Design and Fabrication of a Novel Wheel-Ring Triaxial Gyroscope

This paper presents a new type of three-axis gyroscope. The gyroscope comprises two independent parts, which are nested to further reduce the structure volume. The capacitive drive was adopted. The motion equation, capacitance design, and spring design of a three-axis gyroscope were introduced, and the corresponding formulas were derived. Furthermore, the X/Y driving frequency of the gyroscope was 5954.8 Hz, the Y-axis detection frequency was 5774.5 Hz, and the X-axis detection frequency was 6030.5 Hz, as determined by the finite element simulation method. The Z-axis driving frequency was 10,728 Hz, and the Z-axis sensing frequency was 10,725 Hz. The MEMS gyroscope’s Z-axis driving mode and the sensing mode’s frequency were slightly mismatched, so the gyroscope demonstrated a larger bandwidth and higher Z-axis mechanical sensitivity. In addition, the structure also has good Z-axis impact resistance. The transient impact simulation of the gyroscope structure showed that the maximum stress of the sensitive structure under the impact of 10,000 g@5 ms was 300.18 Mpa. The gyroscope was produced by etching silicon wafers in DRIE mode to obtain a high aspect ratio structure, tightly connected to the glass substrate by silicon/glass anode bonding technology.


Introduction
A gyroscope is a sensor that measures the rotation speed of objects [1][2][3]. In his experiment on the Earth's rotation, Jean Foucault found that a swing pendulum on a rotating platform would slowly rotate in a clockwise direction, with the tip of the swing changing constantly. He named the instrument a gyroscope, the Greek words gyro (to spin) and skopeein (to look). Early gyroscopes were generally large in volume and high in cost. The appearance of the MEMS system promoted the formation of micromechanical gyroscopes. Therefore, MEMS gyroscopes have the advantages of being easy to carry and having low power consumption [4,5].
In the continuous development of micromachined gyroscopes, various new forms of gyroscope structures have emerged, such as tuning fork gyroscopes, ring gyroscopes, laser gyroscopes, and hemispherical gyroscopes. The number of angular rates detected by the gyroscope also shifts from single to multi-axis angular rates.
In practical application, it is often necessary to obtain the angular rate information of the three axial angles of the carrier: pitch angle, yaw angle, and roll angle. Therefore, developing a new type of three-axis gyro structure has become a trend. With the development of MEMS processing technology and gyroscope design technology, many institutions have conducted in-depth research on monolithic three-axis micromechanical gyroscopes, such as a monolithic three-axis MEMS gyroscope structure with eight symmetrical plates developed by the University of Pisa [6]. However, some three-axis gyroscope structures are complex, difficult to process, and have other issues, and Z-axis anti-high overload capacity gyroscopes, such as a monolithic three-axis MEMS gyroscope structure with eight symmetrical plates developed by the University of Pisa [6]. However, some three-axis gyroscope structures are complex, difficult to process, and have other issues, and Z-axis antihigh overload capacity is unknown, as shown in Table 1. This paper proposes a new threeaxis gyroscope to provide ideas for future gyroscope design. The design has a tiny size (8.0 mm × 8.0 mm), simple structure, excellent Z-axis resistance to overload, and high zaxis sensitivity. The two mutually independent parts also avoid coupling problems. In this paper, the structure is firstly analyzed in detail, and the corresponding theoretical equations are derived. Then the structure is further simulated to verify its sensitivity and impact resistance. Finally, the detailed fabrication is introduced, and the finished product diagram is given after processing. Table 1. Comparison with a previously reported 3-axis gyroscope.

