels of waveform deformation, especially current waveforms, and thus for different levels of conducted disturbances. The impact of interferences on PLC transmission in powerline intelligent metering evolution (PRIME) technology (42-89 kHz) was evaluated as an example. The conducted tests showed that all selected non-linear receivers are possible sources of interference within the examined frequency range. However, the spectrum of the disturbances may differ from each other. This applies to both the range and their maximum value, compared in Figure 13. For example, the interference generated by fluorescent lamps ranges from about 3 kHz to about 80 kHz. The maximum values of disturbing voltage pulses (from 0.5 mV to about 2.5 mV) appear at frequencies of 20 kHz, 40 kHz, 55 kHz, and about 70 kHz, respectively (see Figure 13a). Taking into account the amplitude-frequency characteristics of the Rogowski coil being used, it can be appropriately converted into current value if needed.
Sensors 2023, 23, x FOR PEER REVIEW 13 of 16 Figure 12. Schematic diagram of the measuring electric system for testing the efficiency of the developed interference level detector (ILD); (a)-measurement of interferences due to particular receivers, (b)-interference in PLC PRIME transmission technology.
The conducted tests showed that all selected non-linear receivers are possible sources of interference within the examined frequency range. However, the spectrum of the disturbances may differ from each other. This applies to both the range and their maximum value, compared in Figure 13. For example, the interference generated by fluorescent lamps ranges from about 3 kHz to about 80 kHz. The maximum values of disturbing voltage pulses (from 0.5 mV to about 2.5 mV) appear at frequencies of 20 kHz, 40 kHz, 55 kHz, and about 70 kHz, respectively (see Figure 13a). Taking into account the amplitude-frequency characteristics of the Rogowski coil being used, it can be appropriately converted into current value if needed.  On the other hand, the interference generated by the single-phase LED impulse adapter covers the entire tested frequency range from about 3 kHz to 100 kHz, but its maximum values (about 2 mV) occur regularly at 40 kHz and at about 83 kHz, respectively (see Figure 13b). The spectrum due to the hair dryer, equipped with a commutator motor, is characterized by an average pulse at a frequency of about 68 kHz and a value of up to about 0.4 mV, but with a much larger spectral width of around 10 kHz. The short impulse with a frequency of around 20 kHz visible in Figure 13c does not result from the operation of the dryer but most likely is due to disturbance introduced from the external power grid (city side), which is not galvanically isolated from the one in the lab. It should be noted that such impulses happened randomly during the entire testing period. Having completed the research on the nature and amount of interference due to selected receivers, the usefulness of the ILD detector for quality control and immunity to the interference of PLC transmission in the PRIME technology was checked. It was carried out in the measurement system shown in Figure 12b.
An example of data spectra in PRIME technology in an electric circuit without any interference introduced by the operation of non-linear receivers is presented in Figure 14a. The visible voltage peak with a frequency of about 20 kHz is a parasitic interference introduced from a non-galvanically isolated city network, most likely due to electric wheeled transportation. In the case of the operation of non-linear receivers, the PLC transmission in the PRIME technology may be deteriorated. This can be seen from the comparison of the measured data spectra shown in Figure 14a,b, respectively.
On the other hand, the interference generated by the single-phase LED impulse adapter covers the entire tested frequency range from about 3 kHz to 100 kHz, but its maximum values (about 2 mV) occur regularly at 40 kHz and at about 83 kHz, respectively (see Figure 13b). The spectrum due to the hair dryer, equipped with a commutator motor, is characterized by an average pulse at a frequency of about 68 kHz and a value of up to about 0.4 mV, but with a much larger spectral width of around 10 kHz. The short impulse with a frequency of around 20 kHz visible in Figure 13c does not result from the operation of the dryer but most likely is due to disturbance introduced from the external power grid (city side), which is not galvanically isolated from the one in the lab. It should be noted that such impulses happened randomly during the entire testing period. Having completed the research on the nature and amount of interference due to selected receivers, the usefulness of the ILD detector for quality control and immunity to the interference of PLC transmission in the PRIME technology was checked. It was carried out in the measurement system shown in Figure 12b.
An example of data spectra in PRIME technology in an electric circuit without any interference introduced by the operation of non-linear receivers is presented in Figure 14a. The visible voltage peak with a frequency of about 20 kHz is a parasitic interference introduced from a non-galvanically isolated city network, most likely due to electric wheeled transportation. In the case of the operation of non-linear receivers, the PLC transmission in the PRIME technology may be deteriorated. This can be seen from the comparison of the measured data spectra shown in Fig. 14a and 14b, respectively. As research has shown, PLC transmission in the PRIME technology can deteriorate under the operation of non-linear receivers. The nature of the spectrum deterioration depends on the type of the load, and particularly, fluorescent lamps (CFL) have indicated a significant influence among the tested receivers. The developed interference detector fully confirmed its usefulness for measuring the conducted disturbances in the 3-100 kHz band caused by the operation of non-linear receivers and, thus, for controlling the deterioration of narrow-band PLC transmission, including the PRIME technology.

Conclusions
The article presents and discusses the structure and operational parameters of the newly developed interference detector (ILD) with a specially selected Rogowski coil made Figure 14. The spectrum of the signal transmitted in the PRIME technology in a circuit without interference (a) and under interference due to the operation of non-linear receivers (a set of 7 fluorescent lamps plus an adapter of a LED light source)-(b).
As research has shown, PLC transmission in the PRIME technology can deteriorate under the operation of non-linear receivers. The nature of the spectrum deterioration depends on the type of the load, and particularly, fluorescent lamps (CFL) have indicated a significant influence among the tested receivers. The developed interference detector fully confirmed its usefulness for measuring the conducted disturbances in the 3-100 kHz band caused by the operation of non-linear receivers and, thus, for controlling the deterioration of narrow-band PLC transmission, including the PRIME technology.

Conclusions
The article presents and discusses the structure and operational parameters of the newly developed interference detector (ILD) with a specially selected Rogowski coil made with high-density printed circuit board technology (PCB HDI). This device is designed for the e-management of detection and measurement of conducted interferences (mainly related to distortion of current waveforms) that deteriorate narrow-band PLC transmission in the frequency range of 2-150 kHz. Interference in this frequency band (called supraharmonics) is mainly caused by any digital (non-linear) electronic device working in impulse mode and/or by using a switching power supply. The conducted research has shown that the majority of non-linear receivers that deteriorate the quality of electricity transmitted in the network are also a source of SH. Taking into account the fact that the developed ILD is intended for use both in low-and medium-voltage electrical networks, the parameters and dimensions of the Rogowski coil have been appropriately adapted so that the coil could be applied to electrical wires with a diameter of up to 0.05 m while ensuring a transformation ratio of not less than 1 mV/A (for 50 Hz). The validation carried out for current signals with values from 0.1 to 50 mA showed that the developed detector correctly detects and records the values and changes of current signals in the frequency range from 1 to 100 kHz. The sensitivity of the measurements was found to increase (for currents over 0.1 mA) with the interfering frequency, which is beneficial for SH detection. For user convenience, the spectrum can be displayed on a PC screen in both voltage and current values after taking into account the transformation ratio of the Rogowski coil. The conducted research confirmed the deterioration of PLC transmission in the PRIME technology by quite commonly used non-linear receivers. Fluorescent lamps (CFLs) play a significant role here. Therefore, the usefulness of the developed ILD for control of the disturbances due to SH as well as for control of the efficiency of narrow-band PLC transmission, including PRIME technology, has been demonstrated and proved.