Operating Principle
A schematic diagram of the three-axis gyroscope structure introduced in this paper is shown in Figure 1. The gyroscope consists of two independent parts: the external structure includes an outer resonant ring and eight S-shaped springs for support; the internal design consists of a Y-axis sensing frame (M1, an inner cylindrical frame, X-Y plane out of motion, and a torsion around the X-axis; used to sense the Y input angular rate), Y-driven flexible joint, wheel structure driven frame (M2, a medium cylindrical shell frame, connected with four symmetrical anchors by four support beams; used to support the whole frame), X-driven flexible joint, and X-axis sensing frame (M3, an outer cylindrical frame, X-Y plane out of motion, torsion around the Y-axis; used to sense the X-axis input angular rate). The driving flexible joint transmits the electrostatic force generated by the driving comb to drive the X and Y-axes' sensing masses to rotate around the Z axis. When there is an angular rate input in the X axis, the sensing mass M3 will twist around the Y axis under the influence of the Coriolis force. Similarly, the Y-sensing mass M1 will twist around the X axis when the Y axis has an angular rate input. The distance between the X/Y sensing The driving flexible joint transmits the electrostatic force generated by the driving comb to drive the X and Y-axes' sensing masses to rotate around the Z axis. When there is an angular rate input in the X axis, the sensing mass M 3 will twist around the Y axis under the influence of the Coriolis force. Similarly, the Y-sensing mass M 1 will twist around the X axis when the Y axis has an angular rate input. The distance between the X/Y sensing mass and the bottom electrode changes after the torsion pendulum around the axis, and the angular input rate in the X/Y direction can be obtained by detecting the change of capacitance.

Mathematical Model
The vibrating gyroscope works through the Coriolis effect. The Coriolis force is proportional to the rotational angular velocity. Therefore, the angular velocity of the rotating system can be obtained by detecting Coriolis force. Because the structure adopts an independent nested structure [11][12][13][14][15], the ring and wheel structures do not affect one another, and the motion equations [16][17][18][19][20] of the two structures are given, respectively: Equation (1) is the motion equation of the resonant ring, where x and y are the amplitudes of the driving and sensing modes, m 1 , m 2 is the resonant ring's effective mass, c 1 , c 2 is the damping coefficient, and k is the stiffness coefficient [21].
Equation (2) is the motion equation of the wheel structure, where θ z is the angle at which the wheel structure rotates about the Z-axis; I ij (i = 1, 2, 3; j = x, y, z) is the moment of inertia of three parts of the wheel structure, i = 1, 2, 3 corresponds successively to the innermost Y-axis sensing mass(M 1 ), the wheel drive frame(M 2 ), and the outermost X-axis sensing mass(M 3 ); j = x, y, z corresponds to the three axes (X, Y, and Z); C ij refers to the damping coefficients; K d z is the stiffness coefficient of the driving mode; F d is the electrostatic force generated at the comb; K S ij refers to the stiffness coefficients of the sensing mode; Ω y is the angular rate of the input along the Y-axis. φ y is the displacement of the Y sensing mass rotated around the Y-axis; φ x is the displacement of the X sensing mass revolved around the X-axis. Ω x is the angular rate of the input along the X-axis. As an example, the X-axis input angular rate change in the angular coordinate system is shown in Figure 2. mass and the bottom electrode changes after the torsion pendulum around the axis, and the angular input rate in the X/Y direction can be obtained by detecting the change of capacitance.

Mathematical Model
The vibrating gyroscope works through the Coriolis effect. The Coriolis force is proportional to the rotational angular velocity. Therefore, the angular velocity of the rotating system can be obtained by detecting Coriolis force. Because the structure adopts an independent nested structure [11][12][13][14][15], the ring and wheel structures do not affect one another, and the motion equations [16][17][18][19][20] of the two structures are given, respectively: Equation (1) is the motion equation of the resonant ring, where x and y are the amplitudes of the driving and sensing modes, m1, m2 is the resonant ring's effective mass, c1, c2 is the damping coefficient, and k is the stiffness coefficient [21].
Equation (2) is the motion equation of the wheel structure, where θz is the angle at which the wheel structure rotates about the Z-axis; Iij (i = 1, 2, 3; j = x, y, z) is the moment of inertia of three parts of the wheel structure, i = 1, 2, 3 corresponds successively to the innermost Y-axis sensing mass(M1), the wheel drive frame(M2), and the outermost X-axis sensing mass(M3); j = x, y, z corresponds to the three axes (X, Y, and Z); Cij refers to the damping coefficients; K d z is the stiffness coefficient of the driving mode; Fd is the electrostatic force generated at the comb; K S ij refers to the stiffness coefficients of the sensing mode; Ωy is the angular rate of the input along the Y-axis. ϕy is the displacement of the Y sensing mass rotated around the Y-axis; ϕx is the displacement of the X sensing mass revolved around the X-axis. Ωx is the angular rate of the input along the X-axis. As an example, the X-axis input angular rate change in the angular coordinate system is shown in Figure 2.  For the ring structure n-node bending mode, the point shift change on it can be expressed as [22][23][24][25][26]: For the ring structure n-node bending mode, the point shift change on it can be expressed as [22][23][24][25][26]: u r = nq 1 (t) cos nγ + nq 2 sin nγ u γ = −q 1 (t) sin nγ + q 2 cos nγ (3) where u r is the in-plane radial displacement, u γ is the tangential displacement, γ is the angular position, and q 1 (t) and q 2 (t) are the generalized coordinate systems. The ring part of the gyroscope adopts a single-structure resonant ring, as shown in Figure 3. When the resonant ring is working, two-node bending deformation is used, n = 2. u r = 2q 1 (t) cos 2γ + 2q 2 sin 2γ u γ = −q 1 (t) sin 2γ + q 2 cos 2γ (4) r 1 2 1 2 u nq (t)cosn nq sinn u q (t)sinn q cosn where ur is the in-plane radial displacement, uγ is the tangential displacement, γ is the angular position, and q1(t) and q2(t) are the generalized coordinate systems.
The ring part of the gyroscope adopts a single-structure resonant ring, as shown in Figure 3. When the resonant ring is working, two-node bending deformation is used, n = 2.

Stiffness Calculation of S-Shaped Springs
Micro-springs are an essential part of MEMS [27], which can store mechanical energy and provide elastic force. They are usually used in microsensors, micro actuators, and MEMS gyroscopes. Since S-shaped springs can reduce the structural stiffness and capture smaller signals, and the design without a right angle makes the residual stress of these Sshaped springs less than that of the straight beam and the crab beam, combined with the above advantages, S-shaped springs are used in the design of the resonant ring support beam.
The deformation energy of the cantilever mainly includes axial tensile deformation energy and bending deformation energy, so the strain energy and radial displacement of the cantilever are [28,29]: where E is the elastic modulus of the S-shaped springs, M(x) is the bending moment acting on the cross-section of the S-shaped springs, A is the cross-sectional area of the S-shaped springs, FN(x) is the positive axial tension acting on the cross-section of the S-shaped springs, and I is the moment of inertia of the section of the S-shaped springs. Taking the cantilever beam at this level as an example, the left end of the cantilever beam is fixed at the anchorage point, and a load FN opposite the X-axis direction is applied to the right end. The simplified structure is shown in Figure 4.

Stiffness Calculation of S-Shaped Springs
Micro-springs are an essential part of MEMS [27], which can store mechanical energy and provide elastic force. They are usually used in microsensors, micro actuators, and MEMS gyroscopes. Since S-shaped springs can reduce the structural stiffness and capture smaller signals, and the design without a right angle makes the residual stress of these S-shaped springs less than that of the straight beam and the crab beam, combined with the above advantages, S-shaped springs are used in the design of the resonant ring support beam.
The deformation energy of the cantilever mainly includes axial tensile deformation energy and bending deformation energy, so the strain energy and radial displacement of the cantilever are [28,29]: where E is the elastic modulus of the S-shaped springs, M(x) is the bending moment acting on the cross-section of the S-shaped springs, A is the cross-sectional area of the S-shaped springs, F N (x) is the positive axial tension acting on the cross-section of the S-shaped springs, and I is the moment of inertia of the section of the S-shaped springs. Taking the cantilever beam at this level as an example, the left end of the cantilever beam is fixed at the anchorage point, and a load F N opposite the X-axis direction is applied to the right end. The simplified structure is shown in Figure 4. Part 1 : The displacement of Part 2 is: Part ①: The displacement of Part 2 is: ( ) (1 2 cos cos ) The displacement of Part 3 is: Part ④: The displacement of Part 4 is: The displacement of Part 3 is: The displacement of Part 4 is: Part 5 : The displacement of part 5 is: Part 6 : The displacement of Part 6 is: The displacements of Parts 7 and 9 are the same as those of Part 5: The displacement of Part 8 is the same as that of the part 4: The displacement of Part 10 is the same as the that of Part 6: The displacement of Part 11 is: The displacement of Part 12 is: The displacement of Part 13 is: The formula for calculating the cantilever beam stiffness is: Assuming that the width of the ring is W r , m eff is the effective mass of the resonant ring, and µ is the Poisson's ratio, the equation for the stiffness of the resonant ring is as follows: Therefore, the resonant frequency can be calculated as:

Drive Force Calculation
A. Ring Structure The driving mode of a gyroscope can be divided into electrostatic, piezoelectric, electromagnetic, electric, optical, and so on. Due to the advantages of simple implementation, high sensitivity, and a low-temperature coefficient of electrostatic drive, this method is adopted to excite the gyroscope. The resonant ring adopts a variable spacing drive. The ring part is tested by eight main electrodes and eight auxiliary electrodes. As shown in Figure 5, the pair of 0 • and 180 • electrodes constitute the driving electrode, the team of 90 • and 270 • electrodes form the driving detection electrode, the pair of 45 • and 225 • electrodes comprise the detection electrode, and the pair of 135 • and 315 • electrodes are the orthogonal electrode. Since the displacement generated by the gyroscope during driving is minimal, the ring capacitor can be equivalent to the plate capacitor, as shown in Figure 6 [30].
A. Ring Structure The driving mode of a gyroscope can be divided into electrostatic, piezoelectric, electromagnetic, electric, optical, and so on. Due to the advantages of simple implementation, high sensitivity, and a low-temperature coefficient of electrostatic drive, this method is adopted to excite the gyroscope. The resonant ring adopts a variable spacing drive. The ring part is tested by eight main electrodes and eight auxiliary electrodes. As shown in Figure 5, the pair of 0° and 180° electrodes constitute the driving electrode, the team of 90° and 270° electrodes form the driving detection electrode, the pair of 45° and 225° electrodes comprise the detection electrode, and the pair of 135° and 315° electrodes are the orthogonal electrode. Since the displacement generated by the gyroscope during driving is minimal, the ring capacitor can be equivalent to the plate capacitor, as shown in Figure  6 [30].  The parallel plate capacitance formula can be expressed as: where ε is the vacuum dielectric constant, θ is the central angle corresponding to the arc, R is the radius of the ring, h is the structure's thickness, and d is the distance between two plates. When the plate moves Δd and the driving voltage Vd is applied between the two plates, the electrostatic force Frd is generated as follows: B. Wheel Structure The driving part of the wheel structure (M2) adopts a scalloped comb and differential electrostatic driving [31]. The driving voltage is Vwd+ and Vwd-, respectively: The driving voltage is designed as a superposition of DC (direct current) and AC (alternating current), where ω represents the driving mode angular frequency. Therefore, the electrostatic driving torque of the wheel structure can be expressed as: In the formula, Cwd+ and Cwd-respectively represent the capacitance formed by the The parallel plate capacitance formula can be expressed as: where ε is the vacuum dielectric constant, θ is the central angle corresponding to the arc, R is the radius of the ring, h is the structure's thickness, and d is the distance between two plates. When the plate moves ∆d and the driving voltage V d is applied between the two plates, the electrostatic force F rd is generated as follows: B. Wheel Structure The driving part of the wheel structure (M 2 ) adopts a scalloped comb and differential electrostatic driving [31]. The driving voltage is V wd+ and V wd-, respectively: The driving voltage is designed as a superposition of DC (direct current) and AC (alternating current), where ω represents the driving mode angular frequency. Therefore, the electrostatic driving torque of the wheel structure can be expressed as: In the formula, C wd + and C wd-respectively represent the capacitance formed by the movable comb and the fixed comb on both sides, as shown in Figure 7; α is the overlapping angle between the movable comb and the fixed comb; ∆α is the deflection angle of the movable comb; h d is the distance between the moving comb and the fixed comb; r i is the radius of the ith moving comb tooth; h is the thickness of the structure. After substituting the voltage Formula (28), the electrostatic driving torque is as follows: Sensors 2022, 13, x FOR PEER REVIEW 9 of 20 It can be seen that the electrostatic driving torque is only related to the applied voltage rather than the angular displacement.

Vd+
Vdα α Figure 7. Schematic diagram of the wheel structure driving comb.

Sensing Capacitance
A. Ring Structure When the resonant ring is subjected to the Coriolis force, the plate spacing changes, and the capacitance changes along with the displacement.
The electrode diagram for the sensing mode is shown in Figure 8. Suppose the driving electrode is at angle θ1, and the corresponding central angle is ϕ; thus, the capacitance Crs of the sensing electrode can be written as:  The drive signal can be written in the form of f = Fdcos(ωdt), where ωd is the resonant frequency. Combining Equation (1) and the sensitivity equation, the sensitivity expression is: It can be seen that the electrostatic driving torque is only related to the applied voltage rather than the angular displacement.

Sensing Capacitance
A. Ring Structure When the resonant ring is subjected to the Coriolis force, the plate spacing changes, and the capacitance changes along with the displacement.
The electrode diagram for the sensing mode is shown in Figure 8. Suppose the driving electrode is at angle θ 1 , and the corresponding central angle is φ; thus, the capacitance C rs of the sensing electrode can be written as: Sensors 2022, 13, x FOR PEER REVIEW 9 of 20 It can be seen that the electrostatic driving torque is only related to the applied voltage rather than the angular displacement.

Vd+
Vdα α Figure 7. Schematic diagram of the wheel structure driving comb.

Sensing Capacitance
A. Ring Structure When the resonant ring is subjected to the Coriolis force, the plate spacing changes, and the capacitance changes along with the displacement.
The electrode diagram for the sensing mode is shown in Figure 8. Suppose the driving electrode is at angle θ1, and the corresponding central angle is ϕ; thus, the capacitance Crs of the sensing electrode can be written as:  The drive signal can be written in the form of f = Fdcos(ωdt), where ωd is the resonant frequency. Combining Equation (1) and the sensitivity equation, the sensitivity expression is: where ω 1 and ω 2 are the drive and sensing frequencies, respectively, when ∆d reaches its maximum value. At this time, the maximum value of vibration amplitude is reached under the sensing mode, so the relationship between the amount of capacitance change and the input angular velocity can be obtained as: B. Wheel Structure The wheel structure adopts rotating plate capacitance sensing. When the angular rate is input, the sensing mass rotates around the axis under the action of the Coriolis force, and the distance and area between it and the bottom electrode changes.
As shown in Figure 9, θ x is the deflection angle of the sensing mass when it is twisted around the Y-axis; R 2 is the outer radius of the sector electrode; R 1 is the inner radius of the sector electrode; β is the central angle corresponding to the sector electrode; l 1 is the distance when the plate is parallel. In this case, the calculation formula of capacitance variation can be expressed as follows: Sensors 2022, 13, x FOR PEER REVIEW 10 of 20 under the sensing mode, so the relationship between the amount of capacitance change and the input angular velocity can be obtained as: B. Wheel Structure The wheel structure adopts rotating plate capacitance sensing. When the angular rate is input, the sensing mass rotates around the axis under the action of the Coriolis force, and the distance and area between it and the bottom electrode changes.
As shown in Figure 9, θx is the deflection angle of the sensing mass when it is twisted around the Y-axis; R2 is the outer radius of the sector electrode; R1 is the inner radius of the sector electrode; β is the central angle corresponding to the sector electrode; l1 is the distance when the plate is parallel. In this case, the calculation formula of capacitance variation can be expressed as follows:  Figure 9. Schematic diagram of the sensing capacitance.
The semi-circular Y-axis detection electrode diagram is shown in Figure 10. The detection principle of the electrode is similar to that of the X-axis detection electrode. The change of the Y-axis detection capacitance value due to the influence of the Coriolis force can be obtained by the following equation: The semi-circular Y-axis detection electrode diagram is shown in Figure 10. The detection principle of the electrode is similar to that of the X-axis detection electrode. The change of the Y-axis detection capacitance value due to the influence of the Coriolis force can be obtained by the following equation: where R 3 represents the outer radius of the disc, a 1 represents the vertical distance between the origin and the disk-shaped electrode, θ y represents the central angle corresponding to the disc, and l 2 represents the initial distance between the upper and lower plates.   (35) where R3 represents the outer radius of the disc, a1 represents the vertical distance between the origin and the disk-shaped electrode, θy represents the central angle corresponding to the disc, and l2 represents the initial distance between the upper and lower plates. The calculation principle of the sensitivity of the wheel structure is similar to Equation (32), and the calculation results are as follows: where Iz =  The calculation principle of the sensitivity of the wheel structure is similar to Equation (32), and the calculation results are as follows: where C iz , and ω d z , ω s y , and ω s x are the X/Y-axis driving frequency, Y-axis sensing frequency, and X-axis sensing frequency, respectively. The relationship between the amount of capacitance change and the input angular velocity can be obtained as:

Modal Analysis and Harmonic Response Analysis
After the gyroscope structure was determined, finite element simulation of the gyroscope structure was carried out by ANSYS. The structure was processed by single crystal silicon, and the material parameters are shown in Table 2. The modal frequency of the gyroscope structure was obtained. The working mode of the three-axis gyroscope is shown in Figure 11. From the simulation results, it can be observed that the X/Y drive frequency was 5954.8 Hz, the Y-axis detection frequency was 5774.5 Hz, the X-axis detection frequency was 6030.5 Hz, and the maximum frequency difference was 256 Hz. The Z-axis drive frequency was 10,728 Hz, the Z-axis detection frequency was 10,725 Hz, the maximum frequency difference of Z was 3 Hz, and the frequency difference was slight, so the Z-axis sensitivity of the gyroscope was high. The variation of mechanical sensitivity with the frequency ratio is shown in Figure 12, when     Based on the modal simulation, harmonic response analysis of the structure was carried out, as shown in Figure 13. The relationship between the driving voltage and electrostatic driving force, driving voltage, and electrostatic driving torque can be obtained by taking the parameter values in Table 3 for Equations (27) and (30). The electrostatic force and torque are 0.15 µN and 6.7 × 10 −12 N/m, respectively, as shown in Figures 14 and 15, so harmonic force with amplitude of 0.1µm is applied to the gyroscope, and the displacement of the structure sensing mode is observed. The displacement of the X, Y, and Z sensing masses was 7.5, 10, and 7.7 µm, respectively.

Transient Shock Response Analysis
Because the gyroscope is often mounted on the gun, it will suffer a vast transient impact, which will cause the gyroscope structure to be destroyed, so the gyroscope structure often needs to have the ability to resist high overload.
The transient analysis module of ANSYS simulates the anti-high overload capability of the gyroscope. A half-sine periodic impact load of 10,000 g@5 ms was applied to the zaxis direction of the gyroscope, and the stress diagram is shown in Figure 16. At this time, the maximum stress of the structure is 300.18 MPa, which is much smaller than the allowable stress, and it can be seen that the structure has good impact resistance.

Transient Shock Response Analysis
Because the gyroscope is often mounted on the gun, it will suffer a vast transient impact, which will cause the gyroscope structure to be destroyed, so the gyroscope structure often needs to have the ability to resist high overload.
The transient analysis module of ANSYS simulates the anti-high overload capability of the gyroscope. A half-sine periodic impact load of 10,000 g@5 ms was applied to the zaxis direction of the gyroscope, and the stress diagram is shown in Figure 16. At this time, the maximum stress of the structure is 300.18 MPa, which is much smaller than the allowable stress, and it can be seen that the structure has good impact resistance.

Transient Shock Response Analysis
Because the gyroscope is often mounted on the gun, it will suffer a vast transient impact, which will cause the gyroscope structure to be destroyed, so the gyroscope structure often needs to have the ability to resist high overload.
The transient analysis module of ANSYS simulates the anti-high overload capability of the gyroscope. A half-sine periodic impact load of 10,000 g@5 ms was applied to the z-axis direction of the gyroscope, and the stress diagram is shown in Figure 16. At this time, the maximum stress of the structure is 300.18 MPa, which is much smaller than the allowable stress, and it can be seen that the structure has good impact resistance.

Transient Shock Response Analysis
Because the gyroscope is often mounted on the gun, it will suffer a vast transient impact, which will cause the gyroscope structure to be destroyed, so the gyroscope structure often needs to have the ability to resist high overload.
The transient analysis module of ANSYS simulates the anti-high overload capability of the gyroscope. A half-sine periodic impact load of 10,000 g@5 ms was applied to the zaxis direction of the gyroscope, and the stress diagram is shown in Figure 16. At this time, the maximum stress of the structure is 300.18 MPa, which is much smaller than the allowable stress, and it can be seen that the structure has good impact resistance.

Fabrication
Accelerometers, relays, and gyroscopes are usually processed by SOG (silicon on glass) technology, which is relatively simple and has a very low parasitic capacitance [32][33][34]. The structure was manufactured with SOG. Because the aspect ratio is directly related to the gyroscope performance, the DRIE [35,36]. process was used in the etching step to ensure that the gyroscope structure has a high aspect ratio and better performance. Due to the low temperature of the anode bonding process, the influence of residual stress and strain after bonding can be weakened, and the bonding strength and stability were high. The vacuum sealing performance was good, and vacuum sealing performance is closely related to the sensitivity of the gyroscope. After synthesizing the advantages mentioned above, the anode bonding process was adopted in the processing. The processing process of the structure is shown in Figure 17.

Fabrication
Accelerometers, relays, and gyroscopes are usually processed by SOG (silicon on glass) technology, which is relatively simple and has a very low parasitic capacitance [32][33][34]. The structure was manufactured with SOG. Because the aspect ratio is directly related to the gyroscope performance, the DRIE [35,36]. process was used in the etching step to ensure that the gyroscope structure has a high aspect ratio and better performance. Due to the low temperature of the anode bonding process, the influence of residual stress and strain after bonding can be weakened, and the bonding strength and stability were high. The vacuum sealing performance was good, and vacuum sealing performance is closely related to the sensitivity of the gyroscope. After synthesizing the advantages mentioned above, the anode bonding process was adopted in the processing. The processing process of the structure is shown in Figure 17.
The processing results are shown in Figure 18.   The processing results are shown in Figure 18.

Conclusions
In this paper, a new three-axis gyroscope structure was proposed. The frame was nested by two independent systems, its design idea was given, and the motion equation of the form was deduced. The ring-shaped part of the structure is driven by static electricity with variable spacing, while the wheel structure is driven by static electricity with a variable area. During the detection, the outer resonant ring resonates along the direction of 45 • and 135 • , and the sensing mass of wheel will twist around the X and Y axes, respectively. The capacitance variation during the sensing mode was obtained according to the motion characteristics, and the relation equation between angular velocity and capacitance variation is obtained. In the design of the cantilever beam, S-shaped springs were used to reduce stiffness and improve sensitivity. In order to calculate the resonant frequency of the resonant ring, the stiffness calculation formula of the folded beam was given. After completing the gyroscope structure design, the specific modal frequency of the gyroscope was obtained by combining the finite element simulation software ANSYS. Moreover, the harmonic response analysis proved that the structure had high Z-axis sensitivity. In addition, in order to explore the anti-high overload performance of Z-axis direction of the gyroscope, a transient analysis was performed on it. It was found that the stress of the structure was small under the impact of 10,000 g@5 ms, which proved that the gyroscope has good performance in Z-axis anti-high overload. Finally, a structure machining method by the SOG process combined with the DRIE etching method was introduced.